UNIVERSITI TUN HUSSEIN ONN MALAYSIA FAKULTI TEKNOLOGI KEJURUTERAAN PERANCANGAN KULIAH LECTURE PLAN MAKLUMAT KURSUS (COURSE INFORMATION)

Transcription

1 UNIVERSITI TUN HUSSEIN ONN MALAYSIA FAKULTI TEKNOLOGI KEJURUTERAAN PERANCANGAN KULIAH LECTURE PLAN MAKLUMAT KURSUS (COURSE INFORMATION) SEMESTER / SESI (SEMESTER / SESSION) : SEMESTER 1/ SESSION KOD KURSUS (COURSE CODE) : BNJ NAMA KURSUS (COURSE TITLE) : LUKISAN KEJURUTERAAN ENGINEERING DRAWING BEBAN AKADEMIK PELAJAR (STUDENT ACADEMIC LOAD) : Kategori Aktiviti (Category of Activities) Pembelajaran bersemuka (Face-to-face learning) Pembelajaran kendiri (Independent study) Pentaksiran rasmi (Formal assessment) Aktiviti Pembelajaran (Learning Activities) Jumlah Jam/ Semester (Total Hours/ Semester) Kuliah (Lecture) 14 Tutorial / Amali (Tutorial / Practical) 42 Aktiviti pembelajaran berpusatkan pelajar lain (Other student centered learning activities) 2 Penyediaan tugasan, projek dan lain-lain (Preparing assignment, project and others) 10 Ulangkaji (Revision) 0 Persediaan bagi pentaksiran (Preparation for assessment) 8 Pentaksiran berterusan (Continuous assessment) 4 Peperiksaan akhir (Final examination) 0 JUMLAH JAM BELAJAR PELAJAR (JBP) (TOTAL STUDENT LEARNING TIME (SLT)) 80 Kursus Pra-syarat (Prerequisite Course) : None Nama Staf Akademik (Name of Academic Staff) : Ashari bin Kasmin (Penyelaras Kursus) Dr. Mohd Hezri bin Mohd Lwi@Mokhtar Haffidzudin bin Hehsan Siti Zaharah Binti Kunchi Mon Dalila binti Mohd Harun Disediakan oleh (Prepared by): Penyelaras Kursus Tandatangan (Signature): Nama (Name): Ashari bin Kasmin Disahkan oleh (Approved by): Ketua Jabatan JTKM Tandatangan (Signature): Nama (Name): Bachik bin Abu Bakar Tarikh (Date): 30 Aug 2015 Tarikh (Date): 30 Aug 2015

2 MATLAMAT (GOALS): The goals of this course is to provide engineering technology student to read and write in engineering graphic language; study on basic theory and draw of engineering equipment components with ordinary routines and mechanical engineering drawing convention. SINOPSIS (SYNOPSIS): This course provides the student with the skill to produce technical drawing using the following drafting skills i.e. manual lettering, technical drafting, basic geometric construction, single and multi-view drawings, scale measurement and the reading of technical drawings through drawings and related assignment. HASIL PEMBELAJARAN (LEARNING OUTCOMES): At the end of this course, the student able to use the knowledge and skills to: (1) Construct plane geometry, orthographic projection view, cross section, and schematic view drawing. (PLO1-C3) (2) Draw the detail drawing, assembly drawing, exploded drawing and bill of materials (BOM). (PLO2-P4) (3) Practice their knowledge in their future career. (PLO6-A2) (4) Analyze and transform the mechanical problem into design in form of technical drawing. (PLO4-C4) ISI KANDUNGAN (CONTENT): MINGGU (WEEK) KANDUNGAN (CONTENT) Introduction (2 Hours) 1.1 Definition of engineering drawing. 1.2 Understand of equipment and material engineering uses method. 1.3 Drawing Standard. 1.4 Lettering and Lines. 1.5 Draw of title box. 1.6 Dimension lines. Plane Geometry (3 Hours) 2.1 Constructing parallel and perpendicular lines from one (1) point. 2.2 Division of lines. 2.3 Constructing angles. 2.4 Constructing circles and an arc through three points. 2.5 Constructing polygons. 2.6 Constructing tangent lines of two circles. 2.7 Constructing similar features. Makmal (Lab) (9 Hours) PENTAKSIRAN (ASSESSMENT) Assignment 1, Test 1, Assignment 2, Test 1,

3 MINGGU (WEEK) KANDUNGAN (CONTENT) Orthographic ion View (2 Hours) 3.1 Principle of orthographic projection. 3.2 Orthographic projection in first-angle and thirdangle projection. 3.3 ion system symbols. 3.4 Selection of views. 3.5 ing of curve, circle and arc surfaces. 3.6 Dimensioning of orthographic views. Ujian 1 (Test 1) - Week 6 - (2 Hours) Schematic View Drawing (2 Hours) 4.1 Characteristics of isometric, oblique and perspective drawing. 4.2 Constructing isometric drawing method. 4.3 Circles and curves in isometric view. 4.4 Dimensioning of isometric drawing. Cross Section View (2 Hours) 5.1 Section concept: Cutting plane, face and lines of section. 5.2 Sectioning symbols. 5.3 Types of section view and application: Full sections, Half sections, Offset sections, Partial sections, Broken-out sections, Revolved sections, Removed sections and special case. PENTAKSIRAN (ASSESSMENT) Assignment 3, Test 2, Assignment 4, Test 2, Assignment 5, Test 2, Detail Mechanical Drawing (1 Hour) 6.1 Understand types of mechanical drawing. 6.2 Ordinary routines and convention in mechanical drawing following ANSI Standard: Hidden lines, Hole details, Alignments, Threads, Movement components, Screws, Bolt and nut, Gears, Surface textures, Dimensions, Tolerances, limits and assemblies and welding. 6.3 Draw a single component for engineering equipments in orthographic projection views. Makmal (Lab) (3 Hours) Ujian 2 (Test 2) (2 Hours)

4 MINGGU (WEEK) KANDUNGAN (CONTENT) Drawing in Industry (1 Hour) 7.1 Detail drawing. 7.2 Assembly drawing 7.3 Exploded drawing 7.4 Bill of Materials (BOM) Makmal (Lab) (3 Hours) PENTAKSIRAN (ASSESSMENT) Presentation & Report Submission TUGASAN / PROJEK (ASSIGNMENT / PROJECT): Individual Assignment - 5 Group - 1 PENTAKSIRAN (ASSESSMENT): 1. Ujian 1 (Test 1) : 20 % C3 / PLO1 2. Ujian 2 (Test 2) : 20 % C3 / PLO1 3. Tugasan (Assignments) : 25 % P4 / PLO2 4. Projek () : Problem solving : 10 % C4 / PLO4 Drawing : 10 % P4 / PLO2 Softskills (Life-long learning) : 15 % A2 / PLO6 RUJUKAN (REFERENCES): Jumlah (Total) : 100 % (50% C, 35% P, 15 % A) 1. Aminudin Abu et. al., (2008), Asas Lukisan Kejuruteraan dan Berbantu Komputer, Selangor: Pearson Malaysia. No. Panggilan T353.A Cecil Jensen, Jay D. Helsel, Dennis R. Short, (2008), Engineering Drawing And Design, Boston: McGraw-Hill. No. Panggilan T353.J Mohd Fadzil Daud, Khairul Anuar Hanafiah, (2005) Panduan Asas Lukisan Kejuruteraan, Edisi Kedua, Universiti Teknologi Malaysia. No. Panggilan T353.M M. B. Shah, B. C. Rana, (2005), Engineering Drawing, New Delhi: Pearson Education. No. Panggil T353.S Gieseckle, Mitchel. Hill (2000), Engineering Graphics, Seventh Edition, Prentice Hall, Prectice Hall. No. Panggilan T467.E

5 KEHADIRAN / PERATURAN SEMASA KULIAH (ATTENDANCE / REGULATIONS DURING LECTURE) 1. Pelajar mesti hadir tidak kurang dari 80% masa pertemuan yang ditentukan bagi sesuatu kursus termasuk kursus Hadir Wajib (HW) dan kursus Hadir Sahaja (HS). Students must attend not less than 80% of the contact hours specified for a course including Compulsory Attendance (HW) course and Attendance Only (HS) course. 2. Pelajar yang tidak memenuhi perkara 1 di atas tidak dibenarkan menghadiri kuliah dan menduduki sebarang bentuk pentaksiran selanjutnya. Markah sifar 0 akan diberikan kepada pelajar yang gagal memenuhi perkara 1. Manakala untuk kursus HW, pelajar yang gagal memenuhi perkara 1 akan diberi gred Hadir Gagal (HG). Students who do not fulfill item 1 of the above are not allowed to attend further lecture and sit for any form of assessment. Zero 0 mark will be given to students who fail to comply with item 1. As for HW course, students who fail to comply with item 1 will be given Failure Attendance (HG) grade. 3. Pelajar perlu patuh kepada peraturan berpakaian yang berkuatkuasa dan menjaga disiplin diri masingmasing untuk mengelakkan dari tindakan tatatertib diambil terhadap pelajar. Students should adhere to the dress regulations in effect and must discipline themselves to avoid from any disciplinary actions. 4. Pelajar perlu mematuhi peraturan keselamatan sepanjang aktiviti pembelajaran dan pengajaran. Students should adhere to the safety regulations throughout the learning and teaching activities. MATRIK HASIL PEMBELAJARAN KURSUS DAN HASIL PEMBELAJARAN PROGRAM (MATRIX OF COURSE LEARNING OUTCOMES AND PROGRAMME LEARNING OUTCOMES) Dilampirkan. (Attached).

6 MATRIK HASIL PEMBELAJARAN KURSUS DAN HASIL PEMBELAJARAN PROGRAM MATRIX OF COURSE LEARNING OUTCOMES AND PROGRAMME LEARNING OUTCOMES Fakulti (Faculty) : Fakulti Teknologi Kejuruteraan Matrik ini perlu digunakan bersama: (This matrix is to be used with) Program (Programme) : BNH, BNK, BNL, BNG, BNM 1. Objektif Pendidikan Program (PEO) (Programme Educational Objectives (PEO)) Kod Kursus (Course Code) : BNJ Hasil Pembelajaran Program (PLO) (Programme Learning Outcomes (PLO)) Nama Kursus (Course Title) : Lukisan Kejuruteraan Bil. (No.) Hasil Pembelajaran Kursus (Course Learning Outcomes) 1. Construct plane geometry, orthographic projection view, cross section, and schematic view drawing. 2. Draw the detail drawing, assembly drawing, exploded drawing and bill of materials (BOM). 3. Practise their knowledge in their future career. 4. Analyze and transform the mechanical problem into design in form of technical drawing. PLO1 C3 PLO2 P4 Pematuhan kepada PLO (Compliance to PLO) PLO3 PLO4 PLO5 PLO6 PLO7 PLO8 PLO9 PLO10 PLO11 A2 C4 PLO12 PLO13 Kaedah Penyampaian (Method of Delivery) Kaedah Pentaksiran (Method of Assessment) Tests Assignments & KPI Jumlah (Total) Taksonomi Pembelajaran (Learning Taxonomy) Kognitif (Cognitive) Psikomotor (Psychomotor) Afektif (Affective) C1 Pengetahuan (Knowledge) P1 Persepsi (Perception) A1 Menerima (Receiving) C2 Pemahaman (Comprehension) P2 Set (Set) A2 Memberikan Maklum Balas (Responding) C3 Aplikasi (Application) P3 Respons Berpandu (Guided Response) A3 Menilai (Valuing) C4 Analisis (Analysis) P4 Mekanisme (Mechanism) A4 Mengorganisasi (Organising) C5 Sintesis (Synthesis) P5 Respons Ketara Kompleks (Complex Overt Response) A5 Menghayati Nilai (Internalising) C6 Penilaian (Evaluation) P6 Adaptasi (Adaptation) P7 Lakuan Tulen (Origination)