VJ-1204 OPERATION MANUAL ERRATA

Size: px

Start display at page:

Download "VJ-1204 OPERATION MANUAL ERRATA"

Basil Barnett
5 years ago
Views:

1 VJ-1204 OPERATION MANUAL ERRATA Some contents of the Operation Manual are changed. Make sure the following list shown below. TIP The content of this documents are being based on the firmware version later than (1) Operation Manual Chapter Item Description Chapter 3 Chapter 4 Chapter 5 in 3.3 Installing ink cartridges in Setup print in 3.6 Adjust print in Set values that can be changed or confirmed while printing in Print Mode menu in Pre Heater menu in Platen Heater menu in StandbyHeating menu Step 1 False: "[KCMY] Discharged" is displayed on the operation panel and the printer starts initial operation. True: The printer starts initial operation. Refer to sheet 3 Refer to sheet 4 Setting value of Pre Heater False: Off / 30to 60 True: Off / 30to 50 Setting value of Platen Heater False: Off / 30to 55 True: Off / 30to 50 Path value of Banner2 (Refer to Details of the print mode ) False: 8 times True: 6 times Setting value False: Off / <30> to 60 True: Off / <30> to 50 Setting value False: Off / <30> to 55 True: Off / <30> to 50 Setting value False: Off / <On> True: 10min to <60min> to 240min VJ1204E-A-00e 1 MUTOH INDUSTRIES LTD.

2 ERRATA VJ-1204 OPERATION MANUAL Chapter Item Description Chapter 5 in Effect menu Add FrontTreatment menu in 5.5 Selection menu Refer to sheet 5 Refer to sheet 6 Refer to sheet 7 Add 5.6 Version Menu Refer to sheet 8 Chapter 7 in Error message display and remedies No.6 False: [******] Cartridge True: [******] No Cartridge (2) Quick Referense Page Item Description p.3-10 p.3-27 in 3.4 Installing ink cartridges in Set values that can be changed or confirmed while printing Step 1 False: "[KCMY] Discharged" is displayed on the operation panel and the printer starts initial operation. True: The printer starts initial operation. Setting value of Pre Heater False: Off / 30to 60 True: Off / 30to 50 Setting value of Platen Heater False: Off / 30to 55 True: Off / 30to 50 VJ1204E-A-00e 2 MUTOH INDUSTRIES LTD.

3 VJ-1204 OPERATION MANUAL ERRATA VJ1204E-A-00e 3 MUTOH INDUSTRIES LTD Setup print

4 ERRATA VJ-1204 OPERATION MANUAL 3.6 Adjust print Modified the step 8. c. Check three print samples that printed with Bi-D Quality pattern, and select the number that is not out of alignment. 4 is selected in the next printing sample. Alignment Bi-D Q VJ1204E-A-00e 4 MUTOH INDUSTRIES LTD.

5 VJ-1204 OPERATION MANUAL ERRATA Effect menu Set up the Effect menu. Set up this menu when improving the printing quality to adjust the quality to the printing mode. NOTE The printing quality may not be improved according to the printing condition. Effect Setup item Setting value Description None 1 None 2 The Effect function is not used. If obvious white lines or uneven print density appear on printed media in None 1, set to None 2. Wave 1 Wave 2 Wave 3 Wave 4 The printing joint will be the wave form. It will be improved the printing quality. If obvious white lines or uneven print density appear on printed media in Wave 1, change the setting to the one with the best print result in Wave 2 to 4. <Fine&Wave 1> Fine&Wave 2 Fine&Wave 3 Fine&Wave 4 Perform printing at a slow speed compared with "Wave". Set up this menu when improving the printing quality compared with "Wave". If obvious white lines or uneven print density appear on printed media in Fine&Wave 1, change the setting to the one with the best print result in Fine&Wave 2 to 4. A-S. Fine&Wave Performs Wave printing is using one side of the nozzles of the print head. Since only one side of the nozzles is used, printing speed becomes half of Wave 1 to 4. Set up this menu when improving the printing quality compared with Fine&Wave 1 to 4. B-S. Fine&Wave Performs Wave printing using the other side of the nozzles of the print head that is used for A-S.Fine&Wave. Since only one side of the nozzles is used, printing speed becomes half of Wave 1 to 4. Set up this menu when improving the printing quality compared with Fine&Wave 1 to 4. [Enter] key: Save the setting value and shift to the previous hierarchy. [Cancel] key: Cancel the setting value and shift to the previous hierarchy. 5.1 Setup menu VJ1204E-A-00e 5 MUTOH INDUSTRIES LTD.

6 ERRATA VJ-1204 OPERATION MANUAL Front Interlace menu Set the front treatment function. This function is applied when the banding appears at the beginning of print. Setup item Setting value Description FrontInterlace Off The front treatment function is not used. <On> The front treatment function is used. [Enter] key: Save the setting value and shift to the previous hierarchy. [Cancel] key: Cancel the setting value and shift to the previous hierarchy. 5.1 Setup menu VJ1204E-A-00e 6 MUTOH INDUSTRIES LTD.

7 VJ-1204 OPERATION MANUAL ERRATA 5.5 Selection menu Set up the contents of the Setup menu. This enables to hide the infrequently-accessed Setup menu on the display. Press either [<] or [>] key on the Operation panel to switch On (display) /Off (nondisplay). When the setup is made (On), the mark is displayed on the Operation panel. <The following information include no change> VJ1204E-A-00e 7 MUTOH INDUSTRIES LTD.

8 ERRATA VJ-1204 OPERATION MANUAL 5.6 Version menu Display the version of firmware. It displays the firmware version of main side (M) and controller side (C). Ver.M/C Setup item Setting value Description *.**(Main)/*.**(Controller) Display the version of firmware. - [Cancel] key: Shift to the previous hierarchy. 5.1 Setup menu VJ1204E-A-00e 8 MUTOH INDUSTRIES LTD.

This document bridges the gap between the Fiery XF documentation and the Mutoh VJ-1617H documentation.

Mutoh VJ-117H This document bridges the gap between the Fiery XF documentation and the Mutoh VJ-117H documentation. Refer to the Installation section before you connect the printer to a computer. The Operation