architectural Sun control
|
|
- Jasper Carr
- 6 years ago
- Views:
Transcription
1 architectural Sun control
2 natural comfort inside non-residential housing. And that with a minimum of energy consumption. Because Duco s solutions are natural and energy efficient. They give homes and non-domestic buildings an aesthetic added value. The result: Natural Comfort Inside. An optimal indoor climate is healthy and gives a good feeling. Duco developed its Green Building Solution for this reason where basic ventilation, intensive ventilation and solar shading are combined. This enables us to guarantee an optimum air quality and thermal comfort, for both residential and
3 > Table of contents Architectural Sun Control 4 7 Products DucoSun 100 C 8 9 DucoSun 100 C underslung 10 DucoSun 100 C overslung 11 DucoSun 100 C intermediate 12 DucoSun 100 C framed 13 DucoSun 100 C vertical 14 DucoSun 150 CF DucoSun 150 CF underslung 18 DucoSun 150 CF overslung 19 DucoSun 150 CF vertical 20 DucoSun 100 D 150 D DucoSun 100 D/150 D underslung 24 DucoSun 100 D/150 D overslung 25 DucoSun 100 D intermediate 26 DucoSun 100 D framed 27 DucoSun 100 D/150 D vertical 28 DucoSun Ellips DucoSun Ellips intermediate 32 DucoSun Ellips Multifit 33 DucoSun Ellips Unifit 34 DucoSun Ellips moveable 35 DucoSun Cubic DucoSun Cubic intermediate 38 DucoSun Cubic Unifit 39 DucoSun Cubic moveable 40 DucoSun Linear DucoSun Linear intermediate 44 DucoSun Linear Unifit 45 DucoSun Linear moveable 46 Table of contents 3
4 Receive the most sunlight and the least heat. > Night Cooling > fresh air supply > warm air discharge Architectural Sun Control: Aesthetic as well as Functional Typically, solar shading is not always considered from the outset as part of the initial construction plan. This is unwise, as it is an excellent investment with rapid payback potential. The solutions offered by Duco are designed to fit perfectly into design and budget. Duco s external solar shading systems reduce the thermal heat gain in a building in a natural and energy efficient way. They let in the most sunlight and keep the heat from the sun out, whilst providing glare protection and withstanding colour-altering glare. They provide privacy screening for glass façades without obstructing the view from inside to designed to be very much part of a building s aesthetic. Discover Duco s architectural solar shading. When combined with Night Cooling : The alternative to Air Conditioning! For cooling an area, three times as much energy is required than for heating it. Combining an external solar shading system during the day with night-time cooling (aka night cooling) where as much cool fresh air as possible is allowed in and stored during the night is the perfect way to keep the indoor climate pleasant and healthy. The combination of Duco s ventilation and solar shading systems achieves a healthy and energy friendly end result. the exterior. Duco solar shading devices are > clean-cut design > sunlight in, heat gain out > fixed or adjustable > natural comfort > Colour All the types of solar shading systems mentioned in this brochure can be manufactured in any standard RAL colour and in SAA. Special colours are available on request. 4
5 Very wide range of options The Duco s solar shading systems available cover a wide range of options. Systems are available with fixed blades or adjustable blades, with discrete or eye-catching designs and may be used in vertical or horizontal form. Which solar shading you choose, depends on the budget available, the technical options and, of course, on what you like. Whatever system you may choose : Duco ensures an optimum balance between minimum solar heat gain and maximum daylight entry, without solar glare or any resulting colour changes. > Series 1. DucoSun C DucoSun CF - DucoSun D External solar shading systems which have their aluminium solar shading blades clipped onto plastic blade holders. The blade holders are pre-fitted to the aluminium support profile and held in place with the patented Duco turn and click system. A choice of three different blade types is available: C, CF or D. Materials > Aluminium: EN AW 6063 T66 > Surface treatment: Standard natural anodised finish (15-20 µm) (VB6/A20/VOM1) Stove enamelled and polyester powder coated (60-80µm) > Synthetic parts: Polyamide, glass fibre reinforced, UV-resistant 2. DucoSun Ellips - DucoSun Cubic - DucoSun Linear External solar shading systems with either fixed or moveable aluminium solar shading blades fitted to the support system. The austere lines of the solar shading blades improve the aesthetic appeal. A choice of three different blade types is available : Ellips, Cubic, Linear. Materials > Aluminium: EN AW 6060 T66 > Surface treatment: Standard natural anodised finish (15-20 µm) (VB6/A20/VOM1) Stove enamelled and polyester powder coated (60-80µm) architectural sun control 5
6 > Installation Options Horizontal installation Horizontal solar shading systems minimise the solar heat gain during the warmer periods of the year (May-September) but maximise solar gain in the colder months of the year with low level sun angles (October- April). This ensures optimum energy performance. > Strength testing Vertical installation Vertical solar shading systems provide maximum privacy but at the same time allowing a view to the outside. Vertical solar shading systems offer room darkening capabilities. The strength of external solar shading systems is best assessed through wind tunnel testing with air streams up to 800 Pa. Duco has its solar shading systems tested at the von Karman Institute in Brussels, an international leading-edge and independent institute for high technology research in fluid dynamics. All DucoSun systems presented in this product brief have been tested in the laboratories of Duco and at the von Karman Institute. To this effect, Duco has developed a program for strength calculations. 800 Pa DucoSun Ellips, DucoSun Cubic and DucoSun Linear Series solar shading blades for vertical applications can be installed either vertically or horizontally. 6
7 SERVICE PLEASE Duco s R&D department is constantly developing and testing new solutions using the latest cutting-edge technologies. Duco cooperates with well-known institutes including the Belgian WTCB-BBRI-CSTC Institute, the Von Karman Institute, Our expertise supported by many years of experience allows us to develop and deliver the best solutions possible for each of your projects. Duco s project team will be delighted to help you make the responsible choice in the selection of the correct solar shading system for your specific projects. To this end, the team uses proprietary software, among other things, to perform all the required calculations, including strength calculation, calculation of the correct spans and of the sub-structure fixing options. The ideal shadow angles are calculated as well. Here, consideration is also given to façade orientation, the path of the sun, > > Professional intersection planes and fitting drawings. > Specification service : specification text for each type of solar shading device. > Fitting and installation instructions on request. > Certificates > All Duco solar shading systems are guaranteed for 10 years. > Test reports and certificates are available on request. > Completed projects WE INSPIRE AT WWW. DUCO.EU architectural sun control 7
8 DucoSun 100 C DucoSun 100 C Series solar shading devices are architectural component systems featuring fixed C blades. The patented Duco Slide and click system enables quick and straightforward fitting of the solar shading blades to the support system at fixed blade angles. > Straightforward component system > Solid G 30Z > Solar shading blades with discrete C-shaped design. > Quick to install using the patented slide and click system. > Fitting applications specific to any structural technical situation. > Slide and click system Slide Slide Click 8
9 Basic components > Solar shading blades Ø 5,9 100 C Series solar shading blade Optional: 100 C blade, perforated > Blade holders DucoSun C&D blade holder, underslung DucoSun C&D blade holder, vertical/ overslung DucoSun C&D blade holder, framed/ intermediate > Support profiles 30/50 Series support profile 30/50B Series support profile 30/78 Series support profile 30/12 Series support profile 50/12 Series support profile 86/95 Series support profile > Fascia profiles 90 Series fascia profile, full bullnose 100 Series fascia profile, semi-bullnose 175 Series fascia profile, flat 150 Series fascia profile, flat > Frame profiles 100 Series frame profile, flat 100 Series frame profile, full bullnose ducosun 100c 9
10 DucoSun 100 C underslung Permanent external solar shading system. 100 C Series solar shading systems have their aluminium blades below the support profiles at a fixed 60 degree blade mounting angle. All fascia profiles are available in a wide range of finishes. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 C underslung Technical Specifications - Blade: 100 C - Blade holder: underslung (single, connecting and corner holder) - Blade pitch: 100 mm - Blade mounting angle: 60 - Maximum span: 1524 mm - Finish: With plastic stop With fascia profile - Installation: With standard wall bracket With strut and wall anchor On a 30/50, 30/50B or 30/78 Series support profile 150 Series flat, 175 Series flat or 90 Series full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles 10
11 DucoSun 100 C overslung Permanent external solar shading system. 100 C Series solar shading systems have their aluminium blades above the support profiles at a fixed 45 degree blade mounting angle. All fascia profiles are available in a wide range of finishes. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 C overslung Technical Specifications - Blade: 100 C - Blade holder: vertical/overslung (single, connecting and corner holder) - Blade pitch: 107,5 mm - Blade mounting angle: 45SDgr - Maximum span: 1524 mm - Finish: With plastic stop With fascia profile - Installation: With standard wall bracket With strut and wall anchor On a 30/50, 30/50B or 30/78 Series support profile 150 Series flat, 175 Series flat or 90 Series full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles ducosun 100 c underslung - overslung 11
12 DucoSun 100 C intermediate Permanent external solar shading system. 100 C Series solar shading systems have their aluminium blades in between the support profiles at a fixed 45 degree blade mounting angle. A fascia profile is used to provide the finish. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 C intermediate Technical Specifications - Blade: 100 C - Blade holder: framed/intermediate (single and corner holder) - Blade pitch: 107,5 mm - Blade mounting angle: 45 - Maximum span 1524 mm - Finish: With fascia profile - Installation: With standard wall bracket With strut and standard wall anchor 100 Series, semi-bullnose For 86/95 Series support profiles For 86/95 Series support profiles - Auxiliary holders : 50/12 Series support profile 12
13 DucoSun 100 C framed Permanent external solar shading system. 100 C Series solar shading systems have their aluminium blades contained in a frame at a fixed 45 degree blade mounting angle. The frame is finished using a flat or a full bullnose fascia. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 C, framed Technical Specifications - Blade: 100 C - Blade holder: framed/intermediate (single and corner holder) - Blade pitch: 107,5 mm - Blade mounting angle: 45 -Maximum span - Finish: With frame profile - Installation: With standard wall bracket With strut and standard wall anchor 1524 mm 100 Series full bullnose or 100 Series flat For flat 100 Series frame profiles For flat 100 Series frame profiles - Auxiliary holders : 30/12 Series support profile for rectangular frames 50/12 Series support profile for corner frames ducosun 100 c intermediate - framed 13
14 DucoSun 100 C vertical Permanent external solar shading system. 100 C Series solar shading systems have their aluminium blades fitted against the support profiles at a fixed 45 degree blade mounting angle. Technical Specifications > DucoSun 100 C vertical - Blade: 100 C - Blade holder: vertical/overslung (single, connecting and corner holder) - Blade pitch: 127,5 mm - Blade mounting angle: 45 - Maximum span 1524 mm - Installation: With standard support profiles 30/50, 30/78 or 50/12 14
15 15 completed project
16 DucoSun 150 CF DucoSun 150 CF is an architectural component system featuring fixed solar shading blades. The patented Duco Slide and click system enables quick and straightforward fitting of the solar shading blades to the support system at fixed blade angles. 150 CF Series solar shading blades combine the functional advantages of the 100 C Series basic blade with the appealing ellipsoid design of the DucoSun Ellips blade. The blades are extremely strong. That s why much larger spans can be covered with fewer support profiles. > Straightforward component system > Solar shading blades featuring an appealing ellipsoid design. > Quick to install using the patented slide and click system. > The rigidity of the CF Series blades allows large spans. > Large blade pitch (centre-to-centre distance between 2 blades). > Slide and click system Slide Slide Click 16
17 Basic components > Solar shading blades CF Series solar shading blade > Blade holders DucoSun C&D blade holder, underslung DucoSun C&D blade holder, vertical/overslung > Support profiles 30/50 Series support profile 30/50B Series support profile 30/78 Series support profile 50/12 Series support profile > Fascia profiles 90 Series fascia profile, full bullnose ducosun 150 cf 17
18 DucoSun 150 CF underslung Permanent external solar shading system. 150 CF Series solar shading systems have their aluminium blades below the support profiles at a fixed 60 degree blade mounting angle. A fascia profile can be used to provide the finish. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 150 CF underslung Technical Specifications - Blade: 150 CF - Blade end plate Plastic stop for 150 CF Series blades - Blade holder: underslung (single, connecting and corner holder) - Blade pitch: 140 mm - Blade mounting angle: 60 - Maximum span: 2552 mm - Blade holder spacer - Finish: With plastic stop With fascia profile - Installation: With standard wall bracket With strut and wall anchor For fitting blades pitched at 40 mm On a 30/50, 30/50B or 30/78 Series support profile 90 Series, full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles 18
19 DucoSun 150 CF overslung Permanent external solar shading system. 150 CF Series solar shading systems have their aluminium blades above the support profiles at a fixed 45 degree blade mounting angle. A fascia profile can be used to provide the finish. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 150 CF overslung Technical Specifications - Blade: 150 CF - Blade end plate: Plastic stop for 150 CF Series blades - Blade holder: vertical/overslung (single, connecting and corner holder) - Blade pitch: 165 mm - Blade mounting angle: 45 - Maximum span: 2552 mm - Blade holder spacer - Finish: With plastic stop With fascia profile - Installation: With standard wall bracket With strut and wall anchor For fitting blades pitched at 140 mm On a 30/50, 30/50B or 30/78 Series support profile 90 Series, full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles ducosun 150 c underslung - overslung 19
20 DucoSun 150 CF vertical Permanent external solar shading system. 150 CF Series solar shading systems have their aluminium blades fitted against the support profiles at a fixed 45 degree blade mounting angle. Technical Specifications > DucoSun 150 CF vertical - Blade: 150 C - Blade end plate: Plastic stop for 150 CF Series blades - Blade holder: vertical/overslung (single, connecting and corner holder) - Blade pitch: 190 mm - Blade mounting angle: 45 - Maximum span: 2552 mm - Installation: With standard support profiles 30/50, 30/78 or 50/12 20
21 21 completed project
22 DucoSun 100 D/150 D DucoSun 100 D and DucoSun 150 D are both architectural component systems featuring fixed solar shading blades. The patented Duco slide and click system enables quick and straightforward fitting of the solar shading blades to the support system at fixed blade angles. 100 D and 150 D Series solar shading blades combine the functional advantages of the 100 C Series basic blade with an appealing bullnose design. The blades are extremely strong. That s why much larger spans can be covered with fewer support profiles. > Straightforward component system > Solar shading blades featuring an appealing bullnose design. > Quick to install using the patented slide and click system. > The rigidity of the D shaped solar shading blades allows large spans. > The blades can be finished with end plates. > Slide and click system Slide Slide Click Click 22
23 Basic components > Solar shading blades D Series solar shading blade 150 D Series solar shading blade > Blade holders DucoSun C&D blade holder, underslung DucoSun C&D blade holder, vertical/overslung DucoSun C&D blade holder, framed/intermediate > Support profiles 30/50 Series support profile 30/50B Series support profile 30/78 Series support profile 30/12 Series support profile 50/12 Series support profile 86/95 Series support profile > Fascia profiles 90 Series fascia profile, full bullnose > Frame profiles 100 Series frame profile, flat 100 Series fascia profile, semi-bullnose 175 Series fascia profile, flat 100 Series frame profile, full bullnose 150 Series fascia profile, flat ducosun 100 d - ducosun 150 d 23
24 DucoSun 100 D/150 D underslung Permanent external solar shading system. 100 D or 150 D Series solar shading systems have their aluminium blades below the support profiles at a fixed 45 degree blade mounting angle. All fascia profiles are available in a wide range of finishes. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 D underslung > DucoSun 150 D underslung Technical Specifications 100 D 150 D - Blade: 100 D 150 D - Blade end plate Aluminium end plate for 100 D Series blades Aluminium end plate for 150 D Series blades - Blade holder: underslung (single, connecting and corner holder) underslung (single, connecting and corner holder) - Blade pitch: 100 mm 140 mm - Blade mounting angle: Maximum span: 2274 mm 2645 mm - Blade holder spacer N/a For fitting blades pitched at 140 mm - Finish: With plastic stop With fascia profile - Installation: With standard wall bracket With strut and wall anchor On a 30/50, 30/50B or 30/78 Series support profile 150 Series flat, 175 Series flat, 90 Series full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles On a 30/50, 30/50B or 30/78 Series support profile 90 Series, full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles 24
25 DucoSun 100 D/150 D overslung Permanent external solar shading system. 100 D or 150 D Series solar shading systems have their aluminium blades above the support profiles at a fixed 45 degree blade mounting angle. All fascia profiles are available in a wide range of finishes. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. Technical Specifications 100 D 150 D - Blade: 100 D 150 D - Blade end plate Aluminium end plate for 100 D Series blades Aluminium end plate for 150 D Series blades - Blade holder: vertical/overslung (single, connecting and corner holder) vertical/overslung (single, connecting and corner holder) - Blade pitch: 107,5 mm 165 mm - Blade mounting angle: Maximum span: 2274 mm 2645 mm - Blade holder spacer N/a - Finish: With plastic stop With fascia profile - Installation: With standard wall bracket With strut and wall anchor > DucoSun 100 D overslung > DucoSun 150 D overslung On a 30/50, 30/50B or 30/78 Series support profile 150 Series flat, 175 Series flat, 90 Series full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles For fitting blades pitched at 140 mm On a 30/50, 30/50B or 30/78 Series support profile 90 Series, full bullnose For 30/50B or 30/78 Series support profiles For 30/50 Series support profiles ducosun 100 d/150 D underslung 100 d/150 D overslung 25
26 DucoSun 100 D intermediate Permanent external solar shading system. 100 D Series solar shading systems have their aluminium blades in between the support profiles at a fixed 45 degree blade mounting angle. A fascia profile is used to provide the finish. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 D intermediate Technical Specifications - Blade: 100 D - Blade end plate Aluminium end plate for 100 D Series blades - Blade holder: framed/intermediate (single, connecting and corner holder) - Blade pitch: 107,5 mm - Blade mounting angle: 45 - Maximum span: 2274 mm - Blade holder spacer - Finish: With fascia profile - Installation: With standard wall bracket With strut and standard wall anchor - Auxiliary holders: N/a 100 Series, semi-bullnose For 86/95 Series support profiles For 86/95 Series support profiles 50/12 Series support profile 26
27 DucoSun 100 D, framed Permanent external solar shading system. 100 D Series solar shading systems have their aluminium blades contained in a frame at a fixed 45 degree blade mounting angle. The frame is finished using a flat or a full bullnose fascia. Overhang-dependent, the systems are fixed to the façade not just with bracketry, but also with struts. > DucoSun 100 D, framed Technical Specifications - Blade: 100 D - Blade end plate: Aluminium end plate for 100 D Series blades - Blade holder: framed/intermediate (single, connecting and corner holder) - Blade pitch: 107,5 mm - Blade mounting angle: 45 - Maximum span: 2274 mm - Finish: With frame profile - Installation: With standard wall bracket With strut and standard wall anchor - Auxiliary holders: 100 Series full bullnose or 100 Series flat For flat 100 Series frame profiles For flat 100 Series frame profiles 30/12 Series support profile for rectangular frames 50/12 Series support profile for corner frames ducosun 100 d intermediate - framed 27
28 DucoSun 100 D/150 D vertical Permanent external solar shading system. 100 D or 150 D Series solar shading systems have their aluminium blades fitted against the support profiles at a fixed 45 degree blade mounting angle. > DucoSun 100 D vertical > DucoSun 150 D vertical Technical Specifications 100 D 150 D - Blade: 100 D 150 D - Blade end plate Alu end plate for 100 D Series blades Alu end plate for 150 D Series blades - Blade holder: vertical/overslung (single, connecting and corner holder) vertical/overslung (single, connecting and corner holder) - Blade pitch: 127,5 mm 190 mm - Blade mounting angle: Maximum span: 2274 mm 2645 mm - Installation: With standard support profiles 30/50, 30/78 or 50/12 For 30/50 Series support profiles 30/50, 30/78 or 50/12 For 30/50 Series support profiles 28
29 29 completed project
30 DucoSun Ellips DucoSun Ellips is the new name for DucoSun F. This solar shading system is available with either fixed or electrically adjustable blades. They are installed to the support system on-site (either horizontally or vertically). This system allows for a wide variety of blade mounting angles. This ensures that the system can shade the area optimally regardless of the glazed surface and the position of the sun throughout the day. The ellipsoid blade styles admit high levels of diffused daylight. They are available in a choice of seven sizes: DucoSun Ellips offers architects a wide freedom of design. > The ellipsoid blade styles admit high levels of diffused daylight. > The compact fitting dimensions provide optimal shading performance. > Available in a choice of 7 blade types. > Wide variety of fitting applications. 30
31 Basic components > Solar shading blades > Support profiles > End caps 60/100 Series support profile 0 end cap 45 end cap 76 62,7 > Blade holders Maximum span 60/40 Multifit Series clamp fixing bracket 80/40 (80/80, 80/120) Multifit Series clamp fixing bracket 40 (80, 120) Multifit Series base 0 Unifit Series clamp fixing bracket Unifit Series clamp fixing bracket On the following pages you will find tabulated values along with the maximum recommended blade length for each type of solar shading system. These values apply provided following conditions are met: > The solar shading blades should be fitted using : Screws in between 2 non Duco assembly plates (situation 1) ; Bolts and two end caps against a fixed structure or construction according to the instructions of Duco (situation 2); Bolts, two end caps, T bolts and a Duco support profile against Ymin. a fixed structure or construction according to the instructions of Duco (situation 3). > The Ymin distances should be observed (situations 2 and 3). > The maximum blade deviation should be 15 mm (compliant to European Directive ENV ). Other span options can be considered. Please feel free to contact Duco for assistance with calculating what you need for your specific project. Situation 1 Situation 2 Situation 3 ducosun ellips 31
32 DucoSun Ellips intermediate Permanent external solar shading system. The aluminium solar shading blades are held in place at a fixed angle of 0 or 45 between end caps. The amount of clearance between two solar shading blades (blade pitch) depends on blade type and blade mounting angle. > DucoSun Ellips intermediate Situation 1: Fitting a blade between two non Duco bespoke assembly plates (Please see for full details of maximum sizes.) Situation 2: Fitting a blade between two Duco end caps between a fixed structure Situation 3: Fitting a blade between two Duco end caps and support profile between a fixed structure Maximum span With a wind load of: Ellips blade Blade mounting angle Ymin. distance (mm) (C-C of fixings) 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 31 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance.. Technical Specifications - Ellips blade: 100, 150, 200, 250, 300, 350, Blade pitch: Dependent on blade type and blade mounting angle - Blade mounting angle: 0 or 45 32
33 > DucoSun Ellips multifit DucoSun Ellips multifit Permanent external solar shading system. The aluminium solar shading blades are fitted to aluminium support profiles at a fixed blade mounting angle using the patented Multifit system. This system consists of a base and a clamp fixing bracket. These two parts are linked together with a prong. This means that 11 positions in 15 increments are possible. The amount of clearance between two solar shading blades (blade pitch) depends on blade type and blade mounting angle. Maximum span With a wind load of: Ellips blade Multifit width (mm) 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) 60/ / / / / / / / / / / / / / / / Important: The above values are applicable if all conditions set out on page 31 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications - Ellips blade: 200, 250, 300, 350, Blade pitch: Dependent on blade type and blade mounting angle - Blade mounting angle: Multit base (width): 40mm 80mm 120mm - Multifit fixing bracket: 60/40 80/40 60/80 80/80 80/120 ducosun ellips intermediate multifit 33
34 > DucoSun Ellips unifit DucoSun Ellips unifit Permanent external solar shading system. The aluminium solar shading blades are fitted to aluminium support profiles at a fixed blade mounting angle of 0 or 45 using Unifit clamp fixing brackets. The amount of clearance between two solar shading blades (blade pitch) depends on blade type and blade mounting angle. Maximum span Unifit: With a wind load of Ellips blade Clamp fixing bracket( ) width (mm) 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 31 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications Technische eigenschappen - Ellips blade: 150, 200, 250, Blade pitch: Dependent on blade type and blade mounting angle - Blade mounting angle: 0 or 45 - Unifit Series base 40mm 34
35 > DucoSun Ellips moveable DucoSun Ellips moveable Permanent external solar shading system. The aluminium solar shading blades are electrically adjusted. The spring shafts reduce the clearance between the blades and the support system to a minimum. The amount of clearance between two solar shading blades (blade pitch) depends on blade type and any possible overlap between the solar shading blades. Maximum span With a wind load of: Ellips blade 600 Pa (±115km/h) Technische eigenschappen 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 31 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications - Ellips blade: 200, 250, 300, 350, Blade pitch: Dependent on the type of solar shading blade and any possible overlap between - Blade mounting angle: electrically adjustable ducosun ellips unifit moveable 35
36 DucoSun Cubic DucoSun Cubic is available with either fixed or electrically adjustable solar shading blades. They are installed to the support system on-site (either horizontally or vertically). Depending upon the type, fixed solar shading blades are fitted at a blade mounting angle of 0 or 90. Together with the rectangular shape of the solar shading blade, this produces a very clean-cut effect. When fully closed, the electrically adjustable solar shading blades provide highly effective sun protection. The closed solar shading blades and the façade face are aligned and, therefore, form a perfect unit. > Clean-cut rectangular blade geometry. > The closed solar shading blades and the façade face are aligned and, therefore, form a perfect unit. 36
37 Basic components > Solar shading blades Cubic Series solar shading blade 300 Cubic Series solar shading blade 400 Cubic Series solar shading blade > End caps: Cubic Series 45 end cap 200 Cubic Series 0 end cap > Blade holders Unifit 0 Cubic Maximum span On the following pages you will find tabulated values along with the maximum recommended blade length for each type of solar shading system. These values apply provided following conditions are met: > The solar shading blades should be fitted using : Screws in between 2 non Duco assembly plates (situation 1) ; Bolts and two end caps against a fixed structure or construction according to the instructions of Duco (situation 2); Bolts, two end caps, T bolts and a Duco support profile against Ymin. a fixed structure or construction according to the instructions of Duco (situation 3). > The Ymin distances should be observed (situations 2 and 3). > The maximum blade deviation should be 15 mm (compliant to European Directive ENV ). This means that under no circumstances the maximum dimensions listed in the tables contained in this product brief must never be exceeded. Other span options can be considered. Please feel free to contact Duco for assistance with calculating what you need for your specific project. Situation 1 Situation 2 Situation 3 ducosun Cubic 37
38 > DucoSun Cubic intermediate DucoSun Cubic intermediate Permanent external solar shading system. The aluminium solar shading blades are held in place at a fixed blade mounting angle of 0 or 90 between end caps. The amount of clearance between two solar shading blades (blade pitch) depends on blade type. Situation 1: Fitting a blade between two non Duco bespoke assembly plates (Please see for full details of maximum sizes.) Situation 2: Fitting a blade between two Duco end caps between a fixed structure Situation 3: Fitting a blade between two Duco end caps and support profile between a fixed structure Maximum span With a wind load of: Cubic Series solar shading Blade mounting angle Ymin. distance (mm) (C-C of fixings) 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 37 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications - Cubic Series solar shading blade: 200, 300, Blade pitch: Dependent on the type of solar shading blade - Blade mounting angle: 0 or 90 38
39 > DucoSun Cubic unifit DucoSun Cubic unifit Permanent external solar shading system. The aluminium solar shading blades are fitted to aluminium support profiles at a fixed 0 degree blade mounting angle using Unifit clamp fixing brackets. The amount of clearance between two solar shading blades (blade pitch) depends on blade type. Maximum span With a wind load of: Cubic Series solar shading Blade mounting angle Technical Specifications Ymin. distance (mm) (C-C of fixings) 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 37 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. - Cubic Series solar shading: 200, Blade pitch: Dependent on the type of solar shading blade - Blade mounting angle: 0 - Unifit Series base (width): 40mm ducosun Cubic intermediate Unifit 39
40 > DucoSun Cubic moveable DucoSun Cubic moveable Permanent external solar shading system. The aluminium solar shading blades are electrically adjusted. The spring shafts reduce the clearance between the blades and the support system to a minimum. The amount of clearance between two solar shading blades (blade pitch) depends on blade type and any possible overlap between the solar shading blades. Maximum span Cubic Series solar shading 600 Pa (±115km/h) With a wind load of: 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 37 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications - Cubic Series solar shading: 200, 300, Blade pitch: Dependent on the type of solar shading blade and any possible overlap between solar - Blade mounting angle: electrically adjustable 40
41 41 completed project
42 DucoSun Linear DucoSun Linear is available with either fixed or electrically adjustable solar shading blades. They are installed to the support system on-site (either horizontally or vertically). The fixed solar shading blades are fitted at a blade mounting angle of 45. Combined with the parallelogram shaped solar shading blade, a very beautiful effect is achieved. When fully closed, the electrically adjustable solar shading blades provide highly effective sun protection. The closed solar shading blades and the façade face are aligned and, therefore, form a perfect unit. > Very beautiful blade geometry (parallelogram). > The closed solar shading blades and the façade face are aligned and, therefore, form a perfect unit. > Full solar shading with blades closed. 42
43 Basic components > Solar shading blades 200 Linear Series solar shading blade 300 Linear Series solar shading blade > End caps Linear Series 0 LH end cap 200 Linear Series 0 LH end cap > Blade holders Unifit 45 Linear Maximum span On the following pages you will find tabulated values along with the maximum recommended blade length for each type of solar shading system. These values apply provided following conditions are met : > The solar shading blades should be fitted using: Screws in between 2 non Duco assembly plates (situation 1) ; Bolts and two end caps against a fixed structure or construction according to the instructions of Duco (situation 2); Bolts, two end caps, T bolts and a Duco support profile against a fixed structure or construction according to the instructions Ymin. of Duco (situation 3). > The Ymin distances should be observed (situations 2 and 3). > The maximum blade deviation should be 15 mm (compliant to European Directive ENV ). This means that under no circumstances the maximum dimensions listed in the tables contained in this product brief must never be exceeded. Other span options can be considered. Please feel free to contact Duco for assistance with calculating what you need for your specific project. Situation 1 Situation 2 Situation 3 ducosun linear 43
44 DucoSun Linear intermediate Permanent external solar shading system. The aluminium solar shading blades are held in place at a fixed blade mounting angle of 0 or 45 between end caps. The amount of clearance between two solar shading blades (blade pitch) depends on blade type. > DucoSun Linear intermediate Situation 1: Fitting a blade between two non Duco bespoke assembly plates (Please see for full details of maximum sizes.) Situation 2: Fitting a blade between two Duco end caps between a fixed structure Situation 3: Fitting a blade between two Duco end caps and support profile between a fixed structure Maximum span With a wind load of: Linear Series solar shading Blade mounting angle Ymin. distance (mm) (C-C of fixings) 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 43 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications - Linear Series solar shading: 200, 300, Blade pitch: Dependent on the type of solar shading blade - Blade mounting angle: 45 44
45 > DucoSun Linear unifit DucoSun Linear unifit Permanent external solar shading system. The aluminium solar shading blades are fitted to aluminium support profiles at a fixed 45 degree blade mounting angle using Unifit clamp fixing brackets. The amount of clearance between two solar shading blades (blade pitch) depends on blade type. Situation 1: Fitting a blade between two non Duco bespoke assembly plates (Please see for full details of maximum sizes.) Situation 2: Fitting a blade between two Duco end caps between a fixed structure Situation 3: Fitting a blade between two Duco end caps and support profile between a fixed structure Maximum span Linear Series solar shading Clamp fixing bracket( ) Unifit : Important: The above values are applicable if all conditions set out on page 43 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications width (mm) 600 Pa (±115km/h) With a wind load of: 800 Pa (±130km/h) 1250 Pa (±165km/h) Linear Series solar shading 200, Blade pitch: Dependent on the type of solar shading blade - Blade mounting angle: 45 - Unifit Series base (width): 40mm ducosun linear intermediate Unifit 45
46 > DucoSun Linear moveable DucoSun Linear moveable Permanent external solar shading system. The aluminium solar shading blades are electrically adjusted. The spring shafts reduce the clearance between the blades and the support system to a minimum. The amount of clearance between two solar shading blades (blade pitch) depends on blade type and any possible overlap between the solar shading blades. Maximum span With a wind load of: Linear Series solar shading 600 Pa (±115km/h) 800 Pa (±130km/h) 1250 Pa (±165km/h) Important: The above values are applicable if all conditions set out on page 43 are satisfied. If any one of these conditions fails, strength calculation as dictated by the specific project situation will need to be performed again. Contact Duco for further assistance. Technical Specifications Technische eigenschappen - Linear Series solar shading: 200, Blade pitch: Dependent on the type of solar shading blade and any possible overlap between solar shading blades. - Blade mounting angle: electrically adjustable 46
47 47 completed project
48 Bedrijvenlaan 2 - B-8630 Veurne - Belgium - tel fax info@duco.eu - Subject to change:
ARCHITECTURAL SUN CONTROL
ARCHITECTURAL SUN CONTROL en HOME OF OXYGEN An optimal indoor climate is healthy and gives a good feeling. Duco developed its Green Building Solution for this reason where basic ventilation, intensive
More informationARCHITECTURAL SUN CONTROL
(en) ARCHITECTURAL SUN CONTROL We inspire at www.duco.eu HOME O F OXYGEN Duco Ventilation & Sun Control provides every building with a healthy supply of oxygen. With a comprehensive range of innovative
More informationSolar C - Fixed Solar Shading
Solar C - Fixed Solar Shading An important part of the design process is to consider when it is beneficial to protect glazing from the sun. If glare is controlled by other means, such as internal blinds,
More informationArchitects: Carlos Ferrater, Lucía Ferrater and Xavier Martí Photographer: Alejo Bagué NOTEAL EFFECTIVE PRIVACY AND SOLAR PROTECTION SHUTTER
Architects: Carlos Ferrater, Lucía Ferrater and Xavier Martí Photographer: Alejo Bagué NOTEAL EFFECTIVE PRIVACY AND SOLAR PROTECTION SHUTTER 2 DR Technal NOTEAL, designer solar protection The concept NOTEAL
More informationMoving Shades. Above : Residential building Product : HunterDouglas Sliding Shutter Screen Special : bronze-tangerine 2 sides combination
Sliding Shutter Screen Sliding Shutter Screen Moving Shades Above : Residential building Product : HunterDouglas Sliding Shutter Screen Special : 113105 bronze-tangerine 2 sides combination SLIDING SHUTTER
More informationsolar protection systems Cantilevered, horizontal, vertical and noise-absorbing sunshade systems Construction Specialties
solar protection systems Cantilevered, horizontal, vertical and noise-absorbing sunshade systems Construction Specialties system modules ß Birdsmouth Brackets in aluminium, (30º), 45º and 90º (for blades
More informationArchitects : Nuno Leónidas and Frederico Valsassina - Photography: TECHNAL SUNEAL MULTIFUNCTION BRISE-SOLEIL
Architects : Nuno Leónidas and Frederico Valsassina - Photography: TECHNAL SUNEAL MULTIFUNCTION BRISE-SOLEIL SUNEAL, between design and efficiency A solution serving your projects To meet the multiple
More informationGYPSE TRADITIONAL BALUSTRADE. Photography: V. Bigeard
GYPSE TRADITIONAL BALUSTRADE Photography: V. Bigeard GYPSE / A BALUSTRADING SYSTEM WITH COUNTLESS OPPORTUNITIES AND MINIMALIST LINES GYPSE, A LEADING DESIGN With an aesthetic metal effect and design both
More informationWall flashing profiles FP 60 WA 1 WA 150 WA 1 - ÜK WA 1 - Ü 150 E
Wall flashing profiles FP 60 WA 1 WA 150 WA 1 - ÜK 150-275 WA 1 - Ü 150 E 1 F Ü R D I E ZU K U N FT G E DAC HT. The alwitra waterproofing system alwitra wall flashing profiles are part of the practically
More informationDUALCASE VERSATILE ALUMINIUM SIGN SYSTEM
VERSATILE ALUMINIUM SIGN SYSTEM Universal Components Ltd. May 2007 Introduction Nothing beats DualCase for speed of fabrication, aesthetic appearance and easy maintenance. With the minium of components
More informationOKASOLAR P Glazing with direction-sensitive privacy screening
P Glazing with direction-sensitive privacy screening P is an insulating glass with fixed; vertical louvres in the cavity between the glass panes P enables partial transparency in one direction at the same
More informationSilent Gliss Roller Blind Systems
Silent Gliss Roller Blind Systems The Silent Gliss Advantage The roller blinds clean lines complement modern architecture and interior design perfectly. They allow maximum shading with minimum window obtrusion.
More informationReflex-Rol SOLAR GLARE, REFLECTION AND HEAT CONTROL SYSTEMS REFLEX-ROL BLINDS: CONTROLLING SOLAR GLARE, REFLECTION AND HEAT
REFLEX-ROL BLINDS: CONTROLLING SOLAR GLARE, REFLECTION AND HEAT REVISED EDITION Incorporates latest data to EN 13363-1 & EN 14501 Reflex-Rol SOLAR GLARE, REFLECTION AND HEAT CONTROL SYSTEMS Reflex-Rol
More informationSCW Series Product Assembly Manual 2008 SCW CURTAIN WALL
SCW Series Product Assembly Manual 2008 SCW CURTAIN WALL 2.1.ii 07.08 SCW Curtain Wall Introduction The Company Senior Aluminium Systems are a group of companies based in the United Kingdom supported through
More informationInstallation Instructions
Installation Instructions Roof edge trim profile Series TAG multi-piece aluminium profile Front face height: 250-1050 mm supplied with patented 4F brackets as standard height-adjustable, horizontally moveable,
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationClearVue Roofing System Technical Manual
Technical Manual Components CLEARVUE RAFTER BRACKETS CV-02 2 Components CLEARVUE EXTRUSIONS CV-03 3 Components END PLATES - 6mm SHEET CV-04 4 Components END PLATES - 8mm SHEET CV-05 5 Components MECHANICAL
More informationFacade awnings from Griesser. Solozip II
Facade awnings from Griesser. Solozip II 2 Solozip II Solozip II Are you looking for a facade awning that provides needed solar shading even when it s windy? Our zip system is exactly what you need! The
More informationGEZE Fanlight OL 90 N
GEZE Fanlight OL 90 N Slimline fanlight opener with a wide diversity of variants This fanlight opener is used inwards for vertically installed rectangular windows with bottom, top, side hung or horizontally
More informationQ-DESIGNS BY Q-RAILING. Q-designs by Q-railing
Q-DESIGNS BY Q-RAILING CONTENT 2 Q-DESIGNS BY Q-RAILING WE DESIGN RAILING SYSTEMS Q-HANDRAIL Q-LINE SQUARE LINE QUICKRAIL EASY GLASS TOP EASY GLASS EVOLUTION PROJECTS What can you expect from Q-railing?
More informationSilent Gliss Roller Blind Systems
Silent Gliss Roller Blind Systems The Silent Gliss Advantage The roller blinds clean lines complement modern architecture and interior design perfectly. They allow maximum shading with minimum window obtrusion.
More informationAirfoil SOLAR PROTECTION AND SHADING SYSTEMS Solar protection systems Noise-absorbing blade systems Light-architecture at night
www.cs-france.fr Airfoil SOLAR PROTECTION AND SHADING SYSTEMS Solar protection systems Noise-absorbing blade systems Light-architecture at night Airfoil Blades and System Components Blade extruded from
More informationQ-RAILING DESIGNER SYSTEMS
Q-RAILING DESIGNER SYSTEMS THE IDEAL SOLUTION FOR EVERY RAILING PROJECT BRING YOUR VISION TO LIFE CONTENT WELCOME TO Q-RAILING, YOUR SOURCE FOR INNOVATIVE, HIGH GRADE, DESIGNER RAILING SYSTEMS. OUR SYSTEMS
More informationALUMINIUM BIFOLD DOORS
The Home of Aluminium Brochure ALUMINIUM BIFOLD DOORS AluminiumBifoldDoors INTRODUCING ALUFOLD The Aluhaus family group of products are made from premium aluminium components coupled with purpose designed
More informationHOW TO Fix Onduline Corrugated Bitumen Sheets
HOW TO Fix Onduline Corrugated Bitumen Sheets BBA BRITISH BOARD OF AGREMENT CERTIFICATE NO. 87 / 1823 W ROOFING PLAN IT Roofing components: Ridge Roof decking Apex Verge Barge board Purlins / battens Rafters
More informationheroal non-insulated profile systems
heroal non-insulated profile systems Non-insulated profile systems Top-quality materials, technical solutions fine-tuned to the smallest detail and a wide variety of design options distinguish the efficient
More informationargenta opening doors
invisible hinges Content Invisible neo... 4 Invisible... 12 Invisible Pro XS4... 20 Pivotica Pro... 26 Pivotica... 32 Magnotica... 36 CONCEALED HINGES To strive for an aesthetic design for both rotating
More informationSkylight Shading System Silent Gliss Skylight Shading Systems Silent Gliss 8600, 8700 & 8800
Skylight Shading System Silent Gliss 8800 Skylight Shading Systems Silent Gliss 8600, 8700 & 8800 The sun - an essential energy source of life. Daylight is vital to our lives, giving us the vigour to
More informationevolume Technical lighting without frills
evolume Technical lighting without frills Technical perfection for streets and roads Evolume combines excellent lighting properties and visual comfort with a modern cost-effective design. Thanks to its
More informationInsect. screens.... protect your privacy.
EN Insect screens... protect your privacy. Insect screens protect your privacy. During summer ventilation, it is a common occurrence to switch on the light and see a room full of insects. Insect screens
More informationGEZE SLIDING DOOR SYSTEMS
GEZE Perlan 140 Multi-faceted uses with individual accessories The discrete design supports every required room effect and makes the sliding door system with its accessories a guarantee for elegant and
More informationDesigned for Air Traffic Control Towers, the Aviation Shading System from Reflex-Rol
Designed for Air Traffic Control Towers, the Aviation Shading System from Reflex-Rol Imagine your ATCT goes down to reduced visibility status. Imagine the reduced landing fees due to reduced visibility
More informationAXIOM KE CANOPY Installation Guide
CI/SfB (35) Xy AXIOM KE CANOPY Installation Guide April 2016 1 PREPARATION AXIOM KE CANOPY COMPONENTS Item Nr. Description CS 57420 G AXIOM KE Canopy profile C 3000 H C Channel 19 x 38mm A WDN 21 H T bar
More informationPOOL ENCLOSURES LEIA & ALVA. Assembly manual
POOL ENCLOSURES LEIA & ALVA Assembly manual Rev. 07.2017 PARTS LIST Parts for rail installation: Rail Síncsavar screw 1 Plastic Síncsavar anchor 10 50 2 Rail Síncsavar connector 3 Arrest Síncsavar wedge
More informationSolar control devices; balance between thermal performance and daylight
International Conference Passive and Low Energy Cooling 991 Solar control devices; balance between thermal performance and daylight M. Mehrotra Architectural Association, Graduate School, London ABSTRACT
More informationE11.15 HANDLES AND LOCKCASES E11 BOTTOM HUNG OPEN IN WINDOWS
E11 BOTTOM HUNG OPEN IN WINDOWS HANDLES AND LOCKCASES 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Handles
More informationPANIC BARS Marking IN ACCORDANCE WITH 1125:1997/A1:2001
PANIC BARS Marking IN ACCORDANCE WITH 25:997/A:200 Exclusive PININFARINA design Full adaptability in application Quick and easy installation Reliable and safe performance Tested up to 2.000.000 cycles
More informationFramed by I N F I N I U M
Framed by INFINIUM A MODERN MASTERPIECE Like the finest pieces of art great architecture inspires. It evokes discussion and stirs emotions. At times it demands attention. Other times reflection. And at
More informationsalto safe 4028 A12 Turn-tilt windows
A12 Turn-tilt windows salto safe 4028 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. 32 9 388 88 81 - F. 32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com salto safe 4028 Contents 1. General
More informationSilent Gliss Roller Blind Systems
Silent Gliss Roller Blind Systems The Silent Gliss Advantage Silent Gliss offers the most comprehensive and technically advanced roller blind systems.their clean lines perfectly complement modern architecture
More informationSection 11 CABLE & ROD SYSTEMS, SIGN FIXING & SIGN STANDOFFS. Web. acrylicdesign.ie .
Section 11 CABLE & ROD SYSTEMS, SIGN FIXING & SIGN STANDOFFS Web. acrylicdesign.ie Email. sales@acrylicdesign.ie Acrylic Design 2004-2015 Mobile Cable System Components Single panel clamp Stand Off for
More informationINSTALLATION INSTRUCTIONS Aluminum Railing System
INSTALLATION INSTRUCTIONS FASCIA MOUNT SURFACE MOUNT OFFSET BASE SURFACE MOUNT STANDARD BASE CORE MOUNT Ø3" [Ø76 mm] 3 2 1 " [89 mm] 1 4 1 " [32 mm] 2 8 7 " [73 mm] 200 SERIES 300 SERIES 3 3 4 " [95 mm]
More informationSLIDING SYSTEMS. Product catalog 2017
SLIDING SYSTEMS Product catalog 2017 Grafipro Oy Product catalog 2017 Table of contents: 3 Areas of use 4 C rails C-30 is a company specialising in aluminium and plastic composite materials. Our expertise
More informationLIGHT MANAGEMENT MASTERED
LIGHT MANAGEMENT MASTERED Architects in planning rooms today have forgotten their faith in natural light. Depending on the touch of a finger to a switch, they are satisfied WHERE DESIGN AND PRECISION COME
More informationACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES WIRE MESH PARTITION FOLDING GATE
acorn WIRE ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES 10 22 13 WIRE MESH PARTITION 10 22 16 FOLDING GATE GUIDE Page 4 / 5 No. 130A All wire type for normal industrial use. 7, 8, 9, 10 and
More informationK12.12 SINGLE LOCKS SERIES 8600 K12 DOORS
K12 DOORS K12.12 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Door locks series 8600... K12.12.03 1.1.
More informationInstallation guide. ROCKFON VertiQ. ROCKFON System T, ROCKFON System HAT. Impact-resistant and high impact-resistant acoustic wall panel solutions
Installation guide ROCKFON ROCKFON System T, ROCKFON System HAT Impact-resistant and high impact-resistant acoustic panel solutions ROCKFON System T, ROCKFON System HATT Contents System selection...3 Edges
More informationFRANGISOLE (Sunblades)
www.metra.it FRANGISOLE (Sunblades) Shading systems METRA. ADDING VALUE TO YOUR HOME METRA. Design, Colour, Emotion. Italian style desired the world over. METRA s integrated systems have been created in
More informationGlass Systems. Technical Information on Pilkington Profilit Profiled Glass with System. - English Edition - Pilkington Profilit
Glass Systems Technical Information on Profiled Glass with System - English Edition - The - Delivery Programme Glass thickness 6 mm, flange height mm 6 7 0 K 3 8 K//7 3 6 7 6 6 6 6 6 6 50 39 486 K5 6 K3
More informationOverlapping panel Cladding system made up of horizontal overlapping panels fixed on a wooden or metal wall-mounted framework.
facade Overlapping panel Cladding system made up of horizontal overlapping panels fixed on a wooden or metal wall-mounted framework. Specification and installation guide Presentation of the system VMZ
More informationBeautiful balustrades DESIGNER FRAMELESS GLASS BALUSTRADES & POOL FENCES
Beautiful balustrades DESIGNER FRAMELESS GLASS BALUSTRADES & POOL FENCES CUBOID FACE-FIXED BALUSTRADE A discreet and invisibly fixed system for attaching glass balustrades and pool fencing without disturbing
More informationfrom page 586 from page 609
from page from page 0 from page from page 0 from page from page 0 from page 0 from page MSX. Design Standard components - MSX-B base: glass-fibre reinforced polyamide based (PA) technopolymer, black colour,
More informationargenta opening doors
invisidoor Invisible aluminium frame for interior doors Content invisidoor... 4 invisidoor AX / AX PRO... 10 invisidoor SD / SDX... 16 invisiplint... 22 general information... 27 THE INVISIDOOR CONCEPT
More informationInstallation of HORIZONT and HORIZONT HIGH pool enclosures
Installation of HORIZONT and HORIZONT HIGH pool enclosures Rev. 19.10.2017 PARTS LIST Parts for rail installation: Rail screw 6 x 60 Plastic anchor 10 x 50 Rail connector Arrest wedge [R-L] Pop rivet 4
More information21 C SHELVING SYSTEMS 21 C Shelving Systems consist of innovative products that provide visually appealing shelving and storage to any area. This syst
21 C SHELVING SYSTEMS 21 C SHELVING SYSTEMS 21 C Shelving Systems consist of innovative products that provide visually appealing shelving and storage to any area. This system is available in two unique
More informationInstallation Instructions
Installation Instructions Alpha SolarSmart On Roof Kits for the Installation of Alpha Solar Collectors onto Tile and Slate Type Roofs For Technical help or for Service call... ALPHA HELPLINE Tel: 0 77
More informationSURE SHADE External motorised operable and retractable aluminium louvres (external venetian blinds)
SURE SHADE External motorised operable and retractable aluminium louvres (external venetian blinds) An overview of available product types & construction specifications External venetian blinds have been
More informationAvery Dennison Architectural Window Films
Avery Dennison Architectural Window Films Solar Safety graphics.averydennison.eu/architectural-window Avery Dennison Architectural Window Films Avery Dennison Architectural Window Films can improve the
More informationSPG+S27 PATENT GLAZING. SPG+S27 Series Product Assembly Manual 1999
SPG+S27 PATENT GLAZING SPG+S27 Series Product Assembly Manual 1999 4.1.ii 03.99 SPG and S27 Patent Glazing Introduction The Company Senior Aluminium Systems are a group of companies based in the United
More informationK15.12 ROLLENBAND K15 DOORS
K15 DOORS 01.04.2015 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General characteristics....03 2. Application range....03
More informationK15.13 FACE FIXED DOOR HINGES K15 DOORS
K15 DOORS K15.13 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General... K15.13.03 2. 2-part hinge...
More informationC11.15 HANDLES AND LOCKCASES C11 SIDE HUNG WINDOWS
C11 SIDE HUNG WINDOWS C11.15 HANDLES AND LOCKCASES 01.03.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Handles
More informationCell Ceiling. Endless possibilities
Cell Ceiling Hunter Douglas Cell Ceilings enable architects to design an open ceiling with high-performance aluminium. With a wide variety of cells and patterns, these ceilings offer maximum freedom in
More informationK11.13 THREE-POINT LOCKS SERIES 8400 K11 DOORS
K11 DOORS K11.13 THREE-POINT LOCKS SERIES 8400 01.04.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Three-point
More informationStabalux T. 5.0 Stabalux T 1
5.0 1 5.1 - System 2 5.1.1 System properties 2 5.1.2 System profiles 6 5.2 - Processing information 9 5.2.1 Mullion-transom joint 9 5.3 - Design 11 5.3.1 System cross sections 11 5.3.2 Notes 13 System
More informationQ-RAILING DESIGNER SYSTEMS
Q-RAILING DESIGNER SYSTEMS THE IDEAL SOLUTION FOR EVERY RAILING PROJECT BRING YOUR VISION TO LIFE CONTENT WELCOME TO Q-RAILING, YOUR SOURCE FOR INNOVATIVE, HIGH GRADE, DESIGNER RAILING SYSTEMS. OUR SYSTEMS
More informationTABLE OF CONTENTS. 17mm ALUMINUM WALL MOUNTED FRAME. 22mm TAMPER RESISTENT FRAME. 36mm ULTRA THIN BACKLIT ALUMINUM FRAME
H A R D W A R E A N D A C C E S S O R Y G U I D E TABLE OF CONTENTS 17mm ALUMINUM WALL MOUNTED FRAME 22mm TAMPER RESISTENT FRAME 36mm ULTRA THIN BACKLIT ALUMINUM FRAME 50MM DOUBLE SIDED ALUMINUM FRAME
More informationmarkilux Form follows function the conservatory awning with contrasting shapes designed down to the last detail optionally with zip system
safe timeless beautiful 88 Form follows function the conservatory awning contrasting shapes designed down to the last detail optionally zip system wnings 110 / ccessories 103 rated to wind resistance class
More informationExpand your horizons German High Quality Aluminium Door & Window Systems
Expand your horizons German High Quality Aluminium Door & Window Systems SF 20 Sliding System / All-Glass The SUNFLEX all-glass sliding system SF 20 enables the individual parallel sliding panels to be
More informationPorcelain Enamel Signs Tin Metal Signs
Porcelain Enamel Signs Tin Metal Signs SMALT BRNO, spol. s r.o. Palace Sidonie, Hybešova 21 602 00 Brno Czech Republic Phone: +420 543 210 756 Fax: +420 543 210 757 E-mail: info@smalt.cz smalt.com Porcelain
More informationFEET, WHEELS, FLOOR FASTENINGS, SUPPORTS
SYSTEM COMPONENTS FEET, WHEELS, FLOOR FASTENINGS, SUPPORTS s t r oppu S, s gn i n e t s af r oo l F, s l eehw, t e ef FEET, WHEELS, FLOOR FASTENINGS, SUPPORTS 136 MINITEC PROFILE SYSTEM BASE AND TRANSPORT
More informationPRODUCT INFORMATION FOR ARCHITECTS, ENGINEERS AND INSTALLERS Insulation spacers for commercial metal roofing
www.roofrazor.com.au PRODUCT INFORMATION FOR ARCHITECTS, ENGINEERS AND INSTALLERS Insulation spacers for commercial metal roofing 1.0WHAT IS THE ROOF RAZOR? u The Roof Razor is a roof insulation spacer
More informationscreens UNDERSTANDING SCREENS PANEL WALL ADD-ON SCREEN BASICS PLANNING WITH WALL PANEL ADD-ON SCREENS... 94
UNDERSTANDING SCREENS................................. PANEL WALL ADD-ON SCREEN BASICS......................... PLANNING WITH WALL PANEL ADD-ON SCREENS................. GLASS BLADES FOR PANELS WITH INSET
More informationCORSO TELESCOPIC PATIO ENCLOSURES COMPLETE YOUR HOME...
CORSO TELESCOPIC PATIO ENCLOSURES www.alukov.co.uk COMPLETE YOUR HOME... INTRODUCTION Dear customers and business partners, Our company Alukov is proud to present our latest and most advanced product range,
More informationTotal comfort for every conservatory or patio roof
Total comfort for every conservatory or patio roof Conservatory awnings WGM Sottezza/ Sottezza Lux www.weinor.co.uk WGM Sottezza/Lux 1 WGM Sottezza under patio roof Conservatory awnings WGM Sottezza/ Sottezza
More informationFURNITURE HARDWARE & ACCESSORIES - PART 2 : SHELF SUPPORT AND SHELVING SYSTEMS
www.hafeleindia.com FURNITURE HARDWARE & ACCESSORIES - PART 2 : SHELF SUPPORT AND SHELVING SYSTEMS ABOUT ITALIANA FERRAMENTA ITALIANA FERRAMENTA is specialized in the production of high quality accessories
More informationBar supports. Bar supports
APPLICATIONS TEKNOMEGA bar supports make it possible to support efficiently and conveniently all copper and/or aluminum bar systems to be made inside an electric cabinet. The versatility and universality
More informationQ-RAILING SYSTEMS THE IDEAL SOLUTION FOR EVERY PROJECT THE PREMIUM BRAND IN RAILING SYSTEMS
Q-RAILING SYSTEMS THE IDEAL SOLUTION FOR EVERY PROJECT THE PREMIUM BRAND IN RAILING SYSTEMS BRING YOUR VISION TO LIFE WELCOME TO Q-RAILING, YOUR SOURCE FOR INNOVATIVE, HIGH GRADE, DESIGNER RAILING SYSTEMS.
More informationDiscuss your project with a Locker Group Architectural Consultant at the outset, to ensure you achieve the best results.
Technical Data Sheet PIC PERF SPECIFICATION Sheet No: LP-105.3 April 2011 Pic Perf is a digitally created image produced in Perforated Metal. Pic Perf is available in a wide variety of specifications,
More informationMake it Make itbeautiful. Last a Lifetime. Safe. Make it
Make it Make itbeautiful Last a Lifetime Make it Safe Railing We carry a variety of styles for a lifetime of low maintenance durability so that you can choose the railing that suits you best! Customize
More informationGardman Lean-to Greenhouse Assembly Instructions
Page 1 Gardman Lean-to Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free
More informationASS 70 FD folding/sliding door installation guide
ASS 70 FD folding/sliding door installation guide 2 Preparation IMPORTANT These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the
More informationCROSSBAR RAFTER ISOMETRIC
Super Sky Products' typical glazing system consists of glass panels or "lites" which are attached to the main framing members using extruded aluminum "retainers" or "pressure plates". These retainers are
More informationA11.15 HANDLES AND LOCKCASES A11 TURN-TILT WINDOWS
A11 TURN-TILT WINDOWS A11.15 HANDLES AND LOCKCASES 01.03.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Handles
More informationWelcome to Optima! Do you run a professional sign company? Would you like to offer your customers world-class signage solutions at attractive prices?
Product Catalogue 2012 Welcome to Optima! Do you run a professional sign company? Would you like to offer your customers world-class signage solutions at attractive prices? How about saving time by using
More informationThe Architectural Range
The Architectural Range The Architectural Range Building on our experience in film and theatre lighting, LEE Filters have introduced a range of lighting filter products specifically designed for use in
More informationSYSTEM OWNER S MANUAL
From the makers of INCRA JIG SYSTEM OWNER S MANUAL W hat does an INCRA tool do better than any other? Just ask that question to any of the thousands of satisfied INCRA router table or table saw fence owners
More informationINSTALLATION GUIDE DUOFUSE SLAT WALL SYSTEM
06/2013 ENG 1 INSTALLATION GUIDE DUOFUSE SLAT WALL SYSTEM The Duofuse wood composite slat wall system is much more durable than wooden fences, and correct installation is necessary to enjoy the fences
More informationTHE NEXT GENERATION OF BIFOLD DOORS
THE NEXT GENERATION OF BIFOLD DOORS INTRODUCING ALUFOLD THE NEW LEADER IN ALUMINIUM BIFOLD DOORS The Aluhaus fmily group of products are made from premium aluminium components coupled with purpose designed
More informationSPW500 Thermal Framing SPW500. Product Assembly Manual 2012 Thermal Framing
SPW500 Thermal Framing SPW500 Product Assembly Manual 2012 Thermal Framing SPW.500.ii 01.12 SPW500 Thermal Framing Introduction The Company Senior Architectural Systems Ltd are a group of companies based
More informationKentaur Turnstiles Kentaur Full-Height Gates
Kentaur Turnstiles Kentaur Full-Height Gates Expertise in perimeter protection «We attach great importance to perimeter protection on our premises. An intelligent fence system and automatic full-height
More informationPRODUCT CODE FIXTURE COLOR OPTIC BEAM WATTAGE COLOR TEMP + HOUSING DRIVER VOLTAGE. DB Deep Black FL Flood 30º K I 1 IC/Air Tight Housing MF
Extractable 6" LED Downlight Projector Concept: LED recessed extractable downlight. Housings: Non IC plaster frame or IC/Air tight housing available. Materials: Head, front ring and heat sink in die-cast
More informationVEUE PIVOT ARM INSTALLATION MANUAL. February 2017
VEUE PIVOT ARM INSTALLATION MANUAL February 2017 CONTENTS February 2017 This manual is to be read in conjunction with the Product Specifications & Assembly manual SECTION NO. DESCRIPTION PAGE NO. SECTION
More informationFURNITURE HARDWARE & ACCESSORIES - PART 3 : LEVELLERS AND HANGERS
www.hafeleindia.com FURNITURE HARDWARE & ACCESSORIES - PART 3 : LEVELLERS AND HANGERS ABOUT ITALIANA FERRAMENTA ITALIANA FERRAMENTA is specialized in the production of high quality accessories and ironmongery
More informationIMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)
ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions
More informationList of Contents. Trunking systems. Selection of surface finish. Equipotential bonding. Cable ladders. Cable trays/ luminaire rails.
List of Contents Trunking systems Ductel Twist Trunking system for electricity, telecoms and data solutions. The trunking is made of aluminium and is available with 45 mm and 80 mm openings. Plastic trunking
More informationInstallation Instructions: Urbanline Alu Selekta Clad
Product description Ecology Technical data Urbanline Alu Selekta Clad (selekta façade profiles and heritageselekta façade profiles) are identical in terms of their core material and surface texture. However,
More informationArchitectural Testing AAMA 501 TEST REPORT. Report Number: C Rendered to: Tubelite, Inc. Walker, Michigan
Architectural Testing AAMA 501 TEST REPORT Report Number: C1529.01-450-44 Rendered to: Tubelite, Inc. Walker, Michigan MODEL DESIGNATION: E4500 PRODUCT TYPE: Non-Thermal Storefront This report contains
More informationextend your outdoor lifestyle
extend your outdoor lifestyle www.laserlite.com.au Up to 50% better heat reduction than standard sheet # only Laserlite has the technology Laserlite is the only polycarbonate sheet product in Australia
More information60.AL. Lauder. Facade LAUDESCHER
60.AL Facade Lauder LAUDESCHER General performance Industrial manufacturing process Rebated using halved joint assembly guaranteeing perfect hold of the linear panel. Solid wood All of our solid wood is
More information