Advanced Transmission Lines. Transmission Line 1
|
|
- Sherilyn Fox
- 5 years ago
- Views:
Transcription
1 Advanced Transmission Lines Transmission Line 1
2 Transmission Line 2 1. Transmission Line Theory :series resistance per unit length in. :series inductance per unit length in. :shunt conductance per unit length in. :shunt capacitance per unit length in. Let : complex propagation constant. We have the solutions : positive z-direction propagation wave. : negative z-direction propagation wave. : voltage or current amplitudes of positive or negative propagation waves. Also
3 Transmission Line 3 Define characteristic impedance Then and Characteristic impedance is the voltage to current ratio of the wave. For lossless line : attenuation constant. Power loss due to (conductor loss) and (dielectric loss). : propagation constant. : phase velocity. Decreases as or increases. : guided wavelength. Decreases as or increases. : increases as increases or decreases. Terminated Lossless Transmission Line Assume incident wave, reflected wave then
4 Transmission Line 4 At, Impedance Match For it is required that. That is, the load impedance must match the characteristic impedance of the transmission line. When to Consider Transmission Line Effect When the length of the transmission line is less than 1/20th of the wavelength of the highest frequency component of a signal, then transmission line effects can be safely ignored and the circuit can be modeled as a simple RLC circuit. The actual threshold used, 1/20th, 1/10th or 1/5th, is based on experience. For example, an interconnect on a silicon chip clocking at 3 GHz has an appreciable frequency component at 15 GHz. An interconnect reaches the 1/10th threshold when it is 0.6 mm long. This is less than the dimensions of most chips, which can be up to 2 cm on a side. Thus it takes a finite time for the variation of a voltage at one end of an interconnect to impact the voltage at the other end. When an Interconnect Should be Treated as a Transmission Line Rise time 90% of its final value. : the time required for the signal to change from 10% to
5 Transmission Line 5 Time of flight delay : the time required for the signal to pass through the line where is the line length.
6 Transmission Line 6 Transmission Line Structures Figure 5 Common transmission line structures suited to planar fabrication.
7 Transmission Line 7 Typical characteristic impedance range Typical Q range
8 Transmission Line 8 Substrate Property Property of typical substrate
9 Transmission Line 9 Property of organic substrate Skin Effect Skin effect: the concentration of charge and current near the surface of a conductor. Skin depth : the depth at which the magnitude of the current falls to of its value on the surface of the conductor. For planar metal trace, thickness should be at least to reduce resistance. Larger than that is less effective. Figure 11 (a) an electromagneticwave from the left incident at the interface of air and a conductor; and (b) profiles of the electric field magnitude (top) and current magnitude (bottom) as the wave travels into the conductor.
10 Transmission Line 10
11 Transmission Line Microstrip Line Formulas, Or
12 Transmission Line 12 where Loss Dielectric loss: where Conductor loss: is the surface resistance where is the conductivity.
13 Transmission Line 13 Correction for Surface Roughness where is the attenuation of the strip without roughness, is the r.m.s. surface roughness and is the skin depth. Surface roughness increases conductor loss. Example: consider a copper microstrip, where the skin depth at 4 GHz is 1 μm. Also assume that the r.m.s. surface roughness is of similar magnitude, that is, 1 μm (typical of 99% alumina). Then. that is to say, the loss is increased by approximately 60% when surface roughness is taken into account. Bends in Microstrip Right angle bends exhibit series inductance and shunt capacitance. Insertion loss cannot be ignored at higher frequency.
14 Transmission Line 14 Example: 0.75mm line width, 0.5mm thick substrate with relative permittivity is 9.9. Equivalent circuit capacitance and inductance are pf and nh, respectively. At 10 GHz,. Mitered (Chamfered) Microstrip Bends A mitered bend produces as good as, or better, performance than curved bends. This applies to a wide range of bend angles, from up to. At least 70% chamfer fraction ( ) is recommended for an acute-angled bend of Optimum right angle bends, 60% chamfer fraction. The mitered edge of the microstrip bend acts like a reflector to redirect the current flow. Figure 16 Mitered bend. Operating frequency limits The lower-order strong coupled TM mode:
15 Transmission Line 15 The lowest-order transverse microstrip resonance: Example:,,.
16 Transmission Line Strip Line Benefit: No dispersion. Shielded. Disadvantage: Difficult to attached lumped elements. Parallel waveguide modes Formulas where. Or
17 Transmission Line 17 where. Loss where
18 Transmission Line Coplanar Waveguide (CPW) Disadvantage of Microstrip Line Relative inaccessibility of the ground plane. Difficulty associated with making shunt connections between strip and ground. Sensitivity to substrate thickness. In integrated circuit technology lateral dimensions can be defined photolithographically with great accuracy, but the substrate thickness is often not controlled at all well. Increased radiation when thick substrates are used. CPW Benefit: Easier grounding of surface-mounted (or ball grid array (BGA)- mounted) components Lower fabrication costs. No via needed. Reduced dispersion Decreased radiation losses Photo-lithographically defined structures with relatively low dependence on substrate thickness. CPW Disadvantage: Difficult in routing. Can produce unwanted common mode if asymmetric. Air bridge needed to tie the two ground to the same potential.. Insensitive to substrate thickness.
19 Transmission Line 19
20 Coupled Transmission Lines Transmission Line Structure: symmetrical, two signal wire. Support differential (odd) and common (even) modes with different characteristic impedances and phase velocities. 2. Benefit: reduce interference. 3. Disadvantage: difficult to layout. When symmetry is broken due to bend or branch, common mode will be generated, contaminating differential signals. 4. Extra consideration needed to match both differential and common modes. Example: microstrip parallel coupled line
21 Transmission Line 21 Example: Coupling: 0.05 for a length of 1/4 wavelength.t
22 Transmission Line 22
23 Transmission Line 23 Moisture Effect on Dielectric PCB constructed with a dielectric that tends to absorb moisture (such as FR4) is exposed to a humid environment for a significant amount of time, both the loss tangent and the dielectric permittivity will increase. Fig. 25 shows an example of the insertion losses measured in a dry environment such as an Arizona winter (15% RH and 60 N F) and a humid environment such as Malaysia (95% RH and 95 N F). The dramatic increase in insertion losses corresponds to an increase in dissipated power. Fig. 26 depicts measured values of the same dielectric material for both low- and high-humidity environments. At about 7.5 GHz, the increase in the loss tangent is greater than 50%. Fig. 27 shows a relatively small increase of less than 5% in the dielectric permittivity. Fig. 28 shows the measured change in insertion loss (S 21 ) at 10 GHz for a microstrip transmission line built on FR4 that was dry at beginning and then exposed to humid conditions for 55 days. In this example, the dielectric transmission-line losses at 10 GHz were 6.3 db under dry conditions at t = 0. The dielectric became almost fully saturated within the first 7 days, increasing the loss to 8.9 db. Finally, the transmission-line loss stabilized to a value of 9.3 db of loss at t = 48 days.
24 Transmission Line 24 Figure 25 Figure 26 Figure 27
25 Figure 28 Transmission Line 25
26 Differential Signaling Single-ended signaling generally work well up to approximately 1 to 2 Gb/s. As data rates increase, it becomes increasingly difficult to maintain adequate signal integrity because of system noise due to switching, crosstalk and nonideal current return paths (Fig. 1). To reduce the effect of the system noise dramatically is to dedicate a pair of transmission lines for each bit on the bus. The two transmission lines are driven in the odd mode, and the differences between the voltages are used to recover the signal at the receiver using a differential amplifier (Fig. 2 and Fig. 3). Figure 1 How system noise can severely degrade signal integrity on single-ended buses. The ideal versus noisy receiver voltages compared to the reference voltage. 1
27 Figure 2 Differential signaling where each bit is transmitted from the driver to a receiver using a pair of transmission lines driven in the odd mode. The signal is recovered at the receiver with a differential amplifier. Figure 3 Example of how common-mode noise is eliminated with differential signaling: (a) single-ended waveforms at each leg of a differential receiver showing common mode noise; (b) differential waveform. Benefits of Differential Signaling 1. Reduce common mode noise. 2. Due to the cancellation effect of the positive and negative signal pair, crosstalk of differential line is lower than single-end line for the same separation. 3. For the same reason, radiation loss is also smaller, reducing EMI. 2
28 Note: crosstalk of single-end signal line might not be higher if the same area is used (Fig. 4 and 5). Figure 4 Cross sections used to compare differential versus single-ended crosstalk: (a) two single-ended signals; (b) two differential pairs with the same pair spacing as that of the single-ended signals in (a); (c) two widely spaced single-ended signals that occupy the same board area as the differential pairs (dimensions in mils). Figure 5 Crosstalk for the cross sections in Fig. 4 demonstrating that differential signaling does not reduce crosstalk compared to single-ended signaling if the same board area is used. However, if the spacing between differential pairs is similar to the spacing between single-ended signals, crosstalk in reduced (5-in. microstrip). 3
29 Figure 6 For an odd-mode (or differential) signal, the fields orient so that an ideal virtual reference plane existed between the conductors. When the physical plane is interrupted, the virtual plane provides a continuous reference for a differential signal and helps preserve signal integrity. 4. Virtual Ground. Helpful for signal integrity when not perfect ground exists. Drawback of Differential Signaling 1. Occupy larger area. 2. Due line routing is more difficult than single line. 3. AC common-mode conversion (ACCM conversion): if the phase difference of the two signals on a differential line is not, common mode signal will be generated. Possible causes (Fig. 7): a. Length differences between the line pair. b. Asymmetric lines. c. Coupling. d. Bends. e. Termination differences 4
30 Figure 7 Examples of asymmetry in a differential pair that can cause differential to common-mode conversion: (a) routing-length differences; (b) impedance differences due to etching variation; (c) crosstalk differences; (d) length differences due to bends. Figure 8 When asymmetry exists in the differential pair, part of the signal gets converted to common mode at the receiver. 5
31 Example (Fig. 9): Calculate the common mode voltage of the following circuit. Figure 9 Example circuit for computing ACCM conversion. Figure 10 Differential common-mode conversion plotted for Fig. 9 showing that a differential signal launched at the driver becomes common mode at the receiver when the frequency is about 12.5 GHz. Fiber-Weave Effect: for example, FR4 is made from a matrix of woven bundles of fiberglass ( ) embedded in an epoxy resin ( ) as shown in Fig. 11. The glass pitch shown is typical in the printed circuit board industry. It is possible for one leg of the differential signal to be routed between glass bundles and the other to be routed over a glass bundle that effectively gives each trace a unique propagation velocity causing an imbalance in the differential pair that causes ACCM conversion. To avoid, signal traces should align with fiber at an angle. 6
32 Figure 11 A typical FR4 substrate. Example (Fig. 12): calculate the ACCM conversion of a typical case of fiber-weave effect. Figure 12 A type fiber-weave effect of FR4 substrate on ACCM converion. 7
33 Effects of ACCM Conversion of Differential Line Bends and Compensation Techniques 1. Comparison of (a) right angle bend, (b) mitered bend, (c) round corner bend and (d) and rise time 100 ps (Fig. 14 and Fig. 15). bend. Length 25 mm, signal voltage 1 V The 45-degree-angle bend structure has the minimum common-mode noise and reflected differential-mode noise. 60% lower than the right-angle bend. For common mode noise, round corner bend is a little bit better than right angle bend and mitered bend. For reflected differential-mode noise, mitered bend is the worse while round corner bend and right angle bend is similar. The faster the rise-time, the higher both the common-mode noise and reflected differential-mode noise. 8
34 Figure 14 Figure Dual Back-to-Back Bends Can reduce common mode noise from 10s mv to 1s mv. The longer separation of the dual bends, the worse the performance. Saturate above 100 mm (Fig. 17). Figure 16 Dual back to back bends 9
35 Figure 17 Remnant common-mode noise of the dual back-to-back coupled bends observed at the probing point g for various length as depicted in Fig Compensation Capacitance for Common Mode Noise Reduction (Fig. 18) The bend of the outer line can be treated as an extra capacitor to ground. A capacitor can be added on the inner line to compensate. The 1.17 pf capacitance can reduce the maximum common-mode noise by 53.48% against the uncompensated right-angle bend. 4. Compensation Patch for Common Mode Noise Reduction (Fig. 19) Due to space limitation and cost, difficult to add lumped 10
36 capacitors to compensate. Instead, use patch metal on inner bend to achieve similar capacitive effect. For the right-angle bends, a square patch of the side lengths 5.8 mm achieves 58% improvement. For 45-degree bends with a fan-shaped patch, a of 4 mm achieves 46% improvement. Figure 18 Transient analyses at the receiver for right-angle bends with shunt various compensation capacitances. 11 Figure 19 Common-mode noise of coupled bends with the parallel patch capacitance. (a) Right-angle bends with a square patch. (b) 45-degree-angle bends with a fan-shaped patch.
37 5. Slow Wave Structure Use slow wave structure on the inner line to compensate the shorter path. Figure % reduction in common mode noise. Figure 22 About 5-dB reduction in common mode noise. 6. Parasitic Trace Figure db reduction of common mode noise. 12
38 Bandwidth of Digital Signal By Fourier transform, a time-domain waveform can be thought of equivalently as being composed of the sum of infinite sinusoidal frequency components., Example: 1-GHz clock signal waveform (period 1 ns) having rise and fall times ( ) of 100 ps, a 50% duty cycle, and an amplitude of 5 V. The spectrum components are Note that because of the 50% duty cycle, the even harmonics are zero. The DC component of the waveform, is the average value of the waveform which is 2.5 V. Observe that the ninth harmonic of 9 GHz has a wavelength of 3.33 cm. To use lumped-circuit approximation to analyze a circuit driven by this frequency would require that the largest dimension of the circuit be less that 3.33mm. Similarly, to analyze a circuit that is driven by the fundamental frequency of 1 GHz, whose wavelength is 30 cm would restrict the maximum circuit dimensions to being less than 3 cm. This shows clearly that use of lumped-circuit analysis methods to 13
39 analyze a circuit having a physical dimension of, say, 3 cm that is driven by this clockwaveform would result in erroneous results for all but perhaps the fundamental frequency of the waveform. Approximate the trapezoidal pulse by finite number of harmonics It shows that the result is pretty good when up to the ninth harmonic is applied. Therefore, the required bandwidth is at least 9 GHz which is close to. Therefore, Figure 25 Approximating the clock waveform with first and third harmonics. 14
40 Figure 26 Approximating the clock waveform with first, third and fifth harmonics. Figure 27 Approximating the clock waveform with up to the ninth harmonics 15
41 Meshed-ground Plane Figure 1 Rectangular Cell Benefit: 1. Improve flexibility of FPC. 2. Improve adhesion between different metallization layers 3. Reduce weight. Figure 2 Rhombus Cell Short coming: 1. Lower operation frequency due to stop band of EBG. 2. Generate radiation due to perturbation on ground. 3. Deteriorate isolation due to holes on ground plane. Effect: 1. Reduce capacitance per unit length due to the removal of metal under transmission lines. The larger the aperture, the smaller the capacitance. 2. Increase inductance per unit length due to the perturbation of current path on ground plane. The larger the aperture, the larger the inductance. 3. Increase characteristic impedance. 4. The periodic cells create stop band. 5. Transmission line characteristics are more frequency dependent. 1
42 Benefit of rhombus cell over rectangular cell 1. Characteristic impedance is less sensitive to alignment. 2. Higher operation frequency due to the less perturbation of ground current reducing the EBG effect. Case Study: Rectangular Cell Figure 3 1. Impact of Trace-to-Aperture Intersecting Angle (Fig. 4) a. When βwas small, the response changed fast. b. curve was flattened dramatically from to. c. from to. d. Inductance and Capacitance.Solid Ground:,.. 2
43 Figure 4 Figure 5 2. Impact of Trace-to-Baseline Offset (Fig. 5) a. For, change of the offset causes large change of the capacitance, thus the impedance changes a lot.. b. For, almost no change of impedance. c. For, small change of impedance.. d. Inductance and Capacitance. Solid Ground:,. 3. Impact of Aperture Dimension (Fig. 6) a. increases when the aperture dimension increased. b. When τapproaches 1/2, the trace moved closer to the top of a row of apertures. A slight change of aperture size will make the return current distribution drastically different, leading to 3
44 significant change of. c. Forsmaller τvalues, the per-unit-length parameters changed minimally with aperture dimension changes. d. did not change much as the trace shifted if aperture size was small, e.g.. e. changed more dramatically for larger aperture sizes. f. is independent of, if the aperture size to trace width ratio is smaller than 1/2. g. Inductance and Capacitance. Solid Ground:,. Figure 6 Figure 7 4
45 4. Impact of aperture-to-aperture separation (Fig. 7) a. decreased as b increased for different. b. As b increased, approaching solid reference conductor case. c. changed slightly faster for the no trace offset situation compared to the trace offset cases. d. Inductance and Capacitance. Solid Ground:,. Case Study: Rhombus Cell Line width: 0.36 mm. Substrate thickness: 0.2 mm. Substrate dielectric constant: Line offset effect (Fig. 8) a. The middle case provides the shortest return current path, thus the best transmitting performance b. The center and the edge cases have the longest return current 5
46 path, thus have poor characteristics. c. Cutoff at about 6 GHz due to EBG effect except the middle case. The cutoff of the middle case is about twice of the other case because the effective cell size is half. 2. Cell Size Effect (Fig. 9) a. As cell size increases, cutoff frequency decreases. Figure 8 Figure 9 Figure Improving performance by adding a trace on ground plan (Fig. 10) 6
47 a. A straight current path is generated on ground plane to reduce EBG effect. b. 10, 15 and 20 TG cases maintain -3-dB insertion loss over the 10 GHz, which show almost ideal characteristics of the general microstrip line. 7
Introduction: Planar Transmission Lines
Chapter-1 Introduction: Planar Transmission Lines 1.1 Overview Microwave integrated circuit (MIC) techniques represent an extension of integrated circuit technology to microwave frequencies. Since four
More informationMicrocircuit Electrical Issues
Microcircuit Electrical Issues Distortion The frequency at which transmitted power has dropped to 50 percent of the injected power is called the "3 db" point and is used to define the bandwidth of the
More informationCHAPTER 2 MICROSTRIP REFLECTARRAY ANTENNA AND PERFORMANCE EVALUATION
43 CHAPTER 2 MICROSTRIP REFLECTARRAY ANTENNA AND PERFORMANCE EVALUATION 2.1 INTRODUCTION This work begins with design of reflectarrays with conventional patches as unit cells for operation at Ku Band in
More informationLow Jitter, Low Emission Timing Solutions For High Speed Digital Systems. A Design Methodology
Low Jitter, Low Emission Timing Solutions For High Speed Digital Systems A Design Methodology The Challenges of High Speed Digital Clock Design In high speed applications, the faster the signal moves through
More informationDifferential Signaling is the Opiate of the Masses
Differential Signaling is the Opiate of the Masses Sam Connor Distinguished Lecturer for the IEEE EMC Society 2012-13 IBM Systems & Technology Group, Research Triangle Park, NC My Background BSEE, University
More informationToday I would like to present a short introduction to microstrip cross-coupled filter design. I will be using Sonnet em to analyze my planar circuit.
Today I would like to present a short introduction to microstrip cross-coupled filter design. I will be using Sonnet em to analyze my planar circuit. And I will be using our optimizer, EQR_OPT_MWO, in
More informationSignal/Power Integrity Analysis of High-Speed Memory Module with Meshed Reference Plane 1
, pp.119-128 http//dx.doi.org/10.14257/ijca.2018.11.7.10 Signal/Power Integrity Analysis of High-Speed Memory Module with Meshed Reference Plane 1 Moonjung Kim Institute of IT Convergence Technology, Dept.
More informationDesign Guide for High-Speed Controlled Impedance Circuit Boards
IPC-2141A ASSOCIATION CONNECTING ELECTRONICS INDUSTRIES Design Guide for High-Speed Controlled Impedance Circuit Boards Developed by the IPC Controlled Impedance Task Group (D-21c) of the High Speed/High
More informationDesign and experimental realization of the chirped microstrip line
Chapter 4 Design and experimental realization of the chirped microstrip line 4.1. Introduction In chapter 2 it has been shown that by using a microstrip line, uniform insertion losses A 0 (ω) and linear
More informationLines and Slotlines. Microstrip. Third Edition. Ramesh Garg. Inder Bahl. Maurizio Bozzi ARTECH HOUSE BOSTON LONDON. artechhouse.
Microstrip Lines and Slotlines Third Edition Ramesh Garg Inder Bahl Maurizio Bozzi ARTECH HOUSE BOSTON LONDON artechhouse.com Contents Preface xi Microstrip Lines I: Quasi-Static Analyses, Dispersion Models,
More informationELEC Course Objectives/Proficiencies
Lecture 1 -- to identify (and list examples of) intentional and unintentional receivers -- to list three (broad) ways of reducing/eliminating interference -- to explain the differences between conducted/radiated
More informationApplication Note 5525
Using the Wafer Scale Packaged Detector in 2 to 6 GHz Applications Application Note 5525 Introduction The is a broadband directional coupler with integrated temperature compensated detector designed for
More informationINVENTION DISCLOSURE- ELECTRONICS SUBJECT MATTER IMPEDANCE MATCHING ANTENNA-INTEGRATED HIGH-EFFICIENCY ENERGY HARVESTING CIRCUIT
INVENTION DISCLOSURE- ELECTRONICS SUBJECT MATTER IMPEDANCE MATCHING ANTENNA-INTEGRATED HIGH-EFFICIENCY ENERGY HARVESTING CIRCUIT ABSTRACT: This paper describes the design of a high-efficiency energy harvesting
More informationFaster than a Speeding Bullet
BEYOND DESIGN Faster than a Speeding Bullet by Barry Olney IN-CIRCUIT DESIGN PTY LTD AUSTRALIA In a previous Beyond Design column, Transmission Lines, I mentioned that a transmission line does not carry
More informationIndex Terms Microstrip patch antenna, Quarter wave inset feed, Coaxial cable feed, Gain, Bandwidth, Directivity, Radiation pattern.
PERFORMANCE ANALYSIS OF RECTANGULAR PATCH ANTENNA USING QUARTER WAVE FEED LINE AND COAXIAL FEED LINE METHODS FOR C- BAND RADAR BASED APPLICATIONS Dr.H.C.Nagaraj 1, Dr.T.S.Rukmini 2, Mr.Prasanna Paga 3,
More informationBASIS OF ELECTROMAGNETIC COMPATIBILITY OF INTEGRATED CIRCUIT Chapter VI - MODELLING PCB INTERCONNECTS Corrections of exercises
BASIS OF ELECTROMAGNETIC COMPATIBILITY OF INTEGRATED CIRCUIT Chapter VI - MODELLING PCB INTERCONNECTS Corrections of exercises I. EXERCISE NO 1 - Spot the PCB design errors Spot the six design errors in
More informationChapter 4. Problems. 1 Chapter 4 Problem Set
1 Chapter 4 Problem Set Chapter 4 Problems 1. [M, None, 4.x] Figure 0.1 shows a clock-distribution network. Each segment of the clock network (between the nodes) is 5 mm long, 3 µm wide, and is implemented
More informationMatched Length Matched Delay
by Barry Olney column BEYOND DESIGN Matched Delay In previous columns, I have discussed matched length routing and how matched length does not necessarily mean matched delay. But, all design rules, specified
More informationCompact Distributed Phase Shifters at X-Band Using BST
Integrated Ferroelectrics, 56: 1087 1095, 2003 Copyright C Taylor & Francis Inc. ISSN: 1058-4587 print/ 1607-8489 online DOI: 10.1080/10584580390259623 Compact Distributed Phase Shifters at X-Band Using
More informationChapter 3 Broadside Twin Elements 3.1 Introduction
Chapter 3 Broadside Twin Elements 3. Introduction The focus of this chapter is on the use of planar, electrically thick grounded substrates for printed antennas. A serious problem with these substrates
More informationA VIEW OF ELECTROMAGNETIC LIFE ABOVE 100 MHz
A VIEW OF ELECTROMAGNETIC LIFE ABOVE 100 MHz An Experimentalist's Intuitive Approach Lothar O. (Bud) Hoeft, PhD Consultant, Electromagnetic Effects 5012 San Pedro Ct., NE Albuquerque, NM 87109-2515 (505)
More informationDemystifying Vias in High-Speed PCB Design
Demystifying Vias in High-Speed PCB Design Keysight HSD Seminar Mastering SI & PI Design db(s21) E H What is Via? Vertical Interconnect Access (VIA) An electrical connection between layers to pass a signal
More informationChapter 12: Transmission Lines. EET-223: RF Communication Circuits Walter Lara
Chapter 12: Transmission Lines EET-223: RF Communication Circuits Walter Lara Introduction A transmission line can be defined as the conductive connections between system elements that carry signal power.
More informationinsert link to the published version of your paper
Citation Niels Van Thienen, Wouter Steyaert, Yang Zhang, Patrick Reynaert, (215), On-chip and In-package Antennas for mm-wave CMOS Circuits Proceedings of the 9th European Conference on Antennas and Propagation
More informationObjectives of transmission lines
Introduction to Transmission Lines Applications Telephone Cable TV (CATV, or Community Antenna Television) Broadband network High frequency (RF) circuits, e.g., circuit board, RF circuits, etc. Microwave
More informationA Signal Integrity Measuring Methodology in the Extraction of Wide Bandwidth Environmental Coefficients
As originally published in the IPC APEX EXPO Conference Proceedings. A Signal Integrity Measuring Methodology in the Extraction of Wide Bandwidth Environmental Coefficients Eric Liao, Kuen-Fwu Fuh, Annie
More informationVLSI is scaling faster than number of interface pins
High Speed Digital Signals Why Study High Speed Digital Signals Speeds of processors and signaling Doubled with last few years Already at 1-3 GHz microprocessors Early stages of terahertz Higher speeds
More informationPDN Probes. P2100A/P2101A Data Sheet. 1-Port and 2-Port 50 ohm Passive Probes
P2100A/P2101A Data Sheet PDN Probes 1-Port and 2-Port 50 ohm Passive Probes power integrity PDN impedance testing ripple PCB resonances transient step load stability and NISM noise TDT/TDR clock jitter
More informationMicrowave Engineering
Microwave Circuits 1 Microwave Engineering 1. Microwave: 300MHz ~ 300 GHz, 1 m ~ 1mm. a. Not only apply in this frequency range. The real issue is wavelength. Historically, as early as WWII, this is the
More informationTexas Instruments DisplayPort Design Guide
Texas Instruments DisplayPort Design Guide April 2009 1 High Speed Interface Applications Introduction This application note presents design guidelines, helping users of Texas Instruments DisplayPort devices
More informationDesign Fundamentals by A. Ciccomancini Scogna, PhD Suppression of Simultaneous Switching Noise in Power and Ground Plane Pairs
Design Fundamentals by A. Ciccomancini Scogna, PhD Suppression of Simultaneous Switching Noise in Power and Ground Plane Pairs Photographer: Janpietruszka Agency: Dreamstime.com 36 Conformity JUNE 2007
More informationHigh Speed Digital Systems Require Advanced Probing Techniques for Logic Analyzer Debug
JEDEX 2003 Memory Futures (Track 2) High Speed Digital Systems Require Advanced Probing Techniques for Logic Analyzer Debug Brock J. LaMeres Agilent Technologies Abstract Digital systems are turning out
More informationPlane Crazy, Part 2 BEYOND DESIGN. by Barry Olney
by Barry Olney column BEYOND DESIGN Plane Crazy, Part 2 In my recent four-part series on stackup planning, I described the best configurations for various stackup requirements. But I did not have the opportunity
More informationA Dual-Polarized MIMO Antenna with EBG for 5.8 GHz WLAN Application
Progress In Electromagnetics Research Letters, Vol. 51, 15 2, 215 A Dual-Polarized MIMO Antenna with EBG for 5.8 GHz WLAN Application Xiaoyan Zhang 1, 2, *, Xinxing Zhong 1,BinchengLi 3, and Yiqiang Yu
More informationChapter 7 Design of the UWB Fractal Antenna
Chapter 7 Design of the UWB Fractal Antenna 7.1 Introduction F ractal antennas are recognized as a good option to obtain miniaturization and multiband characteristics. These characteristics are achieved
More informationPCB Crosstalk Simulation Toolkit Mark Sitkowski Design Simulation Systems Ltd Based on a paper by Ladd & Costache
PCB Crosstalk Simulation Toolkit Mark Sitkowski Design Simulation Systems Ltd www.designsim.com.au Based on a paper by Ladd & Costache Introduction Many of the techniques used for the modelling of PCB
More informationDesigns of Substrate Integrated Waveguide (SIW) and Its Transition to Rectangular Waveguide. Ya Guo
Designs of Substrate Integrated Waveguide (SIW) and Its Transition to Rectangular Waveguide by Ya Guo A thesis submitted to the Graduate Faculty of Auburn University in partial fulfillment of the requirements
More informationCOMPACT PLANAR MICROSTRIP CROSSOVER FOR BEAMFORMING NETWORKS
Progress In Electromagnetics Research C, Vol. 33, 123 132, 2012 COMPACT PLANAR MICROSTRIP CROSSOVER FOR BEAMFORMING NETWORKS B. Henin * and A. Abbosh School of ITEE, The University of Queensland, QLD 4072,
More informationAntenna Theory and Design
Antenna Theory and Design Antenna Theory and Design Associate Professor: WANG Junjun 王珺珺 School of Electronic and Information Engineering, Beihang University F1025, New Main Building wangjunjun@buaa.edu.cn
More informationPCB Material Selection for High-speed Digital Designs. Add a subtitle
PCB Material Selection for High-speed Digital Designs Add a subtitle Outline Printed Circuit Boards (PCBs) for Highspeed Digital (HSD) applications PCB factors that limit High-speed Digital performance
More informationCHAPTER 4. Practical Design
CHAPTER 4 Practical Design The results in Chapter 3 indicate that the 2-D CCS TL can be used to synthesize a wider range of characteristic impedance, flatten propagation characteristics, and place passive
More informationDesign of Microstrip Coupled Line Bandpass Filter Using Synthesis Technique
Design of Microstrip Coupled Line Bandpass Filter Using Synthesis Technique 1 P.Priyanka, 2 Dr.S.Maheswari, 1 PG Student, 2 Professor, Department of Electronics and Communication Engineering Panimalar
More informationA 6 : 1 UNEQUAL WILKINSON POWER DIVIDER WITH EBG CPW
Progress In Electromagnetics Research Letters, Vol. 8, 151 159, 2009 A 6 : 1 UNEQUAL WILKINSON POWER DIVIDER WITH EBG CPW C.-P. Chang, C.-C. Su, S.-H. Hung, and Y.-H. Wang Institute of Microelectronics,
More informationEMC Design Guidelines C4ISR EQUIPMENT & SYSTEMS
EMC Design Guidelines C4ISR EQUIPMENT & SYSTEMS 1.1. SHIELDING Enclosed structure (equipment box or chassis in outside RF environment) should provide at least 100 db of RF shielding at 1 MHz, 40 db at
More informationMutual Coupling between Two Patches using Ideal High Impedance Surface
International Journal of Electronics and Communication Engineering. ISSN 0974-2166 Volume 4, Number 3 (2011), pp. 287-293 International Research Publication House http://www.irphouse.com Mutual Coupling
More informationChapter 2. Literature Review
Chapter 2 Literature Review 2.1 Development of Electronic Packaging Electronic Packaging is to assemble an integrated circuit device with specific function and to connect with other electronic devices.
More informationEMC Simulation of Consumer Electronic Devices
of Consumer Electronic Devices By Andreas Barchanski Describing a workflow for the EMC simulation of a wireless router, using techniques that can be applied to a wide range of consumer electronic devices.
More informationKeysight Technologies Signal Integrity Tips and Techniques Using TDR, VNA and Modeling
Keysight Technologies Signal Integrity Tips and Techniques Using, VNA and Modeling Article Reprint This article first appeared in the March 216 edition of Microwave Journal. Reprinted with kind permission
More informationHigh-Selectivity UWB Filters with Adjustable Transmission Zeros
Progress In Electromagnetics Research Letters, Vol. 52, 51 56, 2015 High-Selectivity UWB Filters with Adjustable Transmission Zeros Liang Wang *, Zhao-Jun Zhu, and Shang-Yang Li Abstract This letter proposes
More informationThe Effects of PCB Fabrication on High-Frequency Electrical Performance
As originally published in the IPC APEX EXPO Conference Proceedings. The Effects of PCB Fabrication on High-Frequency Electrical Performance John Coonrod, Rogers Corporation Advanced Circuit Materials
More informationThe Effects of PCB Fabrication on High-Frequency Electrical Performance
The Effects of PCB Fabrication on High-Frequency Electrical Performance John Coonrod, Rogers Corporation Advanced Circuit Materials Division Achieving optimum high-frequency printed-circuit-board (PCB)
More informationThe shunt capacitor is the critical element
Accurate Feedthrough Capacitor Measurements at High Frequencies Critical for Component Evaluation and High Current Design A shielded measurement chamber allows accurate assessment and modeling of low pass
More informationOptimization of Wafer Level Test Hardware using Signal Integrity Simulation
June 7-10, 2009 San Diego, CA Optimization of Wafer Level Test Hardware using Signal Integrity Simulation Jason Mroczkowski Ryan Satrom Agenda Industry Drivers Wafer Scale Test Interface Simulation Simulation
More informationPractical Design Considerations for Dense, High-Speed, Differential Stripline PCB Routing Related to Bends, Meanders and Jog-outs
Practical Design Considerations for Dense, High-Speed, Differential Stripline PCB Routing Related to Bends, Meanders and Jog-outs AUTHORS Michael J. Degerstrom, Mayo Clinic degerstrom.michael@mayo.edu
More informationWide-Band Bandpass Filter Using CRLH Transmission Line and Floating Slot Approach
Available online at www.sciencedirect.com Procedia Technology 4 (2012 ) 466 471 C3IT-2012 Wide-Band Bandpass Filter Using CRLH Transmission Line and Floating Slot Approach Pratik Mondal a, A.Roy a, S.K.Parui
More informationPIEZOELECTRIC TRANSFORMER FOR INTEGRATED MOSFET AND IGBT GATE DRIVER
1 PIEZOELECTRIC TRANSFORMER FOR INTEGRATED MOSFET AND IGBT GATE DRIVER Prasanna kumar N. & Dileep sagar N. prasukumar@gmail.com & dileepsagar.n@gmail.com RGMCET, NANDYAL CONTENTS I. ABSTRACT -03- II. INTRODUCTION
More informationPCB Design Guidelines for GPS chipset designs. Section 1. Section 2. Section 3. Section 4. Section 5
PCB Design Guidelines for GPS chipset designs The main sections of this white paper are laid out follows: Section 1 Introduction Section 2 RF Design Issues Section 3 Sirf Receiver layout guidelines Section
More informationChapter-2 LOW PASS FILTER DESIGN 2.1 INTRODUCTION
Chapter-2 LOW PASS FILTER DESIGN 2.1 INTRODUCTION Low pass filters (LPF) are indispensable components in modern wireless communication systems especially in the microwave and satellite communication systems.
More informationSignal and Noise Measurement Techniques Using Magnetic Field Probes
Signal and Noise Measurement Techniques Using Magnetic Field Probes Abstract: Magnetic loops have long been used by EMC personnel to sniff out sources of emissions in circuits and equipment. Additional
More informationRelationship Between Signal Integrity and EMC
Relationship Between Signal Integrity and EMC Presented by Hasnain Syed Solectron USA, Inc. RTP, North Carolina Email: HasnainSyed@solectron.com 06/05/2007 Hasnain Syed 1 What is Signal Integrity (SI)?
More informationThe Basics of Patch Antennas, Updated
The Basics of Patch Antennas, Updated By D. Orban and G.J.K. Moernaut, Orban Microwave Products www.orbanmicrowave.com Introduction This article introduces the basic concepts of patch antennas. We use
More informationAnalysis of Microstrip Circuits Using a Finite-Difference Time-Domain Method
Analysis of Microstrip Circuits Using a Finite-Difference Time-Domain Method M.G. BANCIU and R. RAMER School of Electrical Engineering and Telecommunications University of New South Wales Sydney 5 NSW
More informationCustom Interconnects Fuzz Button with Hardhat Test Socket/Interposer 1.00 mm pitch
Custom Interconnects Fuzz Button with Hardhat Test Socket/Interposer 1.00 mm pitch Measurement and Model Results prepared by Gert Hohenwarter 12/14/2015 1 Table of Contents TABLE OF CONTENTS...2 OBJECTIVE...
More informationInset Fed Microstrip Patch Antenna for X-Band Applications
Inset Fed Microstrip Patch Antenna for X-Band Applications Pradeep H S Dept.of ECE, Siddaganga Institute of Technology, Tumakuru, Karnataka. Abstract Microstrip antennas play an important role in RF Communication.
More informationMODIFIED MILLIMETER-WAVE WILKINSON POWER DIVIDER FOR ANTENNA FEEDING NETWORKS
Progress In Electromagnetics Research Letters, Vol. 17, 11 18, 2010 MODIFIED MILLIMETER-WAVE WILKINSON POWER DIVIDER FOR ANTENNA FEEDING NETWORKS F. D. L. Peters, D. Hammou, S. O. Tatu, and T. A. Denidni
More informationCOMPACT FRACTAL MONOPOLE ANTENNA WITH DEFECTED GROUND STRUCTURE FOR WIDE BAND APPLICATIONS
COMPACT FRACTAL MONOPOLE ANTENNA WITH DEFECTED GROUND STRUCTURE FOR WIDE BAND APPLICATIONS 1 M V GIRIDHAR, 2 T V RAMAKRISHNA, 2 B T P MADHAV, 3 K V L BHAVANI 1 M V REDDIAH BABU, 1 V SAI KRISHNA, 1 G V
More informationHigh efficient PIFA-L Bend antenna for MIMO based Mobile Handsets
IOSR Journal of Electronics and Communication Engineering (IOSR-JECE) e-issn: 2278-2834,p- ISSN: 2278-8735.Volume 9, Issue 1, Ver. II (Jan. 2014), PP 71-75 High efficient PIFA-L Bend antenna for MIMO based
More informationThe Facts about the Input Impedance of Power and Ground Planes
The Facts about the Input Impedance of Power and Ground Planes The following diagram shows the power and ground plane structure of which the input impedance is computed. Figure 1. Configuration of the
More informationMiniaturized Wilkinson Power Divider with nth Harmonic Suppression using Front Coupled Tapered CMRC
ACES JOURNAL, VOL. 28, NO. 3, MARCH 213 221 Miniaturized Wilkinson Power Divider with nth Harmonic Suppression using Front Coupled Tapered CMRC Mohsen Hayati 1,2, Saeed Roshani 1,3, and Sobhan Roshani
More informationMethodology for MMIC Layout Design
17 Methodology for MMIC Layout Design Fatima Salete Correra 1 and Eduardo Amato Tolezani 2, 1 Laboratório de Microeletrônica da USP, Av. Prof. Luciano Gualberto, tr. 3, n.158, CEP 05508-970, São Paulo,
More informationSignal Integrity Design of TSV-Based 3D IC
Signal Integrity Design of TSV-Based 3D IC October 24, 21 Joungho Kim at KAIST joungho@ee.kaist.ac.kr http://tera.kaist.ac.kr 1 Contents 1) Driving Forces of TSV based 3D IC 2) Signal Integrity Issues
More informationPlastic straw: future of high-speed signaling
Supplementary Information for Plastic straw: future of high-speed signaling Ha Il Song, Huxian Jin, and Hyeon-Min Bae * Korea Advanced Institute of Science and Technology (KAIST), Department of Electrical
More informationWaveguides. Metal Waveguides. Dielectric Waveguides
Waveguides Waveguides, like transmission lines, are structures used to guide electromagnetic waves from point to point. However, the fundamental characteristics of waveguide and transmission line waves
More informationAN-1364 APPLICATION NOTE
APPLICATION NOTE One Technology Way P.O. Box 916 Norwood, MA 262-916, U.S.A. Tel: 781.329.47 Fax: 781.461.3113 www.analog.com Differential Filter Design for a Receive Chain in Communication Systems by
More informationVol. 55 No. 7. Founded in 1958 mwjournal.com. July 2012
Vol. 55 No. 7 Founded in 1958 mwjournal.com July 212 Comparing Microstrip and CPW Performance By building a better electromagnetic (EM) simulation model, which includes the effects of a PCB s metal surface
More informationChapter 12 Digital Circuit Radiation. Electromagnetic Compatibility Engineering. by Henry W. Ott
Chapter 12 Digital Circuit Radiation Electromagnetic Compatibility Engineering by Henry W. Ott Forward Emission control should be treated as a design problem from the start, it should receive the necessary
More informationDesign of 2 1 Square Microstrip Antenna Array
International Journal of Engineering and Manufacturing Science. ISSN 2249-3115 Volume 8, Number 1 (2018) pp. 89-94 Research India Publications http://www.ripublication.com Design of 2 1 Square Microstrip
More informationHigh-Speed Circuit Board Signal Integrity
High-Speed Circuit Board Signal Integrity For a listing of recent titles in the Artech House Microwave Library, turn to the back of this book. High-Speed Circuit Board Signal Integrity Stephen C. Thierauf
More informationCharacterization of Printed Circuit Board Material & Manufacturing Technology for High Frequency
As originally published in the IPC APEX EXPO Conference Proceedings. Characterization of Printed Circuit Board Material & Manufacturing Technology for High Frequency AT&S Leoben, Austria Oliver Huber 1,
More informationHigh Performance Signaling. Jan Rabaey
High Performance Signaling Jan Rabaey Sources: Introduction to Digital Systems Engineering, Bill Dally, Cambridge Press, 1998. Circuits, Interconnections and Packaging for VLSI, H. Bakoglu, Addison-Wesley,
More informationPredicting and Controlling Common Mode Noise from High Speed Differential Signals
Predicting and Controlling Common Mode Noise from High Speed Differential Signals Bruce Archambeault, Ph.D. IEEE Fellow, inarte Certified Master EMC Design Engineer, Missouri University of Science & Technology
More informationTECHNICAL REPORT: CVEL Parasitic Inductance Cancellation for Filtering to Chassis Ground Using Surface Mount Capacitors
TECHNICAL REPORT: CVEL-14-059 Parasitic Inductance Cancellation for Filtering to Chassis Ground Using Surface Mount Capacitors Andrew J. McDowell and Dr. Todd H. Hubing Clemson University April 30, 2014
More informationEMC problems from Common Mode Noise on High Speed Differential Signals
EMC problems from Common Mode Noise on High Speed Differential Signals Bruce Archambeault, PhD Alma Jaze, Sam Connor, Jay Diepenbrock IBM barch@us.ibm.com 1 Differential Signals Commonly used for high
More informationEC6011-ELECTROMAGNETICINTERFERENCEANDCOMPATIBILITY
EC6011-ELECTROMAGNETICINTERFERENCEANDCOMPATIBILITY UNIT-3 Part A 1. What is an opto-isolator? [N/D-16] An optoisolator (also known as optical coupler,optocoupler and opto-isolator) is a semiconductor device
More informationMicrostrip Lines and Slotlines
Microstrip Lines and Slotlines Second Edition K.C. Gupta Ramesh Garg Inder Bahl Prakash Bhartia Artech House Boston London Contents Preface to the Second Edition Preface to the First Edition Chapter 1
More informationFuzz Button interconnects at microwave and mm-wave frequencies
Fuzz Button interconnects at microwave and mm-wave frequencies David Carter * The Connector can no Longer be Ignored. The connector can no longer be ignored in the modern electronic world. The speed of
More informationA MINIATURIZED OPEN-LOOP RESONATOR FILTER CONSTRUCTED WITH FLOATING PLATE OVERLAYS
Progress In Electromagnetics Research C, Vol. 14, 131 145, 21 A MINIATURIZED OPEN-LOOP RESONATOR FILTER CONSTRUCTED WITH FLOATING PLATE OVERLAYS C.-Y. Hsiao Institute of Electronics Engineering National
More informationCHAPTER 4 DESIGN OF BROADBAND MICROSTRIP ANTENNA USING PARASITIC STRIPS WITH BAND-NOTCH CHARACTERISTIC
CHAPTER 4 DESIGN OF BROADBAND MICROSTRIP ANTENNA USING PARASITIC STRIPS WITH BAND-NOTCH CHARACTERISTIC 4.1 INTRODUCTION Wireless communication technology has been developed very fast in the last few years.
More informationBill Ham Martin Ogbuokiri. This clause specifies the electrical performance requirements for shielded and unshielded cables.
098-219r2 Prepared by: Ed Armstrong Zane Daggett Bill Ham Martin Ogbuokiri Date: 07-24-98 Revised: 09-29-98 Revised again: 10-14-98 Revised again: 12-2-98 Revised again: 01-18-99 1. REQUIREMENTS FOR SPI-3
More informationLowpass and Bandpass Filters
Microstrip Filters for RF/Microwave Applications. Jia-Sheng Hong, M. J. Lancaster Copyright 2001 John Wiley & Sons, Inc. ISBNs: 0-471-38877-7 (Hardback); 0-471-22161-9 (Electronic) CHAPTER 5 Lowpass and
More informationMICROWAVE ENGINEERING-II. Unit- I MICROWAVE MEASUREMENTS
MICROWAVE ENGINEERING-II Unit- I MICROWAVE MEASUREMENTS 1. Explain microwave power measurement. 2. Why we can not use ordinary diode and transistor in microwave detection and microwave amplification? 3.
More informationVaractor Loaded Transmission Lines for Linear Applications
Varactor Loaded Transmission Lines for Linear Applications Amit S. Nagra ECE Dept. University of California Santa Barbara Acknowledgements Ph.D. Committee Professor Robert York Professor Nadir Dagli Professor
More informationHigh-Speed PCB Design und EMV Minimierung
TRAINING Bei dem hier beschriebenen Training handelt es sich um ein Cadence Standard Training. Sie erhalten eine Dokumentation in englischer Sprache. Die Trainingssprache ist deutsch, falls nicht anders
More information(i) Determine the admittance parameters of the network of Fig 1 (f) and draw its - equivalent circuit.
I.E.S-(Conv.)-1995 ELECTRONICS AND TELECOMMUNICATION ENGINEERING PAPER - I Some useful data: Electron charge: 1.6 10 19 Coulomb Free space permeability: 4 10 7 H/m Free space permittivity: 8.85 pf/m Velocity
More informationReview on Various Issues and Design Topologies of Edge Coupled Coplanar Waveguide Filters
Review on Various Issues and Design Topologies of Edge Coupled Coplanar Waveguide Filters Manoj Kumar *, Ravi Gowri Department of Electronics and Communication Engineering Graphic Era University, Dehradun,
More informationTHROUGHOUT the last several years, many contributions
244 IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS, VOL. 6, 2007 Design and Analysis of Microstrip Bi-Yagi and Quad-Yagi Antenna Arrays for WLAN Applications Gerald R. DeJean, Member, IEEE, Trang T. Thai,
More informationPCB Routing Guidelines for Signal Integrity and Power Integrity
PCB Routing Guidelines for Signal Integrity and Power Integrity Presentation by Chris Heard Orange County chapter meeting November 18, 2015 1 Agenda Insertion Loss 101 PCB Design Guidelines For SI Simulation
More informationLowpass Filters. Microwave Filter Design. Chp5. Lowpass Filters. Prof. Tzong-Lin Wu. Department of Electrical Engineering National Taiwan University
Microwave Filter Design Chp5. Lowpass Filters Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University Lowpass Filters Design steps Select an appropriate lowpass filter prototype
More informationDesign and Demonstration of a Passive, Broadband Equalizer for an SLED Chris Brinton, Matthew Wharton, and Allen Katz
Introduction Design and Demonstration of a Passive, Broadband Equalizer for an SLED Chris Brinton, Matthew Wharton, and Allen Katz Wavelength Division Multiplexing Passive Optical Networks (WDM PONs) have
More informationDesigning external cabling for low EMI radiation A similar article was published in the December, 2004 issue of Planet Analog.
HFTA-13.0 Rev.2; 05/08 Designing external cabling for low EMI radiation A similar article was published in the December, 2004 issue of Planet Analog. AVAILABLE Designing external cabling for low EMI radiation
More information