Customized HP100 Sensors. HP300 Series. Customized to solve difficult application problems

Transcription

1 Customized HP00 Sensors HP00 Series Customized to solve difficult application problems

2 The HP00 Series: Are you faced with any of these problems? Tightly mounted thru-scan sensors interfere with each other, and a filter doesn' t help. An advance operation check is needed to prevent error due to dust or dirt. Chattering may occur during detection, depending on the target object condition. A diffuse-scan model sometimes fails to detect a target object that has a hole or notch. A diffuse-scan sensor is needed but is unreliable if the scanning distance is too short. The use of both NPN and PNP models requires too much troublesome maintenance. Seasonal fogging of the lens surface causes operational error. Cables become disconnected from sensors mounted on moving units. The HP00 Series can solve your application problems! Yamatake' s HP00 Series engineers listen to users' issues and discuss possible customized product solutions. Models listed below are now available. Type s Description Short-range diffuse-scan HP00-S HP00-S2 NPN, Preleaded2m PNP, Preleaded2m Remote emitter control thru-scan HP00-T-00 NPN, Preleaded2m Wide-beam diffuse-scan HP00-D HP00-D2 NPN, Preleaded2m PNP, Preleaded2m NPN/PNP dual output model HP00- -CN0 Preleaded connector0cm 2

3 Short-range diffuse-scan typehp00-s / HP00-S2 Twin emitter-leds and an extended sensitivity adjustment band enable reliable detection in the short-distance range Extended sensitivity adjustment band Dead zone Short-distance characteristics improved by twin LEDs Incoming light level Incoming light level Conventional model HP00-S Mutual interference prevention allows dense same-line mounting of multiple sensors APPLICATIONS Position detection based on the difference in scanning distances Even at short distances the difference in light level is sufficient to differentiate the positions. Reliable detection of low-reflectance targets Incoming light level Thanks to improved characteristics, incoming light level is high at short distances. By setting a short scanning distance, low-reflectance targets can be detected. HP00-S

4 CATALOG LISTING HP00-S Description NPN, preleaded, cable length 2m HP00-S2 PNP, preleaded, cable length 2m SPECIFICATIONS Detection type Power supply Current consumption Sensitivity adjustment method Operation mode Output type Response time Emitter LED Indicator Ambient light immunity Operating temperature Operating humidity Storage temperature Protective structure Wiring type Weight Circuit protection HP00-S HP00-S2 Short-distance diffuse-scan 0 to 0Vdc (ripple 0% max.) ma 200mm -turn potentiometer Light-ON / dark-on selectable by switch NPN open collector PNP open collector Switching current: 00mA max. (resistive load). Output dielectric strength: 0V.Voltage drop: V max. (at 00mA switching current). Short protection. 500µs max. for both operation and recovery Infrared LED : orange at control output ON. Stability indicator: green at stable light/dark status Incandescent lamp: 0,000 lux max. Sunlight: 0,000 lux max. 0 to +60 C (no freezing or condensing) 0 to 85% RH (no freezing or condensing) 0 to +70 C(no freezing or condensing) IP67 (IEC) Preleaded, cable length 2m Approx. 55g (body with 2m cable only) Power ON malfunction prevention (approx. 8ms delay), wiring error protection EXTERNAL DIMENSIONS (unit: mm) Sensitivity adjustment potentiometer Stability indicator Light-ON Dark-ON Operation mode selector switch M threaded thru-hole (2) dia. Emitter OUTPUT CIRCUIT DIAGRAM HP00-S (Note that a FET is used for output) HP00-S2 Black 0 to 0Vdc Black 0 to 0Vdc

5 Remote emitter control thru-scan type HP00 -T- 00 Long scanning distance of 5m Emitter-LED ON/OFF control by remote input Status indicator in front enables light axis alignment by only one operator APPLICATIONS Multiple sensors in a dense single line without mutual interference Mutual interference is a problem when thru-scan sensors are mounted close together. But if each emitter is turned on in succession (using emitter control input), and its output checked, mutual interference is prevented-and there is no limit on the number of units. Sequential scanning Sequential scanning Sensor diagnosis by remote input Sensor failure (due to dust, dirt, light axis displacement, etc.) can be discovered at startup by switching emit-ters ON/OFF using emitter control input. Wireless interlock signal transmission Send a permission signal from one piece of equipment to another, or a start/stop instruction to an automatic guided vehicle using a long-distance -bit wireless signal. CATALOG LISTING Description HP00-T-00 NPN, preleaded, cable length 2m 5

6 SPECIFICATIONS Detection type Power supply Current consumption Sensitivity adjustment method Operation mode Output type Emitter control input Response time Emitter LED Indicator Ambient light immunity Operating temperature Operating humidity Storage temperature Protective structure Wiring type Weight Circuit protection HP00-T-00 Thru-scan 0 to 0Vdc (ripple 0% max.) Emitter: 6mA. : ma. 5m -turn potentiometer Light-ON / dark-on selectable by switch NPN open collector Switching current: 00mA max. (resistive load). Output dielectric strength: 0V. Voltage drop: V max. (at 00mA switching current). Short protection. Emitter control input: emission OFF at 0V, normal emission with open connection 500µs max. for both operation and recovery Red LED : Orange at power ON, green at stable light-on and light-off, and red for front incoming light indicator Emitter : Orange at power ON and go emission Incandescent lamp: 0,000 lux max. Sunlight: 0,000 lux max. 0 to +60 C (no freezing or condensing) 0 to 85% RH (no freezing or condensing) 0 to +70 C (no freezing or condensing) IP67 (IEC) Preleaded, cable length 2m Approx. 55g Power ON malfunction prevention (approx. 8ms delay), wiring error protection EXTERNAL DIMENSIONS (unit: mm) Emitter Power indicator Sensitivity adjustment potentiometer Stability indicator Light-ON Dark-ON Operation mode selector switch M threaded thru-hole (2) M threaded thru-hole (2) dia dia. Emitter light axis light axis Emitter OUTPUT CIRCUIT DIAGRAM (Note that a FET is used for output) Normal emission Normal emission 0 to 0Vdc Black 0 to 0Vdc 6

7 Wide-beam diffuse-scan typehp00-dhp00-d2 Targets of various shapes can be reliably detected with a beam that is 7 times as wide as a regular diffuse-scan beam. High sensitivity makes low-reflectance targets detectable. Detection area characteristics (Targets: 5050cm, 00cm white paper) Detection area [mm] L [mm] 5050cm paper, horizontal 5050cm paper, vertical 00cm paper, horizontal 00cm paper, vertical APPLICATIONS Detecting notched or perforated PWBs 7 2

8 CATALOG LISTING HP00-D Description NPN, preleaded, cable length 2m HP00-D2 PNP, preleaded, cable length 2m SPECIFICATIONS Detection type Power supply Current consumption Sensitivity adjustment method Operation mode Output type Response time Emitter LED Indicator Ambient light immunity Operating temperature Operating humidity Storage temperature Protective structure Wiring type Weight Circuit protection HP00-D HP00-D2 Wide-beam diffuse-scan 0 to 0Vdc (ripple 0% max.) 6mA 0 to 00mm -turn potentiometer Light-ON / dark-on selectable by switch NPN open collector PNP open collector Switching current: 00mA max. (resistive load). Output dielectric strength: 0V. Voltage drop: V max. (at 00mA switching current). Short protection. 500µs max. for both operation and recovery Infrared LED : orange at control output ON. Stability indicator: green at stable light/dark status. Incandescent lamp: 0,000 lux max. Sunlight: 0,000 lux max. 0 to +60 C (no freezing or condensing) 0 to 85% RH (no freezing or condensing) 0 to +70 C (no freezing or condensing) IP67 (IEC) Preleaded, cable length 2m Approx. 55g (body with 2m cable only) Power ON malfunction prevention (approx. 8ms delay), wiring error protection EXTERNAL DIMENSIONS (unit: mm) Sensitivity adjustment potentiometer Stability indicator Light-ON Dark-ON Operation mode selector switch M threaded thru-hole (2) dia. Emitter OUTPUT CIRCUIT DIAGRAM HP00-D (Note that a FET is used for output) HP00-D2 Black 0 to 0Vdc Black 0 to 0Vdc 8 2

9 NPN-PNP dual output type HP00--CN0 HP00-T-CN (thru-scan) / HP00-P-CN0 (polarized retroreflective) / HP00-A-CN0 (diffuse-scan) Can be connected to 2 input s, with NPN output and with PNP output Output type is changeable without changing wiring, since output line is common, unlike individual output models Notes: Since this sensor may be damaged if its output is connected to output from another sensor, do not use the output in an OR. Be sure that the supply power for this sensor is the same as for the load. The sensor may be damaged if different power is applied. For details, refer to the specifications. Since this sensor does not have an output short- protection, short-ing of the output may damage the output transistor or shorten the sensor's life. APPLICATIONS CATALOG LISTING Description NPN-PNP dual output, thru-scan, preleaded connector, cable length 0cm NPN-PNP dual output, polarized retroreflective, preleaded connector, cable length 0cm NPN-PNP dual output, diffuse-scan, preleaded connector, cable length 0cm 9 2

10 SPECIFICATIONS Detection type Power Current consumption Sensitivity adjustment method Operation mode Output type Response time Emitter LED Indicator Ambient light immunity Operating temperature Operating humidity Storage temperature Protective structure Wiring type Mass Circuit protection Thru-scan HP00-E: 6mA max. HP00-R: 8mA max. 5m Polarized retroreflective 0 to 26.Vdc (ripple 0% max.) 20mA max to 5m (when used with FE-RR8 or FE-RR7reflector) -turn potentiometer Diffuse-scan 2mA max. Selectable by output selector switch (see applications on front page) NPN-PNP dual output Switching current: 0mA (resistive load) Output voltage: 26.V Voltage drop: V max. (at 0mA switching current) 500µs max. for both operation and recovery Red LED Infrared LED Incandescent lamp: 0,000 lux max. Sunlight: 0,000 lux max. 0 to +0C (no freezing or condensing) 5 to 85% RH (no freezing or condensing) 0 to +70C (no freezing or condensing) IP67 (IEC) Preleaded, cable length 0cm Approx. 55g (body only) Power ON malfunction prevention (output is fixed at high level for approx. 8ms), wiring error protection (without short- protection) m EXTERNAL DIMENSIONS (unit: mm) HP00-T-CN0 Thru-scan Emitter (HP00-E) Power indicator Sensitivity adjustment potentiometer (HP00-R) HP00-P-CN0 Polarized retroreflective HP00-A-CN0 Diffuse-scan Sensitivity adjustment potentiometer Stability indicator Light-ON Stability indicator Light-ON Dark-ON Operation selector switch Dark-ON Operation selector switch M threaded thru hole (2) M threaded thru hole (2) M threaded thru hole (2).2 dia.2 dia.2 dia Light axis or emitter Emitter Connector (common) dia... Connector Lock-ring M2x OUTPUT CIRCUIT DIAGRAM (Note that a FET is used for output) HP00-T Emitter (HP00-E) HP00-T (HP00-R), HP00-P-CN0 (polarized retroreflective), HP00-A-CN0 (diffuse-scan) Used as NPN output Used as PNP output 26.Vdc 26.Vdc 26.Vdc 0