ELECTRICAL RISER & DISTRIBUTION. Co-X/FMD/SOP06
|
|
- Bathsheba Carpenter
- 5 years ago
- Views:
Transcription
1 CONVENTION & EXHIBITION (PUTRAJAYA) SDN. BHD. Co-X/FMD/SOP06 Revision No.: 01 Effective Date: 15 th December 2017 PREPARED BY REVIEWED BY APPROVED BY Name: Name: Name: Designation: Designation: Designation:
2 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 2 of 9 REVISION HISTORY Rev. No DCN No. Description of Changes Effective Date Initial Release 15/12/17
3 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 3 of OBJECTIVE The objective of this procedure is to provide guidelines on preventive maintenance for electrical riser and distribution. 2.0 SCOPE This procedure shall be applicable for all electrical riser distribution inside Putrajaya International Convention Centre (PICC) building. 3.0 DEFINITION 3.1 Co-X : Convention & Exhibition (Putrajaya) Sdn. Bhd. 3.2 PICC : Putrajaya International Convention Centre 3.3 SSB : Sub Switch Board 3.4 DB : Distribution Board 3.5 DC : Document Controller 3.6 MCCB : Molded Case Circuit Breaker 3.7 MCB : Miniature Circuit Breaker 3.8 ELCB : Earth-leakage circuit breaker 3.9 ELR : Earth-Leakage Relay 3.10 OCR : Overcurrent Relay 3.11 ST : Suruhanjaya Tenaga 4.0 RESPONSIBILITY 4.1 The DC shall oversee all documents and records are properly managed at all times. 4.2 Chargeman is responsible to prepare and arrange all electrical riser preventive maintenance frequency, schedule and verify technician work. 4.3 Technician is responsible to perform the preventive maintenance as per schedule or task for all electrical riser inside PICC. 5.0 REFERENCE 5.1 Safety Work Procedure Guide For Electrical Work by ST 5.2 Co-X/FMD/SOP01 Preventive Maintenance & Equipment Management 5.3 Co-X/FMD/SOP05 Main Electrical System
4 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 4 of PROCEDURE 6.1 Electrical Riser In General Tap-off Unit function to receive / cut-off electrical supply (415V) at every level from LV system (refer Co-X/FMD/SOP05) before distributed to SSB. Riser Room Riser room Tap-off unit
5 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 5 of SSB then distribute the power to DB with safety protection equipment as below: Earth-Leakage Relay (ELR) Overcurrent Relay (OCR) Molded Case Circuit Breaker (MCCB) Phase indicator (Red Yellow Blue) Molded Case Circuit Breaker (MCCB) 100A Molded Case Circuit Breaker (MCCB) 63A Molded Case Circuit Breaker (MCCB) 32A Sub Switch Board (SSB) Earthleakage relay Phase indicator
6 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 6 of 9 MCCB for incoming supply MCCB for distribution supply DB then distribute electrical supply to end user / building electrical load Molded Case Circuit Breaker (MCCB) Earth Leakage Circuit Breaker (ELCB) Miniature Circuit Breaker (MCB) Overcurrent fuse Miniature Circuit Breaker (MCB) 10A Miniature Circuit Breaker (MCB) 20A Miniature Circuit Breaker (MCB) 32A Distribution Board (DB)
7 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 7 of 9 Overcurrent fuse ELCB ELCB bypass switch MCCB for incoming supply MCB for distribution supply 6.2 Plan Preventive Maintenance PPM for Distribution System frequency as per Plan Preventive Maintenance (PPM) Schedule (Co-X/FMD/SOP01-R03) Safety precautions / general guidelines prior to carry out PPM: Please ensure the safety of all technicians by following safety rules, regulations and PPE (helmet, safety shoes, rubber glove, safety glasses etc.) The PPM shall be carried out by competent person level PW4 and above Display of safety signage during maintenance activities Physical check at SSB / DB panel by visual internally and externally. Ensure panel board has no defect and in good condition Physical check of any burn marks at all terminals inside the panel and re-tightening all cables termination point if needed Checking point to point for any bad contact at respective panel by using test equipment (e.g. Multi-meter) Perform functionality tripping test to ensure all circuits still intact for: MCCB RCD / ELCB MCB Conduct housekeeping of electrical riser room panels and the surrounding.
8 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 8 of All findings will be recorded on Electrical Riser Checklist (Co-X/FMD/SOP01-R08(g)) Any non-compliance finding during PPM then shall be forwarded to Unplanned Maintenance Procedure (Co-X/FMD/SOP01). 7.0 RECORDS 7.1 Co-X/FMD/SOP01-R03 Plan Preventive Maintenance (PPM) Schedule 7.2 Co-X/FMD/SOP01-R08(g) Electrical Riser Checklist 8.0 APPENDIX / ATTACHMENT 8.1 Process Flow
9 REFERENCE NO. Co-X/FMD/SOP06 PAGE NO. Page 9 of 9 PROCESS FLOW RESPONSIBILITY OUTLINE ACTION 1 Main Electrical System - Co-X/FMD/SOP05 - Technician with minimum competency level PW4 2 Tap-Off Unit - Receive / cut-off electrical supply at every level - Technician with minimum competency level PW4 3 SSB - Distribute electrical supply to DB c/w safety protection - Technician with minimum competency level PW1 (monitored by PW4) 4 DB - Distribute electrical supply to end-load / end user - End user 5 Load / end user - Electrical supply user
Licensed Electricians Practical Assessment (LEP)
Licensed Electricians Practical Assessment (LEP) Surname: Given Names: Date: Time: Location: Assessment Time (includes reading and preparation time): At the end of this time you will be asked to stop.
More informationLicensed Electricians Practical Assessment (LEP)
Licensed Electricians Practical Assessment (LEP) Surname: Date: Given Names: Time: Assessment Time (includes 10 minutes reading time): At the end of this time you will be asked to stop. 4 hours Have you
More informationPROJECT: SUPPLY & INSTALL ELECTRICAL SWITCHBOARD AT SENGKURONG EXCHANGE PHASE 1, JLN TUTONG, BSB. SCOPE OF WORK The scope of work under Electrical Services shall include but not limited to the supply,
More informationElectrical Switchgear & Power Transformer Testing. H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E
Electrical Switchgear & Power Transformer Testing H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E www.ictd.ae ictd@ictd.ae Course Introduction: This will provide you with practical knowledge
More information, Power Industries and Communications Industry Training Board
, Power Industries and Communications Industry Training Board Suite 3 Level 22185 187 Boundary Boundary Rd Rd North Melbourne VIC 3051 Phone VIC 3051 (03) 9654 1299 Phone (03) 9654 1299 Facsimile (03)
More informationBiomedical Equipment Technician
Biomedical Equipment Technician Occupational Skill Stards Texas Skill Stards Board Recognized Critical Work Function 1. Install Biomedical Equipment 1.1 Receive, inspect inventory upon delivery 1.2 Deliver
More informationSubstation Preventive Maintenance
Substation Preventive Maintenance PROVINCIAL ELECTRICITY AUTHORITY 1 Presentation Contents 1) A kind of substation 2) Electrical equipment details of AIS substation 3) Electrical equipment details of GIS
More informationSubstation: From the Outside Looking In.
1 Substation: From the Outside Looking In. Moderator n Ron Spataro AVO Training Institute Marketing Manager 2 Q&A n Send us your questions and comments during the presentation 3 Today s Presenter n Greg
More informationElectrical Protection System Design and Operation
ELEC9713 Industrial and Commercial Power Systems Electrical Protection System Design and Operation 1. Function of Electrical Protection Systems The three primary aims of overcurrent electrical protection
More informationBIRD ISLAND FLATS SUBSTATION (BUILDING 67) ONE LINE DIAGRAM SET# 23 LEGEND DRAW-OUT CIRCUIT BREAKER DRAW-OUT CIRCUIT BREAKER, DRAW-OUT FUSES DRAW-OUT FUSES AND POTENTIAL TRANSFORMERS CABLE CONNECTION POTENTIAL
More informationUNITY/I TM. Installation Manual. UT3K, UT4K, UT5K and UT8K. Single-Phase Uninterruptible Power Systems
UNITY/I TM UT3K, UT4K, UT5K and UT8K Single-Phase Uninterruptible Power Systems Installation Manual MLS-0351C-OL Copyright 1994-1997 Best Power. All rights reserved. å IMPORTANT SAFETY INSTRUCTIONS! SAVE
More informationBritish Columbia Institute of Technology WOOD DUST EXPOSURE CONTROL PLAN (CARPENTRY)
WOOD DUST EXPOSURE CONTROL PLAN (CARPENTRY) Contents 1. Purpose... 3 2. Roles & Responsibilities... 3 2.1 Supervisor/Instructor... 3 2.2 Chief Instructor... 3 2.3 Facilities Maintenance... 4 2.4 Housekeeping...
More informationArc Flash Analysis Training
Arc Flash Analysis Training Contact us Today for a FREE quotation to deliver this course at your company?s location. https://www.electricityforum.com/onsite-training-rfq An arc flash analysis study is
More informationAN EXAMPLE OF A STANDARD ARC FLASH PPE LABELING STRATEGY
The Electrical Power Engineers Qual-Tech Engineers, Inc. 201 Johnson Road Building #1 Suite 203 Houston, PA 15342-1300 Phone 724-873-9275 Fax 724-873-8910 www.qualtecheng.com AN EXAMPLE OF A STANDARD ARC
More informationSignal Integrity Test Report
PD-0098 Signal Integrity Test Report 3M External MiniSAS Cable Assemblies 3 Electronic Solutions Division Subject: 3M External MiniSAS Cable Assembly Page: 1 of 14 Table of Contents 1.0 Scope... 2 2.0
More informationPROTECTION of electricity distribution networks
PROTECTION of electricity distribution networks Juan M. Gers and Edward J. Holmes The Institution of Electrical Engineers Contents Preface and acknowledgments x 1 Introduction 1 1.1 Basic principles of
More informationTN, TT & IT Earthing Arrangements
TN, TT & IT Earthing Arrangements In IT and TN-C networks, residual current devices are far less likely to detect an insulation fault. In a TN-C system, they would also be very vulnerable to unwanted triggering
More informationNFPA-70E. Electrical Safety in the Workplace. Standard for Edition
NFPA-70E Standard for Electrical Safety in the Workplace 2015 Edition NFPA-70E 90.1 Purpose. The purpose of this standard is to provide a practical safe working area for employees relative to the hazards
More informationC&G Level 3 Award in the Periodic Inspection, Testing and Certification of Electrical Installations. Earth Fault Loop Impedance Tests
C&G 2395-01 Level 3 Award in the Periodic Inspection, Testing and Certification of Electrical Installations Earth Fault Loop Impedance Tests 1 Revision Inspections are made to verify that the installed
More informationVoltage Relays. Ensuring Reliable Protection for Electrical Systems against Voltage Faults. ISO 9001:2008 Certified.
Ensuring Reliable Protection for Electrical Systems against Voltage Faults Voltage Relays Inside the Catalogue Range Model Selection Specifications Technical Terms & Data ISO 9001:2008 Certified Delivering
More informationGreenlining and Bluelining of Ergon Energy Substation Drawings
Greenlining and Bluelining of Ergon Energy Table of Contents Purpose and Scope... 1 Responsibilities... 1 Definitions, Abbreviations and Acronyms... 1 References... 1 General... 1 Requirements... 3 Testing
More informationSECTION PANELBOARDS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 24 16 PANELBOARDS SPEC WRITER NOTE: Delete between // --- // if not applicable to project. Also, delete any other item or paragraph not applicable in the section
More informationTrusted Power Distribution Unit MCB 24 Vdc
PD-T8292 Trusted Trusted Power Distribution Unit MCB 24 Vdc Product Overview The dual 5-channel Trusted Power Distribution Unit Miniature Circuit Breaker (MCB) 24 V is designed for N+1 or 100 % redundant
More informationMV, HV AND EHV SWITCHGEAR TESTING & COMMISSIONING
Training Title MV, HV AND EHV SWITCHGEAR TESTING & COMMISSIONING Training Duration 5 days Training Date MV, HV and EHV Switchgear Testing & Commissioning 5 21 25 Sep $3,750 Dubai, UAE In any of the 5 star
More informationTABLE OF CONTENT
Page : 1 of 34 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT SCOPE 3 REFERENCES
More informationECP GROUND-MOUNTED SWITCHGEAR WITH PROTECTION RELAYS COMMISSIONING PROCEDURE
ENGINEERING COMMISSIONING PROCEDURE ECP 11-0512 GROUND-MOUNTED SWITCHGEAR WITH PROTECTION RELAYS COMMISSIONING PROCEDURE Network(s): Summary: EPN, LPN, SPN This procedure details the testing and commissioning
More informationCapstone Turbine Corporation Nordhoff Street Chatsworth CA USA Phone: (818) Fax: (818) Web:
Phone: (818) 734-5300 Fax: (818) 734-5320 Web: www.capstoneturbine.com Technical Reference Capstone MicroTurbine Electrical Installation 410009 Rev F (October 2013) Page 1 of 31 Capstone Turbine Corporation
More informationSample Slip and Fall Prevention Program
Slip and Fall Prevention Program United Heartland has developed this sample Slip, Trip and Fall (STF) prevention program to assist our customers as they develop their own program. It shares best practices
More informationSAFETY AND HEALTH STANDARD ELECTRICAL GROUNDING Effective Date: 07/17/10 Standard: Document Number: KUCSH0039 Rev: 4
SAFETY AND HEALTH STANDARD ELECTRICAL GROUNDING Effective Date: 07/17/10 Standard: 16.10 Document Number: KUCSH0039 Rev: 4 16.10.1 INTRODUCTION 16.10.1.1 The intent of this standard is to ensure that continuity
More informationECP GROUND-MOUNTED SWITCHGEAR COMMISSIONING PROCEDURE
Document Number: ECP 11-0511 Network(s): Summary: ENGINEERING COMMISSIONING PROCEDURE ECP 11-0511 GROUND-MOUNTED SWITCHGEAR COMMISSIONING PROCEDURE EPN, LPN, SPN This procedure details the testing and
More informationET 51 - Electrician Theory Examination Marking Schedule
ET 51 - Electrician Theory Examination Marking Schedule Notes:1. means that the preceding statement/answer earns 1 mark. 2. This schedule sets out the accepted answers to the examination questions. A marker
More informationModel Curriculum. Assistant Electrician (NSQF Level 3) SECTOR: SUB-SECTOR:
Model Curriculum Assistant Electrician (NSQF Level 3) SECTOR: SUB-SECTOR: OCCUPATION: REF. ID: NSQF LEVEL: CONSTRUCTION REAL ESTATE AND INFRASTRUCTURE CONSTRUCTION CONSTRUCTION ELECTRICAL WORKS CON/Q0602
More informationNATIONAL RULES FOR ELECTRICAL INSTALLATIONS. Fourth Edition. Extracts from Amendment No.1: June 2011
NATIONAL RULES FOR ELECTRICAL INSTALLATIONS Fourth Edition ET 101:2008 Extracts from Amendment No.1:2011 22 June 2011 Page vi: Insert after 1 st Paragraph: Section 710: Medical Locations was prepared by
More informationER 87 Electrician Regulations Answer Schedule. Question 1 Marks Reference Marking notes. (1 mark) ESR 27(2) (2 marks) ESR 74A(1AA)
ER 87 Electrician Regulations Answer Schedule Notes:1. (1 mark) means that the preceding statement/answer earns 1 mark. 2. This schedule sets out the expected answers to the examination questions. The
More informationPRE COMMISSIONING TESTS ON EQUIPMENT AT 33/11 KV SUB STATIONS. IR Values are to be read on the megger by meggering the Power transformer
PRE COMMISSIONING TESTS ON EQUIPMENT AT 33/11 KV SUB STATIONS TESTS ON TRANSFORMERS 1. IR Values This is measured to measure the Insulation Resistance of the whole transformer. a) For 33/11 KV Power Transformer
More informationSection L5: PRE-ENERGIZATION TEST PROCEDURES FOR LOAD-ONLY ENTITIES AND TRANSMISSION-ONLY ENTITIES
Section L5: PRE-ENERGIZATION TEST PROCEDURES FOR LOAD-ONLY ENTITIES AND TRANSMISSION-ONLY ENTITIES PURPOSE The following is PG&E's procedure for pre-energization inspections. For PG&E to provide the Load
More informationElectrical Procedure No E032. Procedure No: ELE 032
Procedure No: ELE 032 Procedure Title: Date of Procedure: Responsible Person(s) Safety Isolation of Low Voltage Networks and Systems for work to be carried out by third parties. i.e. Non University personnel.
More informationPre-Installation Guide
Getting Started Pre-Installation Guide This guide helps you determine how many Ohm hardware units are needed to monitor your space as well as provide safety information and installation checklists. Only
More informationAN EXAMPLE OF A STANDARD ARC FLASH PPE LABELING STRATEGY
The Electrical Power Engineers Qual-Tech Engineers, Inc. 201 Johnson Road Building #1 Suite 203 Houston, PA 15342-1300 Phone 724-873-9275 Fax 724-873-8910 www.qualtecheng.com AN EXAMPLE OF A STANDARD ARC
More informationLV/MV/HV CIRCUIT BREAKERS (SWITCH GEAR) DESIGN, INSPECTION, MAINTENANCE, REPAIR & TROUBLESHOOTING
Training Title LV/MV/HV CIRCUIT BREAKERS (SWITCH GEAR) DESIGN, INSPECTION, MAINTENANCE, REPAIR & TROUBLESHOOTING Training Duration 5 days Training Venue and Dates LV/MV/HV Circuit Breakers (Switchgear):
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More informationElectrical Safety Policy Health and Safety FCX-HS03 Release 07/2018 Version 1
Electrical Safety Policy Health and Safety FCX-HS03 Release 07/2018 Version 1 POTENTIAL FATAL RISKS Exposure to Electrical Hazards CRITICAL CONTROLS Access Control Barriers and Segregation Electrical PPE
More informationFR-ABR-(H)0.4K to 22K
TRANSISTORIZED INVERTER INSTRUCTION MANUAL HIGH-DUTY BRAKE RESISTOR FR-ABR-(H)0.4K to 22K H Thank you for choosing the Mitsubishi transistorized inverter option unit. This instruction manual gives handling
More informationNIRAPOD 1. High performance circuit breaker mcb and combined mcb with remote controls. LV Distribution Products 2-63A
High performance circuit breaker mcb and combined mcb with remote controls LV Distribution Products 2-63A Mini motorized circuit breaker The mini-series of motorized circuit breakers operates both locally
More informationVIP ESI. Electrical Service Industry Voltage and Impedance Indicator. Instruction Manual & Specification
VIP ESI Electrical Service Industry Voltage and Impedance Indicator Instruction Manual & Specification Issue1. 01/16 1 SnS004v1 1. Safety 1.1 Equipment Markings Caution - refer to this instruction manual
More informationCOOPER POWER SERIES. External application of a motor start capacitor on a single-phase voltage regulator. Voltage Regulators MN225063EN
Voltage Regulators MN225063EN Effective March 2017 Supersedes January 2012 (S225-60-10) COOPER POWER External application of a motor start capacitor on a single-phase voltage regulator SERIES DISCLAIMER
More informationWARNING: DO NOT PROCEED WITHOUT READING THIS PAGE.
WARNING: DO NOT PROCEED WITHOUT READING THIS PAGE. The B-1030-G produces at least 300 watts of VHF R.F. power and is not to be taken lightly. Severe R.W. burns can be sustained at this power level! Power
More information4. CONNECTIONS. Make sure all connections to and in your Universal Rectifier are tight.
OPERATING AND MAINTENANCE INSTRUCTIONS FOR CONSTANT CURRENT RECTIFIERS USING SATURABLE CORE REACTORS I. WARNING Operating personnel should observe the following before attempting to operate or adjust the
More informationConstruction Measurement III SBQ3314. Electrical Installations : Single & Three Phase. Dr. Sarajul Fikri Mohamed
Construction Measurement III SBQ3314 Electrical Installations : Single & Three Phase Dr. Sarajul Fikri Mohamed Table of contents 1. Electrical installations: main components 2. SMM2 measurement rules for
More informationEmbedded Generation Connection Application Form
Embedded Generation Connection Application Form This Application Form provides information required for an initial assessment of the Embedded Generation project. All applicable sections must be completed
More information201AP Charge Amplifier User Manual
Trig-Tek 201AP Charge Amplifier User Manual Publication No. 980996 Rev. A Astronics Test Systems Inc. 4 Goodyear, Irvine, CA 92618 Tel: (800) 722-2528, (949) 859-8999; Fax: (949) 859-7139 atsinfo@astronics.com
More informationEarthing, HV Switching and Associated Operational Equipment. Approval: Chief Operating Officer
ACCESS PRACTICE AP 24 Earthing, HV Switching and Associated Operational Equipment Process Authority: Manager Operations Improvement Approval: Chief Operating Officer Version Date: 27/08/2013 Revision:
More informationC&G Level 3 Award in the Periodic Inspection, Testing and Certification of Electrical Installations
C&G 2395-01 Level 3 Award in the Periodic Inspection, Testing and Certification of Electrical Installations Phase rotation and verification of voltage drop 1 Outcomes of this Session describe how to assess
More informationMirage B-320-G FEATURES
Mirage B-320-G The Mirage B-320-G is a VHF power amplifier designed for 2 meters covering 144-148 MHz. The Hi and Lo input selector switch makes this amp useable for both handheld and mobile transceivers.
More informationWARNING: DO NOT PROCEED WITHOUT READING THIS PAGE.
WARNING: DO NOT PROCEED WITHOUT READING THIS PAGE. The B-2530-G produces at least 300 watts of VHF R.F. power and is not to be taken lightly. Severe R.W. burns can be sustained at this power level! Power
More information# - - Internal * On Line Examination
COURSE NAME : ELECTRICAL ENGINEERING GROUP COURSE CODE : EE/EP SEMESTER : FIFTH SUBJECT TITLE : SWITCHGEAR and PROTECTION SUBJECT CODE : Teaching and Examination Scheme: Teaching Scheme TH TU PR PAPER
More informationOptions to Improve the MEN System into the 21 st Century
Options to Improve the MEN System into the 21 st Century Chris Halliday Electrical Consulting and Training Pty Ltd, Gladstone NSW, Australia. Email: chris@elect.com.au Web: www.elect.com.au Abstract Network
More informationMV ELECTRICAL TRANSMISSION DESIGN AND CONSTRUCTION STANDARD. PART 1: GENERAL 1.01 Transformer
PART 1: GENERAL 1.01 Transformer A. This section includes liquid filled, pad mounted distribution transformers with primary voltage of 12kV or 4.16kV (The University will determine primary voltage), with
More informationARC FLASH PPE GUIDELINES FOR INDUSTRIAL POWER SYSTEMS
The Electrical Power Engineers Qual-Tech Engineers, Inc. 201 Johnson Road Building #1 Suite 203 Houston, PA 15342-1300 Phone 724-873-9275 Fax 724-873-8910 www.qualtecheng.com ARC FLASH PPE GUIDELINES FOR
More informationModel 3725/2M. Line Impedance Stabilization Network (LISN) User Manual
Model 3725/2M Line Impedance Stabilization Network (LISN) User Manual ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any
More informationSlip, Trip & Fall Prevention Program (Sample)
Slip, Trip & Fall Prevention Program (Sample) Introduction United Heartland has developed this Sample Slip, Trip and Fall (STF) Prevention Program as a tool for assisting our customers in the development
More informationThe Upgradabilty of Conventional Three Phase Delta/Star Networks
The Upgradabilty of Conventional Three Phase Delta/Star Networks WHY NEW STANDARDS? CAPITAL COSTS Initial Final OPERATIONAL COSTS UPGRADABILITY SAFETY MAINTAINANCE CONVENTIONAL CONFIGURATION Electrification
More informationPREFACE ********************************************************** IT IS NOT INTENDED THAT THESE STANDARDS BE COPIED AND USED AS A SPECIFICATION!
PREFACE This publication has been prepared as a guide for Architectural and Engineering (A&E) firms in the preparation of documents for the design and construction of new structures and the remodeling
More informationPRA Series of Radio and TV Amplifier Power Supplies
PRA Series of Radio and TV Amplifier Power Supplies The PRA 420 is an antenna power supply, low noise MMIC amplifier and splitter combination to supply up to 24 Shipboard Radios and /or TV Receivers. It
More informationGROUNDED ELECTRICAL POWER DISTRIBUTION. Excerpt from Inverter Charger Series Manual BY: VIJAY SHARMA ENGINEER
GROUNDED ELECTRICAL POWER DISTRIBUTION Excerpt from Inverter Charger Series Manual BY: VIJAY SHARMA ENGINEER .0 Conductors for Electrical Power Distribution For single-phase transmission of AC power or
More informationTEACHER ASSESSMENT BLUEPRINT ELECTRICAL CONSTRUCTION TECHNOLOGY. Test Code: 5171 Version: 01
TEACHER ASSESSMENT BLUEPRINT ELECTRICAL CONSTRUCTION TECHNOLOGY Test Code: 5171 Version: 01 Specific Competencies and Skills Tested in this Assessment: OSHA Regulations and Electrical Safety Practices
More informationPhase 1. GVS Fail safe isolator. ELCB MCB/ Fuse. thermostat at 65⁰C. Slave Control Cables SSR2. for Immersion. Live Only
Wireless connection CYOZ 0.75mm 2 core Screened Control cable Mains cable Phase 1 Renewable Generators Distribution Board Phase 1 AC Isolator GVS Fail safe isolator ELCB MCB/ Fuse Din Rail. ACVT 230 24vAC
More information2015 NFPA 70E. SESHA 2015 ARIZONA MINI CONFERENCE December 10, 2015 Intel Corporation
2015 NFPA 70E SESHA 2015 ARIZONA MINI CONFERENCE December 10, 2015 Intel Corporation Introduction Jeffrey A. Pugh, P.E. Pugh Engineering LLC Bachelor of Science Degrees in Electrical Engineering and Computer
More informationMOBILE SUBSTATIONS 2015 MINNESOTA POWER SYSTEMS CONFERENCE
MOBILE SUBSTATIONS 2015 MINNESOTA POWER SYSTEMS CONFERENCE Scott Storrar Contributors: Bill Hansen, Kyle Reddell, Tom McGrath Basic Mobile Sub Design Equipment mounted on semi-trailer Power transformer
More informationLPB OMNI Broadcast Transmitter Installation Procedure Checklist
Installation Procedure LPB OMNI Broadcast Transmitter Installation Procedure Checklist LPB Communications, Inc. 960 Brook Road, Unit 5 Conshohocken, PA 19428 610-825-4100 phone 610-825-4047 fax www.lpbinc.com!
More informationEmbedded Generation Connection Application Form
Embedded Generation Connection Application Form This Application Form provides information required for an initial assessment of the Embedded Generation project. All applicable sections must be completed
More informationNumbering System for Protective Devices, Control and Indication Devices for Power Systems
Appendix C Numbering System for Protective Devices, Control and Indication Devices for Power Systems C.1 APPLICATION OF PROTECTIVE RELAYS, CONTROL AND ALARM DEVICES FOR POWER SYSTEM CIRCUITS The requirements
More information200B Clipper Module User Manual
Trig-Tek 200B Clipper Module User Manual Publication No. 980954 Rev. A Astronics Test Systems Inc. 4 Goodyear, Irvine, CA 92618 Tel: (800) 722-2528, (949) 859-8999; Fax: (949) 859-7139 atsinfo@astronics.com
More informationSmart Termination TECHNICAL SPECIFICATIONS CURRENT VOLTAGE INSTRUMENTRANSFORMER
Customer : REV. 0 Page 1/16 Smart Termination TECHNICAL SPECIFICATIONS CURRENT VOLTAGE INRUMENTRANSFORMER CVS - 24 - G - Revision Prepared Description Checked by Rev. Date by 0 13/06/16 First issue E.
More informationBritish Columbia Institute of Technology WOOD DUST EXPOSURE CONTROL PLAN (JOINERY)
WOOD DUST EXPOSURE CONTROL PLAN (JOINERY) Contents 1. Purpose... 3 2. Roles & Responsibilities... 3 2.1 School... 3 2.2 Supervisor/Instructor... 3 2.3 Facilities Maintenance... 4 2.4 Housekeeping... 4
More informationA53106 SERIES DC-TO-DC CONVERTER
INSTALLATION & MAINTENANCE A53106 SERIES DC-TO-DC CONVERTER AUGUST 2011, REVISED AUGUST 2014 DOCUMENT NO. COM-00-04-20 VERSION C.1 Siemens Industry, Inc., Rail Automation 9568 Archibald Ave., Suite 100,
More informationArc Flash Analysis and Documentation SOP
Arc Flash Analysis and Documentation SOP I. Purpose.... 2 II. Roles & Responsibilities.... 2 A. Facilities Maintenance (FM).... 2 B. Zone Supervisors/ Shop Foremen... 2 C. PMCS & CPC... 2 III. Procedures...
More informationEASQ ELECTRICAL APPLIANCE SERVICEPERSON (QUALIFIED) MARKING SCHEDULE. SECTION 1 Marks Reference Marking notes Qu 1 A 10 MΩ (2 marks)
EASQ ELECTRICAL APPLIANCE SERVICEPERSON (QUALIFIED) MARKING SCHEDULE Notes: 1. (1mark) means that the preceding statement/answer earns 1 mark. 2. This schedule sets out the expected answers to the examination
More informationFirst Draft Language
110.16 First Draft Language (B) Service Equipment. In addition to the requirements in (A), service equipment shall contain the following information: (1) Nominal system voltage (2) Arc flash boundary (3)
More informationPower Quality Solutions
Power Quality Solutions What is Power Quality? For electrical systems to function in their intended manner without significant loss of performance or life, they require a supply of electricity that is
More information1000 SERIES INSTALLATION SUPPLEMENT Rev. 7/1/10
1000 SERIES INSTALLATION SUPPLEMENT Rev. 7/1/10 Smartscan Incorporated 33083 Eight Mile Road Livonia, MI 48152 Phone: (248) 477-2900 Fax: (248) 477-7453 SMARTSCAN INCORPORATED Livonia, MICHIGAN 1000 The
More informationINDEX. Micro-ohmmeter MH-10 Page 3. MI (5, 10, 15, 20 kv) Page 4 Mega-ohmmeter MD (5 kv) Page 4
Micro-ohmmeter MH-10 Page 3 MI (5, 10, 15, 20 kv) Page 4 Mega-ohmmeter MD (5 kv) Page 4 Earth resistance meter TL-5 Page 5 Indirect earth contact simulator MPC (5, 20, 50 A) Page 6 Trip time tester CR
More informationDISTRIBUTION BUSINESS
DISTRIBUTION BUSINESS DOCUMENT TITLE: MANUAL: DISTRIBUTION NETWORK OPERATION MANUAL DOCUMENT I.D. NUMBER: DS O SW 01 Copyright Aurora REVISIONS REV DATE REVISION DESCRIPTION APPROVAL NO. 1.0 1998 Interim
More informationIDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL:
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-920 The Service Information provides the following information: Precautions and safety information Specifications Performance test procedure Calibration
More information1000 SERIES INSTALLATION SUPPLEMENT Rev
1000 SERIES INSTALLATION SUPPLEMENT Rev. 1-1-12 Smartscan Incorporated 33083 Eight Mile Road Livonia, MI 48152 Phone: (248) 477-2900 Fax: (248) 477-7453 SMARTSCAN INCORPORATED Livonia, MICHIGAN 1000 The
More informationInstructions for Preparing OPTICAL GROUND WIRE IN AN ISOLATOR
Instructions for Preparing OPTICAL GROUND WIRE IN AN ISOLATOR NOTE: EXCEPT AS MAY BE OTHERWISE PROVIDED BY CONTRACT, THESE DRAWINGS AND/OR SPECIFICATIONS ARE THE PROPERTY OF AFL, ARE ISSUED IN STRICT CONFIDENCE
More informationCD770 DIGITAL MULTIMETER INSTRUCTION MANUAL
CD770 DIGITAL MULTIMETER INSTRUCTION MANUAL Table of Contents 1 SAFETY PRECAUTIONS Before use, read the following safety precautions.- 1-1 Explanation of Warning Symbols 001 1-2 Warning Messages for Safe
More informationTW4040. The Adventurer Monobander INSTRUCTION MANUAL. TransWorld Antennas
TW4040 The Adventurer Monobander TransWorld Antennas INSTRUCTION MANUAL Contents 1 Limited Warranty 3 2 Important Safety Information 4 3 Specifications 3.1 Mechanical 4 3.2 Electrical 4 3.3 VSWR Performance
More informationWiMo Antennen und Elektronik GmbH Am Gäxwald 14, D Herxheim Tel. (07276) FAX 6978
2m DISCOVERY LINEAR AMPLIFIER (GS 31) Operating Manual WiMo Antennen und Elektronik GmbH Am Gäxwald 14, D-76863 Herxheim Tel. (07276) 96680 FAX 6978 http://www.wimo.com e-mail: info@wimo.com INDEX 1. Specifications
More information411LA Broadband Power Amplifier
411LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
More informationAppendix S: PROTECTION ALTERNATIVES FOR VARIOUS GENERATOR CONFIGURATIONS
Appendix S: PROTECTION ALTERNATIVES FOR VARIOUS GENERATOR CONFIGURATIONS S1. Standard Interconnection Methods with Typical Circuit Configuration for Single or Multiple Units Note: The protection requirements
More informationOperator's manual TruTool PN 130 (1A1)
Operator's manual TruTool PN 130 (1A1) english TruTool PN 130 (1A1) Table of Contents Table of Contents 1. Safety...4 1.1 1.2 General safety information...4 Specific safety information...5 2. Description...6
More informationKeysight N2771B 30 kv High Voltage Probe
Keysight N2771B 30 kv High Voltage Probe User s Guide Notices Keysight Technologies, Inc. 2012-2015 No part of this manual may be reproduced in any form or by any means (including electronic storage and
More informationTransformer Trainer. Electrical Power Systems PSL20. Learning Outcomes. Key Features. Key Specifications
Electrical Power Systems PSL2 Investigates the principles and operating characteristics of single-phase and three-phase power and distribution transformers Key Features Educational transformers with fully
More informationPRX4SERL Four Zone Receiver Decoder
PRX4SERL Four Zone Receiver Decoder Operating Manual Microframe Corporation 604 S. 12 th Street Broken Arrow, OK 74012 Tel: (918) 258-4839 Toll Free: 1-800-635-3811 Website: www.microframecorp.com E-mail:
More informationSECTION SHORT CIRCUIT, COMPONENT PROTECTION, FLASH HAZARD AND SELECTIVE COORDINATION STUDY
SECTION 16075 - SHORT CIRCUIT, COMPONENT PROTECTION, FLASH HAZARD AND SELECTIVE COORDINATION STUDY PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Provide a short-circuit, component protection, flash
More informationMESP TECHNICAL SPECIFICATION FOR AN ESSENTIAL SERVICES SUPPLY STEP UP TRANSFORMER
Engineering Specification TECHNICAL SPECIFICATION FOR AN ESSENTIAL Version: 3 Issued: 14 October 2016 Owner: Chief Engineer Approved By: Andrew Russack Head of Engineering - Electrical PRINTOUT MAY NOT
More informationV6 series. Instruction Manual. Compact Inverter
Instruction Manual [ IBD#D-I-25-B ] Compact Inverter V6 series Thank you for purchasing our V6 series of inverters. This product is designed to drive a three-phase induction motor. Read through this instruction
More informationWRM-10 TM TRANSFORMER WINDING RESISTANCE METER
WRM-10 TM TRANSFORMER WINDING RESISTANCE METER USER S MANUAL Vanguard Instruments Company, Inc. 1520 S. Hellman Ave. Ontario, California 91761, USA TEL: (909) 923-9390 FAX: (909) 923-9391 June 2009 Revision
More information1600.1D EVO. Owner's Manual. English
1600.1D EVO Owner's Manual English INTRODUCTION Dear customer, Congratulations on acquiring your SounDigital! You've just purchased a product of high quality and technology. The SounDigital products are
More information