RF Characterization Report
|
|
|
- Norah Williams
- 5 years ago
- Views:
Transcription
1 RF178 Series Cable Assemblies RF178-2SJ1-2SJ1-35 RF178-2RP1-2RP1-35 RF178-2SP1-2SP1-36 RF178-3RP1-3RP1-36 RF178-S7RP4-S7RP4-35 RF178-S7SP4-S7SP4-35 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Samtec Inc. Phone: Park East Blvd. 1-8-SAMTEC-9 (US & Canada) Fax: New Albany IN USA RF@samtec.com Report Revision: 12/6/211 Samtec, Inc. 25 All Rights Reserved
2 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Table of Contents Test Setup Information... 1 Scope:... 1 Product Description:... 1 Test Calibration:... 1 Adapter Use:... 2 Definition of Assembly under Test:... 2 Port Designations:... 2 Legend for Plots:... 2 Results Summary... 3 RF178-2SJ1-2SJ RF178-2RP1-2RP RF178-2SP1-2SP RF178-3RP1-3RP RF178-S7RP4-S7RP RF178-S7SP4-S7SP Instrument Setup:... 9 Test Fixtures:... 1 Samtec Inc. Phone: Park East Blvd. 1-8-SAMTEC-9 (US & Canada) Fax: New Albany IN USA RF@samtec.com Report Revision: 12/6/211 Samtec, Inc. 25 Page:ii All Rights Reserved
3 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Test Setup Information Scope: To perform characterization tests, Insertion Loss, Return Loss and Voltage Standing Wave Ratio. Product Description: The table below presents a description of the different RF178 series cable assemblies that were tested. Part Number Length Termination End 1 Termination End 2 RF178-2SJ1-2SJ mm MCX, Straight, Jack MCX, Straight, Jack RF178-2RP1-2RP mm MCX, Right Angle, Plug MCX, Right Angle, Plug RF178-2SP1-2SP mm MCX, Straight, Plug MCX, Straight, Plug RF178-3RP1-3RP mm MMCX, Right Angle, Plug MMCX, Right Angle, Plug RF178-S7RP4-S7RP mm SSMB, Right Angle, Plug SSMB, Right Angle, Plug RF178-S7SP4-S7SP mm SSMB, Straight, Plug SSMB, Straight, Plug Test Calibration: Calibration is performed using Agilent electronic calibration module, PN or Agilent mechanical calibration kit, PN 8552D to the calibration point below. Any adapters beyond this point are included in the measurements. (Sample setup of adapters, actual setup not depicted.) RF@samtec.com Report Revision: 12/6/211 Page:1
4 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Adapter Use: Each port uses at least one precision adapter capable of mating to the assembly under test. Any supplementary adapter will contribute additional electrical characteristics to the measured data. Any use of additional adapters is noted. Product Part Number Used Adapter Part Number Adapter End 1 Adapter End 2 Vender Used Quantity RF178-2SJ1-2SJ1-35 PE9463 N Jack MCX Plug Pasternack 2 RF178-2RP1-2RP1-35 PE9462 N Jack MCX Jack Pasternack 2 RF178-2SP1-2SP1-36 PE9462 N Jack MCX Jack Pasternack 2 RF178-3RP1-3RP1-36 PE9478 SMA Plug MMCX Jack Pasternack 2 RF178-S7RP4-S7RP4-35 PE941 SMA Plug SSMB Jack Pasternack 2 RF178-S7SP4-S7SP4-35 PE941 SMA Plug SSMB Jack Pasternack 2 Definition of Assembly under Test: The performance characteristics include the interface with adapters. Port Designations: The connector attached to port 1 of the VNA is End 1 from the part number callout. Insertion Loss is measured using S21 and Return Loss / VSWR is measured using S11. Legend for Plots: 5 samples were tested. Only the min/max plots are shown for clarity in this report. RF@samtec.com Report Revision: 12/6/211 Page:2
5 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Results Summary RF178-2SJ1-2SJ1-35 Insertion Loss -.5 IL(dB) RL(dB) -2.5 Return Loss Voltage Standing Wave Ratio VSWR RF@samtec.com Report Revision: 12/6/211 Page:3
6 Description: RF Cable Assembly, 5 Ohm, RG178 Cable RF178-2RP1-2RP1-35 Insertion Loss -.5 IL(dB) Return Loss RL(dB) Voltage Standing Wave Ratio 1.8 VSWR RF@samtec.com Report Revision: 12/6/211 Page:4
7 Description: RF Cable Assembly, 5 Ohm, RG178 Cable RF178-2SP1-2SP1-36 Insertion Loss IL(dB) Return Loss -1-2 RL(dB) -3-4 VSWR Voltage Standing Wave Ratio RF@samtec.com Report Revision: 12/6/211 Page:5
8 Description: RF Cable Assembly, 5 Ohm, RG178 Cable RF178-3RP1-3RP1-36 Insertion Loss IL(dB) Return Loss -1-2 RL(dB) -3-4 VSWR Voltage Standing Wave Ratio RF@samtec.com Report Revision: 12/6/211 Page:6
9 Description: RF Cable Assembly, 5 Ohm, RG178 Cable RF178-S7RP4-S7RP4-35 Insertion Loss -.5 IL(dB) Return Loss RL(dB) Voltage Standing Wave Ratio 1.8 VSWR RF@samtec.com Report Revision: 12/6/211 Page:7
10 Description: RF Cable Assembly, 5 Ohm, RG178 Cable RF178-S7SP4-S7SP4-35 Insertion Loss -.5 IL(dB) RL(dB) -2.5 Return Loss Voltage Standing Wave Ratio VSWR RF@samtec.com Report Revision: 12/6/211 Page:8
11 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Instrument Setup: For some of test results, network analyzer (Agilent E571C) was used and setup as below: Network Analyzer Agilent E571C ENA Series (9 KHz GHz Range) Mechanical Calibration Kit 8532F Electronic Calibration Kit Averaging Factor 4 Smoothing Off IF Bandwidth 3 Hz Sweep Start 5 MHz Sweep End 8.5 GHz Points 61 For some of test results, network analyzer (Agilent N523C) was used and setup as below: Network Analyzer Mechanical Calibration Kit Electronic Calibration Kit Agilent N523C PNA-L Series (3 KHz - 2 GHz) 8552D N4433A Averaging Factor Smoothing Off IF Bandwidth 1 KHz Sweep Start 3 KHz Sweep End 2 GHz Points 161 RF@samtec.com Report Revision: 12/6/211 Page:9
12 Description: RF Cable Assembly, 5 Ohm, RG178 Cable Test Fixtures: E571C (Typical set-up, actual part not depicted.) N523C (Typical set-up, actual part not depicted.) RF@samtec.com Report Revision: 12/6/211 Page:1
RF Characterization Report
RF36 Series Cable Assemblies RF36-SJ-SJ-3 RF36-RP-RP-36 RF36-SP-SP-36 RF36-3SP-3SP-36 RF36-3RP-3RP-36 RF36-5SP-5SP-35 RF36-5BJ-5BJ-3 RF36-6BJ-6BJ-35 RF36-7SP-7SP-33 RF36-7RP-7RP-37 RF36-7BJ-7BJ-36 RF36-S7RP4-S7RP4-35
RF Characterization Report
SMA-J-P-H-ST-MT1 Mated with: RF316-01SP1-01BJ1-0305 Description: 50-Ω SMA Board Mount Jack, Mixed Technology Samtec, Inc. 2005 All Rights Reserved Table of Contents Introduction...1 Product Description...1
High Speed Competitive Comparison Report. Samtec MMCX-J-P-H-ST-TH1 Mated With MMCX-P-P-H-ST-TH1 Competitor A (Mated Set) Competitor B (Mated Set)
High Speed Competitive Comparison Report Samtec MMCX-J-P-H-ST-TH1 Mated With MMCX-P-P-H-ST-TH1 Competitor A (Mated Set) Competitor B (Mated Set) REVISION DATE: January 6, 2005 TABLE OF CONTENTS Introduction...
High Speed Characterization Report
High Speed Characterization Report MMCX-P-P-H-ST-TH1 mated with MMCX-J-P-H-ST-TH1 MMCX-P-P-H-ST-MT1 mated with MMCX-J-P-H-ST-MT1 MMCX-P-P-H-ST-SM1 mated with MMCX-J-P-H-ST-SM1 MMCX-P-P-H-ST-EM1 mated with
SPICE Model Validation Report
HFEM-SE High Speed Flex Data Link Mated with: QTE-xxx-01-x-D-A QSE-xxx-01-x-D-A Description: Flex Data Link, High Speed, 0.8mm Pitch New Albany IN 47151-1147 USA SIG@samtec.com Report Revision: 9/13/2007
Shielding Effectiveness Comparison Report
Shielding Effectiveness Comparison Report Shielded (RF316) and Double-Shielded (RS316) Series Cable Assemblies Mates with MCX, MMCX, MMCXV, SMA, SMB5, SSMB, BNC, TNC Description: 50Ω RG316 RF Cable WWW.SAMTEC.COM
Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification
Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification J. Ferry, C. Arroyo Copyright 2008 Samtec, Inc Page 1 Summary LIFEJACK met or exceeded TIA/EIA-568-B.2-2001 Category 5e requirements for Insertion
EXPERIMENT EM3 INTRODUCTION TO THE NETWORK ANALYZER
ECE 351 ELECTROMAGNETICS EXPERIMENT EM3 INTRODUCTION TO THE NETWORK ANALYZER OBJECTIVE: The objective to this experiment is to introduce the student to some of the capabilities of a vector network analyzer.
High Speed Characterization Report
QTH-030-01-L-D-A Mates with QSH-030-01-L-D-A Description: High Speed Ground Plane Header Board-to-Board, 0.5mm (.0197 ) Pitch, 5mm (.1969 ) Stack Height Samtec, Inc. 2005 All Rights Reserved Table of Contents
CABLE ORDERING INFORMATION How to Build Custom Cable Assemblies
p.1 CABLE ORDERING INFORMATION How to Build Custom Cable Assemblies Using our Cable Specification Chart and Connector Designation Code Chart, you can easily develop your own part numbers for custom cable
High Speed Characterization Report
SSW-1XX-22-X-D-VS Mates with TSM-1XX-1-X-DV-X Description: Surface Mount Terminal Strip,.1 [2.54mm] Pitch, 13.59mm (.535 ) Stack Height Samtec, Inc. 25 All Rights Reserved Table of Contents Connector Overview...
Validation Report Comparison of Eye Patterns Generated By Synopsys HSPICE and the Agilent PLTS
Comparison of Eye Patterns Generated By Synopsys HSPICE and the Agilent PLTS Using: Final Inch Test/Eval Kit, Differential Pair - No Grounds Configuration, QTE-DP/QSE-DP, 5mm Stack Height (P/N FIK-QxE-04-01)
Electronic Calibration (ECal) Modules for Vector Network Analyzers
TECHNICAL OVERVIEW Electronic Calibration (ECal) Modules for Vector Network Analyzers N755xA Series, 2-port Economy ECal Module 8509xC Series, 2-port RF ECal Module N469xD Series, 2-port Microwave ECal
Keysight MOI for USB Type-C Connectors & Cable Assemblies Compliance Tests (Type-C to Legacy Cable Assemblies)
Revision 01.01 Jan-21, 2016 Universal Serial Bus Type-C TM Specification Revision 1.1 Keysight Method of Implementation (MOI) for USB Type-C TM Connectors and Cables Assemblies Compliance Tests Using Keysight
TEST EQUIPMENT PLUS. Signal Hound USB-SA44B / USB-TG44A. Application Note 1: The Smith Chart. Rev. 0
Rev. 0 TEST EQUIPMENT PLUS Signal Hound USB-SA44B / USB-TG44A Application Note 1: The Smith Chart USING THE SMITH CHART Chapter 1 1 Using the Smith Chart Making Single-Frequency Vector Impedance Measurements
EXTEND YOUR REACH. Copper Mountain Technologies USB VNAs. S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11
Copper Mountain Technologies USB VNAs S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11 to S 44 Dynamic range as high as 162 db typ. (1 Hz IF bandwidth) Measurement
Characterizing Non-Standard Impedance Channels with 50 Ohm Instruments
Characterizing Non-Standard Impedance Channels with 50 Ohm Instruments Julian Ferry, Jim Nadolny, Craig Rapp: Samtec Inc. Mike Resso, O.J. Danzy: Agilent Technologies Introduction Emerging systems are
Keysight MOI for USB Type-C Connectors & Cable Assemblies Compliance Tests (Type-C to Legacy Cable Assemblies)
Revision 01.00 Nov-24, 2015 Universal Serial Bus Type-C TM Specification Revision 1.1 Keysight Method of Implementation (MOI) for USB Type-C TM Connectors and Cables Assemblies Compliance Tests Using Keysight
4GHz / 6GHz Radiation Measurement System
4GHz / 6GHz Radiation Measurement System The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces. With a frequency
High Speed Characterization Report
PCRF-064-XXXX-EC-SMA-P-1 Mated with: PCIE-XXX-02-X-D-TH Description: PCI Express Cable Assembly, Low Loss Microwave Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly Overview...
242, , FAX.
TEL. 886 2 8994 1601, FAX. 886 2 8994 1602 sales@rfconnector.com.tw, www.rfconnector.com.tw General Information SMA SMB Subminiature Connectors Screw Lock Subminiature Connectors Snap Lock 50 Ω 18 GHz
Keysight E5061B ENA Vector Network Analyzer CONFIGURATION GUIDE
Keysight E5061B ENA Vector Network Analyzer CONFIGURATION GUIDE Ordering guide The following steps will guide you through configuring your E5061B. Standard furnished item 1 Installation guide CD ROM IO
Picture. Parameter Unit Minimum Typical Maximum. Fin and Ref Input Frequency Range MHz Input Power Level dbm
eatures requency Range: 3 to 300MHz Input Power: -10 to +17dBm Integrated Loop ilter Directly Interface to PS Series Directly Interface to VCO Series DC Power: 12V SMA Connector Picture is a Phase/requency
Radio ETI031 Laboratory Experiments 2: VECTOR NETWORK ANALYSER, ANTENNA and RECEIVER MEASUREMENTS
Lund University Electrical and Information Technology GJ 2007-09-30 Radio ETI031 Laboratory Experiments 2: VECTOR NETWORK ANALYSER, ANTENNA and RECEIVER MEASUREMENTS Göran Jönsson 2007 Objectives: Part
Electrical Performance Report 85 ohm Reference Impedance
ERM8-050-09.0-S-DV Mates with ERF8-050-07.0-S-DV Description: Edge Rate Strip Series, 0.8mm Centerline 16mm Stack Height Samtec, Inc. 2005 All Rights Reserved TABLE OF CONTENTS Connector Overview... 1
High Speed Characterization Report
PCIEC-XXX-XXXX-EC-EM-P Mated with: PCIE-XXX-02-X-D-TH Description: 1.00 mm PCI Express Internal Cable Assembly, 30 AWG Twinax Ribbon Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable
Picture. Parameter Unit Minimum Typical Maximum. Fin and Ref Input Frequency Range MHz 5 25 Input Power Level dbm
eatures requency Range: 5 to 25MHz Input Power: -3 to +17dBm Integrated Loop ilter Directly Interface to PS Series Directly Interface to VCO Series DC Power: 12V SMA Connector Picture is a Phase/requency
Agilent AN Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note
Agilent AN 346-2 Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note Introduction How a balanced circuit differs from an unbalanced circuit A balanced circuit
SECTION 5 SWITCHING CONNECTORS/MOEBIUS MC-CARD/RP-MCX R199/R299 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 5 SWITCHING CONNECTORS/MOEBIUS MC-CARD/RP-MCX R199/R299 SIMPLIFICATION IS OUR INNOVATON Visit www.radiall.com for more information Contents Introduction... 5-4 to 5-5 MOEBIUS Characteristics...
Agilent N9923A FieldFox RF Vector Network Analyzer 2 MHz to 4/6 GHz. Data Sheet
Agilent N9923A FieldFox RF Vector Network Analyzer 2 MHz to 4/6 GHz Data Sheet Table of Contents Definitions... 2 FieldFox RF Vector Network Analyzer... 3 Cable and Antenna Analyzer (Option 305)... External
Characterization of SPDT RF Switch (Mini-circuits MSP2TA )
Characterization of SPDT RF Switch (Mini-circuits ) Raul Monsalve SESE, Arizona State University August 18, 2014 2 Description The RF switch Mini-circuits was characterized in terms of repeatability and
Agilent Technologies High-Definition Multimedia
Agilent Technologies High-Definition Multimedia Interface (HDMI) Cable Assembly Compliance Test Test Solution Overview Using the Agilent E5071C ENA Option TDR Last Update 013/08/1 (TH) Purpose This slide
RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].
![RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].](/thumbs/90/101629325.jpg "RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].")
RP SMA Male Connector Solder Attachment for PE-SR402AL, PE-SR402FL, PE-SR402FLJ, PE- SR402TN, RG402, Gold Plated Brass Body RF Connectors Technical Data Sheet PE44724 Configuration SMA Male Reverse Polarity
High Speed Characterization Report
ESCA-XX-XX-XX.XX-1-3 Mated with: SEAF8-XX-05.0-X-XX-2-K SEAM8-XX-S02.0-X-XX-2-K Description: 0.80 mm SEARAY High-Speed/High-Density Array Cable Assembly, 34 AWG Samtec, Inc. 2005 All Rights Reserved Table
Configuration of PNA-X, NVNA and X parameters
Configuration of PNA-X, NVNA and X parameters VNA 1. S-Parameter Measurements 2. Harmonic Measurements NVNA 3. X-Parameter Measurements Introducing the PNA-X 50 GHz 43.5 GHz 26.5 GHz 13.5 GHz PNA-X Agilent
Millimeter Signal Measurements: Techniques, Solutions and Best Practices
New Network Analyzer platform Millimeter Signal Measurements: Techniques, Solutions and Best Practices Phase Noise measurements update 1 N522XA PNA Series Network Analyzer Introducing Highest Performance
Features and Technical Specifications
Features and Technical Specifications PRODU C T SUM M AR Y The HL9402 is a signal splitter and combiner that offers industry-best amplitude and phase match over a bandwidth of 500 khz to 20 GHz (-3 db).
Performance evaluation of two RF power limiters based on PIN diodes
Performance evaluation of two RF power limiters based on PIN diodes Marta Bautista Durán, José A. López-Pérez December 2017 IT-CDT 2017-19 Observatorio de Yebes Apdo. 148, E-19080 Guadalajara SPAIN 1 1
High Speed Characterization Report
HLCD-20-XX-TD-BD-2 Mated with: LSHM-120-XX.X-X-DV-A Description: 0.50 mm Razor Beam High Speed Hermaphroditic Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly
High Speed Characterization Report
ECDP-16-XX-L1-L2-2-2 Mated with: HSEC8-125-XX-XX-DV-X-XX Description: High-Speed 85Ω Differential Edge Card Cable Assembly, 30 AWG ACCELERATE TM Twinax Cable Samtec, Inc. 2005 All Rights Reserved Table
High Speed Characterization Report
ERCD_020_XX_TTR_TED_1_D Mated with: ERF8-020-05.0-S-DV-L Description: 0.8mm Edge Rate High Speed Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable Assembly Overview... 1
Micro Coaxial Connector. Ultrasmall Series with mating height 1.00 mm
MCC Micro Coaxial Connector Ultrasmall Series with mating height 1.00 mm IEEE802.11a b g n WiMAX Bluetooth Zigbee MIMO (Multiple input and multiple output) 1 USS RF V Plug Cable Assembly Mating height
Keysight Technologies UWB Antenna Measurements with the 20 GHz E5071C ENA Network Analyzer. Application Note
Keysight Technologies UWB Antenna Measurements with the 20 GHz E5071C ENA Network Analyzer Application Note Introduction Ultra-wideband (UWB) is a rapidly growing technology that is used to transmit information
Keysight Technologies Electronic Calibration (ECal) Modules for Vector Network Analyzers
Keysight Technologies Electronic Calibration (ECal) Modules for Vector Network Analyzers N4690 Series, 2-port Microwave ECal 85090 Series, 2-port RF ECal N4430 Series, 4-port ECal N7550 Series, 2-port
Shielding Effectiveness Report HQCD
HQCD Mates with QSH, QTH, QSH-EM Description: 0.50mm Q Strip High Speed Coax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Product Overview... 1 Test Overview... 1 Shielded Room
STANDARD COAXIAL CONNECTORS. Eco 7/16 series
STANDARD COAXIAL CONNECTORS Eco 7/16 series Eco 7/16 INTRODUCTION GENERAL Standard coaxial connectors Screw on coupling Compliant to CECC and IEC standards 50 Ω APPLICATIONS Broadcast RF components (filters,
USB 3.1 Cable-Connector Assembly Compliance Tests. Test Solution Overview Using the Keysight E5071C ENA Option TDR. Last Update 2015/02/06
USB 3.1 Cable-Connector Assembly s Test Solution Overview Using the Keysight E5071C ENA Option TDR Last Update 015/0/06 Purpose This slide will show how to make measurements of USB 3.1 cable & connector
SMA Male Connector Crimp/Solder Attachment for RG58, RG303, RG141, PE-C195, PE-P195, LMR-195, inch
SMA Male Connector Crimp/Solder Attachment for RG58, RG303, RG141, PE-C195, PE-P195, LMR-195, 0195 inch RF Connectors Technical Data Sheet PE4215 Configuration SMA Male Connector MIL-STD-348A 50 Ohms Straight
A New Noise Parameter Measurement Method Results in More than 100x Speed Improvement and Enhanced Measurement Accuracy
MAURY MICROWAVE CORPORATION March 2013 A New Noise Parameter Measurement Method Results in More than 100x Speed Improvement and Enhanced Measurement Accuracy Gary Simpson 1, David Ballo 2, Joel Dunsmore
EMC SHIELDING EFFECTIVENESS TEST REPORT : : :
1.0 1 of 16 EMC SHIELDING EFFECTIVENESS TEST REPORT Test Specification Manufacturer Test Samples : : : MIL-DTL-83528F Specialty Silicone Products 1. SSP502-40 Nickel Graphite in silicone 40 Shore A 2.
GC723A / GC724B Cable and Antenna Analyzer
www.gctm.net GC723A / GC724B Cable and Antenna Analyzer GC723A / GC724B Cable and Antenna Analyzer Introduction A large number of abnormal cell site problems are typically caused by the antenna system,
EMC SHIELDING EFFECTIVENESS TEST REPORT : : :
1.0 1 of 15 EMC SHIELDING EFFECTIVENESS TEST REPORT Test Specification Manufacturer Test Samples : : : MIL-DTL-83528F Specialty Silicone Products, Inc. 1. SSP-2529 DOCUMENT HISTORY REVISION ISSUE DATE
Attenuators, Couplers and Filters
Objectives: Attenuators, Couplers and Filters To become familiar with the functionality of common RF devices. To characterize both the reflection and transmission responses of these devices. NOTE: IN CONTRAST
ReversePolarity Series(SMA,BNC,TNC)
RP ReversePolarity Series(SMA,BNC,TNC) Description Reverse polarity BNC, TNC, N & SMA connectors (RP-BNC, RP-TNC, RP-SMA) are designed for uses in wireless applications where a non-standard interface has
Agilent AN Applying Error Correction to Network Analyzer Measurements
Agilent AN 287-3 Applying Error Correction to Network Analyzer Measurements Application Note 2 3 4 4 5 6 7 8 0 2 2 3 3 4 Table of Contents Introduction Sources and Types of Errors Types of Error Correction
RP SMA Male Right Angle Connector Solder Attachment for PE-SR402AL, PE-SR402FL, RG402
RP SMA Male Right Angle Connector Solder Attachment for PE-SR402AL, PE-SR402FL, RG402 RF Connectors Technical Data Sheet PE4790 Configuration SMA Male Reverse Polarity Connector MIL-STD-348 50 Ohms Right
87415A microwave system amplifier A microwave. system amplifier A microwave system amplifier A microwave.
20 Amplifiers 83020A microwave 875A microwave 8308A microwave 8307A microwave 83006A microwave 8705C preamplifier 8705B preamplifier 83050/5A microwave The Agilent 83006/07/08/020/050/05A test s offer
Advanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Agilent 2-Port and 4-Port PNA-X Network Analyzer N5249A - 10 MHz to 8.5 GHz N5241A - 10 MHz to 13.5 GHz N5242A - 10
Data sheets CDN-M, CDN-AF, CDN-S, CDN-T, CDN-RJ, CDN-USB
Data sheets CDN-M, CDN-AF, CDN-S, CDN-T, CDN-J, CDN-USB Coupling and decoupling devices (CDN) for immunity tests 180906 CDN M1, M2, M3, M4, M5, M2/3 PE N C1 C2 Simplified diagram of M3 network CDN M-Types
EMC SHIELDING EFFECTIVENESS TEST REPORT : : :
1.0 1 of 17 EMC SHIELDING EFFECTIVENESS TEST REPORT Test Specification Manufacturer Test Samples : : : MIL-DTL-83528F Specialty Silicone Products 1. SSP547-65 Silver Copper in silicone 65 shore A 2. SSP548-65
Shielding Effectiveness Report HQDP
HQDP Mates with QSH-DP, QTH-DP Description: 0.50mm 100Ω Differential 30 AWG Twinax Cable Assembly Samtec, Inc. 2005 All Rights Reserved Table of Contents Product Overview... 1 Test Overview... 1 Shielded
Agilent 4-Port PNA-L Network Analyzers
Agilent 4-Port PNA-L Network Analyzers N5230A Options 240, 245 300 khz to 20 GHz Speed and accuracy you can count on Integrated 4-port, balanced measurements up to 20 GHz Introducing the 4-port PNA-L network
Picture. Electrical +25 C, 50 Ω System, DC Supply = +12V. Parameter Unit Minimum Typical Maximum
eatures requency Range: 200 to 800MHz Input Power: -7 to +1 Integrated Loop ilter Directly Interface to PS Series Directly Interface to VCO Series DC Power: 12V SMA Connector Picture is a Phase/requency
FieldFox Handheld Education Series Part 3: Calibration Techniques for Precise Field Measurements
FieldFox Handheld Education Series Part 3: Calibration Techniques for Precise Field Measurements FieldFox Handheld Education Series Interference Testing Cable and Antenna Measurements Calibration Techniques
Xeta4. Occupied Bandwidth. Measurements
Xeta4 Occupied Bandwidth Measurements 10/7/2013 Witnessed by Test conducted by Date 10/8/2013 Date 10/8/2013 Page 1 of 39 Introduction... 4 Scope... 4 Equipment Under Test (EUT)... 4 Power Input... 4 Peripheral
Supplementary Information
Supplementary Information Standards Laboratory Calibration Order 1-999999999-1 Model 8481A Manufacturer Agilent Technologies Description Power Sensor, 10 MHz to 18 GHz, -30 to +20 dbm Serial 2 Options
5 ESSENTIAL HINTS TO IMPROVE Millimeter-wave Network Analysis
5 ESSENTIAL HINTS TO IMPROVE Millimeter-wave Network Analysis Contents 5 Essential Hints to Improve Millimeter-wave Network Analysis Ensure Accurate, Repeatable Results Go to Hint 1 > Calibrate for Better
APPLICATION SPECIFICATION
2.4/5GHZ ALANCE ANTENNA(34.9MM*9MM) 1.0 SCOPE This specification describes the antenna application and surrounding. The information in this document is for reference and benchmark purposes only. The user
UFL and Balanced Connectivity & Calibration Kit Overview
UFL and Balanced Connectivity & Calibration Kit Overview MegiQ BV Weegschaalstraat 3 5632 CW Eindhoven The Netherlands +31 40 291 1479 sales@megiq.com Visit our website at www.megiq.com The choice of a
ID SERIES OUTDOOR INDUSTRIAL DIPOLE ANTENNA
ID SERIES OUTDOOR INDUSTRIAL DIPOLE ANTENNA Phone: (8) 736-6677 / Int: +1 541-471-6256 Email: info@linxtechnologies.com / Address: 159 Ort Lane, Merlin, OR 97532 ID SERIES OUTDOOR INDUSTRIAL DIPOLE ANTENNA
Agilent AN Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note
Agilent AN 346-2 Balanced Circuit Measurement with an Impedance Analyzer/LCR Meter/Network Analyzer Application Note Introduction How a balanced circuit differs from an unbalanced circuit A balanced circuit
Microwave Circuit Design and Measurements Lab. INTRODUCTION TO MICROWAVE MEASUREMENTS: DETECTION OF RF POWER AND STANDING WAVES Lab #2
EE 458/558 Microwave Circuit Design and Measurements Lab INTRODUCTION TO MICROWAVE MEASUREMENTS: DETECTION OF RF POWER AND STANDING WAVES Lab #2 The purpose of this lab is to gain a basic understanding
EE290C - Spring 2004 Advanced Topics in Circuit Design
EE290C - Spring 2004 Advanced Topics in Circuit Design Lecture #3 Measurements with VNA and TDR Ben Chia Tu-Th 4 5:30pm 531 Cory Agenda Relationships between time domain and frequency domain TDR Time Domain
QN Male Connector Crimp/Solder Attachment for RG55, RG141, RG142, RG223, RG400
QN Male Connector Crimp/Solder Attachment for RG55, RG141, RG142, RG223, RG400 RF Connectors Technical Data Sheet PE44978 Configuration QN Male Connector 50 Ohms Straight Body Geometry Features Max Operating
WiFi Interface Identifier
WiFi Interface Identifier WiFi Interface Identifier Today s wireless market has exposed us to many new, and some familiar connectors. The wide range of antennas, access points, routers, WLAN s, cellular
AV3672 Series Vector Network Analyzer
AV3672 Series Vector Network Analyzer AV3672A/B/C/D/E (10MHz 13.5 GHz/26.5 GHz/43.5 GHz/50 GHz/67 GHz) Product Overview: AV3672 series vector network analyzer include AV3672A (10MHz 13.5GHz), AV3672B (10MHz
Vector Network Analyzers (VERY) Basics. Tom Powers USPAS SRF Testing Course 19 Jan. 2014
Vector Network Analyzers (VERY) Basics Tom Powers USPAS SRF Testing Course 19 Jan. 2014 S-Parameters A scattering matrix relates the voltage waves incident on the ports of a network to those reflected
High Data Rate Characterization Report
High Data Rate Characterization Report EQRF-020-1000-T-L-SMA-P-1 Mated with: QSE-xxx-01-x-D-A and SMA-J-P-x-ST-TH1 Description: Cable Assembly, High Speed Coax, 0.8 mm Pitch Samtec, Inc. 2005 All Rights
FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR. 2.4GHz LE MODULE MODEL NUMBER: RN4020
FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR 2.4GHz LE MODULE MODEL NUMBER: RN4020 REPORT NUMBER: 14U17191-1 ISSUE DATE: MARCH 21, 2014
TT7000R4. DS Instruments. D text. RF Power Meter, Signal Generator, Frequency Counter. -Key Features-
-Key Features- DS Instruments Power Meter 50 to 7000MHz Frequency Counter 100 to 7000MHz R4 RF Power Meter, Signal Generator, Frequency Counter Signal Generator 300 to 9600MHz Internal 31dB Step Attenuator
Department of Electrical and Computer Engineering ECE332. Lab 3: High Frequency Measurements
Department of Electrical and Computer Engineering ECE332 Version: 1.3.1 Revised: April 30, 2011 Contents 1 Pre-Lab Assignment 2 2 Introduction 2 2.1 Vector Network Analyzer.............................
How the Braid Impedance of Instrumentation Cables Impact PI and SI Measurements
How the Braid Impedance of Instrumentation Cables Impact PI and SI Measurements Istvan Novak (*), Jim Nadolny (*), Gary Biddle (*), Ethan Koether (**), Brandon Wong (*) (*) Samtec, (**) Oracle This session
Physical Test Setup for Impulse Noise Testing
Physical Test Setup for Impulse Noise Testing Larry Cohen Overview Purpose: Use measurement results for the EM coupling (Campbell) clamp to determine a stable physical test setup for impulse noise testing.
High Frequency. ECT-CPG com shop ECT-CPG com
High Frequency HiGH FreQuenCY High Frequency or Radio Frequency (RF) coaxial probes are used for testing high speed circuits in a variety of industries including automotive, wireless communications, satellite,
Specification for Conducted Emission Test
1 of 10 1. EMI Receiver Frequency range 9kHz 7.0 GHz Measurement time per frequency 10 µs to 100 s time sweep, span = 0 Hz - 1 µs to 16000 s Sweep time in steps of 5 % frequency sweep, span 10 Hz - 2.5
TECHNICAL SPECIFICATION FOR RF (TEST &MEASUREMENT) DEVICE
TECHNICAL SPECIFICATION FOR RF (TEST &MEASUREMENT) DEVICE Test and measuring device supports the following measurement functions: A- Cable and Antenna Analyzer, 2 MHz to 4 GHz. B- Spectrum Analyzer, 100
Platform Migration 8510 to PNA. Graham Payne Application Engineer Agilent Technologies
Platform Migration 8510 to PNA Graham Payne Application Engineer Agilent Technologies We set the standard... 8410 8510 When we introduced the 8510, we changed the way S-parameter measurements were made!
High Speed Cable Assemblies
High Speed Cable Assemblies Data Rate Cable Assemblies s.................................. 4-9 Data Rate Coax & Twinax Cable Assemblies DataRay High Density Cable Assemblies Custom Data Rate Cable Capabilities
MWA REVB LNA Measurements
1 MWA REVB LNA Measurements Hamdi Mani, Judd Bowman Abstract The MWA LNA (REVB) was measured on the Low Frequency Radio astronomy Lab using state of the art test equipment. S-parameters of the amplifier
ANTDOM XX CT WPM GPS ANTENNA Functional Specification
ANTDOM XX CT WPM GPS ANTENNA Functional Specification Inventek Systems, LLC 239 Littleton Road, Suite 4D Westford, Massachusetts 01886 978 392 2202 Inventek Systems, LLC ANTDOM Functional Specification
PORTABLE WIDEBAND RF SIGNAL GENERATOR
DS Instruments -Key Features- 25 to 6000MHz Coverage Calibrated RF Power Output SG6000L R11 PORTABLE WIDEBAND RF SIGNAL GENERATOR 31 RF Output Step Attenuator 20 Vernier Range USB COM Interface Industry
Option 010 adds the impedance measurement function to the 4396B. By installing this option
Product Overview Option 010 adds the impedance measurement function to the 4396B. By installing this option into the 4396B spectrum/network/impedance analyzer, you can measure impedance parameters directly.
Shielding Effectiveness Report
VRDPC-050-01-S-D-RA Mates with VPDP/VPLSP/VPSTP Description: Data Rate I/O Cable Assemblies Samtec, Inc. 2005 All Rights Reserved Table of Contents Product Overview... 1 Shielded Room Noise Floor Verification...
High Speed Characterization Report
LSHM-150-06.0-L-DV-A Mates with LSHM-150-06.0-L-DV-A Description: High Speed Hermaphroditic Strip Vertical Surface Mount, 0.5mm (.0197") Centerline, 12.0mm Board-to-Board Stack Height Samtec, Inc. 2005
7/16 DIN Male Connector Clamp/Solder Attachment for RG213, RG55, RG141, RG142, RG223, RG400, RG303, PE-C195, PE-P195, LMR-195
7/16 DIN Male Connector Clamp/Solder Attachment for RG213, RG55, RG141, RG142, RG223, RG400, RG303, PE-C195, PE-P195, LMR-195 RF Connectors Technical Data Sheet PE4567 Configuration 7/16 DIN Male Connector
SMB Connectors. Adaptors-50Ω. Plug to Plug. Jack to Jack. Plug to Jack. Bulkhead Jack to Jack
SMB Connectors Adaptors-50Ω Plug to Plug 1P-801-00 Jack to Jack 1P-802-00 Plug to Jack 1P-803-00 Bulkhead Jack to Jack 1P-804-18 Mini-SMB 75Ω Straight Plug 1P75-111-00 Cable group RG316 Straight PCB Jack
Challenges and Solutions for Removing Fixture Effects in Multi-port Measurements
DesignCon 2008 Challenges and Solutions for Removing Fixture Effects in Multi-port Measurements Robert Schaefer, Agilent Technologies schaefer-public@agilent.com Abstract As data rates continue to rise
SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188 Gold Plated
SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188 Gold Plated RF Connectors Technical Data Sheet PE45145 Configuration SMA Male Connector 50 Ohms Straight Body Geometry RG174, RG316, RG188
Description RF Explorer RFEAH-25 1 is a 25mm diameter, high performance near field H-Loop antenna.
Description RF Explorer RFEAH-25 1 is a 25mm diameter, high performance near field H-Loop antenna. RFEAH-25 is a very sensitive, compact and easy to use H-loop near field antenna. The low-loss design exhibits
RF and Microwave Test and Design Roadshow 5 Locations across Australia and New Zealand
RF and Microwave Test and Design Roadshow 5 Locations across Australia and New Zealand Advanced VNA Measurements Agenda Overview of the PXIe-5632 Architecture SW Experience Overview of VNA Calibration