Glass beads surface dressing test section
|
|
- Albert Wade
- 5 years ago
- Views:
Transcription
1 Glass beads surface dressing test section O. Franchomme (COLAS SA) 1/ 24
2 Objective : Build a test section With an idealized texture Based on spherical patterns 2/ 24
3 Design elements Beads nature should not interfere with the texture profile measurements, The surface dressing must be applied on a perfectly smooth surface, The beads must stick to the asphalt support, The surface dressing must resist while the test vehicle pass by several times at 90 km/h 3/ 24
4 Choice of the beads Nature : glass beads Surface : Frosted the profile measurement is not affected by reflections ensure a better sticking Diameter : 5 mm ± 0.3 mm. 4/ 24
5 Construction technique Support : Asphalt layer Average texture depth : 1mm Glass beads Stick «Voidfilling» Asphalt layer 5/ 24
6 Laboratory Tests 6/ 24
7 Solution 1 A classical surface dressing Void filling : Bituminous mixture Binder : Bitumen emulsion Bitumen emulsion «Voidfilling» bituminous mixture Asphalt layer Glass beads 7/ 24
8 Laboratory tests - Adhesion test according to NF EN standard - Laboratory surface dressing application 8/ 24
9 Adhesion tests : Between glass beads and bitumen emulsion Test consists in estimating the behaviour of a binder film (in this case emulsion) on an aggregate (here glass beads). After 72 hours in water at 60 C Residual film must cover more than 75% of the aggregate surface. 9/ 24
10 Adhesion tests : Between glass beads and bitumen emulsion Results After conservation, whichever emulsion was tested, less than 50 % of the beads surface was covered by the binder film Poorly coated glass beads 10 / 24
11 Laboratory surface dressing application Tests were carried out with different bitumen emulsions and frosted glass beads The samples behaviour was regularly observed to estimate the breaking time for emulsion. 11 / 24
12 Laboratory surface dressing application Aspect of the Surface Dressing after 1h30 The emulsion did not break totally Aspect of the Surface Dressing after 24 h No adhesion of the beads to the support layer 12 / 24
13 Solution 1 Conclusions laboratory tests Solution 1 proved to be impossible For 2 reasons : The emulsion breaking time was too long ( > 2 h) The adhesion between glass beads and emulsion was not satisfactory. 13 / 24
14 Solution 2 A surface dressing with resin Void filling : methacrylic resin with filler Binder : Resin type Colgrip Resin COLGRIP «Voidfilling» methacrylic resin Asphalt layer Glass beads 14 / 24
15 Solution 2 A surface dressing with resin The sample is manufactured according to the method that will be applied on site: Application of the Serac resin with a smooth spatula One hour delay to allow for resin to harden. Application of the Colgrip SE resin with a 5 mm jagged scraper to obtain a 2.5 mm thick binder layer. This thickness allows sealing the beads on half their diameter. Glass beads are then spread in excess. After the Colgrip resin hardens, excess glass beads are removed by sweeping. 15 / 24
16 Solution 2 A surface dressing with resin The beads that were stuck this way cannot be removed from the support. Surface aspect the laboratory sample This technique is therefore validated 16 / 24
17 Glass beads test section 17 / 24
18 Glass beads test section Test section was built on September 16th, The weather was cloudy, with an outside temperature ranging from 10 to 17 C. 18 / 24
19 Phase 1: Application of Void filling Support preparation Sweaping Limitation of the area to be covered 19 / 24
20 Phase 1: Application of Void filling Support preparation SERAC is applied with a smooth spatula With SERAC Without SERAC Visual aspect after SERAC is applied 20 / 24
21 Phase 2: Application of the Colgrip SE Colgrip resin is applied with a 5 mm jagged scraper to obtain a 2.5 mm thick layer Glass beads are manually spread in excess 21 / 24
22 Phase 2: Application of the Colgrip SE Visual aspect of the test surface before excess glass beads are removed by sweeping 22 / 24
23 Phase 3: Surface sweeping to remove the excess glass beads Global view of the resin and glass beads test section 23 / 24
24 Thanks for your attention 24 / 24
The Shell Bitumen Handbook
The Shell Bitumen Handbook Sixth edition Principal aufhors Dr Robert N. Hunter, Andy Self and Professor John Read Shell Bitumen Contents About the principal authors Foreword Acknowledgements xii xiv xv
More informationSeal Coats and Surface Treatments Fred J. Benson, Dean of Engineering A. and M. College of Texas College Station, Texas The construction, as here
Seal Coats and Surface Treatments Fred J. Benson, Dean of Engineering A. and M. College of Texas College Station, Texas The construction, as here discussed, consists of an application of bituminous material
More informationA5EE-337 DURABILITY OF A BITUMEN IN A HOT MIX ASPHALT: CONSEQUENCES OF OVER-HEATING AT THE MIXING PLANT
A5EE-337 DURABILITY OF A BITUMEN IN A HOT MIX ASPHALT: CONSEQUENCES OF OVER-HEATING AT THE MIXING PLANT Carole Gueit, Michel Robert Colas Campus for Sciences and Techniques, Road Chemistry service, Magny-les-Hameaux,
More informationCOMPLETE SOLUTION TO SAFE HIGH QUALITY ROAD & LINE MARKINGS. Road & Line Marking. Paint Equipment Additives & Accessories
COMPLETE SOLUTION TO SAFE HIGH QUALITY ROAD & LINE MARKINGS Road & Line Marking Paint Equipment Additives & Accessories WELCOME Specialized Coating Systems is one of South Africa s leading paint manufacturing
More information4.1. Foremen 4.2. Concrete plant manager 4.3. Concrete plant operator 4.4. Personnel performing saw cutting and joint sealing
10-1. JOINTED PLAIN CONCRETE PAVEMENT GENERAL Summary This work includes constructing jointed plain concrete pavement. Comply with Section 40, "Concrete Pavement," of the Standard Specifications. Submittals
More informationMaximising Durability and Performance of Marking Systems. NZRF Conference Rotorua Aug
Maximising Durability and Performance of Marking Systems NZRF Conference Rotorua Aug 23-24 2011 Factors affecting performance AS4049.4 Pavement Texture Applications Conditions Application Equipment Application
More informationSTABILIZATION OF SANDY SOIL WITH USE OF BITUMEN EMULSION
STABILIZATION OF SANDY SOIL WITH USE OF BITUMEN EMULSION Prof. Rajesh Jain 1, Tarun Namdeo 2 1Associate Professor, Jabalpur Engineering College, Jabalpur 2ME Scholar, Jabalpur Engineering College, Jabalpur.
More informationAppendix D Answers To Chapter Review Questions
Appendix D Answers To Chapter Review Questions Chapter 1 Standard Practices 1. The purpose of pavement markings is to communicate information about the traveled roadway so motorists can safely reach their
More informationTECHNICAL DATA SHEET PlastiRoute RP-2C All Colours
Product Description Application Application Equipment is a paste-like, solvent-free road marking cold plastic which cures by addition of peroxide initiator. It is recommended as permanent marking for very
More informationHow to build a Javelin Skiff
How to build a Javelin Skiff This is not your grandfather s plywood boat! The Javelin involves a high-tech type construction, called composite. The hull can be constructed with foam or plywood; these materials
More informationADHEBIT Adhesion Promoters
ADHEBIT Adhesion Promoters A new generation of adhesion promoters that combines superior coating and exceptional workability with immediate commercial saving The life of an asphalt pavement depends basically
More information3D printing in MODERN MOLD MAKING. Cutting Time & Costs in Short Run Production.
3D printing in MODERN MOLD MAKING. Cutting Time & Costs in Short Run Production. RTV Molding Tutorial 2 INDEX 1. The Introduction 2. Raw Facts and Figures 3. FDM Patterns for Modern Mold Making Preliminary
More informationAgeing modelling of seal bitumen binder
1 1 1 1 1 1 1 1 0 1 0 1 Ageing modelling of seal bitumen binder Estimé Mambula wa Kanyinda Mukandila 1, Wynand Jacobus van der Merwe Steyn ( 1 ix engineers,eastwood Office Park, Protea House, 0 Lynwood
More informationInstallation Instructions Recommended Tools
Recommended Tools Tape Measure Sharp Knife Duct Tape Mineral Spirits Clean Cloth Isopropyl Alcohol Blunt Putty Knife Caulking Gun Caulking Trowel Material Sizing 1. Joints must be sized every 5-7 feet
More informationCrackle Paste is a water-based product formulated with styrene-acrylic copolymer emulsions, and may have a tendency to yellow.
PRODUCT DESCRIPTION Crackle Paste is a water-based product formulated with styrene-acrylic copolymer emulsions, and may have a tendency to yellow. This product has white, low-density solids that replace
More informationSURFACE PREPARATION AND MATERIAL APPLICATION KEIM MINERAL PAINTS
SURFACE PREPARATION AND MATERIAL APPLICATION KEIM MINERAL PAINTS PRE-TREATMENT KEIM Mineral Paints are different to conventional film forming paints. Mineral paints are made with potassium silicate and
More informationIMPROVEMENT OF SHEAR STRENGTH OF SOIL USING BITUMEN EMULSION
International Journal of Civil Engineering and Technology (IJCIET) Volume 7, Issue 6, November-December 216, pp. 156 165, Article ID: IJCIET_7_6_17 Available online at http://www.iaeme.com/ijciet/issues.asp?jtype=ijciet&vtype=7&itype=6
More informationRetroreflective Road Markings
Retroreflective Road Markings Road markings: safer mobility by day and night The secret of night time visibility of road markings: glass beads What happens at night Without beads, there is no retroreflection!
More informationTHE ROADMARKING EXPERTS
THE ROADMARKING EXPERTS With a long history of making and suppling high-quality road safety systems, Damar Industries is a recognised market leader in roadmarking products. Damar has an extremely comprehensive
More informationC. For cold-applied tape, the pavement temperature shall be at least 70 F.
SECTION 6100 - PAVEMENT MARKING (THERMOPLASTIC) PART 1 - GENERAL 1.01 SCOPE: This Section covers hot-applied, extruded thermoplastic and cold-applied tape for white and yellow pavement marking. Topics
More informationDAMPING MATERIALS BITUMEN FLEX PANEL BITUMEN SMOOTH PANEL
BITUMEN FLEX PANEL Self-adhesive high density bituminuous laminate. Composed of mixture with a basis of bitumen, plasticizers, elastomers, Index: 014-0435 SPECIFICATION 1,8-1,9 g/cm³ Sold per. Panel (50
More informationPart 1. Introduction
Part 1 Introduction Surface course, usually max 40mm thick Binder course, usually max 60mm thick Base, thickness designed and depends on anticipated traffic loadings, up to 300mm thick Terminology Sub-base,
More informationWorking Methods TOTAL JOINERY REPAIR SOLUTIONS
Working Methods TOTAL JOINERY REPAIR SOLUTIONS Preparation Remove paint at least 10mm from the area to be repaired. Remove all decayed and soft timber using a Repair Care Mini-PROFI router and round cutter.
More informationInnovative laboratory equipment. Preliminary testing to determine the mix quality.
Innovative laboratory equipment. Preliminary testing to determine the mix quality. 02 03 More control. Improved quality. THE LABORATORY FOAMED BITUMEN PLANT PERFORMS A SERIES OF PRECISE MEASUREMENTS TO
More informationGluing windows with SABA Glasstack 760
Info sheet 208 Gluing windows with SABA Glasstack 760 Version 2008-05-08 EN, replaces all prior versions Page 2 of 9 Info sheet 208 Gluing windows with SABA Glasstack 760, version 2008-05-08 EN 1. Introduction
More informationFibertex AM2 for Stress relieving
C O N S T R U C T I O N 210.02 Fibertex AM2 for Stress relieving C O N S T R Fibertex AM2 for Stress relieving To avoid reflective cracking of new asphalt To protect the subsoil from water intrusion and
More informationSPECIFICATION FOR WATERBORNE TRAFFIC LINE PAINT
Page 1 of 5 ATTACHMENT I Commonwealth of Pennsylvania Department of Transportation SPECIFICATION FOR WATERBORNE TRAFFIC LINE PAINT August 14, 2006 1. SCOPE 1.1 Scope. This specification covers fast-drying
More informationeco-shake INSTALLATION INSTRUCTION
1 eco-shake INSTALLATION INSTRUCTION NOTE: Shuffling the eco-shakes during installation may be necessary to obtain a uniform color throughout the roof. Due to the natural wood content in the ecoshakes,
More informationWorking Methods TOTAL JOINERY REPAIR SOLUTIONS
Working Methods TOTAL JOINERY REPAIR SOLUTIONS Preparation Remove paint at least 10mm from the area to be repaired. Remove all decayed and soft timber using a Repair Care Mini-PROFI router and round cutter.
More information3/16 OR 1/4 FRAMELESS SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS
/ OR / FRAMELESS SWING DOOR WITH SINGLE INLINE OR TWO INLINE S This instruction sheet applies to the following units with a magnetic handle. C7, C7, C79 This instruction sheet also applies to the following
More informationMETHOD STATEMENT. Sika FloorJoint S
METHOD STATEMENT Table of Contents 1 SCOPE 3 2 PRODUCT 3 2.1 3 3 SUBSTRATE REQUIREMENTS 3 4 Preparation of the Substrate 3 4.1 Mapping of the joint panels on the floor for the saw cuts 3 4.2 Execution
More informationCommonwealth of Pennsylvania PA Test Method No. 517 Department of Transportation October Pages LABORATORY TESTING SECTION. Method of Test for
Commonwealth of Pennsylvania PA Test Method No. 517 Department of Transportation 10 Pages 1. SCOPE LABORATORY TESTING SECTION Method of Test for DETERMINATION OF ACCELERATED POLISH OF COARSE AGGREGATE
More informationDesign and industrial application of a microsurfacing pavement based on non-venezuelan bitumen.
Design and industrial application of a microsurfacing pavement based on non-venezuelan bitumen. Claude Emmanuel Giorgi 1, a, Frédéric Loup 2, Delphine Simard 2, Jérémy Thomas 3 1 Technical Management,
More informationUnit PO0205K Knowledge of Applying Fillers and Foundation Materials
Assessment Requirements Unit PO0205K Knowledge of Applying Fillers and Foundation Materials Content: The types of substrates likely to be found in vehicle refinishing a. List types of substrate to include:
More informationSANS 3001-BSM3:201X Edition 1
ISBN 978-0-626-XXXXXX SANS 3001-BSM3:201X SOUTH AFRICAN NATIONAL STANDARD Civil engineering test methods Part BSM3: Vibratory hammer compaction of test specimens of bitumen stabilized material WARNING
More informationBuilding Instructions ARTEMIS Sailing Canoe Day Six Version 1.0 Brian Pearson & Dr. Axel Schmid Day Six. Align and Glue Planks
Version 1.0 Brian Pearson & Dr. Axel Schmid 2016 Align and Glue Planks Steps: Align boat, check dimensions Join planks provisionally Pull wires Glue the outside planks Tools and Materials: Epoxy putty
More informationPhotonic device package design, assembly and encapsulation.
Photonic device package design, assembly and encapsulation. Abstract. A.Bos, E. Boschman Advanced Packaging Center. Duiven, The Netherlands Photonic devices like Optical transceivers, Solar cells, LED
More information1. INTRODUCTION 2. REFERENCE SPECIFICATIONS. Page -1- Bonding and Grouting
Page -1-1. INTRODUCTION 1.1 Scope This specification covers non-shrink and epoxy grouting of structural column base plates and equipment bases, Portland cement grout for minor elements and bonding agents
More information380 Swimming Pool Paint
Issued 21 st April 2010 PRODUCT DATA SHEET UNPAINTED CEMENT 380 Swimming Pool Paint SURFACE PREPARATION New cement or render should be allowed to cure for at least 21-28 days before any preparation is
More informationTOOLKIT PART 4 MANUFACTURING PROCESSES
Understanding which manufacturing process has been used to make an object can help you identify its material as different materials are manufactured with different process. Different manufacturing processes
More informationRESULTS ACHIEVED BY TEAMWORK
RESULTS ACHIEVED BY TEAMWORK David Wallman Business Development Manager M: 0427 649 639 E: david@rnrbitumen.com.au Rock N Road Bitumen Pty Ltd provides a superior service for all bitumen design and sealing,
More informationEXTRA LIGHT. installation. maintenance. and MADE IN FLORIM
MADE IN FLORIM INSTALLATION AND MAINTENANCE 1) Characteristics of the surface choice of adhesive grout. 2) Laying the tiles 2 To ensure excellent adherence, the surface must always be uniform light colored,
More informationIn recent years, pressure has been placed on asphalt shingle manufacturers
A STRONGER B O N D High-wind-resistant shingles demand high-performance adhesives by Tom Nichols In recent years, pressure has been placed on asphalt shingle manufacturers to upgrade their products performance
More informationDAP Latex Window Glazing
DAP Latex Window Glazing PRODUCT DESCRIPTION DAP Latex Window Glazing is a ready-to-use glazing compound that may be used for face glazing single pane glass in wood or metal window frames. Its spout allows
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationShape Analysis of Bituminous Mixes With SBR
100 90.45 73.2 66.21 47.36 34.57 18.67 13.67 10 7.32 25 mm 19 mm. 12.5 mm. 10 mm. 4.75 mm. 2.36 mm. 0.6 mm. 0.3 mm. 0.15 mm. 0.075 mm International Journal of Engineering Research and Development e-issn
More informationCHAPTER 5 PREFORMED THERMOPLASTIC
OBJECTIVES CHAPTER 5 PREFORMED THERMOPLASTIC 1) Preformed Thermoplastic 2) Components 3) Material Characteristics 4) Application Methods 5) Application Considerations 6) Inspection And Quality Control
More informationUNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS
UNIT REF: PO0205K UNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS Level: 2 Route: Knowledge Credit Value: 6 GLH: 45 Mapping: This unit is mapped to the IMI NOS PO2 and PO5 Rationale:
More informationThe use of high frequency transducers, MHz, allowing the resolution to target a few cm thick in the first half meter suspect.
METHODOLOGY GPR (GROUND PROBING RADAR). In recent years the methodology GPR (Ground Probing Radar) has been applied with increasing success under the NDT thanks to the high speed and resolving power. As
More informationTechnical documentation. Sealoflex Color asphalt and Colorfalt V pigments
Technical documentation Sealoflex Color asphalt and Colorfalt V pigments This technical description intends to provide additional guidelines for the proper handling and installation of supplied products.
More informationTapecoat. Application Guideline
Tapecoat Application Guideline 1.0 SCOPE This document contains general instructions and recommended practices for the application of Tapecoat wax/petrolatum coating systems. The various coating grades
More information1982 Hydrostream Viking Restoration
1982 Hydrostream Viking Restoration Part 2a: The Rebuild Daniel W. Rickey Winnipeg, Manitoba Canada daniel@cancercare.mb.ca 2000-07-19 Introduction Part one of this report showed how the shoddy manufacturing
More informationAIR-RECTIFIED BITUMNEN
Bitumen Glossary A AIR BLOWING The process by which compressed air is blown into a feedstock, which may include VACUUM RESIDUE, PROPANE-PRECIPITATED ASPHALT mixed with ATMOSPHERIC RESIDUE, and/or a FLUX
More informationCrazy Stencil Tips & Tricks
Crazy Stencil Tips & Tricks [ adding tools to your art arsenal ] by Darlene Olivia McElroy darleneoliviamcelroy.com A quick little FREE step by step tutorial about unusual stenciling techniques. Expand
More informationLaboratory foamed bitumen plant WLB 10 S and twin-shaft compulsory mixer WLM 30. Preliminary testing to determine the mix quality.
Laboratory foamed bitumen plant WLB 10 S and twin-shaft compulsory mixer WLM 30 Preliminary testing to determine the mix quality. 02 03 Outstanding features of the WLB 10 S and WLM 30 3 BITUMEN INJECTION
More informationIntroduction. Unitized abrasive materials. Context
Unitized Introduction With its slogan Time saving abrasives Cibo is constantly striving to save our customers time and money. The range of unitized abrasive materials fits in perfectly with this strategy.
More informationElcometer Muller Laboratory Grinder
English Elcometer 2000 Muller Laboratory Grinder Operating Instructions English is a registered trademark of Elcometer Limited. All other trademarks acknowledged. Copyright Elcometer Limited. 2009. All
More informationMATERIAL AND EQUIPMENT STANDARD FOR COAL TAR MASTIC (COLD APPLIED) ORIGINAL EDITION AUG. 1993
MATERIAL AND EQUIPMENT STANDARD FOR COAL TAR MASTIC (COLD APPLIED) ORIGINAL EDITION AUG. 1993 This standard specification is reviewed and updated by the relevant technical committee on May 1999. The approved
More informationMid-shade iron oxide reds, equivalent to Bayferrox 130, are the most suitable pigments for colouring normal bitumen.
Coloured bitumen concrete or mastic asphalt are frequently used to create coloured surfaces for streets, squares, etc. In particular, red surfacing materials are used for cycle paths, pavements and parking
More informationThe City of Winnipeg SHINGLE ROOF REPLACEMENT Section Replacement of Shingle Roof - Louis Riel Library Page 1 of 5 Bid Opp. No.
Replacement of Shingle Roof - Louis Riel Library Page 1 of 5 PART 1 GENERAL 1.1 SCOPE OF WORK.1 Total roof area approximately 1,312 m 2. The Work includes, but is not limited to:.1 Removal and disposal
More informationBUREAU OF INDIAN STANDARDS. Draft Indian Standard HOT APPLIED THERMOPLASTIC ROAD MARKING MATERIAL
FOR BIS USE ONLY DOC:CHD 20 (1937)C December 2012 BUREAU OF INDIAN STANDARDS Draft Indian Standard HOT APPLIED THERMOPLASTIC ROAD MARKING MATERIAL (Not to be reproduced without the permission of BIS or
More informationPaper presented at the New Zealand Roading Symposium, August 1983, Wellington New Zealand
Paper presented at the New Zealand Roading Symposium, August 1983, Wellington New Zealand ROAD CHEMICALS, SELECTION, TEST METHODS AND FUTURE TRENDS W.T. Hulshof*, Development Manager Akzo Chemie bv Amersfoort
More informationEasy Jewelry Box. Easy Jewelry Box 1
This easy to build dresser style jewelry box is designed to use standard board sizes you may already have on hand. Drawers are lined in felt and have felt covered bottoms to glide smoothly on the shelves
More informationCatalog October Speedi-Sleeve The quickest and most economical way to repair worn shafts
Catalog 457027 October 2005 Speedi-Sleeve The quickest and most economical way to repair worn shafts Table of Contents The Speedi-Sleeve concept...3 SPEEDI-SLEEVE, the quickest and most sensible way to
More informationX-P High Performance Nail for Fastening to Concrete and Wood to Steel applications
X-P High Performance Nail for Fastening to Concrete and Wood to Steel applications Product data X-P_ MX Ø 8.2 2.4 X-P_ P8 Ø 8.2 2.4 Ø 4.0 L s L L s L Ø 4.0 Features and Benefits A specially hardened fastener
More informationSURFACE FINISH MAINTENANCE
SURFACE FINISH MAINTENANCE SURFACE FINISH MAINTENANCE Lumec strongly recommends that you maintain your luminaires twice a year in order to prolong the appearance of the finished surface. By following this
More informationAdhesion Agents for Use in Hot Mixes and Cut-Back Bitumens A.D. James, R. Senior, and D. Stewart, Akzo Chemie UK Ltd
Presented at the 3 rd IRF Middle East Regional Meeting, Riyadh, Saudi Arabia, 1988 Adhesion Agents for Use in Hot Mixes and Cut-Back Bitumens A.D. James, R. Senior, and D. Stewart, Akzo Chemie UK Ltd 1.
More informationLUXAPOOL EPOXY POOL COATING APPLICATION GUIDE. New Cement Pools
LUXAPOOL EPOXY POOL COATING APPLICATION GUIDE New Cement Pools 1. The render should consist of fresh cement and pure, clean sand only. Allow the render to cure for a minimum of 21 days prior to any preparation
More informationWOOD FINISH MAINTENANCE: notes and advices for the maintenance of Albertini windows and doors
WOOD FINISH MAINTENANCE: notes and advices for the maintenance of Albertini windows and doors Your Albertini windows and doors have been treated as follows: One flow coat application of preservative stain;
More informationPavement materials: Bitumen
Pavement materials: Bitumen Lecture Notes in Transportation Systems Engineering Prof. Tom V. Mathew Contents 1 Overview 1 1.1 Production of Bitumen............................... 2 1.2 Vacuum steam distillation
More informationTHE STANDARD IN MEASURING
WHITE PAPERS Understanding Gloss with the Rhopoint IQ-S The Rhopoint IQ-S is a specially designed instrument built specifically to match automotive interior gloss measurement standards. KONICA MINOLTA
More informationCOMPOSITES LAB MANUAL
COMPOSITES LAB MANUAL Version 1 Lab 4: Wet Layup of complex shapes The original version of this manual was a one student senior design project written by Katherine White, the Composite lab assistant, during
More informationArte PINTI. since 1946 PROFESSIONAL PAINT & TOOLS MADE IN ITALY
t Arte since 1946 PINTI PROFESSIONAL PAINT & TOOLS MADE IN ITALY N.1/2015 Index Roma Firenze Venezia Metallika Crystal Ferrum Star Milano Powder Resin Arte is the collection of decorative effects that
More information4 x 2.2 m SLEEPING BARREL. health, beauty, peace of mind SPECIFICATIONS WINDOWS ROOF SHINGLES TRANSPORTATION MAINTENANCE
4 x 2.2 m SLEEPING BARREL health, beauty, peace of mind SPECIFICATIONS WINDOWS ROOF SHINGLES TRANSPORTATION MAINTENANCE SPECIFICATIONS OF PRODUCT HERE'S WHAT YOU GET Wall and floor panels from spruce;
More informationStudent Sheet. P003S: Making Paint with Minerals
Student Sheet In this practical I will be: Creating egg tempera paints and oil paints from different types of minerals. Evaluating the different paints, looking at various aspects, including: o what colours
More information"Material fields per se" such as polymer materials or compositions and kind of fibrous web.
D06N WALL, FLOOR OR LIKE COVERING MATERIALS, e.g. LINOLEUM, OILCLOTH, ARTIFICIAL LEATHER, ROOFING FELT, CONSISTING OF A FIBROUS WEB COATED WITH A LAYER OF MACROMOLECULAR MATERIAL; FLEXIBLE SHEET MATERIAL
More informationHouse Wall Paint: two types of paints and a manufacturing process of latex paint
House Wall Paint: two types of paints and a manufacturing process of latex paint (image from www.bidsbypros.com) Table of Contents History and background knowledge of paint manufacturing... 2 Paint components...
More informationQUARTZ FABRICATION MANUAL
QUARTZ FABRICATION MANUAL Quartz Fabrication Manual Rev. 1 Page 1 of 26 TABLE OF CONTENTS Product Description. 3 Slab Inspection.. 4 Fabrication Equipment.. 6 FABRICATION TIPS Cutting The Slab. 7 General
More informationPolishing Concrete: Diamonds and Densifiers. What is polishing? Surface Profile and Sheen 11/4/2013
Polishing Concrete: Diamonds and Densifiers By Jeffrey Girard, P.E. The Concrete Countertop Institute Copyright 2013 What is polishing? The act of changing a concrete floor surface, with or without aggregate
More informationInfluence of the frontal joint of the bitumen sheet on the final strength of the joint
Influence of the frontal joint of the bitumen sheet on the final strength of the joint Jan Plachý 1,*, Jana Vysoká 1, and Radek Vejmelka 1 1 Vysoká škola technická a ekonomická v Českých Budějovicích,
More informationCONTROL AND RESEARCH LABORATORIES IN THE ASPHALT INDUSTRY
CONTROL AND RESEARCH LABORATORIES IN THE ASPHALT INDUSTRY (Is there any space for the emulsions?) WITH A SHORT INTRODUCTION ON THE ITALIAN MARKET Carlo Giavarini, SITEB Italy SHORT INTRODUCTION ON THE
More informationPCTC Guide Specification-PCTC01
PCTC Guide Specification-PCTC01 Guide for Preparation of Specifications for the Application of A Refined Coal Tar Emulsion Without Additives Over Asphaltic Pavements 1. GENERAL This guide can be used to
More informationScreen Making For Membrane Switches
Screen Making For Membrane Switches By Wolfgang Pfirrmann, KIWO Inc. Printing membrane switches requires skill and control over the process. This industry has set fairly tight quality standards in regard
More informationRHEOLOGICAL ANALYSIS OF CRUMB RUBBER MODIFIED BINDER
RHEOLOGICAL ANALYSIS OF CRUMB RUBBER MODIFIED BINDER G A J MTURI and J O CONNELL* CSIR Built Environment, Transport Infrastructure Engineering, Pretoria 0001, South Africa Tel: +27 12 841 2234; E-mail:
More informationAn Experimental Study on Effect of Scrap Tyre Crumbed Rubber on 80/100 Grade Bitumen
IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 9 February 21 ISSN (online): 2349-1 An Experimental Study on Effect of Scrap Tyre Crumbed Rubber on 8/1 Grade
More informationCharacterisation of Bituminous Mix Using River Bed Materials
ISSN (Online) : 975- Characterisation of Bituminous Mix Using River Bed Materials Manoj K. Sahis 1, Dipesh Majumdar, Partha P.Biswas 3, Sourav Halder, Agnimitra Sengupta 5 Department of Construction Engineering
More information380 Swimming Pool Paint
Issued 21 st June 2011 PRODUCT DATA SHEET 380 Swimming Pool Paint SURFACE PREPARATION If your pool has been previously painted but you are unsure as to whether or not it was with chlorinated rubber or
More informationSealing Elements. Technical Handbook O-rings. 15. Tolerances and Surface Imperfections
15. Tolerances and Surface Imperfections Size tolerances and surface imperfections on O-rings are influenced by the tolerance, finish, and cleanliness of the mold cavities from which they are produced.
More informationThe Portuguese Approach on Implementation of Harmonised European Asphalt Standards
A Southern European Approach The Portuguese Approach on Implementation of Harmonised European Asphalt Standards Dr. Maria C. M. Azevedo, CAeMD, Chairperson of Portuguese Technical Committees on Bituminous
More informationthe ultimate fanlights range traditionalfanlights fusion glass tile fanlights bevelled glass fanlights
the ultimate fanlights range traditionalfanlights fusion glass tile fanlights bevelled glass fanlights traditionalfanlights Adding the personal touch of a leaded, coloured glass effect to a fanlight is
More informationC Paint. Product Information Sheets
T A T G O E C Paint Product Information Sheets Cottage Paint- 8oz jar Available in many pre-tinted colors -see chart. Used for painting furniture and cabinetry. Water based Clay paint that is easily distressed
More informationRhinoArt Decor Polystyrene Mouldings
C Art 12/8/08 2:31 PM Page 2 RhinoArt Decor Polystyrene Mouldings CORNICES Made of high density POLYSTYRENE for a perfectly smooth surface. RhinoArt Decor adhesive covers 8-10 linear metres per kg. 62
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationSketchpaint. Ideal for turning any smooth surface into a whiteboard. Ready to use in 5 days
Sketchpaint Ideal for turning any smooth surface into a whiteboard SketchPaint - A whiteboard straight out of a tin! White Gloss or Transparent Finish Simple application Tin size available: 3m² or 6m²
More information- Flash. A very thin gage, sometimes film-like material, which extends from the parting line projection, shall be removed.
SEALING ELEMENTS 15. Tolerances and Surface Imperfections Size tolerances and surface imperfections on O-rings are influenced by the tolerance, finish, and cleanliness of the mold cavities from which they
More informationFinishing guide Textured black
Finishing guide Textured black The M4 Mk2 mini monitor kit featured in this guide is designed and manufactured in Australia by The Loudspeaker Kit (ABN 39 118 869 962) www.theloudspeakerkit.com 11 Websters
More informationHUADONG INDUSTRIAL CO.,LTD
A. Glass Beads for Road Marking Huadong TM Glass Beads are suitable for Road &Line &Pavement Marking Paints. These glass beads are specially made for used in road marling paints and thermoplastic to provide
More informationSECTION SLATE SHINGLES. 1.1 SUMMARY A. Section Includes: 1. Slate shingles over underlayment nailed to roof sheathing.
SECTION 07 31 26 SLATE SHINGLES SPEC WRITER NOTES: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Slate shingles
More informationToner Modified Bitumen-A better method of disposal of spent Toner
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 10, Issue 3 (March 2014), PP.67-72 Toner Modified Bitumen-A better method of disposal
More informationCold curing adhesive K-X280
Instructions for use English Cold curing adhesive K-X280 A4048-1.0 en English 1 Safety instructions... 3 2 General information... 3 2.1 Scope of delivery for K-X280... 3 2.2 Accessories required for installation...
More information