HITACHI INVERTER SJ300 / L300P SERIES SERVICE MANUAL

Transcription

1 HITACHI INVERTER SJ300 / L300P SERIES SERVICE MANUAL After reading this manual, keep it hand for future reference. H I T A C H I NBS6CX

2 Revision History Table No. Revision Contents The Date of Issue Operation Manual No. Japanese font was removed. Nov NBS6BX 2 The specification of the capacity 75-32kW and more was added. Mar. 200 NBS6CX

3 Table of contents. Investigation of the inverter. Specification label(model name, Manufacturing number ; MFG).. Model name -..2 MFG number -.2 Inverter specification.2. SJ L300P Trouble shooting 2. INV trip contents, remedy, advice Option error 2.2. Feed-back board (SJ-FB) Digital-input option board (SJ-DG) Device-Net option board (SJ-DN) Check of the trip monitor contents Confirmation of the warning monitor contents Return to an initialization setup (Factory-shipment state) Debug mode 3. Monitor mode Function mode Parameter settings for inverter The check of control power supply voltage and a control signal 4. Control power supply voltage Control signal 4-5. Maintenance and Inspection 5. Maintenance and Inspection 5.. Daily inspection Cleaning Periodical inspection Daily and annual maintenance Megger test Withstand voltage test How to check inverter, converter, BR and Thyristor portion Parts replacement Unit replacement 5-8 Appendix Circuit Diagram Internal block diagram Structure figure

4 . Investigation of the inverter. Specification label (Model name, Manufacturing number ; MFG) There are 2 specification label attached to the inverter as shown in Fig -. Specification label Fig - Specification label location Please confirm the model name and MFG number from the specification label as follows. Model name Applicable motor Input ratings Output ratings MFG number.. Model name SJ H F (R) Fig -2 contents of specification label R : with POT meter F : with digital operator Model name L : 3 φ 200V class H : 3 φ 400V class Applicable motor (055 : 5.5kW)..2 MFG number 94 A T Serial No. (000 ~ 9999) Year of production (9 : 999) Production No. REV. No.( character or 2 characters) Production year & month (94 : 999 / April) -

5 .2 Inverter specification.2. SJ300 Monitor Mode Display code d00 d002 d003 d004 d005 d006 Function name Output frequency monitor Output current monitor Operation direction monitor PID feedback monitor Intelligent input terminal monitor Intelligent output terminal monitor SJ300 monitor or data range (digital operator) Initial data / (Hz) (A) - F(forward)/o(stop)/r(reverse) / / / / ( ) 8 FW 7 6 (Example) FW, terminal 7,2, : ON Terminal 8,6,5,4,3:OFF ON OFF AL (Example) Terminal 2,:ON AL, 5,4,3:OFF ON d007 Frequency / / / conversion monitor d02 torque monitor % - d03 Output voltage monitor V - d04 Input electric power monitor kw - Accumulated time d06 monitor during RUN / / h - d07 Power ON time monitor / / h - d080 Number of trip time monitor / ( ) (time) - d08 Trip monitor - d082 Trip monitor 2 - d083 Trip monitor 3 Trip Code, frequency(hz), current(a), - d084 Trip monitor 4 voltage(v),run time(h) power ON time(h) - d085 Trip monitor 5 - d086 Trip monitor 6 - d090 Warning monitor Warning code - F00 Output frequency 0.0, starting frequency-max. frequency setting (2 nd max. 3 rd max. frequency)(hz) 0.00 F002 st acceleration time / / (s) F202 2 nd acceleration time / / (s) F302 3 rd acceleration time / / (s) F003 st deceleration time / / (s) F203 2 nd deceleration time / / (s) F303 3 rd deceleration time / / (s) F004 Operation direction selection 00(forward)/0(reverse) 00 (Note) Change mode during run by selection of b03 (software lock selection). (Note2) Do not forget to press STR key when you change the display. OFF (Note) Note 2

6 Function Mode Base setting Analog input setting Multistage speed,jogging frequency setting Direct current braking V/f characteristic Code Function name SJ300 Setting range Initial data -FE/-FU/-F A00 Frequency setting selection 0(terminal)/02(operator)/03(RS485)/04(option)/05(option2) 0/0/02 A002 Operation setting selection 0(terminal)/02(operator)/03(RS485)/04(option)/05(option2) 0/0/02 A003 Base frequency Maximum. frequency(hz) 50./60./60. A203 Base frequency, 2nd motor 30. 2nd Maximum. frequency (Hz) 50./60./60. A303 Base frequency, 3rd motor rd Maximum. frequency (Hz) 50./60./60. A004 Maximum frequency (Hz) 50./60./60. A204 Maximum frequency, 2nd motor (Hz) 50./60./60. A304 Maximum frequency, 3rd motor (Hz) 50./60./60. A005 AT terminal selection 00( Changing of O and OI with AT terminal)/ 0(Changing of O and O2 with AT terminal) 00 A selection 00(single)/0(auxiliary speed of O, OI) [no reversible] / 02(auxiliary speed of O, OI [reversible] 00 A0 0 start / (Hz) 0.00 A02 0 end / (Hz) 0.00 A03 0 start rate (%) 0. A04 0 end rate (%) 00. A05 0 start selection 00 (external starting frequency)/0(0hz) 0 A06 O, OI, O2 sampling.-30.(times) 8. A09 Multi-speed selection 00(binary : range is to 6 stage speed with 4 terminals)/ 0(bit : range is to 8 stage speed with 7 terminals) 00 A020 Multi-speed , starting frequency-maximum. frequency(hz) 0.00 A220 Multi-speed 0, 2 nd motor 0.00, starting frequency-2 nd maximum frequency(hz) 0.00 A320 Multi-speed 0, 3 rd motor 0.00, starting frequency-3 rd maximum frequency(hz) 0.00 A02 Multi-speed 0.00, starting frequency-maximum frequency(hz) 0.00 A022 Multi-speed2 0.00, starting frequency-maximum frequency(hz) 0.00 A023 Multi-speed3 0.00, starting frequency-maximum frequency(hz) 0.00 A024 Multi-speed4 0.00, starting frequency-maximum frequency(hz) 0.00 A025 Multi-speed5 0.00, starting frequency-maximum frequency(hz) 0.00 A026 Multi-speed6 0.00, starting frequency-maximum frequency(hz) 0.00 A027 Multi-speed7 0.00, starting frequency-maximum frequency(hz) 0.00 A028 Multi-speed8 0.00, starting frequency-maximum frequency(hz) 0.00 A029 Multi-speed9 0.00, starting frequency-maximum frequency(hz) 0.00 A030 Multi-speed0 0.00, starting frequency-maximum frequency(hz) 0.00 A03 Multi-speed 0.00, starting frequency-maximum frequency(hz) 0.00 A032 Multi-speed2 0.00, starting frequency-maximum frequency(hz) 0.00 A033 Multi-speed3 0.00, starting frequency-maximum frequency(hz) 0.00 A034 Multi-speed4 0.00, starting frequency-maximum frequency(hz) 0.00 A035 Multi-speed5 0.00, starting frequency-maximum frequency(hz) 0.00 A038 Jogging frequency 0.00, starting frequency-9.99(hz).00 A039 Jogging selection 00(free-run on JG stop / invalid on running) / 0(stop decelerating on JG stop / invalid on running) / 02(DC braking on JG stop/invalid on running) / 03(free-run on JG stop/valid on running[jg after stop 00 decelerating]) / 04 (stop decelerating on JG stop/valid on running) / 05 (DC braking on JG stop/valid on operating) A04 Torque boost selection 00 (manual torque boost) / 0 (automatic torque boost) 00 A24 Torque boost selection, 2 nd motor 00 (manual torque boost) / 0 (automatic torque boost) 00 A042 Manual torque boost (%).0 A242 Manual torque boost, 2 nd motor (%).0 A342 Manual torque boost, 3 rd motor (%).0 A043 Manual torque boost point (%) 5.0 A243 Manual torque boost point, 2 nd motor (%) 5.0 A343 Manual torque boost point, 3 rd motor (%) 5.0 A044 st control 00/(VC)/0(VP.7power)/02(free V/f setting)/03(slv)/ 04(0Hz-SLV)/05(V2) 00 A244 2 nd control 00/(VC)/0(VP.7power)/02(free V/f setting) /03(SLV)/04(0Hz-SLV) 00 A344 3 rd control 00/(VC)/0(VP.7power) 00 A045 Output voltage gain A05 DC braking selection 00(invalid)/0(valid) 00 A052 DC braking frequency (Hz) 0.50 A053 DC braking wait time (s) 0.0 A054 DC braking power (%) <0.-80.(%)> 0. A055 DC braking time (s) 0.0 A056 DC braking edge/level selection 00(edge action)/0(level action) 0 A057 DC braking power (starting time) (%) <0.-80.(%)> 0. A058 DC braking time(starting time) (s) 0.0 A059 DC carrier frequency 0.5-5(kHz) Derating <0.5-0kHz> 5.0<3.0> (Note) < > indicate the setting range of 75 to 50kW Note - 3

7 Upper and lower limiter,jump frequency PID control AVR Operation mode/ adjustable function External frequency adjustment Accel, Decel Instantaneous power failure restart Function Mode Initial data Code Function name SJ300 Setting range -FE/-FU/-F A06 st frequency maximum limiter 0.00, st frequency lower limitter - maximum frequency(hz) 0.00 A26 2 nd frequency maximum limiter 0.00, 2 nd frequency lower limiter-2 nd setting maximum frequency(hz) 0.00 A062 st frequency minimum limiter 0.00, start frequency-maximum frequency(hz) 0.00 A262 2 nd frequency minimum limiter 0.00, start frequency-2 nd setting maximum frequency(hz) 0.00 A063 Jump frequency / (Hz) 0.00 A0 Jump frequency Width (Hz) 0.50 A065 Jump frequency / (Hz) 0.00 A066 Jump frequency Width (Hz) 0.50 A067 Jump frequency / (Hz) 0.00 A068 Jump frequency Width (Hz) 0.50 A069 Acceleration stop frequency / (Hz) 0.00 A070 Acceleration stop time (s) 0.0 A07 PID selection 00(invalid)/0(valid) 00 A072 PID-P gain A073 PID-I gain (s).0 A074 PID-D gain (s) 0.00 A075 PID scale (%).00 A076 PID feedback selection 00(feedback : OI)/0(feedback : O) 00 A08 AVR selection 00(ON always)/0(off always)/02(off on decelerating) 00/00/02 (230/400)/ A082 Motor voltage selection 200/25/220/230/240, 380/400/45/440/460/480 (230/460)/ (200/400) A085 Operation mode selection 00(normal operation)/0(energy-saving operation)/02(fuzzy) 00 A086 Energy-saving responseaccuracy adjustment A092 Acceleration time / / (s) 5.00 A292 Acceleration time2(2 nd motor) / / (s) 5.00 A392 Acceleration time2(3 rd motor) / / (s) 5.00 A093 Deceleration time / / (s) 5.00 A293 Deceleration time2(2 nd motor) / / (s) 5.00 A393 Deceleration time2(3 rd motor) / / (s) 5.00 A094 2 nd stage adjustable selection 00(change with 2CH terminal)/0(change with setting) 00 A294 2 nd stage adjustable selection(2 nd motor) 00(change with 2CH terminal)/0(change with setting) 00 A095 2 nd acceleration frequency / (Hz) 0.00 A295 2 nd acceleration frequency(2 nd motor) / (Hz) 0.00 A096 2 nd deceleration frequency / (Hz) 0.00 A296 2 nd deceleration frequency (2 nd motor) / (Hz) 0.00 A097 Acceleration pattern selection 00(straight line)/0(s-curve)/02(u-curve)/03(reverse U-curve) 00 A098 Deceleration pattern selection 00(straight line)/0(s-curve)/02(u-curve)/03(reverse U-curve) 00 A0 OI start / (Hz) 0.00 A02 OI end / (Hz) 0.00 A03 OI start rate (%) 20. A04 OI end rate (%) 00. A05 OI start selection 00(external start frequency)/0(0hz) 0 A O2 start / / (Hz) 0.00 A2 O2 end / / (Hz) 0.00 A3 O2 start rate (%) -00. A4 O2 end rate (%) 00. A3 Acceleration curve constant 0(small swelling)-0(large swelling) 02 A32 Deceleration curve constant 0(small swelling-0(large swelling) 02 b00 Retry selection 00(trip)/0(0Hz start)/02(start after equal frequency)/ 03(trip after equaling frequency and deceleration stop) 00 b002 Allowable under-voltage power failure time (s).0 b003 Retry wait time (s).0 b004 Instantaneous power failure/ 00(invalid/0(valid)/02(invalid during stop and deceleration by stop under-voltage trip during stop command) 00 b005 Instantaneous power failure/ under-voltage retry time 00(6 times)/0(free) 00 selection b006 Open-phase selection 00(invalid)/0(valid) 00 b007 Frequency setting to match / (Hz) 0.00 Note - 4

8 Electronic thermal Intelligent input terminal setting Free V/f setting Overload limit Function mode Code Function name SJ300 Setting range b02 Electronic thermal level 0.2*constant current-.20*constant current(a) b22 b32 b03 b23 b33 b05 b06 b07 b08 b09 b020 b02 Electronic thermal level (2 nd motor) Electronic thermal level (3 rd motor) st electronic thermal characteristic selection 2 nd electronic thermal characteristic selection 3 rd electronic thermal characteristic selection Free electronic thermal frequency Free electronic thermal current Free electronic thermal frequency 2 Free electronic thermal current 2 Free electronic thermal frequency 3 Free electronic thermal current 3 Overload restriction selection 0.2*constant current-.20*constant current(a) 0.2*constant current-.20*constant current(a) 00(reduced characteristic)/ 0(constant torque characteristic)/ 02(free setting) 00(reduced characteristic)/ 0(constant torque characteristic)/ 02(free setting) 00/(reduced characteristic)0(constant torque characteristic)/ 02(free setting) Initial data -FE/-FU/-F Rated Current of inverter Rated Current of Inverter Rated current of inverter 0/0/00 0/0/00 0/0/ (Hz) (A) (Hz) (A) (Hz) (A) (invalid)/0(enabled on acceleration / constant speed)/ 02(enabled on constant speed)/03(enabled on acceleration / constant speed (speed increasing at regenerating mode)) b022 Overload restriction level 0.50* rated current-2.00* rated current(a) <-.80*ratede current(a)> b023 b024 Overload restriction limit constant Overload restriction 2 selection 0 Rated current of Inverter x (s).00 00(invalid)/0(enabled on acceleration / constant speed)/ 02(enabled on constant speed)/03(enabled on acceleration / constant speed (speed increasing at regenerating mode)) b025 Overload restriction level *rated current-2.00*rated current(a) <-.80*rated current(a)> b026 b03 Overload restriction constant 2 Software lock mode selection 0 Rated current of inverter x (s).00 00(impossible to change the data except this item when SFT terminal is ON)/0(impossible to change the data except setting frequency item when SFT terminal is ON)/02(impossible to change the data except this item)/ 03(impossible to change the data except setting frequency item)/ 0(possible to change data on operating) b00 Free V/f frequency 0.- Free V/f frequency2(hz) 0. b0 Free V/f voltage (V) 0.0 b02 Free V/f frequency Free V/f frequency3(hz) 0. b03 Free V/f voltage (V) 0.0 b04 Free V/f frequency Free V/f frequency4(hz) 0. b05 Free V/f voltage (V) 0.0 b06 Free V/f frequency Free V/f frequency5(hz) 0. b07 Free V/f voltage (V) 0.0 b08 Free V/f frequency Free V/f frequency6(hz) 0. b09 Free V/f voltage (V) 0.0 b0 Free V/f frequency Free V/f frequency7(hz) 0. b Free V/f voltage (V) 0.0 b2 Free V/f frequency (Hz) 0. b3 Free V/f voltage (V) 0.0 0/(RV:Reverse is valid)/02(cf:multi-speed)/ 03(CF2:Multi-speed2)/ C00 Intelligent input setting 04(CF3:Multi-speed3)/ 05(CF4:Multi-speed4)/ 06(JG:Jogging)/ 8 07( DB:External DC braking)/ 08(SET:2 nd control)/ C002 Intelligent input 2 setting 09(2CH:two-stage adjustable speed)/ ( FRS:Free-run)/ 2( EXT:External trip)/ 6 3( USP:Unattended start protection)/ 4(CS:commercial change)/ 5(SFT:software lock)/ 6(AT:Analog input voltage/current select)/ C003 Intelligent input 3 setting 7(SET3:3 rd control)/ 8(RS:Reset inverter)/ 20(STA:3wire run)/ 06 2(STP:3wire keep)/ 22(F/R:3wire forward/reverse)/ 23(PID:PID selection valid/invalid)/ 24(PIDC:PID integrating reset)/ C004 Intelligent input 4 setting 26( CAS:Control gain switch function)/ 27( UP:Remote control UP function)/ 28( DWN:Remote control DOWN function)/29( UDC:Remote control data clear)/ 3( OPE:Operating by operator select)/ 32(SF:Multi-speed bit)/ C005 Intelligent input 5 setting 33(SF2:Multi-speed bit2)/ 34(SF3:Multi-speed bit3)/ 35(SF4:Multi-speed bit4)/ 09 36(SF5:Multi speed bit5)/ 37(SF6:Multi-speed bit6)/ 38(SF7:Multi-speed bit7)/ C006 Intelligent input 6 setting 39( OLR:Overload restriction change) / 40(TL:Torque limit select)/ 03/3/03 4(TRQ:Torque limit switch )/ 42(TRQ2:Torque limit switch 2)/ C007 Intelligent input 7 setting 43((PPI:P/PI switch)/ 44(BOK:Braking comformation)/ 45( ORT:Orientation)/ 02 C008 Intelligent input 8 setting 46(LAC:LAD cancel)/ 47(PCLR:Position error clear)/ 48(STAT:Permission of pulse train)/ no(no:no assign) 0 (Note) < > indicate the setting range of 75 to 50kW 0 Note - 5

9 Input terminal setting intelligent Communication Output terminal state Analog meter setting function adjustment setting,output level setting Intelligent output terminal setting Function mode Code Function name SJ300 Setting range Initial data -FE/-FU/-F C0 Intelligent input a/b (NO/NC) selection 00(NO)/0(NC) 00 C02 Intelligent input 2 a/b (NO/NC) selection 00(NO)/0(NC) 00 C03 Intelligent input 3 a/b (NO/NC) selection 00(NO)/0(NC) 00 C04 Intelligent input 4 a/b (NO/NC) selection 00(NO)/0(NC) 00 C05 Intelligent input 5 a/b (NO/NC) selection 00(NO)/0(NC) 00 C06 Intelligent input 6 a/b (NO/NC) selection 00(NO)/0(NC) 00/0/00 C07 Intelligent input 7a/b (NO/NC) selection 00(NO)/0(NC) 00 C08 Intelligent input 8 a/b (NO/NC) selection 00(NO)/0(NC) 00 C09 Input FW a/b (NO/NC) Selection 00(NO)/0(NC) 00 00(RUN:running)/0(FA:Frequency arrival type signal)/ C02 Intelligent output setting 02(FA2:over setting frequency)/03( OL:Overload advance notice signal)/ 0 C022 Intelligent output 2 setting 04( OD:Output deviation for PID control)/05( AL:Alarm signal)/ 06(FA3:Only setting frequency)/07( OTQ:Over-torque signal)/ 08( IP:On instantaneous stop)/09(uv:under voltage)/ 00 C023 Intelligent output 3 setting 0(TRQ:Torque limit)/(rnt:run time over/2(ont:on time over)/ 3(THM:thermal caution)/9(brk:brake release signal)/ 03 C024 Intelligent output 4 setting 20( BER:Brake error signal)/2(zs:zero speed detect signal)/ 22(DSE:Speed error over signal)/23(pok:positioning completion signal) 07 C025 Intelligent output 5 setting 24(FA4:Over frequency 2 signal)/25(fa5:only setting frequency)/ 26(OL2: Overload advance notice signal 2) 08 C026 Alarm relay output (Intelligent output terminal -3 or -4 becomes AC0-AC2 or AC0-AC3 (Can:Alarm cord output) forcibly when alarm cord output is selected in 05 C062) C027 FM selection 00(Output frequency)/0(output current) /02(Output torque)/ 03(Digital output frequency)/04(output voltage)/ 00 05(Input electric power)/06(thermal load rate)/07(lad frequency) C028 AM selection 00(Output frequency)/0(output current)/02(output torque)/ 04(Output voltage)/05(input electric power)/06(thermal load rate)/ 00 07(LAD frequency) C029 AMI selection 00(Output frequency)/0(output current)/02(output torque)/ 04(Output voltage)/05(input electric power)/ 00 06(Thermal load rate)/07(lad frequency) C03 Intelligent output a/b 00(NO)/0(NC) 00 C032 Intelligent output 2 a/b 00(NO)/0(NC) 00 C033 Intelligent output 3 a/b 00(NO)/0(NC) 00 C034 Intelligent output 4 a/b 00(NO)/0(NC) 00 C035 Intelligent output 5 a/b 00(NO)/0(NC) 00 C036 Alarm relay output a/b 00(NO)/0(NC) 0 C040 Overload advance notice signal output mode 00(On accel. And decel, constant speed)/0(only constant speed) 0 C04 Overload advance notice Inverter *rated current(a) level rated current C042 Frequency arrival setting for acceleration / (Hz) 0.00 C043 Arrival frequency setting for deceleration / (Hz) 0.00 C044 PID deviation setting level (%) 3.0 C045 Frequency arrival setting for acceleration / (Hz) 0.00 C046 Arrival frequency setting for deceleration / (Hz) 0.00 C055 Over torque level setting (Forward-driving) (%) <0.-80.> 00. C056 Over torque level setting (Reverse-regenerating) (%) 00. C057 Over torque level setting (Reverse-driving) (%) <0.-80.> 00. C058 Over torque level setting (Forward-regenerating) (%) <0.-80.> 00. C06 Thermal warning level setting (%) <0.-80.> 80. C062 Alarm code selection 00(Invalid)/0(3bit)/02(4bit) 00 C063 Zero speed detection level setting /00.(Hz) 0.00 C070 Data command 02(operator)/03(RS485)/04(option)/05(option2) 02 C07 Communicating transmission 02(loop-back test) speed 03(2400bps)/04(4800bps)/05(9600bps)/06(9200bps) 04 C072 Communication code C073 Communication bit 7(7bit)/8(8bit) 7 C074 Communication parity 00(no parity name)/0(even parity)/02(odd parity) 00 C075 Communication stop bit (bit)/2(bit) C078 Communication waiting time (ms) 0. C08 O adjustment / ( ) Setting on forwarding C082 OI adjustment / ( ) Setting on forwarding C083 O2 adjustment / ( ) Setting on forwarding C085 Thermistor adjustment C086 AM offset adjustment (V) 0.0 C087 AMI adjustment C088 AMI offset adjustment ( ma) 4.0 (Note) < > indicate the setting range of 75 to 50kW Note - 6

10 The others Function mode Code Function name SJ300 Setting range Initial data -FE/-FU/-F b034 RUN time/power ON time level / ( )hr 0. b035 Operation direction restrict 00(Reverse is valid)/0(only forward)/02(only reverse) 00 b036 Start reduced voltage 00(Start reduced voltage time small)-06(start reduced voltage time large) 06 b037 Display selection 00(all display)/0(each function display)/02(user setting / main setting) 00 b040 Torque limit mode selection 00(4 quadrant mode)/0(terminal operation)/ 02(Analog input)/03(option)/04(option2) 00 b04 Torque limit level setting (Forward-driving at (%)/no(Invalid) <0.-80.(%)/no(Invalid)> quadrant mode) b042 Torque limit level 2 setting (Reverse-regenerating at (%)/no(Invalid) <0.-80.(%)/no(Invalid)> quadrant mode) b043 Torque limit level 3 setting (Reverse-driving at (%)/no(Invalid) <0.-80.(%)/no(Invalid)> quadrant mode) b044 Torque limit level 4 setting (Forward-regenerating at (%)/no(Invalid) <0.-80.(%)/no(Invalid)> quadrant mode) b045 Torque LAD-STOP selection 00(Invalid)/0(Valid) 00 b046 Reverse run prevention selection 00(Invalid)/0(Valid) 00 Selection of non-stop b050 function at instantaneous power failure 00(Invalid)/0(Valid) 00 b05 Start voltage of non-stop function setting (V) 0.0 b052 OV LAD-STOP level of nonstop function setting (V) 0.0 b053 Deceleration time of nonstop function setting / / (s).00 b054 Deceleration frequency width of non-stop function setting (Hz) 0.00 b080 AM adjustment b08 FM adjustment b082 Start frequency adjustment (Hz) 0.50 b083 Carrier frequency setting (kHz) Derating enable, <0-0kHz> 5.0 <3.0> b084 Initialize mode 00(Trip history clear)/0(data initialization)/ 02(Trip history clear + data initialization) 00 b085 Country code for initialization 00(Interior)/0(EC)/02(USA) 0/02/00 b086 Frequency scalar conversion factor b087 STOP key enable 00(valid)/0(invalid) 00 b088 Resume on FRS cancellation mode 00(0Hz start)/0(start f-equaling) 00 b090 BRD usage ratio (%) 0.0 b09 Stop mode selection 00(deceleration stop)/0(free-run stop) 00 b092 Cooling fan control 00(Always ON)/ 0(ON during run, After power ON, then for 5 minutes on stop is implied.) 00 b095 BRD selection 00(invalid)/0(valid<invalid during stop>)/02(valid<valid during stop>) 00 b096 BRD ON level / (V) 360/720 b098 Thermistor selection 00(invalid)/0(Positive temperature coefficient enable)/02 (NTC enable) 00 b099 Thermistor error level (ohm) b20 Braking control selection 00(Invalid)/0(valid) 00 b2 Waiting time for releasing braking conformation (s) 0.00 b22 Waiting time for acceleration (s) 0.00 b23 Waiting time for stop (s) 0.00 b24 Waiting time for signal conformation (s) 0.00 b25 Releasing frequency / (Hz) 0.00 b26 Releasing current 0.00*rated current-2.00*rated current(a) Rated current of inverter C09 Debug mode selection 00(No display)/0(display) 00 C0 UP/DWN selection 00(No frequency data)/0(keep frequency data) 00 C02 Reset selection 00(Trip cancel during ON)/0(Trip cancel during OFF)/ 02(Valid only during trip<cancel during ON>) 00 C03 Reset f frequency matching selection 00(0Hz start)/0(start f-equaling) 00 C Overload advance notice level *rated current(a) C2 O zero adjustment / ( ) C22 OI zero adjustment / ( ) C23 O2 zero adjustment / ( ) (Note) < > indicate the setting range of 75 to 50kW Inverter rated current Set on forwarding Set on forwarding Set on forwarding Note - 7

11 The others Function mode Code Function name SJ300 Setting range Initial data -FE/-FU/-F H00 Autotuning selection 00(Invalid)/0(Valid(the motor does not rotate))/ 02( Valid(the motor rotates)) 00 H002 st motor constant selection 00(Hitachi general purpose motor data)/0(autotuning data)/ 02( Autotuning data with online autotuning) 00 H202 2 nd motor constant selection 00(Hitachi general purpose motor data)/0(autotuning data)/ 02( Autotuning data with online autotuning) 00 H003 st allowable motor selection (kW) <0.2-60(kW)> Set on forwarding H203 2 nd allowable motor selection (kW) <0.2-60(kW)> Set on forwarding H004 st motor pole selection 2/4/6/8(pole) 4 H204 2 nd motor pole selection 2/4/6/8(pole) 4 H005 st speed response setting / H205 2 nd speed response setting / H006 st stabilized factor H206 2 nd stabilized factor H306 3 rd stabilized factor H020 st Set on motor constant R / (ohm) forwarding H220 2 nd Set on motor constant R / (ohm) forwarding H02 st Set on motor constant R / (ohm) forwarding H22 2 nd Set on motor constant R / (ohm) forwarding H022 st Set on motor constant L / ( mh) forwarding H222 2 nd Set on motor constant L / ( mh) forwarding H023 st Set on motor constant I / (A) forwarding H223 2 nd Set on motor constant I / (A) forwarding H024 st motor constant J / / ( kgm 2 Set on ) forwarding H224 2 nd motor constant J / / ( kgm 2 Set on ) forwarding H030 st motor constant R Set on / (ohm) (Autotuning data) forwarding H230 2 nd motor constant R Set on / (ohm) (Autotuning data) forwarding H03 st motor constant R2 Set on / (ohm) (Autotuning data) forwarding H23 2 nd motor constant R2 Set on / (ohm) (Autotuning data) forwarding H032 st motor constant L Set on / ( mh) (Autotuning data) forwarding H232 2 nd motor constant L Set on / ( mh) (Autotuning data) forwarding H033 st motor constant I 0 Set on / (A) (Autotuning data) forwarding H233 2 nd motor constant I0 Set on / (A) (Autotuning data) forwarding H034 st motor constant J / / ( kgm 2 Set on ) forwarding H234 2 nd motor constant J / / ( kgm 2 Set on ) forwarding H050 st PI-control proportion gain setting / /000.(%) 00.0 H250 2 nd PI-control proportion gain setting / /000.(%) 00.0 H05 st PI-control integration gain setting / /000.(%) 00.0 H25 2 nd PI-control integration gain setting / /000.(%) 00.0 H052 st P-control proportion gain setting H252 2 nd P-control proportion gain setting H060 st 0Hz-SLV limiter setting (%) 00. H260 2 nd 0Hz-SLV limiter setting (%) 00. H070 PI-control proportion gain for switching / /000.(%) 00.0 H07 PI-control integration gain for switching / /000.(%) 00.0 H072 P-control proportion gain for switching (Note) < > indicate the setting range of 75 to 50kW Note - 8

12 User selection Option Function mode Code Function name SJ300 Setting range Initial data -FE/-FU/-F P00 Option operation selection on error 00(TRP)/0(RUN) 00 P002 Option2 operation selection on error 00(TRP)/0(RUN) 00 P00 Feed-back option selection 00(Invalid)/0(Valid) 00 P0 Encoder pulse number setting / ( ) (pulse) 024 P02 Control mode selection 00(ASR mode)/0(apr mode) 00 P03 Pulse train input mode selection 00(Mode 0)/0(Mode )/02(Mode 2)/03(Mode 3) 00 P04 Orientation stop position setting P05 Orientation speed setting / (Hz) 5.00 P06 Orientation direction selection 00(Forward)/0(Reverse) 00 P07 Orientation completion range setting /000(0000) (pulse) 5 P08 Orientation completion delay time setting (s) 0.00 P09 Electronic gear position selection 00(Feedback)/0(Reference) 00 P020 Electronic gear numerator of ratio setting P02 Electronic gear denominator of ratio setting P022 Position control feed-forward gain setting / P023 Position control loop gain setting / P025 Compensation of secondary resistor selection 00(Invalid)/0(Valid) 00 P026 Over-speed detect level setting / (%) 35.0 P027 Speed-error over detect level setting / (Hz) 7.50 P03 Digital input option input mode selection (Acc/Dec) 00(operator)/0(option)/02(option2) 00 Stop position setting for P032 orientation input mode 00(operator)/0(option)/02(option2) 00 selection P044 DeviceNet running order of monitoring timer setting s.00 P045 Setting in action of abnormal 00(trip)/0(trip after deceleration stop)/02(invalid)/ communication 03(free-run)04(deceleration stop) 0. P046 Output assemble instance Number setting 20,2,00 2 P047 Input assemble instance Number setting 70,7,0 7 P048 Detect of idol mode for 00(trip)/0(trip after deceleration stop)/02(invalid)/ motion setting 03(free-run)04(deceleration stop) 0 P049 Pole setting of rotation speed 0-38(even only) 0 U00 User selection no/d00-p049 <-P032> no U002 User2 selection no/d00-p049 <-P032> no U003 User3 selection no/d00-p049 <-P032> no U004 User4 selection no/d00-p049 <-P032> no U005 User5 selection no/d00-p049 <-P032> no U006 User6 selection no/d00-p049 <-P032> no U007 User7 selection no/d00-p049 <-P032> no U008 User8 selection no/d00-p049 <-P032> no U009 User9 selection no/d00-p049 <-P032> no U00 User0 selection no/d00-p049 <-P032> no U0 User selection no/d00-p049 <-P032> no U02 User2 selection no/d00-p049 <-P032> no Note (Note ) P044-P049 are displayed on a kW model. - 9

13 .2.2 L300P Monitor code Display code d00 d002 d003 d004 d005 d006 Function name Output frequency monitor Output current monitor Operation direction monitor PID feedback monitor Intelligent input terminal monitor Intelligent output terminal monitor L300P monitor or data range (digital operator) Initial data / (Hz) (A) - F(forward)/o(stop)/r(reverse) / / / / ( ) FW (Example) FW, terminal2, and : ON Terminal 5, 4, 3 :OFF ON d007 Frequency / / / conversion monitor d03 Output voltage monitor V - d04 Electric power monitor kw - d06 Accumulated time monitor during RUN / / h - d07 Power ON time monitor / / h - d080 Number of trip time monitor / ( ) (time) - d08 Trip monitor Trip Code, frequency(hz), current(a), voltage(v),run time(h) power ON time(h) - d082 Trip monitor 2 Trip Code, frequency(hz), current(a), voltage(v),run time(h) power ON time(h) - d083 Trip monitor 3 Trip Code, frequency(hz), current(a), voltage(v),run time(h) power ON time(h) - d084 Trip monitor 4 Trip Code, frequency(hz), current(a), voltage(v),run time(h) power ON time(h) - d085 Trip monitor 5 Trip Code, frequency(hz), current(a), voltage(v),run time(h) power ON time(h) - d086 Trip monitor 6 Trip Code, frequency(hz), current(a), voltage(v),run time(h) power ON time(h) - d090 Warning monitor Warning code - F00 Output frequency 0.0, starting frequency-max. frequency setting (2 nd max. frequency)(hz) 0.00 F002 st acceleration time / / (s) F202 2 nd acceleration time / / (s) F003 st deceleration time / / (s) F203 2 nd deceleration time / / (s) F004 Operation direction selection 00(forward)/0(reverse) 00 (Note) Change mode during run by selection of b03 (software lock selection). (Note2) Do not forget to press STR key when you change the display. AL OFF (Example) Terminal2, :ON AL :OFF ON 2 OFF Note -0

14 Function Mode Base setting Direct current braking V/f characteristic Multistage speed,jogging frequency setting Analog input setting Code Function name L300P Setting range A00 Frequency setting selection 00(VR)/0(terminal)/02(operator)/03(RS485)/ 04(option)/05(option2) Initial data -FE/-FU/-FR 0/0/00 A002 Operation setting selection 0(terminal)/02(operator)/03(RS485)/04(option)/05(option2) 0/0/02 A003 Base frequency Maximum. frequency(hz) 50./60./60. A203 Base frequency, 2nd motor nd Maximum. frequency (Hz) 50./60./60. A004 Maximum frequency (Hz) 50./60./60. A204 A005 A006 Maximum frequency, 2nd motor AT terminal selection 02 selection (Hz) 50./60./60. 00( Changing of O and OI with AT terminal)/0(changing of O and O2 with AT terminal) 00(single)/0(auxiliary speed of O, OI) [no reversible] /02(auxiliary speed of O, OI [reversible] A0 0 start / (Hz) 0.00 A02 0 end / (Hz) 0.00 A03 0 start rate (%) 0. A04 0 end rate (%) 00. A05 0 start selection 00 (external starting frequency)/0( OHz) 0 A06 O, OI, O2 sampling.-30.(times) 8. A09 Multi-speed selection 00(binary : range is to 6 stage speed with 4 terminals)/0(bit : range is to 6 stage speed with 5 terminals) A020 Multi-speed , starting frequency-maximum. frequency(hz) 0.00 A220 Multi-speed 0, 2 nd motor 0.00, starting frequency-2 nd maximum frequency(hz) 0.00 A02 Multi-speed 0.00, starting frequency-maximum frequency(hz) 0.00 A022 Multi-speed2 0.00, starting frequency-maximum frequency(hz) 0.00 A023 Multi-speed3 0.00, starting frequency-maximum frequency(hz) 0.00 A024 Multi-speed4 0.00, starting frequency-maximum frequency(hz) 0.00 A025 Multi-speed5 0.00, starting frequency-maximum frequency(hz) 0.00 A026 Multi-speed6 0.00, starting frequency-maximum frequency(hz) 0.00 A027 Multi-speed7 0.00, starting frequency-maximum frequency(hz) 0.00 A028 Multi-speed8 0.00, starting frequency-maximum frequency(hz) 0.00 A029 Multi-speed9 0.00, starting frequency-maximum frequency(hz) 0.00 A030 Multi-speed0 0.00, starting frequency-maximum frequency(hz) 0.00 A03 Multi-speed 0.00, starting frequency-maximum frequency(hz) 0.00 A032 Multi-speed2 0.00, starting frequency-maximum frequency(hz) 0.00 A033 Multi-speed3 0.00, starting frequency-maximum frequency(hz) 0.00 A034 Multi-speed4 0.00, starting frequency-maximum frequency(hz) 0.00 A035 Multi-speed5 0.00, starting frequency-maximum frequency(hz) 0.00 A038 Jogging frequency 0.00, starting frequency-9.99(hz).00 A039 Jogging selection 00(free-run on JG stop / invalid on running) / 0(stop decelerating on JG stop / invalid on running) / 02(DC braking on JG stop/invalid on running) / 03(free-run on JG stop/valid on running[jg after stop decelerating]) / 04 (stop decelerating on JG stop/valid on running) / 05 (DC braking on JG stop/valid on operating) A04 Torque boost selection 00 (manual torque boost) / 0 (automatic torque boost) 00 A24 Torque boost selection, 2 nd motor 00 (manual torque boost) / 0 (automatic torque boost) 00 A042 Manual torque boost (%).0 A242 Manual torque boost, 2 nd motor (%).0 A043 Manual torque boost point (%) 5.0 A243 Manual torque boost point, 2 nd motor (%) 5.0 A044 st control 00/(VC)/0(VP.7power)/02(free V/f setting) 00 A244 2 nd control 00/(VC)/0(VP.7power)/02(free V/f setting) 00 A045 Output voltage gain (%) 00. A05 DC braking selection 00(invalid)/0(valid) 00 A052 DC braking frequency (Hz) 0.50 A053 DC braking wait time (s) 0.0 A054 DC braking power (%) 0. A055 DC braking time (s) 0.0 A056 A057 A058 DC braking edge/level selection DC braking power (starting time) DC braking time (starting time) 00(edge action)/0(level action) (%) (s) 0.0 A059 DC carrier frequency 0.5-2(kHz) Derating <0.5-8(kHz)> 3.0 (Note) < > indicate the setting range of 90 to 32kW N o t e -

15 Upper and lower limiter / jump frequency PID control AVR Operation mode/ adjustable function External frequency adjustment Accel Decel Instantaneous power failure restart Electronic thermal Function Mode Code Function name L300P Setting range Initial data -FE/-FU/-FR A06 st frequency upper limiter 0.00, st frequency lower limiter-maximum frequency(hz) 0.00 A26 2 nd frequency upper limiter 0.00, 2 nd frequency lower limiter-2 nd setting maximum frequency(hz) 0.00 A062 st frequency lower limiter 0.00, start frequency-maximum frequency(hz) 0.00 A262 2 nd frequency lower limiter 0.00, start frequency-2 nd setting maximum frequency(hz) 0.00 A063 Jump frequency / (Hz) 0.00 A0 Jump frequency Width (Hz) 0.50 A065 Jump frequency / (Hz) 0.00 A066 Jump frequency Width (Hz) 0.50 A067 Jump frequency / (Hz) 0.00 A068 Jump frequency Width (Hz) 0.50 A069 Acceleration stop frequency / (Hz) 0.00 A070 Acceleration stop time (s) 0.0 A07 PID selection 00(invalid)/0(valid) 00 A072 PID-P gain A073 PID-I gain (s).0 A074 PID-D gain (s) 0.00 A075 PID scale A076 PID feedback selection 00(feedback : OI)/0(feedback : O) 00 A08 AVR selection 00(ON always)/0(off always)/02(off on decelerating) 00/00/02 A082 Motor voltage selection 200/25/220/230/240, 380/400/45/440/460/480 (230/400) (230/460) (200/400) A085 Operation mode selection 00(normal operation)/0(energy-saving operation) 00 A086 Energy-saving responseaccuracy adjustment A092 Acceleration time / / (s) 5.00 A292 2 nd acceleration time / / (s) 5.00 A093 Deceleration time / / (s) 5.00 A293 2 nd deceleration time / / (s) 5.00 A094 2 nd stage adjustable selection 00(change with 2CH terminal)/0(change with setting) 00 A294 2 nd stage adjustable 00(change with 2CH terminal)/0(change with setting) 00 selection(2 nd motor) A095 2 nd acceleration frequency / (Hz) 0.00 A295 2 nd acceleration / (Hz) 0.00 frequency(2 nd motor) A096 2 nd deceleration frequency / (Hz) 0.00 A296 2 nd deceleration frequency / (Hz) 0.00 (2 nd motor) A097 Acceleration pattern selection 00(straight line)/0(s-curve)/02(u-curve)/03(reverse U-curve) 00 A098 Deceleration pattern selection 00(straight line)/0(s-curve)/02(u-curve)/03(reverse U-curve) 00 A0 OI start / (Hz) 0.00 A02 OI end / (Hz) 0.00 A03 OI start rate ( %) 20. A04 OI end rate ( %) 00. A05 OI start selection 00(external start frequency)/0(0hz) 0 A O2 start / / (Hz) 0.00 A2 O2 end / / (Hz) 0.00 A3 O2 start rate (%) -00. A4 O2 end rate (%) 00. A3 Acceleration curve constant 0(small swelling)-0(large swelling) 02 A32 Deceleration curve constant 0(small swelling-0(large swelling) 02 b00 Retry selection 00(trip)/0(0Hz start)/02(start after equal frequency)/ 03(trip after equaling frequency and deceleration stop) 00 b002 Allowable under-voltage power failure time (s).0 b003 Retry wait time (s).0 b004 Instantaneous powerfailure/under-voltage trip 00(invalid/0(valid)/ 02(invalid during stop and deceleration by stop command) during stop 00 Instantaneous powerfailure/under-voltage b005 00(6 times)/0(free) 00 retry time selection b006 Open-phase selection 00(invalid)/0(valid) 00 b007 Frequency setting to match / (Hz) 0.00 b02 Electronic thermal level 0.2*constant current-.20*constant current(a) Rated Current of inverter b22 b03 b23 b05 b06 b07 b08 b09 b020 Electronic thermal level (2 nd motor) Electronic thermal characteristic selection Electronic thermal characteristic selection (2 nd motor) Free electronic thermal frequency Free electronic thermal current Free electronic thermal frequency 2 Free electronic thermal current 2 Free electronic thermal frequency 3 Free electronic thermal current 3 0.2*constant current-.20*constant current(a) 00/(reduced characteristic)0(constant torque characteristic)/ 02(free setting) 00/(reduced characteristic)0(constant torque characteristic)/ 02(free setting) Rated Current of inverter 0/0/00 0/0/ (Hz) (A) (Hz) (A) (Hz) (A) 0.0 N o t e - 2

16 Overload limit Lock Free V/f setting Intelligent input terminal setting Input terminal setting intelligent Output terminal state setting, Intelligent output terminal setting Output level setting Function Mode Code Function name L300P Setting range b02 Overload restriction selection 00(invalid)/0(enabled on acceleration / constant speed)/02(enabled on constant speed) b022 Overload restriction level 0.50* rated current-.50* rated current(a) b023 b024 Overload restriction limit constant Overload restriction 2 selection Initial data -FE/-FU/-FR 0 Rated current of inverter x (s).00 00(invalid)/0(valid on acceleration / constant speed)/02(valid on constant speed) b025 Overload restriction level *rated current-.50*rated current(a) b026 b03 Overload restriction constant 2 Software lock mode selection 0 Rated current of inverter x (s).00 00(impossible to change the data except this item when SFT terminal is ON)/0(impossible to change the data except setting frequency item when SFT terminal is ON)/02(impossible to change the data except this item)/03(impossible to change the data except setting frequency item)/0(possible to change data on operating) b00 Free V/f frequency 0.- Free V/f frequency2(hz) 0. b0 Free V/f voltage (V) 0.0 b02 Free V/f frequency Free V/f frequency3(hz) 0. b03 Free V/f voltage (V) 0.0 b04 Free V/f frequency Free V/f frequency4(hz) 0. b05 Free V/f voltage (V) 0.0 b06 Free V/f frequency Free V/f frequency5(hz) 0. b07 Free V/f voltage (V) 0.0 b08 Free V/f frequency Free V/f frequency6(hz) 0. b09 Free V/f voltage (V) 0.0 b0 Free V/f frequency Free V/f frequency7(hz) 0. b Free V/f voltage (V) 0.0 b2 Free V/f frequency (Hz) 0. b3 Free V/f voltage (V) 0.0 C00 Intelligent input setting 0/(RV:Reverse is valid)/02(cf:multi-speed)/ 03(CF2:Multi-speed2)/ 04(CF3:Multi-speed3)/ 05(CF4:Multi-speed4)/ 06(JG:Jogging)/ 8 C002 Intelligent input 2 setting 07(DB:External DC braking)/08(set:2 nd control)/ 09(2CH:two-stage adjustable speed)/(frs:free-run)/ 2(EXT:External trip)/3(usp:unattended start protection)/ 4(CS:commercial change)/5(sft:software lock)/ 6 C003 Intelligent input 3 setting 6(AT:Analog input voltage/current select)/8(rs:reset inverter)/ 20(STA:3wire run)/ 2(STP:3wire keep)/22(f/r:3wire forward/reverse)/ 23(PID:PID selection valid/invalid)/24(pidc:pid integrating reset)/ 03/3/03 C004 Intelligent input 4 setting 27(UP:Remote control UP function)/ 28(DWN:Remote control DOWN function)/ 29(UDC:Remote control data clear)/3(ope:force operate ope)/ 32(SF:Multi-speed bit)/ 02 C005 Intelligent input 5 setting 33(SF2:Multi-speed bit2)/34(sf3:multi-speed bit3)/ 35(SF4:Multi-speed bit4)/36(sf5:multi speed bit5)/ 37(SF6:Multi-speed bit6)/38(sf7:multi-speed bit7)/ 39(OLR:Overload restriction change)/no(no:no assign) 0 C0 Intelligent input a/b (NO/NC) selection 00(NO)/0(NC) 00 C02 Intelligent input2 a/b (NO/NC) selection 00(NO)/0(NC) 00 C03 Intelligent input3 a/b (NO/NC) selection 00(NO)/0(NC) 00/0/00 C04 Intelligent input4 a/b (NO/NC) selection 00(NO)/0(NC) 00 C05 Intelligent input5 a/b (NO/NC) selection 00(NO)/0(NC) 00 C09 Input FW a/b (NO/NC) Selection 00(NO)/0(NC) 00 C02 Intelligent output setting 00(RUN:running)/0(FA:Frequency arrivaltype signal)/ 02(FA2:frequency arrival type2 signal)/03(ol:overload advance 0 C022 Intelligent output 2 setting notice signal)/04(od:output deviation for PID control)/05(al:alarm 00 C026 Alarm relay output signal)/06(fa3:only setting frequency)/08(ip:on instantaneous stop/ 09(UV:Under voltage)/(rnt:run time over)/2(ont:on time 05 C027 FM selection over)/ 3(THM:thermal 00(Output frequency)/0(output caution) current) / 03(Digital output frequency)/04(output voltage)/ 05(Input electric power)/06(thermal load rate)/07(lad frequency) 00 C028 AM selection 00(Output frequency)/0(output current)/04(output voltage)/ 05(Input electric power)/06(thermal load rate)/07(lad frequency) 00 C029 AMI selection 00(Output frequency)/0(output current)/04(output voltage)/ 05(Input electric power)/06(thermal load rate)/07(lad frequency) 00 C03 Intelligent output a/b 00(NO)/0(NC) 00 C032 Intelligent output 2 a/b 00(NO)/0(NC) 00 C036 Alarm relay output a/b 00(NO)/0(NC) 0 C040 Overload advance notice signal output mode 00(On accel. And decel, constant speed)/0(only constant speed) 0 C04 Overload advance notice *rated current(a) Inverter level rated current C042 Frequency arrival setting for acceleration / (Hz) 0.00 C043 Arrival frequency setting for deceleration / (Hz) 0.00 C044 PID deviation setting level (%) N o t e - 3

17 Communication function Analog meter setting The others Function Mode Code Function name L300P Setting range Initial data -FE/-FU/-FR C070 Data command 02(operator)/03(RS485)/04(option)/05(option2) 02 C07 Communicating 02(loop-back test)/03(2400bps)/04(4800bps)/ transmission speed 05(9600bps)/06(9200bps) 04 C072 Communication code C073 Communication bit 7(7bit)/8(8bit) 7 C074 Communication parity 00(no parity name)/0(even parity)/02(odd parity) 00 C075 Communication stop bit (bit)/2(bit) C078 Communication waiting time (ms) 0. Setting on C08 O adjustment / ( ) forwarding Setting on C082 OI adjustment / ( ) forwarding Setting on C083 O2 adjustment / ( ) forwarding C085 Thermistor adjustment C086 AM offset adjustment (V) 0.0 C087 AMI adjustment C088 AMI offset adjustment ( ma) 4.0 RUN time/power ON time b034 level / ( )hr 0. b035 Operation direction restrict 00(Reverse is valid)/0(only forward)/02(only reverse) 00 b036 Start reduced voltage 00(Start reduced voltage time small) -06(Start reduced voltage time large) 06 b037 Display selection 00(all display)/0(each function display)/ 02(User setting / main setting) 00 b080 AM adjustment b08 FM adjustment b082 Start frequency adjustment (Hz) 0.50 b083 Carrier frequency setting (kHz) Derating enable, < kHz> 3.0 b084 Initialize mode 00(Trip history clear)/0(data initialization)/ 02(Trip history clear + data initialization) 00 b085 Country code for initialization 00(Interior)/0(EC)/02(USA) 0/02/00 b086 Frequency scalar conversion factor b087 STOP key enable 00(valid)/0(invalid) 00 b088 Resume on FRS cancellation mode 00(0Hz start)/0(start f-equaling) 00 b090 BRD usage ratio (%) 0.0 b09 Stop mode selection 00(deceleration stop)/0(free-run stop) 00 b092 Cooling fan control 00(Always ON)/0(ON during run, After power ON, then for 5 minutes on stop is implied.) 00 b095 BRD selection 00(invalid)/0(valid<invalid during stop>)/ 02(valid<valid during stop>) 00 b096 BRD ON level / (V) 360/720 b098 Thermistor selection 00(invalid)/0(Positive temperature coefficient enable)/ 02 (NTC enable) 00 b099 Thermistor error level ( ohm) C06 Thermal warning level ( %) 80 C09 Debug mode selection 00(No display)/0(display) 00 C0 UP/DWN selection 00(No frequency data)/0(keep frequency data) 00 C02 Reset selection 00(Trip cancel during ON)/0(Trip cancel during OFF)/ 02(Valid only during trip<cancel during ON>) 00 C03 Reset f frequency matching selection 00(0Hz start)/0(start f-equaling) 00 Set on C2 O zero adjustment / ( ) forwarding Set on C22 OI zero adjustment / ( ) forwarding Set on C23 O2 zero adjustment / ( ) forwarding H003 st allowable motor Set on (kW) < (kW)> selection forwarding H203 2 nd allowable motor Set on (kW) < (kW)> selection forwarding H004 st motor pole selection 2/4/6/8(pole) 4 H204 2 nd motor pole selection 2/4/6/8(pole) 4 H006 st stabilized factor H206 2 nd stabilized factor P00 Option operation selection on error 00(TRP)/0(RUN) 00 P002 Option2 operation selection on error 00(TRP)/0(RUN) 00 P03 Digital input option input mode selection(acc/dec) 00(operation)/0(option)/02(option2) 00 P044 DeviceNet running order of monitoring timer setting s.00 P045 Setting in action of 00(trip)/0(trip after deceleration stop)/02(invalid)/ abnormal communication 03(free-run)04(deceleration stop) 0. P046 Output assemble instance Number setting 20,2,00 2 P047 Input assemble instance Number setting 70,7,0 7 P048 Detect of idol mode for 00(trip)/0(trip after deceleration stop)/02(invalid)/ motion setting 03(free-run)04(deceleration stop) 0 P049 Pole setting of rotation speed 0-38(even only) 0 (Note) < > indicate the setting range of 90 to 32kW (Note)P044-P049 are displayed on a kW model. N o t e - 4