Guide to CMP-28/32 Simbeor Kit
|
|
- Isabel Harrell
- 5 years ago
- Views:
Transcription
1 Guide to CMP-28/32 Simbeor Kit CMP-28 Rev. 4, Sept Simbeor , Aug. 10, 2014 Simbeor : Easy-to-Use, Efficient and Cost-Effective Electromagnetic Software
2 Introduction Design of PCB and packaging interconnects for data links running at bitrates Gbps and beyond is a challenging problem: It requires electromagnetic analysis over extremely broad frequency bandwidth from DC to GHz No frequency-continuous dielectric models available from manufactures No conductor roughness models available from manufacturers Boards are not manufactured as designed large variations and manipulations by manufacturers Making accurate measurements over this bandwidth is difficult How to design interconnects and have acceptable analysis to measurement correlation from DC up to GHz systematically? Systematic validation or benchmarking process is the key: Making sure that interconnect analysis software is accurate, measurements done properly and board is manufactured as designed CMP-28/32 channel modeling platforms is designed to illustrate and facilitate systematic analysis to measurement validation process 2
3 Simbeor Kit for CMP-28/32 CMP-28/32 Channel Modeling Platform was developed by Wild River Technology to promote systematic approach to interconnect analysis to measurement validation up to 40/50 GHz or up to 28/32 Gbps It contains 27 micro-strip and strip-line interconnect structures equipped with 2.92 mm (CMP-28) and 2.4 mm (CMP- 32) connectors and can be used to validate signal integrity simulators or measurement technique Simbeor electromagnetic signal integrity software from Simberian Inc. was used to design the platform and is used here to illustrate all elements of the analysis to measurement validation 3
4 Materials and stackup Stackup confirmed by board manufacturer Material models confirmed and identified in Simbeor (see the material identification section) 4
5 CMP-28 Simbeor Kit folders Identification and validation of material models with singleended and differential line segments Validation for microstrip single-ended structures Validation for microstrip differential structures Validation for strip single-ended and differential structures Measured data in Touchstone format and optionally board design (brd or ODB++ files available with CMP platform only) Synthesis of connector model from measured data Supplemental docs from board manufacturer (available with CMP platform only) Touchstone models created in Simbeor solutions for re-use 5
6 Microstrip (MS) single-ended (SE) planar structures TOP red BOTTOM green Just 2 layers are visible in Simbeor Board Analyzer Solution: 3_MicrostripSingle(1) 7) MS SE Multi-Z (J31-J32) 5) MS SE whiskers (J67-J68) 1) MS SE 2-inch segment (J1-J2) 2) MS SE 8-inch segment (J3-J4) 6) MS SE Multi-Z (J29-J30) 3) MS SE Beatty 25 Ohm resonator (J25-J26) 4) MS SE stub resonator (J21-J22) 6
7 Microstrip (MS) single-ended (SE) structures with discontinuities in reference conductor TOP red BOTTOM green Just 2 layers are shown in Simbeor Board Analyzer 10) MS SE with inductive via (J15-J16) 12) MS SE with 2 capacitive vias (J65-J66) 8) MS SE with voids in GND plane (J74-J75) 9) MS SE with graduate coplanar section (J69-J70) 11) MS SE with capacitive via (J19-J20) Solution: 4_MicrostripSingle(2) 7
8 Microstrip (MS) differential (DF) structures TOP red BOTTOM green Just 2 layers are shown in Simbeor Board Analyzer 13) MS DF 2-inch segment (J33- J34-J37-J38) 14) MS DF 6-inch segment (J41- J42-J45-J46) Solution: 5_MicrostripDifferential(1) 8
9 Microstrip (MS) differential (DF) structures TOP red BOTTOM green Just 2 layers are shown in Simbeor Board Analyzer 15) MS DF segment with void in GND plane (J55- J56-J59-J60) Solution: 6_MicrostripDifferential(2) 16) MS DF segment with vias (J49-J50- J51-J52) 9
10 Microstrip (MS) differential (DF) structures TOP red BOTTOM green Just 2 layers are shown in Simbeor Board Analyzer 17) MS DF X-talk (J53-J54-J57-J58- J61-J64-J71-J72) Solution: 7_MicrostripDifferentialXTalk(3) 10
11 Strip line (SL) single-ended (SE) and differential (DF) structures SIGNAL_3 blue SIGNAL_6 light blue Just 2 layers are shown in Simbeor Board Analyzer Solutions 8_StripSingle(1) 20) SL SE Beatty 25 Ohm (J27-J28) 18) SL SE 2-inch segment (J15-J16) 21) SL SE stub resonator (J23-J24) 19) SL SE 8-inch segment (J17-J18) 11
12 Strip line (SL) single-ended (SE) and differential (DF) structures SIGNAL_3 blue SIGNAL_6 light blue Just 2 layers are shown in Simbeor Board Analyzer Solution: 9_StripSingle(2) 23) SL SE with back-drilled via (J13-J14) 22) SL SE with capacitive via (J17-J18) 25) SL SE 2-inch segment inductive launch (J9-J10) 24) SL SE 2-inch segment capacitive launch (J11-J12) 12
13 Strip line (SL) single-ended (SE) and differential (DF) structures SIGNAL_3 blue SIGNAL_6 light blue Just 2 layers are shown in Simbeor Board Analyzer Solution: 10_StripDifferential(1) 26) SL DF 2-inch segment (J15-J16) 27) SL DF 6-inch segment (J15-J16) 13
14 Analysis to measurement validation steps 1. Use VNA to measure S-parameters and validate quality of the measurements 2. Get board geometry adjustments (stackup and trace widths) from manufacturer (if any) and use consistently in the material identification and the analysis (use crosssectioning if no data provided) 3. Identify broad-band dielectric and conductor roughness models with GMS-parameters 4. Simulate all structures with the identified or validated material models and confirmed adjustments consistently and compare with the measurements (no further manipulations with data) 14
15 Step 1: Preliminary measurement quality estimation for single-ended structures Folder:..\CMP-28_Simbeor_Kit_Rev4\CMP- 28_Rev4\Touchstone_Files\1stcal_single_ended PASSED! 15
16 Step 1: Preliminary measurement quality estimation for differential and via structures Folders:..\CMP- 28_Simbeor_Kit_Rev4\ CMP- 28_Rev4\ Touchstone_Files\ 2ndcal_differential and 3rdcal_vias_2sided PASSED! 16
17 Step 1: Final quality estimation with rational compact model (RCM) Select all files in TA and push Build RCM button on the Model Conversion and Quality Estimation Tools panel (RCM options Extrapolate to infinity and Extract Delay and Auto-adjust are OFF) PASSED! Quality estimation is just an example all Touchstone models in Simbeor Solutions have pre-built RCM models used for TD analysis and validation! See how to do it in demo-videos #2011_01 and 2011_02 at 17
18 Step 1: Final quality estimation with rational compact model (RCM) Select all files in TA and push Build RCM button on the Model Conversion and Quality Estimation Tools panel (RCM options Extrapolate to infinity and Extract Delay and Auto-adjust are OFF) PASSED! Quality estimation is just an example all Touchstone models in Simbeor Solutions have pre-built RCM models used for TD analysis and validation! See how to do it in demo-videos #2011_01 and 2011_02 at 18
19 Step 2: Board geometry adjustments Stackup is adjusted from data provided by manufacturer Single-ended width adjustments before analysis in Simbeor Board Analyzer (to match the impedance observed on TDR): Micro-strip single-ended line widths are adjusted from 14.5 to 13.5 mil Strip line single-ended widths are adjusted from 11.0 to 10.5 mil All other widths and dimensions are exactly as in the board design (may need consistent adjustments as follows from the validation) 19
20 Step 3: Identify material models Generalized Modal S-parameters (GMS-parameters) is the best way to identify broadband material models (patented by Simberian) Use TDR to verify identities of the launches and t-lines Use Phase Delay of GM transmission to identify/confirm dielectric constant Use GM Insertion Loss to identify/confirm loss tangent and roughness Use data from manufactured (Isola FR408HR and Taiyo solder mask) as the starting point to identify dielectric models Use 2 and 8 inch strip line segments to validate FR408HR model and identify Modified Hammerstad conductor roughness model (Solution 1_MaterialIdentification) Use 2 and 8 inch micro-strip line segments to confirm FR408HR model and validate and identify Modified Hammerstad conductor roughness model for TOP/BOTTOM layers (1_MaterialIdentification) Use 2 and 6 inch differential strip and microstrip line segments to confirm/correct material models (2_MaterialValidationDifferential) See App Notes #2014_02 and 2014_03 for details on identification with GMS-parameters at 20
21 Step 3: Dielectric and conductor roughness model identification with strip line Solution: 1_MaterialIdentification; Simbeor SFS solver; Measured (stars) GM Insertion Loss Model (circles) GM Phase Delay GM - Generalized Modal (reflection-less); About 35 GHz useful bandwidth from the measured data due to mechanical differences; Models are usable up to 50 GHz! GMS parameters computed from S-parameters measured for 2 and 8 inch strip line segments (red and blue lines) and modeled for 6 inch strip line segment (brown and green lines): FR408HR model: Wideband Debye, Dk=3.815 (3.66), 1 GHz; Conductor roughness model: Modified Hammerstad, SR=0.4 um, RF=2; 21
22 Step 3: Dielectric and conductor roughness model identification with micro-strip line Solution: 1_MaterialIdentification; Simbeor 3DML solver; Measured (stars) GM - Generalized Modal (reflection-less); GM Insertion Loss Model (circles) GM Phase Delay Models are usable up to 50 GHz! GMS parameters computed from S-parameters measured for 2 and 8 inch micro-strip line segments (red and blue lines) and modeled for 6 inch micro-strip line segment (brown and green lines): FR408HR model: Wideband Debye, Dk=3.815 (3.66), 1 GHz (same as for strip); Taiyo solder mask model: Wideband Debye, Dk=3.85 (3.9), 1 GHz; Conductor roughness model: Modified Hammerstad, SR=0.4 um, RF=3.5; 22
23 Step 3: Dielectric and conductor roughness model identification with differential strip line GM Insertion Loss GM Phase Delay Measured (stars) Model (circles) Solution: 2_MaterialIdentification Differential; Simbeor SFS solver; GM - Generalized Modal (reflection-less); Odd modes: red, blue, brown and green lines; Even modes: orange, light blue and green lines; Even modes less then 1 ps/inch difference in phase delay; GMS parameters computed from S-parameters measured for 2 and 6 inch differential strip line segments (lines with stars) and modeled for 4 inch diff. strip line segment (lines with circles): FR408HR model: Wideband Debye, Dk=3.78 (3.66), 1 GHz optionally strip layer can be filled with resin with smaller Dk to have modes propagate with different speed; Conductor roughness model: Modified Hammerstad, SR=0.4 um, RF=2; 23
24 Step 3: Dielectric and conductor roughness model identification with micro-strip line Solution: 2_MaterialIdentification Differential; Simbeor 3DML solver; GM Insertion Loss GM Phase Delay (even) GM Phase Delay (odd) Measured: lines with stars Model: lines with circles GM - Generalized Modal (reflection-less); Odd modes: red, brown, blue and green lines; Even modes: orange, light blue and green lines; Even mode - about 1 ps/inch difference in phase delay; GMS parameters computed from S-parameters measured for 2 and 6 inch micro-strip line segments (red and blue lines) and modeled for 4 inch micro-strip line segment (brown and green lines): FR408HR model: Wideband Debye, Dk=3.815 (3.66), 1 GHz (same as for strip); Taiyo solder mask model: Wideband Debye, Dk=3.85 (3.9), 1 GHz; Conductor roughness model: Modified Hammerstad, SR=0.4 um, RF=3.5; 24
25 Step 4: Simulate all 27 structures and compare with the measurements Synthesize model for 2.92 mm connector with 2.4 mm adapter from measured S-parameters Compute and compare S-parameters for all structures (complete adapter-to-adapter links) Compare simulated and measured magnitudes and phase/group delays in terminal and mixed-mode space up to 50 GHz Compute TDR from simulated and measured S-parameters and compare for all structures Use rational compact models and Gaussian step with 20 ps 10-90% rise time Compute eye diagrams for 28 Gbps PRBS signals from simulated and measured S-parameters and compare for selected structures See demo-videos #2013_01 and 2013_02 to see how to do post-layout analysis with geometry adjustments in Simbeor Board analyzer 25
26 Synthesis of connector model Connector model is synthesized from S-parameters measured for two pairs of mm adapter and 2.92 mm connectors connected back-to-back The model is constructed by matching measured magnitude and phase of transmission and reflection parameters to model composed with 4 coaxial line segments: See details in Solution ConnectorModel; Model S-parameters are saved to connector_2p92_kt.s2p file in ModelsToReUse for further use; TDR from S-parameters Measured: dash lines; Model: solid brown line 26
27 1) 2-inch microstrip line segment Board Analyzer: Trace width is adjusted (14.5 to 13.5 mil); 2 discontinuity selector for the launches (identical); See also notes on next slide and in the solution; MS SE 2-inch segment (J1-J2) Solution: 3_MicrostipSingle(1) Measured: cmp28_mstrp_2in_p1j1_p2j2.s2p Selector/Project/Circuit: MS_SE_2in_J1_J2 27
28 1) 2-inch microstrip line segment: De-compositional analysis Board Analyzer: 2 discontinuity selectors with coaxial ports Trace width is adjusted in BA Simbeor 3DML (with HF dispersion) Auto-extraction Connector + adapter model (added) Connector + Launch are also simulated separately in PCB/MS_ConnectorAndLaunch for further reuse Launch model Simbeor 3DML Connector + adapter model (added) See also solution notes for MS SE 2-inch segment 28
29 1) 2-inch microstrip line segment: Magnitude of S-parameters Reflection Transmission Measured: lines with stars Model: lines with circles MS Launch looses the localization at about 30 GHz: Distance from signal via to stitching vias is about quarter of wavelength at 30 GHz we cannot expect correlation above that frequency! Though, the impedance of the return path remains low due to plenty of stitching vias. 29
30 1) 2-inch microstrip line segment: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 30
31 1) 2-inch microstrip line segment: TDR with 20 ps Gaussian step Model (blue) Measured (red and orange) Variations of impedance along the traces visible here indicates that either trace width is varying or dielectric is inhomogeneous (or both); This is not accounted for in the model and explains differences in the reflection. 31
32 1) 2-inch microstrip line segment: 28 Gbps PRBS, 25 ps rise/fall time Measured (blue) Eyes are on top of each other! Model (green) 32
33 2) 8-inch microstrip line segment MS SE 8-inch segment (J3-J4) Solution: 3_MicrostipSingle(1) Measured: cmp28_mstrp_8in_p1j4_p2j3.s2p Selector/Project/Circuit: MS_SE_8in_J4_J3 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; See also notes in the solution; 33
34 2) 8-inch microstrip line segment: Magnitude of S-parameters Transmission Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width and dielectric properties explains differences in reflection losses; 34
35 2) 8-inch microstrip line segment: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 35
36 2) 8-inch microstrip line segment: TDR with 20 ps Gaussian step Model (blue) Measured (red and orange) 36
37 2) 8-inch microstrip line segment: 28 Gbps PRBS, 25 ps rise/fall time Measured blue; Model green; Eyes are on top of each other! 37
38 3) Microstrip 25-Ohm Beatty standard MS SE Beatty 25-Ohm (J25-J26) Solution: 3_MicrostipSingle(1) Measured: cmp28_beatty_25ohm_p1j25_p2j26.s2p Selector/Project/Circuit: MS_SE_Beatty_25Ohm_J25_J26 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional 2 discontinuity selectors added for steps (identical); See also notes in the solution; 38
39 3) Microstrip 25-Ohm Beatty standard: Magnitude of S-parameters Transmission Reflection Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 39
40 3) Microstrip 25-Ohm Beatty standard: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 40
41 3) Microstrip 25-Ohm Beatty standard: TDR with 20 ps Gaussian step Measured (red and orange) Impedance of the wider section is off (no adjustments); Model (blue) 41
42 4) Microstrip stub resonator MS SE Resonator (J21-J22) Solution: 3_MicrostipSingle(1) Measured: cmp28_resonator_p1j21_p2j22.s2p Selector/Project/Circuit: MS_SE_Resonator_J21_J22 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional discontinuity selector is added for X-junction and 2 discontinuity selectors added for open ends (identical); See also notes in the solution; 42
43 4) Microstrip stub resonator: Magnitude of S-parameters Transmission Reflection Measured: lines with stars Model: lines with circles 43
44 4) Microstrip stub resonator: Transmission phase and group delay Group Delay Measured: lines with stars Model: lines with circles Phase Delay 44
45 4) Microstrip stub resonator: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue) 45
46 5) Microstrip whiskers (short stubs) MS SE Whiskers (J67-J68) Solution: 3_MicrostipSingle(1) Measured: cmp28_whiskers_p1j68_p2j67.s2p Selector/Project/Circuit: MS_SE_Whiskers_J68_J67 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to reuse PCB/MS_ConnectorAndLaunch model; Additional discontinuity selectors are added for each pair of whiskers (identical); See also notes in the solution; 46
47 5) Microstrip whiskers: Magnitude of S-parameters Reflection Transmission Discrepancies above GHz Substantial differences in insertion and reflection loss above GHz; See notes for TDR; Measured: lines with stars Model: lines with circles 47
48 5) Microstrip whiskers: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 48
49 5) Microstrip whiskers : TDR with 20 ps Gaussian step Measured (red and orange) TRACES ON THE BOARD ARE NOT UNIFORM it explains the differences above GHz Model (blue and green) 49
50 6) Microstrip multi-z link 1 MS SE Multi-Z (J29-J30) Solution: 3_MicrostipSingle(1) Measured: cmp28_multiz_p1j30_p2j29.s2p Selector/Project/Circuit: MS_SE_MultiZ_J30_J29 Board Analyzer: Only 14.5 mil trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional discontinuity selectors are added for all steps; See also notes in the solution; 50
51 6) Microstrip multi-z link 1: Magnitude of S-parameters Transmission Variation of trace width and dielectric properties explains differences in reflection losses; Reflection Measured: lines with stars Model: lines with circles 51
52 6) Microstrip multi-z link 1: Transmission phase and group delay Group Delay Measured: lines with stars Model: lines with circles Phase Delay 52
53 6) Microstrip multi-z link 1: TDR with 20 ps Gaussian step Measured (red and orange) About 10% difference in wider lines; About 5% in narrow lines; No width adjustments in wider and narrower strips; Model (blue and green) 53
54 7) Microstrip multi-z link 2 MS SE Multi-Z (J31-J32) Solution: 3_MicrostipSingle(1) Measured: cmp28_multiz_p1j31_p2j32.s2p Selector/Project/Circuit: MS_SE_MultiZ_J31_J32 Board Analyzer: Only 14.5 mil trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional discontinuity selectors are added for all steps; See also notes in the solution; 54
55 7) Microstrip multi-z link 2: Magnitude of S-parameters Transmission Variation of trace width and dielectric properties explains differences in reflection losses; Reflection Measured: lines with stars Model: lines with circles 55
56 7) Microstrip multi-z link 2: Transmission phase and group delay Group Delay Measured: lines with stars Model: lines with circles Phase Delay 56
57 7) Microstrip multi-z link 2: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue and green) 57
58 8) Microstrip line with voids in GND plane MS SE GND voids (J74-J75) Solution: 4_MicrostipSingle(2) Measured: cmp28_gnd_voids_p1j74_p2j75.s2p Selector/Project/Circuit: MS_SE_GND_Voids_J74_J75 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional 3 discontinuity selectors are added around all voids in the reference plane; See also notes in the solution; 58
59 8) Microstrip line with voids in GND plane: Magnitude of S-parameters Transmission Discrepancies above GHz Not clear what causes substantial differences above GHz; Reflection Measured: lines with stars Model: lines with circles 59
60 8) Microstrip line with voids in GND plane : Magnitude of transmission parameter Not clear what causes substantial differences above 20 GHz; Measured: lines with stars Model: lines with circles 60
61 8) Microstrip line with voids in GND plane : Magnitude of reflection parameter Not clear what causes substantial differences above GHz; Measured: lines with stars Model: lines with circles 61
62 8) Microstrip line with voids in GND plane: Transmission phase and group delay Group Delay Measured: lines with stars Model: lines with circles Phase Delay 62
63 8) Microstrip line with voids in GND plane: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue and green) 63
64 9) Microstrip with gradual coplanar section MS SE Gradual Coplanar (J69-J70) Solution: 4_MicrostipSingle(2) Measured: cmp28_graduate_coplanar_p1j70_p2j69.s2 p Selector/Project/Circuit: MS_SE_GraduateCoplanar_J70_J69 Board Analyzer: Trace width is adjusted outside of coplanar section; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional discontinuity selector is added for part of the gradual coplanar section; See also notes in the solution; 64
65 9) Microstrip with gradual coplanar section: Magnitude of S-parameters Transmission Reflection Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 65
66 9) Microstrip with gradual coplanar section: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 66
67 9) Microstrip with gradual coplanar section: TDR with 20 ps Gaussian step Measured (red and orange) Trace width is not adjusted in the coplanar section; Model (blue and green) 67
68 10) Microstrip line with inductive via MS SE with inductive via (J15-J16) Solution: 4_MicrostipSingle(2) Measured: cmp28_via_inductive_p1j15_p2j16.s2p Selector/Project/Circuit: MS_SE_Via_Inductive_J15_J16 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to reuse PCB/MS_ConnectorAndLaunch model; Additional discontinuity selector is added for via; See also notes in the solution; 68
69 10) Microstrip line with inductive via: Magnitude of S-parameters Reflection Transmission Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 69
70 10) Microstrip line with inductive via: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 70
71 10) Microstrip line with inductive via: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue) 71
72 11) Microstrip line with capacitive via MS SE with capacitive via (J19-J20) Solution: 4_MicrostipSingle(2) Measured: cmp28_via_capacitive_p1j19_p2j20.s2p Selector/Project/Circuit: MS_SE_Via_Capacitive_J19_J20 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional discontinuity selector is added for via; See also notes in the solution; 72
73 11) Microstrip line with capacitive via: Magnitude of S-parameters Reflection Transmission Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 73
74 11) Microstrip line with capacitive via: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 74
75 11) Microstrip line with capacitive via: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue) 75
76 12) Microstrip line with two capacitive via MS SE with 2 capacitive via (J65-J66) Solution: 4_MicrostipSingle(2) Measured: cmp28_via_pathology_p1j65_p2j66.s2p Selector/Project/Circuit: MS_SE_Via_Pathology_J65_J66 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional discontinuity selectors are added for via (identical and re-used); See also notes in the solution; 76
77 12) Microstrip line with two capacitive via: Magnitude of S-parameters Transmission Reflection Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 77
78 12) Microstrip line with two capacitive via: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 78
79 12) Microstrip line with two capacitive via: TDR with 20 ps Gaussian step Model (blue) Measured (red and orange) 79
80 12) Microstrip line with two capacitive via: 28 Gbps PRBS, 25 ps rise/fall time Model (green) Measured (blue) Eyes are on top of each other! 80
81 13) 2-inch microstrip differential line MS DF 2-inch segment (J33-J34-J37-J38) Solution: 5_MicrostipDifferential(1) Measured: cmp28_mstrp_diff_2inch_j38j37j34j33.s4p Selector/Project/Circuit: MS_DF_2inch See notes on the decomposition in solution and on the next slide Board Analyzer: Single-ended trace width is adjusted after the extraction; 4 discontinuity selectors for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional 2 discontinuity selectors are added for transitions from singleended to differential (identical and re-used); See also notes in the solution; 81
82 13) 2-inch microstrip differential line: De-compositional analysis Board Analyzer: 4 discontinuity selectors for launches; 2 selectors for transitions; Gradual transition (identical on both ends) Auto-extraction Single-ended segments Differential segment United Connector + Launch model from PCB/MS_ConnectorAndLaunch See also solution notes for MS DF 2-inch segment 82
83 13) 2-inch microstrip differential line: Single-ended transmission and reflection SE Transmission SE Reflection Difference in strip width and separation explains difference in transmission resonance; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 83
84 13) 2-inch microstrip differential line: Single-ended near and far end x-talk SE FEXT SE NEXT Measured: lines with stars Model: lines with circles NEXT- near end cross-talk; FEXT - far end cross-talk; 84
85 13) 2-inch microstrip differential line: SE transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Some discrepancies above 30 GHz Phase Delay 85
86 13) 2-inch microstrip differential line: SE TDR with 20 ps Gaussian step Measured Model Model transitions have lower impedance due to no adjustments in trace width in the tapered polygonal section; 86
87 13) 2-inch microstrip differential line: Differential mode transmission and reflection DM Transmission DM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; DM differential mode 87
88 13) 2-inch microstrip differential line: Common mode transmission and reflection CM Transmission CM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; CM common mode 88
89 13) 2-inch microstrip differential line: Mixed mode transformation Measured: lines with stars Model: lines with circles NEMT Difference below -30 db can be attributed to many things; FEMT NEMT- near end differential to common mode transformation; FEMT - far end differential to common mode transformation; 89
90 13) 2-inch microstrip differential line: DF transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Common Mode Phase Delay Differential Mode 90
91 13) 2-inch microstrip differential line: MM TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 91
92 14) 6-inch microstrip differential line MS DF 6-inch segment (J41-J42-J45-J46) Solution: 5_MicrostipDifferential(1) Measured: cmp28_mstrp_diff_6inch_j46j45j42j41.s4p Selector/Project/Circuit: MS_DF_6inch Board Analyzer: Single-ended trace width is adjusted; 4 discontinuity selectors for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional 2 discontinuity selectors are added for transitions from single-ended to differential (identical and re-used); See also notes in the solution; 92
93 14) 6-inch microstrip differential line: Single-ended transmission and reflection SE Transmission SE Reflection Difference in strip width and separation explains difference in transmission resonance; Variation of trace width and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles 93
94 14) 6-inch microstrip differential line: Single-ended near and far end x-talk SE FEXT Measured: lines with stars Model: lines with circles SE NEXT NEXT- near end cross-talk; FEXT - far end cross-talk; 94
95 14) 6-inch microstrip differential line: SE transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 95
96 14) 6-inch microstrip differential line: SE TDR with 20 ps Gaussian step Measured Model Model transitions have lower impedance due to no adjustments in trace width in the tapered polygonal section; 96
97 14) 6-inch microstrip differential line: Differential mode transmission and reflection DM Transmission DM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; DM differential mode 97
98 14) 6-inch microstrip differential line: Common mode transmission and reflection CM Transmission CM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; CM common mode 98
99 14) 6-inch microstrip differential line: Mixed mode transformation Measured: lines with stars Model: lines with circles NEMT Difference below -30 db can be attributed to many things; FEMT NEMT- near end differential to common mode transformation; FEMT - far end differential to common mode transformation; 99
100 14) 6-inch microstrip differential line: DF transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Common Mode Phase Delay Differential Mode 100
101 14) 6-inch microstrip differential line: MM TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 101
102 14) 6-inch microstrip differential line: 28 Gbps PRBS, 25 ps rise/fall time Model (green) Measured (blue) Eyes are on top of each other! 102
103 15) Microstrip differential line with void MS DF segment with void in GND plane (J55- J56-J59-J60) Solution: 6_MicrostipDifferential(2) Measured: cmp28_mstrp_diff_gnd_cutout_j59j60j55j56. s4p Selector/Project/Circuit: MS_DF_GND_Cutout Board Analyzer: Single-ended trace width is adjusted; 4 discontinuity selectors for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; Additional 2 discontinuity selectors are added for transitions from single-ended to differential (identical and re-used from 2-inch diff line); See also notes in the solution; 103
104 15) Microstrip differential line with void: Single-ended transmission SE Transmission over cutout SE Transmission over solid plane Difference in strip width and separation explains difference in transmission; Measured: lines with stars Model: lines with circles 104
105 15) Microstrip differential line with void: Single-ended reflection SE Reflection over solid plane SE Reflection over cutout Difference in strip width, separation and dielectric properties explains difference in reflection; Measured: lines with stars Model: lines with circles 105
106 15) Microstrip differential line with void: SE TDR with 20 ps Gaussian step Measured: red, orange, light blue and green; Model: blue and green; Model transitions have lower impedance due to no adjustments in trace width in the tapered polygonal section; 106
107 15) Microstrip differential line with void: Differential mode transmission and reflection DM Transmission Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; DM Reflection Measured: lines with stars Model: lines with circles DM differential mode 107
108 15) Microstrip differential line with void: Common mode transmission and reflection CM Transmission Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; CM Reflection Measured: lines with stars Model: lines with circles CM common mode 108
109 15) Microstrip differential line with void: Mixed mode transformation NEMT Difference below -30 db can be attributed to many things; FEMT Measured: lines with stars Model: lines with circles NEMT- near end differential to common mode transformation; FEMT - far end differential to common mode transformation; 109
110 15) Microstrip differential line with void: DF transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Group delay is too noisy to make conclusions Phase Delay Common Mode Differential Mode 110
111 15) Microstrip differential line with void: MM TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 111
112 15) Microstrip differential line with void: 28 Gbps PRBS, 25 ps rise/fall time Model (green) Measured (blue) Eyes are on top of each other! 112
113 16) Microstrip differential line with vias MS DF segment with void in GND plane (J55- J56-J59-J60) Solution: 6_MicrostipDifferential(2) Measured: cmp28_mstrp_diff_vias_j49j50j51j52.s4p Selector/Project/Circuit: MS_DF_Vias Board Analyzer: Single-ended trace width is adjusted; 4 discontinuity selectors for the launches are set to reuse PCB/MS_ConnectorAndLaunch model; 2 discontinuity selectors are added for transitions from single-ended to differential (identical and re-used from 2-inch diff line); Additional selector created for vias (shown on the right) See also notes in the solution; 113
114 16) Microstrip differential line with vias: Differential mode transmission and reflection DM Transmission DM Reflection Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; Measured: lines with stars Model: lines with circles DM differential mode 114
115 16) Microstrip differential line with vias: Common mode transmission and reflection CM Transmission Measured: lines with stars Model: lines with circles Loss of common mode localization above GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; CM Reflection CM common mode 115
116 16) Microstrip differential line with vias: Mixed mode transformation NEMT Difference below -30 db can be attributed to many things; FEMT Measured: lines with stars Model: lines with circles NEMT- near end differential to common mode transformation; FEMT - far end differential to common mode transformation; 116
117 16) Microstrip differential line with vias: DF transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Differential mode is OK; Discrepancies in common above 20 GHz; Phase Delay Common Mode Differential Mode 117
118 16) Microstrip differential line with vias: Differential TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 118
119 17) X-talk in differential microstrip J53 MS DF segment with cross-talk (J53-J54-J57-J58-J61-J64- J57 J71-J72) J54 Solution: 7_MicrostipDifferentialXTalk(3) J61 Measured: Through Long: mp28_mstrp_diff_xtalk_j57j64j53j72.s4p J71 J64 J58 Through Short: cmp28_mstrp_diff_xtalk_j71j72j61j64.s4p J72 NEXT Left: cmp28_mstrp_diff_xtalk_j57j71j53j61.s4p NEXT Right: cmp28_mstrp_diff_xtalk_j72j58j64j54.s4p FEXT Left-Right: cmp28_mstrp_diff_xtalk_j57j72j53j64.s4p FEXT Right-Left: cmp28_mstrp_diff_xtalk_j71j58j61j54.s4p Selector/Project/Circuit: MS_DF_XTalk Board Analyzer: Single-ended trace width is adjusted; 8 discontinuity selectors for the launches are set to re-use PCB/MS_ConnectorAndLaunch model; 2 discontinuity selectors are added for transitions from single-ended to differential (identical and re-used); 2 discontinuity selectors are added for transitions to differential coupled section (identical and re-used); PORT NUMERATION CORRESPONDENSE (DS for pins are created in this order): Pins J53 and J57 - Port 1 and 2 (differential port 1, common port 5); Pins J61 and J71 - Port 3 and 4 (differential port 2, common port 6); Pins J54 and J58 - Port 5 and 6 (differential port 3, common port 7); Pins J64 and J72 - Port 7 and 8 (differential port 4, common port 8); See also notes in the solution; 119
120 17) X-talk in differential microstrip: Long section transmission and reflection DM Transmission DM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; DM differential mode 120
121 17) X-talk in differential microstrip: Long section TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 121
122 17) X-talk in differential microstrip: Short section transmission and reflection DM Transmission DM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variation of trace width, separation and dielectric properties explains differences in reflection losses; DM differential mode 122
123 17) X-talk in differential microstrip: Short section TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 123
124 17) X-talk in differential microstrip: Near end mixed-mode X-talk Measured: lines with stars Model: lines with circles 124
125 17) X-talk in differential microstrip: Mixed-mode NEXT TDR with 20 ps Gaussian step Near end Common to Common mode x-talk Larger common mode NEXT; Measured: A lines Model: B lines 125
126 17) X-talk in differential microstrip: Far end mixed-mode X-talk Measured: lines with stars Model: lines with circles 126
127 17) X-talk in differential microstrip: Mixed-mode NEXT TDR with 20 ps Gaussian step Measured: A lines Model: B lines 127
128 18) 2-inch strip line segment SL SE 2-inch segment (J5-J6) Solution: 8_StipSingle(1) Measured: cmp28_strpl_2in_50ohm_p1j6_p2j5.s2p Selector/Project/Circuit: SL_SE_2inch_J6J5 Board Analyzer: Trace width is adjusted (11 to 10.5 mil); 2 discontinuity selector for the launches (identical); See also notes on next slide and in the solution; 128
129 18) 2-inch strip line segment: De-compositional analysis Board Analyzer: 2 discontinuity selectors with coaxial ports Trace width is adjusted in BA Simbeor SFS Auto-extraction Connector + adapter model (added) Connector + Launch are also simulated separately in PCB/SL_ConnectorAndLaunch for further reuse Launch model (back-drilled) Simbeor 3DML Connector + adapter model (added) See also solution notes for SL SE 2-inch segment 129
130 18) 2-inch strip line segment: Magnitude of S-parameters Reflection Transmission MS Launch looses the localization at about 30 GHz: Distance from signal via to stitching vias is about quarter of wavelength at 30 GHz we cannot expect correlation above that frequency! Though, the impedance of the return path remains low due to plenty of stitching vias. Measured: lines with stars Model: lines with circles 130
131 18) 2-inch strip line segment: Transmission phase and group delay Group Delay Measured: lines with stars Model: lines with circles Phase Delay 131
132 18) 2-inch strip line segment: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue) Variations of impedance along the traces visible here indicates that either trace width is varying or dielectric is inhomogeneous (or both); This is not accounted for in the model and explains differences in the reflection. 132
133 18) 2-inch strip line segment: 28 Gbps PRBS, 25 ps rise/fall time Measured (blue) Eyes are on top of each other! Model (green) 133
134 19) 8-inch strip line segment SL SE 8-inch segment (J7-J8) Solution: 8_StipSingle(1) Measured: cmp28_strpl_8inch_p1j7_p2j8.s2p Selector/Project/Circuit: SL_SE_8inch_J7J8 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches (identical and set to re-use PCB\SL_ConnectorAndLaunch constructed with launch model from 2- inch segment analysis); See also notes in the solution; 134
135 19) 8-inch strip line segment: Magnitude of S-parameters Transmission Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Differences in back-drilling, variation of trace width and dielectric properties explains differences in reflection losses; 135
136 19) 8-inch strip line segment: Transmission phase and group delay Group Delay Measured: lines with stars Model: lines with circles Phase Delay 136
137 19) 8-inch strip line segment: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue) Variations of impedance along the traces visible here indicates that either trace width is varying or dielectric is inhomogeneous (or both); This is not accounted for in the model and explains differences in the reflection. 137
138 19) 8-inch strip line segment: 28 Gbps PRBS, 25 ps rise/fall time Measured (blue) Model (green) Eyes are on top of each other! 138
139 20) Strip 25-Ohm Beatty standard SL SE Beatty standard (J27-J28) Solution: 8_StipSingle(1) Measured: cmp28_strpl_beatty_25ohm_p1j28_p2j27.s2p Selector/Project/Circuit: SL_SE_Beatty_25Ohm_J28J27 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches (identical and set to re-use PCB\SL_ConnectorAndLaunch constructed with launch model from 2-inch segment analysis); Additional 2 discontinuity selectors created for steps (identical and re-used); See also notes in the solution; 139
140 20) Strip 25-Ohm Beatty standard: Magnitude of S-parameters Transmission Loss of launch localization above 30 GHz explains additional insertion losses; Differences in back-drilling, variation of trace width and dielectric properties explains differences in reflection losses; Reflection Measured: lines with stars Model: lines with circles 140
141 20) Strip 25-Ohm Beatty standard: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 141
142 20) Strip 25-Ohm Beatty standard: TDR with 20 ps Gaussian step Model (blue) Measured (red and orange) 142
143 21) Strip stub resonator SL SE strip stub resonator (J23-J24) Solution: 8_StipSingle(1) Measured: cmp28_strpl_resonator_p1j23_p2j24.s2p Selector/Project/Circuit: SL_SE_Resonator_J23J24 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches (identical and set to re-use PCB\SL_ConnectorAndLaunch constructed with launch model from 2-inch segment analysis); Additional discontinuity selector is created for X-junction and 2 discontinuity selectors are created for open-ends (identical and re-used); See also notes in the solution; 143
144 21) Strip stub resonator: Magnitude of S-parameters Transmission Loss of launch localization above 30 GHz explains additional insertion losses; Differences in back-drilling, variation of trace width and dielectric properties explains differences in reflection losses; Reflection Measured: lines with stars Model: lines with circles 144
145 21) Strip stub resonator: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 145
146 21) Strip stub resonator: TDR with 20 ps Gaussian step Measured (red and orange) Model (blue) 146
147 22) Strip line with capacitive via SL SE strip with capacitive via (J17-J18) Solution: 9_StipSingle(2) Measured: cmp28_strpl_via_capacitive_p1j18_p2j17.s2p Selector/Project/Circuit: SL_SE_Via_Capacitive_J18J17 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches (identical and set to re-use PCB\SL_ConnectorAndLaunch constructed with launch model from 2-inch segment analysis); Additional discontinuity selector is created for via (shown on the right); See also notes in the solution; Via has stubs and small anti-pads in PLANE_2 and Plane_7 147
148 22) Strip line with capacitive via: Magnitude of S-parameters Transmission Reflection Loss of launch localization above 30 GHz explains additional insertion losses; Variation of via geometry explains differences in reflection losses; Measured: lines with stars Model: lines with circles 148
149 22) Strip line with capacitive via: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Discrepancies above 30 GHz Phase Delay 149
150 22) Strip line with capacitive via: TDR with 20 ps Gaussian step Model (blue) Measured (red and orange) Variations of via geometry may explain additional capacitance (off-center drilling for instance); 150
151 23) Strip line with back-drilled via SL SE strip with back-drilled via (J13-J14) Solution: 9_StipSingle(2) Measured: cmp28_strpl_via_backdrilled_p1j14_p2j13.s2p Selector/Project/Circuit: SL_SE_Via_Backdrilled_J14J13 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches (identical and set to re-use PCB\SL_ConnectorAndLaunch constructed with launch model from 2-inch segment analysis); Additional discontinuity selector is created for via and edited after extraction (shown on the right); See also notes in the solution; Via barrel span is from PLANE_2 to Plane_7 (worst case back-drill) 151
152 23) Strip line with back-drilled via: Magnitude of S-parameters Reflection Transmission Discrepancies above 30 GHz Variation of via geometry (back-drilling) explains differences both in insertion and reflection losses; Measured: lines with stars Model: lines with circles 152
153 23) Strip line with back-drilled via: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Discrepancies above 30 GHz Phase Delay 153
154 23) Strip line with back-drilled via: TDR with 20 ps Gaussian step Variations of via back-drilling and trace geometry explains differences; Model (blue) Measured (red and orange) 154
155 24) 2-inch strip line with capacitive launch SL SE 2 in strip with capacitive launch (J9- J10) Solution: 9_StipSingle(2) Measured: cmp28_strpl_2in_capacitive_p1j10_p2j09.s2p Selector/Project/Circuit: SL_SE_2inch_Capacitive_J9J10 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are created and edited after extraction to account for the back-drilling (identical and set to reused); Connector models are added to linear network after the extraction; See also notes in the solution; Via barrel is reduced to PLANE_5; Small anti-pads in PLANE_5 and PLANE_7 (capacitive); 155
156 24) 2-inch strip line with capacitive launch: Magnitude of S-parameters Transmission Reflection Variation of via geometry (back-drilling) explains differences both in insertion and reflection losses; Measured: lines with stars Model: lines with circles 156
157 24) 2-inch strip line with capacitive launch: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 157
158 24) 2-inch strip line with capacitive launch: TDR with 20 ps Gaussian step Model (blue) Measured (red and orange) Variations of via back-drilling and trace geometry explains differences; 158
159 25) 2-inch strip line with inductive launch SL SE 2 in strip with inductive launch (J11- J12) Solution: 9_StipSingle(2) Measured: cmp28_strpl_2in_inductive_p1j12_p2j11.s2p Selector/Project/Circuit: SL_SE_2inch_Inductive_J11J12 Board Analyzer: Trace width is adjusted; 2 discontinuity selector for the launches are created and edited after extraction to account for the back-drilling (identical and set to reused); Connector models are added to linear network after the extraction; See also notes in the solution; Via barrel is reduced to PLANE_5; Large anti-pads in PLANE_5 and PLANE_7 (inductive); 159
160 25) 2-inch strip line with inductive launch: Magnitude of S-parameters Transmission Reflection Variation of via geometry (back-drilling) explains differences both in insertion and reflection losses; Measured: lines with stars Model: lines with circles 160
161 25) 2-inch strip line with inductive launch: Transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay 161
162 25) 2-inch strip line with inductive launch: TDR with 20 ps Gaussian step Measured (red and orange) Variations of via back-drilling and trace geometry explains differences; Model (blue) 162
163 26) 2-inch strip differential line SL DF 2-inch segment (J35-J36-J39-J40) Solution: 10_StipDifferential(1) Measured: cmp28_strpl_diff_2inch_j39j40j35j36.s4p Selector/Project/Circuit: SL_DF_2inch See notes on the decomposition in solution and on the next slide Board Analyzer: Single-ended trace width is adjusted after the extraction; 4 discontinuity selectors for the launches are set to re-use PCB/SL_ConnectorAndLaunch model; Additional 2 discontinuity selectors are added for transitions from singleended to differential (identical and re-used); See also notes in the solution; 163
164 26) 2-inch strip differential line: De-compositional analysis Board Analyzer: 4 discontinuity selectors for launches; 2 selectors for transitions; Gradual transition (identical on both ends) Auto-extraction Single-ended segments Differential segment United Connector + Launch model from PCB/SL_ConnectorAndLaunch See also solution notes for MS DF 2-inch segment 164
165 26) 2-inch strip differential line: Single-ended transmission and reflection SE Reflection SE Transmission Discrepancies above 30 GHz Loss of localization and difference in launch geometry (back-drilling) explain difference in transmission and reflection; Measured: lines with stars Model: lines with circles 165
166 26) 2-inch strip differential line: Single-ended near and far end x-talk SE NEXT Measured: lines with stars Model: lines with circles SE FEXT NEXT- near end cross-talk; FEXT - far end cross-talk; 166
167 26) 2-inch strip differential line: SE transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Discrepancies above 40 GHz Phase Delay 167
168 26) 2-inch strip differential line: SE TDR with 20 ps Gaussian step Measured Model Model transitions have lower impedance due to no adjustments in trace width in the tapered polygonal section; 168
169 26) 2-inch strip differential line: Differential mode transmission and reflection DM Transmission DM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variations in back-drilling, trace width, separation and dielectric properties explains differences in reflection losses; DM differential mode 169
170 26) 2-inch strip differential line: Common mode transmission and reflection CM Transmission CM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variations in back-drilling, trace width, separation and dielectric properties explains differences in reflection losses; CM common mode 170
171 26) 2-inch strip differential line: Mixed mode transformation Measured: lines with stars Model: lines with circles NEMT Difference below -30 db can be attributed to many things; FEMT NEMT- near end differential to common mode transformation; FEMT - far end differential to common mode transformation; 171
172 26) 2-inch strip differential line: DF transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay Phase Delay Discrepancies above 40 GHz; About 5 ps difference due to resin between strips? 172
173 26) 2-inch strip differential line: MM TDR with 20 ps Gaussian step Measured (differential mode) Model (differential mode) Common mode modeled and measured Model transitions have lower impedance due to no adjustments in trace width in polygonal section; 173
174 27) 6-inch strip differential line SL DF 6-inch segment (J43-J44-J47-J48) Solution: 10_StipDifferential(1) Measured: cmp28_strpl_diff_6inch_j47j48j43j44.s4p Selector/Project/Circuit: SL_DF_6inch Board Analyzer: Single-ended trace width is adjusted after the extraction; 4 discontinuity selectors for the launches are set to re-use PCB/SL_ConnectorAndLaunch model; Additional 2 discontinuity selectors are added for transitions from singleended to differential (identical and re-used from analysis of 2-inch segment); See also notes in the solution; 174
175 27) 6-inch strip differential line: Single-ended transmission and reflection SE Reflection SE Transmission Discrepancies above 35 GHz Loss of localization and difference in launch geometry (back-drilling) explain difference in transmission and reflection; Measured: lines with stars Model: lines with circles 175
176 27) 6-inch strip differential line: Single-ended near and far end x-talk SE NEXT Measured: lines with stars Model: lines with circles Difference in FEXT indicates inhomogeneity of dielectric (resin between strips); SE FEXT NEXT- near end cross-talk; FEXT - far end cross-talk; 176
177 27) 6-inch strip differential line: SE transmission phase and group delay Measured: lines with stars Model: lines with circles Group Delay About 7 ps difference in phase delay due to resin between strips? Phase Delay 177
178 27) 6-inch strip differential line: SE TDR with 20 ps Gaussian step Measured Model impedance is lower by about 1 Ohm; Model 178
179 27) 6-inch strip differential line: Differential mode transmission and reflection DM Reflection DM Transmission Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variations in back-drilling, trace width, separation and dielectric properties explains differences in reflection losses; DM differential mode 179
180 27) 6-inch strip differential line: Common mode transmission and reflection CM Transmission CM Reflection Measured: lines with stars Model: lines with circles Loss of launch localization above 30 GHz explains additional insertion losses; Variations in back-drilling, trace width, separation and dielectric properties explains differences in reflection losses; CM common mode 180
181 27) 6-inch strip differential line: Mixed mode transformation Measured: lines with stars Model: lines with circles NEMT Difference below -30 db can be attributed to many things; FEMT NEMT- near end differential to common mode transformation; FEMT - far end differential to common mode transformation; 181
Design Insights from Electromagnetic Analysis of Interconnects
Design Insights from Electromagnetic Analysis of Interconnects Yuriy Shlepnev, Simberian Inc. shlepnev@simberian.com Front Range Signal Integrity Seminar, Longmont, CO October 3, 2013 10/8/2013 2013 Simberian
More informationDesign and Optimization of a Novel 2.4 mm Coaxial Field Replaceable Connector Suitable for 25 Gbps System and Material Characterization up to 50 GHz
Design and Optimization of a Novel 2.4 mm Coaxial Field Replaceable Connector Suitable for 25 Gbps System and Material Characterization up to 50 GHz Course Number: 13-WA4 David Dunham, Molex Inc. David.Dunham@molex.com
More informationElectromagnetic Analysis of AC Coupling Capacitor Mounting Structures
Simbeor Application Note #2008_02, April 2008 2008 Simberian Inc. Electromagnetic Analysis of AC Coupling Capacitor Mounting Structures Simberian, Inc. www.simberian.com Simbeor : Easy-to-Use, Efficient
More informationEffect of slots in reference planes on signal propagation in single and differential t-lines
Simbeor Application Note #2007_09, November 2007 2007 Simberian Inc. Effect of slots in reference planes on signal propagation in single and differential t-lines Simberian, Inc. www.simberian.com Simbeor:
More informationMinimization of Reflection from AC Coupling Capacitors
Simbeor Application Note #2008_04, September 2008 2008 Simberian Inc. Minimization of Reflection from AC Coupling Capacitors Simberian, Inc. www.simberian.com Simbeor : Easy-to-Use, Efficient and Cost-Effective
More informationLessons learned: How to Make Predictable PCB Interconnects for Data Rates of 50 Gbps and Beyond
DesignCon 2014 Lessons learned: How to Make Predictable PCB Interconnects for Data Rates of 50 Gbps and Beyond Wendem Beyene, Rambus Inc. wbeyene@rambus.com Yeon-Chang Hahm, Rambus Inc. Jihong Ren, Rambus
More informationCalibration and De-Embedding Techniques in the Frequency Domain
Calibration and De-Embedding Techniques in the Frequency Domain Tom Dagostino tom@teraspeed.com Alfred P. Neves al@teraspeed.com Page 1 Teraspeed Labs Teraspeed Consulting Group LLC 2008 Teraspeed Consulting
More informationDemystifying Vias in High-Speed PCB Design
Demystifying Vias in High-Speed PCB Design Keysight HSD Seminar Mastering SI & PI Design db(s21) E H What is Via? Vertical Interconnect Access (VIA) An electrical connection between layers to pass a signal
More informationDesign of optimal differential viaholes for 6-plane board
Simbeor Application Note #2007_08, October 2007 2007 Simberian Inc. Design of optimal differential viaholes for 6-plane board Simberian, Inc. www.simberian.com Simbeor: Easy-to-Use, Efficient and Cost-Effective
More informationPCB Routing Guidelines for Signal Integrity and Power Integrity
PCB Routing Guidelines for Signal Integrity and Power Integrity Presentation by Chris Heard Orange County chapter meeting November 18, 2015 1 Agenda Insertion Loss 101 PCB Design Guidelines For SI Simulation
More informationYuriy Shlepnev, Simberian Inc Alfred Neves, Teraspeed Consulting Group
DesignCon 2010 Practical identification of dispersive dielectric models with generalized modal S-parameters for analysis of interconnects in 6-100 Gb/s applications Yuriy Shlepnev, Simberian Inc. shlepnev@simberian.com,
More informationPI3HDMIxxx 4-Layer PCB Layout Guideline for HDMI Products
PI3HDMIxxx 4-Layer PCB Layout Guideline for HDMI Products Introduction The differential trace impedance of HDMI is specified at 100Ω±15% in Test ID 8-8 in HDMI Compliance Test Specification Rev.1.2a and
More informationCROSSTALK DUE TO PERIODIC PLANE CUTOUTS. Jason R. Miller, Gustavo Blando, Istvan Novak Sun Microsystems
CROSSTALK DUE TO PERIODIC PLANE CUTOUTS Jason R. Miller, Gustavo Blando, Istvan Novak Sun Microsystems 1 Outline 1 Introduction 2 Crosstalk Theory 3 Measurement 4 Simulation correlation 5 Parameterized
More informationThe Design & Test of Broadband Launches up to 50 GHz on Thin & Thick Substrates
The Performance Leader in Microwave Connectors The Design & Test of Broadband Launches up to 50 GHz on Thin & Thick Substrates Thin Substrate: 8 mil Rogers R04003 Substrate Thick Substrate: 30 mil Rogers
More informationDL-150 The Ten Habits of Highly Successful Designers. or Design for Speed: A Designer s Survival Guide to Signal Integrity
Slide -1 Ten Habits of Highly Successful Board Designers or Design for Speed: A Designer s Survival Guide to Signal Integrity with Dr. Eric Bogatin, Signal Integrity Evangelist, Bogatin Enterprises, www.bethesignal.com
More informationCHAPTER 5 PRINTED FLARED DIPOLE ANTENNA
CHAPTER 5 PRINTED FLARED DIPOLE ANTENNA 5.1 INTRODUCTION This chapter deals with the design of L-band printed dipole antenna (operating frequency of 1060 MHz). A study is carried out to obtain 40 % impedance
More informationHigh Speed Characterization Report
ESCA-XX-XX-XX.XX-1-3 Mated with: SEAF8-XX-05.0-X-XX-2-K SEAM8-XX-S02.0-X-XX-2-K Description: 0.80 mm SEARAY High-Speed/High-Density Array Cable Assembly, 34 AWG Samtec, Inc. 2005 All Rights Reserved Table
More informationA MATERIAL WORLD Modeling dielectrics and conductors for interconnects operating at Gbps
TITLE A MATERIAL WORLD Modeling dielectrics and conductors for interconnects operating at 10-50 Gbps C. Nwachukwu, (Isola) Y. Shlepnev, (Simberian) S. McMorrow, (Teraspeed-Samtec) Image Practical PCB Material
More informationHigh Speed Characterization Report
SSW-1XX-22-X-D-VS Mates with TSM-1XX-1-X-DV-X Description: Surface Mount Terminal Strip,.1 [2.54mm] Pitch, 13.59mm (.535 ) Stack Height Samtec, Inc. 25 All Rights Reserved Table of Contents Connector Overview...
More informationHigh Speed Characterization Report
ERCD_020_XX_TTR_TED_1_D Mated with: ERF8-020-05.0-S-DV-L Description: 0.8mm Edge Rate High Speed Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly Overview... 1
More informationChallenges and Solutions for Removing Fixture Effects in Multi-port Measurements
DesignCon 2008 Challenges and Solutions for Removing Fixture Effects in Multi-port Measurements Robert Schaefer, Agilent Technologies schaefer-public@agilent.com Abstract As data rates continue to rise
More informationHigh Speed Characterization Report
HLCD-20-XX-TD-BD-2 Mated with: LSHM-120-XX.X-X-DV-A Description: 0.50 mm Razor Beam High Speed Hermaphroditic Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly
More informationControlled Impedance Line Designer
Heidi Barnes WW HSD Application Engineer Controlled Impedance Line Designer Stephen Slater HSD Product Manager EDA Simulation Tools for Power Integrity Agenda 1. Designing a channel for a desired impedance
More informationSignal Integrity Tips and Techniques Using TDR, VNA and Modeling. Russ Kramer O.J. Danzy
Signal Integrity Tips and Techniques Using TDR, VNA and Modeling Russ Kramer O.J. Danzy Simulation What is the Signal Integrity Challenge? Tx Rx Channel Asfiakhan Dreamstime.com - 3d People Communication
More informationHigh Speed Characterization Report
QTH-030-01-L-D-A Mates with QSH-030-01-L-D-A Description: High Speed Ground Plane Header Board-to-Board, 0.5mm (.0197 ) Pitch, 5mm (.1969 ) Stack Height Samtec, Inc. 2005 All Rights Reserved Table of Contents
More informationThe Effect of Radiation Losses on High Frequency PCB Performance. John Coonrod Rogers Corporation Advanced Circuit Materials Division
he Effect of adiation osses on High Frequency PCB Performance John Coonrod ogers Corporation Advanced Circuit Materials Division he Effect of adiation osses on High Frequency PCB Performance Basic concepts
More informationA Signal Integrity Measuring Methodology in the Extraction of Wide Bandwidth Environmental Coefficients
As originally published in the IPC APEX EXPO Conference Proceedings. A Signal Integrity Measuring Methodology in the Extraction of Wide Bandwidth Environmental Coefficients Eric Liao, Kuen-Fwu Fuh, Annie
More informationA Simplified QFN Package Characterization Technique
Slide -1 A Simplified QFN Package Characterization Technique Dr. Eric Bogatin and Trevor Mitchell Bogatin Enterprises Dick Otte, President, Promex 8/1/10 Slide -2 Goal of this Project Develop a simple
More informationDesign and Matching of a 60-GHz Printed Antenna
Application Example Design and Matching of a 60-GHz Printed Antenna Using NI AWR Software and AWR Connected for Optenni Figure 1: Patch antenna performance. Impedance matching of high-frequency components
More informationResearch Article Compact and Wideband Parallel-Strip 180 Hybrid Coupler with Arbitrary Power Division Ratios
Microwave Science and Technology Volume 13, Article ID 56734, 1 pages http://dx.doi.org/1.1155/13/56734 Research Article Compact and Wideband Parallel-Strip 18 Hybrid Coupler with Arbitrary Power Division
More informationHow to Read S-Parameters Like a Book or Tapping Into Some Of The Information Buried Inside S- Parameter Black Box Models
Slide -1 Bogatin Enterprises and LeCroy Corp No Myths Allowed Webinar Time before start: How to Read S-Parameters Like a Book or Tapping Into Some Of The Information Buried Inside S- Parameter Black Box
More informationDesign, Optimization, Fabrication, and Measurement of an Edge Coupled Filter
SYRACUSE UNIVERSITY Design, Optimization, Fabrication, and Measurement of an Edge Coupled Filter Project 2 Colin Robinson Thomas Piwtorak Bashir Souid 12/08/2011 Abstract The design, optimization, fabrication,
More informationBill Ham Martin Ogbuokiri. This clause specifies the electrical performance requirements for shielded and unshielded cables.
098-219r2 Prepared by: Ed Armstrong Zane Daggett Bill Ham Martin Ogbuokiri Date: 07-24-98 Revised: 09-29-98 Revised again: 10-14-98 Revised again: 12-2-98 Revised again: 01-18-99 1. REQUIREMENTS FOR SPI-3
More informationHow to anticipate Signal Integrity Issues: Improve my Channel Simulation by using Electromagnetic based model
How to anticipate Signal Integrity Issues: Improve my Channel Simulation by using Electromagnetic based model HSD Strategic Intent Provide the industry s premier HSD EDA software. Integration of premier
More informationHigh Speed Characterization Report
PCRF-064-XXXX-EC-SMA-P-1 Mated with: PCIE-XXX-02-X-D-TH Description: PCI Express Cable Assembly, Low Loss Microwave Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly Overview...
More informationResearch Article A Parallel-Strip Balun for Wideband Frequency Doubler
Microwave Science and Technology Volume 213, Article ID 8929, 4 pages http://dx.doi.org/1.11/213/8929 Research Article A Parallel-Strip Balun for Wideband Frequency Doubler Leung Chiu and Quan Xue Department
More informationAN 766: Intel Stratix 10 Devices, High Speed Signal Interface Layout Design Guideline
AN 766: Intel Stratix 10 Devices, High Speed Signal Interface Layout Subscribe Latest document on the web: PDF HTML Contents Contents Intel Stratix 10 Devices, High Speed Signal Interface Layout... 3 Intel
More informationApplication Note 5525
Using the Wafer Scale Packaged Detector in 2 to 6 GHz Applications Application Note 5525 Introduction The is a broadband directional coupler with integrated temperature compensated detector designed for
More informationDL-150 The Ten Habits of Highly Successful Designers. or Design for Speed: A Designer s Survival Guide to Signal Integrity
Slide -1 Ten Habits of Highly Successful Board Designers or Design for Speed: A Designer s Survival Guide to Signal Integrity with Dr. Eric Bogatin, Signal Integrity Evangelist, Bogatin Enterprises, www.bethesignal.com
More informationNew Microstrip-to-CPS Transition for Millimeter-wave Application
New Microstrip-to-CPS Transition for Millimeter-wave Application Kyu Hwan Han 1,, Benjamin Lacroix, John Papapolymerou and Madhavan Swaminathan 1, 1 Interconnect and Packaging Center (IPC), SRC Center
More informationPractical Measurements of Dielectric Constant and Loss for PCB Materials at High Frequency
8 th Annual Symposium on Signal Integrity PENN STATE, Harrisburg Center for Signal Integrity Practical Measurements of Dielectric Constant and Loss for PCB Materials at High Frequency Practical Measurements
More informationHigh Speed Characterization Report
ECDP-16-XX-L1-L2-2-2 Mated with: HSEC8-125-XX-XX-DV-X-XX Description: High-Speed 85Ω Differential Edge Card Cable Assembly, 30 AWG ACCELERATE TM Twinax Cable Samtec, Inc. 2005 All Rights Reserved Table
More informationResearch Article Wideband Microstrip 90 Hybrid Coupler Using High Pass Network
Microwave Science and Technology, Article ID 854346, 6 pages http://dx.doi.org/1.1155/214/854346 Research Article Wideband Microstrip 9 Hybrid Coupler Using High Pass Network Leung Chiu Department of Electronic
More informationOptimization of Wafer Level Test Hardware using Signal Integrity Simulation
June 7-10, 2009 San Diego, CA Optimization of Wafer Level Test Hardware using Signal Integrity Simulation Jason Mroczkowski Ryan Satrom Agenda Industry Drivers Wafer Scale Test Interface Simulation Simulation
More informationDesign of Microstrip Coupled Line Bandpass Filter Using Synthesis Technique
Design of Microstrip Coupled Line Bandpass Filter Using Synthesis Technique 1 P.Priyanka, 2 Dr.S.Maheswari, 1 PG Student, 2 Professor, Department of Electronics and Communication Engineering Panimalar
More informationHigh Speed Characterization Report
PCIEC-XXX-XXXX-EC-EM-P Mated with: PCIE-XXX-02-X-D-TH Description: 1.00 mm PCI Express Internal Cable Assembly, 30 AWG Twinax Ribbon Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable
More informationDDR4 memory interface: Solving PCB design challenges
DDR4 memory interface: Solving PCB design challenges Chang Fei Yee - July 23, 2014 Introduction DDR SDRAM technology has reached its 4th generation. The DDR4 SDRAM interface achieves a maximum data rate
More information/14/$ IEEE 939
Electro-Mechanical Structures for Channel Emulation Satyajeet Shinde #1, Sen Yang #2, Nicholas Erickson #3, David Pommerenke #4, Chong Ding *1, Douglas White *1, Stephen Scearce *1, Yaochao Yang *2 # Missouri
More informationPractical Limitations of State of the Art Passive Printed Circuit Board Power Delivery Networks for High Performance Compute Systems
Practical Limitations of State of the Art Passive Printed Circuit Board Power Delivery Networks for High Performance Compute Systems Presented by Chad Smutzer Mayo Clinic Special Purpose Processor Development
More informationLecture 4. Maximum Transfer of Power. The Purpose of Matching. Lecture 4 RF Amplifier Design. Johan Wernehag Electrical and Information Technology
Johan Wernehag, EIT Lecture 4 RF Amplifier Design Johan Wernehag Electrical and Information Technology Design of Matching Networks Various Purposes of Matching Voltage-, Current- and Power Matching Design
More informationConsiderations in High-Speed High Performance Die-Package-Board Co-Design. Jenny Jiang Altera Packaging Department October 2014
Considerations in High-Speed High Performance Die-Package-Board Co-Design Jenny Jiang Altera Packaging Department October 2014 Why Co-Design? Complex Multi-Layer BGA Package Horizontal and vertical design
More informationA Technical Discussion of TDR Techniques, S-parameters, RF Sockets, and Probing Techniques for High Speed Serial Data Designs
A Technical Discussion of TDR Techniques, S-parameters, RF Sockets, and Probing Techniques for High Speed Serial Data Designs Presenter: Brian Shumaker DVT Solutions, LLC, 650-793-7083 b.shumaker@comcast.net
More informationValidation Report Comparison of Eye Patterns Generated By Synopsys HSPICE and the Agilent PLTS
Comparison of Eye Patterns Generated By Synopsys HSPICE and the Agilent PLTS Using: Final Inch Test/Eval Kit, Differential Pair - No Grounds Configuration, QTE-DP/QSE-DP, 5mm Stack Height (P/N FIK-QxE-04-01)
More informationPART MAX2605EUT-T MAX2606EUT-T MAX2607EUT-T MAX2608EUT-T MAX2609EUT-T TOP VIEW IND GND. Maxim Integrated Products 1
19-1673; Rev 0a; 4/02 EVALUATION KIT MANUAL AVAILABLE 45MHz to 650MHz, Integrated IF General Description The are compact, high-performance intermediate-frequency (IF) voltage-controlled oscillators (VCOs)
More informationExperimental Analysis of Via-hole-ground Effects in Microwave Integrated Circuits at X-band
h y POSTER 215, PRAGUE MAY 14 1 Experimental Analysis of Via-hole-ground Effects in Microwave Integrated Circuits at X-band Ghulam Mustafa Khan Junejo Microwave Electronics Lab, University of Kassel, Kassel,
More informationSERDES High-Speed I/O Implementation
SERDES High-Speed I/O Implementation FTF-NET-F0141 Jon Burnett Digital Networking Hardware A R P. 2 0 1 4 External Use Overview SerDes Background TX Equalization RX Equalization TX/RX Equalization optimization
More informationCHAPTER 4. Practical Design
CHAPTER 4 Practical Design The results in Chapter 3 indicate that the 2-D CCS TL can be used to synthesize a wider range of characteristic impedance, flatten propagation characteristics, and place passive
More informationHigh-frequency transmission line transitions
High-frequency transmission line transitions Leonard T. Hall a,b,hedleyj.hansen a,b,c, and Derek Abbott a,b a Centre for Biomedical Engineering, The University of Adelaide, SA 55 Australia b Department
More informationPCB Material Selection for High-speed Digital Designs. Add a subtitle
PCB Material Selection for High-speed Digital Designs Add a subtitle Outline Printed Circuit Boards (PCBs) for Highspeed Digital (HSD) applications PCB factors that limit High-speed Digital performance
More informationKeysight Technologies In-Fixture Measurements Using Vector Network Analyzers. Application Note
Keysight Technologies In-Fixture Measurements Using Vector Network Analyzers Application Note Introduction This application note describes the use of vector network analyzers when making measurements of
More informationKeysight Technologies Signal Integrity Tips and Techniques Using TDR, VNA and Modeling
Keysight Technologies Signal Integrity Tips and Techniques Using, VNA and Modeling Article Reprint This article first appeared in the March 216 edition of Microwave Journal. Reprinted with kind permission
More information3680 Series. Universal Test Fixtures. A Complete Measurement Solution. DC to 60 GHz DC to 20 GHz 3680K DC to 40 GHz 3680V DC to 60 GHz
3680 Series Universal Test Fixtures DC to 60 GHz A Complete Measurement Solution 3680-20 DC to 20 GHz 3680K DC to 40 GHz 3680V DC to 60 GHz Solid ground contacts top and bottom allow microstrip or coplanar
More informationECE 145A and 218A. Transmission-line properties, impedance-matching exercises
ECE 145A and 218A. Transmission-line properties, impedance-matching exercises Problem #1 This is a circuit file to study a transmission line. The 2 resistors are included to allow easy disconnection of
More informationSignal Integrity Testing with a Vector Network Analyzer. Neil Jarvis Applications Engineer
Signal Integrity Testing with a Vector Network Analyzer Neil Jarvis Applications Engineer 1 Agenda RF Connectors A significant factor in repeatability and accuracy Selecting the best of several types for
More informationALMA MEMO #360 Design of Sideband Separation SIS Mixer for 3 mm Band
ALMA MEMO #360 Design of Sideband Separation SIS Mixer for 3 mm Band V. Vassilev and V. Belitsky Onsala Space Observatory, Chalmers University of Technology ABSTRACT As a part of Onsala development of
More informationTaking the Mystery out of Signal Integrity
Slide - 1 Jan 2002 Taking the Mystery out of Signal Integrity Dr. Eric Bogatin, CTO, GigaTest Labs Signal Integrity Engineering and Training 134 S. Wolfe Rd Sunnyvale, CA 94086 408-524-2700 www.gigatest.com
More informationHow Long is Too Long? A Via Stub Electrical Performance Study
How Long is Too Long? A Via Stub Electrical Performance Study Michael Rowlands, Endicott Interconnect Michael.rowlands@eitny.com, 607.755.5143 Jianzhuang Huang, Endicott Interconnect 1 Abstract As signal
More informationEvaluation of Package Properties for RF BJTs
Application Note Evaluation of Package Properties for RF BJTs Overview EDA simulation software streamlines the development of digital and analog circuits from definition of concept and estimation of required
More informationLecture 2: Signals and Transmission Lines
Slide -1 Lecture 2: Signals and Transmission Lines Prof Eric Bogatin Signal Integrity Evangelist Teledyne LeCroy www.bethesignal.com Spring 2014 Jan 2014 Slide -2 Schedule 1. Jan 13: Welcome and intro
More informationA WIDEBAND RECTANGULAR MICROSTRIP ANTENNA WITH CAPACITIVE FEEDING
A WIDEBAND RECTANGULAR MICROSTRIP ANTENNA WITH CAPACITIVE FEEDING Hind S. Hussain Department of Physics, College of Science, Al-Nahrain University, Baghdad, Iraq E-Mail: hindalrawi@yahoo.com ABSTRACT A
More informationElectromagnetic Analysis of Decoupling Capacitor Mounting Structures with Simbeor
Simbeor Application Note #2008_01, March 2008 2008 Simberian Inc. Electromagnetic Analysis of Decoupling Capacitor Mounting Structures with Simbeor Simberian, Inc. www.simberian.com Simbeor: Easy-to-Use,
More informationELC 4383 RF/Microwave Circuits I Laboratory 4: Quarter-Wave Impedance Matching Network
1 ELC 4383 RF/Microwave Circuits I Laboratory 4: Quarter-Wave Impedance Matching Network Note: This lab procedure has been adapted from a procedure written by Dr. Larry Dunleavy and Dr. Tom Weller at the
More informationHMC728LC3C HIGH SPEED LOGIC - SMT. Typical Applications. Features. Functional Diagram. General Description
Typical Applications Features The HMC728LC3C is ideal for: 2:1 Multiplexer up to 14 Gbps RF ATE Applications Broadband Test & Measurement Serial Data Transmission up to 14 Gbps Redundant Path Switching
More informationDesignCon Design of Gb/s Interconnect for High-bandwidth FPGAs. Sherri Azgomi, Altera Corporation
DesignCon 2004 Design of 3.125 Gb/s Interconnect for High-bandwidth FPGAs Sherri Azgomi, Altera Corporation sazgomi@altera.com Lawrence Williams, Ph.D., Ansoft Corporation williams@ansoft.com CF-031505-1.0
More informationPRELIMINARY PRELIMINARY
Impedance Discontinuities of Right Angle Bends 90 degree, chamfered, and radial Augusto Panella Molex Incorporated Scott McMorrow SiQual, Inc. Introduction The results presented below are a portion of
More informationDifferential Signaling is the Opiate of the Masses
Differential Signaling is the Opiate of the Masses Sam Connor Distinguished Lecturer for the IEEE EMC Society 2012-13 IBM Systems & Technology Group, Research Triangle Park, NC My Background BSEE, University
More informationStudent Research & Creative Works
Scholars' Mine Masters Theses Student Research & Creative Works Summer 2010 Time-domain thru-reflect-line (TRL) calibration error assessment and its mitigation and modeling of multilayer printed circuit
More informationDesignCon Differential PCB Structures using Measured TRL Calibration and Simulated Structure De-Embedding
DesignCon 2007 Differential PCB Structures using Measured TRL Calibration and Simulated Structure De-Embedding Heidi Barnes, Verigy, Inc. heidi.barnes@verigy.com Dr. Antonio Ciccomancini, CST of America,
More informationBroadband Microstrip band pass filters using triple-mode resonator
Broadband Microstrip band pass filters using triple-mode resonator CH.M.S.Chaitanya (07548), M.Tech (CEDT) Abstract: A broadband microstrip band pass filter using a triple-mode resonator is presented.
More informationHigh-Speed Circuit Board Signal Integrity
High-Speed Circuit Board Signal Integrity For a listing of recent titles in the Artech House Microwave Library, turn to the back of this book. High-Speed Circuit Board Signal Integrity Stephen C. Thierauf
More informationLENGTH REDUCTION OF EVANESCENT-MODE RIDGE WAVEGUIDE BANDPASS FILTERS
Progress In Electromagnetics Research, PIER 40, 71 90, 2003 LENGTH REDUCTION OF EVANESCENT-MODE RIDGE WAVEGUIDE BANDPASS FILTERS T. Shen Advanced Development Group Hughes Network Systems Germantown, MD
More informationECE 145A/218A, Lab Project #1a: passive Component Test.
ECE 145A/218A, Lab Project #1a: passive Component Test. September 28, 2017 OVERVIEW... 2 GOALS:... 2 PRECAUTIONS TO AVOID INSTRUMENT DAMAGE... 2 SAFETY PRECAUTIONS... 2 READING:... 3 NETWORK ANALYZER CALIBRATION...
More informationCHAPTER 3 DEVELOPMENT OF UWB BANDPASS FILTERS
33 CHAPTER 3 DEVELOPMENT OF UWB BANDPASS FILTERS 3.1 INTRODUCTION As discussed in the first chapter under the sub-section literature review, development of Bandpass Filters (BPFs) for UWB systems have
More informationPractical Design Considerations for Dense, High-Speed, Differential Stripline PCB Routing Related to Bends, Meanders and Jog-outs
Practical Design Considerations for Dense, High-Speed, Differential Stripline PCB Routing Related to Bends, Meanders and Jog-outs AUTHORS Michael J. Degerstrom, Mayo Clinic degerstrom.michael@mayo.edu
More informationAntenna Matching Within an Enclosure Part II: Practical Techniques and Guidelines
Antenna Matching Within an Enclosure Part II: Practical Techniques and Guidelines By Johnny Lienau, RF Engineer June 2012 Antenna selection and placement can be a difficult task, and the challenges of
More informationDesign and Characterization of a Micro-Strip RF Anode for Large- Area based Photodetectors Orsay- Friday, June Hervé Grabas UChicago / CEA
Design and Characterization of a Micro-Strip RF Anode for Large- Area based Photodetectors Orsay- Friday, June 15. 2012 Hervé Grabas UChicago / CEA Saclay Irfu. Outline Introduction Precise timing in physics
More informationDESIGN OF SEVERAL POWER DIVIDERS USING CPW- TO-MICROSTRIP TRANSITION
Progress In Electromagnetics Research Letters, Vol. 41, 125 134, 2013 DESIGN OF SEVERAL POWER DIVIDERS USING CPW- TO-MICROSTRIP TRANSITION Maoze Wang *, Fushun Zhang, Jian Sun, Ke Chen, and Bin Wen National
More informationPCB Dielectric Material Selection and Fiber Weave Effect on High-Speed Channel Routing. Introduction
PCB Dielectric Material Selection and Fiber Weave Effect on High-Speed Channel Routing May 2008, v1.0 Application Note 528 Introduction As data rates increase, designers are increasingly moving away from
More informationHigh Speed Characterization Report
LSHM-150-06.0-L-DV-A Mates with LSHM-150-06.0-L-DV-A Description: High Speed Hermaphroditic Strip Vertical Surface Mount, 0.5mm (.0197") Centerline, 12.0mm Board-to-Board Stack Height Samtec, Inc. 2005
More informationWideband Low-Reflection Transmission Lines for Bare Chip on Multilayer PCB
Wideband Low-Reflection Transmission Lines for Bare Chip on Multilayer PCB Rashad Ramzan, Jonas Fritzin, Jerzy Dabrowski, and Christer Svensson The pad pitch of modern radio frequency integrated circuits
More informationCustom Interconnects Fuzz Button with Hardhat Test Socket/Interposer 1.00 mm pitch
Custom Interconnects Fuzz Button with Hardhat Test Socket/Interposer 1.00 mm pitch Measurement and Model Results prepared by Gert Hohenwarter 12/14/2015 1 Table of Contents TABLE OF CONTENTS...2 OBJECTIVE...
More informationDesign and experimental realization of the chirped microstrip line
Chapter 4 Design and experimental realization of the chirped microstrip line 4.1. Introduction In chapter 2 it has been shown that by using a microstrip line, uniform insertion losses A 0 (ω) and linear
More informationapplication In-Fixture Measurements Using Vector Network Analyzers Network Analysis Solutions Application Note
application Network Analysis Solutions In-Fixture Measurements Using Vector Network Analyzers Application Note 1287-9 Table of contents Introduction..................................................3 The
More informationAries CSP microstrip socket Cycling test
Aries CSP microstrip socket Cycling test RF Measurement Results prepared by Gert Hohenwarter 2/18/05 1 Table of Contents TABLE OF CONTENTS... 2 OBJECTIVE... 3 METHODOLOGY... 3 Test procedures... 6 Setup...
More informationThe Challenges of Differential Bus Design
The Challenges of Differential Bus Design February 20, 2002 presented by: Arthur Fraser TechKnowledge Page 1 Introduction Background Historically, differential interconnects were often twisted wire pairs
More informationLambert Simonovich 5/28/2012
Guard Traces White Paper-Issue 02 Lambert Simonovich 5/28/2012 Abstract: To guard or not to guard? That is the question often asked by digital hardware design engineers. As bit rates continue to climb,
More informationMultilayer VIA simulations using ADS Anurag Bhargava, Application Consultant, Agilent EEsof EDA, Agilent Technologies
Multilayer VIA simulations using ADS Anurag Bhargava, Application Consultant, Agilent EEsof EDA, Agilent Technologies Many a time designers find themselves in pretty confusing start when it comes to simulating
More informationMICTOR. High-Speed Stacking Connector
MICTOR High-Speed Stacking Connector Electrical Performance Report for the 0.260" (6.6-mm) Stack Height Connector.......... Connector With Typical Footprint................... Connector in a System Report
More informationSET2DIL: Method to Derive Differential Insertion Loss from Single- Ended TDR/TDT Measurements
DESIGNCON 2010 : Method to Derive Differential Insertion Loss from Single- Ended TDR/TDT Measurements Jeff Loyer, Intel Corp. Jeff.Loyer@intel.com Richard Kunze, Intel Corp. Richard.K.Kunze@Intel.com ABSTRACT
More informationOptically reconfigurable balanced dipole antenna
Loughborough University Institutional Repository Optically reconfigurable balanced dipole antenna This item was submitted to Loughborough University's Institutional Repository by the/an author. Citation:
More information