SERVICE MANUAL FM STEREO/FM-AM RECEIVER. US Model Canadian Model E Model Australian Model Tourist Model SPECIFICATIONS

Transcription

1 STR-W77 SERVICE MANUAL US Model Canadian Model E Model Australian Model Tourist Model STR-W77 is RECEIVER section in MHC-W77AV. SPECIFICATIONS With 6 ohm loads, both channels driven, from 40 20, 000 Hz; rated 100 watts per channel minimum RMS power, with no more than 0.9 % total harmonic distortion from 250 milliwatts to rated output. (US model) Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range EXCEPT Tourist model : MHz Tourist model : MHz Antenna FM lead antenna Antenna terminals 75 ohm, unbalanced Intermediate frequency AM tuner section Tuning range Antenna Intermediate frequency 10.7 MHz US, Canadian, E2, Argentine, Australian, Thailand model : AM : 530 1,710kHz (10kHz) 531 1,710kHz (9kHz) E3, Saudi Arabia, Hong Kong, Singapore, Malaysia, Tourist model : MW : 531 1,602kHz (9kHz) SW : MHz (9kHz) AM loop antenna, External antenna terminals 450 khz Amplifier section Continuous RMS power output US model : (FRONT) 100 W W (6 ohms at 40 20,000 Hz, 0.9% THD) 120 W W (6 ohms at 1 khz, 5% THD) (CENTER) 30 W (8 ohms at 1 khz, 5% THD) (REAR) 15 W + 15 W (8 ohms at 1 khz, 5% THD) EXCEPT US model : (FRONT) 120 W W (6 ohms at 1 khz, 5% THD) (CENTER) 30 W (8 ohms at 1 khz, 5% THD) (REAR) 15 W + 15 W (8 ohms at 1 khz, 5% THD) Inputs VIDEO/MD IN (phono jacks) : voltage 250 mv/450 mv impedance 47 kilohms MIX MIC (phono jacks) : sensitivity 1 mv/450 mv impedance 10 kilohms Outputs VIDEO/MD OUT (phono jacks) : voltage 250 mv impedance 1 kilohms PHONES (stereo phono jacks) : accepts headphones of 8 ohms or more FRONT SPEAKER : accepts impedance of 6 to 16 ohms CENTER SPEAKER : accepts impedance of 8 to 16 ohms REAR SPEAKER : accepts impedance of 8 to 16 ohms SUPER WOOFER : voltage 250 mv impedance 1 kilohms Continued on page 2 FM STEREO/FM-AM RECEIVER MICROFILM

2 General Power requirements Power consumption US, Canadian model : 120 V AC, 60 Hz Australian model : 240 V AC, 50/60Hz Thailand model : 220 V AC, 50/60Hz Other models : V/ V AC adjustable, 50/60 Hz EXCEPT Canadian model : 260 watts Canadian model : 350 VA Dimensions Approx. 280 x 205 x 345 mm (11x 8 1 / 16 x 13 9 / 16 in.) (w/h/d) Mass Approx. 6.4 kg (14 lb 2 oz) Design and specifications are subject to change without notice. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. MODEL INDENTIFICATION BACK PANEL TABLE OF CONTENTS Section Title Page Specifications GENERAL TEST MODE ELECTRICAL ADJUSTMENTS EXPLANATION OF IC TERMINALS DIAGRAMS 5-1. Printed Wiring Boards Main Section Schematic Diagram Main Section Schematic Diagram Panel Section Printed Wiring Boards Panel Section Schematic Diagram TCB Section (US, CND, E2, AR, AUS, TH model) Printed Wiring Boards TCB Section (US, CND, E2, AR, AUS, TH model) Printed Wiring Boards TCB Section (E3, EA, MY, SP, HK, JE model) Schematic Diagram TCB Section (E3, EA, MY, SP, HK, JE model) EXPLODED VIEWS 6-1. Chassis Section Front Panel Section ELECTRICAL PARTS LIST SAFETY-RELATED COMPONENT WARNING!! Parts No. Model π US π Canadian π E, Saudi Arabia, Argentine, Torist π Australian π Hong Kong π Malaysia, Singapore π Thailand COMPONENTS IDENTIFIED BY MARK! OR DOTTED LINE WITH MARK! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2

3 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer : Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. µ 0.15 F To Exposed Metal Parts on Set 1.5kΩ AC Voltmeter (0.75V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. 3

4 SECTION 1 GENERAL This section is extracted from instruction manual. INDEX TO PARTS AND CONTROLS 4

5 SECTION 2 TEST MODE DISPLAY / KEY TEST MODE Press the ENTER/NEXT and FUNCTION buttons simultaneously. Then press the MENU 1 button with the following 4 seconds to set the Test Mode. 1. The message W3 NA (destination) appears on the screen and a 32 cycle square wave of the subcrystal oscillator is output from Pin 24 (AUB. OUT). 2. Press any key to rotate JOG and all FL indicators light up. When you rotate JOG at this point, the display changes as follows. N all FL indicators on Nn FL pattern 1 Nn FL pattern 2 n The changes and all LED indicators light up. 3. Again press any key to set the key count check. The following display appears The numbers in order from left to right show ; the number of keys pressed, the JOG count (1 click per 4 counts), and the VOL count. (1 cycle is a count of 96.) 4. Press the Power button to reset to the factory settings. AMP TEST MODE Press the ENTER/NEXT and FUNCTION buttons simultaneously. Then press the MENU 2 button with the following 4 seconds to set the Test Mode. 1. The message AMP TEST appears on the screen. Press the MENU button to call up the Equalizer Curve for the Amp Test. However when the function is set to the tuner, use the MENU button to call up each tuner preset from 1 through Press the Power button to reset to the factory settings. MICROCOMPUTER COLD START Press the ENTER/NEXT and FUNCTION buttons simultaneously. Then press the MENU 3 button with the following 4 seconds to reset the microcomputer to the factory settings. SUBCRYSTAL TEST MODE Press the ENTER/NEXT and FUNCTION buttons simultaneously. Then press the MENU 4 button with the following 4 seconds. The message XTAL TEST appears on the screen and a 32 cycle square wave of the subcrystal oscillator is output from Pin 24 (AUB.OUT). In addition, a square wave of the same frequency as the subcrystal oscillator, is output from 4PIN (POWER. ON/OFF). Press the Power button to reset to the factory settings. 5

6 SECTION 3 ELECTRICAL ADJUSTMENTS Precautions in Repairing Note. 1 : The adjustment should be performed in the publication. (MW n FM n SW) Note. 2 : As a front-end (FE1) is difficult to repair if faulty, replace it with new one. rabbreviation AUS : Australian AR : Argentine EA : Saudi Arabia HK : Hong Kong SP : Singapore JE : Tourist MY : Malaysia TH : Thailand CND : Canadian E2 : Tuner sections SW BAND do not exist. E3 : Tuner sections SW BAND exist. MW SECTION MW Tuned Indication Lighting Level Setting : Band : MW loop antenna A loop antenna B SW Control Voltage Adjustment (Frequency Coverge Adjustment) (E3, EA, MY, SP, HK, JE model) Setting : Band : SW Procedure : 1. Connect digital Voltmeter to diode D1 center lead and ground. 2. Adjust for a following value reading on digital Voltmeter. SW Set frequency Adjustment part Reading on digital voltmeter 5.95MHz T2 1.2Vdc 17.9MHz CV2 8.5Vdc SW Tracking Adjustment (E3, EA, MY, SP, HK, JE model) Setting : Band : SW AM RF signal generator VTVM AM RF signal generator set + set Modulation : 400Hz 30% modulation SPEAKER terminal Carrier frequency : 999kHz (at 9kHz step) 1,050kHz (at 10kHz step) Procedure : 1. Set loop antenna A so that the loop antenna B input level becomes 55dBµ/m (0.6mV/m) 2. Tune the set to 999kHz or 1,050kHz. 3. Adjust RV41 so that the TUNED indicatior goes on. FM SECTION FM Tuned Indication Lighting Level Note : Always make the tuning level adjustment first. (Since it affects the FM tuning level.) Setting : Band : FW Procedure : Adjust for maximum reading on VTVM. SW Set frequency 7MHz 17MHz AM ANTENNA terminal Adjustment part T1 CV1 r Repeat the procedures is each adjustment several times, and the frequency coverage and tracking adjustment should be finally done by the trimmer capacitors. Adjustment Location : TCB board FM RF stereo signal generator FM ANTENNA terminal 75 Ω coaxial Carrier frequency : 98MHz Modulation : OFF Output level : 0.018mV (25dB ) µ set Procedure : 1. Tune the set to 98MHz. 2. Adjust RV42 so that the TUNED indicator goes on. 6

7 Adjustment Location [TCB BOARD] Component side CV1 : SW Tracking Adjustment T1 : SW Tracking Adjustment RV41 : MW Tuned indication Lighting Level CV2 : SW Control Voltage Adjustment T2 : SW Control Voltage Adjustment D1 FE1 RV42 : FW Tuned indication Lighting Level 7

8 IC501 ASD0205GF-015-3BA (SYSTEM CONTOROL) SECTION 4 EXPLANATION OF IC TERMINALS Pin No. Pin name I/O 1 VDD Power supply. 2 CLK OUT O Direct output for communications with HCD-W55. 3 RDY IN I/O Direct input / output for communications with HCD-W55. 4 POWER ON / OFF O L : Relay ON 5 MUTE O Mute output to transistor. L : Mute ON 6 PROLOGIC LATCH O Latch output to IC3001 (LA2785). 7 VOL. LATCH O Latch output to IC2002 (TC9210P) LAT O Latch output to IC105 (M62427FP). 9 LED LAT O Latch output to IC504 (M66313FP-200C). 10 RESET I Reset terminal. 11 X2 Oscillator connection terminal. (5MHz) 12 X1 Oscillator connection terminal. (5MHz) 13 IC Ground connection. 14 XT2 Oscillator connection terminal. (32MHz) 15 XT1 Oscillator connection terminal. (32MHz) 16 VDD Power supply. 17 BACK UP I AC Power supply OFF. 18 COM CLK O Transfer clock output serial data. 19 COM DATA O Serial data output. 20 ST DATA IN I Serial data input from IC ST CE O Chip enable output to IC STEREO I Stereo signal input. 23 TUNED I Tuned signal input. 24 AUB OUT O Audio bus output. 25 AVSS Ground. 26 PROLOGIC. RY O Rear and center speaker relay ON/OFF control. 27 SUFFIX I Input for model select. 28 SPE I Spectrum analyzer signal input. 29 SPE I Spectrum analyzer signal input. 30 SPE I Spectrum analyzer signal input. 31 SPE I Spectrum analyzer signal input. 32 KYE 1 I Key data input (A/D converter). 33 KYE 2 I Key data input (A/D converter). 34 AVDD Power supply for anlog. 35 AV REF Reference voltage for A/D converter. 8

9 Pin No. Pin name I/O 36 VOL IN A I Volume encoder input. 37 JOG IN A I JOG dial encoder input. 38 RDS CLK I Not uset. 39 AUB IN I Audio bus output. 40 VSS Ground. 41 RDS DATA I Not uset. 42 D 3 I/O System control data signal input / output. 43 D 2 I/O System control data signal input / output. 44 D 1 I/O System control data signal input / output. 45 D 0 I/O System control data signal input / output. 46 VDD Power supply +5V. 47 SIRCS IN I SIRCS signal input. 48 VOL IN B I Volume encoder input. 49 JOG IN B I JOG dial encoder input. 50 ST FM O 51 ST MUTE O BAND select output. FM Receiving AM Receiving MUTE %º pin H L H % pin L L H 52 EMG OUT O Urgent signal standby output. H : standby 53 EMG IN I Urgent signal start input. H n L : start P 32 P 8 O Segment output to FL VG Power supply for fluorescent indicator tube P 7 P 1 O Segment output to FL G 1 G O Grid output for FL501. 9

10 10

11 11

12

13

14

15

16

17

18

19

20 SECTION 6 EXPLODED VIEWS NOTE : r -XX, -X mean standardized parts, so they may have some difference from the original one. r Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items CHASISS SECTION r The mechanical parts with no reference number in the exploded views are not supplied. r Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. r Abbreviation CND : Canadian SP : Singapore AUS : Australian HK : Hong Kong AR : Argentine JE : Tourist TH : Thailand EA : Saudi Arabia MY : Malaysia E2 : Tuner sections SW band do not exist. E3 : Tuner sections SW band exist. 8 9 F853, , #1 #2 F851 not supplied 8 #1 T E, EA, MY, SP, HK, AR, JE model #3 8 F852 #3 not supplied #3 The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. E, EA, MY, SP, HK, AR, JE model 23 S #4 11 #4 6 3 #2 2 4 not supplied #2 #2 not supplied #2 #3 16 M601 #5 18 #5 14 #4 #3 12 #4 24 #1 1 not supplied E801 #3 US, CND model E, JE model EA, MY, SP, AR, HK model TH model AUS model E3, JE model HK model 22 EA, MY, SP model 35

21 KNOB (M)! CORD, POWER (EA,MY,SP,HK,AR) * BUSHING (2104), CORD (EXCEPT E, TH, JE)! CORD, POWER (E,JE) BUSHING (S) (4516), CORD (TH)! CORD, POWER (US,CND) BUSHING (S) (FBS002), CORD (E,JE)! CORD, POWER (AUS) * CONNECTION BOARD! CORD, POWER (TH) * 4 A A POWER (B) BOARD, COMPLETE (US) * 4 A A POWER (B) BOARD, COMPLETE (CND) * 4 A A POWER (B) BOARD, COMPLETE (E,EA,HK,AR,AUS,JE) * 4 A A POWER (B) BOARD, COMPLETE (MY) * 4 A A POWER (B) BOARD, COMPLETE (SP) * 4 A A POWER (B) BOARD, COMPLETE (TH) * 5 A A POWER (A) BOARD, COMPLETE (US) * 5 A A POWER (A) BOARD, COMPLETE (CND) * 5 A A POWER (A) BOARD, COMPLETE (E,EA,HK,AR,AUS,JE) * 5 A A POWER (A) BOARD, COMPLETE (MY) * 5 A A POWER (A) BOARD, COMPLETE (SP) * 5 A A POWER (A) BOARD, COMPLETE (TH) SCREW (CASE) (M3X8) CASE (EXCEPT MY,SP) CASE (MY,SP) FUSE HOLDER * TRANSFORMER SECONDARY BOARD * TRANS (A) BOARD * HOOK * SP BOARD * 13 A A MAIN BOARD, COMPLETE (US) * 13 A A MAIN BOARD, COMPLETE (CND) * 13 A A MAIN BOARD, COMPLETE (E,EA,HK,AR,AUS,JE) * 13 A A MAIN BOARD, COMPLETE (MY) * 13 A A MAIN BOARD, COMPLETE (SP) * 13 A A MAIN BOARD, COMPLETE (TH) 14 A A TCB BOARD, COMPLETE (US,CND) 14 A A TCB BOARD, COMPLETE (E3,EA,MY,SP,HK) 14 A A TCB BOARD, COMPLETE (E2,AR,AUS) 14 A A TCB BOARD, COMPLETE (JE) 14 A A TCB BOARD, COMPLETE (TH) * VOLTAGE SW BOARD (E,EA,MY,SP,HK,AR,JE) * SENSOR BOARD * HEAT SINK! ADAPTER, CONVERSION 2P (E3,JE)! ADAPTER, CONVERSION 2P (EA,MY,SP)! ADAPTOR, CONVERSION PLUG 3P (HK) * PLATE, JACK (US) * PLATE, JACK (CND) * PLATE, JACK (E,EA,AR,JE) * PLATE, JACK (AUS) * PLATE, JACK (HK) * PLATE, JACK (MY,SP) * PLATE, JACK (TH) SCREW, TAPPING * LABEL, FUSE RATING (3.15A/250V) (US,CND) * LABEL, FUSE RATING (2.5A/250V)(US) E PLATE, GROUND! F FUSE, TIME LAG (T2AL) (TH,AUS)! F FUSE, TIME LAG (T4AL) (EXCEPT US,CND,TH,AUS)! F FUSE (5A/125V) (CND)! F FUSE (6A/125V) (US)! F FUSE, TIME LAG (T4AL) (E,EA,MY,SP,HK,AR,JE)! F FUSE, TIME LAG (T3.15AL)! F FUSE (3.15A/250V) (US,CND)! F FUSE, TIME LAG (T3.15AL)! F FUSE (3.15A/250V) (US,CND)! F FUSE, TIME LAG (T3.15AL)! F FUSE, MICRO (3.15A) (US)! F FUSE (3.15A/250V) (CND)! F FUSE, TIME LAG (T3.15AL)! F FUSE (3.15A/250V) (CND)! S SWITCH, VOLTAGE SELECTOR (E,EA,MY,SP,HK,AR,JE) M FAN, DC (TH) M FAN, DC (EXCEPT TH)! T TRANSFORMER, POWER (US,CND)! T TRANSFORMER, POWER The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 36

22 6-2. FRONT SECTION 4A : JOY ENCODER board 4B : VOL ENCODER board F A 4B 59 (including 4A, B) supplied with S supplied with S * 59 A A PANEL BOARD, COMPLETE (US,CND) 51 X PANEL ASSY, FRONT * 59 A A PANEL BOARD, COMPLETE (E3,EA,MY,SP,HK) FOOT (FELT) * 59 A A PANEL BOARD, COMPLETE (E2) KNOB (V) * 59 A A PANEL BOARD, COMPLETE (AR) KNOB (J) * 59 A A PANEL BOARD, COMPLETE (AUS) EMBLEM (4-A), SONY * 59 A A PANEL BOARD, COMPLETE (JE) * CUSHION (FL) * HOLDER, FL TUBE SCREW (2.6X8), +BVTP 59 A A PANEL BOARD, COMPLETE (TH) * HOUSE, LAMP FL INDICATOR TUBE, FLUORESCENT 37

23 CONNECTION MAIN SECTION 7 ELECTRICAL PARTS LIST NOTE : r Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. r -XX, -X mean standardized parts, so they may have some difference from the original one. r RESISTORS All resistors are in ohms METAL : Metal-film resistor METAL OXIDE :Metal oxide-film resistor F : nonflammable r Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. r SEMICONDUCTORS In each case, u : µ, for example : ua... : µ A..., upa... : µ PA... upb... : µ PB..., upc... : µ PC... upd... : µ PD... r CAPACITORS uf : µ F r COILS uh : µ H r Abbreviation CND : Canadian SP : Singapore AUS : Australian HK : Hong Kong AR : Argentine JE : Tourist TH : Thailand EA : Saudi Arabia MY : Malaysia E2 : Tuner sections SW band do not exist. E3 : Tuner sections SW band exist. The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board. * CONNECTION BOARD C ELECT 4.7uF 20% 50V ***************** C ELECT 0.22uF 20% 50V < CONNECTOR > * CN SOCKET, CONNECTOR 8P * CN SOCKET, CONNECTOR 8P ************************************************************ * A A MAIN BOARD, COMPLETE (US) * A A MAIN BOARD, COMPLETE (CND) * A A MAIN BOARD, COMPLETE (E,EA,HK,AR,AUS,JE) * A A MAIN BOARD, COMPLETE (MY) * A A MAIN BOARD, COMPLETE (SP) * A A MAIN BOARD, COMPLETE (TH) ********************* FUSE HOLDER * HEAT SINK * HEAT SINK SCREW +BVTT 3X6 (S) < CAPACITOR > C FILM 0.15uF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C FILM 0.22uF 5% 50V C FILM 0.22uF 5% 50V C FILM 0.068uF 5% 50V C FILM 0.068uF 5% 50V C FILM 0.018uF 5% 50V C FILM 0.018uF 5% 50V C CERAMIC uF 10% 50V C CERAMIC 4700PF 10% 50V C CERAMIC 4700PF 10% 50V C ELECT 4.7uF 20% 50V C ELECT 4.7uF 20% 50V C FILM 0.12uF 5% 50V C FILM 0.12uF 5% 50V C ELECT 2.2uF 20% 100V C CERAMIC 0.01uF 30% 16V C ELECT 10uF 20% 50V C ELECT 4.7uF 20% 50V C ELECT 1uF 20% 50V C ELECT 10uF 20% 50V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C CERAMIC 0.01uF 30% 16V C FILM 0.22uF 5% 50V C FILM 0.22uF 5% 50V C FILM 0.068uF 5% 50V C FILM 0.068uF 5% 50V C FILM 0.018uF 5% 50V C FILM 0.018uF 5% 50V C CERAMIC uF 10% 50V C CERAMIC 4700PF 10% 50V C CERAMIC 4700PF 10% 50V C ELECT 4.7uF 20% 50V C ELECT 4.7uF 20% 50V C FILM 0.12uF 5% 50V C FILM 0.12uF 5% 50V C ELECT 2.2uF 20% 100V C CERAMIC 0.01uF 30% 16V C ELECT 10uF 20% 50V C ELECT 4.7uF 20% 50V C ELECT 4.7uF 20% 50V C ELECT 1uF 20% 50V C ELECT 47uF 20% 50V C ELECT 47uF 20% 50V C CERAMIC 0.01uF 30% 16V C ELECT 10uF 20% 50V C CERAMIC 220PF 10% 50V C ELECT 4.7uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V 38

24 MAIN C CERAMIC 0.01uF 30% 16V C CERAMIC 0.1uF 50V C CERAMIC 0.01uF 30% 16V C ELECT 10uF 20% 50V C CERAMIC CHIP 220PF 10% 50V C CERAMIC CHIP 680PF 10% 50V C ELECT 4.7uF 20% 50V C CERAMIC 0.1uF 50V C CERAMIC 0.01uF 30% 16V C ELECT 2.2uF 20% 100V C CERAMIC 0.001uF 10% 50V C CERAMIC 47PF 5% 50V C CERAMIC 470PF 10% 50V C ELECT 0.47uF 20% 50V C CERAMIC 47PF 5% 50V C CERAMIC 100PF 10% 50V C ELECT 2.2uF 20% 100V C ELECT 47uF 20% 25V C ELECT 47uF 20% 25V C CERAMIC 0.1uF 50V C FILM 0.1uF 5% 50V C FILM 0.1uF 5% 50V C ELECT 4700uF 20% 63V C ELECT 4700uF 20% 63V C ELECT 100uF 20% 35V C ELECT 47uF 20% 35V C ELECT 10uF 20% 50V C CERAMIC 0.01uF 30% 16V C ELECT 100uF 20% 16V C ELECT 47uF 20% 10V C ELECT 47uF 20% 10V C ELECT 10uF 20% 50V C ELECT 100uF 20% 16V C ELECT 47uF 20% 10V C ELECT 47uF 20% 10V C ELECT 47uF 20% 10V C ELECT 47uF 20% 10V C FILM 0.1uF 5% 50V C FILM 0.1uF 5% 50V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C ELECT 3300uF 20% 25V C ELECT 3300uF 20% 25V C FILM 0.82uF 5% 50V C FILM 0.82uF 5% 50V C ELECT 220uF 20% 10V C ELECT 100uF 20% 10V C ELECT 100uF 20% 10V C ELECT 2.2uF 20% 100V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC CHIP 220PF 10% 50V C CERAMIC CHIP 47PF 5% 50V C ELECT 4.7uF 20% 50V C ELECT 2.2uF 20% 100V C ELECT 4.7uF 20% 50V C ELECT 1000uF 20% 50V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C CERAMIC 0.01uF 30% 16V C CERAMIC 0.01uF 30% 16V C CERAMIC CHIP 47PF 5% 50V C ELECT 4.7uF 20% 50V C ELECT 2.2uF 20% 100V C ELECT 4.7uF 20% 50V C ELECT 1000uF 20% 50V C ELECT 220uF 20% 10V C FILM 0.033uF 5% 50V C FILM uF 5% 50V C FILM 0.033uF 5% 50V C ELECT 1uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C CERAMIC 0.001uF 10% 50V C ELECT 4.7uF 20% 50V C ELECT 2.2uF 20% 100V C CERAMIC CHIP 0.1uF 25V C CERAMIC CHIP 0.1uF 25V C ELECT 220uF 20% 10V C FILM 0.033uF 5% 50V C ELECT 10uF 20% 50V C ELECT 100uF 20% 10V C CERAMIC CHIP 680PF 10% 50V C ELECT 4.7uF 20% 50V C FILM 0.47uF 5% 50V C ELECT 47uF 20% 10V C FILM 0.1uF 5% 50V C FILM 0.1uF 5% 50V C ELECT 0.47uF 20% 50V C ELECT 4.7uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 4.7uF 20% 50V C FILM 0.15uF 5% 50V C ELECT 3.3uF 20% 50V 39

25 MAIN C FILM 0.15uF 5% 50V D DIODE RBV (TH) C FILM 0.022uF 5% 50V D DIODE UZ-33BSA C FILM 0.047uF 5% 50V D DIODE UZ-7.5BS (EXCEPT TH) C ELECT 220uF 20% 10V D DIODE RD7.5ESB2 (TH) C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C ELECT 220uF 20% 10V C ELECT 3.3uF 20% 50V C ELECT 3.3uF 20% 50V C FILM 0.1uF 5% 50V C FILM 0.1uF 5% 50V C ELECT 0.47uF 20% 50V C ELECT 4.7uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 4.7uF 20% 50V C FILM 0.15uF 5% 50V C ELECT 3.3uF 20% 50V C FILM 0.15uF 5% 50V C CERAMIC 0.1uF 50V < CONNECTOR > CN PIN, CONNECTOR 4P CN PIN, CONNECTOR (PC BOARD) 15P CN PLUG (MICRO CONNECTOR) 10P CN SOCKET, CONNECTOR(PC BOARD)18P CN SOCKET, CONNECTOR(PC BOARD)16P * CN PLUG, CONNECTOR 3P CN PLUG (MICRO CONNECTOR) 11P CN PLUG (MICRO CONNECTOR) 4P CN PIN, CONNECTOR 3P CN SOCKET, CONNECTOR 6P CNP CNP < CONNECTOR > SOCKET, CONNECTOR 17P (SYSTEM CONTROL 1) SOCKET, CONNECTOR 7P (SYSTEM CONTROL 2) D DIODE RD6.8ES-B3 D DIODE UZ-7.5BS (EXCEPT TH) D DIODE RD7.5ESB2 (TH) D DIODE 1N4148M D DIODE 1N4148M D DIODE 11ES2 D DIODE 11ES2 D DIODE 11ES2 D DIODE 11ES2 D DIODE 1S1585 D DIODE 11ES2 D DIODE 1N4148M D DIODE 1N4148M D DIODE 1N4148M D DIODE 1SS355 D DIODE 1S1585 < PLATE, GROUND > * E PLATE, GROUND < IC > IC IC upc4558g2 IC IC M62427FP IC IC MC14066BCP IC IC MC14052BCP IC IC M5218AP IC IC TA7812S IC IC NJM78M09FA IC IC upc1237ha IC IC upc4558g2 IC IC upc4558g2 IC IC TC9210P IC IC LV1011 IC IC LA2785 < DIODE > D DIODE 1N4148M D DIODE 1N4148M D DIODE 1N4148M D DIODE 11ES2 D DIODE 11ES2 D DIODE 1N4148M D DIODE 1N4148M D DIODE 1N4148M D DIODE 11ES2 D DIODE 11ES2 < JACK > J JACK,PHONE (PHONES) J JACK, PIN 4P (MD IN/OUT) J JACK,PHONE (MIC MIX) < JUMPER RESISTOR > JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 10K 5% 1/10W D DIODE RBV-602 (EXCEPT TH) 40

26 MAIN < COIL > R METAL CHIP 2.2K 5% 1/10W R METAL GLAZE 1K 5% 1/10W L COIL, AIR-CORE R METAL GLAZE 100K 5% 1/10W L COIL, AIR-CORE R METAL GLAZE 1K 5% 1/10W L INDUCTOR 10uH (EXCEPT TH) (EXCEPT TH) L INDUCTOR 10uH < TRANSISTOR > Q TRANSISTOR 2SC403SP-51 Q TRANSISTOR 2SC403SP-51 Q TRANSISTOR FN1A4M-M33 Q TRANSISTOR 2SC3624-L18 Q TRANSISTOR 2SC3624-L18 Q TRANSISTOR 2SC1623-L5L6 Q TRANSISTOR 2SC1623-L5L6 Q TRANSISTOR FN1A4M-M33 Q TRANSISTOR FN1A4M-M33 Q TRANSISTOR 2SD1387 Q TRANSISTOR 2SD1387 Q TRANSISTOR 2SC3624A-L15 Q TRANSISTOR FN1A4M-M33 Q TRANSISTOR 2SC3624A-L15 Q TRANSISTOR 2SC3398 (EXCEPT TH) Q TRANSISTOR RT1N141C-TP-1 (TH) Q TRANSISTOR 2SB1094-LK Q TRANSISTOR 2SD2012 Q TRANSISTOR 2SD2012 Q TRANSISTOR 2SB1094-LK Q TRANSISTOR RT1N141SK-TP Q TRANSISTOR 2SC2603-EF Q TRANSISTOR RT1N441SK-TP Q TRANSISTOR DTA124EK Q TRANSISTOR 2SC3624-L18 Q TRANSISTOR 2SC3623A-LK Q TRANSISTOR 2SC3624-L18 Q TRANSISTOR 2SC3624-L18 Q TRANSISTOR 2SC2603-EF < RESISTOR > R METAL CHIP 10K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R CARBON 1.5K 5% 1/4W (US,CND) R CARBON 1K 5% 1/4W R CARBON 1.5K 5% 1/4W (US,CND) R CARBON 1K 5% 1/4W R CARBON 220K 5% 1/4W R METAL CHIP 4.7K 5% 1/10W (TH) R METAL CHIP 33K 5% 1/10W R CARBON 100K 5% 1/4W R CARBON 10K 5% 1/4W R METAL CHIP 4.7K 5% 1/10W R METAL GLAZE 1M 5% 1/10W R CARBON 220 5% 1/4W R CARBON 22K 5% 1/4W R CARBON 47K 5% 1/4W R METAL GLAZE 100 5% 1/10W R METAL CHIP 150K 5% 1/10W R METAL GLAZE 220K 5% 1/10W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1.5K 5% 1/4W (US,CND) R CARBON 1K 5% 1/4W R CARBON 1.5K 5% 1/4W (US,CND) R CARBON 1K 5% 1/4W R CARBON 220K 5% 1/4W R METAL CHIP 2.2K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R CARBON 100K 5% 1/4W R METAL GLAZE 1K 5% 1/10W (EXCEPT TH) 41

27 MAIN R METAL CHIP 4.7K 5% 1/10W R METAL CHIP 6.8K 5% 1/10W (TH) R METAL CHIP 33K 5% 1/10W R METAL CHIP 10K 5% 1/10W R CARBON 100K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 100 5% 1/4W R METAL GLAZE 100K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R CARBON 10K 5% 1/4W R METAL CHIP 150K 5% 1/10W R METAL CHIP 4.7K 5% 1/10W R CARBON 22K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R METAL GLAZE 100K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R CARBON 4.7K 5% 1/4W R METAL GLAZE 1K 5% 1/10W R METAL GLAZE 100 5% 1/10W R METAL CHIP 4.7K 5% 1/10W R METAL GLAZE 100 5% 1/10W R CARBON 4.7K 5% 1/4W R METAL CHIP 4.7K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL CHIP 10K 5% 1/10W R CARBON 10K 5% 1/4W R METAL CHIP 18K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R CARBON 100K 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 18K 5% 1/4W R METAL CHIP 3.3K 5% 1/10W (US,CND) R METAL CHIP 6.8K 5% 1/10W R METAL GLAZE 220K 5% 1/10W R METAL CHIP 5.6K 5% 1/10W (US,CND) R METAL CHIP 6.8K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R METAL GLAZE 100K 5% 1/10W R METAL CHIP 10K 5% 1/10W R CARBON 1K 5% 1/4W R CARBON 100K 5% 1/4W R METAL CHIP 3.3K 5% 1/10W (US,CND) R METAL CHIP 6.8K 5% 1/10W R METAL GLAZE 220K 5% 1/10W R METAL CHIP 5.6K 5% 1/10W (US,CND) R METAL CHIP 10K 5% 1/10W R CARBON 1K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 100 5% 1/4W! R FUSIBLE 100 5% 1/2W F R CARBON 1K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 1K 5% 1/4W! R FUSIBLE 6.8 5% 1/4W F R CARBON 1K 5% 1/4W! R FUSIBLE 1 5% 1/2W F! R FUSIBLE 6.8 5% 1/4W F! R FUSIBLE 1 5% 1/2W F! R FUSIBLE 3.3 5% 1/2W F R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 22 5% 1/4W R METAL GLAZE 100K 5% 1/10W R METAL CHIP 10K 5% 1/10W R CARBON 33K 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 68K 5% 1/4W R CARBON 4.7K 5% 1/4W R METAL OXIDE 1.2K 5% 2W (US,CND) R METAL OXIDE 820 5% 2W R METAL CHIP 10K 5% 1/10W R METAL CHIP 6.8K 5% 1/10W (US,CND) R METAL CHIP 10K 5% 1/10W R CARBON 22 5% 1/4W R CARBON 22 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 22 5% 1/4W R CARBON 22 5% 1/4W R METAL CHIP 10K 5% 1/10W R METAL CHIP 10K 5% 1/10W The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 42

28 MAIN PANEL JOY ENCODER VOL ENCODER R CARBON 3.3K 5% 1/4W R CARBON 100K 5% 1/4W R METAL CHIP 10K 5% 1/10W R CARBON 100K 5% 1/4W R METAL GLAZE 4.7K 5% 1/10W R CARBON 10K 5% 1/4W (E2,AUS) R METAL GLAZE 1K 5% 1/10W R METAL CHIP 4.7K 5% 1/10W < VARIABLE RESISTOR > R METAL GLAZE 100K 5% 1/10W R METAL CHIP 4.7K 5% 1/10W RV RES, VAR, CARBON 10K (MIC LEVEL) R METAL GLAZE 1K 5% 1/10W < RELAY > R METAL GLAZE 47K 5% 1/10W R CARBON 47K 5% 1/4W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R CARBON 100K 5% 1/4W RY RELAY (24V) RY RELAY (24V) < TERMINAL > R METAL CHIP 15K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL GLAZE 100K 5% 1/10W R CARBON 1K 5% 1/4W R CARBON 4.7K 5% 1/4W R METAL GLAZE 1K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R CARBON 220 5% 1/4W R CARBON 220 5% 1/4W R METAL OXIDE 1.2K 5% 2W (US,CND) R METAL OXIDE 820 5% 2W R METAL GLAZE 1K 5% 1/10W R METAL GLAZE 100K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL GLAZE 100K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R METAL CHIP 4.7K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R CARBON 220 5% 1/4W R CARBON 220 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 1M 5% 1/4W R CARBON 330 5% 1/4W R CARBON 18K 5% 1/4W R METAL CHIP 39K 0.5% 1/10W R METAL CHIP 39K 0.5% 1/10W R CARBON 1K 5% 1/4W R METAL GLAZE 1K 5% 1/10W R METAL GLAZE 1K 5% 1/10W R CARBON 1K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 100 5% 1/4W TB TERMINAL BOARD (CHECKER PIN) (FRONT SPEAKER) < VIBRATOR > X VIBRATOR, CERAMIC (8MHz) ************************************************************ * A A PANEL BOARD, COMPLETE (US,CND) * A A PANEL BOARD, COMPLETE (E3,EA,MY,SP,HK) * A A PANEL BOARD, COMPLETE (E2) * A A PANEL BOARD, COMPLETE (AR) * A A PANEL BOARD, COMPLETE (AUS) * A A PANEL BOARD, COMPLETE (JE) A A PANEL BOARD, COMPLETE (TH) ********************** JOY ENCODER BOARD ****************** VOL ENCODER BOARD ****************** * CUSHION (FL) * HOLDER, FL TUBE * HOUSE, LAMP < CAPACITOR > C CAPACITOR 0.22uF 5.5V C CERAMIC CHIP 0.01uF 10% 50V C CERAMIC 0.1uF 50V C CERAMIC 0.1uF 50V C ELECT 100uF 20% 35V C ELECT 100uF 20% 6.3V C CERAMIC 0.1uF 50V C ELECT 22uF 20% 50V C CERAMIC 0.1uF 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 18PF 5% 50V C CERAMIC 0.1uF 50V C CERAMIC 0.047uF 50V C ELECT 0.22uF 20% 50V C CERAMIC 0.01uF 50V C MYLAR uF 5% 50V 43

29 PANEL JOY ENCODER VOL ENCODER C FILM 0.015uF 5% 50V D DIODE 11ES2 C CERAMIC CHIP uF 10% 100V D DIODE 1N4148M C CERAMIC CHIP 330PF 10% 50V D DIODE 1N4148M C CERAMIC CHIP 0.01uF 50V C ELECT 10uF 20% 50V C ELECT 0.1uF 20% 50V C CERAMIC CHIP 0.1uF 25V C CERAMIC CHIP 0.1uF 25V C CERAMIC CHIP 0.1uF 25V < CONNECTOR > CN PLUG, CONNECTOR (PC BOARD) 18P CN PLUG, CONNECTOR (PC BOARD) 16P D DIODE 1N4148M D DIODE 1N4148M D DIODE 1N4148M D DIODE UZ-6.8BS (EXCEPT TH) D DIODE UZ-6.8BS-TA (TH) D DIODE 1N4148M D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS355 < DIODE > D LED SEL4214R-D-TP (3CH LOGIC) D LED SEL4214R-D-TP (PHANTOM) D LED SEL4214R-D-TP (NORMAL) D DIODE UZP-5.6BC-TP D LED SEL5821A-TH15 (=) D LED SEL5821A-TH15 (+) D LED SEL5821A-TH15 ( + ) D LED SEL5821A-TH15 ( ) D LED TLO124 (ENTER/NEXT) D LED TLO124 (EFFECT ON/OFF) D LED SEL5421E-TP15 (TUNER/BAND) D LED SEL5821A-TH15 (TUNER) D LED SEL5821A-TH15 (EFFECT) D LED SEL1810D-TP3 (TIMER SET) D LED HLMF-K405-2UP (REPEAT) D LED HLMF-K405-2UP (CD MUSIC CLIP A) D LED HLMF-K405-2UP (CD MUSIC CLIP C) D LED HLMF-K405-2UP (CLIP ERASE) D LED HLMF-K405-2UP (CLIP ERASE) D LED HLMF-K405-2UP (1/ALL DISCS) D LED HLMF-K405-2UP (1/ALL DISCS) D LED SEL5821A-TH15 (TIMER) D LED SEL5821A-TH15 (c) D LED SEL5821A-TH15 (C) D LED SEL5421E-TH8F (TIMER) D LED SEL5821A-TH15 (GROOVE) D LED SEL1810D-TP3 (TUNER MEMORY) D LED SEL1810D-TP3 (TUNING MODE) D LED SEL1810D-TP3 (CLOCK STEP) D LED SEL1810D-TP3 (TIMER SELECT) D LED SEL5821A-TH15 (CD) D LED HLMF-K405-2UP (CD MUSIC CLIP B) D LED HLMF-K405-2UP (CLIP PLAY) D LED HLMF-K405-2UP (CLIP PLAY) D LED HLMF-K405-2UP (EDIT) D LED HLMF-K405-2UP (PLAY MODE) D LED HLMF-K405-2UP (PLAY MODE) D DIODE 1N4148M D LED SEL5821A-TH15 (CENTER MODE) D LED SEL5821A-TH15 (CENTER MODE) D LED SEL5821A-TH15 (CENTER MODE) D LED SEL5821A-TH15 (CENTER MODE) D LED SEL5821A-TH15 (CENTER MODE) < FILTER > FL INDICATOR TUBE, FLUORESCENT < IC > IC IC ASD0205GF-015-3BA IC IC GP1U27XB IC IC PST600E-T IC IC M66313FP-200C < JUMPER RESISTOR > JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W 44

30 PANEL JOY ENCODER VOL ENCODER JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/10W JR METAL CHIP 0 5% 1/8W JR METAL CHIP 0 5% 1/8W < LEAD, JUMPER > * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) * JW LEAD, JUMPER (OFC) (EXCEPT TH) < COIL > L INDUCTOR 10uH L INDUCTOR 10uH < TRANSISTOR > Q TRANSISTOR 2SC2603-EF Q TRANSISTOR 2SC2603-EF Q TRANSISTOR UN2211 Q TRANSISTOR UN2211 Q TRANSISTOR UN2211 Q TRANSISTOR UN2211 Q TRANSISTOR RT1P141SK-TP Q TRANSISTOR 2SB1116 Q TRANSISTOR 2SB1116 < RESISTOR > R CARBON 150 5% 1/4W R METAL CHIP 150 5% 1/10W R CARBON 150 5% 1/4W R CARBON 47 5% 1/4W R CARBON 68 5% 1/4W R CARBON 68 5% 1/4W R CARBON 100 5% 1/4W R CARBON 150 5% 1/4W R CARBON 220 5% 1/4W R CARBON 330 5% 1/4W R CARBON 330 5% 1/4W R CARBON 470 5% 1/4W R CARBON 680 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 1.5K 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 6.8K 5% 1/4W R CARBON 47 5% 1/4W R CARBON 68 5% 1/4W 45

31 PANEL JOY ENCODER VOL ENCODER R CARBON 68 5% 1/4W R METAL GLAZE 100 5% 1/10W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 150 5% 1/4W R CARBON 100 5% 1/4W R CARBON 220 5% 1/4W R METAL CHIP 330 5% 1/10W R METAL CHIP 330 5% 1/10W R METAL CHIP 470 5% 1/10W R METAL CHIP 680 5% 1/10W R METAL GLAZE 1K 5% 1/10W R METAL CHIP 1.5K 5% 1/10W R METAL CHIP 2.2K 5% 1/10W R METAL CHIP 3.3K 5% 1/10W R CARBON 22 5% 1/4W R CARBON 22 5% 1/4W R CARBON 100 5% 1/4W R CARBON 47 5% 1/4W R CARBON 68 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 22K 5% 1/4W R CARBON 15 5% 1/4W R CARBON 33 5% 1/4W R CARBON 15 5% 1/4W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL CHIP 22 5% 1/10W R METAL CHIP 22 5% 1/10W R METAL GLAZE 68 5% 1/8W R CARBON 22 5% 1/4W R CARBON 68 5% 1/4W R CARBON 68 5% 1/4W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL GLAZE 68 5% 1/8W R METAL CHIP 22 5% 1/10W R METAL GLAZE 68 5% 1/8W R METAL CHIP 22 5% 1/10W R CARBON 4.7K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R METAL GLAZE 100 5% 1/10W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R METAL GLAZE 100 5% 1/8W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R METAL CHIP 33K 5% 1/10W R METAL CHIP 33K 5% 1/10W R METAL CHIP 33K 5% 1/10W R METAL CHIP 10K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 47K 5% 1/10W R METAL GLAZE 1M 5% 1/10W R METAL GLAZE 1M 5% 1/10W R METAL GLAZE 1M 5% 1/10W R METAL GLAZE 1M 5% 1/10W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R METAL CHIP 10K 5% 1/10W R METAL GLAZE 10K 5% 1/8W R CARBON 100K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 6.8K 5% 1/4W (E3,EA,MY,SP,HK) R CARBON 22K 5% 1/4W (TH) R CARBON 3.3K 5% 1/4W (AUS) R CARBON 680 5% 1/4W (JE) R CARBON 10K 5% 1/4W (E2,AUS) R CARBON 33K 5% 1/4W (E3,EA,MY,SP,HK) R CARBON 6.8K 5% 1/4W (AR) 46