Speed and Image Brightness uniformity of telecentric lenses
|
|
- Raymond Cummings
- 5 years ago
- Views:
Transcription
1 Specialist Article Published by: elektronikpraxis.de Issue: 11 / 2013 Speed and Image Brightness uniformity of telecentric lenses Author: Dr.-Ing. Claudia Brückner, Optics Developer, Vision & Control GmbH
2 SPEED AND IMAGE BRIGHTNESS UNIFORMITY OF TELECENTRIC LENSES The correct exposure time depends on the speed of a lens. The level of brightness uniformity determines whether the same processing algorithms can be used for the entire image area. This article describes the behavior of these two properties on telecentric lenses compared to entocentric lenses and also discusses the key parameters. The most efficient solution for a machine vision application is not always obvious. The characteristics of the lens influence the requirements which are placed on the image processing components located behind the lens including the processing software. Simply stated, the exposure time can be shorter if a high-quality lens is used. In addition, there is no need for processing algorithms. This is a crucial factor in high-speed measurement and monitoring applications, for example PCB inspection in electronics manufacturing where cycles times are less than 40 ms, leaving only 10 ms for image acquisition. High-speed lenses are needed to ensure correct exposure and render all of the components visible. If the brightness is uniform over the image area, the limits which have been defined can be applied to the entire image. Program loops are no longer needed to continually define new grayscale thresholds for different areas on the image. Experience has shown that this is a particularly important factor in the long-term stability of an inspection system. To verify conformance to product specifications, telecentric lens play a key role because they provide a nearly complete, undistorted, high-resolution view of the objects. This feature differentiates them from normal photographic lenses. Because those lenses are normally entocentric, object images are subject to a greater or less extent to the perspective effect. On entocentric lenses, the center of perspectivity is located between the object and the lens (Fig. 1). Fig. 1: The extent of the perspective effect is a major distinguishing characteristic for lenses. Because telecentric lenses are not subject to perspective errors, the surface-mounted components on the PCB are also clearly visible. Technical article: Speed and Image Brightness Uniformity of Telecentric Lenses 1
3 Objects which are closer to the lens appear larger than when they are further way. As a result, the rear edges of objects which have significant depth can be hidden behind the front edges or incorrect object dimensions can be derived due to variations in the object-to-lens distance. Telecentric lenses, or to be more exact object-space telecentric lenses, can eliminate the perspective effect along with the associated disadvantages. The center of perspectivity in the image space is at infinity. Through parallel projection, same-size objects appear as such in the image even if the object-to-lens distance varies. The front diameter of the lens must be at least as large as the object. The way the lenses work is based on the position of the aperture stop. Fig. 2: The perspective effect of a lens depends on the position of the aperture stop. The position also determines the beam s angle of incidence on the sensor. Object imaging is not the only task for optical systems used in machine vision applications. Aperture imaging is also performed simultaneously. This determines from what direction and in what amount the rays coming from the object are captured in the image. On image-space telecentric lenses, the entrance pupil is at infinity. This design feature plays a crucial role in image uniformity as explained below. Bi-telecentric lenses combine the advantages of object-space and image-space telecentricity. WORKING F-NUMBER PROVIDES A BASIS FOR COMPARING LENS SPEED Lens speed determines the correct exposure time. The working F-number N w is used to indicate lens speed. It is defined such that at the same f-stop and same object illumination density, a lens with the same transmission properties will produce the same illuminance in the image. This number is based essentially on the solid angle projection of the illuminated surface in the sensor plane. The position of the illuminated surface is determined by the exit pupil (the sensorside image of the aperture stop). The working F-number for an object on the optical axis and small angular aperture can be calculated using the image-side angular aperture of the lens: N w = 1/[2 sin(u')]. Technical article: Speed and Image Brightness Uniformity of Telecentric Lenses 2
4 This means that essentially the image-side angular aperture determines lens speed. A larger number indicates greater light-gathering ability of the lens and hence higher speed. When the ambient medium is air, the sine of this angle is the image-side numerical aperture. The imageside numerical aperture NA' is used to describe the speed of a telecentric lens. That number can then be used to calculate the working F-number N w : = 1/(2 NA'). INDEPENDENT LENS PROPERTY: TELECENTRICITY The lens speed depends on the image-side angular aperture and consequently on the diameter of the aperture stop. It is not directly related to the telecentricity condition. However because the aperture stop influences the resolution and depth of field, it is these two parameters which determine lens speed. If only a small depth of field is needed, the aperture stop can be opened wider, increasing the resolution and lens speed. Lenses with large depth of field tend to have lower speed, so they need a longer exposure time. Because the parameters are not dependent on telecentricity, they can be determined in advance using an entocentric lens. These lenses tend to be cheaper and more readily available than telecentric lenses. This approach provides the assurance that the telecentric lens will meet the needs in practical applications. The following section explains how to compare the speed of an entocentric lens with the speed of a telecentric lens. THE F-STOP SETTING ON AN ENTROCENTRIC LENS PROVIDES A BASIS FOR PRELIMINARY TESTS Entocentric lenses are marked with an F-number to indicate the speed of the lens. In general, f- numbers between 1.0 and 2.8 indicate a relatively high speed lens and f-numbers > 16 indicate a relatively slow speed lens. The f-number marking on an entocentric lens is only valid for objects at infinity. It can be calculated from the ratio of the diameter of the lens aperture to the focal length. This is true because the aperture stop is located close to the lens aperture and correlates with the image-side angular aperture (Fig. 2(a)). That does not work for telecentric lenses because this ratio is not related to the image-side angular aperture. If the object is located at a finite distance from the lens as is the case with machine vision applications, the image-space angular aperture u' is reduced compared to an object at infinity (u' infinity ). To determine the working f-number of an entocentric lens, the lens s magnification must be taken into consideration: N w = N (1+M). Real-world imaging is assumed, so magnification is always greater than 0. Conversely, it is possible to calculate the lens f-stop setting for a given working f-number. Typical values for the image-side numerical aperture of telecentric lenses are in the range. Table 1 shows the corresponding working f-numbers and the required f-stop settings on an entocentric lens for different magnification values. Technical article: Speed and Image Brightness Uniformity of Telecentric Lenses 3
5 NA' k eff k (M = 0.25) k (M = 0.5) k (M = 1) k (M = 2) Table 1: Conversion of numerical aperture NA' to working F-number and determination of the f-stop setting to produce the same brightness in the image on an entocentric lens for different values of magnification M. ANGLE-DEPENDENT: IMAGE BRIGHTNESS UNIFORMITY The relative illuminance on the detector is plotted against the image height to depict the progression of brightness in the image. The illumination falloff or vignetting indicates the maximum intensity decrease in percent. Ideally, maximum brightness is reached on the optical axis. Outside of the optical axis, brightness depends on the angle of incidence of the chief ray on the sensor, in other words at how large an angle the beam of light hits the sensor. This falloff can be described using the 4 th power of the cosine (Fig. 3). Fig. 3: Graph showing brightness as a function of the chief ray angle of incidence Technical article: Speed and Image Brightness Uniformity of Telecentric Lenses 4
6 Illumination falloff occurs because the solid angle projection of the illuminated surface in the sensor plane is reduced as the chief ray angle increases. This reduction in brightness is known as natural vignetting. Artificial vignetting can also cause loss of brightness when light beams coming from objects are partially blocked due to lens limitations. Aberrations can cause distortion of the light beam, resulting in non-uniform illumination. The chief ray angle on object-space only telecentric lenses is typically up to 15. Illumination falloff at the edge of the image is then around 13%. At maximum intensity in the center of the image with a grayscale value of 250, the grayscale value is only 218 at the image edge which is 32 shades of gray lower. The result can be for example that the position of the edge cannot be reliably detected because a specific threshold must be exceeded for localization. Image-space telecentricity can help alleviate natural vignetting. Lenses which have this property are also known as anti-shading lenses. Image-space telecentricity can also be used on entocentric lenses and in combination with object-space telecentric lenses. Due to the position of the aperture stop, the exit pupil is at image-space infinity. As a result, the beams are all in parallel and all strike the sensor without loss of brightness. This type of lens must be at least as large as the sensor on the sensor side plus a bit more to avoid artificial edge shading. The new vicotar T150/0.26K lens from Vision & Control combines the advantages of object-space and image-space telecentricity. Image-space telecentricity limits illumination falloff for an image circle diameter of 10 mm to 2.3% as shown in Fig. 4. Image sensors up to 2/3" can be used fold magnification makes the lens particularly suitable for inspection systems in the semiconductor industry. Fig. 4: For an image circle of 10 mm, illumination falloff is less than 2.3%. Technical article: Speed and Image Brightness Uniformity of Telecentric Lenses 5
7 Telecentric lenses offer a complete, undistorted, high-resolution view of objects, providing the basis for high-precision measurement and reliable inspection. As described above, the speed of these lenses is not related to telecentricity. It can be estimated using the working F-number and compared with the speed of entocentric lenses. Image-space telecentric lenses can produce uniformly illuminated image areas, eliminating the need for program loops in the processing software. Overall, the measurements are more stable and reliable. Author: Dr. Claudia Brückner, Optics Developer, Vision & Control GmbH Appeared in elektronikpraxis.de Technical article: Speed and Image Brightness Uniformity of Telecentric Lenses 6
APPLICATIONS FOR TELECENTRIC LIGHTING
APPLICATIONS FOR TELECENTRIC LIGHTING Telecentric lenses used in combination with telecentric lighting provide the most accurate results for measurement of object shapes and geometries. They make attributes
More informationOpto Engineering S.r.l.
TUTORIAL #1 Telecentric Lenses: basic information and working principles On line dimensional control is one of the most challenging and difficult applications of vision systems. On the other hand, besides
More informationProperties of optical instruments. Visual optical systems part 2: focal visual instruments (microscope type)
Properties of optical instruments Visual optical systems part 2: focal visual instruments (microscope type) Examples of focal visual instruments magnifying glass Eyepieces Measuring microscopes from the
More informationOptoliner NV. Calibration Standard for Sighting & Imaging Devices West San Bernardino Road West Covina, California 91790
Calibration Standard for Sighting & Imaging Devices 2223 West San Bernardino Road West Covina, California 91790 Phone: (626) 962-5181 Fax: (626) 962-5188 www.davidsonoptronics.com sales@davidsonoptronics.com
More informationOptical basics for machine vision systems. Lars Fermum Chief instructor STEMMER IMAGING GmbH
Optical basics for machine vision systems Lars Fermum Chief instructor STEMMER IMAGING GmbH www.stemmer-imaging.de AN INTERNATIONAL CONCEPT STEMMER IMAGING customers in UK Germany France Switzerland Sweden
More informationTangents. The f-stops here. Shedding some light on the f-number. by Marcus R. Hatch and David E. Stoltzmann
Tangents Shedding some light on the f-number The f-stops here by Marcus R. Hatch and David E. Stoltzmann The f-number has peen around for nearly a century now, and it is certainly one of the fundamental
More informationLens Design I. Lecture 3: Properties of optical systems II Herbert Gross. Summer term
Lens Design I Lecture 3: Properties of optical systems II 207-04-20 Herbert Gross Summer term 207 www.iap.uni-jena.de 2 Preliminary Schedule - Lens Design I 207 06.04. Basics 2 3.04. Properties of optical
More informationINFLUENCE OF VARIABLE APERTURE STOP
INFLUENCE OF VARIABLE APERTURE STOP IN TELECENTRIC IMAGING LENSES SILL OPTICS GMBH CO. KG TECHNOLOGY FORUM MACHINE VISION 2015/16 Konrad Hentschel, Dipl-Phys. Andreas Platz, M.Sc. Project Management CONTENT
More informationLens Design I. Lecture 3: Properties of optical systems II Herbert Gross. Summer term
Lens Design I Lecture 3: Properties of optical systems II 205-04-8 Herbert Gross Summer term 206 www.iap.uni-jena.de 2 Preliminary Schedule 04.04. Basics 2.04. Properties of optical systrems I 3 8.04.
More informationLecture 2: Geometrical Optics. Geometrical Approximation. Lenses. Mirrors. Optical Systems. Images and Pupils. Aberrations.
Lecture 2: Geometrical Optics Outline 1 Geometrical Approximation 2 Lenses 3 Mirrors 4 Optical Systems 5 Images and Pupils 6 Aberrations Christoph U. Keller, Leiden Observatory, keller@strw.leidenuniv.nl
More informationLens Design I. Lecture 5: Advanced handling I Herbert Gross. Summer term
Lens Design I Lecture 5: Advanced handling I 2018-05-17 Herbert Gross Summer term 2018 www.iap.uni-jena.de 2 Preliminary Schedule - Lens Design I 2018 1 12.04. Basics 2 19.04. Properties of optical systems
More informationSome of the important topics needed to be addressed in a successful lens design project (R.R. Shannon: The Art and Science of Optical Design)
Lens design Some of the important topics needed to be addressed in a successful lens design project (R.R. Shannon: The Art and Science of Optical Design) Focal length (f) Field angle or field size F/number
More informationChapter 3 Op,cal Instrumenta,on
Imaging by an Op,cal System Change in curvature of wavefronts by a thin lens Chapter 3 Op,cal Instrumenta,on 3-1 Stops, Pupils, and Windows 3-4 The Camera 3-5 Simple Magnifiers and Eyepieces 1. Magnifiers
More informationOptics: An Introduction
It is easy to overlook the contribution that optics make to a system; beyond basic lens parameters such as focal distance, the details can seem confusing. This Tech Tip presents a basic guide to optics
More informationLecture 2: Geometrical Optics. Geometrical Approximation. Lenses. Mirrors. Optical Systems. Images and Pupils. Aberrations.
Lecture 2: Geometrical Optics Outline 1 Geometrical Approximation 2 Lenses 3 Mirrors 4 Optical Systems 5 Images and Pupils 6 Aberrations Christoph U. Keller, Leiden Observatory, keller@strw.leidenuniv.nl
More informationSection 3. Imaging With A Thin Lens
3-1 Section 3 Imaging With A Thin Lens Object at Infinity An object at infinity produces a set of collimated set of rays entering the optical system. Consider the rays from a finite object located on the
More informationLecture 4: Geometrical Optics 2. Optical Systems. Images and Pupils. Rays. Wavefronts. Aberrations. Outline
Lecture 4: Geometrical Optics 2 Outline 1 Optical Systems 2 Images and Pupils 3 Rays 4 Wavefronts 5 Aberrations Christoph U. Keller, Leiden University, keller@strw.leidenuniv.nl Lecture 4: Geometrical
More informationOptical Design with Zemax
Optical Design with Zemax Lecture : Correction II 3--9 Herbert Gross Summer term www.iap.uni-jena.de Correction II Preliminary time schedule 6.. Introduction Introduction, Zemax interface, menues, file
More informationLens Design I Seminar 1
Xiang Lu, Ralf Hambach Friedrich Schiller University Jena Institute of Applied Physics Albert-Einstein-Str 15 07745 Jena Lens Design I Seminar 1 Warm-Up (20min) Setup a single, symmetric, biconvex lens
More informationCh 24. Geometric Optics
text concept Ch 24. Geometric Optics Fig. 24 3 A point source of light P and its image P, in a plane mirror. Angle of incidence =angle of reflection. text. Fig. 24 4 The blue dashed line through object
More informationProperties of optical instruments. Projection optical systems
Properties of optical instruments Projection optical systems Instruments : optical systems designed for a specific function Projection systems: : real image (object real or at infinity) Examples: videoprojector,,
More informationPhys 531 Lecture 9 30 September 2004 Ray Optics II. + 1 s i. = 1 f
Phys 531 Lecture 9 30 September 2004 Ray Optics II Last time, developed idea of ray optics approximation to wave theory Introduced paraxial approximation: rays with θ 1 Will continue to use Started disussing
More informationChapter 3 Op+cal Instrumenta+on
Chapter 3 Op+cal Instrumenta+on 3-1 Stops, Pupils, and Windows 3-4 The Camera 3-5 Simple Magnifiers and Eyepieces 3-6 Microscopes 3-7 Telescopes Today (2011-09-22) 1. Magnifiers 2. Camera 3. Resolution
More informationImaging Optics Fundamentals
Imaging Optics Fundamentals Gregory Hollows Director, Machine Vision Solutions Edmund Optics Why Are We Here? Topics for Discussion Fundamental Parameters of your system Field of View Working Distance
More informationGeometric optics & aberrations
Geometric optics & aberrations Department of Astrophysical Sciences University AST 542 http://www.northerneye.co.uk/ Outline Introduction: Optics in astronomy Basics of geometric optics Paraxial approximation
More informationOptical design of a high resolution vision lens
Optical design of a high resolution vision lens Paul Claassen, optical designer, paul.claassen@sioux.eu Marnix Tas, optical specialist, marnix.tas@sioux.eu Prof L.Beckmann, l.beckmann@hccnet.nl Summary:
More informationTECHSPEC COMPACT FIXED FOCAL LENGTH LENS
Designed for use in machine vision applications, our TECHSPEC Compact Fixed Focal Length Lenses are ideal for use in factory automation, inspection or qualification. These machine vision lenses have been
More informationGuide to SPEX Optical Spectrometer
Guide to SPEX Optical Spectrometer GENERAL DESCRIPTION A spectrometer is a device for analyzing an input light beam into its constituent wavelengths. The SPEX model 1704 spectrometer covers a range from
More informationBreaking Down The Cosine Fourth Power Law
Breaking Down The Cosine Fourth Power Law By Ronian Siew, inopticalsolutions.com Why are the corners of the field of view in the image captured by a camera lens usually darker than the center? For one
More informationPHY385H1F Introductory Optics. Practicals Session 7 Studying for Test 2
PHY385H1F Introductory Optics Practicals Session 7 Studying for Test 2 Entrance Pupil & Exit Pupil A Cooke-triplet consists of three thin lenses in succession, and is often used in cameras. It was patented
More informationCHAPTER 33 ABERRATION CURVES IN LENS DESIGN
CHAPTER 33 ABERRATION CURVES IN LENS DESIGN Donald C. O Shea Georgia Institute of Technology Center for Optical Science and Engineering and School of Physics Atlanta, Georgia Michael E. Harrigan Eastman
More informationTelecentric Imaging Object space telecentricity stop source: edmund optics The 5 classical Seidel Aberrations First order aberrations Spherical Aberration (~r 4 ) Origin: different focal lengths for different
More informationSystem/Prescription Data
System/Prescription Data File : U:\alpi's designs\1.0 Meter\1.0 meter optical design\old Lenses- Design Stuff\LCOGT 1.0meter Telescope Design for UCSB.zmx Title: LCOGT 1.0 Meter Telescope Date : THU NOV
More informationOpti 415/515. Introduction to Optical Systems. Copyright 2009, William P. Kuhn
Opti 415/515 Introduction to Optical Systems 1 Optical Systems Manipulate light to form an image on a detector. Point source microscope Hubble telescope (NASA) 2 Fundamental System Requirements Application
More informationHeads Up and Near Eye Display!
Heads Up and Near Eye Display! What is a virtual image? At its most basic, a virtual image is an image that is projected into space. Typical devices that produce virtual images include corrective eye ware,
More informationChapter 34 Geometric Optics
Chapter 34 Geometric Optics Lecture by Dr. Hebin Li Goals of Chapter 34 To see how plane and curved mirrors form images To learn how lenses form images To understand how a simple image system works Reflection
More informationAberrations of a lens
Aberrations of a lens 1. What are aberrations? A lens made of a uniform glass with spherical surfaces cannot form perfect images. Spherical aberration is a prominent image defect for a point source on
More informationMacro Varon 4.5/85. Key features. Applications. Web and surface inspections
The Macro Varon lens has been designed for high resolution 12k line scan cameras with 3.5 µm pixel pitch. They are optimized for an optical magnification range of.5x to 2.x. CAS-lens technology produces
More informationExam Preparation Guide Geometrical optics (TN3313)
Exam Preparation Guide Geometrical optics (TN3313) Lectures: September - December 2001 Version of 21.12.2001 When preparing for the exam, check on Blackboard for a possible newer version of this guide.
More informationLEICA Summarit-S 70 mm ASPH. f/2.5 / CS
Technical Data. Illustration 1:2 Technical Data Order no. 1155 (CS: 1151) Image angle (diagonal, horizontal, vertical) approx. 42 / 35 / 24, corresponds to approx. 56 focal length in 35 format Optical
More informationApplication Note (A11)
Application Note (A11) Slit and Aperture Selection in Spectroradiometry REVISION: C August 2013 Gooch & Housego 4632 36 th Street, Orlando, FL 32811 Tel: 1 407 422 3171 Fax: 1 407 648 5412 Email: sales@goochandhousego.com
More informationIMAGE SENSOR SOLUTIONS. KAC-96-1/5" Lens Kit. KODAK KAC-96-1/5" Lens Kit. for use with the KODAK CMOS Image Sensors. November 2004 Revision 2
KODAK for use with the KODAK CMOS Image Sensors November 2004 Revision 2 1.1 Introduction Choosing the right lens is a critical aspect of designing an imaging system. Typically the trade off between image
More informationThe Bellows Extension Exposure Factor: Including Useful Reference Charts for use in the Field
The Bellows Extension Exposure Factor: Including Useful Reference Charts for use in the Field Robert B. Hallock hallock@physics.umass.edu revised May 23, 2005 Abstract: The need for a bellows correction
More informationLecture Outline Chapter 27. Physics, 4 th Edition James S. Walker. Copyright 2010 Pearson Education, Inc.
Lecture Outline Chapter 27 Physics, 4 th Edition James S. Walker Chapter 27 Optical Instruments Units of Chapter 27 The Human Eye and the Camera Lenses in Combination and Corrective Optics The Magnifying
More informationOptical Design with Zemax for PhD
Optical Design with Zemax for PhD Lecture 7: Optimization II 26--2 Herbert Gross Winter term 25 www.iap.uni-jena.de 2 Preliminary Schedule No Date Subject Detailed content.. Introduction 2 2.2. Basic Zemax
More informationAperture and Digi scoping. Thoughts on the value of the aperture of a scope digital camera combination.
Aperture and Digi scoping. Thoughts on the value of the aperture of a scope digital camera combination. Before entering the heart of the matter, let s do a few reminders. 1. Entrance pupil. It is the image
More informationLens Design I. Lecture 5: Advanced handling I Herbert Gross. Summer term
Lens Design I Lecture 5: Advanced handling I 2015-05-11 Herbert Gross Summer term 2015 www.iap.uni-jena.de 2 Preliminary Schedule 1 13.04. Basics 2 20.04. Properties of optical systrems I 3 27.05. Properties
More informationNew foveated wide angle lens with high resolving power and without brightness loss in the periphery
New foveated wide angle lens with high resolving power and without brightness loss in the periphery K. Wakamiya *a, T. Senga a, K. Isagi a, N. Yamamura a, Y. Ushio a and N. Kita b a Nikon Corp., 6-3,Nishi-ohi
More informationXenon-Zirconia 3.3/92
This lens with.2x magnification is optimized for the use with 12k (62.5 mm) line scan sensors with 5 µm pixel, but can also be used with 16k (82 mm) lines. It is broadband coated and can be used in the
More informationTelecentric lenses.
Telecentric lenses 2014 Bi-Telecentric lenses Titolo Index Descrizione Telecentric lenses Opto Engineering Telecentric lenses represent our core business: these products benefit from a decade-long effort
More informationOptical Components - Scanning Lenses
Optical Components Scanning Lenses Scanning Lenses (Ftheta) Product Information Figure 1: Scanning Lenses A scanning (Ftheta) lens supplies an image in accordance with the socalled Ftheta condition (y
More informationOPTICAL SYSTEMS OBJECTIVES
101 L7 OPTICAL SYSTEMS OBJECTIVES Aims Your aim here should be to acquire a working knowledge of the basic components of optical systems and understand their purpose, function and limitations in terms
More informationSection 11. Vignetting
Copright 2018 John E. Greivenkamp 11-1 Section 11 Vignetting Vignetting The stop determines the sie of the bundle of ras that propagates through the sstem for an on-axis object. As the object height increases,
More informationTopic 6 - Optics Depth of Field and Circle Of Confusion
Topic 6 - Optics Depth of Field and Circle Of Confusion Learning Outcomes In this lesson, we will learn all about depth of field and a concept known as the Circle of Confusion. By the end of this lesson,
More informationECEN 4606, UNDERGRADUATE OPTICS LAB
ECEN 4606, UNDERGRADUATE OPTICS LAB Lab 2: Imaging 1 the Telescope Original Version: Prof. McLeod SUMMARY: In this lab you will become familiar with the use of one or more lenses to create images of distant
More informationPerformance Factors. Technical Assistance. Fundamental Optics
Performance Factors After paraxial formulas have been used to select values for component focal length(s) and diameter(s), the final step is to select actual lenses. As in any engineering problem, this
More informationNikon 200mm f/4d ED-IF AF Micro Nikkor (Tested)
Nikon 200mm f/4d ED-IF AF Micro Nikkor (Tested) Nikon 200mm f/4d ED-IF AF Micro Nikkor Image Circle 35mm Type Telephoto Prime Macro Focal Length 200mm APS Equivalent 300mm Max Aperture f/4 Min Aperture
More informationptical Short Course International
ptical Short Course International 6679 N. Calle de Calipso, Tucson, AZ www.oscintl.com 520-797-9744 What s Inside The Box? Optics of Digital Projectors Weekly Newsletter Sponsored By: The Brand for highest
More informationVC 14/15 TP2 Image Formation
VC 14/15 TP2 Image Formation Mestrado em Ciência de Computadores Mestrado Integrado em Engenharia de Redes e Sistemas Informáticos Miguel Tavares Coimbra Outline Computer Vision? The Human Visual System
More informationUsing molded chalcogenide glass technology to reduce cost in a compact wide-angle thermal imaging lens
Using molded chalcogenide glass technology to reduce cost in a compact wide-angle thermal imaging lens George Curatu a, Brent Binkley a, David Tinch a, and Costin Curatu b a LightPath Technologies, 2603
More informationVariable microinspection system. system125
Variable microinspection system system125 Variable micro-inspection system Characteristics Large fields, high NA The variable microinspection system mag.x system125 stands out from conventional LD inspection
More informationActually, you only need to design one monocular of the binocular.
orro rism Binoculars Design a pair of 8X40 binoculars: Actually, you only need to design one monocular of the binocular. Specifications: Objective ocal Length = 200 mm Eye Relief = 15 mm The system stop
More informationOptical System Design
Phys 531 Lecture 12 14 October 2004 Optical System Design Last time: Surveyed examples of optical systems Today, discuss system design Lens design = course of its own (not taught by me!) Try to give some
More informationOptical Design with Zemax
Optical Design with Zemax Lecture 9: Advanced handling 2014-06-13 Herbert Gross Sommer term 2014 www.iap.uni-jena.de 2 Preliminary Schedule 1 11.04. Introduction 2 25.04. Properties of optical systems
More informationOptical Design with Zemax for PhD - Basics
Optical Design with Zemax for PhD - Basics Lecture 3: Properties of optical sstems II 2013-05-30 Herbert Gross Summer term 2013 www.iap.uni-jena.de 2 Preliminar Schedule No Date Subject Detailed content
More informationPoint Spread Function. Confocal Laser Scanning Microscopy. Confocal Aperture. Optical aberrations. Alternative Scanning Microscopy
Bi177 Lecture 5 Adding the Third Dimension Wide-field Imaging Point Spread Function Deconvolution Confocal Laser Scanning Microscopy Confocal Aperture Optical aberrations Alternative Scanning Microscopy
More informationLecture 8. Lecture 8. r 1
Lecture 8 Achromat Design Design starts with desired Next choose your glass materials, i.e. Find P D P D, then get f D P D K K Choose radii (still some freedom left in choice of radii for minimization
More informationLIGHT REFLECTION AND REFRACTION
LIGHT REFLECTION AND REFRACTION REFLECTION OF LIGHT A highly polished surface, such as a mirror, reflects most of the light falling on it. Laws of Reflection: (i) The angle of incidence is equal to the
More informationBasler Accessories. Technical Specification BASLER LENS C M. Order Number
Basler Accessories Technical Specification BASLER LENS C23-1616-2M Order Number 2200000180 Document Number: DG001913 Version: 01 Language: 000 (English) Release Date: 17 January 2018 Contacting Basler
More informationBasler Accessories. Technical Specification BASLER LENS C M. Order Number
Basler Accessories Technical Specification BASLER LENS C23-526-2M Order Number 22183 Document Number: DG1916 Version: 1 Language: (English) Release Date: 17 January 218 Contacting Basler Support Worldwide
More informationBROADCAST ENGINEERING 5/05 WHITE PAPER TUTORIAL. HEADLINE: HDTV Lens Design: Management of Light Transmission
BROADCAST ENGINEERING 5/05 WHITE PAPER TUTORIAL HEADLINE: HDTV Lens Design: Management of Light Transmission By Larry Thorpe and Gordon Tubbs Broadcast engineers have a comfortable familiarity with electronic
More informationOPTICAL IMAGING AND ABERRATIONS
OPTICAL IMAGING AND ABERRATIONS PARTI RAY GEOMETRICAL OPTICS VIRENDRA N. MAHAJAN THE AEROSPACE CORPORATION AND THE UNIVERSITY OF SOUTHERN CALIFORNIA SPIE O P T I C A L E N G I N E E R I N G P R E S S A
More informationChapter 25 Optical Instruments
Chapter 25 Optical Instruments Units of Chapter 25 Cameras, Film, and Digital The Human Eye; Corrective Lenses Magnifying Glass Telescopes Compound Microscope Aberrations of Lenses and Mirrors Limits of
More informationMML-High Resolution 5M Series
Fixed Magnification Series -High Resolution 5M Series High-resolution models that possess the best contrast and NA of all Series. Image acquisition with even higher image quality is realized by combining
More informationLight: Reflection and Refraction Light Reflection of Light by Plane Mirror Reflection of Light by Spherical Mirror Formation of Image by Mirror Sign Convention & Mirror Formula Refraction of light Through
More informationChapter 25. Optical Instruments
Chapter 25 Optical Instruments Optical Instruments Analysis generally involves the laws of reflection and refraction Analysis uses the procedures of geometric optics To explain certain phenomena, the wave
More informationStarBright XLT Optical Coatings
StarBright XLT Optical Coatings StarBright XLT is Celestron s revolutionary optical coating system that outperforms any other coating in the commercial telescope market. Our most popular Schmidt-Cassegrain
More informationUsing Optics to Optimize Your Machine Vision Application
Expert Guide Using Optics to Optimize Your Machine Vision Application Introduction The lens is responsible for creating sufficient image quality to enable the vision system to extract the desired information
More informationDesign Description Document
UNIVERSITY OF ROCHESTER Design Description Document Flat Output Backlit Strobe Dare Bodington, Changchen Chen, Nick Cirucci Customer: Engineers: Advisor committee: Sydor Instruments Dare Bodington, Changchen
More informationPhysics 1230 Homework 8 Due Friday June 24, 2016
At this point, you know lots about mirrors and lenses and can predict how they interact with light from objects to form images for observers. In the next part of the course, we consider applications of
More informationINTRODUCTION TO CCD IMAGING
ASTR 1030 Astronomy Lab 85 Intro to CCD Imaging INTRODUCTION TO CCD IMAGING SYNOPSIS: In this lab we will learn about some of the advantages of CCD cameras for use in astronomy and how to process an image.
More informationFor high resolution, large-sized line sensor cameras. Recommendable line sensor cameras - 5.2μm x 12K / 7μm x 8K
Nikon Rayfact Series Features For high resolution, large-sized line sensor cameras. Recommendable line sensor cameras - 5.2μm x 12K / 7μm x 8K Guarantee high resolution and uniformity from the center to
More informationOption G 2: Lenses. The diagram below shows the image of a square grid as produced by a lens that does not cause spherical aberration.
Name: Date: Option G 2: Lenses 1. This question is about spherical aberration. The diagram below shows the image of a square grid as produced by a lens that does not cause spherical aberration. In the
More informationVC 16/17 TP2 Image Formation
VC 16/17 TP2 Image Formation Mestrado em Ciência de Computadores Mestrado Integrado em Engenharia de Redes e Sistemas Informáticos Hélder Filipe Pinto de Oliveira Outline Computer Vision? The Human Visual
More informationApplications of Optics
Nicholas J. Giordano www.cengage.com/physics/giordano Chapter 26 Applications of Optics Marilyn Akins, PhD Broome Community College Applications of Optics Many devices are based on the principles of optics
More informationChapter 29/30. Wave Fronts and Rays. Refraction of Sound. Dispersion in a Prism. Index of Refraction. Refraction and Lenses
Chapter 29/30 Refraction and Lenses Refraction Refraction the bending of waves as they pass from one medium into another. Caused by a change in the average speed of light. Analogy A car that drives off
More informationDesign and Correction of optical Systems
Design and Correction of optical Sstems Part 5: Properties of Optical Sstems Summer term 2012 Herbert Gross Overview 2 1. Basics 2012-04-18 2. Materials 2012-04-25 3. Components 2012-05-02 4. Paraxial
More informationLaboratory 7: Properties of Lenses and Mirrors
Laboratory 7: Properties of Lenses and Mirrors Converging and Diverging Lens Focal Lengths: A converging lens is thicker at the center than at the periphery and light from an object at infinity passes
More informationLENSES. INEL 6088 Computer Vision
LENSES INEL 6088 Computer Vision Digital camera A digital camera replaces film with a sensor array Each cell in the array is a Charge Coupled Device light-sensitive diode that converts photons to electrons
More informationLens Design I. Lecture 10: Optimization II Herbert Gross. Summer term
Lens Design I Lecture : Optimization II 5-6- Herbert Gross Summer term 5 www.iap.uni-jena.de Preliminary Schedule 3.. Basics.. Properties of optical systrems I 3 7.5..5. Properties of optical systrems
More informationImaging Instruments (part I)
Imaging Instruments (part I) Principal Planes and Focal Lengths (Effective, Back, Front) Multi-element systems Pupils & Windows; Apertures & Stops the Numerical Aperture and f/# Single-Lens Camera Human
More informationParallel Mode Confocal System for Wafer Bump Inspection
Parallel Mode Confocal System for Wafer Bump Inspection ECEN5616 Class Project 1 Gao Wenliang wen-liang_gao@agilent.com 1. Introduction In this paper, A parallel-mode High-speed Line-scanning confocal
More informationORIFICE MEASUREMENT VERISENS APPLICATION DESCRIPTION: REQUIREMENTS APPLICATION CONSIDERATIONS RESOLUTION/ MEASUREMENT ACCURACY. Vision Technologies
VERISENS APPLICATION DESCRIPTION: ORIFICE MEASUREMENT REQUIREMENTS A major manufacturer of plastic orifices needs to verify that the orifice is within the correct measurement band. Parts are presented
More informationSystems Biology. Optical Train, Köhler Illumination
McGill University Life Sciences Complex Imaging Facility Systems Biology Microscopy Workshop Tuesday December 7 th, 2010 Simple Lenses, Transmitted Light Optical Train, Köhler Illumination What Does a
More informationTutorial Zemax 8: Correction II
Tutorial Zemax 8: Correction II 2012-10-11 8 Correction II 1 8.1 High-NA Collimator... 1 8.2 Zoom-System... 6 8.3 New Achromate and wide field system... 11 8 Correction II 8.1 High-NA Collimator An achromatic
More informationSolution of Exercises Lecture Optical design with Zemax for PhD Part 8
2013-06-17 Prof. Herbert Gross Friedrich Schiller University Jena Institute of Applied Physics Albert-Einstein-Str 15 07745 Jena Solution of Exercises Lecture Optical design with Zemax for PhD Part 8 8.1
More informationIMAGE FORMATION. Light source properties. Sensor characteristics Surface. Surface reflectance properties. Optics
IMAGE FORMATION Light source properties Sensor characteristics Surface Exposure shape Optics Surface reflectance properties ANALOG IMAGES An image can be understood as a 2D light intensity function f(x,y)
More informationComputer exercise 2 geometrical optics and the telescope
Computer exercise 2 geometrical optics and the telescope In this exercise, you will learn more of the tools included in Synopsys, including how to find system specifications such as focal length and F-number.
More informationSmart vision and optical solutions for the food and beverage industry
November 2016 Smart vision and optical solutions for the food and beverage industry M. Castelletti Product Manager Table of contents 1 Who we are 2 Smart vision system for food inspection & application
More informationExercises Advanced Optical Design Part 5 Solutions
2014-12-09 Manuel Tessmer M.Tessmer@uni-jena.dee Minyi Zhong minyi.zhong@uni-jena.de Herbert Gross herbert.gross@uni-jena.de Friedrich Schiller University Jena Institute of Applied Physics Albert-Einstein-Str.
More information