St. Monica Food Pantry

Transcription

1 St. Monica Food Pantry HVAC WORK DIVISION 23 SECTION HVAC AIR DUCT ACCESSORIES PART 1. GENERAL 1.1 WORK INCLUDES A. Gravity Operated Backdraft Dampers B. Volume dampers C. Motor operated dampers D. Airflow Monitoring Stations E. Turning vanes 1.2 RELATED DOCUMENTS A. National Fire Protection Association, NFPA: 1) NFPA 90A: Air Conditioning and Ventilating Systems. 2) NFPA 90B: Standard for Installation of Warm Air Heating and Air Conditioning Systems. B. Underwriter's Laboratories, UL: 1) UL 181: Factory-Made Duct Materials and Air Duct Connections. (a) American Conference of Governmental Industrial Hygienists: Industrial Ventilation. (b) American Society of Heating, Refrigerating and Air Conditioning Engineers, ASHRAE: (c) Sheet Metal and Air Conditioning Contractors National Association, Inc., SMACNA: (d) SMACNA: HVAC Duct Construction Standards; First Edition SUBMITTALS A. Submit shop drawings for all materials in accordance with Division 01, Section B. Product Data: 1) Submit manufacturer's catalog cuts, specifications, installation instructions, and dimensioned drawings for each type of manufactured ductwork accessories. 2) Include pressure drop curve or chart for each type, and size of motorized control damper. 3) Submit schedule showing manufacturer's figure number, size, location, rated capacities, and features for each fire damper, and control damper. 4) Submit fire protection rating, maximum velocity/pressure ratings and manufacturer's installation instructions for each fire damper. Velocity/pressure ratings shall include both ducted and non-ducted data. 5) Submit manufacturers certified test data on dynamic insertion loss, self-noise power levels and aerodynamic performance for reverse and forward flow test for each duct silencer. C. Airflow Monitoring and Control 1) Submit product data sheets for airflow measuring devices indicating minimum placement requirements, sensor density, sensor distribution, and installed accuracy to the host control system. (a) Devices whose accuracy is the combined accuracy of the transmitter and sensor probes must demonstrate that the total accuracy meets the performance requirements of this specification throughout the measurement range.

2 St. Monica Food Pantry (b) Submit a schedule of airflow measuring devices indicating compliance with specified accuracy at minimum and maximum airflow rates. (c) Submit installation, operation and maintenance documentation. D. Shop Drawings: 1) Submit ¼ scale fabrication drawings showing all necessary fittings, dampers and access doors. 2) Coordinate fabrication drawings with field conditions prior to submittal. Changes in layout and design required to accommodate actual field conditions shall be specifically noted on drawings. E. LEED Submittals: 1) Product Data for Prerequisite EQ 1: Documentation indicating that units comply with ASHRAE , Section 5 - "Systems and Equipment." PART 2. EQUIPMENT 2.1 GRAVITY OPERATED BACKDRAFT DAMPERS A. Unless noted otherwise furnish and install gravity operated backdraft dampers for all roof mounted exhaust fans and where indicated on drawings. Damper frames shall be minimum 0.090" wall thickness, 6063T5 extruded aluminum with mitered corners. B. Blades shall be minimum 0.050" wall thickness, 6063T5 extruded aluminum with extruded vinyl edge seals. Blades shall be fitted with synthetic bearings. Damper linkage shall be concealed within the frame construction. C. The damper assembly shall be suitable for operation from -40 F to 200 F, and air velocities of 2500 FPM. Maximum backdraft airflow shall not exceed 12 CFM per square foot of damper at 0.5" w.g. static pressure differential. D. Backdraft dampers shall be mounted inside the roof curb for roof mounted exhaust fans (except laboratory process exhaust fans). The maximum force required to fully open the backdraft damper shall not exceed 0.15" w.g. static pressure differential. E. Manufacturers: 1) Ruskin Mfg. Co.: BD2/A2 Series 2) Air Balance, Inc. 3) Carnes 4) Perfco 5) Advanced Air 6) Greenheck 2.2 RECTANGULAR VOLUME DAMPERS A. Where shown on plans, and where required to properly balance the airflow in the HVAC supply, return, and exhaust ductwork systems provide rectangular, manual balancing type, volume control dampers. B. Frames shall be minimum 16 gage galvanized steel channel construction with corner braces. Frame sizes shall be available from 6" x 5" to 48" x 48". Fabricate single blade volume dampers for duct sizes to 9-1/2" x 30". Axles shall be 1/2" hex with molded synthetic bearings. Control shaft shall be 3/8" square plated steel construction.

3 St. Monica Food Pantry C. Damper blades shall be maximum 8" wide with opposed blade operation, and 16 gage galvanized steel construction. Damper blades shall be center and edge crimped and positively locked to hex axles. Provide factory mounted locking hand quadrants. D. Manufacturers: 1) Ruskin Mfg. Co.: MD35 Series 2) Air Balance, Inc. 3) Dowco Corp. 4) Nailor Industries 5) Greenheck 2.3 ROUND VOLUME DAMPERS A. Where shown on plans, and where required to properly balance the airflow in the HVAC supply, return, and exhaust ductwork systems provide round, manual balancing-type, volume control dampers. B. Frame and blade shall be minimum 20 gage galvanized steel construction. Frame sizes shall be available from 4" to 20" diameter. Control shaft shall be 3/8" square axle shaft extending beyond frame through factory mounted, locking hand quadrant. C. Bearing construction shall be molded synthetic. Finish shall be mill galvanized. Damper assembly shall be suitable for 1500 fpm velocity, and 250 F operating temperature. D. Manufacturers: 1) Ruskin Mfg. Co.: MDRS25 Series 2) Air Balance, Inc. 3) Dowco Corp. 4) Nailor Industries 5) Greenheck 2.4 VOLUME DAMPERS A. Where shown on plans, and where required to properly balance the airflow in the HVAC supply, return, and exhaust ductwork systems provide rectangular, manual balancing type, volume control dampers. Provide with cable control above inaccessible ceiling systems and manual quadrant where accessible. B. Furnish and install, at locations shown on plans, in accordance with schedules and as needed to balance airflow in HVAC systems. Provide commercial grade control dampers and remote cable control system that meet the following minimum standards. Dampers mounted in inlet of diffuser are not acceptable. Ceiling access panels are not acceptable. C. Dampers shall be round butterfly design or rectangular opposed blade design for low pressure drop. Round damper shall be heavy duty spiral shell with a 20 ga. V style blade, CRS steel shaft and oil impregnated bronze bearings requiring no lubrication. D. Rectangular dampers shall be opposed blade style for even distribution of air over face of grille. Damper shall be constructed of.050 extruded aluminum double channel frame and stainless steel hardware including the damper slide. Blades shall be.050 extruded aluminum with longitudinal reinforcing beads. Blades shall be installed in individual Teflon blade bushings in the damper frame. Manufacturer shall supply all necessary hardware for simple installation of remote cable controls system including the Bowden aluminum angle bracket and the Bowden control hub to accommodate the cable control system mounted on the damper. E. Cable control system shall consist of Bowden cable.054 stainless steel control wire encapsulated in 1/16 flexible galvanized spiral wire sheath to insure positive operation for up to 50 (less if there are multiple turns or bends). Control kit shall be designed for use with internally

4 St. Monica Food Pantry or externally controlled round or rectangular dampers and shall consist of 14 ga. Steel rack and pinion gear drive to convert rotary motion to push-pull motion. Control shaft shall be D-style flattened _ diameter with 265 degree rotation providing graduations for positive locking control. Control mounting through ceiling via 1 or 3 inconspicuous access port. F. Manufacturers: 1) Young Regulator 2.5 MOTOR-OPERATED DAMPERS (RECTANGULAR) A. Where shown on plans provide rectangular, motor operated, low leakage, opposed blade type, control dampers of the sizes indicated. B. Low leakage dampers shall have published leakage data certified under ACMA certified ratings program showing leakage through a 48"x 48" damper at 4" w.g. pressure difference to be not less than 6.2 cfm/sq.ft. C. Damper frames shall be constructed from 5" x 1" x.125" 6063T5 extruded aluminum hat channel with hat mounting flanges on both sides of frame. Each corner shall be reinforced with two die formed internal braces and machine staked for maximum rigidity. D. Damper blades shall be airfoil type extruded aluminum (maximum 6" depth) with integral structural reinforcing tube running full length of each blade. Blade edge seals shall be extruded vinyl double edge design with inflatable pocket which shall enable air pressure from either direction to assist in blade to blade seal off. Blades seals shall be locked in extruded blade slots without the use of cement, yet shall be easily replaceable in the field. E. Bearings shall be non-corrosive two piece molded synthetic. Axles shall be square or hexagonal (round not acceptable) to provide positive locking connections to blades and linkage. F. Manufacturers: 1) Ruskin Mfg. Co.: Series CD-60 2) Arrow United Industries 3) Penn Ventilator Co., Inc. 4) Nailor Industries 5) Greenheck 2.6 MOTOR-OPERATED DAMPERS (ROUND) A. Where shown on plans provide round, motor operated, low leakage, control dampers of the sizes indicated. B. Low leakage dampers shall have published leakage data certified under ACMA. Leakage through the damper in the closed position shall not exceed.15 scfm per inch of blade circumference at a pressure differential of 4" w.g. Leakage through bearings shall be not less than 1/4 cfm at 4" static pressure w.g. C. Damper frames shall be minimum 20 gage galvanized steel construction. Dampers greater than 20" diameter shall be fabricated with 1-1/2" x 1-1/2" reinforcement ring. D. Damper blade construction shall consist of two layers of galvanized steel with equivalent thickness of 14 gage. The blade shall include a firm, closed cell neoprene seal sandwiched between the two damper blades. E. Provide 1/2" diameter axle with stainless steel bearings pressed into the frame. Axles shall extend 6" beyond frame to function as the control shaft. All parts that are not protected shall be furnished with one coat of aluminum paint. F. Manufacturers: 1) Ruskin Mfg. Co.: CDRS25

5 St. Monica Food Pantry ) Arrow United Industries 3) Air Balance, Inc. 4) Nailor Industries 5) Greenheck 2.7 AIRFLOW MONITORING PRODUCTS INCLUDED IN THIS SECTION A. Duct and plenum mounted airflow measurement devices B. Fan inlet mounted airflow measurement devices C. Acceptable Manufacturers 1) Subject to compliance with requirements of this Section, provide products that comply with this specification by one of the following vendors: (a) EBTRON, Inc. Model GTx116-P and GTx116-F (basis of design) (b) Air Monitor D. Airflow/Temperature Measurement: 1) Provide airflow/temperature measurement devices (ATMD) where indicated on the plans. (a) Fan inlet measurement devices shall not be substituted for duct or plenum measurement devices indicated on the plans. E. Each ATMD shall consist of one or more sensor probes and a single, remotely mounted, microprocessor-based transmitter capable of independently processing up to 16 independently wired sensor assemblies. 1) Each sensor assembly shall contain two individually wired, hermetically sealed bead-in-glass thermistors. 2) Thermistors shall be mounted in the sensor assembly using a marine-grade, waterproof epoxy. Thermistor leads shall be protected and not exposed to the environment. 3) The airflow rate of each sensor assembly shall be equally weighted and averaged by the transmitter prior to output. 4) The temperature of each sensor assembly shall be velocity weighted and averaged by the transmitter prior to output. 5) Each transmitter shall have a 16-character alpha-numeric display capable of displaying airflow, temperature, system status, configuration settings and diagnostics. 6) Devices using chip-in-glass or diode-case chip thermistors are not acceptable. 7) Devices using less than two thermistors in each sensor assembly are not acceptable. 8) Devices using platinum wire RTDs are not acceptable. 9) Devices having electronic circuitry mounted in or at the sensor probe are not acceptable. 10) Pitot tubes and arrays are not acceptable. 11) Vortex shedding devices are not acceptable. F. All Sensor Probes 1) Each sensor assembly shall independently determine the airflow rate and temperature at each measurement point. 2) Each sensor assembly shall be calibrated at a minimum of 16 airflow rates and 3 temperatures to standards that are traceable to the National Institute of Standards and Technology (NIST). 3) Airflow accuracy shall be +/-2% of Reading over the entire operating airflow range.

6 St. Monica Food Pantry ) Devices whose accuracy is the combined accuracy of the transmitter and sensor probes must demonstrate that the total accuracy meets the performance requirements of this specification throughout the measurement range. 5) Temperature accuracy shall be +/-0.15 F over the entire operating temperature range of -20 F to 160 F. 6) The operating humidity range for each sensor probe shall be 0-99% RH (non-condensing). 7) Each sensor probe shall have an integral, U.L. listed, plenum rated cable and terminal plug for connection to the remotely mounted transmitter. All terminal plug interconnecting pins shall be gold plated. 8) Each sensor assembly shall not require matching to the transmitter in the field. 9) A single manufacturer shall provide both the airflow/temperature measuring probe(s) and transmitter for each measurement location. G. Duct and Plenum Probes 1) Probes shall be constructed of extruded, gold anodized, 6063 aluminum tube. All wires within the aluminum tube shall be Kynar coated. 2) Probe assembly mounting brackets shall be constructed of 304 stainless steel. Probe assemblies shall be mounted using one of the following options: (a) Insertion mounted through the side or top of the duct (b) Internally mounted inside the duct or plenum (c) Standoff mounted inside the plenum 3) The number of sensor housings provided for each location shall be as follows: Duct or Plenum Area (sq.ft.) Total # Sensors / Location <2 4 2 to < to < to <16 12 >= ) The operating airflow range shall be 0 to 5,000 FPM unless otherwise indicated on the plans. H. Fan Inlet Probes 1) Sensor assemblies shall be mounted on 304 stainless steel housings. 2) Mounting rods shall be field adjustable to fit the fan inlet and constructed of nickel plated steel. 3) Mounting feet shall be constructed of 304 stainless steel. 4) The operating airflow range shall be 0 to 10,000 FPM unless otherwise indicated on the plans. I. Transmitters 1) The transmitter shall have an integral LCD display capable of simultaneously displaying airflow and temperature. The LCD display shall be capable of displaying individual airflow and temperature readings of each independent sensor assembly. 2) The transmitter shall be capable of field configuration and diagnostics using an on-board pushbutton interface and LCD display. 3) The transmitter shall have a power switch and operate on 24 VAC (isolation not required).

7 St. Monica Food Pantry (a) The transmitter shall use a switching power supply fused and protected from transients and power surges. (b) The transmitter shall use watch-dog circuitry to assure reset after power disruption, transients and brown-outs. 4) All interconnecting pins, headers and connections on the main circuit board, option cards and cable receptacles shall be gold plated. 5) The operating temperature range for the transmitter shall be -20 F to 120 F. The transmitter shall be installed at a location that is protected from weather and water. 6) The transmitter shall be capable of communicating with other devices using one of the following interface options: (a) Linear analog output signals for airflow and temperature: Field selectable, fuse protected and isolated, 0-10VDC/4-20mA (4-wire) (b) RS-485: Field selectable BACnet-ARCNET, BACnet-MS/TP, Modbus-RTU or Johnson Controls N2-Bus (c) BACnet devices shall provide analog variables for airflow and temperature containing individual sensor airflow rate and temperature data. (d) 10 Base-T Ethernet: Field selectable BACnet Ethernet, BACnet-IP, Modbus-TCP and TCP/IP (e) Provide dynamic link libraries and VBA functions to interface Ethernet devices to Microsoft Excel for remote monitoring of airflow and temperature using a Windows 2000 or Windows XP based PC. (f) LonWorks Free Topology 7) The transmitter shall be capable of accepting an infra-red interface card for downloading airflow and temperature data or uploading transmitter configuration data using a handheld PDA (Palm or Microsoft Windows Mobile operating systems). (a) Provide PDA upload/download software. (b) Download software shall be capable of displaying and saving individual sensor airflow rates, the average airflow rate, individual sensor temperatures and the average temperature received from the transmitter. (c) Upload software shall be capable of displaying and saving all setup parameters that can be configured using the on-board pushbutton interface and LCD display. (d) Provide a Microsoft Excel file capable of creating balance reports from PDA data files transferred to a Windows 98 or higher based PC. (e) Provide a Microsoft Excel file to create configuration data files that can be transferred from a Windows 2000, Windows XP or higher based PC to a PDA for upload to one or more transmitters. J. The ATMD shall be UL listed as an entire assembly. K. The ATMD shall carry the CE Mark for European Union shipments. L. The manufacturer s authorized representative shall review and approve placement and operating airflow rates for each measurement location indicated on the plans. 1) A written report shall be submitted to the consulting mechanical engineer if any measurement locations do not meet the manufacturer s placement requirements. 2.8 TURNING VANES A. Constructed of same material as ducts where they are installed, but minimum 22-gauge, nonadjustable 90 degree turns. Turning vanes shall be single thickness, formed blade shape. Turning vanes shall be positioned and held in place with pre-formed guide rails. B. Manufacturers:

8 St. Monica Food Pantry ) Barber-Colman 2) Carnes Co. 3) Tuttle and Bailey PART 3. EXECUTION 3.1 INSPECTION A. Visit job site prior to fabrication and installation to verify all requirements, connections and conditions. Provide instructions to all parties with regard to shop drawing information and requirements. B. Starting work indicates acceptance of other in-place work. C. Before installation inspect building dimensions and service rough-in, including means of access for conditions affecting shop fabrication, equipment delivery and the installation of all ductwork and accessories. D. Provide inserts and anchors into other work for the support of this work. 1) Ensure these items are installed in the proper locations. 2) Include fastening devices to attach work. 3) Use the proper fasteners and anchors for the materials encountered and the operation and service of the equipment. E. Install ductwork and all accessories in accordance with the manufacturer's instructions using workers skilled and familiar with the items and the installation specifications. F. Shop assemble and test work prior to delivery to job site wherever possible. Sequence the installation and erection of work to ensure mechanical and electrical connections are affected in an orderly and expeditious manner. G. Coordinate all cutting, fitting and patching with the other trades involved to ensure a complete and finished installation. 3.2 METHOD OF INSTALLATION A. Comply with all of the manufacturer's best installation recommendations and instructions for all ductwork and accessories. B. Furnish and install roof curbs for all roof mounted ductwork and accessories. Curbs shall be as specified in Section HVAC Supports & Anchors of these specifications and the height shall be as indicated on drawings, but shall be not less than 13½" from base to top of nailer strip. C. Securely anchor roof curb to roof structure. Securely anchor ductwork and accessories to roof curb. Coordinate flashing and counterflashing with roofing installer for a watertight installation. D. Items with hinged bases shall be furnished with padlock hasps for padlocking. The anchoring of the hasp components shall be such that they cannot be removed when in the locked position. E. Furnish and install all steel members and accessories necessary to provide a complete and finished installation. F. Ducts shall be constructed, sealed and made airtight for pressures indicated on drawings. If pressure class is not indicated on the drawings, the ducts shall be sealed to 2" w.g. pressure class. All ducts shall be sealed in accordance with SMACNA Seal Class A. Fabricate and seal ductwork to maintain a maximum air leakage, inward or outward as follows: 1) Each 50 feet main or branch duct: 1%. 2) Total leakage any complete system: 5% of total air handled.

9 St. Monica Food Pantry G. Provide openings in ductwork to accommodate thermometers and controllers. Provide pitot tube openings for testing of systems, complete with metal can with spring device or screw to ensure against air leakage. Where openings provided in insulated or lined ductwork, install insulation material inside metal ring. H. Locate ducts with sufficient space around equipment to allow normal operating and maintenance activities to the greatest extent possible. I. Furnish and install all manually operated volume dampers, and devices where indicated on drawings and as required to insure proper balancing and control of air systems. Volume controllers shall be equipped with proper type operators for adjustment with final balance position clearly marked. J. The interior of all ducts and boots that can be seen through grilles, registers and diffusers shall be coated with flat black paint, except where duct is lined with black coated insulation. K. Where exposed ductwork passes through non fire-rated walls the space between the duct and the opening shall be closed with a compacted fill of 3/4 lb. density fiberglass. Provide and install sheet metal collar of not less than 20-gauge paint-grip type galvanized sheet steel on all side of the ductwork. Overlap the opening and ductwork by 1½" on all sides. Seal collars around ductwork and opening with silicone elastomeric sealant. L. The space between fire damper sleeve and the building construction shall be tightly sealed off with galvanized steel angle frame (not less than 10 ga.) on each side of opening. Securely attached angles to fire damper sleeve and to building construction to comply with UL and NFPA requirements for fire damper installation. M. Where dampers are installed in ductwork, and are not located behind a removable air grille or register, the Contractor shall provide an airtight access door in rectangular ducts and an airtight access panel in round ducts. These are required for access to the damper, fusible link and for inspection. Provide and install the access doors and panels regardless of whether they are indicated on drawings or not. N. Each fire damper shipment shall include the manufacturer's UL installation instructions. All fire dampers shall be installed in strict accordance with the manufacturer's UL installation instructions. O. Control Components: Install all control components in sheet metal equipment or ductwork as shown and/or indicated, including all automatic and manual control dampers, all flow measuring stations, all fire dampers, and all smoke dampers. Also any temperature sensors or indicators, humidity sensors or indicators, flow sensors, switches, or indicators, freeze stats, static pressure sensors, and end position switches that are not DDC controls. P. Routing: Locate ductwork runs, except as otherwise indicated, vertically and horizontally and avoid diagonal runs wherever possible. Locate runs as indicated by diagrams, details and notations or, if not otherwise indicated, run ductwork in shortest route which does not obstruct usable space or block access for servicing building and its equipment. Locate insulated ductwork for 1" clearance outside of insulation. Wherever possible in finished and occupied spaces, conceal ductwork from view, by locating in mechanical shafts, hollow wall construction or above suspended ceilings. Do not encase horizontal runs in solid partitions, except as specifically shown. Coordinate layout with suspended ceiling and lighting layouts and similar finished work. Coordinate with insulator to prevent installation of duct in such a way, that insulator cannot apply insulation. Q. Penetrations: Where ducts pass through interior partitions and exterior walls, seal space between construction opening and duct or duct insulation with sealant and sheet metal flanges of two gauges heavier than duct. Overlap opening on 4 sides by at least 1-1/2". Fasten to duct and substrate. Where ducts pass through fire rated floors, walls, or partitions, provide fire dampers, or fire/smoke dampers if indicated and provide firestopping between duct and substrate, as specified in Section R. Rectangular tees, bends and elbows shall be provided with turning vanes. In addition, provide manually operated volume dampers, as indicated and as needed, to ensure proper balancing and control of air systems.

10 St. Monica Food Pantry S. Installation: 1) Install backdraft dampers at inlet of exhaust fans or exhaust ducts as close as possible to exhaust fan unless otherwise indicated. 2) Install duct access doors on sides of ducts to allow for inspecting, adjusting, and maintaining accessories and equipment at the following locations: (a) At each change in direction and at maximum 50-foot spacing. (b) Upstream from turning vanes. 3.3 START-UP AND TESTING A. Leakage Tests: After each duct system or portion of a duct system is completed, this contractor shall test the section in accordance with the SMACNA HVAC Air Duct Leakage Test Manual. The tests shall verify that the entire duct system for each air handling unit has a total leakage rate of 1% or less of the total system design cfm. Leakage from non-duct components (fire dampers, smoke dampers, volume control boxes, etc.) are an integral part of overall system leakage, and these components shall be included in duct leakage tests. Contractor shall be responsible for any remedial efforts directed at products in order to bring the system or section into compliance with the leakage rate specified. B. Provide all blank off covers, fan connection points, and test holes required. Seal up of all test holes and removal of all covers after section of duct or entire duct system has been tested and approved as acceptable. C. By means of a suitable fan and test manometers, the systems shall be pumped up to approximately 3.5" w.g. of static pressure and held for a period of ten (10) minutes. After this period the pressure shall be reduced to 2" w.g. of static pressure and the duct systems shall be visually and audibly inspected to determine that all joints are tight. After all leaks are properly sealed, the duct shall be repressurized to 3.5" w.g. of static pressure and held for ten (10) minutes and then reduced again to 2" and all leaks rechecked. Contractor shall repair leaks and repeat tests until total leakage is less than 1% of total system design air flow. D. Contractor is responsible for the costs associated with any retests required due to total system duct leakage greater than the 1% of total cfm value. E. Contractor is responsible for submitting copies of certified calibration data for leakage test apparatus and the reports on the leakage tests. The report shall give an accurate description of the test procedure and results including any remedial action that was needed to obtain an acceptable test. Owner or Owner's Representative may be present for tests at Owner's discretion. 3.4 ADJUSTING AND CLEANING A. Remove protective ductwork caps or cover as it is being installed. B. Clean ductwork internally, unit by unit as it is installed, of dust and debris. Clean external surfaces of foreign substances which might cause corrosive deterioration of metal or, where ductwork is to be painted, might interfere with painting or cause paint deterioration. C. Temporary Closure: At ends of ducts which are not connected to equipment or air distribution devices at time of ductwork installation, provide temporary closure of polyethylene film or other covering which will prevent entrance of dust and debris until time connections are to be completed. D. Balancing: This contractor shall provide the initial balancing and adjusting of all air handling systems. All final testing and balancing will be by a testing and balancing contractor. This contractor shall assist during the final balancing and testing. Refer to Specification Section - "Testing, Adjusting, and Balancing" for air distribution balancing of metal ductwork. Seal any leaks in ductwork that become apparent in the balancing process.

11 St. Monica Food Pantry E. Clean, inspect and adjust dampers prior to system start-up to ensure equipment is operational and complete in all respects, including all accessories. Verify that all dampers are in the proper position before starting equipment. END OF SECTION