Analysis of Class-DE Amplifier With Linear and Nonlinear Shunt Capacitances at 25% Duty Ratio
|
|
- Egbert Harmon
- 5 years ago
- Views:
Transcription
1 2334 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 57, NO. 9, SEPTEMBER 2010 Analysis of Class-DE Amplifier With Linear and Nonlinear Shunt Capacitances at 25% Duty Ratio Hiroo Sekiya, Member, IEEE, Natsumi Sagawa, and Marian K. Kazimierczuk, Fellow, IEEE Abstract The class-e zero-voltage switching/zero-derivative switching operation within class-de amplifiers can be easily achieved by adding external shunt capacitances. This paper gives the analytical expressions for the designs of the class-de amplifiers with the shunt capacitances composed of linear and nonlinear capacitances for any grading coefficient of MOSFET body junction diodes at the switch-on duty ratio.in the analysis, an equivalent linear shunt capacitance of the nonlinear MOSFET drain source parasitic capacitances is derived. Analytical results show good agreements with the simulation and experimental ones, which validate our analysis. Index Terms Class-DE power amplifier, class-e zero-voltage switching (ZVS)/zero-derivative switching (ZDS) conditions, equivalent linear shunt capacitance, high efficiency, nonlinear MOSFET drain source parasitic capacitance. I. INTRODUCTION T HE CLASS-DE power amplifier [1] [10] is one of the high-efficiency power amplifiers. By adding shunt capacitances to MOSFETs of the class-d amplifier, the class-de amplifier satisfies the class-e zero-voltage switching (ZVS) and zero-derivative switching (ZDS) conditions, yielding high efficiency at high frequencies. It is known that the highest operating frequency of the class-de amplifier is obtained for the 25% switch-on duty ratio [4]. For the design of the class-de amplifiers, the operating frequency is one of the most important specifications. In the case of low-frequency operation, the shunt-capacitance values should be very high. Conversely, the shunt capacitances should be low for high-frequency operation. The minimum shunt capacitances are the drain source parasitic capacitances of MOSFETs, which depend on the kind of MOSFETs. However, the degrees of freedom for the design are reduced when the shunt capacitances consist of only the parasitic capacitances of the MOSFETs. For example, when the operating frequency, dc-supply voltage, and output power are specified, the values Manuscript received August 12, 2009; revised December 15, 2009; accepted January 26, Date of publication March 15, 2010; date of current version October 01, The work of H. Sekiya was supported by the Japan Society for the Promotion of Science. This paper was recommended by Associate Editor E. Alarcon. H. Sekiya and N. Sagawa are with the Graduate School of Advanced Integration Science, Chiba University, Chiba , Japan, ( sekiya@faculty.chiba-u.jp). M. K. Kazimierczuk is with the Department of Electrical Engineering, Wright State University, Dayton, OH USA. Digital Object Identifier /TCSI of shunt capacitances are determined uniquely [8], [10]. Therefore, designers have to look for MOSFETs whose drain source parasitic capacitances are matched with the required values. However, it is not an easy task. For this reason, generally, external capacitances are added in parallel to the MOSFETs in order to adjust the shunt-capacitance values. Because of the adjustment of the shunt capacitance, it becomes easy to design the class-de amplifiers with fixed operating frequency, dc-supply voltage, and output power. For low-frequency operation, the shunt-capacitance values are large. In this case, the effects of the MOSFET drain source parasitic capacitances can be neglected because the values of MOSFET drain source parasitic capacitances are small. On the other hand, the effects of the MOSFET drain source parasitic capacitances increase as the operating frequency becomes high. The problem is that the MOSFET drain source parasitic capacitances are nonlinear and the external ones are linear [8] [20]. We should consider both the nonlinearity and linearity of the shunt capacitances in order to design the class-de amplifiers for high-frequency operation. The class-de amplifiers analyzed until now have only the linear shunt capacitances [1], [2] or only the nonlinear ones [7] [10]. It is important to derive analytical expressions for the class-de amplifier with the shunt capacitances composed of the linear and nonlinear shunt capacitances. A similar problem appears in the class-e amplifier. References [11] [18] gave the analytical expressions for the class-e amplifier with the nonlinear shunt capacitance only and the linear and nonlinear shunt capacitances, which present the effective analytical techniques for the problem of this paper. This paper, which was previously presented in part at the 2009 IEEE International Symposium on Circuits and Systems (ISCAS 2009) [20] 1, gives analytical expressions for the designs of the class-de amplifiers with the shunt capacitances composed of linear and nonlinear capacitances for any grading coefficient at the 25% switch-on duty ratio. The obtained expressions include the results for the case of not only both the linear and nonlinear shunt capacitances, but also the linear or nonlinear shunt capacitances only. In the analysis, an equivalent linear shunt capacitance of the nonlinear MOSFET drain source parasitic capacitances is obtained. By using the value of the equivalent linear shunt capacitance, the values of the external shunt capacitances are determined easily. In the design equations, a numerical calculation is needed for obtaining the resonant-inductor value. However, this numerical calculation is replaced with an approximate fixedvalue.byusingthefixed value, it 1 In the paper of ISCAS 2009, only the analysis for was presented. In this paper, the analysis is carried out for any grading coefficient along with new design examples and experimental results /$ IEEE
2 SEKIYA et al.: ANALYSIS OF CLASS-DE AMPLIFIER WITH SHUNT CAPACITANCES AT 25% DUTY RATIO 2335 Fig. 1. Class-DE amplifier. (a) Circuit topology. (b) Equivalent circuit. is possible to obtain the design values from only the analytical expressions. Analytical results show good agreements with the simulation and experimental ones, which indicate the validity of our analysis. In the Appendix, perturbation analysis is presented in order to obtain the power conversion efficiency for the class-de amplifier with linear and nonlinear shunt capacitances, following the analysis procedure in [1] and [5] [8]. II. FUNDAMENTAL OPERATION OF THE CLASS-DE AMPLIFIER Fig. 1 shows the circuit topology of the class-de amplifier [1] [10]. This amplifier consists of two switching devices and, e.g., MOSFETs, the shunt capacitances and, and series-resonant circuit. The inductance is divided into and. The elements and realize a series tuned circuit with its resonant frequency equal to the operating frequency. The phase shift of the output current is obtained by. Fig. 2 shows the example waveforms of the class-de amplifier for the nominal operation at the duty ratio. Both the switches turn ON and OFF alternately. During one cycle of class-de amplifier operation, there are two dead-time intervals when both switches are OFF. In the dead-time intervals, the voltage across one switch decreases and reaches zero when the switch turns ON. In addition, the slope of the voltage across each switch is also zero at the turn-on instant, i.e., These conditions are called the class-e ZVS and ZDS conditions. The dead-time intervals are required to recharge the shunt capacitances. Because of the dead-time and the class-e ZVS/ZDS conditions, the switching power losses of the MOS- FETs of class-de amplifier are zero. Therefore, the high drain efficiency can be achieved at high frequencies. The class-de amplifier satisfies the class-e ZVS/ZDS conditions by adding the shunt capacitances and to the MOSFETs in the (1) (2) Fig. 2. Nominal waveform of the class-de amplifier for. class-d amplifier. Usually, the shunt capacitances are realized by the sum of the external linear capacitances and the MOSFET nonlinear drain source parasitic capacitances. III. CIRCUIT ANALYSIS A. Assumptions The analysis in this paper is based on the following assumptions. 1) Both MOSFETs are identical, and each MOSFET is modeled as an ideal switch and a drain source parasitic capacitance connected in parallel. The drain source parasitic capacitances of the MOSFETs are expressed as and (3) In (3), is the drain-to-source voltage; is the built-in potential, which typically ranges from 0.5 to 0.9 V; is the capacitance at ;and is the grading coefficient of the diode junction of the MOSFET [7] [14], which is in the range. According to the assumption of the identical MOS- FETs,,,and are valid. 2) The identical linear shunt capacitances are connected to both MOSFETs in parallel, which are expressed as. 3) All passive elements except the MOSFET drain source parasitic capacitances are linear elements and do not have parasitic resistances.
3 2336 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 57, NO. 9, SEPTEMBER 2010 TABLE I SWITCHING PATTERN IN CLASS-DE AMPLIFIER From (4) and (7) (9), the current through switch as is obtained (10) Time Interval: interval. Therefore : Both switches are OFF in this 4) The loaded-quality factor of the resonant circuit is high enough to generate pure sinusoidal output current. The current through the circuit and load resistance is sinusoidal at the operating frequency From (3), (5), (6), and,wehave (11) (4) where represents the angular time. Usually, the loaded quality factor is defined as. In this paper, however, the definition of is used because of the simple derivations of the load-network-component values. 5) The ideal resonant filter with the resonant frequency is realized by and. 6) The switch-on duty ratio is 0.25, and the switching patternisgivenintablei. Using the aforementioned assumptions, the equivalent circuit of the class-de amplifier is obtained, as shown in Fig. 1(b). From (12), the following can be derived: (12) (13) B. Expressions for Waveforms The analysis for a steady state is performed in the interval. The following relation between and is always valid: The switch voltage is zero at due to the class-e ZVS condition in (2). Therefore, from (13), the amplitude is obtained as The slope of the switch voltage expressed as (5) at dead-time intervals is By substituting (14) into (13), we can obtain (14) (6) Hence, using the class-e ZDS condition in (1), we obtain and. Since the amplitude of the output current is positive, the phase difference is (7) Similarly, (7) is valid for to satisfy the class-e ZDS condition in (2). Time Interval: : Since is ON and is OFF, the switch voltages in this interval are constant and shunt capaci- In addition, the current through switch tances is (8) (9) (15) It is impossible to solve (15) for analytically, but possible to do that numerically. From (15), we can obtain important information that the normalized switch voltages and are expressed as functions of the ratio of the dc-supply voltage to the built-in potential, the ratio of the linear shunt capacitances and the drain source parasitic capacitances, the grading coefficient, and the angular time.
4 SEKIYA et al.: ANALYSIS OF CLASS-DE AMPLIFIER WITH SHUNT CAPACITANCES AT 25% DUTY RATIO 2337 The output power is obtained from (14) (19) Fig. 3. Example waveforms of normalized switch voltage for and. Time Interval: : Because of the symmetrical operations of the switches with respect to,theswitch voltages and currents have the following relationships for : (16) Fig. 3 shows the example waveforms of the normalized switch voltage for and,whichis computed by applying Newton s method to (15). In this figure, makes the shunt capacitances practically linear. The waveforms in Fig. 3 can be obtained for the proper designs. The purpose of the designs is to obtain the elemental values that provide the waveforms in Fig. 3. C. Power Relations and Equivalent Linear Capacitances of MOSFET Drain Source Parasitic Capacitances Note that the average value of the current through the shunt capacitance is always zero at any. Therefore, the dc-supply current is analytically obtained from the average value of the supply current flowing from the dc voltage source as where is the amplitude of the output voltage. The power losses never occur because of the assumptions of ideal switching operations and no parasitic resistance. Therefore, we can write (20) From (18) (20), we can obtain the relation between the dc-supply voltage and the amplitude of the output voltage as (21) This equation means that the amplitude of the output voltage increases in proportion to the increase of the dc-supply voltage and is independent of the grading coefficient. From (21), the output power can be rewritten using From (19) and (22), the following relation is obtained: (22) (23) Here, we define the equivalent linear capacitance as a linear shunt capacitance, which can be substituted for the nonlinear MOSFET drain source parasitic capacitance to satisfy the class-e ZVS/ZDS at the same values of,, and [11], [13], [14]. From (23), it is obtained (24) Generally,,,and are uniquely determined by the MOSFET. In addition,,,and are obtained from the specified conditions. From (23) and (24), we can calculate that satisfies the class-e ZVS/ZDS conditions. It is shown that the external linear shunt capacitances are very useful to adjust the waveforms for satisfying the class-e ZVS/ZDS conditions. D. Voltage Across Resonant-Circuit Reactance The fundamental component of the voltage reactance is across the (17) (25) From (17), the dc-supply power is obtained as where (18) (26)
5 2338 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 57, NO. 9, SEPTEMBER 2010 TABLE II PARAMETERS OF EACH MOSFET Fig. 5. Normalized nonlinear shunt capacitances and normalized equivalent linear shunt capacitances as a function of the switch voltage for V. Fig. 4. Characteristics of for, 0.25, 0.5, and (a) As a function of for fixed. (b) As a function of for. Because of the assumptions on the high- and the ideal resonant filter, the fundamental-frequency component of the switch voltage is Hence the normalized magnitude analysis (27) (28) is obtained from the Fourier (29) We cannot obtain the analytical expression of this integration. Here, the coefficient is defined as functions of and at fixed. From Fig. 4(a), the value of increases with the increase in and. However, the differences among them are small. In Fig. 4(a), all plots are within the 5% difference of the linear-shunt-capacitance case, i.e.,. From Fig. 4(b), it is shown that increases with the decrease in for fixed, which is also confirmed in Fig. 4(a). When increases, the values of for any converge to that for.this is because nonlinearities of shunt capacitances are suppressed with the increase in. E. Load Network Components From (22), the load resistance is given as Using the definition of the loaded-quality factor the resonant capacitance as (31),weobtain The external shunt capacitance is obtained from (23) and (24) (32) (30) (33) which is obtained numerically. Since the normalized switch voltage is a function of,,and, is also a function of them. Fig. 4 shows the plots for as From,,and, we can obtain numerically. From Assumption 5), the ideal resonant filter with the resonant frequency is realized by and.from
6 SEKIYA et al.: ANALYSIS OF CLASS-DE AMPLIFIER WITH SHUNT CAPACITANCES AT 25% DUTY RATIO 2339 TABLE III ANALYTICAL PREDICTIONS AND EXPERIMENTAL MEASUREMENTS Fig. 6. Normalized equivalent linear shunt capacitances as a function of. The measured efficiencies. values are used for the calculations of power conversion Fig. 8. Driver circuit for 25% duty ratio. From (21), (26), and (30), the inductance is given as (35) From (34) and (35), the resonant inductance is obtained as (36) Fig. 7. External shunt capacitances. (a) As a function of the switch voltage at MHz. (b) As a function of the operating frequency for V. and (32), the resonant capacitance expressed analytically as is (34) If the loaded-quality factor is defined as, is needed in order to obtain. However, the value of is a function of.whenwedefine the loaded-quality factor as, we can obtain without. This is a reason for the change in the definition of. In these design equations, only should be obtained numerically, which affects the value of. We should note that the analysis in this paper is based on the assumption of high-, which is usually. In addition, the values of are within a few percent difference from. Therefore, for simplicity, it is allowed to put for all cases.
7 2340 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 57, NO. 9, SEPTEMBER 2010 Fig. 9. Waveforms by PSPICE simulations and circuit experiments. (i) 2SK2504 MOSFETs. (ii) IRFZ24N MOSFETs. (iii) IRF530 MOSFETs. (a) PSPICEsimulation results. (b) Experimental results. (Horizontal) 100 ns/div. (Vertical) :5V/div; and : 20 V/div; and : 10 V/div. IV. DISCUSSIONS AND DESIGN EXAMPLES The design examples by using three kinds of the discrete MOSFET devices are given. In the design examples, the MOSFETs of 2SK2504 manufactured by Rohm, IRFZ24N, and IRF530 by International Rectifier are used as the switching devices. The built-in potentials, the grading coefficients,and can be obtained from the SPICE model [19], as shown in TableII.Thevaluesof,,,and correspond to those of VJ, M, CJ0, and RS in the MOSFET SPICE models, respectively. Note that each MOSFET has a different value of.the load resistance is given as a design specification. Fig. 5 shows the normalized nonlinear shunt capacitances and the normalized equivalent linear shunt capacitances as a function of the switch voltage for V. is symmetrical with respect to V. This symmetry generally occurs because is always valid. From this figure, it is shown that the normalized shunt capacitances decrease with the Fig. 10. Equivalent circuit of the class-de amplifier with ESRs. increase in the grading coefficient. The grading coefficient is an important parameter to design the class-de amplifier. Fig. 6 shows the normalized equivalent linear shunt capacitance as a function of the ratio of dc-supply voltage to the built-in potential for satisfying the class-e ZVS/ZDS conditions. These plots are obtained from (24). From
8 SEKIYA et al.: ANALYSIS OF CLASS-DE AMPLIFIER WITH SHUNT CAPACITANCES AT 25% DUTY RATIO 2341 this figure, it is shown that the normalized equivalent linear shunt capacitances decrease as the dc-supply voltage increases. In particular, they vary rapidly for small. Fig. 7(a) shows the external shunt capacitances as a function of for satisfying the class-e ZVS/ZDS conditions at MHz. These plots are obtained from (33). The total shunt capacitances are independent of the dc-supply voltage from (33). In addition, the equivalent linear shut capacitances decrease as the dc-supply voltage increases, as shown in Fig. 6. Therefore, the external shunt capacitances increase with the increase in the dc-supply voltage. From Fig. 7(a), we can confirm that the value of external shunt capacitance depends on the MOSFETs. The external shunt capacitances become almost constant for large. Fig. 7(b) shows the external shunt capacitances as a function of the operating frequency for satisfying the class-e ZVS/ZDS conditions at V. The external shunt capacitances decrease with the increase in the operating frequency. It can be seen that the maximum frequency is obtained when the external shunt capacitance is zero. From (23) and (24), the maximum frequency is obtained as (37) This expression is very similar to that for the class-e amplifier [18]. The maximum frequency depends on the MOSFETs, which are 10.6 MHz for 2SK2504, 9.55 MHz for IRFZ24N, and 3.75 MHz for IRF530. For the circuit experiments, the class-de amplifiers were designed for the operating frequency MHz, the dc-supply voltage V, the load resistance,andthe loaded-quality factor. Using these specifications, we can obtain pf from (32). Here, the design with 2SK2504 is considered. The external capacitance is obtained as pf from (24). From,,and, is obtained numerically. By using this value, is determined from (36). Table III gives the elemental values for all MOSFETs. In these design specifications, the resonant inductances for all MOSFETs are within since the values of are almost the same as 0.5. In addition, the driver signals with 25% switch-on duty ratio are generated from the driver circuit, as shown in Fig. 8, in the circuit experiments. Fig. 9 shows the simulated waveforms obtained by PSPICE and the experimental ones. In addition, Table III gives the analytical predictions and experimental measurements. In this table, the element values were measured by the HP-4284A LCR meter. Both the simulated and experimental waveforms are satisfied with the class-e ZVS/ZDS conditions. These results indicate the validity of the analysis in this paper. The laboratory measurements showed more than 94% efficiency for all MOSFETs. The analytical derivation of the power conversion efficiencies is shown in the Appendix. V. CONCLUSION This paper has presented the analytical expressions for the designs of class-de amplifier with shunt capacitances composed of linear and nonlinear capacitances for any grading coefficient at the 25% switch-on duty ratio. In the analysis, an equivalent linear shunt capacitance of nonlinear MOSFET drain source parasitic capacitance is defined. The analytical results have shown good agreements with the simulation and experimental ones, which validate our analysis. APPENDIX PERTURBATION ANALYSIS In real circuits, power losses occur in the equivalent series resistance (ESR) of each component. Fig. 10 shows the equivalent circuit of the class-de amplifier with ESRs, where and are the MOSFET on-resistances and the ESR of the series-resonant-circuit elements and, respectively. Generally, the ESRs of the MOSFET drain source parasitic capacitances and the external shunt capacitances and are much lower than the other ESRs. In addition, the current through the shunt capacitances is shared by the MOSFET drain source parasitic capacitances and the external shunt capacitances. Therefore, the power dissipations at the ESRs of shunt capacitances are negligible. It is assumed that the ESR of the resonant inductor and the switch on-resistances are much lower than the load resistance [1], [8]. In this case, the voltage and current waveforms are not significantly affected by the ESR and the switch on-resistance. The power losses in ESRs of the switch on-resistance and the series-resonant circuit are From (38), the power conversion efficiency obtained (38) is approximately (39) REFERENCES [1] H. Koizumi, T. Suetsugu, M. Fujii, K. Shinoda, S. Mori, and K. Ikeda, Class DE high-efficiency tuned power amplifier, IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 43, no. 1, pp , Jan [2] S. A. El-Hamamsy, Design of high-efficiency RF class-d power amplifier, IEEE Trans. Power Electron., vol. 9, no. 3, pp , May 1994.
9 2342 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 57, NO. 9, SEPTEMBER 2010 [3] K. Shinoda, T. Suetsugu, M. Matsuo, and S. Mori, Idealized operation of the class DE amplifier and frequency multipliers, IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 45, no. 1, pp , Jan [4] M. Albulet, An exact analysis of class-de amplifier at any output, IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 46, no. 10, pp , Oct [5] M. Matsuo, T. Suetsugu, S. Mori, and I. Sasase, Class DE currentsource parallel resonant inverter, IEEE Trans. Ind. Electron., vol.46, no. 2, pp , Apr [6]H.Sekiya,H.Koizumi,S.Mori,I.Sasase,J.Lu,andT.Yahagi, FM/PWM control scheme in class DE inverter, IEEE Trans. Circuits Syst.I,Reg.Papers, vol. 51, no. 7, pp , Jul [7] L. R. Neorne, Design of a 2.5-MHz, soft-switching, class-d converter for electrodeless lighting, IEEE Trans. Power Electron., vol. 12, no. 3, pp , May [8] H. Sekiya, T. Watanabe, T. Suetsugu, and M. K. Kazimierczuk, Analysis and design of class DE amplifier with nonlinear capacitances, IEEE Trans. Circuits Syst. I, Reg. Papers, vol. 56, no. 10, pp , Oct [9] H. Sekiya, N. Sagawa, and M. K. Kazimierczuk, Analysis of class DE amplifier with nonlinear shunt capacitances at any grading coefficient for high and 25% duty ratio, IEEE Trans. Power Electron., tobe published. [10] T. Ezawa, H. Sekiya, and T. Yahagi, Design of class DE amplifier with nonlinear shunt capacitances for any output, IEICE Trans. Fundam., vol. E91-A, no. 4, pp , Apr [11] N. O. Sokal and R. Redl, Power transistor output port model, RF Des., vol. 10, no. 6, pp , Jun [12] M. J. Chudobiak, The use of parasitic nonlinear capacitors in class E amplifiers, IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 41, no. 12, pp , Dec [13] A. Mediano, P. Molina, and J. Navarro, Class E RF/microwave power amplifier: Linear equivalent of transistor s nonlinear output capacitance, normalized design and maximum operating frequency versus output capacitance, in IEEEMTT-SInt.Microw.Symp.Dig., Boston, MA, Jun. 2000, pp [14] T. Suetsugu and M. K. Kazimierczuk, Comparison of class-e amplifier with nonlinear and linear shunt capacitance, IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 50, no. 8, pp , Aug [15] T. Suetsugu and M. K. Kazimierczuk, Analysis and design of class E amplifier with shunt capacitance composed of nonlinear and linear capacitances, IEEETrans.CircuitsSyst.I,Reg.Papers, vol. 51, no. 7, pp , Jul [16] H. Sekiya, Y. Arifuku, H. Hase, J. Lu, and T. Yahagi, Investigation of class E amplifier with nonlinear capacitance for any output and finite DC-feed inductance, IEICE Trans. Fundam., vol. E89-A, no. 4, pp , Apr [17] A. Mediano, P. M. Gaudó, and C. Bernal, Design of class E amplifier with nonlinear and linear shunt capacitances for any duty cycle, IEEE Trans. Microw. Theory Tech., vol. 55, no. 3, pp , Mar [18] A. Mediano and P. Molina, Frequency limitation of a high-efficiency class E tuned RF power amplifier due to a shunt capacitance, in IEEE MTT-S Int. Microw. Symp., Anaheim, CA, Jun. 1999, pp [19] R. M. Kielkowski, SPICE: Practical Device Modeling. New York: McGraw-Hill, [20] H. Sekiya, R. Miyahara, and M. K. Kazimierczuk, Design of class-de amplifier with linear and nonlinear shunt capacitances for 25% duty ratio, in Proc. IEEE ISCAS, Taipei, Taiwan, May 2009, pp Hiroo Sekiya (S 97 M 01) was born in Tokyo, Japan, on July 5, He received the B.E., M.E., and Ph.D. degrees in electrical engineering from Keio University, Yokohama, Japan, in 1996, 1998, and 2001, respectively. Since April 2001, he has been with Chiba University, Chiba, Japan, where he is currently an Assistant Professor with the Graduate School of Advanced Integration Science. From 2008 to 2010, he was a Visiting Scholar at the Department of Electrical Engineering, Wright State University, Dayton, OH. His research interests include high-frequency high-efficiency tuned power amplifiers, resonant dc/dc power converters, dc/ac inverters, and digital signal processing for wireless communication. Dr. Sekiya is a member of the Institute of Electronics, Information and Communication Engineers (IEICE), Japan, the Information Processing Society of Japan, the Society Information Theory and Its Application, Japan, and the Research Institute of Signal Processing, Japan. Natsumi Sagawa was born in Fukushima, Japan, on January 26, She received the B.E. degree from Chiba University, Chiba, Japan, in 2008, where she is currently working toward the M.E. degree in the Graduate School of Advanced Integration Science. Her research interests include high-frequency resonant dc/dc power converter and dc/ac inverter. Marian K. Kazimierczuk (M 91 SM 91 F 04) received the M.S., Ph.D., and D.Sci. degrees in electronics engineering from the Department of Electronics, Technical University of Warsaw, Warsaw, Poland, in 1971, 1978, and 1984, respectively. He was a Teaching and Research Assistant from 1972 to 1978 and an Assistant Professor from 1978 to 1984 with the Institute of Radio Electronics, Department of Electronics, Technical University of Warsaw. In 1984, he was a Project Engineer with Design Automation, Inc., Lexington, MA. From 1984 to 1985, he was a Visiting Professor at the Department of Electrical Engineering, Virginia Polytechnic Institute and State University, Blacksburg. Since 1985, he has been with the Department of Electrical Engineering, Wright State University, Dayton, OH, where he is currently a Professor. His research interests are in high-frequency high-efficiency switching-mode tuned power amplifiers, resonant and pulsewidth modulation dc/dc power converters, dc/ac inverters, high-frequency rectifiers, electronic ballasts, modeling and control of converters, high-frequency magnetics, and power semiconductor devices. He was an Associate Editor for the Journal of Circuits, Systems, and Computers. Prof. Kazimierczuk was the recipient of the IEEE Harrell V. Noble Award for his contributions to the fields of aerospace, industrial, and power electronics in He is an Associate Editor of the IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS (CAS) I: REGULAR PAPERS. He was a member of the Superconductivity Committee of the IEEE Power Electronics Society. He was the Chair of the CAS Technical Committee of Power Systems and Power Electronics Circuits in He is a member of Tau Beta Pi.
THE CLASS DE inverter [1] [8] has become an increasingly
1250 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 51, NO. 7, JULY 2004 FM/PWM Control Scheme in Class DE Inverter Hiroo Sekiya, Member, IEEE, Hirotaka Koizumi, Member, IEEE, Shinsaku
More informationBy Hiroo Sekiya, Chiba University, Chiba, Japan and Marian K. Kazimierzuk, Wright State University, Dayton, OH
ISSUE: November 2011 Core Geometry Coefficient For Resonant Inductors* By Hiroo Sekiya, Chiba University, Chiba, Japan and Marian K. Kazimierzuk, Wright State University, Dayton, OH A resonant inductor
More informationDesign of Class-E M Power Amplifier Taking into Account Auxiliary Circuit
Design of Class-E M Power Amplifier Taking into Account Auxiliary Circuit Ryosuke MIYAHARA,HirooSEKIYA, and Marian K. KAZIMIERCZUK Dept. of Information and Image Science, Chiba University -33, Yayoi-cho,
More informationDesign of a High-Efficiency Class DE Tuned Power Oscillator
IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: FUNDAMENTAL THEORY AND APPLICATIONS, VOL. 47, NO., NOVEMBER 2000 645 which is determined by trial-and-error, yielded the highest convergence rate. V. CONCLUSIONS
More informationDesign of High PAE Class-E Power Amplifier For Wireless Power Transmission
This article has been accepted and published on J-STAGE in advance of copyediting. Content is final as presented. IEICE Electronics Express, Vol.*, No.*, 1 8 Design of High PAE Class-E Power Amplifier
More informationCLASS E zero-voltage-switching (ZVS) resonant power
1684 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 52, NO. 8, AUGUST 2005 Design of Symmetrical Class E Power Amplifiers for Very Low Harmonic-Content Applications Siu-Chung Wong, Member,
More informationwith FM and PWM Control Hiroo Sekiyay, Shinsaku Moriz and Iwao Sasasey y Dept. of Electrical Engineering, Keio Univercity,
Exact Analysis of Class DE Amplier with FM and PWM Control Hiroo Sekiyay, Shinsaku Moriz and Iwao Sasasey y Dept. of Electrical Engineering, Keio Univercity, 3141, Hiyoshi, Kohoku, Yokohama, 35 JAPAN Phone:
More informationAnalysis and Synthesis of phemt Class-E Amplifiers with Shunt Inductor including ON-State Active-Device Resistance Effects
Analysis and Synthesis of phemt Class-E Amplifiers with Shunt Inductor including ON-State Active-Device Resistance Effects Thian, M., & Fusco, V. (2006). Analysis and Synthesis of phemt Class-E Amplifiers
More informationOptimum Mode Operation and Implementation of Class E Resonant Inverter for Wireless Power Transfer Application
Optimum Mode Operation and Implementation of Class E Resonant Inverter for Wireless Power Transfer Application Monalisa Pattnaik Department of Electrical Engineering National Institute of Technology, Rourkela,
More informationCLASS E switching-mode circuits [1] [35] have
JOURNAL OF L A TEX CLASS FILES, VOL. 6, NO. 1, JANUARY 27 1 Design Procedure for Class E Switching Circuits Allowing Implicit Circuit Equations Hiroo Sekiya, Member, IEEE,, Toru Ezawa, and Yuichi Tanji,
More informationNovel Soft-Switching DC DC Converter with Full ZVS-Range and Reduced Filter Requirement Part I: Regulated-Output Applications
184 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 2, MARCH 2001 Novel Soft-Switching DC DC Converter with Full ZVS-Range and Reduced Filter Requirement Part I: Regulated-Output Applications Rajapandian
More informationModelling of Closed Loop Class E Inverter Based Induction Heater
Research Journal of Applied Sciences, Engineering and Technology 3(1): 15-21, 2011 ISSN: 2040-7467 Maxwell Scientific Organization, 2011 Received: September 08, 2010 Accepted: December 02, 2010 Published:
More informationAnalysis and Design of Class-E Switching Circuits for Inductively Coupled Wireless Power Transfer Systems. January 2015
Analysis and Design of Class-E Switching Circuits for Inductively Coupled Wireless Power Transfer Systems January 215 Tomoharu Nagashima Graduate School of Advanced Integration Science CHIBA UNIVERSITY
More informationIEEE Transactions On Circuits And Systems Ii: Express Briefs, 2007, v. 54 n. 12, p
Title A new switched-capacitor boost-multilevel inverter using partial charging Author(s) Chan, MSW; Chau, KT Citation IEEE Transactions On Circuits And Systems Ii: Express Briefs, 2007, v. 54 n. 12, p.
More informationTwo-output Class E Isolated dc-dc Converter at 5 MHz Switching Frequency 1 Z. Pavlović, J.A. Oliver, P. Alou, O. Garcia, R.Prieto, J.A.
Two-output Class E Isolated dc-dc Converter at 5 MHz Switching Frequency 1 Z. Pavlović, J.A. Oliver, P. Alou, O. Garcia, R.Prieto, J.A. Cobos Universidad Politécnica de Madrid Centro de Electrónica Industrial
More informationIN A CONTINUING effort to decrease power consumption
184 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 1, JANUARY 1999 Forward-Flyback Converter with Current-Doubler Rectifier: Analysis, Design, and Evaluation Results Laszlo Huber, Member, IEEE, and
More informationRECENTLY, the harmonics current in a power grid can
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 2, MARCH 2008 715 A Novel Three-Phase PFC Rectifier Using a Harmonic Current Injection Method Jun-Ichi Itoh, Member, IEEE, and Itsuki Ashida Abstract
More informationGeneralized Design Considerations and Analysis of Class-E Amplifier for Sinusoidal and Square Input Voltage Waveforms
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS Generalized Design Considerations and Analysis of Class-E Amplifier for Sinusoidal and Square Input Voltage Waveforms Mohsen Hayati, Ali Lotfi, Marian K. Kazimierczuk,
More informationPARALLELING of converter power stages is a wellknown
690 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 4, JULY 1998 Analysis and Evaluation of Interleaving Techniques in Forward Converters Michael T. Zhang, Member, IEEE, Milan M. Jovanović, Senior
More informationA New Soft Recovery PWM Quasi-Resonant Converter With a Folding Snubber Network
456 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 49, NO. 2, APRIL 2002 A New Soft Recovery PWM Quasi-Resonant Converter With a Folding Snubber Network Jin-Kuk Chung, Student Member, IEEE, and Gyu-Hyeong
More information466 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 3, MAY A Single-Switch Flyback-Current-Fed DC DC Converter
466 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 3, MAY 1998 A Single-Switch Flyback-Current-Fed DC DC Converter Peter Mantovanelli Barbosa, Member, IEEE, and Ivo Barbi, Senior Member, IEEE Abstract
More informationHARMONIC contamination, due to the increment of nonlinear
612 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 44, NO. 5, OCTOBER 1997 A Series Active Power Filter Based on a Sinusoidal Current-Controlled Voltage-Source Inverter Juan W. Dixon, Senior Member,
More informationImproving Passive Filter Compensation Performance With Active Techniques
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 50, NO. 1, FEBRUARY 2003 161 Improving Passive Filter Compensation Performance With Active Techniques Darwin Rivas, Luis Morán, Senior Member, IEEE, Juan
More informationClass D Series Resonant Converter Controlled with FPGA-Based Delta-Sigma Modulator
Class D Series Resonant Converter Controlled with FPGA-Based Delta-Sigma Modulator Hirotaka Koizumi Department of Electrical Engineering Tokyo University of Science Chiyoda-ku, Tokyo 102-0073 JAPAN E-mail:
More informationNovel Zero-Current-Switching (ZCS) PWM Switch Cell Minimizing Additional Conduction Loss
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 49, NO. 1, FEBRUARY 2002 165 Novel Zero-Current-Switching (ZCS) PWM Switch Cell Minimizing Additional Conduction Loss Hang-Seok Choi, Student Member, IEEE,
More informationIN recent years, the development of high power isolated bidirectional
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 2, MARCH 2008 813 A ZVS Bidirectional DC DC Converter With Phase-Shift Plus PWM Control Scheme Huafeng Xiao and Shaojun Xie, Member, IEEE Abstract The
More informationControlling a DC-DC Converter by using the power MOSFET as a voltage controlled resistor
Controlling a DC-DC Converter by using the power MOSFET as a voltage controlled resistor Author Smith, T., Dimitrijev, Sima, Harrison, Barry Published 2000 Journal Title IEEE Transactions on Circuits and
More informationTHE CONVENTIONAL voltage source inverter (VSI)
134 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 1, JANUARY 1999 A Boost DC AC Converter: Analysis, Design, and Experimentation Ramón O. Cáceres, Member, IEEE, and Ivo Barbi, Senior Member, IEEE
More informationWITH THE development of high brightness light emitting
1410 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 3, MAY 2008 Quasi-Active Power Factor Correction Circuit for HB LED Driver Kening Zhou, Jian Guo Zhang, Subbaraya Yuvarajan, Senior Member, IEEE,
More informationAdaptive Off-Time Control for Variable-Frequency, Soft-Switched Flyback Converter at Light Loads
596 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 17, NO. 4, JULY 2002 Adaptive Off-Time Control for Variable-Frequency, Soft-Switched Flyback Converter at Light Loads Yuri Panov and Milan M. Jovanović,
More informationIN THE high power isolated dc/dc applications, full bridge
354 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 2, MARCH 2006 A Novel Zero-Current-Transition Full Bridge DC/DC Converter Junming Zhang, Xiaogao Xie, Xinke Wu, Guoliang Wu, and Zhaoming Qian,
More informationA Novel Single-Stage Push Pull Electronic Ballast With High Input Power Factor
770 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 48, NO. 4, AUGUST 2001 A Novel Single-Stage Push Pull Electronic Ballast With High Input Power Factor Chang-Shiarn Lin, Member, IEEE, and Chern-Lin
More informationA Highly Efficient Broadband Class-E Power Amplifier with Nonlinear Shunt Capacitance
JOURNAL OF ELECTROMAGNETIC ENGINEERING AND SCIENCE, VOL. 17, NO. 4, 221~227, OCT. 2017 https://doi.org/10.26866/jees.2017.17.4.221 ISSN 2234-8395 (Online) ISSN 2234-8409 (Print) A Highly Efficient Broadband
More informationPush-Pull Class-E Power Amplifier with a Simple Load Network Using an Impedance Matched Transformer
Proceedings of the International Conference on Electrical, Electronics, Computer Engineering and their Applications, Kuala Lumpur, Malaysia, 214 Push-Pull Class-E Power Amplifier with a Simple Load Network
More informationSoft Switched Resonant Converters with Unsymmetrical Control
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 10, Issue 1 Ver. I (Jan Feb. 2015), PP 66-71 www.iosrjournals.org Soft Switched Resonant Converters
More informationTHE DESIGN of microwave filters is based on
IEEE TRANSACTIONS ON MICROWAVE THEORY AND TECHNIQUES, VOL. 46, NO. 4, APRIL 1998 343 A Unified Approach to the Design, Measurement, and Tuning of Coupled-Resonator Filters John B. Ness Abstract The concept
More informationA Double ZVS-PWM Active-Clamping Forward Converter: Analysis, Design, and Experimentation
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 6, NOVEMBER 2001 745 A Double ZVS-PWM Active-Clamping Forward Converter: Analysis, Design, and Experimentation René Torrico-Bascopé, Member, IEEE, and
More informationMOST electrical systems in the telecommunications field
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 46, NO. 2, APRIL 1999 261 A Single-Stage Zero-Voltage Zero-Current-Switched Full-Bridge DC Power Supply with Extended Load Power Range Praveen K. Jain,
More informationAPPLICATION OF GENERAL-PURPOSE CIRCUIT SIMULATORS
APPLICATION OF GENERAL-PURPOSE CIRCUIT SIMULATORS TO AUTOMATED DESIGN AND INVESTIGATION OF CLASS E POWER AMPLIFIERS Olga Jorova Antonova, Marin Hristov Hristov, Elissaveta Dimitrova Gadjeva Faculty of
More informationResistance Compression Networks for Radio-Frequency Power Conversion
Resistance Compression Networks for Radio-Frequency Power Conversion The MIT Faculty has made this article openly available. Please share how this access benefits you. Your story matters. Citation As Published
More informationDC-DC Resonant converters with APWM control
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) ISSN: 2278-1676 Volume 2, Issue 5 (Sep-Oct. 2012), PP 43-49 DC-DC Resonant converters with APWM control Preeta John 1 Electronics Department,
More informationPrecise Analytical Solution for the Peak Gain of LLC Resonant Converters
680 Journal of Power Electronics, Vol. 0, No. 6, November 200 JPE 0-6-4 Precise Analytical Solution for the Peak Gain of LLC Resonant Converters Sung-Soo Hong, Sang-Ho Cho, Chung-Wook Roh, and Sang-Kyoo
More informationH-BRIDGE system used in high power dc dc conversion
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 1, JANUARY 2008 353 Quasi Current Mode Control for the Phase-Shifted Series Resonant Converter Yan Lu, K. W. Eric Cheng, Senior Member, IEEE, and S.
More informationSteady-State Simulation and Optimization of Class-E Power Amplifiers With Extended Impedance Method
IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL 58, NO 6, JUNE 2011 1433 Steady-State Simulation and Optimization of Class-E Power Amplifiers With Extended Impedance Method Junrui Liang,
More informationSingle-Wire Current-Share Paralleling of Current-Mode-Controlled DC Power Supplies
780 IEEE TRANSACTION ON INDUSTRIAL ELECTRONICS, VOL. 47, NO. 4, AUGUST 2000 Single-Wire Current-Share Paralleling of Current-Mode-Controlled DC Power Supplies Chang-Shiarn Lin and Chern-Lin Chen, Senior
More informationStability and Dynamic Performance of Current-Sharing Control for Paralleled Voltage Regulator Modules
172 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 17, NO. 2, MARCH 2002 Stability Dynamic Performance of Current-Sharing Control for Paralleled Voltage Regulator Modules Yuri Panov Milan M. Jovanović, Fellow,
More information3.1 ignored. (a) (b) (c)
Problems 57 [2] [3] [4] S. Modeling, Analysis, and Design of Switching Converters, Ph.D. thesis, California Institute of Technology, November 1976. G. WESTER and R. D. MIDDLEBROOK, Low-Frequency Characterization
More informationCOMMON mode current due to modulation in power
982 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 5, SEPTEMBER 1999 Elimination of Common-Mode Voltage in Three-Phase Sinusoidal Power Converters Alexander L. Julian, Member, IEEE, Giovanna Oriti,
More informationA High-Frequency Resonant Inverter Topology With Low- Voltage Stress
A High-Frequency Resonant Inverter Topology With Low- Voltage Stress The MIT Faculty has made this article openly available. Please share how this access benefits you. Your story matters. Citation Rivas,
More informationINSULATED gate bipolar transistors (IGBT s) are widely
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 4, JULY 1998 601 Zero-Voltage and Zero-Current-Switching Full-Bridge PWM Converter Using Secondary Active Clamp Jung-Goo Cho, Member, IEEE, Chang-Yong
More informationSwitching Behavior of Class-E Power Amplifier and Its Operation Above Maximum Frequency
Switching Behavior of Class-E Power Amplifier and Its Operation Above Maximum Frequency Seunghoon Jee, Junghwan Moon, Student Member, IEEE, Jungjoon Kim, Junghwan Son, and Bumman Kim, Fellow, IEEE Abstract
More informationDesign and simulation of Parallel circuit class E Power amplifier
International Journal of scientific research and management (IJSRM) Volume 3 Issue 7 Pages 3270-3274 2015 \ Website: www.ijsrm.in ISSN (e): 2321-3418 Design and simulation of Parallel circuit class E Power
More informationLOW PEAK CURRENT CLASS E RESONANT FULL-WAVE LOW dv/dt RECTIFIER DRIVEN BY A VOLTAGE GENERATOR
Électronique et transmission de l information LOW PEAK CURRENT CLASS E RESONANT FULL-WAVE LOW dv/dt RECTIFIER DRIVEN BY A VOLTAGE GENERATOR ŞERBAN BÎRCĂ-GĂLĂŢEANU 1 Key words : Power Electronics, Rectifiers,
More informationPARALLEL coupled-line filters are widely used in microwave
2812 IEEE TRANSACTIONS ON MICROWAVE THEORY AND TECHNIQUES, VOL. 53, NO. 9, SEPTEMBER 2005 Improved Coupled-Microstrip Filter Design Using Effective Even-Mode and Odd-Mode Characteristic Impedances Hong-Ming
More informationDesign of Resistive-Input Class E Resonant Rectifiers for Variable-Power Operation
14th IEEE Workshop on Control and Modeling for Power Electronics COMPEL '13), June 2013. Design of Resistive-Input Class E Resonant Rectifiers for Variable-Power Operation Juan A. Santiago-González, Khurram
More informationA New Model for Thermal Channel Noise of Deep-Submicron MOSFETS and its Application in RF-CMOS Design
IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 36, NO. 5, MAY 2001 831 A New Model for Thermal Channel Noise of Deep-Submicron MOSFETS and its Application in RF-CMOS Design Gerhard Knoblinger, Member, IEEE,
More informationTHE third-harmonic current injection is a method to reduce
96 IEEE POWER ELECTRONICS LETTERS, VOL. 3, NO. 3, SEPTEMBER 2005 Low-Harmonic, Three-Phase Rectifier That Applies Current Injection and a Passive Resistance Emulator Predrag Pejović, Predrag Božović, and
More informationTHE converter usually employed for single-phase power
82 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 46, NO. 1, FEBRUARY 1999 A New ZVS Semiresonant High Power Factor Rectifier with Reduced Conduction Losses Alexandre Ferrari de Souza, Member, IEEE,
More informationPOWERED electronic equipment with high-frequency inverters
IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS II: EXPRESS BRIEFS, VOL. 53, NO. 2, FEBRUARY 2006 115 A Novel Single-Stage Power-Factor-Correction Circuit With High-Frequency Resonant Energy Tank for DC-Link
More informationA Novel Control Method for Input Output Harmonic Elimination of the PWM Boost Type Rectifier Under Unbalanced Operating Conditions
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 5, SEPTEMBER 2001 603 A Novel Control Method for Input Output Harmonic Elimination of the PWM Boost Type Rectifier Under Unbalanced Operating Conditions
More informationDesign Considerations for 12-V/1.5-V, 50-A Voltage Regulator Modules
776 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 6, NOVEMBER 2001 Design Considerations for 12-V/1.5-V, 50-A Voltage Regulator Modules Yuri Panov and Milan M. Jovanović, Fellow, IEEE Abstract The
More informationA NOVEL SOFT-SWITCHING BUCK CONVERTER WITH COUPLED INDUCTOR
A NOVEL SOFT-SWITCHING BUCK CONVERTER WITH COUPLED INDUCTOR Josna Ann Joseph 1, S.Bella Rose 2 PG Scholar, Karpaga Vinayaga College of Engineering and Technology, Chennai 1 Professor, Karpaga Vinayaga
More informationMODERN switching power converters require many features
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 19, NO. 1, JANUARY 2004 87 A Parallel-Connected Single Phase Power Factor Correction Approach With Improved Efficiency Sangsun Kim, Member, IEEE, and Prasad
More informationResonant Power Conversion
Resonant Power Conversion Prof. Bob Erickson Colorado Power Electronics Center Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder Outline. Introduction to resonant
More informationTHE TWO TRANSFORMER active reset circuits presented
698 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: FUNDAMENTAL THEORY AND APPLICATIONS, VOL. 44, NO. 8, AUGUST 1997 A Family of ZVS-PWM Active-Clamping DC-to-DC Converters: Synthesis, Analysis, Design, and
More informationNOWADAYS, several techniques for high-frequency dc dc
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 54, NO. 5, OCTOBER 2007 2779 Voltage Oscillation Reduction Technique for Phase-Shift Full-Bridge Converter Ki-Bum Park, Student Member, IEEE, Chong-Eun
More informationTHE gyrator is a passive loss-less storage less two-port network
1418 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS II: EXPRESS BRIEFS, VOL. 53, NO. 12, DECEMBER 2006 Gyrator Realization Based on a Capacitive Switched Cell Doron Shmilovitz, Member, IEEE Abstract Efficient
More informationTO LIMIT degradation in power quality caused by nonlinear
1152 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 6, NOVEMBER 1998 Optimal Current Programming in Three-Phase High-Power-Factor Rectifier Based on Two Boost Converters Predrag Pejović, Member,
More informationRECENTLY, newly emerging power-electronics applications
IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 54, NO. 8, AUGUST 2007 1809 Nonisolation Soft-Switching Buck Converter With Tapped-Inductor for Wide-Input Extreme Step-Down Applications
More informationA 7-GHz 1.8-dB NF CMOS Low-Noise Amplifier
852 IEEE JOURNAL OF SOLID-STATE CIRCUITS, VOL. 37, NO. 7, JULY 2002 A 7-GHz 1.8-dB NF CMOS Low-Noise Amplifier Ryuichi Fujimoto, Member, IEEE, Kenji Kojima, and Shoji Otaka Abstract A 7-GHz low-noise amplifier
More informationStep-Up Switching-Mode Converter With High Voltage Gain Using a Switched-Capacitor Circuit
1098 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: FUNDAMENTAL THEORY AND APPLICATIONS, VOL. 50, NO. 8, AUGUST 2003 Step-Up Switching-Mode Converter With High Voltage Gain Using a Switched-Capacitor Circuit
More informationTHE MAGNETIC amplifier (magamp) technique is one of
882 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 5, SEPTEMBER 1999 Small-Signal Modeling of Nonideal Magamp PWM Switch Milan M. Jovanović, Senior Member, IEEE, and Laszlo Huber, Member, IEEE Abstract
More informationHigh efficiency linear
From April 2011 High Frequency Electronics Copyright 2011 Summit Technical Media, LLC An Outphasing Transmitter Using Class-E PAs and Asymmetric Combining: Part 1 By Ramon Beltran, RF Micro Devices; Frederick
More informationDevelopment of a Switched-Capacitor DC DC Converter with Bidirectional Power Flow
IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: FUNDAMENTAL THEORY AND APPLICATIONS, VOL. 47, NO. 9, SEPTEMBER 2000 383 Development of a Switched-Capacitor DC DC Converter with Bidirectional Power Flow Henry
More informationA New Topology of Load Network for Class F RF Power Amplifiers
A New Topology of Load Network for Class F RF Firas Mohammed Ali Al-Raie Electrical Engineering Department, University of Technology/Baghdad. Email: 30204@uotechnology.edu.iq Received on:12/1/2016 & Accepted
More informationComparison of Simulation and Experimental Results of Class - D Inverter Fed Induction Heater
Research Journal of Applied Sciences, Engineering and Technology 2(7): 635-641, 2010 ISSN: 2040-7467 Maxwell Scientific Organization, 2010 Submitted Date: July 01, 2010 Accepted Date: August 26, 2010 Published
More informationIEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 4, JULY
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 4, JULY 2008 1649 Open-Loop Control Methods for Interleaved DCM/CCM Boundary Boost PFC Converters Laszlo Huber, Member, IEEE, Brian T. Irving, and Milan
More informationRealization of Digital Audio Amplifier Using Zero-Voltage-Switched PWM Power Converter
IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: FUNDAMENTAL THEORY AND APPLICATIONS, VOL. 47, NO. 3, MARCH 2000 303 Realization of Digital Audio Amplifier Using Zero-Voltage-Switched PWM Power Converter Wing-Hong
More informationSimulation of Soft Switched Pwm Zvs Full Bridge Converter
Simulation of Soft Switched Pwm Zvs Full Bridge Converter Deepak Kumar Nayak and S.Rama Reddy Abstract This paper deals with the analysis and simulation of soft switched PWM ZVS full bridge DC to DC converter.
More informationGENERALLY speaking, to decrease the size and weight of
532 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 24, NO. 2, FEBRUARY 2009 A Low-Consumption Regulated Gate Driver for Power MOSFET Ren-Huei Tzeng, Student Member, IEEE, and Chern-Lin Chen, Senior Member,
More informationAnalysis and Design of a Current-Mode PWM Buck Converter Adopting the Output-Voltage Independent Second-Order Slope Compensation Scheme
490 IEICE TRANS. FUNDAMENTALS, VOL.E88 A, NO.2 FEBRUARY 2005 PAPER Special Section on Analog Circuit Techniques and Related Topics Analysis and Design of a Current-Mode PWM Buck Converter Adopting the
More informationConventional Single-Switch Forward Converter Design
Maxim > Design Support > Technical Documents > Application Notes > Amplifier and Comparator Circuits > APP 3983 Maxim > Design Support > Technical Documents > Application Notes > Power-Supply Circuits
More informationENERGY saving through efficient equipment is an essential
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 61, NO. 9, SEPTEMBER 2014 4649 Isolated Switch-Mode Current Regulator With Integrated Two Boost LED Drivers Jae-Kuk Kim, Student Member, IEEE, Jae-Bum
More informationA DC DC Boost Converter for Photovoltaic Application
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, Volume 8, Issue 8 (September 2013), PP. 47-52 A DC DC Boost Converter for Photovoltaic Application G.kranthi
More informationCHAPTER 2 A SERIES PARALLEL RESONANT CONVERTER WITH OPEN LOOP CONTROL
14 CHAPTER 2 A SERIES PARALLEL RESONANT CONVERTER WITH OPEN LOOP CONTROL 2.1 INTRODUCTION Power electronics devices have many advantages over the traditional power devices in many aspects such as converting
More informationNOWADAYS, multistage amplifiers are growing in demand
1690 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS I: REGULAR PAPERS, VOL. 51, NO. 9, SEPTEMBER 2004 Advances in Active-Feedback Frequency Compensation With Power Optimization and Transient Improvement Hoi
More informationSIMULATION STUDIES OF HALF-BRIDGE ISOLATED DC/DC BOOST CONVERTER
POZNAN UNIVE RSITY OF TE CHNOLOGY ACADE MIC JOURNALS No 80 Electrical Engineering 2014 Adam KRUPA* SIMULATION STUDIES OF HALF-BRIDGE ISOLATED DC/DC BOOST CONVERTER In order to utilize energy from low voltage
More informationDesign methodology for a very high frequency resonant boost converter
Design methodology for a very high frequency resonant boost converter The MIT Faculty has made this article openly available. Please share how this access benefits you. Your story matters. Citation As
More informationA Color LED Driver Implemented by the Active Clamp Forward Converter
A Color LED Driver Implemented by the Active Clamp Forward Converter C. H. Chang, H. L. Cheng, C. A. Cheng, E. C. Chang * Power Electronics Laboratory, Department of Electrical Engineering I-Shou University,
More informationHybrid Active Power Filters for Reactive Power Compensation with Adaptive DC-Link Voltage Control
International Journal of Scientific Engineering and Research (IJSER) Hybrid Active Power Filters for Reactive Power Compensation with Adaptive DC-Link Voltage Control Rahul Kumar Patel 1, S. Subha 2 Abstract:
More informationPower Electronics for Inductive Power Transfer Systems. George Kkelis, PhD Student (Yr2) 02 Sept 2015
Power Electronics for Inductive Power Transfer Systems George Kkelis, PhD Student (Yr) g.kkelis13@imperial.ac.uk Sept 15 Introduction IPT System Set-Up: TX DC Load Inverter Power Meter ectifier Wireless
More informationANALYSIS OF BROADBAND GAN SWITCH MODE CLASS-E POWER AMPLIFIER
Progress In Electromagnetics Research Letters, Vol. 38, 151 16, 213 ANALYSIS OF BROADBAND GAN SWITCH MODE CLASS-E POWER AMPLIFIER Ahmed Tanany, Ahmed Sayed *, and Georg Boeck Berlin Institute of Technology,
More informationImplementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation
Implementation of Single Stage Three Level Power Factor Correction AC-DC Converter with Phase Shift Modulation Ms.K.Swarnalatha #1, Mrs.R.Dheivanai #2, Mr.S.Sundar #3 #1 EEE Department, PG Scholar, Vivekanandha
More informationImplementation of high-power Bidirectional dc-dc Converter for Aerospace Applications
Implementation of high-power Bidirectional dc-dc Converter for Aerospace Applications Sabarinadh.P 1,Barnabas 2 and Paul glady.j 3 1,2,3 Electrical and Electronics Engineering, Sathyabama University, Jeppiaar
More informationAccurate Modeling of Core-Type Distribution Transformers for Electromagnetic Transient Studies
IEEE TRANSACTIONS ON POWER DELIVERY, VOL. 17, NO. 4, OCTOBER 2002 969 Accurate Modeling of Core-Type Distribution Transformers for Electromagnetic Transient Studies Taku Noda, Member, IEEE, Hiroshi Nakamoto,
More informationCHAPTER 2 AN ANALYSIS OF LC COUPLED SOFT SWITCHING TECHNIQUE FOR IBC OPERATED IN LOWER DUTY CYCLE
40 CHAPTER 2 AN ANALYSIS OF LC COUPLED SOFT SWITCHING TECHNIQUE FOR IBC OPERATED IN LOWER DUTY CYCLE 2.1 INTRODUCTION Interleaving technique in the boost converter effectively reduces the ripple current
More informationSEVERAL static compensators (STATCOM s) based on
1118 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 35, NO. 5, SEPTEMBER/OCTOBER 1999 A New Type of STATCOM Based on Cascading Voltage-Source Inverters with Phase-Shifted Unipolar SPWM Yiqiao Liang,
More informationREFERENCES. [1] P. J. van Wijnen, H. R. Claessen, and E. A. Wolsheimer, A new straightforward
REFERENCES [1] P. J. van Wijnen, H. R. Claessen, and E. A. Wolsheimer, A new straightforward calibration and correction procedure for on-wafer high-frequency S-parameter measurements (45 MHz 18 GHz), in
More informationModeling and Simulation of Paralleled Series-Loaded-Resonant Converter
Second Asia International Conference on Modelling & Simulation Modeling and Simulation of Paralleled Series-Loaded-Resonant Converter Alejandro Polleri (1), Taufik (1), and Makbul Anwari () (1) Electrical
More informationAnalysis and design of Class-E power amplifiers at any duty ratio in frequency domain
Analog Integr Circ Sig Process () 67:49 56 OI.7/s47--9568-3 Analysis and design of Class-E power amplifiers at any duty ratio in frequency domain Tianliang Yang Junrui Liang Chunyu Zhao ayue Chen Received:
More information