2.4G. wireless transmission technology. Technical Application Guide for UP-SHINE LED Ceiling light UP-AL W-AW

Transcription

1 2.4G wireless transmission technology Technical Application Guide for UP-SHINE LED Ceiling light UP-AL W-AW

2 Introduction 2.4G wireless transmission technology AL2 Oyster LED ceiling light can be controlled by 2.4G wireless remote controller, offering dimmable, color changeable (controlled by remote controller /switch), power off memory and timing switch functions etc. The light color can be adjusted from warm white to cold white, from dark to bright. The ceiling light will keep the memory in the last lighting mode (light color and brightness) when in OFF situation over 1 seconds. Timing switch function brings personalized energysaving experience. Low power consumption, fast switch between different functions, excellent stability and strong anti-interference capacity make this lamp outstanding. Up to 7% energy saving compared to standard CFL Long lifetime of 4, hours Dimmable when using 2.4G remote controller Color changeable. (Controlled by remote controller or by switch) Power off memory: The lamp will be the same brightness and color when it's on after power off or it's turned off more than 1 seconds. 12 wide beam angle CCT: 27K~57K No UV/IR light Environment friendly, without Mercury or any other hazardous substances Application notes IP2 for indoor use Professional electrician for installation only Switch off before installation Do not touch when in use Keep away from hot steam and corrosive gas Application Areas Suitable for commercial and residential applications like office, supermarket, shop, school, hotel, restaurant, workshop, warehouse, home etc. Certificate

3 Product Information Ø35 11 Technical Specifications Model Voltage Power Power Factor Lumen (±5%) Beam angle CCT Lifespan CRI Dimmable Dimension UP-AL W-AW AC1-24V 25W.9 ~ o 27~57K 4h 8 Yes Ø35*11mm Driver data Sheet Driver data DIM Input rated Voltage Frequency Input Voltage AC1-24V 5/6Hz AC85-265V Efficiency 85% Total load Wattage 25W±5% Power Factor.9 Rated input current Full load output Voltage Rated output current.3a DC24-38V 6mA Power tolerance ±5% Current output tolerance ±5% Dimming range 5%-1% Dimmer Short circuit protection Over voltage protection Over temperature protection Withstand voltage 2.4G.RF PASS PASS PASS AC15V Fixture Compatibility Rated Wattage Electrical Classification Ingress Protection Operating Temp Operating Humidity Storage Temp 25W Ⅰ IP2-2 o C~45 o C ~9% -2 o C~65 o C

4 Spectral Distribution 27K 4K Max=1413 [1.=2] 3.5SDCM F27K.8 Max=8231 [1.=2] SDCM F4K Spectrum x=.4464 y=.449 Spectrum x=.3841 y= Wavelength(nm) Wavelength(nm) 5K 57K.8 Max=8735 [1.=2] 2.23SDCM F5K.8 Max=787 [1.=2] 4.91SDCM F57K Spectrum x=.3496 y=.366 Spectrum x=.3473 y= Wavelength(nm) Wavelength(nm) Photometric Diagram 27K 4K Polar intensity diagram Cartesian intensity diagram Beam diagram Polar intensity diagram Cartesian intensity diagram Beam diagram / E(LX) Planar Illuminance Curve MH=1m C/18 C9/27 Flux out: 1182 lm 3.281ft 9.885, 44.53fc 1m 16.4, 479.3lx 6.562ft 2.471, 11.13fc 2m 26.6, 119.8lx 12.2ft cm 24.3ft cm / E(LX) Planar Illuminance Curve MH=1m C/18 C9/27 Flux out: 1255 lm 3.281ft 1.49, 47.28fc 1m 112.9, 59.lx 6.562ft 2.622, 11.82fc 2m 28.23, 127.2lx 11.87ft cm 23.74ft cm ft 3m 1.98, 4.948fc 11.82, 53.26lx 36.5ft cm ft 3m 1.165, 5.254fc 12.55, 56.55lx 35.61ft cm ft.6178, 2.783fc 4m 6.65, 29.96lx 48.7ft cm ft.6556, 2.955fc 4m 7.57, 31.81lx 47.48ft cm AVERAGE BEAM ANGLE(5%): DEG Distance(m) 16.4ft.3954, 1.781fc 6.9ft 5m 4.256, 19.17lx cm Height Eavg, Emax Angle: deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance AVERAGE BEAM ANGLE(5%): DEG Distance(m) 16.4ft.4196, 1.891fc 59.35ft 5m 4.516, 2.36lx cm Height Eavg, Emax Angle: deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. 5K 57K Polar intensity diagram Cartesian intensity diagram Beam diagram Polar intensity diagram Cartesian intensity diagram Beam diagram / E(LX) Planar Illuminance Curve MH=1m C/18 C9/27 Flux out: 1242 lm 3.281ft 1.38, 46.89fc 1m 111.7, 54.7lx 6.562ft 2.595, 11.72fc 2m 27.93, 126.2lx 11.84ft 36.93cm 23.68ft cm / E(LX) Planar Illuminance Curve MH=1m C/18 C9/27 Flux out: 1337 lm 3.281ft 11.18, 5.5fc 1m 12.3, 543.5lx 6.562ft 2.794, 12.62fc 2m 3.7, 135.9lx 11.89ft cm 23.79ft cm ft 3m 1.153, 5.21fc 12.42, 56.8lx 35.52ft cm ft 3m 1.242, 5.611fc 13.37, 6.39lx 35.68ft cm ft.6488, 2.93fc 4m 6.983, 31.54lx 47.37ft cm ft.6984, 3.156fc 4m 7.518, 33.97lx 47.57ft cm AVERAGE BEAM ANGLE(5%): DEG Distance(m) 16.4ft.4152, 1.875fc 59.21ft 5m 4.469, 2.19lx cm Height Eavg, Emax Angle: 122.2deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance AVERAGE BEAM ANGLE(5%): DEG Distance(m) 16.4ft.447, 2.2fc 59.46ft 5m 4.812, 21.74lx cm Height Eavg, Emax Angle: deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.

5 Polar Diagram Comparison -15 O 18 O 15 O -12 O 12 O -9 O 9 O O 33 6 O 44-3 O 55 3 O O AVERAGE BEAM ANGLE (5%): 122.2DEG C/18, deg C3/21, 122. deg C6/24, deg C9/27, deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11%.4 Lifetime (hours) o C 75 o C 85 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 85% % 75% FLUX.1.5 U'V' 7% LifeTime (hours) Temperature The testing is operated at 25 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C The highest withstand temperature of IC, MOS could be 12 C The highest withstand temperature of LED junction temperature is 15 C 1 Temperature ( o C) :13:13 11:31:1 11:49:1 12:7:1 12:25:1 12:43:1 13:1:1 13:19:1 13:37:1 Time 13:55:1 14:13:1 14:31:1 14:49:1 15:7:1 15:43:1 16:1:1 16:19:1 16:37:1 IC Capacitor MOS PCB LED Fitting Environmental temperature The driver lifespan is based on capacitor working temperature.

6 2.4G wireless transmission technology Adopting 2.4 G high frequency wireless remote control, this light enjoys the characters of low power consumption, far transmission distance, strong anti-interference capacity, high communication rate. It can be used as night light, the lamp enjoy the memory function. (when the light was turned off, it will memorize the brightness before you turn off) ON OFF Night lamp 5% Brightness Dimming Change color Group dividing Code Matching and grouping: (only they are code matched with each other can the lamp be controlled remotely) Select the lamp need to be conducted with grouping control; after turning off the power for 1 seconds, turn on the power again; in this moment (within 3 seconds), press the Group On button ( ); the lamp will flash for 3 times to confirm the matching and grouping is done. Repeat the steps above until all the lamps are matched and grouped. Only after this step, the function as below can be set up (color control, light control, timing and night lamp). Clear code and Re-grouping: (disconnect the led lamp and remote controller to cancel the remote control) Cut off the power supply for 1 seconds and switch on again, at the moment it s switched on, press group on button ( ) 5 times in a row, then the lamp with quick flashing 6 times which predict the success of code cleaning. Repeat the step of group code matching can work for LED lights again. Synchronous and Re-grouping control: (for light dimming and colour changeable) Synchronous Press Full ON button ( ) enter into Synchronous set mode, press each function button to control all groups of LED lamp processing light dimming, colour changeable, timing and night lamp function at the same time. Re-grouping Press group on button ( ) enter into re-grouping set mode, press each function button to control LED lamp in one single group processing light dimming, colour changeable, timing and night lamp function at the same time. Turn-off timing function: With keeping normal power on position, long-press full ON button ( ). After the lamp's quick flashing, press the timing length button within 3 seconds, then the lamp will flash 1-4 times in line with duration which predict the timing success. To cancel the timing function, press full OFF button ( ) Arst, then turn them back on.

7 5% brightness function: Press "5% brightness" button ( ), all LED lamps controlled by this controller will turn into 5% brightness mode. Press any button on this remote controller can exit from this mode. Night lamp function: (for all groups) Press "Night light" button ( ), all LED lamps controlled by this controller enter into night light mode, the light brightness can reach at 2 of the maximum brightness. Press any button on this remote controller can exit from this mode. Night lamp function: (For separate group) With keeping normal power on, long-press full "OFF" button ( ) in separate group at least 2 seconds, the corresponding LED lamp enters into night light mode, the light brightness can reach at 2 of the maximum brightness. Press any button on this remote controller can exit from this mode. Grouping control: (remote controller makes several-for -one or one-for-several control possible with LED lamp) Keep the original mode, Cut off the power supply for 1 seconds and switch on again, use another remote controller operating grouping code within 3 seconds. Then the LED lamp sets can be controlled by other remote controller. Cut off the power supply for 1 seconds and switch on again, use same remote controller operating grouping code within 3 seconds. Then different group of LED lamp sets can be controlled by same remote controller. Memory Function: The lamp will be the same brightness and color when it's on after power off or it's turned off. You can set 4 different lighting situations (warm white, cold white, daylight white and sleep/ night light) by switching your light switch on and off (the light must remain switched off for at least one second). The lamp has a memory function so that the lighting / dimming situation that you last set will automatically occur when you next activate the lamp. (However, the light must remain switched off for at least 1 seconds)

8 A B C D Installation (US) Unbox ceiling light and accessory pack. Rotate to separate lamp shade and 1 base plate. 2 Fix screw on junction box. 3 Naught wire Black Live wire White Ground wire Green Switch off, wiring live, Neutral and Ground by terminal cap respectively. 4 Surface mount the base plate to ceiling by fasten screw. 5 OFF ON Rotate to unite the lamp shade and the base plate. 6 Finish 7

9 A B C D Installation (EU) Unbox ceiling light and accessory pack. Knock-in the plastic anchor into ceiling. Rotate to separate lamp shade and base plate Surface mount the base plate to ceiling. Switch off, wiring live, Neutral and Ground by terminal cap respectively. 4 L=BROWN N=BLUE =YELLOW GREEN 5 Rotate to unite the lamp shade and the base plate. Finish. OFF 6 ON 7 Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 75*4* CTNS Q'TY(PCS) VOLUME(CBM) 2'' standard container 4'' standard container Phone: Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China