Making a Small Four Claw Collet.
|
|
- Ashley Singleton
- 5 years ago
- Views:
Transcription
1 Making a Small Four Claw Collet. Making a four claw collet is a very handy skill to have. These collets are quite readily available from the supply houses and the smaller sizes are very cheap. But knowing how to make then is not really about saving money, but rather it's about getting the job done. This tutorial shows how to make the entire collet, all the while still attached to the parent metal rod. With a bit of practice, making one when you use this method takes about fifteen minutes. Instead of having to wait for the jewellery supplier to deliver, or having to drive to them to collect it, fifteen minutes later you are completing the job. Much more efficient.
2 I have a ring that needs to be set with two 2.5 mm round gemstones. So I start with a piece of rod 3.5 mm in diameter. Image No.1 I first drill a 1.5 mm hole about 4 mm deep in the center. Image No.2 Page No. 1
3 Then first with a scriber and then with your piercing saw, I make a cut about 4.5 mm from the end. Not to deep, just the depth of the blade. I use this groove as a guide for my barrette file in the next step. Image No.3 I take my barrette needle file and file a cone shape as shown in the picture. The nice thing with this method of making a collet is that the collet is worked until the final finish and only then is it cut off. So it is very easy to manipulate while you are working it. Image No.4 Page No. 2
4 Once the cone is neat and round, I cut down about two thirds, thus making the start of four claws. Image No.5 Then I take a 2 mm ball frazer and expand the inner diameter of the collet. Image No.6 Page No. 3
5 I use a 1mm barrel burr to expand the saw cuts down. The burr also leaves the bottom of the claws rounded. Image No.7 A pre cut is made as to where the collet will be trimmed off. A sanding disk is also now used to finish the claws on the inside. Also before cutting the collet off, it is completely polished. This is easy when the collet is still attached to the rod. The depth of the claws 2/3 to 1/3, is also shown in the picture. Image No.8 Page No. 4
6 I have not polished this example, because the polished surface give off to many reflections. However, normally it would be polished before it is soldered into the setting. Image No.9 The collet is held in place with binding wire. Image No.10 Page No. 5
7 Normally, if it is possible, the collet is soldered in from behind. Image No.11 Here is the collet set with a 2.5 mm gemstone. Image No.12 Page No. 6
8 Additional Notes. Here is a picture of the hanging motor sanding mandrels I speak of in my tutorials. I have three of each, ( tapered, barrel, straight ) in each of the grit of sand papers listed below. Image No.13 This is a handy way of storing your sand paper strips. I simply make then by cutting them with an old pair of scissors. And to speed things up, I cut three sheets at once. Then I clip them in a bulldog clip and hang then on the side of my bench. I use 220, 1200,and 5000 grit grit is great when you can get it. For what it's worth, I got mine at Polierblock.de The other grits I buy at a normal hardware store. Image No.14 Page No. 7
9 Files are generally sold without handles, as shown in the picture above. The tapered part on the right hand side is called the tang. Swiss files are graded on the tang according to their roughness. OOO--very coarse, OO- less coarse,o-medium coarse, 1-- medium 2-- fine 3-finest, or also known as dead smooth. Always buy the best quality files you can afford, because they last longer and work quicker. At the bottom of the page to my Half Round Filing tutorial are two GIF images showing the correct filing motion when filing a ring. In the picture above are shown medium length files,about 150 mm ( 6 inches) tooth area, which is the most common size used for jewellery making. I like the new type handles that have a screw nut in them, so that all that is required is to put the tang in and screw them tight. Image No.15 The top three files are needle files. Needle files come in all shapes and lengths and generally don't require handles, although they are available, and if your hands are small, can be required for better file control. The fourth and fifth files from the top are escapement files, also known as watch makers files. They are used for fine work. The bottom file is a specialist file called a round edge pillar file. It has teeth only on the edges and is one of those tools you use only once a year. Image No.16 I show it only for demonstrative purposes. Page No. 8
10 Here are some samples of the burrs most often mentioned in my tutorials. The barrel burrs come in many sizes. As a professional, I use barrel burrs, ball frazers and setting burrs from 11 mm to 0.5 mm in size. But for practical and purposes, 5 mm to 0.5 mm are all that is really needed. I use the large sizes very seldom. Drills come in sizes from 2.3 mm down to 0.5mm. Tapered frazers are less important but I show them for demonstration purposes. Image No.17 Just to show what a piercing saw looks like. The most common size of blade I use is 3/0. The blades are graded from 8/0 which are the finest to 1/0, the coarsest. There are many other different types of blades, including ones designed to cut wax, wood, plastics and diamond impregnated ones to cut stone. Blades generally are sold in bundles of twelve or in packets of twelve bundles. (144) Practically spoken, a packet of 3/0 and 8/0 will last you a very long time. Image No.18 Page No. 9
11 Often, when people start out with jewellery making, they want to own every single tool in existence. ( I include myself) However, as your skill level increases, it becomes apparent that more tools are not really needed, and in fact, less is more. The pliers shown below are enough to start someone off and excluding a few specialty pliers not shown, are more than adequate to make a wide range of jewellery. I have drawn the nose profiles in above and in front of the individual pliers. Tube bender for bending round circles from 2 mm to 5 mm. Double round for bending jump rings. Flat for bending things 90º Half round flat for bending rings round. Chain nose for bending jump rings. Fine flat same as flat, but smaller. Image No.19 Parallel Jaw, very handy pliers and also made in different sizes and shapes. Ring benders are used to close rings up. Side cutters for cutting thin wire. Solder snips for cutting your solder into tiny pieces. Image No.20 Page No. 10
12 I am always striving to make my tutorials better and better and a large part of that improvement comes from you, the person who uses them. Any suggestions, comments and ideas that could improve the tutorials are greatly appreciated. I answer every question that is asked and I am more than willing to give advice if you find yourself with a problem in the tutorial. Another thing that gives me great pleasure is when my students send me pictures of the finished jewellery. So don't be shy, send them to me at hansmeevis@gmail.com Sincerely yours, Hans Meevis Page No. 11
tools cutters 524 orderline: larsson side cutters, larsson end cutters tools
cutters larsson side cutters, larsson end cutters Side Cutters: 999 720 Diagonal cutters, pointed jaws (3054) flush cut for wire Ø 0.35-1.00mm 29.75 999 721 Diagonal cutters pointed jaws (3055) regular
More informationASSIGNMENT 4. Textbook Assignment: The point, edge, face, heel, and tang are the five parts of which of the following tools?
ASSIGNMENT 4 Textbook Assignment: "Files," "Grinders and Sharpening Stones," "Scrapers," "Awls," "Bolt and Cable Cutters," "Glass Cutters," "Knives,' 'Pipe Cutting and Threading Tools," "Tube Cutting and
More informationMarlene s Favorite Tools
Marlene s Favorite Tools Shears or tin snips Item #111236 Light-duty shears are great for intricate work. Use the curved-blade shears to cut smooth, even curves. Straightblade shears for straight cuts
More informationFlat file. Round file. Hand file. Half -round. Mill file. Square file
Name Picture Cross section Uses: Cut pattern:: Hand file used for roughing and finishing. It has double cut teeth on two faces, single cut teeth on one edge, and one safe edge Flat file used for roughing
More informationLegacy DaVinci Pen Kit
Description: The DaVinci model is a single tube pen kit that uses a 3/8 tube and is a great starter kit for those new to pen turning. They are look similar to our Viceroy kit with a more intricate design.
More informationWitch Hat Pendant By Valorie Clifton
Witch Hat Pendant By Valorie Clifton Ah, Halloween! It s always been one of my favorite holidays. The kids and I like to watch Halloween movies. We decorate the house and enjoy the cooler temperatures
More informationThe saw is not a decoration piece but sees regular use at the school. The cross pieces at either end are made from oak, the long stretchers are made
Roy s Saw When you walk in the front door of Roy Underhill s Woodright s School and look to your left in the window hanging above Roy s stuffed chicken is a large frame saw. Now the chicken is an interesting
More informationSTEEL RULE. Stock TRY SQUARE
FITTING INTRODUCTION Fitting consists of a handwork involved in fitting together components usually performed at a bench equipped with a vice and hand tools. The matting components have a close relation
More informationLegacy Classic Twist Pencil Kit
Legacy Pencil Kit Description: The pencil is great kit and has features to make it a step-up pen. It is slightly more difficult to make, but still very easy if you follow these instructions carefully.
More informationLegacy Slimline Pencil Kit
Description: The model is considered one of the most basic pen kits and is a great starter kit for those new to pen turning. Many experienced pen turners use the kit to make elaborate and unusual pens
More informationFlexible Diamond Disc
Diamond Burs - with 2.37mm HP Shanks The abrasive properties of Diamond bonded to the tool ensure fast, easy action & long durability. Used for engraving, drilling, cutting, cleaning castings, etc. Always
More informationTortoise Switch Machines, Mounted Horizontally
Tortoise Switch Machines, Mounted Horizontally by David King Have you ever used the Tortoise Switch Machines manufactured by Circuitron. These are a wonderful stall motor slow motion switch machine that
More informationLearn how to make decorative rivets while working with this uncommon alloy. by Addie Kidd
PROJECT INTERMEDIATE METAL Shibuichi Cuff: Learn how to make decorative rivets while working with this uncommon alloy. by Addie Kidd To take full advantage of shibuichi, you ve got to use patinas. One
More informationLegacy Upgraded Junior Gentlemen s Pen Kit
Description: The Upgraded Junior Gentlemen s model is a classic style pen which is easy to turn and uses a Roller Ball Refill which is highly desirable among pen enthusiasts The Upgraded Junior Gentlemen
More informationLegacy Hex Pencil Kit
Description: The Hex pencil is a step-up kit, with similar features to a Slimline Pro Pencil. It has a click mechanism instead of a twist. It uses an 3/8 tube and 2MM pencil lead. It has a heavier feel
More informationElectrical Construction Name:
Tools of the Trade The following are common tools that are used in the electrical industry. This hand-out is to help familiarize you with the tools, the terminology, and their use. Retractable Steel tape
More informationQuestion 1. Flat file. Half -round. Round file. Three square ( triangle ) Needle files. Page 1 of 46
Question 1 Name Picture Cross section Uses: Cut pattern:: Flat file Half -round Round file Three square ( triangle ) Needle files Page 1 of 46 Question 2 The graph shown below is the data collected for
More informationTurning between centers - another way
Turning between centers - another way There has been a fair amount of discussion of turning between centers and questions always pop up and it seems like we've never really sat down and discussed the process
More informationPliers Assortments. 207 Pliers Assortment 207 Pliers Assortment, 3-pieces 207 Pliers Assortment, 4-pieces
Content Pliers. Page Article group Page Article group Heavy Duty Combination Pliers. 197 Heavy Duty Combination Pliers 198 Long Round Nose Plier 198 Long Flat Nose Plier 198 Chain Nose Pliers, straight
More informationto Precious From Plumbing PROJECT INTERMEDIATE METALS facetjewelry.com FCT-MW
PROJECT INTERMEDIATE METALS From Plumbing to Precious FCT-MW-061217-07 2013 Kalmbach Publishing Co. This material may not be reproduced in any form without permission from the publisher. facetjewelry.com
More informationLegacy Polaris Pen Kit
Description: The Polaris model is a single tube pen kit that uses a 3/8 tube and is a great starter kit for those new to pen turning. They look similar to our Viceroy kit but the body tube is longer which
More informationInvisible Clip Tutorial
Invisible Clip Tutorial I first saw what I call the Invisible Clip in Russ Fairfield s PMG gallery and fell in love with it. I could not figure out how he made them so I sent him an e-mail and he was kind
More informationSheet Metal Tools. by:prem Mahendranathan
Sheet Metal Tools by: SHEET METAL TOOL KIT SHEET METAL TOOLS Rivet Gun 3/32, 1/8, 5/32, 3/16",Cupped Set Mini Bucking Bar Footed Heel-Toe Bucking Bar Air Tool Oil Mechanics Tool Bag High-Speed Air Drill
More informationLegacy Slimline Touch Pen Kit
Description: The model is considered one of the most basic pen kits and is a great starter kit for those new to pen turning. Many experienced pen turners use the kit to make elaborate and unusual pens
More informationLegacy Bullet Click Pen Kit
Description: The Bullet Click pen is a step-up kit, with similar features to a Power Click Pen. It has a click mechanism instead of a twist. It uses an 8mm tube and a Parker style gel refill. It is popular
More informationSimple Metalworking Techniques and Making a Steel Butterfly bymattthegamer463 Favorite
Simple Metalworking Techniques and Making a Steel Butterfly bymattthegamer463 Favorite Step 1: Materials and Tools Not too many materials that we need for this job. Materials: - 22 gauge steel sheet -
More informationMaking A Limited Range Jacobs Flex Collet, version 2
Making A Limited Range Jacobs Flex Collet, version 2 By R. G. Sparber Copyleft protects this document.1 Recently I had the great fortune of receiving a Tapmatic 50X tapping head. It can drive taps as small
More informationSubtractive Wax Working
Society of North American Goldsmiths Artists Designers Jewelers Metalsmiths January 2010 15 TECHNICAL ARTICLE Please note the following correction to the Technical Article TIG Welding for Metalsmiths,
More informationSAW-PIERCING. 79. Fig. 29. Placing new blade in saw-frame.
SAW-PIERCING. 79 First make a full-size drawing of the hinge, then by means of transfer paper transfer the design of the butt end to the copper or brass. Then lay out the knuckles as shown in Fig. 28,
More informationLegacy Magnet Pen Kit
Description: The Magnet pen model is a variation of the Slimline pen and considered one of the most basic pen kits and is a great starter kit for those new to pen turning. Sometimes called the Refrigerator
More informationSellotape Dispenser E112134#1
2. 4 Sellotape Dispenser Please Note The OPITEC range of projects is not primarily intended as toys for young children. It is for teaching, designing and making to ensure that pupils experience a range
More informationMixed Metal Heart Author: Patti Bullard Ph.D.
Mixed Metal Heart Author: Patti Bullard Ph.D. Mixed Metal Heart Difficulty: Easy The beauty of mixed metals paired with a traditional heart shape is sure to bring joy to the jewelry maker as well as the
More informationMECHANICS TOOLS. Back
MECHANICS TOOLS Back FULLER AND FULLER PRO SLIP JOINTS Designed by professionals for professionals, FULLER PRO Slip Joint and Groove Joint Pliers offer a lifetime of performance we guarantee it. The FULLER
More informationColori. Part I Geometry
Colori Part I Geometry 1 2 Determine the size of your cane. TOOLS & MATERIALS FOR BUILDING A CANE: - photocopy paper - ruler - pen or a black marker - color markers (optional) - pasta machine - clay of
More informationSkybolt V2 Construction Manual
Skybolt V2 Construction Manual Property of www.ppgplans.com Do not duplicate or make public. Warnings & Disclaimers. This product shows how to build a basic frame only for Powered Paragliding. It is the
More informationPOWER CARVERS/ACCESSORIES
16 POWER CARVERS/ACCESSORIES Foredom Tools and Accessories Foredom No. 8 handpiece - slim handpiece. Chuck guard sleeve protects fingers and permits close work. Slides back when changing accessories. Includes
More informationThermo fan. Important Notice:
105.434 Thermo fan Important Notice: Beware of fire, never leave a burning candle unattended!! Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching
More informationTools for Plumbing. Introduction
2 Tools for Plumbing Introduction So far, we have studied the importance of plumbing system, its stages and the role and responsibilities of a plumber. We will now look at the various tools that help a
More informationSafety First! Use eye protection, always! Use ear protection with loud power tools. Stay with children while they work!
TM TM ART TABLE Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with children while they work! Follow tool manufacturers safety guidelines Page 1 ART TABLE Page
More informationACCREDITATION FACILITY AUDIT CHECKLIST
ACCREDITATION FACILITY AUDIT CHECKLIST Institution Name: Date: Designated Trade: Machinist AC #: Contact: Location: Course Duration: of weeks: of hours total: of hours per day: Instructor(s) of Students
More informationPliers VDE. Verbindungen mit System The Power of Partnership
Pliers VDE Verbindungen mit System The Power of Partnership Pliers VDE VDE Cable cutter for NYM and NYY cable fully insulated suitable for Cu and aluminium cable opening up to 16 mm 160 KL010160IS 225
More informationObtained from Omarshauntedtrail.com
DaveintheGrave's Halloween Props Animated Crawling Skeleton Build a life-size skeleton torso that realistically crawls across the lawn one arm at a time. 1. Motor Base and Linkage Assembly BASE - I used
More informationASSIGNMENT 3. Textbook Assignment: 3-5. Which of the following types of hammers is used for driving and pulling nails?
ASSIGNMENT 3 Textbook Assignment: "Clamps," "Jacks," Hammers, Mallets, and Mauls," "Screwdrivers," "Manual Drills," "Screw and Tap Extractors," "Wrenches," "Chisels," and "Punches," chapters 19 through
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationHow to make tailwheel shock rubber donuts and aluminum shims with formed flange
How to make tailwheel shock rubber donuts and aluminum shims with formed flange The following shows how to form a flange on the inner hole of aluminum shims to go between the rubber donuts for the tailwheel
More informationModule One: Non Powered Hand Tools
Module One: Non Powered Hand Tools What is included in this module Why are we learning this? Safety rules Right tool for the right job Identity of Tools Hands on time Quiz Why are we here? Basic knowledge
More informationCONTENTS. 4 Introduction 5 Materials 6 Workspace Safety 7 Fabrication Tools & Techniques 31 Torchwork Tools & Techniques
CONTENTS 4 Introduction 5 Materials 6 Workspace Safety 7 Fabrication Tools & Techniques 31 Torchwork Tools & Techniques Projects 42 Sweet & Easy Pearl Drop Earrings 45 Silver Bar & Ruby Earrings 48 Kimono
More informationTHE FULL LINE METAL SPECIALISTS
PRECISION METALS THE FULL LINE METAL SPECIALISTS 6917 West 59th Street Chicago, Illinois 60638 Phone 773/586-8503 Fax 773/586-8556 www.ksmetals.com THE USES ARE ENDLESS!!! Hobby, Craft, DIY, Artist, Architecture,
More informationMINI-LATHE QUICK CHANGE TOOL POST
MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here
More informationMake your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
More informationSOUTH BEND 10 HEAVY LATHE CROSS FEED SCREW REBUILD
The oldest piece of machinery that I have is a South Bend 10 inch heavy lathe. It has become somewhat of a project piece at times having come without a thread dial indicator and a rear cover for the cross
More informationIndian Blanket Blanks
Indian Blanket Blanks Contributed by: Jeff Powell A.K.A workingforwood This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2014 Indian Blanket Blanks
More informationSTRENGTH Aligned teeth provide superior gripping power over standard vertical teeth. STRENGTH Diamond serrated jaws provide a firm grip
STRENGTH Aligned teeth provide superior gripping power over standard vertical teeth STRENGTH Diamond serrated jaws provide a firm grip PLIERS AND SNIPS Locking Pliers Slip Joint Pliers Electrician s Pliers
More informationFigure 9-1 Adjustable wrenches come in a variety of sizes
Figure 9-1 Adjustable wrenches come in a variety of sizes Figure 9-2 Combination wrenches - one end is open and the other end is boxed. Figure 9-3 Refrigerant service valve wrenches have square openings
More informationTravis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise)
Travis Bishop Submitted to: Dr. John Davis Date: 3 December 2012 Course: ETME 310 Section: 004 Lab Topic: Milling Project (Vise) Introduction: Purpose of Experiment: This experiment was conducted to teach
More informationThe Baginski Beveler by Tim Anderson This article appeared in Power Fibers (Volume 36, July 2009)
The Baginski Beveler by Tim Anderson This article appeared in Power Fibers (Volume 36, July 2009) The Baginski Beveler is a roughing beveler that is inexpensive, easy to build, produces accurate strips
More informationHow to Rehandle and Repair that Old Hammer - a Step by Step Tutorial by Bob Sturgeon
How to Rehandle and Repair that Old Hammer - a Step by Step Tutorial by Bob Sturgeon There is a world of old collectible and user hammers out there floating around just waiting to be resurrected. Hammers
More informationFixPad - Create and Assembly instructions
6 7 8 2 9 10 4 3 5 11 1 B.o.m- Bill Of Materials Part No. Part name Production technology File name Martial Info Number of parts Supplier 1 persex sheet Laser cutting, bending Flat pattern base Flat pattern
More informationDIY Kalimba Thumb Piano
DIY Kalimba Thumb Piano By Caleb Schepart of nykalimba.com This DIY Kalimba Thumb Piano build is made using materials, tools, and supplies that are commonly found at a home improvement center, or at a
More informationHow I Made My Aluminum Slim Line Pen
- 1 - How I Made My Aluminum Slim Line Pen Written by Joe Agrella http://www.joespens.com - 2 - Getting Started First and formost remember safety. Remember that you will need eye protection and plenty
More informationA Beginners Guide to Jewellery Making Tools.
A Beginners Guide to Jewellery Making Tools. The Tools of The Trade... Contents page 04 Workbench and Work Area Essentials page 06 Metal Forming When you first begin to make jewellery, the purchase of
More informationHand Tools and Power Tools
Lesson Outcomes The student will be able to: Identify a variety of hand tools and power tools and describe their purpose, application and how they are operated in a safe and proper manner. A wide variety
More informationMaking an Omega Nut. By R. G. Sparber. Copyleft protects this document. 1
Making an Omega Nut By R. G. Sparber Copyleft protects this document. 1 An "Omega nut" is a variation on the idea of a T-nut. While a T-nut slides into a T- slot on a mill table, an Omega-nut slides into
More informationCurved Metal Segmenting
Curved Metal Segmenting A Tutorial by: David Washburn A.K.A djwood1 This tutorial was downloaded from The International Association of Penturners Introduction As I continue to learn about pen turning,
More informationJ D SQUARED INC. NOTCH MASTER Tube and Pipe Notcher Operating Instructions
Copyright (c) 2006 J D SQUARED INC. www.jd2.com NOTCH MASTER Tube and Pipe Notcher Operating Instructions Angled Notches PATENT PENDING Straight Notches Offset Notches Tube Clamp Slider Tube Clamp Exploded
More informationMIX ARGENTIUM &METAL CLAY
PROJECT INTERMEDIATE/ADVANCED METAL CLAY/METAL MIX ARGENTIUM &METAL CLAY in a Floral Pendant FCT-CR-032017_07 Combine two modern forms of silver in a project that plays to the strengths of each material.
More informationStandard Kit #1 (3-way switch)
Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationSingle Barrel Finial Twist Parker Pen. Jeff Powell
Single Barrel Finial Twist Parker Pen by Jeff Powell A.K.A workinforwood This tutorial was downloaded from http://www.penturners.org The International Association of Penturners Single Barrel Finial Twist
More informationA Countersink Gage, version 1.0
A Countersink Gage, version 1.0 By R. G. Sparber Protected by Creative Commons. 1 Marv Klotz recently presented a very nice design for a countersink gage on the Home Made Tools site: http://www.homemadetools.net/forum/countersink-gage-56314
More informationCold-connect Silver &
PROJECT COVER STORY INTERMEDIATE METAL/PLASTIC Cold-connect Silver & ACR YLI C in a Layered Ring Learn to work with modern, lightweight acrylic sheet to introduce transparent color to your work. by Maria
More informationName Hour Course Jewelry/A. Brass Tile Sampler. (use the metal cutter press or hand shears / tin snips)
Jewelry/A Intro: Brass Tile Sampler How do jewelers refine their skills in order to make complex and unique work? The work you do throughout these assignments and units will be the stepping stones for
More informationPlastic Trainer-19. I have tried to only use materials available from the big box building centers like Home Depot, Rona (Canada) and Lowe s.
Plastic Trainer-19 I have tried to only use materials available from the big box building centers like Home Depot, Rona (Canada) and Lowe s. The picture above shows the prototypes with an original Cox
More informationRosalina Accessories Tutorial Version March 2011 Martyn
Rosalina Accessories Tutorial Version 1.0 - March 2011 Martyn Star Brooch Feel free to experiment with these dimensions, you should make a template you are happy with, the method still works. 1) Creating
More informationJimmy s 2 nd demonstration was what he called an African Drum style box made from Iroko with a cocobolo insert in the lid with inlaid sterling silver.
Jimmy s 2 nd demonstration was what he called an African Drum style box made from Iroko with a cocobolo insert in the lid with inlaid sterling silver. He started by roughing out the block with a roughing
More informationThis book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc.
Copyright 2006 - Stay Tooned, Inc. All rights reserved worldwide. This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay
More informationBUILDING A GHOST GLOCK. Prepper Mike
BUILDING A GHOST GLOCK Prepper Mike WHAT IS A GHOST GLOCK? Ghost guns are guns that don t need to be registered Ghost guns are built by the owner based on not more than 80% complete lowers Ghost guns are
More informationTurning Between Centers (Reissued 2015)
Turning Between Centers (Reissued 2015) Contributed by: George Butcher A.K.A Texatdurango This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2015
More informationStrongman Metal Tools Price list February 2018
Strongman Metal Tools CC CK 2004/095733/23 CALL ANDRIES FOR EXPERT ADVICE 083 327 9988 or 087 135 2229 Soli Deo Gloria info@strongman.co.za Strongman Metal Tools Price list February 2018 PLEASE NOTE PRICES
More informationWOOD TOY NEWS. July 23, 2013 Tuesday
WOOD TOY NEWS Make your own perfect turntable for spray painting toys with these useful tips. And it s fast, fun and easy to build! by Imants Udris Watch the video on our website at : http://www.toymakingplans.com/website/how-to/
More informationQRPGuys Iambic Mini Paddle
QRPGuys Iambic Mini Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationHomebrewing. Produced by Al Mecozzi WA8LBZ For the April 5, 2011 Meeting Of the CRES Amateur Radio Club
Homebrewing Produced by Al Mecozzi WA8LBZ For the April 5, 2011 Meeting Of the CRES Amateur Radio Club Additional comments provided by Dave Brown K8AX The goals of tonight's program are to: Get you Interested
More informationTools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More informationChapter # 002 : Creating Threaded Metal Anchoring Points in Fiberglass Foam Structures
Chapter # 002 : Creating Threaded Metal Anchoring Points in Fiberglass Foam Structures The following is a method of creating permanent, threaded, metal anchor point in a foam & fiberglass structure. The
More informationPneumatic Robot arm/digger
1 0 6. 1 8 6 Pneumatic Robot arm/digger Please Note The OPITEC range of projects is not primarily intended as toys for young children. It is for teaching, designing and making to ensure that pupils experience
More informationChain Maille Flower Bracelet Tutorial
Chain Maille Flower Bracelet Tutorial Created by XQ Designs www.handmade-jewelry-club.com, www.diylessons.org Please do not distribute, lend or copy. Do not mass produce. Copyrights 2010 XQ Designs This
More informationSingle MJ Splitter Installation Manual - 1Si
SP1 Single MJ Splitter Installation Manual - 1Si Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2004 Micro
More informationPiston tanks. The spindle nut is machined from mild steel.
Piston tanks Many modelmakers have built four or five subs, own a lathe but only use it to make bollards, antennas and associated fittings. Why not use it to make a piston tank, as opposed to expensive
More informationTable of Contents. Production Options 3. Suggested Tooling 4. Special Considerations 4. Sawing 4. Holding 5. Turning 5. Milling 6.
Table of Contents Production Options 3 Suggested Tooling 4 Special Considerations 4 Sawing 4 Holding 5 Turning 5 Milling 6 Drilling 6 Threading 7 Grinding 7 Buffing and Polishing 8 Deburring 8 Lapping
More informationCentral New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
More informationChapter 26 CHISELS HOW TO CHOOSE AND USE THEM TM 9-243
Chapter 26 CHISELS HOW TO CHOOSE AND USE THEM The Types and Uses section provides you with a list of some of the types of chisels. These pages should help you select the right chisel to do the job. The
More informationRound2it! Mini Electric Sailplane. Round2it
Round2it! Mini Electric Sailplane Round2it Wingspan: 36.0 in. Length: 22.4 in. Wing Area: 164 sq. in. Weight (Ready to Fly): 4.0 to 4.8 oz. Wing Loading: 3.5 4.2 oz. / sq. ft. Version 1.0, September 10,
More information30DC Speed Lathe Manual
30DC Speed Lathe Manual The Crozier Model 30DC Speed Lathe is our most popular model. It has many standard features not found on any other machine in its class or price range. Standard Features 3/4 HP
More informationThere s a trick to using only two prongs. Think Again! Think Two Prongs Can t Secure a Stone? Use sturdy, strategically placed prongs
PROJECT INTERMEDIATE/ADVANCED METAL Think Two Prongs Can t Secure a Stone? Think Again! Use sturdy, strategically placed prongs to set a custom-cut stone. by Jessica Dow and Mark Anderson There s a trick
More informationWrapped Rose. Materials are: 18" piece of 1/4" mild steel rod 1.25" disk of 3/32" thick steel plate. Tools for this project include:
Wrapped Rose In a wrapped rose, the petals and stem are all made from a single round rod. The calyx and leaves are formed separately. Gordon Williams showed me how to make a wrapped rose, and introduced
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationHow to Wire Wrap a Cabochon
How to Wire Wrap a Cabochon Introduction and Materials Cabochons come in many shapes and are made from a variety of stones such as hematite, aventurine, and agate. Though there are many ways to wrap cabs
More informationBand Less Slim Line Pens A How To Guide. Written By: Joe Agrella.
Band Less Slim Line Pens A How To Guide Written By: Joe Agrella http://www.joespens.com/ Step 1: First let s select a nice pen blank. I will use a iron wood blank. Any blank about 5 ½ should do fine. Step
More informationeclecticangler Written By: Michael Hackney
eclecticangler Version 5 Fly Reel Kit Assembly Guide This guide will take you through the assembly process for our new version 5 reel kit and also highlight options to customize the appearance of your
More informationTOOLS AND INSTALLATION
TOOLS AND INSTALLATION Safe, leak-free operation of any high-pressure system is dependent on correctly prepared and installed connections. This section outlines proper instructions for the machining and
More information