ST 3000 Smart Pressure Transmitter Series 900 Differential Pressure Models. Specification and Model Selection Guide. Introduction 34-ST /08

Transcription

1 ST 3000 Smart Pressure Transmitter Series 900 Differential Pressure Models STD94 0 to 400 inho 0 to 1,000 mar STD930 0 to 100 psi 0 to 7,000 mar STD974 0 to 3000 psi 0 to 10,000 mar Introduction 34-ST /08 Specification and Model Selection Guide In 1983, Honeywell introduced the first Smart Pressure Transmitter the ST In 1989, Honeywell launched the first all digital, i-directional protocol for smart field devices. Today, its ST 3000 Series 900 Differential Pressure Transmitters continue to ring proven smart technology to a wide spectrum of pressure measurement applications, from furnace comustion airflow rate to hydrostatic tank gauging. The ST 3000 S900 Differential Pressure Transmitter can e used with any primary flow element to provide proven, repeatale flow measurement. All ST 3000 transmitters can provide a 4-0 ma output, Honeywell Digitally Enhanced (DE) output, HART output, or FOUNDATION Fieldus output. When digitally integrated with Honeywell s Process Knowledge System, EXPERION PKS, ST 3000 instruments provide a more accurate process variale as well as advanced diagnostics. Honeywell s cost-effective ST 3000 S900 transmitters lead the industry in reliaility and staility: Staility = ±0.01% per year Reliaility = 470 years MTBF Figure 1 Series 900 Differential Pressure Transmitters feature proven piezoresistive sensor technology. The devices provide comprehensive self-diagnostics to help users maintain high uptime, meet regulatory requirements, and attain high quality standards. S900 transmitters allow smart performance at analog prices. Accurate, reliale and stale, Series 900 transmitters offer greater turndown ratio than conventional transmitters. "Honeywell transmitters operating in the digital mode using Honeywell's Digitally Enhanced (DE) protocol make diagnostics availale right at the control system's human interface. Equally important, transmitter status information is continuously displayed to alert the operator immediately of a fault condition. Because the process variale (PV) status transmission precedes the PV value, we are guaranteed that a ad PV is not used in a control algorithm. In addition, i-directional communication provides for remote transmitter configuration directly from the human interface, enaling management of the complete loop. Maureen Atchison, DuPont Site Electrical & Instrumentation Leader

2 Page Description The ST 3000 transmitter can replace any 4 to 0 ma output transmitter in use today and operates over a standard two-wire system. The measuring means is a piezoresistive sensor, which actually contains three sensors in one. It contains a differential pressure sensor, a temperature sensor, and a static pressure sensor. Microprocessor-ased electronics provide higher span-turndown ratio, improved temperature and pressure compensation, and improved accuracy. The transmitter s meter ody and electronics housing resist shock, viration, corrosion, and moisture. The electronics housing contains a compartment for the single-oard electronics, which is isolated from an integral junction ox. The single-oard electronics is replaceale and interchangeale with any other ST 3000 Series 100 or Series 900 model transmitter. Like other Honeywell transmitters, the ST 3000 features two-way communication and configuration capaility etween the operator and the transmitter through several Honeywell field-rated portale configuration devices, including the Smart Field Communicator (SFC) and the Multiple Communication Configurator (MC ToolKit). While oth are made for infield use, the MC Toolkit also can e ordered for use in intrinsically safe environments. The SCT 3000 Smartline Configuration Toolkit provides an easy way to configure instruments using a personal computer. The toolkit enales configuration of devices efore shipping or installation. The SCT 3000 can operate in the offline mode to configure an unlimited numer of devices. The dataase can then e loaded down-line during commissioning. Features Choice of linear or square root output conformity is a simple configuration selection. Direct digital integration with Experion PKS and other control systems provides local measurement accuracy to the system level without adding typical A/D and D/A converter inaccuracies. Unique piezoresistive sensor automatically compensates input for temperature and static pressure. Added smart features include configuring lower and upper range values, simulating accurate analog output, and selecting preprogrammed engineering units for display. Smart transmitter capailities with local or remote interfacing means significant manpower efficiency improvements in commissioning, start-up, and ongoing maintenance functions.

3 Page 3 Specifications Operating Conditions All Models Parameter Reference Condition (at zero static) Rated Condition Operative Limits Transportation and Storage C F C F C F C F Amient Temperature 5 ±1 77 ± -40 to to to to to to 57 Meter Body Temperature 5 ±1 77 ± -40 to to to to to to 57 Humidity %RH 10 to 55 0 to to to 100 Vacuum Region - Minimum Pressure mmhg asolute inho asolute Atmospheric Atmospheric 5 13 (short term ) 1 (short term ) Supply Voltage, Current, and Load Resistance Maximum Allowale Working Pressure (MAWP) 4 (ST 3000 products are rated to Maximum Allowale Working Pressure. MAWP depends on Approval Agency and transmitter materials of construction.) Voltage Range: 10.8 to 4.4 Vdc at terminals Current Range: 3.0 to 1.8 ma Load Resistance: 0 to 1440 ohms (as shown in Figure ) STD94, STD930, STD974 = 4500psi, 310 ar 3 Static Pressure Limit = Maximum Allowale Working Pressure (MAWP) = Overpressure Limit 1 For CTFE fill fluid, the rating is 15 to 110 C (5 to 30 F) Short term equals hours at 70 C (158 F) 3 MAWP applies for temperature range 40 to 15 C. However Static Pressure Limit is de-rated to 3000 psi from -6 to -40 C. Use of graphite o-rings de-rates transmitter to 365 psi. Use of Adapter with graphite o-rings de-rates transmitter to 3000 psi. 4 Consult factory for MAWP of ST3000 transmitters with CSA approval Loop Resistance (ohms) Note: A minimum of 50 ohms of loop resistance is necessary to support communications. Loop resistance equals arrier resistance plus wire resistance plus receiver resistance. 50 = Operating Area Operating Voltage (Vdc) Figure Supply voltage and loop resistance chart

4 Page 4 Performance Under Rated Conditions* - Model STD94 (0 to 400 inh O/1000 mar) Parameter Description Upper Range Limit inho mar 400 (39. F/4 C is standard reference temperature for inho range.) 1000 Minimum Span inho 10 Note: Recommended minimum span in square root mode is 0 inho (50 mar). mar 5 Turndown Ratio 40 to 1 Zero Elevation and Suppression 5 to +100% URL. Accuracy (Reference Includes comined effects of linearity, hysteresis, and repeataility) Accuracy includes residual error after averaging successive readings. For FOUNDATION Fieldus use Digital Mode specifications. For HART use Analog Mode specifications. Zero Temperature Effect per 8 C (50 F) Comined Zero and Span Temperature Effect per 8 C (50 F) Zero Static Pressure Effect per 1000 psi (70 ar) Comined Zero and Span Static Pressure Effect per 1000 psi (70 ar) Staility In Analog Mode: ±0.075% of calirated span or upper range value (URV), whichever is greater, terminal ased. For URV elow reference point (5 inho), accuracy equals: 5 inh O ± span inh O or ± 6 mar span mar In Digital Mode: ±0.065% of calirated span or upper range value (URV), whichever is greater, terminal ased. For URV elow reference point (5 inho), accuracy equals: 5 inh O ± span inh O or ± In Analog Mode: ±0.165% of span. For URV elow reference point (50 inho), effect equals: 50 inh O ± span inh O In Digital Mode: ±0.15% of span. or ± For URV elow reference point (50 inho), effect equals: ± inh O span inh O 6 mar span mar 15 mar span mar 15 mar or ± 0.15 span mar In Analog Mode: ±0.5% of span. For URV elow reference point (50 inho), effect equals: 50 inh O ± span inh O or ± 15 mar span mar In Digital Mode: ±0.5% of span. For URV elow reference point (50 inho), effect equals: 50 inh O ± span inh O or ± 15 mar span mar ±0.165% of span. For URV elow reference point (50 inho), effect equals: 50 inh O ± span inh O or ± ±0.30% of span. For URV elow reference point (50 inho), effect equals: 50 inh O ± span inh O ±0.015% of URL per year or ± 15 mar span mar 15 mar span mar * Performance specifications are ased on reference conditions of 5 C (77 F), zero (0) static pressure, 10 to 55% RH, and 316L Stainless Steel arrier diaphragm.

5 Performance Under Rated Conditions* - Model STD930 (0 to 100 psi/7000 mar) Parameter Upper Range Limit Minimum Span psi ar psi ar Turndown Ratio 0 to 1 Zero Elevation and Suppression 5 to +100% URL. Accuracy (Reference Includes comined effects of linearity, hysteresis, and repeataility) Zero Temperature Effect per 8 C (50 F) Comined Zero and Span Temperature Effect per 8 C (50 F) Zero Static Pressure Effect per 1000 psi (70 ar) Comined Zero and Span Static Pressure Effect per 1000 psi (70 ar) Staility Description 34-ST Page 5 In Analog Mode: ±0.075% of calirated span or upper range value (URV), whichever is greater, terminal ased. For URV elow reference point (0 psi), accuracy equals: 0 psi 1.4 ar ± or ± span ar In Digital Mode: ±0.065% of calirated span or upper range value (URV), whichever is greater, terminal ased. For URV elow reference point (0 psi), accuracy equals: 0 psi 1.4 ar ± or ± span ar In Analog Mode: ±0.165% of span. For URV elow reference point (30 psi), effect equals: 30 psi ar ± or ± span ar In Digital Mode: ±0.15% of span. For URV elow reference point (30 psi), effect equals: ± 30 psi ar 0.15 or ± span ar 0.15 In Analog Mode: ±0.5% of span. For URV elow reference point (30 psi), effect equals: 30 psi ar ± or ± span ar In Digital Mode: ±0.5% of span. For URV elow reference point (30 psi), effect equals: 30 psi ar ± or ± span ar ±0.165% of span. For URV elow reference point (30 psi), effect equals: 30 psi ar ± or ± span ar ±0.30% of span. For URV elow reference point (30 psi), effect equals: 30 psi ar ± or ± span ar ±0.04% of URL per year * Performance specifications are ased on reference conditions of 5 C (77 F), zero (0) static pressure, 10 to 55% RH, and 316L Stainless Steel arrier diaphragm.

6 Page 6 Performance Under Rated Conditions* - Model STD974 (0 to 3000 psi/10 ar) Parameter Upper Range Limit Minimum Span psi ar psi ar Turndown Ratio 30 to 1 Zero Elevation and Suppression 0.6 and +100% URL. Accuracy (Reference Includes comined effects of linearity, hysteresis, and repeataility) Accuracy includes residual error after averaging successive readings. For FOUNDATION Fieldus use Digital Mode specifications. For HART use Analog Mode specifications. Zero Temperature Effect per 8 C (50 F) Comined Zero and Span Temperature Effect per 8 C (50 F) Zero Static Pressure Effect per 1000 psi (70 ar) Comined Zero and Span Static Pressure Effect per 1000 psi (70 ar) Staility Description In Analog Mode: ±0.% of calirated span or upper range value (URV), whichever is greater, terminal ased. For URV elow reference point (300 psi), accuracy equals: 300 psi 1 ar ± or ± span ar In Digital Mode: ±0.175% of calirated span or upper range value (URV), whichever is greater, terminal ased. For URV elow reference point (300 psi), accuracy equals: 300 psi 1 ar ± or ± span ar In Analog Mode: ±0.15% of span. For URV elow reference point (500 psi), effect equals: 500 psi 35 ar ± or ± span ar In Digital Mode: ±0.0% of span. For URV elow reference point (500 psi), effect equals: ± 500 psi 35 ar 0.0 or ± span ar 0.0 In Analog Mode: ±0.35% of span. For URV elow reference point (500 psi), effect equals: 500 psi 35 ar ± or ± span ar In Digital Mode: ±0.30% of span. For URV elow reference point (500 psi), effect equals: 500 psi 35 ar ± or ± spanpsi span ar ±0.165% of span. For URV elow reference point (500 psi), effect equals: 500 psi 35 ar ± or ± span ar ±0.30% of span. For URV elow reference point (500 psi), effect equals: 500 psi 35 ar ± or ± span ar ±0.03% of URL per year * Performance specifications are ased on reference conditions of 5 C (77 F), zero (0) static pressure, 10 to 55% RH, and 316L Stainless Steel arrier diaphragm.

7 Performance Under Rated Conditions - General for all Models Parameter Output (two-wire) Supply Voltage Effect Damping Time Constant CE Conformity (Europe) NAMUR NE 43 Compliance Option SIL /3 Compliance Lightning Protection Option (Code LP ) Physical and Approval Bodies Parameter Barrier Diaphragms Material STD94, STD930, STD974 Process Head Material STD94, STD930, STD974 Head Gaskets Meter Body Bolting Optional Adapter Flange and Bolts Mounting Bracket Fill Fluid Electronic Housing Description Analog 4 to 0 ma or DE digital communications mode. Options availale for FOUNDATION Fieldus and HART protocol % span per volt. Adjustale from 0 to 3 seconds digital damping. 89/336/EEC, Electromagnetic Compatiility (EMC) Directive. 34-ST Page 7 Transmitter failure information is generated when the measuring information is invalid or no longer present. Failure information is transmitted as a current signal ut outside the normal 4-0 ma measurement signal level. Transmitter failure values are: 3.6 ma and 1.0 ma. The normal signal range is 3.8 ma and 0.5 ma. SIL certified to IEC for non-redundant use in SIL related Safety Systems (single use) and for redundant (multiple) use in SIL 3 Safety Systems through TÜV Nord Sys Tec GmH & Co. KG under the following standards: IEC : 1998; IEC : 000; IEC : Leakage Current: 10 microamps 4.4 VDC, 93 C Impulse Rating: 10/0 µ sec. 5,000 Amps (50 strikes) 10,000 Amps (0 strikes) (rise/decay) 10/1000 µ sec. 50 Amps (1000 strikes) 500 Amps (400 strikes) Description 316L SS, Hastelloy C-76, Monel, Tantalum, Gold plated 316LSS, Gold plated Hastelloy C-76, Gold plated Monel, Caron Steel (zinc-plated), Monel, Hastelloy Glass filled PTFE standard. Viton and graphite optional. Caron Steel (Zinc plated) standard. Options include, NACE A86 SS olts with NACE 304 SS nuts, and B7M. Adapter Flange materials include, Hastelloy C-76 and Monel. Options for olting include caron steel, 316SS, NACE A86SS and B7M. Standard adapter flange gasket material is glass filled PTFE. Viton and graphite optional. Caron Steel (Zinc-plated) or Stainless Steel angle racket or Caron Steel flat racket availale (standard options). Silicone DC 00 oil or CTFE (Chlorotrifluoroethylene) Epoxy-Polyester hyrid paint. Low Copper-Aluminum. Meets NEMA 4X (watertight) and NEMA 7 (explosionproof). Stainless steel optional. Process Connections 1/4-inch NPT; 1/-inch NPT with adapter. Process heads meet DIN 1913 requirements. Wiring Accepts up to 16 AWG (1.5 mm diameter). Mounting Can e mounted in virtually any position using the standard mounting racket. Bracket is designed to mount on -inch (50 mm) vertical or horizontal pipe. See Figure 3. Dimensions See Figure 4. Net Weight Approximately 9 pounds (4.1 Kg)

8 Page 8 Physical and Approval Bodies (continued) Parameter Approval Bodies Factory Mutual CSA Canadian Registration Numer (CRN) ATEX SA (Australian) Description Explosion Proof: Approved as Explosion Proof for Class I, Division 1, Groups A, B, C, D locations, Dust Ignition Proof: Approved as Dust Ignition Proof for Class II,, Division 1, Groups E, F, G locations, Intrincically Safe: Approved as Intrinsically Safe for for Class I, II,, Division 1, Groups A, B, C, D, E, F, G locations. Nonincendive: Approved as Nonincendive for Class I, Division, Groups A, B, C, D locations. Explosion Proof: Approved as Explosion Proof for Class I, Division 1, Groups B, C, D locations, Dust Ignition Proof: Approved as Dust Ignition Proof for Class II,, Division 1, Groups E, F, G locations, Intrincically Safe: Approved as Intrinsically Safe for Class I, II,, Division 1, Groups A, B, C, D, E, F, G locations. All ST 3000 model designs, except SATG19L, STG99L, STG170 and STG180 have een registered in all provinces and territories in Canada and are marked CRN:0F8914.5c. Intrinsically Safe, Zone 0/1: EEx ia IIC T4, T5, T6 Flameproof/Zone 1: EEx d IIC T5, T6 (enclosure IP 66/67) Non-Sparking, Zone : EEx na, IIC T6 (enclosure IP 66/67) Multiple Markings: Ex II 1 G: EEx ia IIC T4, T5, T6, Ex II G: EExd IIC T5, T6 Ex II 3 G: EEx na, IIC T6 (Honeywell) (enclosure IP 66/67) Intrinsically Safe: EX ia IIC T4 Non-Sparking: Ex n IIC T6 (T4 with SM option) INMETRO (Brazil) Flame-Proof, Zone 1: EX d IIC T5 Pressure Equipment Directive (97/3/EC) The ST 3000 pressure transmitters listed in this Specification have no pressurized internal volume or have a pressurized internal volume rated less than 1,000 ar (14,500 psig) and/or have a maximum volume of less than 0.1 liter. Therefore, these transmitters are either; not suject to the essential requirements of the directive 97/3/EC (PED, Annex 1) and shall not have the CE mark, or the manufacturer has the free choice of a module when the CE mark is required for pressures > 00 ar (,900 psig). NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from exceeding allowale pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive 97/3/EC article 1,.1.3), require separate examination. Figure 3 Examples of typical mounting positions

9 Page 9 Reference Dimensions: millimeters inches Figure 4 Typical mounting dimensions for STD94, STD930 and STD974 for reference.

10 Page 10 Mounting Bracket The angle mounting racket is availale in either zinc-plated caron steel or stainless steel and is suitale for horizontal or vertical mounting on a two inch (50 millimeter) pipe, as well as wall mounting. An optional flat mounting racket is also availale in caron steel for two inch (50 millimeter) pipe mounting. Indicating Meter (Options ME and SM) Two integral meter options are availale. An analog meter (option ME) is availale with a 0 to 100% linear scale. The Smart Meter (option SM) provides an LCD display for oth analog and digital output and can e configured to display pressure in pre-selected engineering units. Lightning Protection (Option LP) A terminal lock is availale with circuitry that protects the transmitter from transient surges induced y neary lightning strikes. HART Protocol Compatiility (Options HC and H6) Optional electronics modules for the ST 3000 that provides HART protocol compatiility in either the HART 5.x or 6.x formats. Transmitters with a HART option are compatile with any HART enaled system that provides either 5.x or 6.x format support. FOUNDATION Fieldus (Option FF) Equips transmitter with FF protocol for use in 31.5 kit/s FF networks. See document 34-ST for additional information on ST 3000 Fieldus transmitters. SIL/SIL3 Certification (Option SL) This ST 3000 product is availale for use with safety systems. With the SL option, we are fully certified to SIL capaility for single transmitters and SIL 3 capaility for multiple transmitter use through TÜV Nord Sys Tec GmH & Co. KG. Options We are in compliance with the following SIL standards: IEC : 1998; IEC : 000; IEC : 1998 NAMUR NE43 Compliance (Option NE) This option provides software the meets the NAMUR NE43 requirements for failsafe software. Transmitter failure information is generated when the measuring information is no longer valid. Transmitter failure values are: 3.6 ma and 1.0 ma. The normal ST 3000 ranges are 3.8 ma and 0.5 ma. Indicator Configuration (Option CI) Provides custom configuration of Smart Meters. Tagging (Option TG) Up to 30 characters can e added on the stainless steel nameplate mounted on the transmitter s electronics housing at no extra cost. Note that a separate nameplate on the meter ody contains the serial numer and ody-related data. A stainless steel wired on tag with additional data of up to 4 lines of 8 characters is also availale. The numer of characters for tagging includes spaces. Transmitter Configuration (Option TC) The factory can configure the transmitter linear/square root extraction, damping time, LRV, URV and mode (analog/digital) and enter an ID tag of up to eight characters and scratchpad information as specified. Custom Caliration and ID in Memory (Option CC) The factory can calirate any range within the scope of the transmitter s range and enter an ID tag of up to eight characters in the transmitter s memory. Ordering Information Contact your nearest Honeywell sales office, or In the U.S.: Honeywell Industrial Automation & Control North Black Canyon Hwy. Phoenix, AZ In Canada: The Honeywell Centre 155 Gordon Baker Rd. North York, Ontario MH 3N In Latin America: Honeywell Inc. 480 Sawgrass Corporate Parkway, Suite 00 Sunrise, FL 3335 (954) In Europe and Africa: Honeywell S. A. Avenue du Bourget Brussels, Belgium In Eastern Europe: Honeywell Praha, s.r.o. Budejovicka Prague 4, Czech Repulic In the Middle East: Honeywell Middle East Ltd. Khalifa Street, Sheikh Faisal Building Au Dhai, U. A. E. In Asia: Honeywell Asia Pacific Inc. Honeywell Building, 17 Changi Business Park Central 1 Singapore Repulic of Singapore In the Pacific: Honeywell Pty Ltd. 5 Thomas Holt Drive North Ryde NSW Australia 113 (61 ) In Japan: Honeywell K.K Shiaura 1-chrome Minato-ku, Tokyo, Japan Or, visit Honeywell on the World Wide We at: Specifications are suject to change without notice. (Note that specifications may differ slightly for transmitters manufactured efore Octoer 30, 1995.)

11 Page 11 Model Selection Guide (34-ST-16-4) Model Selection Guide 34-ST-16-4 Issue 43 Instructions Select the desired Key Numer. The arrow to the right marks the selection availale. Make one selection from each tale, I and II, using the column elow the proper arrow. Select as many Tale options as desired (if no options or approvals are desired, specify 9X). A ( ) denotes unrestricted availaility. A letter denotes restricted availaility. Restrictions follow Tale IV. Key Numer I II (Optional) IV - _ - _ -,, + XXXX KEY NUMBER Span 0-10" to 0-400" H O/0-5 to 0-1,000 mar Body Rating: 4,500 psi (310 ar) 0-5 to psi/ to 0-7 ar Body Rating: 4,500 psi (310 ar) to 0-3,000 psi/0-7 to 0-10 ar Body Rating: 4,500 psi (310 ar) Selection STD94 STD930 STD974 Availaility Important Note: Base STD models no longer include a default communications option. All units now require the selection of a communication option from Tale (AN, DE, HC, H6 or FF). TABLE I - METER BODY Process Wetted Heads Materials of Construction Fill Fluid Process Head Configuration TABLE II No Selection Caron Steel * Caron Steel * Caron Steel * Caron Steel * Hastelloy C Hastelloy C Monel Vent/Drain Valves ** and Plugs Hastelloy C Hastelloy C Monel Silicone CTFE 1/4" NPT Barrier Diaphragms 316L SS Hastelloy C Monel Tantalum 316L SS Hastelloy C Monel Tantalum Hastelloy C Tantalum Monel 1/" NPT with Adapter (on 1/4" NPT Head) Selection A B C D E F G H J K L _ 1 _ A H t t t * Caron Steel heads are zinc-plated and not recommended for water service due to hydrogen migration. For that service, use 316 stainless steel wetted Process Heads. ** Vent/Drains are Teflon coated for luricity.

12 Page 1 STD9xx Availaility TABLE - OPTIONS Selection Communication Options (Must choose a communications option) Analog only (can e configured using appropriate Honeywell DE tool) AN DE Protocol communications DE HART 5.x Protocol Compatile Electronics HC HART 6.x Protocol Compatile Electronics H6 FOUNDATION Fieldus Communications FF r r r Indicating Meter Options Analog Meter (0-100 Even 0-10 Square Root) ME Smart Meter SM Custom Configuration of Smart Meter CI e e e Local Zero LZ x x x Local Zero and Span ZS m m m Transmitter Housing & Electronics Options NAMUR Failsafe Software NE SIL - TÜV Certified transmitter (requires HC/H6 and WP options) SL p p p Lightning Protection LP Custom Caliration and I.D. in Memory CC Transmitter Configuration - (non-fieldus) TC Transmitter Configuration - (Fieldus) FC Write Protection (Delivered in the "enaled" position) WP Write Protection (Delivered in the "disaled" position) WX Electronics Housing - with M0 Conduit Connections 1/" NPT to M0 Conduit Adapter (BASEEFA EEx d IIC) 1/" NPT to 3/4" NPT Conduit Adapter Housing with M0 to 1/" NPT Conduit Adapter (use for FM and CSA Approvals) Stainless Steel Customer Wired-On Tag (4 lines, 8 characters per line, customer supplied information) Stainless Steel Customer Wired-On Tag (lank) Low Temperature o C Amient Limit End Cap Live Circuit Warning Lael in Spanish (only with ATEX 3D) End Cap Live Circuit Warning Lael in Portuguese (only with ATEX 3D) End Cap Live Circuit Warning Lael in Italian (only with ATEX 3D) End Cap Live Circuit Warning Lael in German (only with ATEX 3D) Meter Body Options (Seal olt material depends on Transmitter olt material) Bolts and Nuts for Process Heads B7M Bolts and Nuts for Process Heads NACE A86 SS Bolts and NACE 304 SS Nuts for Process Heads Adapter Flange - 1/" NPT with CS Bolts Adapter Flange - 1/" NPT with Bolts Adapter Flange - 1/" NPT with NACE A86 SS Bolts Adapter Flange - 1/" NPT with B7M Bolts Hastelloy C Adapter Flange - 1/" NPT with CS Bolts Hastelloy C Adapter Flange - 1/" NPT with Bolts Monel Adapter Flange - 1/" NPT with CS Bolts Monel Adapter Flange - 1/" NPT with Bolts Blind Adapter Flange with CS Bolts Blind Adapter Flange with Bolts Blind Adapter Flange with NACE A86 SS Bolts Blind Adapter Flange with B7M Bolts Side Vent/Drain (End Vent Drain is standard) Center Vent Drain and Bushing Viton Process Head Gaskets (adapter gaskets ordered separately) Graphite Process Head & Adapter Flange Gaskets Viton Adapter Flange Gaskets SH n n n A1 n n n A i i i A3 TG TB LT SP 18 a a a PG a a a TL a a a GE a a a SS B7 CR S c c c S3 c c c S4 c c c S5 c c c T c c c T3 c c c V c c c V3 c c c B3 B4 B5 B6 SV CV VT GF VF i i i Tale continued next page

13 Page 13 STD9xx Availaility TABLE - OPTIONS (continued) Selection Transmitter Mounting Brackets Options Mounting Bracket - Caron Steel MB Marine Approved Mounting Bracket - Caron Steel MX Mounting Bracket SS SB Marine Approved Mounting Bracket SS SX Flat Mounting Bracket - Caron Steel FB Services/Certificates/Marine Type Approvals Options User's Manual Paper Copy (Standard, HC, H6 or FF ships accordingly) UM Clean Transmitter for Oxygen or Chlorine Service with Certificate 0X j j j Over-Pressure Leak Test with F339 Certificate TP Caliration Test Report and Certificate of Conformance (F3399) F1 Certificate of Conformance (F3391) F3 Diaphragm Options Gold plated diaphragm(s) on G1 Gold plated diaphragm(s) on Monel or Hastelloy ONLY G Certificate Options Certificate of Origin (F0195) F5 FMEDA Certificate (SIL 1) (FC3331) F6 SIL Certificate (SIL /3) (FC33337) FE NACE Certificate (Process-Wetted & Non-Process Wetted) (FC33339) F7 o o o NACE Certificate (Process-Wetted) (FC33338) FG Marine Type Approvals (DNV, ABS, BV, KR & LR) (FC33340) MT Warranty Options Additional Warranty - 1 year Additional Warranty - years Additional Warranty - 3 years Additional Warranty - 4 years W1 W W3 W4 Approval Approval Type Body No hazardous location approvals Explosion Proof Dust Ignition Proof Factory Non-Incendive Mutual Intrinsically Safe Explosion Proof Dust Ignition Proof CSA Intrinsically Safe SA (Australia) TABLE IV Factory Identification Intrinsically Safe Non-Sparking Intrinsically Safe, Zone 0/1 Location or Classification Class I, Div. 1, Groups A,B,C,D Class II, Div. 1, Groups E,F,G Class I, Div., Groups A,B,C,D Class I, II,, Div. 1, Groups A,B,C,D,E,F,G Class I, Div. 1, Groups B,C,D Class II,, Div. 1, Groups E,F,G Class I, II,, Div. 1, Groups A,B,C,D,E,F,G Ex ia IIC T4 Ex n IIC T6 (T4 with SM option) EEx ia IIC T4, T5,T6 Selection 9X J 4G 3S f EEx d IIC T5, T6, Flameproof, Zone 1 3D Enclosure IP 66/67 Non-Sparking, EEx na, IIC T6 ATEX* 3N Zone (Honeywell). Enclosure IP 66/67 Multiple Marking** Ex II 1 G EEx ia IIC T4, T5, T6 Int. Safe, Zone 0/1, or Ex II G EEx d IIC T5, T6 3H Flameproof, Zone 1, or Ex II 3 G EEx na, IIC T6 (Honeywell) Non-Sparking, Zone Enclosure IP 66/67 INMETRO Flameproof, Zone 1 Ex d IIC T5 6D (Brazil) *See ATEX installation requirements in the ST 3000 User's Manual ** The user must determine the type of protection required for installation of the equipment. The user shall then check the ox [ ] adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection has een checked on the nameplate, susequently the equipment shall not e reinstalled using any of the other certification types. 1C XXXX

14 Page 14 RESTRICTIONS Restriction Availale Only With Not Availale With Letter Tale Selection Tale Selection a 3D or 3H Select only one option from this group c I H e SM f I L i j I 1C or J m ME, FF n 1C, J o CR, S4, B5 p r HC or H6 and WP FF, 00 TC, ME, 4G t Select from Tale S, S3, S4, S5, T, T3, V, V3 x FF, SM 15 MX, SX FB, MB, SB FF 17 VT 18 I _ 1 _ 19 F7, FG 1 FF SL Note: See ST-83 for Pulished Specials with pricing. See ST-89 and User's Manual for part numers. See ST-OE-9 for OMS Order Entry Information including TC, manuals, certificates, drawings and SPINS. See ST-OD-1 for tagging, ID, Transmitter Configuration (TC) and caliration including factory default values. To request a quotation for a non-pulished "special", fax RFQ to Marketing Applications ST 3000 is a registered trademark of Honeywell International Inc. HART is a registered trademark of the Hart Communication Foundation. FOUNDATION is a trademark of the Fieldus Foundation. Honeywell Process Solutions Industrial Measurement and Control Honeywell International Inc. 500 W. Union Hill Drive Phoenix, Arizona 8507 Honeywell International Inc.