A NEW GYMNASIUM AT ARITON SCHOOL FOR THE DALE COUNTY BOARD OF EDUCATION OZARK, ALABAMA

Transcription

1 McKee and ssociates rchitecture and Interior Design ddendum No. ONE Date: Project: NEW GYMNSIUM T RITON SCHOOL FOR THE DLE COUNTY BORD OF EDUCTION OZRK, LBM. GENERL PROJECT NO BC # The following changes and/or substitutions to the plans and specifications are hereby made a part of same and are incorporated in full force as part of the contract. B. Bidders shall acknowledge receipt of this ddendum in writing on his Proposal Form. C. The following General Contractors have pre-qualified to bid this project: nderson Construction Fort Gaines, G Bullard Cook Montgomery, L Diversified General Contractors Opp, L Enco Construction Enterprise, L First Team Construction uburn, L South Hull Street Montgomery, labama

2 .2 SPECIFICTIONS Hughes Construction Ozark, L Wyatt Sasser Construction ndalusia, L Refer to Section 02720, Storm Sewers: Delete the following: Downspout Boots: Provide PVC, Schedule 80 downspout boot, 40 long, connect to metal downspouts and run drain line to storm sewer line as indicated on the drawings. Paint as required. B. See the attached Section 08700, Finish Hardware (Revised ) herein. C. See the attached Section 000, Ball Stop Netting and Detail herein. D. The following manufactures are hereby approved subject to the plans and specifications: Section 0800, Steel Doors and Frames: Republic Door and Frames Section 09550, Gymnasium Wood Flooring: Connor Sports Flooring Rezill Panel Section 0500, thletic Metal Lockers: Lyon Workspace Section 0530, luminum Hanger Rod Canopy: Mitchell Metals Section 200, Gymnasium Equipment: rizona Courtlines Inc Performance Sports Systems Draper thletic Equipment Section 2700, Telescopic Gymnasium Seating: Irwin Seating Company Interkal Seating Section 320, Pre-Engineered Buildings: CI Building Systems Section 3670, Extruded luminum Walkway Covers: Mitchell Metals 63 South Hull Street Montgomery, labama

3 .3 DRWINGS. Refer to Sheet 7., Door Schedule: Delete refences to Doors 4a and 9a B. See the attached Revised Drawings as follows: Sheet S. (09.8.7) Sheet S.3 (09.8.7) Sheet S3.2 (09.8.7) Sheet.3 ( ) END OF DDENDUM ONE 63 South Hull Street Montgomery, labama

4 SECTION FINISH HRDWRE (REVISED ) PRT GENERL RELTED DOCUMENTS Drawings and general provisions of Contract including General and Supplementary Conditions and Division Specification Sections apply to this Section. SUMMRY This Section includes items known commercially as finish or door hardware that are required for swing, sliding, and folding doors, except special types of unique hardware specified in the same sections as the doors and door frames on which they are installed. This Section includes the following:. Hinges 2. Continuous Geared Hinges 3. Lock Cylinders and Keys 4. Key Control System. 5. Lock and Latch Sets. 6. Exit Devices 7. Surface Closers 8. Overhead Stops and Holders 9. Push/Pulls, Protection Plates 0. Threshold, Weatherstrpping, and Gasketing Related Sections: The following Sections contain requirements that relate to this Section:. Division 8 Section "Standard Steel Doors and Frames" for silencers integral with hollow metal frames. 2. Division 8 Section "Flush Wood Doors" for factory pre-fitting and factory premachining of doors for door hardware. 3. Division 8 Section "luminum Entrances and Storefronts" for aluminum entrance door hardware. HRDWRE LLOWNCE llowance of $, for Certified (must be current in the CEP program per DHI & all documents certified using current seal showing certification) HC (rchitectural Hardware Consultant) & FDI (Fire Door ssembly Inspector document of certification from DHI must be provided) to visit job site upon substantial completion as directed by 7-57 FINISH HRDWRE (REVISED )

5 rchitect. written report will be required for the Owner, rchitect, and Contractor Door hardware supplier's responsibilities shall be as follows:. Submittals: Submit through Contractor required product data, final hardware schedule; separate keying schedule, and samples as specified in this Section, unless otherwise indicated. 2. Construction Schedule: Inform Contractor promptly of estimated times and dates that will be required to process submittals, to furnish templates, to deliver hardware, and to perform other work associated with furnishing door hardware for purposes of including this data in construction schedule. Comply with this schedule. 3. Coordination and Templates: ssist Contractor as required to coordinate hardware with other work in respect to both fabrication and installation. Furnish Contractor with templates and deliver hardware to proper locations. 4. Product Handling: Package, identify, deliver, and inventory door hardware specified in this Section. 5. Discrepancies: Based on requirements indicated in Contract Documents in effect at time of door hardware selection, furnish types, finishes, and quantities of door hardware, including fasteners, and Owner's maintenance tools required to comply with specified requirements and as needed to install and maintain hardware. Furnish or replace any items of door hardware resulting from shortages and incorrect items at no cost to the Owner or Contractor. Obtain signed receipts from Contractor for all delivered materials. Contractor's responsibilities shall be as follows:. Submittals: Coordinate and process submittals for door hardware in same manner as submittals for other work. 2. Construction Schedule: Cooperate with door hardware supplier in establishing scheduled dates for submittals and delivery of templates and door hardware. Incorporate in construction schedule the times and dates related to furnishing hardware by door hardware supplier. 3. Coordination: Coordinate door hardware with other Work. Furnish hardware supplier or manufacturer with shop drawings of other work where required or requested. Verify completeness and suitability of hardware with supplier. 4. Product Handling: Provide secure lock-up for hardware delivered to the site. Inventory hardware jointly with representative of hardware supplier and issue signed receipts for all delivered materials. 5. Installation Information: The general types and approximate quantities of hardware required for this Project are indicated at the end of this Section in order to establish Contractor's costs for installation and other work not included in allowance FINISH HRDWRE (REVISED )

6 6. No adjustments in Contract sum will be made for costs other than those covered by the allowances for subsequent increases or decreases in quantity of one or more hardware types that do not exceed 5 percent. SUBMITTLS General: Submit the following in accordance with Conditions of Contract and Division Specification sections. Product data including manufacturers' technical product data for each item of door hardware, installation instructions, maintenance of operating parts and finish, and other information necessary to show compliance with requirements. Final hardware schedule coordinated with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.. Upon return of the reviewed finish hardware schedule, arrange for a meeting with the Owner and representatives of rchitect. keying schedule will be established and submitted to the rchitect and Owner. fter review, the keying schedule will be returned to representatives of Finish Hardware Supplier so that permanent cylinders and keys can be prepared on a timely basis. QULITY SSURNCE Single Source Responsibility: Obtain each type of hardware (latch and lock sets, hinges, closers, etc.) from a single manufacturer. Supplier Qualifications: recognized architectural door hardware supplier, with warehousing facilities in the Project's vicinity, that has a record of successful in-service performance for a minimum of 0 years, for supplying door hardware similar in quantity, type, and quality to that indicated for this Project and that employs an experienced Certified architectural hardware consultant (HC) and is current with CEP program with Door and hardware Institute (DHI) all submittals will require a current certification seal of HC who is available to Owner, rchitect, and Contractor, at reasonable times during the course of the Work, for consultation. Fire-Rated Openings: Provide door hardware for fire-rated openings that complies with NFP Standard No. 80 and requirements of authorities having jurisdiction. Provide only items of door hardware that are listed and are identical to products tested by UL, Warnock Hersey, FM, or other testing and inspecting organization acceptable to authorities having jurisdiction for use on types and sizes of doors indicated in compliance with requirements of fire-rated door and door frame labels FINISH HRDWRE (REVISED )

7 PRODUCT HNDLING Tag each item or package separately with identification related to final hardware schedule, and include basic installation instructions with each item or package. Packaging of door hardware is responsibility of supplier. s material is received by hardware supplier from various manufacturers, sort and repackage in containers clearly marked with appropriate hardware set number to match set numbers of approved hardware schedule. Two or more identical sets may be packed in same container. Inventory door hardware jointly with representatives of hardware supplier and hardware installer until each is satisfied that count is correct. Deliver individually packaged door hardware items promptly to place of installation (shop or Project site). Provide secure lock-up for door hardware delivered to the Project, but not yet installed. Control handling and installation of hardware items that are not immediately replaceable so that completion of the Work will not be delayed by hardware losses both before and after installation. MINTENNCE Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of door hardware. PRT 2 PRODUCTS CCEPTBLE MNUFCTURERS Hinges Hager Companies Bommer Industries, Inc. STNLEY Hinges. Provide only template produced units 2. Provide Phillips flat-head or machine screws for installation of units, except furnish Phillips flat-head wood screws for installation of units in to wood. Finish screw heads to match surface of hinges or pivots. 3. Hinge pins, except as noted, are to be provided as follows: a. Steel Hinges: Steel pins b. Non-ferrous Hinges: Stainless steel pins 7-57 FINISH HRDWRE (REVISED )

8 c. Exterior Doors: Use Non Removable Pins d. Interior Doors: Non-rising pins e. Electric Hinges: Non-removable pins 4. Tips shall be flat button and matching plug, finished to match leaves. 5. Provide number of hinges indicated but not less than three (3) hinges for door leaf of 90 or less in height and one additional hinge for each 30 of additional height. 6. Provide ball bearing hinges of the type and weight suggested by the hinge manufacturer for each type of door application. Continuous Geared Hinges: Hager Companies / Roton BH Manufacturing SELECT Products Ltd STNLEY Hinges. Fully Concealed Hinges, Heavy Duty 2. Conform to NSI/BHM Grade. 3. Typical hinge height shall be " less than nominal door height. Lock Cylinders & Keying: Cylinders shall be Owners existing system Sargent RN no exception. ll Locks shall be keyed to this system.. ll cylinders shall be keyed into a new grand master system as directed by the owner. 2. Keying Meeting between Owner, rchitect, and Hardware Supplier will be required to determine Owners Request for keying of all cores/cylinders, keys, etc. 3. Keys shall be furnished per the following: a. Minimum of (2) two operating cut keys per change. b. Minimum of (3) master keys per master system. c. Minimum of (2) control keys. 4. Supply a Key Cabinet with capacity of plus 50% of keys required equal to MMF Industries FINISH HRDWRE (REVISED )

9 Locksets & Latch-sets: STNLEY / Best ccess Systems - 40H Series x 5J Design Schlage - L9000 Series x 06L Design DORM - M9000 Series x LRH Design. Locksets and latch-sets of all manufacturers must conform to the requirements of Subparagraphs 2 and, and be approved by the rchitect. 2. Mortise Type a. Locksets and latch sets must conform to NSI 56.2 Series 000, Grade, and be UL Listed b. Locksets and latch-sets must be heavy duty mortise type with 2-3/4 in. backset, or greater as specified, with a 3/4 inch throw latch-bolt. c. Locksets shall be furnished with a cylinder housing that accepts a small format interchangeable core. d. Trim to be equal to Dorma LRH Design with an antimicrobial coating ('M') Exit Devices: DORM Series x YR Design STNLEY / Precision Hardware - pex Series x 4900 Design Von Duprin - 98 Series x Escutcheon 06 Lever Design. ll exit devices to be of one manufacturer and provided in same finish (630 M) and lever design as Locksets. 2. Provide sex nuts and bolts for attachment of surface applied items to doors. 3. Devices shall be UL listed. Devices for fire rated openings shall bear factory installed UL markings that indicate approval for fire rated openings. 4. ll exit devices shall be touch-bar type design and Grooved aluminum extrusions are not allowed. 5. ll exit devices shall comply with NSI 56.3, Grade. 6. Exit devices must meet hurricane code where required. 7. Exit device trim shall be equal to Dorma YR design with an antimicrobial coating ('M') 7-57 FINISH HRDWRE (REVISED )

10 Surface Closers: DORM Series LCN - 40 Series STNLEY Closers - D-4550/ Series. Size of units: Except as otherwise specifically indicated, comply with the manufacturer s recommendations for size of door control unit, depending upon size of door, exposure to weather and anticipated frequency of use. a. Where parallel arms are indicated for closers, provide closer unit one size larger than recommended for use with standard arms. b. Where manual closers are indicated for doors required to be accessible to the physically handicapped, provide adjustable units, NSI opening force and delayed action closing. 2. Provide manual closers that are certified to exceed ten million (0,000,000) full load operating cycles by a recognized independent testing laboratory. Closers are to be fully hydraulic, rack and pinion action with high strength cast aluminum or cast iron cylinders and one piece forged steel pistons. Hydraulic fluid to be of a type requiring no seasonal adjustments for temperature. Hydraulic regulation to be controlled by tamper-proof, noncritical screw values, adjustable with a hex by tamper-proof, non-critical screw valves, adjustable with a hex wrench. Separate adjustments for back check, general speed, and latch speed. Where detailed on double lever arm closers, provide a delayed action feature to delay closing up to one minute for maximum opening to approximately 75 degrees. Back check shall be properly located for protection of the door, frame and applied hardware. 3. Use of closers with built-in spring or cushion stops will be allowed in lieu of overhead stops. 4. ll door closers shall comply with NSI 56.4 Grade and meet the standards of NSI 7. for barrier-free accessibility. Overhead Stops and Holders: DORM BH Manufacturing Hager Companies. Conform to NSI 56.8 Grade. 2. Surface Mount, Heavy or Medium Duty (refer to hardware sets) 7-57 FINISH HRDWRE (REVISED )

11 Push/Pulls, Protection Plates: Hager Companies Rockwood Manufacturing Co. Burns Manufacturing, Inc.. Provide manufacturers standard exposed fasteners for installation, through bolted for matched pairs, but not of single units. 2. Provide 6 gauge minimum thickness for plates. 3. Where specified in the schedule, push/pulls shall have an antimicrobial coating. Threshold, Weather-stripping & Gasketing: Zero International Hager Companies National Guard Products, Inc. FINISHES. Provide continuous weather-stripping at each edge of every exterior door leaf, except as otherwise indicated. 2. Provide type, size and profile shown as scheduled. 3. Provide non-corrosive fasteners as recommended by manufacturer for application indicated. Do not specify adhesive backed weather-strip or gasket material. 4. Where replaceable seal strips are scheduled, provide only those units where resilient or flexible seal strip is easily replaceable from stocks maintained by manufacturer. 5. Proved standard metal threshold unit of type, size and profile shown as scheduled. Provide as indicated in the hardware schedule and as previously noted herein. PRT 3 EXECUTION INSTLLTION Install each hardware item in compliance with manufacturer s instructions and recommendations. Where cutting and fitting is required to install hardware onto or into surfaces that are later to be painted of finished in another way, install each item completely and then remove and store in a secure place during the finish application. fter completion of the finishes, reinstall each item FINISH HRDWRE (REVISED )

12 . Do not install surface mounted items until finishes have been completed on the substrate. Conform to NSI 7. for positioning requirements for the handicapped. PROTECTION & CLENING fter installation, clean metal surfaces on both interior and exterior of all mortar, paint and other contaminants. fter cleaning, protect work against damage. FINL DJUSTMENT Whenever hardware is installed more than one month prior to occupancy or acceptance, return during the week prior to acceptance or occupancy and make a final inspection and adjustment of all hardware items in such space or area. SCHEDULE HRDWRE SET 0 Door # 0a, 0b 2 Hinge, 303G HD X 83" CONCELED LEF CYLINDER S REQUIRED 3 IC Core CORE S REQUIRED Conc V-Rod CD 900 B NO TRIM LHR X 630M 630M Conc V-Rod CD 900 B NO TRIM F03 RHR X 630M 630M 2 Closer 896 DS8 TPK89 SN LUM Drop Plate DP 89 DROP PLTE HD Spacer BSHD SPCER Offset Pull 2J - 0" CTC X TB 630 T/Hold 520 SV - 72" 628 * by others * PERIMETER SEL BY OTHERS * by others * STRGL BY OTHERS * by others * SWEEP STRIP BY OTHERS 7-57 FINISH HRDWRE (REVISED )

13 HRDWRE SET 02 Door # 04, 05 3 Hinge 8 BB X 4.5 US26D 652 Closer C F89 TPK89 SN REG RM LESS P 689 Kick Plate 90 S 8 X " US32D, J Wall Stop 236 W US32D (CONCVE TYPE), L Mop Plate 90 S 6 X " 630 M Pull Plate 33 E 4 X 6, 630 MV3, GION (M) 630M M Push Plate 30 S 8 X 6, 630 MV3, GION (M) 630M 3 Silencer 307 D METL FRME, L030 GREY HRDWRE SET 03 Door # 02a, 02b Padlock 4B L 606 IC Core CORE S REQUIRED Hardware Set # 03 Notes: Balance of hardware shall be furnished by the counter shutter manufacturer. HRDWRE SET 04 Door # 02 3 Hinge 82 BB X 4.5 NRP US26D 652 IC Core CORE S REQUIRED Classrm F05 M9070 J LRH US32D M 630M Closer C F89P P TPK89 SN 689 Floor Stop 24 F US26D, L Silencer 307 D METL FRME, L030 GREY HRDWRE SET 05 Door # 07 6 Hinge 82 BB X 4.5 NRP US26D 652 IC Core CORE S REQUIRED Storeroom DB M9980 J LRH 630M 630M 2 Closer C DS7 TPK86 SN COV LUM Flushbolt 282D - 2" UL US26D, L Dust Proof Stk 280X WS RP US26D, L Silencer 307 D METL FRME, L030 GREY 7-57 FINISH HRDWRE (REVISED )

14 HRDWRE SET 06 Door # 0c, 0d 6 Hinge 8 BB X 4.5 US26D CYLINDER S REQUIRED 3 IC Core CORE S REQUIRED Exit CD 9400 LBR X YR08 LC 630 M RHR 630M Exit CD 9400 LBR X YR08 LC 630 M RHR 630M 2 Closer 896 S-DST TPK89 SN LUM Kick Plate 90 S 8 X " US32D Silencer 307 D METL FRME, L030 GREY HRDWRE SET 07 Door # 08, 9b Hinge, 303G HD X 83" CONCELED LEF CYLINDER S REQUIRED 2 IC Core CORE S REQUIRED Rim Exit F08 CD 9300 B YR08C X 630M 630M Closer 896 S DS8 TPK89 SN LUM 689 Kick Plate 90 S 8 X " US32D, J Sweep 750 SN - 36" 628 W/Strip 89 SV - 7' (@36", 2@84"), R3Y T/Hold, J S 36" X WS, J Drip Strip 80S - 40" 628 HRDWRE SET 08 Door # 03, 03b, 05b, 05c, 0, 5 3 Hinge 82 BB X 4.5 NRP US26D 652 IC Core CORE S REQUIRED Storeroom F07 M9080 J LRH US32D M 630M Closer 896 DS8 TPK89 SN LUM 689 Kick Plate 90 S 8 X " US32D, J Silencer 307 D METL FRME, L030 GREY 7-57 FINISH HRDWRE (REVISED )

15 HRDWRE SET 09 Door #, 3, 4, 6, 8, 9 3 Hinge 82 BB X 4.5 US26D 652 IC Core CORE S REQUIRED Classrm F05 M9070 J LRH US32D M 630M Closer C RP COV SN TPK86 P RM 689 Kick Plate 90 S 8 X " US32D, J Wall Stop 236 W US32D (CONCVE TYPE), L Silencer 307 D METL FRME, L030 GREY HRDWRE SET 0 Door # N Hinge, 303G HD X 72" CONCELED LEF 628 Privacy F22 M9040 LRH US32D M 630M Wall Stop 236 W US32D (CONCVE TYPE), L Silencer 307 D METL FRME, L030 GREY HRDWRE SET Door # 09 Hinge, 303G HD X 83" CONCELED LEF 628 IC Core CORE S REQUIRED Storeroom DB M9980 J LRH 630M 630M Closer 896 S DS8 TPK89 SN LUM 689 Sweep 750 SN - 36" 628 W/Strip 89 SV - 7' (@36", 2@84"), R3Y T/Hold, J S 36" X WS, J Drip Strip 80S - 40" 628 HRDWRE SET 02 Door # 06a, 06b 2 Hinge, HD X 83" CONCELED CYLINDER S REQUIRED 4 IC Core CORE S REQUIRED Mullion 340KR X 96" LESS MORTISE CYL 600 Rim Exit F08 CD 9300 B YR08C X 630M 630M Rim Exit F02 CD 9300 B YR02R LC X 630M 630M 7-57 FINISH HRDWRE (REVISED )

16 2 Closer 896 S DS8 TPK89 SN LUM Kick Plate 90 S 8 X " US32D, J Sweep 750 SN - 36" 628 W/Strip 89 SV - 20' (@72", 2@84"), 628 T/Hold, 42 S 72" X WS, J Drip Strip 80S - 76" 628 Mull Seal HH SEL 86" 628 Hardware Set 03 Door # 03 2 Cont Hinges 662HD Mort Cyl E Mort Exit 2303 x Closers CL D-455 CS x SN Flushbolt 282D - 2" UL 626 Threshold 896S x LR 628 Set W/S 60S LR 628 stragal BY DOOR MFGR. END OF SCHEDULE (REVISED ) 7-57 FINISH HRDWRE (REVISED )

17 SECTION 000 BLL STOP NETTING PRT GENERL RELTED DOCUMENTS: Drawings and general provisions of Contract including General and Supplementary Conditions and Division Specification Sections apply to work of this section. SUMMRY Provide all equipment and materials, and do all work necessary to furnish and install the athletic equipment, as indicated on the drawings and as specified herein. thletic equipment shall include, but not be limited to:. Football Safety Ball Stop Netting System SUBMITTLS Shop drawings shall indicate the model number, type of material, finishes, attachments and details of construction. Submit color samples and warranties as specified. RELTED WORK Examine contract documents for requirements that affect work of this section. Other specification sections that directly relate to the work of this section include, but are not limited to:. Section Synthetic Field Surfacing REFERENCES Comply with applicable requirements of the following standards. Where these standards conflict with other specified requirements, the most restrictive requirements shall govern.. National Federation of State High School ssociations (NFHS) 2. National Collegiate thletic ssociation (NC) 3. International mateur thletic ssociation (IF) 4. merican Sports Builders ssociation (SB) 5. Manufacturers Data and Recommended Installation Requirements 7-57 BLL STOP NETTING 000 -

18 SUBMITTLS Shop drawings shall indicate the model number, type of material, finishes, attachments and details of construction. Submit color samples and warranties as specified. PRODUCT DELIVERY ND STORGE Materials delivered to the site shall be examined for damage or defects in shipping. ny defects shall be noted and reported to the Owners representative. Replacements, if necessary, shall be immediately re-ordered, so as to minimize any conflict with the construction schedule. Sound materials shall be stored above ground under protective cover or indoors so as to provide proper protection. WRRNTY Provide manufacturer s standard warranty on all sports & physical education equipment from the date of substantial completion as stated in this specification. PRT 2 PRODUCTS BLL STOP NETTING ND POSTS: Manufacturers: The following manufacturers' products have been used to establish minimum standards for materials, workmanship and function: Promats thletics, Salisbury, NC Model FSNS85040 Equal products of other manufacturers may be used in the work provided such products have been approved by the rchitect, not less than five (5) days prior to scheduled bid opening. MTERILS Equipment shall be provided complete as per manufacturer's standard catalog description and specifications for the numbers indicated in the schedule. Equipment that is to be permanently installed shall be complete and ready for use BLL STOP NETTING 000-2

19 SFETY NETTING ND POSTS s manufactured by Promats thletics, Salisbury, NC Model FSNS85040, consisting of #8 standard weight nylon netting, 4 square, UV stabilized and heat set weather protective coating, color black, sewn rope binding, 5 high x 40 wide. To be mounted on schedule 40 steel pipes (8.625 OD). The poles shall have internal reinforcement at stress points and welded on rope tie-offs. Ground sleeves shall be 0 ¾ x 3/6 galvanized steel tubes, 60 long. See attachment at the end of this section. PRT 3 EXECUTION PREPRTION Make such arrangements as are necessary to provide scaffolding to perform work under this Section. Damage to equipment, and the like shall be corrected at the expense of the Contractor under this Section. INSTLLTION Install equipment in accordance with the manufacturer's printed instructions, drawings, and specifications, and approved shop drawings. Loose equipment shall be removed from packaging or crating, cleaned, and tested for proper operation before turning over to Owner. DEMONSTRTION Work under this Section shall include demonstrating the proper use and operation of equipment to the Owner as may be required. END OF SECTION BLL STOP NETTING 000-3

20 Minimum Foundation Requirements Based on SCE 7-0 (60mph With Exposure B) Expected Net Sag 2'-2" xial,425 lb Shear,000 lb Torsion 900 lb-ft Momement 34,500 lb-ft

21 S:\danny\McKee\riton Gym\riton Gym Structural dwg - Monday, September 8, 207 3:35:34 PM F. H C C. D. E B C D E F H SHEET TITLE : MCKEE JOB # : 7-57 DRWN BY : JDD/TNS DTE: REVISED DTE: REVISED DTE: REVISED DTE: SHEET NO. : S. T S RE T E GI ST O ERE F L RCH B M WLTER T. McKEE, JR. No. 082 MONTGOMERY, L. D TEC I T NEW GYMNSIUM at RITON SCHOOL for the DLE COUNTY BORD of EDUCTION Ozark, labama M c K E E a n d S S O C I T E S R C H I T E C T U R E a n d I N T E R I O R D E S I G N 63 SOUTH HULL STREET MONTGOMERY, LBM 3604 (334)

22 S:\danny\McKee\riton Gym\riton Gym Structural dwg - Monday, September 8, 207 3:35:37 PM SHEET TITLE : MCKEE JOB # : 7-57 DRWN BY : JDD/TNS DTE: REVISED DTE: REVISED DTE: REVISED DTE: SHEET NO. : S.3 T S RE T E GI ST O ERE F L RCH B M WLTER T. McKEE, JR. No. 082 MONTGOMERY, L. D TEC I T NEW GYMNSIUM at RITON SCHOOL for the DLE COUNTY BORD of EDUCTION Ozark, labama M c K E E a n d S S O C I T E S R C H I T E C T U R E a n d I N T E R I O R D E S I G N 63 SOUTH HULL STREET MONTGOMERY, LBM 3604 (334)

23 S:\danny\McKee\riton Gym\riton Gym Structural dwg - Monday, September 8, 207 3:35:40 PM SHEET TITLE : MCKEE JOB # : 7-57 DRWN BY : JDD/TNS DTE: REVISED DTE: REVISED DTE: REVISED DTE: SHEET NO. : S3.2 T S RE T E GI ST O ERE F L RCH B M WLTER T. McKEE, JR. No. 082 MONTGOMERY, L. D TEC I T NEW GYMNSIUM at RITON SCHOOL for the DLE COUNTY BORD of EDUCTION Ozark, labama M c K E E a n d S S O C I T E S R C H I T E C T U R E a n d I N T E R I O R D E S I G N 63 SOUTH HULL STREET MONTGOMERY, LBM 3604 (334)

24 43'-6" 3'-4" 4'-8" 3'-4" 43'-5" DS/SB DS/SB 6.2 2'-" '-7" 4'-2" DS/SB DS/SB HC 6'-4" GB 8. LUNDRY 0 FEMLE VRSITY LOCKER ROOM 3 5'-8" 3'-0" GB2 TTD 3'-4" TOILET 3'-4" 3a 23'-9" 4 lockers 23'-8" 23'-8" 4 lockers 24'-5" GB3 7'-4" ENLRGED FLOOR PLN SCLE: /4" = '-0" GB GB 4 lockers HC HC 4 lockers SD MIR 8" 3'-0" 8" 3'-0" SRC GB3 2'-0" 3'-4" '-4" 8" 8" 3'-4" '-4" CORRIDOR 2 7'-8" 0'-0" 5'-4" 3'-4" 4'-8" 0 5'-4" 3'-4" 8. OFFICE B 3'-4" 8" B 5'-4" 3 4 EWC 2'-8" 5'-4" WHR 4'-8" B 6.2 7'-9" 6'-0" HGR FEMLE J.V. LOCKER ROOM 4 7'-4" " " 8'-8" 9'-4" MIR SD 6'-8" 8" 6'-8" TOILET 4a GB2 TTD PLTFORM 06a TOILET 9a GB2 TTD MIR SD RMP DOWN " PER. FT. MLE J.V. LOCKER ROOM 9 '-4" 3'-4" 8" 8" '-4" 3'-4" 2'-0" 5'-4" LNDING RMP DOWN " PER. FT. CORRIDOR 7 GB3 MLE VRSITY LOCKER ROOM SD MIR 8a 3'-0" 8" 3'-0" 8" 3'-9" 3'-4" '-4" 5'-4" 0'-0" 29'-4" 0'-0" 5'-4" '-4" 3'-4" 3'-9" 4'-8" '-4" WHR HGR 0'-0" 8'-8" HGR 4'-8" WHR 9 2'-8" 3'-4" EWC 8 5'-4" 7'-8" 6'-0" 3'-4" '-4" 3'-4" '-4" 6 SRC GB3 TOILET GB2 TTD 5'-4" 0'-0" 7'-8" B B '-4" 3'-4" 6'-4" 8. OFFICE 6 5'-4" 3'-4" 8" 3'-4" 3'-8" 2'-" GB HC NEW GYMNSIUM at RITON SCHOOL for the DLE COUNTY BORD of EDUCTION Ozark, labama M c K E E a n d S S O C I T E S R C H I T E C T U R E a n d I N T E R I O R D E S I G N 63 SOUTH HULL STREET MONTGOMERY, LBM 3604 (334) F O L T E B M T S T WLTER T. McKEE, JR. No. 082 MONTGOMERY, L. " 5'-8" 5 HC LUNDRY 5 2'-" '-7" 4'-2" 6.3 TEC RE I RCH D ERE GI ST - Z:\207\7-57 New Gymnasium for riton School, Dale County BOE\CD Drawings\rchitectural\.3 Floor Plans.dwg - Friday, September 22, 207 3:08:9 PM TOILET CCESSORIES LEGEND KEYNOTE TTD PTD SD GB GB2 GB3 MIR MIRL HC SRC EHD DESCRIPTION TOILET TISSUE DISPENSER TO BE MOUNTED 8" IN FRONT OF TOILET ND OUTLET OF DISPENSER MUST BE BETWEEN 5" & 48" FF (SEE SPECS) PPER TOWEL DISPENSER TO BE MOUNTED 48" OC FF (SEE SPECS) SOP DISPENSER TO BE MOUNTED WHERE HND CONTROLS RE 48" OC FF (SEE SPECS) 36" GRB BR MOUNTED WHERE CENTERLINE OF WLL MOUNT IS 6" OUT FROM CORNER OF WLL / TOILET PRTITION ND IS TO BE 33"-36" FF ( SEE SPECS) 42" GRB BR MOUNTED WHERE CENTERLINE OF WLL MOUNT IS 2" OUT FROM CORNER OF WLL / TOILET PRTITION ND IS TO BE 33"-36" FF (SEE SPECS) CORNER GRB BR ND IS TO BE 33"-36" FF (SEE SPECS) 8" X 36" MIRROR WITH SHELF TO BE MOUNTED WITH THE BOTTOM EDGE 35" FF ND THE TOP EDGE 7" FF (SEE SPECS) 8" x 48" MIRROR TO BE MOUNTED WITH THE BOTTOM EDGE 8" FF (SEE SPECS) HNDICPPED CCESSIBLE TOILET / URINL TO BE MOUNTED 7" FF 36" LONG SHOWER ROD ND CURTIN TO BE MOUNTED 84" FF ELECTRIC HND DRYER TO BE MOUNTED 40" FF (SEE SPECS) SYMBOL CORRIDOR --- EWC FEC WHR HGR GR DS/SB FLOOR PLN LEGEND DESCRIPTION SCHEDULED ROOM NME ND NUMBER ELECTRIC WTER COOLER (SEE DETIL xxx) FIRE EXTINGUISHER CBINET (SEE DETIL xxx) WLL MOUNTED METL HNDRIL - PINT METL HNDRIL / GURDRIL - PINT METL GURDRIL - PINT PREFINISHED METL DOWNSPOUT TO SPLSHBLOCK SHEET TITLE : MCKEE JOB # : DRWN BY : DTE: REVISED DTE: REVISED DTE: REVISED DTE: SHEET NO. : ENLRGED FLOOR PLNS 7-57 RBD / WW