Computer Aided Manufacturing
|
|
- Irene Reynolds
- 5 years ago
- Views:
Transcription
1 Computer Aided Manufacturing CNC Milling used as representative example of CAM practice. CAM applies to lathes, lasers, waterjet, wire edm, stamping, braking, drilling, etc. CAM derives process information from the CAD model (although this is sometimes interpreted and re-entered).
2 CNC Milling Advantages of CNC high accuracy with limited verification time higher metal removal rates consistency and accuracy across feeds/speeds operators able to manage several machines inspections can be reduced complex contouring and surfacing is possible
3 Disadvantages of CNC not as flexible as hand work compensation systems need intelligence high initial cost higher maintenance costs part programs are required
4 Classification of CNC Machines Machine Type: PTP vs Contouring Controller: Hardware NC vs CNC/DNC Control System: Closed loop vs Open loop Point to Point machine does not cut while positioning drives are in motion (e.g. drilling machine) Contouring cutting while drives are moving (e.g. milling)
5 Open loop vs Closed Loop Control Open Loop - consider stepper motor drives signal from interpolator (# of pulses & pulse freq.) stepper motor gearing (normally required) drive leadscrew, through to table or spindle axis no feedback limited ability to deal with variable forces, therefore usually used only in PTP machines. BLU defined by one pulse as translated through geartrain.
6 Closed Loop Control signal from interpolator comparator evaluates error DAC converts to analog signal servo drive motor gearing system leadscrew or other drive encoder or linear scale or other feedback sent to comparator. Compensation possible in software.
7 Requirements for CNC Machining geometric information (usually direct from CAD). Sometimes requires adjustment to get best toolpaths. Machining parameters (handbook data) Process planning information (what to do first) Any machine dependant information although this is often added after a generic CNC plan is produced (I.e. CL file or intermediate format) Post processing for specific machine tool appropriate tooling and fixturing
8 Directions for future more powerful processors, more memory more intelligent software and CAD models Adaptive Control adjusting parameters on the fly constraints: cutting force, machining power, cutting torque parameters: feedrate, spindle speed optimizing parameters based on solid modeling info monitoring for tool wear and/or breakage vision systems
9 What is G-Code? G-Code programming is a very robust and simple language. G-codes are what CNC Machines run on. A CNC control program processes the g-code line by line and sends this information to the machine. Precise machine movements result. Where does G-Code come from? From a CAM program and various machining parameters and inputs. It is post-processed for a particular machine
10 Post Processors A post processor is a specific to the machine and normally provided by the machine company or the CAM vendor. There are standard and custom ones. If a standard one doesn t work, most CAM software gives the option to customize the post processor Canned Cycles There are G-Codes that do pertain to Canned Cycles. These are subroutines to complete more complex operations (e.g. peck drilling).
11 G-Code List G0 or G00 Rapid Movement The most rapid movement the CNC Machine can make to the next position. If moving in multiple axes, each axis will move as fast as they can independently of one another. G1 or G01 Linear Movement A straight move with a speed defined by an F. [F=Feedrate] If moving in multiple axes, the machine will move in a straight line such that each axis reaches its defined end point at the same time.
12 G-Code List G2 or G02 Interpolation Clockwise A circular movement in 2-axes in a clockwise motion. Will create an arc to a specified radius defined by an R or I/J combination. G2 or G03 - Interpolation Counter-Clockwise A circular movement in 2-axes in a counterclockwise motion. Will create an arc to a specified radius defined by an R or I/J combination. G4 or G04 Dwell Machine will dwell once reached position to a user defined time, noted by a P
13 G-Code List G20 - Machine in inch mode G21 - Machine in mm mode G28 - Return to Reference Position Normally machine home. G40 - Cutter Compensation Cancel G41 - Cutter Compensation Left G42 - Cutter Compensation Right G43 - Tool Length Compensation + G44 - Tool Length Compensation -
14 G-Code List G54-G59 - Work Coordinate Systems User defined, XYZ G80 - Cancel Canned Cycle G81 - Drilling Cycle G82 - Drilling Cycle G83 - Pecking Cycle G84 - Tapping Cycle G90 - Absolute Co-ordinate entry G91 - Incremental Co-ordinate entry
15 2 Square G-Code Example The numbers on the left of the G-Code are the sequence numbers of the code and the order it will be executed in. Notes are note usually included. Notes start with a - then continues. (i.e. a - means nothing in G-Code).
16 N0000 (Filename: 2INSquare.txt) Name of File N0010 (Post processor: Plasma.post) Name of Post Processor Used N0020 (Date: 8/1/2007) - Date G-Code was generated N0030 G20 (Units: Inches) Measurement Units Used N0040 G53 - Machine co-ordinate system N0050 G90 Absolute Programming N0060 G40 Tool radius compensation off N0070 F1 Feedrate of 1 per min N0090 (Part: Square) name of the part N0100 (Process: Plasma, DEFAULT, Plasma, 0.01 in kerf) Tool to be used N0110 G00 Put in rapid mode N0115 G28 Go to Home position N0120 X Y Move to this exact X, Y position
17 N0130 G04 P2000 Pause for 2 seconds, this is in milliseconds N0140 M03 Fire the plasma torch N0150 G04 P500 - Pause for.5 seconds, this is in milliseconds N0160 G03 X Y I J F40.0 move to this X, Y position in an arcing movement at a feedrate of 40 inches per min N0180 G01 Y Travel in the Y+ direction for 2 inches to X0, Y2 N0200 G01 X Travel in the X+ direction for 2 inches to X2, Y2 N0220 G01 Y Travel in the Y- direction for 2 inches to X2, Y0 N0240 G01 X Travel in the X- direction for 2 inches to X0, Y0 N0250 G03 X Y I J move to this X, Y position in an arcing movement N0260 M05 Turn off the plasma torch N0270 G04 P2000 Pause for 2 seconds, this is in milliseconds N0280 G00 G28 Switch to rapid. Move to Home N0300 M30 End Program
18 What are M-Codes? M-Codes are other codes that are throughout a CNC Program. Think of them like modifiers to the G-Codes. M-Codes are usually very specific to the machine. For example, M03 might stand for Torch On on a CNC Plasma Cutter. It also might stand for Spindle On - Clockwise on a CNC Mill or CNC Router.
19 M-Codes (examples) M0 - program stop M1 - optional program stop M2 - program end M3 - turn spindle clockwise M4 - turn spindle counterclockwise M5 - stop spindle turning M6 - tool change M7 - mist coolant on M8 - flood coolant on M9 - mist and flood coolant off M30 - program end, pallet shuttle, and reset M48 - enable speed and feed overrides M49 - disable speed and feed overrides
NUMERICAL CONTROL.
NUMERICAL CONTROL http://www.toolingu.com/definition-300200-12690-tool-offset.html NC &CNC Numeric Control (NC) and Computer Numeric Control (CNC) are means by which machine centers are used to produce
More informationComputer Numeric Control
Computer Numeric Control TA202A 2017-18(2 nd ) Semester Prof. J. Ramkumar Department of Mechanical Engineering IIT Kanpur Computer Numeric Control A system in which actions are controlled by the direct
More information527F CNC Control. User Manual Calmotion LLC, All rights reserved
527F CNC Control User Manual 2006-2016 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 Phone: (818) 357-5826 www.calmotion.com NC Word Summary NC Word Summary A
More informationBasic NC and CNC. Dr. J. Ramkumar Professor, Department of Mechanical Engineering Micro machining Lab, I.I.T. Kanpur
Basic NC and CNC Dr. J. Ramkumar Professor, Department of Mechanical Engineering Micro machining Lab, I.I.T. Kanpur Micro machining Lab, I.I.T. Kanpur Outline 1. Introduction to CNC machine 2. Component
More informationMach4 CNC Controller Lathe Programming Guide Version 1.0
Mach4 CNC Controller Lathe Programming Guide Version 1.0 1 Copyright 2014 Newfangled Solutions, Artsoft USA, All Rights Reserved The following are registered trademarks of Microsoft Corporation: Microsoft,
More informationCAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing. Part-10 CNC Milling Programming
CAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing Part-10 CNC Milling Programming To maximize the power of modern CNC milling machines, a programmer has to master
More information5/11/ DAWOOD COLLEGE OF ENGINEERING & TECHNOLOGY- ENGR. ASSAD ANIS
1 INTRODUCTION TO CNC CNC was developed in late 40 s and early 1950 s by the MIT servomechanisms laboratory With CNC curves are easy to cut as straight lines, complex 3-D structures are relatively easy
More informationCNC PROGRAMMING WORKBOOK. Sample not for. Distribution MILL & LATHE. By Matthew Manton and Duane Weidinger
CNC PROGRAMMING WORKBOOK MILL & LATHE By Matthew Manton and Duane Weidinger CNC Programming Workbook Mill & Lathe Published by: CamInstructor Incorporated 330 Chandos Crt. Kitchener, Ontario N2A 3C2 www.caminstructor.com
More informationUNIT 5 CNC MACHINING. known as numerical control or NC.
UNIT 5 www.studentsfocus.com CNC MACHINING 1. Define NC? Controlling a machine tool by means of a prepared program is known as numerical control or NC. 2. what are the classifications of NC machines? 1.point
More informationNumerical Control (NC) and The A(4) Level of Automation
Numerical Control (NC) and The A(4) Level of Automation Chapter 40 40.1 Introduction Numeric Control (NC) and Computer Numeric Control (CNC) are means by which machine centers are used to produce repeatable
More informationPROGRAMMING January 2005
PROGRAMMING January 2005 CANNED CYCLES FOR DRILLING TAPPING AND BORING A canned cycle is used to simplify programming of a part. Canned cycles are defined for the most common Z-axis repetitive operation
More informationPerformance. CNC Turning & Milling Machine. Conversational CAM 3.11 Instruction Manual
Performance CNC Turning & Milling Machine Conversational CAM 3.11 Instruction Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 Performance Axis CNC Machine 2 Content Warranty and
More informationCNC Machinery. Module 4: CNC Programming "Turning" IAT Curriculum Unit PREPARED BY. August 2009
CNC Machinery Module 4: CNC Programming "Turning" PREPARED BY IAT Curriculum Unit August 2009 Institute of Applied Technology, 2009 2 Module 4: CNC Programming "Turning" Module 4: CNC Programming "Turning"
More informationMACH3 TURN ARC MOTION 6/27/2009 REV:0
MACH3 TURN - ARC MOTION PREFACE This is a tutorial about using the G2 and G3 g-codes relative to Mach3 Turn. There is no simple answer to a lot of the arc questions posted on the site relative to the lathe.
More informationHAAS AUTOMATION, INC.
PROGRAMMING WORKBOOK HAAS AUTOMATION, INC. 2800 Sturgis Rd. Oxnard, CA 93030 January 2005 JANUARY 2005 PROGRAMMING HAAS AUTOMATION INC. 2800 Sturgis Road Oxnard, California 93030 Phone: 805-278-1800 www.haascnc.com
More information(Refer Slide Time: 00:50)
Computer Numerical Control of Machine Tools and Processes Professor A Roy Choudhury Department of Mechanical Engineering Indian Institute of Technology Kharagpur Lecture 03 Classification of CNC Machine
More informationG02 CW / G03 CCW Circular Interpolation Motion (Group 01) - Mill
Haas Technical Documentation G02 CW / G03 CCW Circular Interpolation Motion (Group 01) - Mill Scan code to get the latest version of this document Translation Available G02 CW / G03 CCW Circular Interpolation
More informationPreview Sample. Date: September 1, 2010 Author: Matthew Manton and Duane Weidinger ISBN:
Computer Numerical Control Workbook Generic Lathe Published by CamInstructor Incorporated 330 Chandos Crt. Kitchener, Ontario N2A 3C2 www.caminstructor.com Date: September 1, 2010 Author: Matthew Manton
More informationProf. Steven S. Saliterman Introductory Medical Device Prototyping
Introductory Medical Device Prototyping Department of Biomedical Engineering, University of Minnesota http://saliterman.umn.edu/ You must complete safety instruction before using tools and equipment in
More informationProjects. 5 For each component, produce a drawing showing the intersection BO.O. C'BORE 18 DIA x 5 DEEP FROM SECTION ON A - A
Projects ~ Figure Pl Project 1 If you have worked systematically through the assignments in this workbook, you should now be able to tackle the following milling and turning projects. It is suggested that
More informationCNC Programming Guide MILLING
CNC Programming Guide MILLING Foreword The purpose of this guide is to help faculty teach CNC programming without tears. Most books currently available on CNC programming are not only inadequate, but also
More informationControlled Machine Tools
ME 440: Numerically Controlled Machine Tools CNCSIMULATOR Choose the correct application (Milling, Turning or Plasma Cutting) CNCSIMULATOR http://www.cncsimulator.com Teaching Asst. Ergin KILIÇ (M.S.)
More informationComputer Numerical Control (CNC) Hacettepe University Chemical Engineering Department
Computer Numerical Control (CNC) Banu Akar Duygu Gökçe Neşe Kaynak Meltem Erdi Hacettepe University Chemical Engineering Department 22.12.2010 CONTENT 1. What are NC & CNC? 2. History 3. CNC system Elements
More informationMill Series Training Manual. Haas CNC Mill Programming
Haas Factory Outlet A Division of Productivity Inc Mill Series Training Manual Haas CNC Mill Programming Revised 021913 (Printed 02-2013) This Manual is the Property of Productivity Inc The document may
More informationIMPLEMENTATION OF WEB-BASED NC POSTPROCESSOR BUILDER
IMPLEMENTATION OF WEB-BASED NC POSTPROCESSOR BUILDER An NC postprocessor is an automatic manufacturing application program that takes cutter location data in APT syntax obtained from a CAD/CAM system as
More informationLathe Series Training Manual. Haas CNC Lathe Programming
Haas Factory Outlet A Division of Productivity Inc Lathe Series Training Manual Haas CNC Lathe Programming Revised 050914; Rev3-1/29/15; Rev4-31017 This Manual is the Property of Productivity Inc The document
More informationINDIAN INSTITUTE OF TECHNOLOGY KHARAGPUR NPTEL ONLINE CERTIFICATION COURSE. On Industrial Automation and Control
INDIAN INSTITUTE OF TECHNOLOGY KHARAGPUR NPTEL ONLINE CERTIFICATION COURSE On Industrial Automation and Control By Prof. S. Mukhopadhyay Department of Electrical Engineering IIT Kharagpur Topic Lecture
More informationSTATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 223 INTRODUCTION TO COMPUTER NUMERICAL CONTROL
STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 223 INTRODUCTION TO COMPUTER NUMERICAL CONTROL Prepared by: Daniel Miller Updated by: Daniel Miller (April 2015)
More informationWhen the machine makes a movement based on the Absolute Coordinates or Machine Coordinates, instead of movements based on work offsets.
Absolute Coordinates: Also known as Machine Coordinates. The coordinates of the spindle on the machine based on the home position of the static object (machine). See Machine Coordinates Absolute Move:
More informationTable of Contents. Preface 9 Prerequisites 9. Key Concept 1: Know Your Machine From A Programmer s Viewpoint 13. Table of Contents
Preface 9 Prerequisites 9 Basic machining practice experience 9 Controls covered 10 Limitations 10 Programming method 10 The need for hands -on practice 10 Instruction method 11 Scope 11 Key Concepts approach
More information(Refer Slide Time: 01:19)
Computer Numerical Control of Machine Tools and Processes Professor A Roy Choudhury Department of Mechanical Engineering Indian Institute of Technology Kharagpur Lecture 06 Questions MCQ Discussion on
More informationDesign & Manufacturing II. The CAD/CAM Labs. Lab I Process Planning G-Code Mastercam Lathe
2.008 Design & Manufacturing II The CAD/CAM Labs Lab I Process Planning G-Code Mastercam Lathe Lab II Mastercam Mill Check G-Code Lab III CNC Mill & Lathe Machining OBJECTIVE BACKGROUND LAB EXERCISES DELIVERABLES
More informationCOMPUTER INTEGRATED MANUFACTURING LABORATORY (14AME31)
COMPUTER INTEGRATED MANUFACTURING LABORATORY (14AME31) (For III B.Tech - II SEM- Mechanical Engineering) DEPARTMENT OF MECHANICAL ENGINEERING SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY R.V.S
More informationNZX NLX
NZX2500 4000 6000 NLX1500 2000 2500 Table of contents: 1. Introduction...1 2. Required add-ins...1 2.1. How to load an add-in ESPRIT...1 2.2. AutoSubStock (optional) (for NLX configuration only)...3 2.3.
More information1640DCL Digital Control Lathe
1640DCL Digital Control Lathe MACHINE SPECIFICATIONS Multiple Function CNC Lathe 1. Manual Hand wheel Operation 2. CNC G-Code Operation 16.1 swing over bed, 8.6 swing over cross-slide 2.05 diameter hole
More informationMotion Manipulation Techniques
Motion Manipulation Techniques You ve already been exposed to some advanced techniques with basic motion types (lesson six) and you seen several special motion types (lesson seven) In this lesson, we ll
More informationWINMAX LATHE NC PROGRAMMING
WINMAX LATHE NC PROGRAMMING Dual-screen and Max Consoles for Hurco Turning Centers April 2013 704-0115-309 Revision A The information in this document is subject to change without notice and does not represent
More informationSHOP NOTES. GPocket Guide and Reference Charts. for CNC Machinists. Made in the U.S.A.
SHOP NOTES GPocket Guide and Reference Charts for CNC Machinists Made in the U.S.A. WHAT S INSIDE THIS BOOKLET? Decimal Equivalent Chart / Millimeter to Inch Chart Haas Mill G-Codes / Haas Mill M-Codes
More informationLinuxCNC Help for the Sherline Machine CNC System
WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING LinuxCNC Help for the Sherline Machine CNC System LinuxCNC Help for Programming and Running 1. Here is a link
More informationIndex. User Manual. Fadal. Numerics 3 Phase 5% Low 181
Index Numerics 3 Phase 5% Low 181 A A & B Fixtures Offsets 286 A = AUTO 147 A Axis 265 Direction of Motion 265 G90 Absolute Mode 265 G91 Incremental Mode 266 A Axis Brake 268 A Axis Cold Start 266 A Axis
More informationStandard. CNC Turning & Milling Machine Rev 1.0. OM5 Control Software Instruction Manual
Standard CNC Turning & Milling Machine Rev 1.0 OM5 Control Software Instruction Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 Standard CNC Machine 2 Content Warranty and Repair
More informationVMC Series II Vertical Machining Centers PROGRAMMER S MANUAL. Equipped with the Hardinge / Fanuc System II, Fanuc 0i-M, or Fanuc 18-MC Control
PROGRAMMER S MANUAL VMC Series II Vertical Machining Centers Equipped with the Hardinge / Fanuc System II, Fanuc 0i-M, or Fanuc 18-MC Control Revised: July 26, 2004 Manual No. M-377B Litho in U.S.A. Part
More informationLAB MANUAL / OBSERVATION
DHANALAKSHMI COLLEGE OF ENGINEERING DR. VPR NAGAR, MANIMANGALAM, CHENNAI- 601301 DEPARTMENT OF MECHANICAL ENGINEERING LAB MANUAL / OBSERVATION ME6611- CAD/CAM LABORATORY STUDENT NAME REGISTER NUMBER YEAR
More informationGetting Started. Terminology. CNC 1 Training
CNC 1 Training Getting Started What You Need for This Training Program This manual 6 x 4 x 3 HDPE 8 3/8, two flute, bottom cutting end mill, 1 Length of Cut (LOC). #3 Center Drill 1/4 drill bit and drill
More informationHAAS AUTOMATION, INC.
PROGRAMMING WORKBOOK HAAS AUTOMATION, INC. 2800 Sturgis Rd. Oxnard, CA 93030 JANUARY 2005 . JANUARY 2005 PROGRAMMING HAAS AUTOMATION INC. 2800 Sturgis Road Oxnard, California 93030 Phone: 805-278-1800
More informationMilling PCBs. Jonathan Bachrach. September 14, EECS UC Berkeley
Milling PCBs Jonathan Bachrach EECS UC Berkeley September 14, 2016 Last Time 1 PCBs wisegeek Today 2 Milling PCBs CNC 3 Computerized Numeric Control Benefits 4 Automation Precision Repeatability Flexibility
More informationTrade of Toolmaking. Module 6: Introduction to CNC Unit 2: Part Programming Phase 2. Published by. Trade of Toolmaking Phase 2 Module 6 Unit 2
Trade of Toolmaking Module 6: Introduction to CNC Unit 2: Part Programming Phase 2 Published by SOLAS 2014 Unit 2 1 Table of Contents Document Release History... 3 Unit Objective... 4 Introduction... 4
More informationTable 5.1: Drilling canned cycles. Action at the bottom of the hole. Cancels drilling canned cycle Intermittent or continuous feed.
5.18 CANNED CYCLES FOR DRILLING On a lathe, equipped with live tooling (which allows a tool, obviously a drilling or a similar tool, to rotate at the specified RPM, as in a milling machine) and an additional
More informationChapter 14 Automation of Manufacturing Processes and Systems
Chapter 14 Automation of Manufacturing Processes and Systems Topics in Chapter 14 FIGURE 14.1 Outline of topics described in this chapter. Date 1500Ğ1600 1600Ğ1700 1700Ğ1800 1800Ğ1900 Development Water
More informationFigure 1: NC Lathe menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 5 /$7+( 5.1 INTRODUCTION The lathe mode is used to perform operations on 2D geometry, turned on two axis lathes.
More informationApplication Case. Delta Industrial Automation Products for Vertical CNC Machining Centers with Automatic Tool Changers (ATC)
Case Delta Industrial Automation Products for Vertical CNC Machining Centers with Automatic Tool Changers (ATC) Issued by Solution Center Date July, 2014 Pages 5 Applicable to Key words NC311 Series CNC
More informationServomill. Multipurpose Milling Machine Servomill. Conventional Multipurpose Milling Machine.
Multipurpose Milling Machine Conventional Multipurpose Milling Machine for workshop applications, single parts production and training purposes Servo motors and preloaded ball screws on all axes infinitely
More informationWINMAX LATHE NC PROGRAMMING
WINMAX LATHE NC PROGRAMMING Dual-screen and Max Consoles for Hurco Turning Centers March 2012 704-0115-306 Revision A The information in this document is subject to change without notice and does not represent
More informationTechniques With Motion Types
Techniques With Motion Types The vast majority of CNC programs require but three motion types: rapid, straight line, and circular interpolation. And these motion types are well discussed in basic courses.
More informationBHP130Series. Heavy Duty CNC Horizontal Boring & Milling Machines
BHP130Series Heavy Duty CNC Horizontal Boring & Milling Machines BHP130 SERIES CNC Heavy Duty Horizontal Boring and Milling Machines SNK Nissin BHP130 Boring Mills have the power and robust construction
More informationMill OPERATING MANUAL
Mill OPERATING MANUAL 2 P a g e 7/1/14 G0107 This manual covers the operation of the Mill Control using Mach 3. Formatting Overview: Menus, options, icons, fields, and text boxes on the screen will be
More informationFixed Headstock Type CNC Automatic Lathe
Fixed Headstock Type CNC Automatic Lathe GTY Configured with two spindles, one turret, 2 x Y axes, gang tools and X3 axis to back spindle, the BNA42GTY can mount up to 45 tools. 3 tool simultaneous cutting
More informationCNC Lathe Programming-Basic
Western Technical College 31420312 CNC Lathe Programming-Basic Course Outcome Summary Course Information Description Career Cluster Instructional Level Total Credits 1.00 An introduction to planning and
More informationINDEX A FAGOR. 1. MC Training Manual. 2. Additional Simple Cycles. 3. USB Interface. 4. Installation. 5. Electrical Drawings
KNEE MILL PACKAGE INDEX 1. MC Training Manual 2. Additional Simple Cycles 3. USB Interface 4. Installation 5. Electrical Drawings 1 800 4A FAGOR * This information package also includes 8055 CNC Training
More informationProf. Steven S. Saliterman Introductory Medical Device Prototyping
Introductory Medical Device Prototyping Department of Biomedical Engineering, University of Minnesota http://saliterman.umn.edu/ Images courtesy of Haas You must complete safety instruction before using
More informationCobra Series CNC Lathes
PROGRAMMER S MANUAL TP1480B TP3264 TP2580 Cobra Series CNC Lathes Equipped with the GE Fanuc 21T Control Manual No. M-312C Litho in U.S.A. Part No. M C-0009500-0312 October, 1998 - NOTICE - Damage resulting
More informationThe enriched system configuration designed based on the loader head accommodates a wide range of automation needs.
CNC Lathe These are high-precision chucking machines equipped with a general-purpose in-machine loader head. The loading time is shortened substantially through coordinated operation of the loader head
More informationEFFECTS OF INTERPOLATION TYPE ON THE FEED-RATE CHARACTERISTIC OF MACHINING ON A REAL CNC MACHINE TOOL
Engineering MECHANICS, Vol. 19, 2012, No. 4, p. 205 218 205 EFFECTS OF INTERPOLATION TYPE ON THE FEED-RATE CHARACTERISTIC OF MACHINING ON A REAL CNC MACHINE TOOL Petr Vavruška* The article is focused on
More informationEASY CNC. Table of Contents
Square 1 Electronics announces its new book by David Benson, "Easy CNC", A Beginner's Guide to CNC" The complete table of contents follows: This book was written by David Benson (8-1/2 x 11", 200 pages,
More informationCAD/CAM Software & High Speed Machining
What is CAD/CAM Software? Computer Aided Design. In reference to software, it is the means of designing and creating geometry and models that can be used in the process of product manufacturing. Computer
More informationMachinist--Cert Students apply industry standard safety practices and specific safety requirements for different machining operations.
MTT Date: 09/13/2018 TECHNOLOGY MTT Machine Tool Technology--AA Students apply industry standard safety practices and specific safety requirements for different machining operations. Students calculate
More informationA Build-Your-Own Open Source CNC Lathe Machine
A Build-Your-Own Open Source CNC Lathe Machine Fabrication and User manual MHRD Teaching Learning Centre for Design and Manufacturing Indian Institute of Information Technology for Design and Manufacturing
More informationENGI 7962 Mastercam Lab Mill 1
ENGI 7962 Mastercam Lab Mill 1 Starting a Mastercam file: Once the SolidWorks models is complete (all sketches are Fully Defined), start up Mastercam and select File, Open, Files of Type, SolidWorks Files,
More informationFeaturing ProtoTRAK CNCs. Introducing. TRAK DPMRX Bed Mills. Featuring the NEW. ProtoTRAK RMX
Featuring ProtoTRAK CNCs Introducing TRAK DPMRX Bed Mills Featuring the NEW ProtoTRAK RMX TRAK Featuring the amazing new ProtoTRAK RMX CNC DPMRX Bed Mills Touchscreen for an extraordinary user experience
More informationUser's Guide. Servo CNC System. for Windows Programming and Operation. SW Version 5.0 Manual Version 1.1b. Form
User's Guide Servo CNC System for Windows Programming and Operation SW Version 5.0 Manual Version 1.1b Form 0800-80821 Copyright 2006 ServoSource. All rights reserved The software contains proprietary
More informationFixed Headstock Type CNC Automatic Lathe
Fixed Headstock Type CNC Automatic Lathe MSY The BNE series is renowned for its high rigidity, heavy cutting capability and outstanding precision. The new MSY model extends the ability of the BNE series
More information[ means: One-stop shop. EMCOMAT FB-450 L / FB-600 L. Universal milling machines with Heidenhain TNC 320 or EMCO Easy Cycle
[ E[M]CONOMY] means: One-stop shop. EMCOMAT FB-450 L / FB-600 L Universal milling machines with Heidenhain TNC 320 or EMCO Easy Cycle EMCOMAT FB-450 L / FB-600 L Whether single or small series production,
More informationMachine Tool Technology/Machinist CIP Task Grid
1 100 ORIENTATION / SAFETY 101 Describe the Occupational Safety and Health Administration (OSHA) and its role in the machining industry. 102 Identify & explain safety equipment and procedures. 103 Identify
More informationCNC LATHE TURNING CENTER PL-20A
CNC LATHE TURNING CENTER PL-20A CNC LATHE TURNING CENTER For High Precision, High Speed and High Productivity MAIN FEATURE Introducing the latest and strongest CNC Lathe PL20A that has satisfied the requirements
More informationTable of Contents. Table of Contents. Preface 11 Prerequisites... 12
Table of Contents Preface 11 Prerequisites... 12 Basic machining practice experience... 12 Controls covered... 12 Limitations... 13 The need for hands -on practice... 13 Instruction method... 13 Scope...
More informationTIMTOS 2017 EXHIBITS PROFILE
TIMTOS 2017 EXHIBITS PROFILE Product Code Product Name METAL CUTTING MACHINE TOOL Lathes and Turning Machines 160101 Lathes, Swiss Type 160502 Bench Lathes 160503 High Speed Lathes 160504 Automatic Lathes
More informationCNC Machinery. Module 5: CNC Programming / Milling. IAT Curriculum Unit PREPARED BY. August 2009
CNC Machinery Module 5: CNC Programming / Milling PREPARED BY IAT Curriculum Unit August 2009 Institute of Applied Technology, 2009 ATM313-CNC Module 5: CNC Programming / Milling Module Objectives: 1.
More informationHAAS AUTOMATION, INC. PROGRAMMING MILL SERIES WORKBOOK ANSWERS HAAS AUTOMATION, INC STURGIS ROAD OXNARD, CA
HAAS AUTOMATION, INC. MILL SERIES PROGRAMMING WORKBOOK HAAS AUTOMATION, INC. 2800 STURGIS ROAD OXNARD, CA 93030 www.haascnc.com 800-331-6746 ANSWERS PROGRAMMING HAAS AUTOMATION INC. 2800 Sturgis Road Oxnard,
More informationFigure 1: NC EDM menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 6 :,5(('0 6.1 INTRODUCTION SURFCAM s Wire EDM mode is used to produce toolpaths for 2 Axis and 4 Axis EDM machines.
More informationModule 2. Milling calculations, coordinates and program preparing. 1 Pepared By: Tareq Al Sawafta
Module 2 Milling calculations, coordinates and program preparing 1 Module Objectives: 1. Calculate the cutting speed, feed rate and depth of cut 2. Recognize coordinate 3. Differentiate between Cartesian
More informationSAMSUNG Machine Tools PL 1600G/1600CG GANG CNC TURNING CENTER
SAMSUNG Machine Tools PL 1600G/1600CG GANG CNC TURNING CENTER SAMSUNG Machine Tools GANG CNC TURNING CENTER PL 1600G/1600CG Best fit on Both High Speed Machining and Automation System. Automation Ready
More informationPro/NC. Prerequisites. Stats
Pro/NC Pro/NC tutorials have been developed with great emphasis on the practical application of the software to solve real world problems. The self-study course starts from the very basic concepts and
More informationMachinist NOA (1998) Subtask to Unit Comparison
Machinist NOA (1998) Subtask to Unit Comparison NOA Subtask Task 1 Demonstrates safe working practices. 1.01 Recognizes potential health and safety hazards. A1 Safety in the Machine Shop 1.02 Recognizes
More informationTutorial 4 - Open Dxf file and create multiple toolpaths (Contour, Pocket and Drill).
Tutorial 4 - Open Dxf file and create multiple toolpaths (Contour, Pocket and Drill). In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part, another toolpath
More informationMultipurpose Milling Machine Servomill 700. Conventional Multipurpose Milling Machine.
Multipurpose Milling Machine Conventional Multipurpose Milling Machine For workshop application, single parts production and training purposes Servo motors and preloaded ball screws on all axes Infinitely
More informationSUMMARY. Valves, pipes and manifold-type parts are ideal candidates for Turn-Cut.
SUMMARY Turn-Cut is a programming option available on Okuma horizontal machining centers that allows the machine to create bores and diameters that include circular and/or angular features. It allows users
More informationLathe Series Training Manual. Live Tool for Haas Lathe (including DS)
Haas Factory Outlet A Division of Productivity Inc Lathe Series Training Manual Live Tool for Haas Lathe (including DS) Created 020112-Rev 121012, Rev2-091014 This Manual is the Property of Productivity
More informationMTC200 Description of NC Cycles. Application Manual SYSTEM200 DOK-MTC200-CYC*DES*V22-AW02-EN-P
X rapid feed feed first feed * n... appr.. * appr.. * 1... end point Z gradient starting point Z end p. X start. p. X Z MTC200 Description of NC Cycles Application Manual SYSTEM200 About this Documentation
More informationHigh Precision CNC Lathe
High Precision CNC Lathe Designed for high-precision machining of smalldiameter workpieces, this machine has a wing type fixed spindle for low thermal influence installed on a thermally symmetrical machine
More informationConversational Programming. Alexsys Operator Manual
Conversational Programming Alexsys Operator Manual Alexsys Operator Manual 1. Overview ALEXSYS is a programming system for CNC machining centers. That combines features of CAD / CAM systems with typical
More informationSprutCAM. CAM Software Solution for Your Manufacturing Needs
SprutCAM SprutCAM is is a CAM system for for NC NC program program generation for machining using; multi-axis milling, milling, turning, turn/mill, turn/mill, Wire Wire EDM numerically EDM numerically
More informationBHARATHIDASAN ENGINEERING COLLEGE NATTRAMPALLI DEPARTMENT OF MECHANICAL ENGINEERING LABORATORY MANUAL ME6411-MANUFACTURING TECHNOLOGY LAB- II
BHARATHIDASAN ENGINEERING COLLEGE NATTRAMPALLI 635 854 DEPARTMENT OF MECHANICAL ENGINEERING LABORATORY MANUAL ME6411-MANUFACTURING TECHNOLOGY LAB- II YEAR / SEMESTER : II / IV DEPARTMENT : Mechanical REGULATION
More informationHIGH PERFORMANCE TRAVELING COLUMN VERTICAL MACHINING CENTER
HIGH PERFORMANCE TRAVELING COLUMN VERTICAL MACHINING CENTER 1 With the installation of dividing wall in the working area, the TCV series can implement machining and set up workpiece simultaneously. It
More informationCincom Evolution Line
Efficient Production Impressive Value Cincom Evolution Line Sliding Headstock Type Automatic CNC Lathe Cincom Evolution line from Citizen Introducing the K16E faster processing with outstanding ease-of-use.
More information6000 CNC CONTROL HELP MENU S
6000 CNC CONTOL HEL MENU S The HEL MENU S are access by pressing. This can be done from either Manual or Edit. F1 HEL Manual mold soft keys Edit mold soft keys First Help screen Note: The center of the
More informationMiyano Evolution Line
Evolution Line CNC Turning center with 2 spindles, 2 turrets and 1 -axis slide BNJ-34/42/51 "Evolution and Innovation" is the Future What could not be done can be done. -axis movement is added to the traditional
More informationPROGRAMMER S MANUAL CNC Lathes Equipped with the GE Fanuc 18T Control
PROGRAMMER S MANUAL TP1421 CNC Lathes Equipped with the GE Fanuc 18T Control Revised: September 28, 1999 Manual No. M-320A Litho in U.S.A. Part No. M A-0009500-0320 April, 1997 - NOTICE - Damage resulting
More informationBIG IDEAS. Personal design interests require the evaluation and refinement of skills. Learning Standards
Area of Learning: APPLIED DESIGN, SKILLS, AND TECHNOLOGIES BIG IDEAS Design for the life cycle includes consideration of social and environmental impacts. Personal design interests require the evaluation
More informationInterruptions caused by, for example, tool breakage (or tool change, or checking the parts), would not affect the position at the interruption.
Incremental and Absolute systems CNC systems are further divided into incremental and absolute systems (Figure 8). In incremental mode, the distance is measured from one point to the next. For example,
More informationUser s Manual Cycle Programming TNC 320. NC Software
User s Manual Cycle Programming TNC 320 NC Software 340 551-04 340 554-04 English (en) 9/2009 About this Manual The symbols used in this manual are described below. This symbol indicates that important
More information