STA501 40V 3.5A DOUBLE POWER HALF BRIDGE
|
|
|
- Patrick Benson
- 5 years ago
- Views:
Transcription
1 40V 3.5A DOUBLE POWER HALF BRIDGE MINIMUM INPUT OUTPUT PULSE WIDTH DISTORTION 200mΩ R dson COMPLEMENTARY DMOS OUTPUT STAGE CMOS COMPATIBLE LOGIC INPUTS THERMAL PROTECTION THERMAL WARNING OUTPUT UNDER VOLTAGE PROTECTION DESCRIPTION STA501 is a monolithic dual half bridge stage in Multipower BCD Technology. The device is particularly designed to make the output stage of a mono All-Digital High Efficiency AUDIO APPLICATION CIRCUIT +3.3V TH_WAR R57 10K C58 PWRDN R59 10K C58 C53 C60 IBIAS CONFIG PWRDN FAULT TRI-STATE TH_WAR V DD V DD V SS V SS SIGN SIGN -Reg -Clean SUB PROTECTIONS & LOGIC REGULATORS M17 M15 M16 M14 PowerSO36 ORDERING NUMBER: STA501 (DDX ) amplifier capable to deliver THD = 10% at V cc 30V output power on 8Ω load. The input pins have threshold proportional to Ibias pin voltage MULTIPOWER BCD TECHNOLOGY C30 1µF B A A B B C32 1µF C31 1µF C33 1µF R C µF L113 22µH C110 C pF R103 6 R102 6 C111 L112 22µH D02AU1447 C107 C nF C106 December /8
2 PIN FUNCTION N Pin Description 1 -SUB Substrate ground 35 ; 36 Vcc Sign Signal Positive Supply 15 Vcc Positive Supply 12 Vcc Positive Supply 7 Vcc Positive Supply 4 Vcc Positive Supply 14 Negative Supply 13 Negative Supply 6 Negative Supply 5 Negative Supply 16 ; ; 11 8 ; 9 Output half bridge 2 ; 3 Output half bridge Input of half bridge 32 Input of half bridge 21 ; 22 Vdd 5V Regulator referred to ground 33 ; 34 Vss 5V Regulator referred to +Vcc 25 PWRDN Stand-by pin 26 TRI-STATE Hi-Z pin 27 FAULT Fault pin advisor TH-WAR Thermal warning advisor 19 -clean Logical ground 23 IBIAS High logical state setting voltage 18 NC Not connected 20 -Reg Ground for regulator Vdd 2/8
3 FUNCTIONAL PIN STATUS PIN NAME Logical value IC -STATUS FAULT 0 Fault detected (Short circuit, or Thermal..) FAULT * 1 Normal Operation TRI-STATE 0 All powers in Hi-Z state TRI-STATE 1 Normal operation PWRDN 0 Low absorpion PWRDN 1 Normal operation THWAR 0 Temperature of the IC =130C THWAR* 1 Normal operation * : The pin is open collector. To have the high logic value, it needs to be pulled up by a resistor. PIN CONNECTION Sign Sign V SS V SS TH_WAR FAULT TRI-STATE PWRDN IBIAS V DD V DD -Reg -Clean SUB D02AU N.C 3/8
4 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit V CE DC Supply Voltage (Pin 4,7,12,15) 40 V V max Maximum Voltage on pins 23 to V T op Operating Temperature Range 0 to 70 C T stg, T j Storage and Junction Temperature -40 to 150 C THERMAL DATA Symbol Parameter Min. Typ. Max. Unit T j-case Thermal Resistance Junction to Case (thermal pad) 2.5 C/W T jsd Thermal shut-down junction temperature 150 C T warn Thermal warning temperature 130 C t hsd Thermal shut-down hysteresis 25 C ELECTRICAL CHARACTERISTCS (Ibias = 3.3V; Vcc = 30V; T amb = 25 C unless otherwise specified) Symbol Parameter Test conditions Min. Typ. Max. Unit R dson I dss g N g P Power Pchannel/Nchannel MOSFET RdsON Power Pchannel/Nchannel leakage Idss Power Pchannel RdsON Matching Power Nchannel RdsON Matching Id=1A mω Vcc=35V 50 µa Id=1A 95 % Id=1A 95 % Dt_s Low current Dead Time (static) see test circuit no.1; see fig ns Dt_d High current Dead Time (dinamic) L=22µH; C = 470nF; Rl = 8 Ω Id=3.5A; see fig ns t d ON Turn-on delay time Resistive load 100 ns t d OFF Turn-off delay time Resistive load 100 ns t r Rise time Resistive load 25 ns t f Fall time Resistive load; as fig ns Supply voltage operating voltage V V IN-H High level input voltage Ibias/2 +300mV V V IN-L Low level input voltage Ibias/2-300mV V I IN-H Hi level Input current Pin voltage = Ibias 1 µa 4/8
5 ELECTRICAL CHARACTERISTCS (continued) Symbol Parameter Test conditions Min. Typ. Max. Unit I IN-L Low level input current Pin voltage = 0.3V 1 µa I PWRDN-H Hi level PWRDN pin input current Ibias = 3.3V 35 µa V L V H I VCC- PWRDN Low logical state voltage VL (pin PWRDN, TRISTATE) (note 1) High logical state voltage VH (pin PWRDN, TRISTATE) (note 1) Supply Current from Vcc in Power Down Ibias = 3.3V 0.8 V Ibias = 3.3V 1.7 V PWRDN = 0 3 ma I FAULT I VCC-hiz I VCC I out-sh Output Current pins FAULT -TH-WARN when FAULT CONDITIONS Supply current from Vcc in Tristate Supply current from Vcc in operation (both channel switching) Overcurrent protection threshold (short circuit current limit) Notes: 1. The following table explains the VL, VH variation with Ibias LOGIC TRUTH TABLE (see fig. 2) Vpin = 3.3V 1 ma Vcc=30V; Tri-state=0 22 ma Input pulse width = 50% Duty; Switching Frequency = 384Khz; No LC filters; 50 ma A V UV Undervoltage protection threshold 7 V t pw-min Output minimum pulse width No Load ns Ibias VLmin VHmax Unit V V V TRI-STATE Q1 Q2 Q3 Q4 OUTPUT MODE 0 x x OFF OFF OFF OFF Hi-Z OFF OFF ON ON DUMP OFF ON ON OFF NEGATIVE ON OFF OFF ON POSITIVE ON ON OFF OFF Not used 5/8
6 Figure 1. Test Circuit. OUTY Vcc Low current dead time = MAX(DTr,DTf) +Vcc (3/4)Vcc (1/2)Vcc (1/4)Vcc Figure 2. Figure 3. Duty cycle=a Duty cycle = 50% INY M58 M57 gnd OUTY DTin(A) Q1 Q3 + Q2 Q4 DTr R 8Ω D02AU1450 DTf + - V67 = vdc = Vcc/2 t D02AU1448 High Current Dead time for Bridge application = ABS(DTout(A)-DTin(A))+ABS(DTOUT(B)-DTin(B)) + M58 M57 Q1 Q3 DTout(A) L67 22µ Iout=3.5A C69 470nF Rload=8Ω C71 470nF C70 470nF DTout(B) L68 22µ Iout=3.5A Q2 Q4 M64 M63 Duty cycle=b DTin(B) Duty cycle A and B: Fixed to have DC output current of 3.5A in the direction shown in figure D02AU1451 6/8
7 DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A A A A a b c D D D E E E E E e e G H h L N 10 (max) s 8 (max) (1) D and E1 do not include mold flash or protusions. Mold flash or protusions shall not exceed 0.15mm (0.006 ) (2) No intrusion allowed inwards the leads. OUTLINE AND MECHANICAL DATA PowerSO36 (SLUG UP) /8
8 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners 2003 STMicroelectronics - All rights reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States 8/8
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) STA501A 45V 3.5A DOUBLE POWER HALF BRIDGE 1 FEATURES 2 DESCRIPTION
45V 3.5A DOUBLE POWER HALF BRIDGE 1 FEATURES MULTIPOWER BCD TECHNOLOGY MINIMUM INPUT OUTPUT PULSE WIDTH DISTORTION 200mΩ R dson COMPLEMENTARY DMOS OUTPUT STAGE CMOS COMPATIBLE LOGIC INPUTS THERMAL PROTECTION
Figure 1. Package. Table 1. Order Codes V CC 1A C30 OUT1A OUT1A GND1A V CC1B C31 OUT1B OUT1B M4 13 GND1B 22 V SS REGULATORS 7 V CC2A C32 M17 OUT2A
40V 3.5A QUAD POWER HALF BRIDGE 1 FEATURES MULTIPOWER BCD TECHNOLOGY MINIMUM INPUT OUTPUT PULSE WIDTH DISTORTION 0mΩ R dson COMPLEMENTARY DMOS OUTPUT STAGE CMOS COMPATIBLE LOGIC INPUTS THERMAL PROTECTION
STA517B. 60 V 6 A quad power half bridge. Features. Description
0 V A quad power half bridge Features Minimum input output pulse width distortion 0 mω R dson complementary DMOS output stage CMOS compatible logic inputs Thermal protection Thermal warning output Under
Order code Operating temp. range Package Packing. STA510F 0 to 70 C PowerSSO36 (slug up) Tube STA510FTR 0 to 70 C PowerSSO36 (slug up) Tape & Reel
44-V, 5.5-A, quad power half-bridge Features Minimum input/output pulse width distortion 150 mω R dson complementary DMOS output stage CMOS compatible logic inputs Thermal protection Thermal warning output
STA506 40V 4A QUAD POWER HALF BRIDGE
40V 4A QUAD POWER HALF BRIDGE FEATURES MINIMUM INPUT OUTPUT PULSE WIDTH DISTORTION 0mΩ R dson COMPLEMENTARY DMOS OUTPUT STAGE CMOS COMPATIBLE LOGIC INPUTS THERMAL PROTECTION THERMAL WARNING OUTPUT UNDER
Order code Temperature range Package Packaging. STA517B 0 to 70 C PowerSO36 EPU Tube STA517B13TR 0 to 70 C PowerSO36 EPU Tape and reel
0-V.5-A quad power half bridge Features Low input/output pulse width distortion 0 mω R dson complementary DMOS output stage CMOS-compatible logic inputs Thermal protection Thermal warning output Undervoltage
STA V 3.5A quad power half bridge. Feature. Description. Order codes
40V 3.5A quad power half bridge Feature Multipower BCD technology Minimum input output pulse width distortion 0mΩ R dson complementary dmos output stage CMOS compatible logic inputs Thermal protection
Description. Table 1. Device summary. Order code Ambient temp. range Package Packaging. STA515W13TR 0 to 70 C PowerSSO36 EPD Tape and reel
40 V, 3 A, quad power half bridge Description Datasheet - production data Features Multipower BCD technology Low input/output pulse width distortion 0 m R dson complementary DMOS output stage CMOS-compatible
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) TDA7297D 10W+10W DUAL BRIDGE AMPLIFIER 1 FEATURES 2 DESCRIPTION
0W0W DUAL BRIDGE AMPLIFIER FEATURES TECHNOLOGY BI0II WIDE SUPPLY VOLTAGE RANGE (6. 8V) OUTPUT POWER 00W @ THD = 0%, R L = 8Ω, V CC = 3V MINIMUM EXTERNAL COMPONENTS NO SVR CAPACITOR NO BOOTSTRAP NO BOUCHEROT
TDA W MONO CLASS-D AMPLIFIER 1 FEATURES 2 DESCRIPTION. Figure 1. Package 25W OUTPUT POWER:
25 MONO CLASS-D AMPLIFIER 1 FEATURES 25 OUTPUT POER: RL = 8Ω/4Ω; THD = 10% HIGH EFFICIENCY IDE SUPPLY VOLTAGE RANGE (UP TO ±25V) SPLIT SUPPLY OVERVOLTAGEPROTECTION ST-BY AND MUTE FEATURES SHORT CIRCUIT
TDA W MONO CLASS-D AMPLIFIER 18W OUTPUT POWER:
TDA481 18 MONO CLASS-D AMPLIFIER 18 OUTPUT POER: RL = 8Ω/4Ω; THD = 10% HIGH EFFICIENCY IDE SUPPLY VOLTAGE RANGE (UP TO ±25V) SPLIT SUPPLY OVERVOLTAGE PROTECTION ST-BY AND MUTE FEATURES SHORT CIRCUIT PROTECTION
Obsolete Product(s) - Obsolete Product(s)
FEATURES 0 + 0 OUTPUT POER: @R L = 8Ω/4Ω; THD = 0% HIGH EFFICIENCY IDE SUPPLY VOLTAGE RANGE (FROM ±0 TO ±V) SPLIT SUPPLY, SINGLE SUPPLY OPERATION TURN OFF/ON POP FREE ST-BY AND MUTE FEATURES SHORT CIRCUIT
TDA7231A 1.6W AUDIO AMPLIFIER OPERATING VOLTAGE 1.8 TO 15 V LOW QUIESCENT CURRENT HIGH POWER CAPABILITY LOW CROSSOVER DISTORTION SOFT CLIPPING
1.6 AUDIO AMPLIFIER OPERATING VOLTAGE 1.8 TO 15 V LO QUIESCENT CURRENT. HIGH POER CAPABILITY LO CROSSOVER DISTORTION SOFT CLIPPING DESCRIPTION The is a monolithic integrated circuit in 4 + 4 lead minidip
Order code Temperature range Package Packaging. STA516B 0 to 90 C PowerSO36 EPU Tube STA516B13TR 0 to 90 C PowerSO36 EPU Tape and reel
STA51B 5-volt, 7.5-amp, quad power half bridge Features! Low input/output pulse-width distortion! 0 mω R dson complementary DMOS output stage! CMOS-compatible logic inputs! Thermal protection! Thermal
TSM100 SINGLE OPERATIONAL AMPLIFIER AND SINGLE COMPARATOR
OPERATIONAL AMPLIFIER LOW INPUT OFFSET VOLTAGE : 0.5 typ. MEDIUM BANDWIDTH (unity gain) : 0.9MHz LARGE OUTPUT VOLTAGE SWING : 0V to (V CC - 1.5V) INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND WIDE POWER
L9686D AUTOMOTIVE DIRECTION INDICATOR
L9686 AUTOMOTIVE DIRECTION INDICATOR RELAY DRIVER IN CAR DIRECTION INDICATORS FLASH FREQUENCY DOUBLES TO INDI- CATE LAMP FAILURE DUMP PROTECTION ( ± 80 V) REVERSE BATTERY PROTECTION DESCRIPTION The L9686
STA516BE. 500 W FFX digital amplifier power stage. Applications. Description. Features
STA51BE 500 W FFX digital amplifier power stage Datasheet - production data EMI compliant when used with recommended system design Automatic recovery mode after fault conditions Applications Home theater
Table 1. Order Codes Vref
FEATURES TECHNOLOGY BI20II WIDE SUPPLY VOLTAGE RANGE (3. 2V) OUTPUT POWER: 33W @THD = %, R L = 8Ω, V CC = 7.V 44W Music Power @THD = %, R L = 8Ω, V CC = 8.V SINGLE SUPPLY MINIMUM EXTERNAL COMPONENTS: NO
TDA7241B 20W BRIDGE AMPLIFIER FOR CAR RADIO
TDA7241B 20W BRIDGE AMPLIFIER FOR CAR RADIO VERY LOW STAND-BY CURRENT GAIN = 32dB OUTPUT PROTECTED AGAINST SHORT CIRCUITS TO GROUND AND ACROSS LOAD COMPACT HEPTAWATT PACKAGE DUMP TRANSIENT THERMAL SHUTDOWN
L6925D HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR 1 FEATURES 2 DESCRIPTION. Figure 1. Package
HIGH EFFICIENCY MONOLITHIC SYNCHRONOUS STEP DOWN REGULATOR 1 FEATURES 2.7V TO 5.5V BATTERY INPUT RANGE HIGH EFFICIENCY: UP TO 95% INTERNAL SYNCHRONOUS SWITCH NO EXTERNAL SCHOTTKY REQUIRED EXTREMELY LOW
ST755 ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS
ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS 2.7V TO 11V INPUT TO ADJUSTABLE NEGATIVE OUTPUT CONVERSION 1W GUARANTEED OUTPUT POWER (V I >4.5V,T 70 C) 68% TYP. EFFICENCY AT 6V VERY LOW
74VHC20 DUAL 4-INPUT NAND GATE
DUAL 4-INPUT NAND GATE HIGH SPEED: t PD = 3.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
L9305A DUAL HIGH CURRENT RELAY DRIVER
L9305A DUAL HIGH CURRENT RELAY DRIVER. HIGH OUTPUT CURRENT HYSTERESIS INPUT COMPARATOR WITH WIDE RANGE COMMON MODE OPERATION AND GROUND COMPATIBLE INPUTS INPUT COMPARATOR HYSTERESIS INTERNAL THERMAL PROTECTION
NE556 SA556 - SE556 GENERAL PURPOSE DUAL BIPOLAR TIMERS
NE556 SA556 - SE556 GENERAL PURPOSE DUAL BIPOLAR TIMERS LOW TURN OFF TIME MAXIMUM OPERATING FREQUENCY GREATER THAN 500kHz TIMING FROM MICROSECONDS TO HOURS OPERATES IN BOTH ASTABLE AND MONOSTABLE MODES
Order code Temperature range Package Packaging. STA533WF 0 to 70 C PowerSSO36 EPD Tube STA533WF13TR 0 to 70 C PowerSSO36 EPD Tape and reel
18-volt, 3-amp, quad power half-bridge Features Multipower BCD technology Low input/output pulse width distortion 200-mΩ R dson complementary DMOS output stage CMOS-compatible logic inputs Thermal protection
Obsolete Product(s) - Obsolete Product(s)
DMOS DUAL FULL BRIDGE DRIVER SUPPLY VOLTAGE UP TO 48V R DS(ON) 1.2Ω L6204 (25 C) CROSS CONDUCTION PROTECTION THERMAL SHUTDOWN 0.5A DC CURRENT TTL/CMOS COMPATIBLE DRIVER HIGH EFFICIENCY CHOPPING MULTIPOWER
TDA x 40W QUAD BRIDGE CAR RADIO AMPLIFIER
TDA7386 4 x 40W QUAD BRIDGE CAR RADIO AMPLIFIER HIGH OUTPUT POWER CAPABILITY: 4 x 45W/4Ω MAX. 4 x 40W/4Ω EIAJ 4 x 28W/4Ω @ 14.4V, 1KHz, 10% 4 x 24W/4Ω @ 13.2V, 1KHz, 10% LOW DISTORTION LOW OUTPUT NOISE
Obsolete Product(s) - Obsolete Product(s)
TDA7263 12 +12W STEREO AMPLIFIER WITH MUTING WIDE SUPPLY VOLTAGE RANGE HIGH OUTPUT POWER 12+12W @ VS=28V, RL = 8Ω, THD=10% MUTE FACILITY (POP FREE) WITH LOW CONSUMPTION AC SHORT CIRCUIT PROTECTION THERMAL
Obsolete Product(s) - Obsolete Product(s)
TRIPLE 3-INPUT NOR GATE HIGH SPEED: t PD = 4.1 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
L165 3A POWER OPERATIONAL AMPLIFIER
3A POWER OPERATIONAL AMPLIFIER OUTPUT CURRENT UP TO 3A LARGE COMMON-MODE AND DIFFERENTIAL MODE RANGES SOA PROTECTION THERMAL PROTECTION ± 18V SUPPLY DESCRIPTION The L165 is a monolithic integrated circuit
74LX1G132CTR SINGLE 2-INPUT SCHMITT NAND GATE
SINGLE 2-INPUT SCHMITT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 5.5ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C TYPICAL HYSTERESIS: V h =1V at V CC =4.5V POWER DOWN PROTECTION
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIVE OR GATE MEDIUM-SPEED OPERATION t PHL =t PLH = 70ns (Typ.) at CL = 50 pf and V DD = 10V QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V AND 15V PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I
Obsolete Product(s) - Obsolete Product(s)
SINGLE SCHMITT INERTER HIGH SPEED: t PD = 4.3ns (TYP.) at CC =5 LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C TYPICAL HYSTERESIS: h =1 at CC =4.5 POWER DOWN PROTECTION ON INPUT SYMMETRICAL OUTPUT
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) STG3684
LOW VOLTAGE 0.5Ω MAX DUAL SPDT SWITCH WITH BREAK BEFORE MAKE FEATURE HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 3.0V t PD = 0.4ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
TDA0161. Proximity Detectors. Features. Description. Block Diagram. 10mA Output Current Oscillator Frequency 10MHz Supply Voltage +4 to +35V
Proximity Detectors Features 10mA Output Current Oscillator Frequency 10MHz Supply Voltage +4 to +35V Description These monolithic integrated circuits are designed for metallic body detection by sensing
STSR30 SYNCHRONOUS RECTIFIER SMART DRIVER FOR FLYBACK
SYNCHRONOUS RECTIFIER SMART DRIVER FOR FLYBACK SUPPLY VOLTAGE RANGE: 4V TO 5.5V TYPICAL PEAK OUTPUT CURRENT: (SOURCE-SINK: 1.5A) OPERATING FREQUENCY: 20 TO 500 KHz INHIBIT BLANKING TIME: 700 ns AUTOMATIC
74VHC132 QUAD 2-INPUT SCHMITT NAND GATE
QUAD 2-INPUT SCHMITT NAND GATE HIGH SPEED: t PD = 3.9 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C TYPICAL HYSTERESIS: V h = 1V at V CC = 4.5V POWER DOWN PROTECTION ON
Obsolete Product(s) - Obsolete Product(s)
SINGLE INVERTER (OPEN DRAIN) HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
HCF4585B 4-BIT MAGNITUDE COMPARATOR
4-BIT MAGNITUDE COMPARATOR EXPANSION TO 8, 12, 16...4 N BITS BY CASCADING UNIT MEDIUM SPEED OPERATION : COMPARES TWO 4-BIT WORDS IN 180ns (Typ.) at 10V STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT
74VHC08 QUAD 2-INPUT AND GATE
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
Obsolete Product(s) - Obsolete Product(s)
LOW-NOISE VERTICAL DEFLECTION SYSTEM FEATURES SUMMARY COMPLETE VERTICAL DEFLECTION SYSTEM LOW NOISE SUITABLE FOR HIGH DEFINITION MONITORS ESD PROTECTED DESCRIPTION The TDA75P is a monolithic integrated
ADJUSTABLE AND +3.3 V DUAL VOLTAGE REGULATOR WITH DISABLE AND RESET FUNCTIONS RESET DELAY CAPACITOR. September /12
STV810AD ADJUSTABLE AND +. V DUAL VOLTAGE REGULATOR WITH DISABLE AND FUNCTIONS FEATURES Input Voltage Range: 5 V to 18 V Output Currents up to 750 ma Fixed Precision Output 1 Voltage:. V ±2% Adjustable
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.7 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
HCF4072B DUAL 4 INPUT OR GATE
DUAL 4 INPUT OR GATE MEDIUM SPEED OPERATION : t PD = 60ns (TYP.) at DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A =
R K R4 130K C23. PWM-stage1 OSC. PWM-stage2. C9 470pF C28 R9 52.3K
TDA7490 + STRO CLASS-D AMPLIFIR 0 MONO IN BTL PRODUCT PRVI + OUTPUT POR: RL = 8Ω/4Ω; THD = 0% HIGH FFICINCY ID SUPPLY VOLTAG RANG (FROM ±0 TO ±V) SPLIT SUPPLY TURN OFF/ON POP FR ST-BY AND MUT FATURS SHORT
HCF4050B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME : t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION HIGH "SINK" AND "SOURCE" CURRENT CAPABILITY QUIESCENT CURRENT
STG719 LOW VOLTAGE 4Ω SPDT SWITCH
LOW VOLTAGE 4Ω SPDT SWITCH HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 5V t PD = 0.4ns (TYP.) at V CC = 3.3V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C LOW "ON" RESISTANCE: R ON = 4Ω (MAX. T A
LOW VOLTAGE TONE CONTROL DIGITALLY CONTROLLED AUDIO PROCESSOR 5.6K. C14 3.3nF BASSO-R BASSO-L. 0/-10dB x1 x5 TREBLE BASS
LOW VOLTAGE TONE CONTROL DIGITALLY CONTROLLED AUDIO PROCESSOR 1 FEATURES 2 STEREO INPUT 1 STEREO OUTPUT TREBLE BOOST BASS CONTROL BASS AUTOMATIC LEVEL CONTROL VOLUME CONTROL IN 1dB STEPS MUTE STAND-BY
74VHCT00ATTR QUAD 2-INPUT NAND GATE
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 5 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
STS7PF30L P-CHANNEL 30V Ω - 7A - SO-8 STripFET II Power MOSFET General features Description Internal schematic diagram
P-CHANNEL 30V - 0.16Ω - 7A - SO-8 STripFET II Power MOSFET General features Type V DSS R DS(on) I D STS7PF30L 30V
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NOR GATE HIGH SPEED: t PD = 3.6ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.7ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT
HCF40107B DUAL 2-INPUT NAND BUFFER/DRIVER
DUAL 2-INPUT NAND BUFFER/DRIVER 32 TIMES STANDARD B-SERIES OUTPUT CURRENT DRIVE SINKING CAPABILITY - 136 ma TYP. AT V DD = 10V, V DS = 1V QUIESCENT CURRENT SPECIF. UP TO 20V 5V, 10V AND 15V PARAMETRIC
L5973D 2.5A SWITCH STEP DOWN SWITCHING REGULATOR L5973D
.A SWITCH STEP DOWN SWITCHING REGULATOR.A INTERNAL SWITCH OPERATING INPUT VOLTAGE FROM.V TO 3V 3.3V / (±%) REFERENCE VOLTAGE PUT VOLTAGE ADJUSTABLE FROM.3V TO 3V LOW DROP OPERATION: 00% DUTY CYCLE 0KHz
74V1T00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
TDA7297SA 10W+10W DUAL BRIDGE AMPLIFIER
WW DUAL BRIDGE AMPLIFIER WIDE SUPPLY VOLTAGE RANGE (VV) MINIMUM EXTERNAL COMPONENTS NO SWR CAPACITOR NO BOOTSTRAP NO BOUCHEROT CELLS INTERNALLY FIXED GAIN STANDBY & MUTE FUNCTIONS SHORT CIRCUIT PROTECTION
74V1G00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
TDA7266SA 7W+7W DUAL BRIDGE AMPLIFIER
7W7W DUAL BRIDGE AMPLIFIER WIDE SUPPLY VOLTAGE RANGE (3.518V) MINIMUM EXTERNAL COMPONENTS NO SWR CAPACITOR NO BOOTSTRAP NO BOUCHEROT CELLS INTERNALLY FIXED GAIN STANDBY & MUTE FUNCTIONS SHORT CIRCUIT PROTECTION
TDA7297SA 10W+10W DUAL BRIDGE AMPLIFIER
WW DUAL BRIDGE AMPLIFIER WIDE SUPPLY VOLTAGE RANGE (6V18V) MINIMUM EXTERNAL COMPONENTS NO SWR CAPACITOR NO BOOTSTRAP NO BOUCHEROT CELLS INTERNALLY FIXED GAIN STANDBY & MUTE FUNCTIONS SHORT CIRCUIT PROTECTION
Obsolete Product(s) - Obsolete Product(s)
WW DUAL BRIDGE AMPLIFIER WIDE SUPPLY VOLTAGE RANGE (VV) MINIMUM EXTERNAL COMPONENTS NO SWR CAPACITOR NO BOOTSTRAP NO BOUCHEROT CELLS INTERNALLY FIXED GAIN STANDBY & MUTE FUNCTIONS SHORT CIRCUIT PROTECTION
Obsolete Product(s) - Obsolete Product(s)
7W7W DUAL BRIDGE AMPLIFIER WIDE SUPPLY VOLTAGE RANGE (3.518V) MINIMUM EXTERNAL COMPONENTS NO SWR CAPACITOR NO BOOTSTRAP NO BOUCHEROT CELLS INTERNALLY FIXED GAIN STANDBY & MUTE FUNCTIONS SHORT CIRCUIT PROTECTION
74LVX05 LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS
LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.8ns (TYP.) at V CC = 3.3V 5V TOLERANT INPUTS INPUT VOLTAGE LEVEL: V IL =0.8V, V IH =2V at V CC =3V LOW POWER DISSIPATION:
TS834 MICROPOWER VOLTAGE SUPERVISOR RESET ACTIVE LOW OR HIGH INTEGRATED TIMER
MICROPOWER VOLTAGE SUPERVISOR RESET ACTIVE LOW OR HIGH INTEGRATED TIMER ULTRA LOW POWER CONSUMPTION : 12µA max. @ V CC = 5V BOTH ACTIVE HIGH AND ACTIVE LOW OUTPUTS RESET TIMER WITH DISABLE FUNCTION PRECISION
LDRxxyy VERY LOW DROP DUAL VOLTAGE REGULATOR
VERY LOW DROP DUAL VOLTAGE REGULATOR OUTPUT CURRENT 1 UP TO 500mA OUTPUT CURRENT 2 UP TO 1.0A LOW DROPOUT VOLTAGE 1 (0.3V @ I O =500mA) LOW DROPOUT VOLTAGE 2 (0.4V @ I O =1A) VERY LOW SUPPLY CURRENT (TYP.50µA
74VHC174 HEX D-TYPE FLIP FLOP WITH CLEAR
HEX D-TYPE FLIP FLOP WITH CLEAR HIGH SPEED: f MAX = 175MHz (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION
SD1275 RF POWER BIPOLAR TRANSISTORS VHF MOBILE APPLICATIONS. FEATURES SUMMARY 160 MHz 13.6 VOLTS COMMON EMITTER P OUT = 40 W MIN.
RF POWER BIPOLAR TRANSISTORS VHF MOBILE APPLICATIONS FEATURES SUMMARY 1 MHz 13.6 VOLTS COMMON EMITTER P OUT = W MIN. WITH 9 db GAIN Figure 1. Package DESCRIPTION The SD1275 is a 13.6 V Class C epitaxial
SD1488 RF POWER BIPOLAR TRANSISTORS UHF MOBILE APPLICATIONS
RF POWER BIPOLAR TRANSISTORS UHF MOBILE APPLICATIONS FEATURES SUMMARY 470 MHz 12.5 VOLTS EFFICIENCY % COMMON EMITTER P OUT = 38 W MIN. WITH 5.8 db GAIN DESCRIPTION The SD1488 is a 12.5 V Class C epitaxial
L6571AD L6571BD HIGH VOLTAGE HALF BRIDGE DRIVER WITH OSCILLATOR
L657A L657B HIGH VOLTAGE HALF BRIDGE DRIVER WITH OSCILLATOR HIGH VOLTAGE RAIL UP TO 600V BCD OFF LINE TECHNOLOGY 5.6V ZENER CLAMP ON DRIVER CURRENT CAPABILITY: - SINK CURRENT = 270mA - SOURCE CURRENT =
TDA W AUDIO AMPLIFIER
TDA2006 12W AUDIO AMPLIFIER DESCRIPTION The TDA2006 is a monolithic integrated circuit in Pentawatt package, intended for use as a low frequency class "AB" amplifier. At ±12V, d = 10 % typically it provides
L5972D 2A SWITCH STEP DOWN SWITCHING REGULATOR L5972D
A SWITCH STEP DOWN SWITCHING REGULATOR A INTERNAL SWITCH OPERATING INPUT VOLTAGE FROM.V TO 6V PUT VOLTAGE ADJUSTABLE FROM.V TO V LOW DROP OPERATION: 00% DUTY CYCLE 0KHz INTERNALLY FIXED FREQUENCY VOLTAGE
HCF4066B QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS
QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS 15V DIGITAL OR ± 7.5V PEAK TO PEAK SWITCHING 125Ω TYPICAL ON RESISTANCE FOR 15V OPERATION SWITCH ON RESISTANCE MATCHED
DC LINE TERMINATION ACT DCT V-
L3845 TRUNK INTERFACE ON CHIP POLARITY GUARD MEETS DC LINE CHARACTERISTICS OF EITHER CCITT AND EIA RS 464 SPECS PULSE FUNCTION HIGH AC IMPEDANCE OFF HOOK-STATUS DETECTION OUTPUT LOW EXTERNAL COMPONENT
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. L6506 L6506D CURRENT CONTROLLER FOR STEPPING MOTORS DESCRIPTION The L6506/D
HCF4000B DUAL 3-INPUT NOR GATE PLUS INVERTER
DUAL 3-INPUT NOR GATE PLUS INERTER PROPAGATION DELAY TIME t PD = 50ns (TYP.) at DD = 10 C L = 50pF BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED
Obsolete Product(s) - Obsolete Product(s)
11W+11W AMPLIFIER WITH DC CONTROL 11+11W OUTPUT POWER R L = Ω @THD = % V CC = 2V ST-BY AND MUTE FUNCTIONS LOW TURN-ON TURN-OFF POP NOISE LINEAR CONTROL DC COUPLED WITH POWER OP. AMP. NO BOUCHEROT CELL
STF12PF06 P-CHANNEL 60V Ω - 12A TO-220/TO-220FP STripFET II POWER MOSFET
STP12PF06 STF12PF06 P-CHANNEL 60V - 0.18 Ω - 12A TO-220/TO-220FP STripFET II POWER MOSFET Table 1: General Features TYPE V DSS R DS(on) I D Figure 1:Package STP12PF06 STF12PF06 60 V 60 V TYPICAL R DS (on)
HCF4012B DUAL 4 INPUT NAND GATE
DUAL 4 INPUT NAND GATE PROPAGATION DELAY TIME t PD = 60ns (Typ.) at DD = 10 BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15
Non-inverting input 1. Part Number Temperature Range Package Packing Marking. 4558C MC4558CPT TSSOP8 Tape & Reel MC4558IN
Wide Bandwidth Dual Bipolar Operational Amplifier Internally compensated Short-circuit protection Gain and phase match between amplifier Low power consumption Pin-to-pin compatible with MC1458/LM358 Gain
2N2219A 2N2222A HIGH SPEED SWITCHES
2N2219A 2N2222A HIGH SPEED SWITCHES PRELIMINARY DATA DESCRIPTION The 2N2219A and 2N2222A are silicon Planar Epitaxial NPN transistors in Jedec TO-39 (for 2N2219A) and in Jedec TO-18 (for 2N2222A) metal
Obsolete Product(s) - Obsolete Product(s)
QUAD 2 INPUT NAND GATE PROPAGATION DELAY TIME t PD = 60ns (Typ.) at V DD = 10V BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V
STD16NF06. N-Channel 60V Ω - 16A - DPAK STripFET II Power MOSFET. General features. Description. Internal schematic diagram.
N-Channel 60V - 0.060Ω - 16A - DPAK STripFET II Power MOSFET General features Type V DSS R DS(on) I D STD16NF06 60V
L4940 SERIES VERY LOW DROP 1.5A REGULATORS
L4940 SERIES VERY LOW DROP 1.5A REGULATORS PRECISE 5, 8.5, 10, 12V OUTPUTS LOW DROPOUT VOLTAGE (500mV Typ. at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
74LVQ14 LOW VOLTAGE CMOS HEX SCHMITT INVERTER
LOW VOLTAGE CMOS HEX SCHMITT INVERTER HIGH SPEED: t PD = 6 ns (TYP.) at V CC = 3.3 V HYSTERESIS INPUT VOLTAGE: V H = 650mV (TYP.) at V CC = 3.0 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: I CC
L272 DUAL POWER OPERATIONAL AMPLIFIERS
L272 DUAL POWER OPERATIONAL AMPLIFIERS OUTPUT CURRENT TO 1 A OPERATES AT LOW VOLTAGES SINGLE OR SPLIT SUPPLY LARGE COMMON-MODE AND DIFFEREN- TIAL MODE RANGE. GROUND COMPATIBLE INPUTS LOW SATURATION VOLTAGE
Obsolete Product(s) - Obsolete Product(s)
HEX INVERTER (SINGLE STATE) HIGH SPEED: t PD = 5ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 10% V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
74V1G77CTR SINGLE D-TYPE LATCH
SINGLE D-TYPE LATCH HIGH SPEED: t PD = 4.4ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL
Obsolete Product(s) - Obsolete Product(s)
HEX BUFFER/CONVERTER (INVERTING) PROPAGATION DELAY TIME t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT CAPABILITY
STD10NF10 N-CHANNEL 100V Ω - 13A IPAK/DPAK LOW GATE CHARGE STripFET II POWER MOSFET
N-CHANNEL 100V - 0.115 Ω - 13A IPAK/DPAK LOW GATE CHARGE STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STD10NF10 100 V
STD20NF06L N-CHANNEL 60V Ω - 24A DPAK/IPAK STripFET II POWER MOSFET
Table 1: General Features N-CHANNEL 60V - 0.032 Ω - 24A DPAK/IPAK STripFET II POWER MOSFET Figure 1:Package TYPE V DSS R DS(on) I D -1 60 V 60 V TYPICAL R DS (on) = 0.032 Ω < 0.040 Ω < 0.040 Ω EXCEPTIONAL
L9333 QUAD LOW SIDE DRIVER
QUAD LOW SIDE DRIVER WIDE OPERATING SUPPLY VOLTAGE RANGE FROM 4.5V UP TO 32V FOR TRANSIENT 45V VERY LOW STANDBY QUIESCENT CURRENT TYPICALLY < 2µA INPUT TO OUTPUT SIGNAL TRANSFER FUNCTION PROGRAMMABLE HIGH
HCF4020B RIPPLE-CARRY BINARY COUNTER/DIVIDERS 14 STAGE
RIPPLE-CARRY BINARY COUNTER/DIVIDERS 14 STAGE MEDIUM SPEED OPERATION: 16MHz (Typ.) at V DD = 10V FULLY STATIC OPERATION COMMON RESET BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS
QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS
QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS 15V DIGITAL OR ± 7.5V PEAK TO PEAK SWITCHING 125Ω TYPICAL ON RESISTANCE FOR 15V OPERATION SWITCH ON RESISTANCE MATCHED
Obsolete Product(s) - Obsolete Product(s)
N-CHANNEL 30V - 0.016 Ω - 9A SO-8 LOW GATE CHARGE STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STS9NF3LL 30 V
TDA7376PD. 2 x 35 W power amplifier for car radio. Features. Description
2 x 35 W power amplifier for car radio Features High output power capability: 2 x 40 W max./4 2 x 35 W/4 EIAJ 2 x 25 W/4 @14.4 V, 1 khz, 10 % 2 x 25 W/2 @14.4 V, 1 khz, 10 % 2 driving Differential inputs
Obsolete Product(s) - Obsolete Product(s)
2 W mono amplifier Features 2 W output power into 8 Ω at 12 V, THD = 10% Internally fixed gain of 32 db No feedback capacitor No boucherot cell Thermal protection AC short-circuit protection SVR capacitor
LOW VOLTAGE ANALOG AUDIO PROCESSOR WITH HEADPHONE POWER AMPLIFIER MUX_R TREBLE-L. gm RB. +6dB 0dB VOLUME TREBLE OUT-R 25K.
LOW VOLTAGE ANALOG AUDIO PROCESSOR WITH HEADPHONE POWER AMPLIFIER 1 FEATURES 2 STEREO INPUT 1 STEREO OUTPUT TREBLE BOOST BASS CONTROL BASS AUTOMATIC LEVEL CONTROL VOLUME CONTROL IN 1dB STEPS MUTE STAND-BY
-55 to 175 C T j ( ) Pulse width limited by safe operating area.
N-CHANNEL 60V - 0.020 Ω - 28A IPAK/DPAK STripFET II POWER MOSFET TYPE V DSS R DS(on) I D 60 V
L4941 VERY LOW DROP 1A REGULATOR
VERY LOW DROP 1A REGULATOR LOW DROPOUT VOLTAGE (450mV Typ. at 1A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY PROTECTION DESCRIPTION The L4941 is a three terminal