Compact Motorized Actuator

Transcription

1 Compact otorized Actuator Using the superior characteristics of the best selling ELY butterfly valve actuator, we developed an improved successor, the. With a replaceable control circuit board, tough metal gears, new limit cam mechanism, a new clutch mechanism, and an improved watertight design, the actuator is even better than before. Features Circuit board is easily replaceable to meet different requirements. New adjustable limit switch cam plate. Waterproof design protects against rain water or condensation Declutchable handwheel for ease of operation and maximum safety. High output torque and compact in size. New ELY Structure figure New ELY Wiring diagrams Standard (With extra position limit switch non-voltage) Type 00 Thermal protector Stop Types to Type 0 to ACTUATOR WIRING LS open LS shut Thermal protector O.L.S S.L.S 0 Stop New ELY-0

2 Type Output torque (Nm) Power source (V) otor capacity (W) Travel time (/Hz) (sec) Electric power consumption (only as a rough standard) Rating (min) Insulation Type of motor and its protective device Space heater Position limit switch Torque limit switch echanical limit stop Conduit connections Enclosure anual operation Number of turns for handle/handwheel Working temperature range Storage temperature range Paint finish Options New ELY Specifications Type 00 Type 0 Type Type Type. Type Type N 0 AC VV0V AC V0VV0V0V /Hz / /0 /0 / /0 0/ (/0) (0/0) (/900) G / (PF /) ports W Option One each at fully opened and closedpositions, contact capacity: ACV-A(Can be used with minimum load down to ma.) Detachable handle. turns ) Space heater W. Servounit, speed controller unit not support 0V, No spaceheater.. With speed controller unit New ELY Tabel actuator selection W W 0 Class E Reversible motor with built-in thermal protector Supplied under the standard specifications One each at fully opened and closed positions, contact capacity: ACV-0A (Can be used with minimum load down to ma.) None End of travel positioning bolt built-in G / (PF /) ports JIS C 090 (IP ), Class, dust and water-jet proof type Declutchable handwheel. turns. turns 0 to degreesc 0 to 0degreesC Epoxy-melanin baked with unsell. BG / ) Potentiometer and 0 ) Intermediate limit switch (no voltage) ) Extra position limit switch contact capacity for minute-load: 0V-mA (Can be used with minimum load down to ma.) ) Servounit (DC 0mA, DCV, 00V) ) Speed controller unit Nominal size mm Z Type 00 Type 0 Type Type Type. Type 00G 0G 0G Type 00 Type 0 Type Type Type. Type Type 00S 0F Type 0 Type Type Type. Type Type T P P X V T Type 00 Type 0 Type Type Type. Type Type 00 Type 0 Type Type Type Type Type Type. Type Type Type 0 Type Type Type. Type Type 0 Type 0 Type Type. Type Type New ELY-0

3 (Approx.) (Approx.) W (Approx.) W W New ELYDimensions Type 00 and 0 P A Types and. A P F K F K G PF H H E G PF H H Type P A Types and P A K F E G PF H H E F K (Approx.) G PF H H otor type Type 00 Type 0 Type Type Type. Type Type ( ): Demension with servounit New ELYDimensions / Weight Dimensionmm H H P A E F K () 0 (9) 9() 0 9() 0 0() 0() W 0 0 Approx. ass kg New ELY-0

4 New ELY ounting details D F F D A B E A B E C G C G New ELY ounting flange details Actuator type A B C D Type 00 Type 0 ISO F0/F0 ISO F0 0 0 /0 0 Type Type ISO F0 ISO F Tomoe Original Tomoe Original Type. ISO F0 ISO F Tomoe Original ISO F ISO F Type ISO F 0. 0 Tomoe Original ISO F Type ISO F Tomoe Original E F Qty / G P./ Dep. / New ELY-0

5 New ELY Terminal board connection diagramtype 00 Notes:. The FG terminal should be grounded.. If a space heater (option) is used, the round terminal should be connected to terminals,, and.. The power sources for the control units are the same for both V and V series, however the actuator motors differ depending on the power source. Terminal block screw size: (with angular washer) Wiring diagram open stop close side d side output power com No No F.G New ELY Terminal board connection diagramtype 0 to () FG contact should be grounded. () If space heater (option) is used, round contact should be connected to contacts and. () Power source for control unit of V series and V series is same, but power source for actuator motor is not. Wirng diagram Input voltage: single phase alternating current /Hz Common Stop Output voltage Output voltage for open side for closed side Terminal block screw size: (with washer) 9 0 CO NC NO CO NC NO side Extra limit switch for open side Extra limit switch for closed side id point side Output for potentiometer (option) F.G. New ELY-0

6 New ELYTerminal board (Type 0 to ) Terminal No. Specification Standard with extra position limit switches With intermediate limit switches With a potentiometer and extra position limit switches With a potentiometer and intermediate limit switches COON switch switch Extra position limit switch,open end intermediate limit switch COON intermediate limit switch NC intermediate limit switch NO Extra position limit switch, close end intermediate limit switch COON intermediate limit switch NC intermediate limit switch NO Potentiometer Potentiometer Potentiometer Earth (F.G.) d d, and 9 are out of use. : wired : not wired New ELY Contacts Terminal No. Connection Capacity CO Common with No. and 9 Contact output OPEN Connect with No. at open position ACV-0A 9 CLOSE Connect with No. at close position. On-off use with extra limit switch (as standard) with intermediate limit switch (as option) Type New ELY Recommended fuse and non-fuse breaker Power source and frequency Recommended capacity for fuse Recommended capacity for non-fuse breaker 0,,.,. odulating use with speed control unit (as option) with servo unit (as option) V/0VHz/Hz V/0VHz/Hz V/0VHz/Hz V/0VHz/Hz V/0VHz/Hz V/0VHz/Hz A A A A A A A A A A A A Type Power source and frequency Recommended capacity for fuse Recommended capacity for non-fuse breaker 0, V/0VHz/Hz V/0VHz/Hz A A A A,. V/0VHz/Hz V/0VHz/Hz A A A A, V/0VHz/Hz V/0VHz/Hz 0A A 0A A New ELY-0

7 New ELY Wiring diagrams (Control options) (Type 0 to ) Standard With extra position limit switch (non-voltage) Purpose To send non-voltage full-open and full-closed signals by switching on and off. ACTUATOR WIRING LS open LS shut Thermal protector O.L.S S.L.S 0 Stop Limit switch contact development Fully closed Fully open O.L.S S.L.S LS open Notes. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switches work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. LS shut With intermediate limit switch Purpose To send intermediate open and close signals by switching on and off, and to stop the valve at intermediate positions. Options Intermediate limit switches (two, non-voltage) ACTUATOR WIRING L S. L S. Thermal protector O.L.S S.L.S 0 Stop Limit switch contact development O.L.S S.L.S LS. Fully closed Intermediate position Intermediate position Fully open Notes. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. LS. New ELY-0

8 New ELY Wiring diagrams (Control options) (Type 0 to ) With potentiometer and extra position limit switch (non-voltage) Purpose To control valve opening by resistance variations and send non-voltage full-open and full-closed signals by switching on and off. Options or 0 potentiometer ACTUATOR WIRING LS open LS shut Potentiometer Thermal protector O.L.S S.L.S 9 0 Stop Limit switch contact development Fully closed Fully open O.L.S S.L.S LS open LS shut Notes. Do not use a switch for two or more of motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switches work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. With thermal output ACTUATOR WIRING LS open LS shut Thermal protector O.LS S.LS Stop 9 0 Limit switch contact development Fully closed O.L.S S.L.S LS open LS shut Fully open Notes. Outputs when thermal operation shall be b contacts.. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switche work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. New ELY-0

9 New ELY Wiring diagrams (Control options) (Type 0 to ) With servo unit, potentiometer and extra position limit switch (non-voltage) Purpose To control valve opening by resistance variations, send intermediate open and close signals, and to stop the valve at intermediate positions by switching on and off. ACTUATOR WIRING Options or 0 potentiometer Intermediate limit switches (two, non-voltage) L S. L S. Potentiometer Thermal protector O.L.S S.L.S 9 0 Stop Notes. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. Input signal Output signal Contact output New ELY Specifications with servo unit (Type 0 to ) DC. to 0 ma (Option to V, 0 to 0 V) DC. to 0 ma Fully open, Fully closed (non voltage) (capacity: AC V-0 A (over 0. A)) Controller Dead band Operation frequency rate Zero span adjustment range Span adjustment Switching of RA and DA Operation temperature % to % variable ED % or less to % FS 0 to 0% FS By changing connector 0 to degrees C New ELY-09

10 Parts list for New ELY (Type 0 to ) With servo unit inside of types 0,, and. Terminal 9 0 Dog for open position Dog for closed position Potentiometer Connector for motor Connector for motor capacitor RA: connector for potentiometer DA: connector for potentiometer 9 RA: wiring connector 0 DA: wiring connector Trimmer for hysterisis adjustment Trimmer for zero adjustment Trimmer for span adjustment Trimmer for output zero adjustment Trimmer for output span adjustment Remarks: When Z is adjusted, then please adjust S too. When Z is adjusted, then please adjust S too. With servo unit inside of types and Terminal Dog for open position Dog for closed position Potentiometer Connector for motor Connector for motor capacitor RA: connector for potentiometer Trimmer for hysterisis adjustment Trimmer for zero adjustment Trimmer for span adjustment Trimmer for output zero adjustment Trimmer for output span adjustment Remarks: When Z is adjusted, then please adjust S too. When Z is adjusted, then please adjust S too. New ELY-0

11 New ELY Wiring diagrams (Control options) (Type 0 to ) With speed controller unit Purpose Set the valve open and close time. Options or 0 potentionmeter, heater O.LS S.LS CONTROL UNIT / Hz Stop O.LS RL Pot Option S.LS 9 0 earth CL Notes. This diagram shows when the valve is at the intermediate position.. Control unit can be used for each voltage by switching jumper pins, but the motor actuator can not. Notes. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switches work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur. Type 0,,. ing degree 0 to 90 degrees C and close time Hz Hz 0sec 0sec sec 00sec 0sec 0sec sec 0900sec Adjustment method Adjustment trimmer New ELY-

12 Parts list for New ELY with speed controller unit (Type 0 to ) Inside of types 0,, and. Terminal Limit switch cam Dog for open position 0 Dog for closed position Dog for open signal Dog for closed signal Connector for potentiometer Connector for motor capacitor Connector for motor Trimmer for closed position Trimmer for open position Inside of types and Terminal Limit switch cam Dog for open position Dog for closed position Dog for open signal Dog for closed signal Connector for potentiometer Connector for motor capacitor Connector for motor Trimmer for closed position Trimmer for open position Connector for open signal Connector for closed signal Connector for open limit switch Connector for closed limit switch New ELY-

13 New ELYAdjustable operating speed (Type 0 to ) Stroke time for open to close and close to open can be set independently. See the trimmer position for operating speed adjustment. Trimmer position and stroke time Position Type 0, and Type. Type Type Hz Hz Hz Hz Hz Hz Hz Hz sec 0 sec sec 0 sec sec sec 0 sec 0 sec Tolerance ± sec Tolerance ± sec 90 sec 0 sec 0 sec 0 sec sec 0 sec 0 sec sec Tolerance ± 0 sec Tolerance ± 0 sec 0 sec sec sec Tolerance ± 0 sec 0 sec 0 sec 0 sec sec Tolerance ± 0 sec 900 sec () Carry out the procedure after the limit switch and stopper bolt are set. () Adjust the trimmer with a screwdriver following the table above. () Standard stroke time can be set by turning the trimmer fully in the clockwise direction. () Stroke time can be adjusted by turning the trimmer counterclockwise. New ELY-

14 New ELY Rated current New ELY- Type otor voltage (V) Impressed voltage (V) Frequency (Hz) Starting current (A) Rated current (A) Note means not available as standard specification. Values are provided as reference.