RF Characterization Report
|
|
|
- Sharon Phillips
- 6 years ago
- Views:
Transcription
1 RF36 Series Cable Assemblies RF36-SJ-SJ-3 RF36-RP-RP-36 RF36-SP-SP-36 RF36-3SP-3SP-36 RF36-3RP-3RP-36 RF36-5SP-5SP-35 RF36-5BJ-5BJ-3 RF36-6BJ-6BJ-35 RF36-7SP-7SP-33 RF36-7RP-7RP-37 RF36-7BJ-7BJ-36 RF36-S7RP4-S7RP4-35 RF36-S7SP4-S7SP4-35 RF36-PN-PN-5 RF36-V3SJ4-V3SJ4-35 RF36-V3SP4-V3SP4-35 RF36-V3RP4-V3RP4-35 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Samtec Inc. Phone: Park East Blvd. -8-SAMTEC-9 (US & Canada) Fax: New Albany IN USA RF@samtec.com Report Revision: /8/ Samtec, Inc. 5 All Rights Reserved
2 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Table of Contents Test Setup Information... Scope:... Product Description:... Test Calibration:... 3 Adapter Use:... 3 Definition of Assembly under Test:... 4 Port Designations:... 4 Legend for Plots:... 4 Results Summary... 5 RF36-SJ-SJ RF36-RP-RP RF36-SP-SP RF36-3SP-3SP RF36-3RP-3RP RF36-5SP-5SP RF36-5BJ-5BJ-3... RF36-6BJ-6BJ RF36-7SP-7SP RF36-7RP-7RP RF36-7BJ-7BJ RF36-S7RP4-S7RP RF36-S7SP4-S7SP RF36-PN-PN RF36-V3SJ4-V3SJ RF36-V3SP4-V3SP RF36-V3RP4-V3RP Instrument Setup:... Test Fixtures:... 3 Samtec Inc. Phone: Park East Blvd. -8-SAMTEC-9 (US & Canada) Fax: New Albany IN USA RF@samtec.com Report Revision: /8/ Samtec, Inc. 5 Page:ii All Rights Reserved
3 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Test Setup Information Scope: To perform characterization tests,, and Voltage Standing Wave Ratio. Product Description: The table below presents a description of the different RF36 series cable assemblies that were tested. Part Number Length Termination End Termination End RF36-SJ-SJ-3 3 mm MCX, Straight, Jack MCX, Straight, Jack RF36-RP-RP mm MCX, Right Angle, Plug MCX, Right Angle, Plug RF36-SP-SP mm MCX, Straight, Plug MCX, Straight, Plug RF36-3SP-3SP mm MMCX, Straight, Plug MMCX, Straight, Plug RF36-3RP-3RP mm MMCX, Right Angle, Plug MMCX, Right Angle, Plug RF36-5SP-5SP mm TNC, Straight, Plug TNC, Straight, Plug RF36-5BJ-5BJ-3 3 mm TNC, Straight, Bulkhead Jack TNC, Straight, Bulkhead Jack RF36-6BJ-6BJ mm NTPE, Straight, Bulkhead Jack NTPE, Straight, Bulkhead Jack RF36-7SP-7SP mm SMB5, Straight, Plug SMB5, Straight, Plug RF36-7RP-7RP-37 RF36-7BJ-7BJ-36 RF36-S7RP4-S7RP4-35 RF36-S7SP4-S7SP mm 36 mm 35 mm SMB5, Right Angle, Plug SMB5, Straight, Bulkhead Jack SSMB, Right Angle, Plug SMB5, Right Angle, Plug SMB5, Straight, Bulkhead Jack SSMB, Right Angle, Plug 35 mm SSMB, Straight, Plug SSMB, Straight, Plug RF36-PN-PN-5 5 mm SMA, Straight, Jack SMA, Straight, Jack RF@samtec.com Report Revision: /8/ Page:
4 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Part Number Length Termination End Termination End RF36-V3SJ4-V3SJ mm MMCXV, Straight, Jack MMCXV, Straight, Jack RF36-V3SP4-V3SP mm MMCXV, Straight, Plug MMCXV, Straight, Plug RF36-V3RP4-V3RP mm MMCXV, Right Angle, Plug MMCXV, Right Angle, Plug RF@samtec.com Report Revision: /8/ Page:
5 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Test Calibration: Calibration is performed using Agilent electronic calibration module, PN or Agilent mechanical calibration kit, PN 855D to the calibration point below. Any adapters beyond this point are included in the measurements. Adapter Use: (Sample setup of adapters, actual setup not depicted.) Each port uses at least one precision adapter capable of mating to the assembly under test. Any supplementary adapter will contribute additional electrical characteristics to the measured data. Any use of additional adapters is noted. Product Part Number Used Adapter Part Number Adapter End Adapter End Vender Used Quantity RF36-SJ-SJ-3 PE9463 N Jack MCX Plug Pasternack RF36-RP-RP-36 PE946 N Jack MCX Jack Pasternack RF36-SP-SP-36 PE946 N Jack MCX Jack Pasternack RF36-3SP-3SP-36 PE9478 SMA Plug MMCX Jack Pasternack RF36-3RP-3RP-36 PE9478 SMA Plug MMCX Jack Pasternack RF36-5SP-5SP-35 PE93 N Jack TNC Jack Pasternack RF36-5BJ-5BJ-3 PE989 N Jack TNC Plug Pasternack RF36-6BJ-6BJ-35 NA NA NA NA RF36-7SP-7SP-33 PE935 N Jack SMB Jack Pasternack RF36-7RP-7RP-37 PE935 N Jack SMB Jack Pasternack RF36-7BJ-7BJ-36 PE936 N Jack SMB Plug Pasternack RF36-S7RP4-S7RP4-35 PE94 SMA Plug SSMB Jack Pasternack RF36-S7SP4-S7SP4-35 PE94 SMA Plug SSMB Jack Pasternack RF36-PN-PN-5 NA NA NA NA RF@samtec.com Report Revision: /8/ Page:3
6 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Product Part Number RF36-V3SJ4- V3SJ4-35 RF36-V3SP4- V3SP4-35 RF36-V3RP4- V3RP4-35 Used Adapter Part Number ADP5-6SP-V3SP; ADP5-6SJ-V3SP; ADP5-6SP-V3SJ; ADP5-6SJ-V3SJ; ADP5-6SP-V3SJ; ADP5-6SJ-V3SJ; Adapter End N Plug; N Jack; N Plug; N Jack; N Plug; N Jack; Adapter End MMCXV Plug; MMCXV Plug; MMCXV Jack; MMCXV Jack; MMCXV Jack; MMCXV Jack; Vender Samtec Samtec Samtec Used Quantity Definition of Assembly under Test: The performance characteristics include the interface with adapters. Port Designations: The connector attached to port of the VNA is End from the part number callout. is measured using S and / is measured using S. Legend for Plots: 5 samples were tested. Base on the insertion loss, the min/max plots are shown for clarity in this report. RF@samtec.com Report Revision: /8/ Page:4
7 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Results Summary RF36-SJ-SJ RF@samtec.com Report Revision: /8/ Page:5
8 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-RP-RP RF@samtec.com Report Revision: /8/ Page:6
9 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-SP-SP RF@samtec.com Report Revision: /8/ Page:7
10 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-3SP-3SP RF@samtec.com Report Revision: /8/ Page:8
11 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-3RP-3RP RF@samtec.com Report Revision: /8/ Page:9
12 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-5SP-5SP RF@samtec.com Report Revision: /8/ Page:
13 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-5BJ-5BJ RF@samtec.com Report Revision: /8/ Page:
14 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-6BJ-6BJ RF@samtec.com Report Revision: /8/ Page:
15 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-7SP-7SP RF@samtec.com Report Revision: /8/ Page:3
16 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-7RP-7RP RF@samtec.com Report Revision: /8/ Page:4
17 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-7BJ-7BJ RF@samtec.com Report Revision: /8/ Page:5
18 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-S7RP4-S7RP RF@samtec.com Report Revision: /8/ Page:6
19 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-S7SP4-S7SP RF@samtec.com Report Revision: /8/ Page:7
20 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-PN-PN RF@samtec.com Report Revision: /8/ Page:8
21 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-V3SJ4-V3SJ RF@samtec.com Report Revision: /8/ Page:9
22 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-V3SP4-V3SP RF@samtec.com Report Revision: /8/ Page:
23 Description: RF Cable Assembly, 5 Ohm, RG36 Cable RF36-V3RP4-V3RP RF@samtec.com Report Revision: /8/ Page:
24 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Instrument Setup: For some of test results, network analyzer (Agilent E57C) was used and setup as below: Network Analyzer Agilent E57C ENA Series (9 KHz GHz Range) Mechanical Calibration Kit 853F Electronic Calibration Kit Averaging Factor 4 Smoothing Off IF Bandwidth 3 Hz Sweep Start 5 MHz Sweep End 8.5 GHz Points 6 For some of test results, network analyzer (Agilent N53C) was used and setup as below: Network Analyzer Mechanical Calibration Kit Electronic Calibration Kit Agilent N53C PNA-L Series (3 KHz - GHz) 855D N4433A Averaging Factor Smoothing Off IF Bandwidth KHz Sweep Start 3 KHz Sweep End GHz Points 6 RF@samtec.com Report Revision: /8/ Page:
25 Description: RF Cable Assembly, 5 Ohm, RG36 Cable Test Fixtures: E57C (Typical set-up, actual part not depicted.) N53C (Typical set-up, actual part not depicted.) RF@samtec.com Report Revision: /8/ Page:3
RF Characterization Report
RF178 Series Cable Assemblies RF178-2SJ1-2SJ1-35 RF178-2RP1-2RP1-35 RF178-2SP1-2SP1-36 RF178-3RP1-3RP1-36 RF178-S7RP4-S7RP4-35 RF178-S7SP4-S7SP4-35 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Samtec
RF Characterization Report
SMA-J-P-H-ST-MT1 Mated with: RF316-01SP1-01BJ1-0305 Description: 50-Ω SMA Board Mount Jack, Mixed Technology Samtec, Inc. 2005 All Rights Reserved Table of Contents Introduction...1 Product Description...1
Shielding Effectiveness Comparison Report
Shielding Effectiveness Comparison Report Shielded (RF316) and Double-Shielded (RS316) Series Cable Assemblies Mates with MCX, MMCX, MMCXV, SMA, SMB5, SSMB, BNC, TNC Description: 50Ω RG316 RF Cable WWW.SAMTEC.COM
High Speed Competitive Comparison Report. Samtec MMCX-J-P-H-ST-TH1 Mated With MMCX-P-P-H-ST-TH1 Competitor A (Mated Set) Competitor B (Mated Set)
High Speed Competitive Comparison Report Samtec MMCX-J-P-H-ST-TH1 Mated With MMCX-P-P-H-ST-TH1 Competitor A (Mated Set) Competitor B (Mated Set) REVISION DATE: January 6, 2005 TABLE OF CONTENTS Introduction...
High Speed Characterization Report
High Speed Characterization Report MMCX-P-P-H-ST-TH1 mated with MMCX-J-P-H-ST-TH1 MMCX-P-P-H-ST-MT1 mated with MMCX-J-P-H-ST-MT1 MMCX-P-P-H-ST-SM1 mated with MMCX-J-P-H-ST-SM1 MMCX-P-P-H-ST-EM1 mated with
CABLE ORDERING INFORMATION How to Build Custom Cable Assemblies
p.1 CABLE ORDERING INFORMATION How to Build Custom Cable Assemblies Using our Cable Specification Chart and Connector Designation Code Chart, you can easily develop your own part numbers for custom cable
SPICE Model Validation Report
HFEM-SE High Speed Flex Data Link Mated with: QTE-xxx-01-x-D-A QSE-xxx-01-x-D-A Description: Flex Data Link, High Speed, 0.8mm Pitch New Albany IN 47151-1147 USA SIG@samtec.com Report Revision: 9/13/2007
242, , FAX.
TEL. 886 2 8994 1601, FAX. 886 2 8994 1602 sales@rfconnector.com.tw, www.rfconnector.com.tw General Information SMA SMB Subminiature Connectors Screw Lock Subminiature Connectors Snap Lock 50 Ω 18 GHz
Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification
Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification J. Ferry, C. Arroyo Copyright 2008 Samtec, Inc Page 1 Summary LIFEJACK met or exceeded TIA/EIA-568-B.2-2001 Category 5e requirements for Insertion
SMB Connectors. Adaptors-50Ω. Plug to Plug. Jack to Jack. Plug to Jack. Bulkhead Jack to Jack
SMB Connectors Adaptors-50Ω Plug to Plug 1P-801-00 Jack to Jack 1P-802-00 Plug to Jack 1P-803-00 Bulkhead Jack to Jack 1P-804-18 Mini-SMB 75Ω Straight Plug 1P75-111-00 Cable group RG316 Straight PCB Jack
Validation Report Comparison of Eye Patterns Generated By Synopsys HSPICE and the Agilent PLTS
Comparison of Eye Patterns Generated By Synopsys HSPICE and the Agilent PLTS Using: Final Inch Test/Eval Kit, Differential Pair - No Grounds Configuration, QTE-DP/QSE-DP, 5mm Stack Height (P/N FIK-QxE-04-01)
High Speed Characterization Report
QTH-030-01-L-D-A Mates with QSH-030-01-L-D-A Description: High Speed Ground Plane Header Board-to-Board, 0.5mm (.0197 ) Pitch, 5mm (.1969 ) Stack Height Samtec, Inc. 2005 All Rights Reserved Table of Contents
MULTIFLEX The flexible alternative to SEMI-RIGID
MULTIFLEX The flexible alternative to SEMI-RIGID Content Product description................................................................. 65 Features and benefits...............................................................
High Speed Characterization Report
SSW-1XX-22-X-D-VS Mates with TSM-1XX-1-X-DV-X Description: Surface Mount Terminal Strip,.1 [2.54mm] Pitch, 13.59mm (.535 ) Stack Height Samtec, Inc. 25 All Rights Reserved Table of Contents Connector Overview...
Electronic Calibration (ECal) Modules for Vector Network Analyzers
TECHNICAL OVERVIEW Electronic Calibration (ECal) Modules for Vector Network Analyzers N755xA Series, 2-port Economy ECal Module 8509xC Series, 2-port RF ECal Module N469xD Series, 2-port Microwave ECal
EXPERIMENT EM3 INTRODUCTION TO THE NETWORK ANALYZER
ECE 351 ELECTROMAGNETICS EXPERIMENT EM3 INTRODUCTION TO THE NETWORK ANALYZER OBJECTIVE: The objective to this experiment is to introduce the student to some of the capabilities of a vector network analyzer.
High Speed Cable Assemblies
High Speed Cable Assemblies Data Rate Cable Assemblies s.................................. 4-9 Data Rate Coax & Twinax Cable Assemblies DataRay High Density Cable Assemblies Custom Data Rate Cable Capabilities
Keysight MOI for USB Type-C Connectors & Cable Assemblies Compliance Tests (Type-C to Legacy Cable Assemblies)
Revision 01.01 Jan-21, 2016 Universal Serial Bus Type-C TM Specification Revision 1.1 Keysight Method of Implementation (MOI) for USB Type-C TM Connectors and Cables Assemblies Compliance Tests Using Keysight
WiFi Interface Identifier
WiFi Interface Identifier WiFi Interface Identifier Today s wireless market has exposed us to many new, and some familiar connectors. The wide range of antennas, access points, routers, WLAN s, cellular
ReversePolarity Series(SMA,BNC,TNC)
RP ReversePolarity Series(SMA,BNC,TNC) Description Reverse polarity BNC, TNC, N & SMA connectors (RP-BNC, RP-TNC, RP-SMA) are designed for uses in wireless applications where a non-standard interface has
Keysight MOI for USB Type-C Connectors & Cable Assemblies Compliance Tests (Type-C to Legacy Cable Assemblies)
Revision 01.00 Nov-24, 2015 Universal Serial Bus Type-C TM Specification Revision 1.1 Keysight Method of Implementation (MOI) for USB Type-C TM Connectors and Cables Assemblies Compliance Tests Using Keysight
EXTEND YOUR REACH. Copper Mountain Technologies USB VNAs. S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11
Copper Mountain Technologies USB VNAs S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11 to S 44 Dynamic range as high as 162 db typ. (1 Hz IF bandwidth) Measurement
4GHz / 6GHz Radiation Measurement System
4GHz / 6GHz Radiation Measurement System The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces. With a frequency
Shielding Effectiveness Report HQCD
HQCD Mates with QSH, QTH, QSH-EM Description: 0.50mm Q Strip High Speed Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Product Overview... 1 Test Overview... 1 Shielded Room
Keysight E5061B ENA Vector Network Analyzer CONFIGURATION GUIDE
Keysight E5061B ENA Vector Network Analyzer CONFIGURATION GUIDE Ordering guide The following steps will guide you through configuring your E5061B. Standard furnished item 1 Installation guide CD ROM IO
Radio ETI031 Laboratory Experiments 2: VECTOR NETWORK ANALYSER, ANTENNA and RECEIVER MEASUREMENTS
Lund University Electrical and Information Technology GJ 2007-09-30 Radio ETI031 Laboratory Experiments 2: VECTOR NETWORK ANALYSER, ANTENNA and RECEIVER MEASUREMENTS Göran Jönsson 2007 Objectives: Part
Shielding Effectiveness Report HQDP
HQDP Mates with QSH-DP, QTH-DP Description: 0.50mm 100Ω Differential 30 AWG Twinax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Product Overview... 1 Test Overview... 1 Shielded
SECTION 5 SWITCHING CONNECTORS/MOEBIUS MC-CARD/RP-MCX R199/R299 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 5 SWITCHING CONNECTORS/MOEBIUS MC-CARD/RP-MCX R199/R299 SIMPLIFICATION IS OUR INNOVATON Visit www.radiall.com for more information Contents Introduction... 5-4 to 5-5 MOEBIUS Characteristics...
SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188 Gold Plated
SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188 Gold Plated RF Connectors Technical Data Sheet PE45145 Configuration SMA Male Connector 50 Ohms Straight Body Geometry RG174, RG316, RG188
Characterizing Non-Standard Impedance Channels with 50 Ohm Instruments
Characterizing Non-Standard Impedance Channels with 50 Ohm Instruments Julian Ferry, Jim Nadolny, Craig Rapp: Samtec Inc. Mike Resso, O.J. Danzy: Agilent Technologies Introduction Emerging systems are
Electrical Performance Report 85 ohm Reference Impedance
ERM8-050-09.0-S-DV Mates with ERF8-050-07.0-S-DV Description: Edge Rate Strip Series, 0.8mm Centerline 16mm Stack Height Samtec, Inc. 2005 All Rights Reserved TABLE OF CONTENTS Connector Overview... 1
High Speed Characterization Report
PCRF-064-XXXX-EC-SMA-P-1 Mated with: PCIE-XXX-02-X-D-TH Description: PCI Express Cable Assembly, Low Loss Microwave Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly Overview...
Agilent AN Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note
Agilent AN 346-2 Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note Introduction How a balanced circuit differs from an unbalanced circuit A balanced circuit
STANDARD COAXIAL CONNECTORS. Eco 7/16 series
STANDARD COAXIAL CONNECTORS Eco 7/16 series Eco 7/16 INTRODUCTION GENERAL Standard coaxial connectors Screw on coupling Compliant to CECC and IEC standards 50 Ω APPLICATIONS Broadcast RF components (filters,
Shielding Effectiveness Report
VRDPC-050-01-S-D-RA Mates with VPDP/VPLSP/VPSTP Description: Data Rate I/O Cable Assemblies Samtec, Inc. 2005 All Rights Reserved Table of Contents Product Overview... 1 Shielded Room Noise Floor Verification...
Agilent 8762F Coaxial Switch 75 ohm
Agilent 8762F Coaxial Switch 75 ohm Technical Overview DC to 4 GHz Exceptional repeatability over 1 million cycle life Excellent isolation The 8762F brings a new standard of performance to 75 ohm coaxial
Agilent Technologies High-Definition Multimedia
Agilent Technologies High-Definition Multimedia Interface (HDMI) Cable Assembly Compliance Test Test Solution Overview Using the Agilent E5071C ENA Option TDR Last Update 013/08/1 (TH) Purpose This slide
ATM Flexible Coax Cable, Cable and Connector Specifications
ATM Flexible Coax Cable, Cable and Connector Specifications Advanced Technical Materials (ATM) manufactures high performance microwave cable that utilizes only the very best materials, incorporating proprietary
Millimeter Signal Measurements: Techniques, Solutions and Best Practices
New Network Analyzer platform Millimeter Signal Measurements: Techniques, Solutions and Best Practices Phase Noise measurements update 1 N522XA PNA Series Network Analyzer Introducing Highest Performance
Configuration of PNA-X, NVNA and X parameters
Configuration of PNA-X, NVNA and X parameters VNA 1. S-Parameter Measurements 2. Harmonic Measurements NVNA 3. X-Parameter Measurements Introducing the PNA-X 50 GHz 43.5 GHz 26.5 GHz 13.5 GHz PNA-X Agilent
TEST EQUIPMENT PLUS. Signal Hound USB-SA44B / USB-TG44A. Application Note 1: The Smith Chart. Rev. 0
Rev. 0 TEST EQUIPMENT PLUS Signal Hound USB-SA44B / USB-TG44A Application Note 1: The Smith Chart USING THE SMITH CHART Chapter 1 1 Using the Smith Chart Making Single-Frequency Vector Impedance Measurements
Keysight Technologies Electronic Calibration (ECal) Modules for Vector Network Analyzers
Keysight Technologies Electronic Calibration (ECal) Modules for Vector Network Analyzers N4690 Series, 2-port Microwave ECal 85090 Series, 2-port RF ECal N4430 Series, 4-port ECal N7550 Series, 2-port
EMC SHIELDING EFFECTIVENESS TEST REPORT : : :
1.0 1 of 16 EMC SHIELDING EFFECTIVENESS TEST REPORT Test Specification Manufacturer Test Samples : : : MIL-DTL-83528F Specialty Silicone Products 1. SSP502-40 Nickel Graphite in silicone 40 Shore A 2.
Amphenol RF- BNC Connector Series
Page 1 of 7 enter part number Products 7/16 1.0/2.3 1.6/5.6 AMC BNC / RP-BNC C FAKRA SMB FME HN MCX Mini-UHF Mini 75 Ohm SMB MMCX Precision (APC) QDS QMA QWS SC SlimLine BNC SMA / RP-SMA SMB SMC SMP TNC
EMC SHIELDING EFFECTIVENESS TEST REPORT : : :
1.0 1 of 15 EMC SHIELDING EFFECTIVENESS TEST REPORT Test Specification Manufacturer Test Samples : : : MIL-DTL-83528F Specialty Silicone Products, Inc. 1. SSP-2529 DOCUMENT HISTORY REVISION ISSUE DATE
High Speed Characterization Report
PCIEC-XXX-XXXX-EC-EM-P Mated with: PCIE-XXX-02-X-D-TH Description: 1.00 mm PCI Express Internal Cable Assembly, 30 AWG Twinax Ribbon Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable
USB 3.1 Cable-Connector Assembly Compliance Tests. Test Solution Overview Using the Keysight E5071C ENA Option TDR. Last Update 2015/02/06
USB 3.1 Cable-Connector Assembly s Test Solution Overview Using the Keysight E5071C ENA Option TDR Last Update 015/0/06 Purpose This slide will show how to make measurements of USB 3.1 cable & connector
A New Noise Parameter Measurement Method Results in More than 100x Speed Improvement and Enhanced Measurement Accuracy
MAURY MICROWAVE CORPORATION March 2013 A New Noise Parameter Measurement Method Results in More than 100x Speed Improvement and Enhanced Measurement Accuracy Gary Simpson 1, David Ballo 2, Joel Dunsmore
RF & MW Connectors. 6 Where signal & Connectivity is needed, There is GigaLane
RF & MW Connectors - 2.4 mm Connectors - 2.92 mm Connectors - Hermetic Seal (0.012 Glass Bead) - SMP Connectors - BMA Connectors - High Performance End Lanch Connectors - High Performance SMA Connectors
S14WI Splitter for Wireless Infrastructure
1 of 9 S14WI Splitter for Wireless Infrastructure Technical Product Data Features Active or Passive Options Available Optional Antenna Current Monitor and Alarm Optional Antenna DC Bias Select Pole-mount
Attenuators, Couplers and Filters
Objectives: Attenuators, Couplers and Filters To become familiar with the functionality of common RF devices. To characterize both the reflection and transmission responses of these devices. NOTE: IN CONTRAST
87415A microwave system amplifier A microwave. system amplifier A microwave system amplifier A microwave.
20 Amplifiers 83020A microwave 875A microwave 8308A microwave 8307A microwave 83006A microwave 8705C preamplifier 8705B preamplifier 83050/5A microwave The Agilent 83006/07/08/020/050/05A test s offer
Advanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Agilent 2-Port and 4-Port PNA-X Network Analyzer N5249A - 10 MHz to 8.5 GHz N5241A - 10 MHz to 13.5 GHz N5242A - 10
EMC SHIELDING EFFECTIVENESS TEST REPORT : : :
1.0 1 of 17 EMC SHIELDING EFFECTIVENESS TEST REPORT Test Specification Manufacturer Test Samples : : : MIL-DTL-83528F Specialty Silicone Products 1. SSP547-65 Silver Copper in silicone 65 shore A 2. SSP548-65
Data sheets CDN-M, CDN-AF, CDN-S, CDN-T, CDN-RJ, CDN-USB
Data sheets CDN-M, CDN-AF, CDN-S, CDN-T, CDN-J, CDN-USB Coupling and decoupling devices (CDN) for immunity tests 180906 CDN M1, M2, M3, M4, M5, M2/3 PE N C1 C2 Simplified diagram of M3 network CDN M-Types
Xeta4. Occupied Bandwidth. Measurements
Xeta4 Occupied Bandwidth Measurements 10/7/2013 Witnessed by Test conducted by Date 10/8/2013 Date 10/8/2013 Page 1 of 39 Introduction... 4 Scope... 4 Equipment Under Test (EUT)... 4 Power Input... 4 Peripheral
High Speed Characterization Report
ESCA-XX-XX-XX.XX-1-3 Mated with: SEAF8-XX-05.0-X-XX-2-K SEAM8-XX-S02.0-X-XX-2-K Description: 0.80 mm SEARAY High-Speed/High-Density Array Cable Assembly, 34 AWG Samtec, Inc. 2005 All Rights Reserved Table
Keysight Technologies PXI Vector Network Analyzer Series
Ihr Spezialist für Mess- und Prüfgeräte Keysight Technologies PXI Vector Network Analyzer Series Drive down the size of test datatec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax
Agilent Technologies PSA Series Spectrum Analyzers Test and Adjustment Software
Test System Overview Agilent Technologies PSA Series Spectrum Analyzers Test and Adjustment Software Test System Overview The Agilent Technologies test system is designed to verify the performance of the
Supplementary Information
Supplementary Information Standards Laboratory Calibration Order 1-999999999-1 Model 8481A Manufacturer Agilent Technologies Description Power Sensor, 10 MHz to 18 GHz, -30 to +20 dbm Serial 2 Options
Agilent N9923A FieldFox RF Vector Network Analyzer 2 MHz to 4/6 GHz. Data Sheet
Agilent N9923A FieldFox RF Vector Network Analyzer 2 MHz to 4/6 GHz Data Sheet Table of Contents Definitions... 2 FieldFox RF Vector Network Analyzer... 3 Cable and Antenna Analyzer (Option 305)... External
Agilent 4-Port PNA-L Network Analyzers
Agilent 4-Port PNA-L Network Analyzers N5230A Options 240, 245 300 khz to 20 GHz Speed and accuracy you can count on Integrated 4-port, balanced measurements up to 20 GHz Introducing the 4-port PNA-L network
High Speed Characterization Report
HLCD-20-XX-TD-BD-2 Mated with: LSHM-120-XX.X-X-DV-A Description: 0.50 mm Razor Beam High Speed Hermaphroditic Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly
Electrical Components Catalog RF Connectors
Introduction Product Facts Designed and Manufactured to meet MI-C-39012 Requirements Wide Range of Connectors available in 50 and 75 Ohm Impedance The range offers connectors to suit from DC-11 GHz Operation
High Speed Characterization Report
ECDP-16-XX-L1-L2-2-2 Mated with: HSEC8-125-XX-XX-DV-X-XX Description: High-Speed 85Ω Differential Edge Card Cable Assembly, 30 AWG ACCELERATE TM Twinax Cable Samtec, Inc. 2005 All Rights Reserved Table
High Speed Characterization Report
ERCD_020_XX_TTR_TED_1_D Mated with: ERF8-020-05.0-S-DV-L Description: 0.8mm Edge Rate High Speed Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly Overview... 1
5 ESSENTIAL HINTS TO IMPROVE Millimeter-wave Network Analysis
5 ESSENTIAL HINTS TO IMPROVE Millimeter-wave Network Analysis Contents 5 Essential Hints to Improve Millimeter-wave Network Analysis Ensure Accurate, Repeatable Results Go to Hint 1 > Calibrate for Better
High Frequency. ECT-CPG com shop ECT-CPG com
High Frequency HiGH FreQuenCY High Frequency or Radio Frequency (RF) coaxial probes are used for testing high speed circuits in a variety of industries including automotive, wireless communications, satellite,
APPLICATION SPECIFICATION
2.4/5GHZ ALANCE ANTENNA(34.9MM*9MM) 1.0 SCOPE This specification describes the antenna application and surrounding. The information in this document is for reference and benchmark purposes only. The user
UFL and Balanced Connectivity & Calibration Kit Overview
UFL and Balanced Connectivity & Calibration Kit Overview MegiQ BV Weegschaalstraat 3 5632 CW Eindhoven The Netherlands +31 40 291 1479 sales@megiq.com Visit our website at www.megiq.com The choice of a
Picture. Parameter Unit Minimum Typical Maximum. Fin and Ref Input Frequency Range MHz Input Power Level dbm
eatures requency Range: 3 to 300MHz Input Power: -10 to +17dBm Integrated Loop ilter Directly Interface to PS Series Directly Interface to VCO Series DC Power: 12V SMA Connector Picture is a Phase/requency
EE290C - Spring 2004 Advanced Topics in Circuit Design
EE290C - Spring 2004 Advanced Topics in Circuit Design Lecture #3 Measurements with VNA and TDR Ben Chia Tu-Th 4 5:30pm 531 Cory Agenda Relationships between time domain and frequency domain TDR Time Domain
Agilent AN Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note
Agilent AN 346-2 Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note Introduction How a balanced circuit differs from an unbalanced circuit A balanced circuit
HF860 Radio Frequency Probe
Connector type Specific HF860 order code Connecting element SMA-Female HF86002B0001G530 SMB- HF86005B0004G530 SMB-Female HF86002B0005G530 SMC- HF86005B0003G530 U.FL- HF86005B0002G530 RF- HF86005B0007G530
PXI Modules 3066 PXI Multi-Way Active RF Combiner Data Sheet
PXI Modules 3066 PXI Multi-Way Active RF Combiner Data Sheet The most important thing we build is trust 250 MHz to 6 GHz RF signal conditioning module for multi- UE, MIMO and Smartphone testing Four full
RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].
![RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].](/thumbs/90/101629325.jpg "RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].")
RP SMA Male Connector Solder Attachment for PE-SR402AL, PE-SR402FL, PE-SR402FLJ, PE- SR402TN, RG402, Gold Plated Brass Body RF Connectors Technical Data Sheet PE44724 Configuration SMA Male Reverse Polarity
RP TNC Male Connector Crimp/Solder Attachment for PE-C240, RG8X, inch, LMR-240, LMR-240-DB, LMR-240-UF, B7808A
RP TNC Male Connector Crimp/Solder Attachment for PE-C240, RG8X, 0240 inch, LMR-240, LMR-240-DB, LMR-240-UF, B7808A RF Connectors Technical Data Sheet PE44670 Configuration TNC Male Reverse Polarity Connector
Antennas: ML-5299-PTA1-01R ML-5299-WPNA1-01R ML-5299-HPA1-01R
M AP-5131 Access Point Antenna Connection Guide ML-5299-PTA1-01R ML-5299-WPNA1-01R ML-5299-HPA1-01R 2.9 db 4 db 7 db 15.5 db 25-90262-01R 2008 Motorola, Inc. All rights reserved. MOTOROLA and the Stylized
Characterization of SPDT RF Switch (Mini-circuits MSP2TA )
Characterization of SPDT RF Switch (Mini-circuits ) Raul Monsalve SESE, Arizona State University August 18, 2014 2 Description The RF switch Mini-circuits was characterized in terms of repeatability and
FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR. 2.4GHz LE MODULE MODEL NUMBER: RN4020
FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR 2.4GHz LE MODULE MODEL NUMBER: RN4020 REPORT NUMBER: 14U17191-1 ISSUE DATE: MARCH 21, 2014
How the Braid Impedance of Instrumentation Cables Impact PI and SI Measurements
How the Braid Impedance of Instrumentation Cables Impact PI and SI Measurements Istvan Novak (*), Jim Nadolny (*), Gary Biddle (*), Ethan Koether (**), Brandon Wong (*) (*) Samtec, (**) Oracle This session
AV3672 Series Vector Network Analyzer
AV3672 Series Vector Network Analyzer AV3672A/B/C/D/E (10MHz 13.5 GHz/26.5 GHz/43.5 GHz/50 GHz/67 GHz) Product Overview: AV3672 series vector network analyzer include AV3672A (10MHz 13.5GHz), AV3672B (10MHz
Test Cable Assemblies
Test Cable Assemblies DC-65 GHz 8851 SW Old Kansas Ave. Stuart, FL 34997 USA +1-772-286-9300 +1-800-544-5594 sales@emc-rflabs.com www.emc-rflabs.com Premium Test Cable Lab-Flex 200 Frequency to 31 GHz
High Data Rate Characterization Report
High Data Rate Characterization Report EQRF-020-1000-T-L-SMA-P-1 Mated with: QSE-xxx-01-x-D-A and SMA-J-P-x-ST-TH1 Description: Cable Assembly, High Speed Coax, 0.8 mm Pitch Samtec, Inc. 2005 All Rights
Physical Test Setup for Impulse Noise Testing
Physical Test Setup for Impulse Noise Testing Larry Cohen Overview Purpose: Use measurement results for the EM coupling (Campbell) clamp to determine a stable physical test setup for impulse noise testing.
Platform Migration 8510 to PNA. Graham Payne Application Engineer Agilent Technologies
Platform Migration 8510 to PNA Graham Payne Application Engineer Agilent Technologies We set the standard... 8410 8510 When we introduced the 8510, we changed the way S-parameter measurements were made!
Digital to Analog Output Module (with IF Output Capability)
ICE-D2AWG-r2 Innovative Computer Engineering Digital to Analog Output Module (with IF Output Capability) This single-site module has three modes: I/Q modulation, interpolating DAC, and tone generator.
MWA REVB LNA Measurements
1 MWA REVB LNA Measurements Hamdi Mani, Judd Bowman Abstract The MWA LNA (REVB) was measured on the Low Frequency Radio astronomy Lab using state of the art test equipment. S-parameters of the amplifier
Specification for Conducted Emission Test
1 of 10 1. EMI Receiver Frequency range 9kHz 7.0 GHz Measurement time per frequency 10 µs to 100 s time sweep, span = 0 Hz - 1 µs to 16000 s Sweep time in steps of 5 % frequency sweep, span 10 Hz - 2.5
Connectors for Telecommunications
Connectors for Telecommunications BNC Connectors H-CN03-123x H-CN03-223X H-CN03-121x H-CN03-113x H-CN03-125x H-CN03-225x Straight Crimp plugs - BNC Straight crimp sockets - BNC Straight solder plugs -
Performance evaluation of two RF power limiters based on PIN diodes
Performance evaluation of two RF power limiters based on PIN diodes Marta Bautista Durán, José A. López-Pérez December 2017 IT-CDT 2017-19 Observatorio de Yebes Apdo. 148, E-19080 Guadalajara SPAIN 1 1
Picture. Parameter Unit Minimum Typical Maximum. Fin and Ref Input Frequency Range MHz 5 25 Input Power Level dbm
eatures requency Range: 5 to 25MHz Input Power: -3 to +17dBm Integrated Loop ilter Directly Interface to PS Series Directly Interface to VCO Series DC Power: 12V SMA Connector Picture is a Phase/requency
ANN-MS. active GPS antenna. Data Sheet. locate, communicate, accelerate. Abstract
locate, communicate, accelerate ANN-MS active GPS antenna Data Sheet Abstract The ANN active GPS antenna with integrated low-noise amplifier (LNA) is the perfect match to the u-blox GPS receivers. 48 x
Option 010 adds the impedance measurement function to the 4396B. By installing this option
Product Overview Option 010 adds the impedance measurement function to the 4396B. By installing this option into the 4396B spectrum/network/impedance analyzer, you can measure impedance parameters directly.
L1 Low Noise Amplifier
Page 1 of 6 L1 Low Noise Amplifier Technical Product Data Features High Rejection Preselection Filter Excellent Gain G = 40dB Low Noise Figure F < 2.0dB Description Designed for use with a passive L1 antenna,
Quick Reference Guide RF Coaxial Connectors
Quick Reference Guide Coaxial RF Products: Quick View Product Operating Frequency (Max.) Impedance VSWR Durability (Mating Cycles) Operating Temp. Coupling Style Standard 7/16 7 GHz 50 Ω 1.02 + 0.03f up
Description RF Explorer RFEAH-25 1 is a 25mm diameter, high performance near field H-Loop antenna.
Description RF Explorer RFEAH-25 1 is a 25mm diameter, high performance near field H-Loop antenna. RFEAH-25 is a very sensitive, compact and easy to use H-loop near field antenna. The low-loss design exhibits
SMA Male Connector Crimp/Solder Attachment for RG58, RG303, RG141, PE-C195, PE-P195, LMR-195, inch
SMA Male Connector Crimp/Solder Attachment for RG58, RG303, RG141, PE-C195, PE-P195, LMR-195, 0195 inch RF Connectors Technical Data Sheet PE4215 Configuration SMA Male Connector MIL-STD-348A 50 Ohms Straight
Challenges and Solutions for Removing Fixture Effects in Multi-port Measurements
DesignCon 2008 Challenges and Solutions for Removing Fixture Effects in Multi-port Measurements Robert Schaefer, Agilent Technologies schaefer-public@agilent.com Abstract As data rates continue to rise
L1L2 Low Noise Amplifier
Page 1 of 5 L1L2 Low Noise Amplifier Technical Product Data Features High Rejection Preselection Filter Excellent Gain G = 40dB Low Noise Figure F < 2.2dB Description Designed for use with a passive L1\L2