Bolt-together frame kit guide for Compact Camping Concepts Explorer Box Camping Trailer Revision /01/17
|
|
- Richard Armstrong
- 5 years ago
- Views:
Transcription
1 Bolt-together frame kit guide for Compact Camping Concepts Explorer Box Camping Trailer Revision /01/17 Bolt-together frame kits are a budget friendly option for building an Explorer Box trailer on. There are many sources; Harbor Freight is a readily available and recognized name. This guide is based on Harbor Freight s, Haul-Master # lb. capacity super duty 4 x 8 trailer. #94564 is the previous discontinued part #. The model #62647 has a folding feature which isn t needed for home-built camping trailer projects. The folding hardware doesn t get installed and a couple extra bolts are used for securing the two halves together.
2 A standard Explorer Box is based on a 4 x 6 frame, so a few modifications are necessary. First, the length of the frame deck gets shortened from 96 to 72 long. Second, the position of the spring hangers gets relocated so the axle center line is 27 from the rear of the frame. To make these modifications, you will need a drill, 7/16 drill bit, a couple of clamps and a way to cut steel. For the steel cutting, a hacksaw works, although a 4 1/2" angle grinder with a cutoff wheel goes much faster. Start by reading the frame kit manual and understanding the standard frame building process. This guide follows and references the manual steps. Build the frame: Per the Steps 1-3 instructions, build up the front 4 x4 section. Leave the four #25 stake pockets and two #10 hinge plates off. Steps 4-6 require modifications, the side rails will be shortened and rear 2B cross member will not be used. Side rails 1RL &1RR get shortened to 24. The cut goes through the bolt hole where the center 2B cross member would normally be bolted. The shortened side rails need new 7/16 dia. holes drill for attaching the center 2B cross member which now becomes the rear one. Then assemble the shortened side rails with a front and rear cross member per the instructions, leaving the four #25 stake pockets and #10 L&R hinge plates off.
3 Per Steps 7-11 instructions, attach the tongue section. For Step 12, bolt the front and rear sections together with a couple extra M10 bolts and nuts. Then disregard Step 13.
4 Steps get modified. The front of the spring hanger gets positioned 31 1/4" from the front of the frame. This places the axle centerline 27 from the rear of the frame. This requires drill new holes and bolting the hangers to the front and rear frame sections. Here is the spring hanger holes location information. Three new 7/16 diameter holes need to be drilled in each spring hanger. The new holes are C, D and E. Hole C is positioned over the rear section, front corner cross member hole. Holes D and E are position in approximately the same location as A and B on the front end of the bracket. F is the square hole on top of the spring hanger.
5 With the spring hanger clamped in place, drill the six (per side) new 7/16 diameter hole through the frame. F is drill through the square hole on top of the spring hanger. Now referencing Figure E in Phase 5, bolt the spring hangers in place. For A, B, D, E and F use part #B M10 x 25 bolts. For C use part #C M10 x 30 bolts. Per the Steps instructions, attach the springs and axle, but do not attach the fender seats or fenders. Per the Steps instructions, install the hubs and tires. DO NOT overlook Bearing Packing Instructions. Per the Steps instructions, attach the couple and safety chain. Depending on where your taillights will be installed, you may defer wiring and attaching the lights at this time. Your Basic Frame is now complete! Be sure to read and follow the operating instructions and safety portion of your frame manual.
6 An additional item I put on all trailers is a swivel tongue jack. These make moving your trailer around much easier and allow you to level it.
7 Another additional item if your Explorer Box will be Tent Topped, is a pair of rear leveling / stabilizer jacks. Bolting them to the rear cross member is an easy way to install them. Too better protect them, make brackets and angle them in.
Place the vehicle on a hard level surface and use an appropriate jack and jack stands to raise the vehicle of the ground.
1937-1939 Chevy Truck Rear Air Bag 4 - Link Kit Installation Instructions 1-866-925-1101 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATING OF THE KIT.
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationInstallation Instructions
DODGE RAM 2500 20K Industry Standard SuperRail Custom Mounting Kit #2336 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationk 5356 PINE AVE FRESNO, CA USA TOLL FREE: 877.4X4.TOYS WORLDWIDE:
tacoma front shackle kit 110821-1-k kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950 WWW.TRAIL-GEAR.COM recommended tools Loctite Cutoff Wheel Welder Grinder
More informationInstallation Instructions
TOYOTA 16K Industry Standard Rail Custom Mounting Kit #2748 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationFord Pick Up Rear leaf Spring Kit Installation Instructions
1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4
More informationCHEVY/GMC SuperRail Mounting Kit #3117
CHEVY/GMC SuperRail Mounting Kit #3117 #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 12,000 lbs. 3,000 lbs. Installation Instructions SPECIFICATIONS Fits
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2760 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationCHEVY/GMC SuperRail Mounting Kit #4423
CHEVY/GMC SuperRail Mounting Kit #4423 #4100 SuperGlide (16K) #4400 SuperGlide (20K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationMOR/ryde Steer Axle Suspension System
MOR/ryde Steer Axle Suspension System (Double Eye Leaf Spring) Steer Axle Installation Instructions MOR/ryde International 1966 Moyer Avenue Elkhart, IN 46516 574-293-1581 www.morryde.com SRL153-001 REV.
More informationInstallation Instructions
CHEVY / GMC 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2226 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationMotorcycle Lift Assembly Instructions
Motorcycle Lift Assembly Instructions Copyright JCS 2009 Rev1M Page 1 Lift Table Assembly Instructions The following pages will assist you in the construction of your Motorcycle Lift Table. You will find
More informationRACER TECH rzr lift kit installation instructions
RACER TECH rzr 170 2 lift kit installation instructions Thank You for purchasing this kit. You should have received the following: (2) - Front spindle relocators (2) Front relocator shims (1) - Rear upper
More informationFORD #2228. Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY
FORD 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2228 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in
More informationINSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA MANUAL PART NUMBER:
PARTS-1 Model 24562/28562 Crane INSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 641-923-3711 MANUAL PART NUMBER: 99903701 Iowa Mold Tooling Co., Inc. is an Oshkosh Truck
More informationInstallation Instructions
DODGE 16K Industry Standard Rail Custom Mounting Kit #2728 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationOWNERS MANUAL. Model No UTILITY CART
OWNERS MANUAL Model No. 45-00 UTILITY CART CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts PRINTED IN USA FORM NO. 46274 LOOSE PARTS IN CARTON
More informationPart# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095
Part# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095 Bag Hardware: (8) 5/16 x 1 ½ Allen flat head (14) 3/8 x 1 Hex bolt G5 (2) ½ x 2 ½ Hex Bolt G5 (6) 5/16 flange nuts (14) 3/8 flange nuts (2) ½ stove
More information#2010 #1795. Frame Rack Dyna Mo Clamps Two pair of jaws with 12 draw bar. Grip surface 9-¼ wide. #1929 #1910
Mity Bite Clamp Use for one or two-directional pulling. Good for confined areas. Grip 2 wide. Multi Angle Clamp Pulls from any direction with a 180 arc. Makes two-way pulling faster and easier. Bolt stoppers
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationCHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434
CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434 Installation Instructions SPECIFICATIONS Fits 1999-2010 Chevy 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1067 Hitch
More informationImportant Note. Tools Required: Welder capable of fully welding 10 GA.135 steel
INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11100 (Patent Pending) 1968-72 GM A-Body Coupe/Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires
More informationInstallation Instructions
CHEVY / GMC 16K Industry Standard Rail Custom Mounting Kit #2730 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More information`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line:
`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLING THE KIT.
More informationModel No.'s B
owners manual Model No.'s 45-01012 190-653B UTILITY CARTS (SEE SPECIFICATIONS ON PAGE 7) CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the
More informationINSTRUCTION SHEET. PIECE INVENTORY - MOBILE BASES Refer to the diagram for part identification.
INSTRUCTION SHEET D2260 HEAVY-DUTY MINI-MOBILE BASE D2057 HEAVY-DUTY MOBILE BASE D2058 SUPER HEAVY-DUTY MOBILE BASE D2259 EXTENSION KIT FOR D2260/D2057 D2246 EXTENSION RAIL KIT FOR D2058 This Shop Fox
More informationPARTS MANUAL Rev A
PARTS MANUAL 4000394 Table of Contents Part Index for Trailer --------------------------------------------- 2 Trailer Figure ----------------------------------------------------- 6 Trailer Figure 2 -----------------------------------------------------
More informationTRAILMATE METEOR ASSEMBLY MANUAL
TRAILMATE METEOR ASSEMBLY MANUAL The Trailmate Meteor recumbent has been designed for easy assembly. This means more time to enjoy the smooth ride with single speed, 3 speed coaster brake and 21 speed
More informationMounting the 6 or 12 Indexer on PRS Gantry Tools
Page 1 Mounting the 6 or 12 Indexer on PRS Gantry Tools About this guide: This document illustrates several options for mounting an indexer onto your ShopBot. You can choose the technique that works best
More informationASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND GM FLUSH TAILGATE WITH HANDLE
ASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND 41-53 GM FLUSH TAILGATE WITH HANDLE Build the box assembly according to the MAR-K assembly instructions. When installing the tailgate and latching mechanisms
More informationDetroit Speed, Inc. Heavy Duty Leaf Spring Pocket Kit Camaro/Firebird P/N:
Detroit Speed, Inc. Heavy Duty Leaf Spring Pocket Kit 1967-69 Camaro/Firebird P/N: 040110 Thank you for purchasing the Detroit Speed Inc., Heavy Duty Leaf Spring Pocket Kit for your 1967-69 Camaro/Firebird.
More informationImportant Note. Tools Required: Welder capable of fully welding 10 GA.135 steel
INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11102 (Patent Pending) 1964-67 GM A-Body Coupe/2dr Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires
More informationDO NOT EXCEED LOWER OF TOWING VEHICLE MANUFACTURER'S RATINGS OR THOSE LISTED BELOW:
CATALOG NO. 40050 INSTALLATION INSTRUCTIONS NOTE: CHECK HITCH FREQUENTLY, MAKING SURE ALL FASTENERS AND BALL ARE PROPERLY TIGHTENED. A HITCH OR BALL WHICH HAS BEEN DAMAGED SHOULD BE REMOVED AND REPLACED.
More informationA = 4-1/2 B = 1/4 C = 5/16. Pin Dia. Use with C-11, C-12, C-13, C-19 Use with C-10, C-12, C-13, C dia. A = 4-1/3 A = /16 1-5/8
B C-10 Dia. Pin C-11 Dia. Pin C-12 Dia. Pin Bi-fold Pins & Associated Parts A A = 4- B = C = A = 4-1/6 B = C = A = 4- B = C = C Pin Dia. C-11, C-12, C-13, C-19 C-10, C-12, C-13, C-16 C-13 Dia. Cap C-16
More informationKIT ASSEMBLY INSTRUCTIONS
JUMPING JACK TRAILER KIT KIT ASSEMBLY INSTRUCTIONS A torque wrench (provided in the in-store tool kit) is required to assemble this trailer kit. Torque is a twisting (ft.-lb.).copy force measured in foot-pounds
More informationAgri-Fab. Model No "ATV" DUMP CART H.D. 17 CU. FT. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab owners manual Model No. 45-02172 190-521-100 "ATV" DUMP CART H.D. 17 CU. FT. CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest
More informationS48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM
PAGE 1 OF 6 PORTA-DOCK, INC. S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM Thank you for purchasing our product! *Please read these instructions and follow
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationINSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP
INSTALLATION INSTRUCTIONS Product No. You can take it with you. PLYMOUTH, MICH. MULTI-FIT PICK-UP 37034 SMALL PARTS PACKAGE 37424 WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY OCCUR DUE TO OVER TIGHTENING.
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More informationFactory Assistance: Phone: Fax: Page 1
CABLE RUNWAY ACCESSORIES Radius Drop / Stringer Drop Provides 3 bend radius Radius drop fits 6, 12 and 18 runway made from 1-1/2 x 3/8 tubing Steel construction Includes (3) cable spools, (1) bolt, (1)
More informationAgri-Fab OWNERS MANUAL. Model No WHEEL CART. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-0270 4-WHEEL CART CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest way to purchase parts www.speedepart.com
More informationINSTALLATION INSTRUCTIONS
NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).
More informationBudget Robotics Octabot Assembly Instructions
Budget Robotics Octabot Assembly Instructions The Budget Robotics Octabot kit is a low-cost 7" diameter servo-driven robot base, ready for expansion. Assembly is simple, and takes less than 15 minutes.
More information1. Remove factory stock bump stop and mount from the frame.
1. Disconnect the negative terminal on the battery. With the vehicle on level ground and the emergency brake set, block the front tires. 2. Jack up the rear of the vehicle and support the frame rails with
More informationDetroit Speed, Inc. Heavy Duty Leaf Spring Pocket Kit X-Body P/N:
Detroit Speed, Inc. Heavy Duty Leaf Spring Pocket Kit 1968-74 X-Body P/N: 040111 Thank you for purchasing the Detroit Speed Inc., Heavy Duty Leaf Spring Pocket Kit for your 1968-74 X-Body. The DSE Leaf
More informationREAR FUSELAGE ASSEMBLY
SECTION 5 Tail Attachments on Fuselage Ref Dwg 8RU-3 The rudder hinge line (HL) is parallel to the aft edge of the fuselage skin SECTION 5 - Page 1 of 9 Looking at the top of the rear fuselage. Stabilizer
More informationowners manual CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts
owners manual Model No. 45-0350 (ATV) 45-0351 (FARM) (45-0350 SHOWN) TANDEM AXLE CART CAUTION: Read Rules for Safe Operation and Instructions Carefully IMPORTANT! The wheel bearings are not pre lubricated.
More information6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)
INSTALLATION INSTRUCTIONS FOR THE TAILGATE WITH LATCH AND LINK ASSEMBLY 76-87 FORD SHORT & 53-87 FORD LONG FLARESIDES 1. Assemble the bed and make sure the box is square. Measure the distance between the
More informationEMB MANUFACTURING INC.
TRAILER WOOD PROCESSOR MODELS WP865, WP835, WP635 ASSEMBLY INSTRUCTION MANUAL Please review and understand the operators manual before attempting to operate this machinery. EMB MANUFACTURING INC. 4144
More informationJK Rear Inner Fenders
INSTALLATION INSTRUCTIONS INST-17-05-080_A JK Rear Inner Fenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationFORD 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4431
FORD 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4431 Installation Instructions SPECIFICATIONS Fits 1999 2016 Ford F250 & F350 Short Bed Mounts to B&W gooseneck part #1108 & 1111
More informationCTTR Tire Rack Required tools
CTTR Tire Rack Required tools Torque wrench, ratchet, 9/16 socket, tape measure, and square edge. ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. Failure to follow the assembly instructions
More informationASSEMBLY INSTRUCTIONS FOR T-10, T-11 & T-12 SERIES RACKS
ASSEMBLY INSTRUCTIONS FOR T-10, T-11 & T-12 SERIES RACKS T12SHD-1 with 26 Legs shown above. Package Contents: HARDWARE KIT PARTS (8) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLIES (20) 3/8-16
More informationArcStation. Build your ArcStation. ArcStation. The only workbench designed for welders. MillerWelds.com/ArcStation. MillerWelds.
Build your 30S (5 ) 23 lb (5 kg) 0S (5 ) 230 lb (04 kg) S-series Accessories: 30SX (5 ) 3/-in X-pattern tabletop lb (0 kg) 30FX (300 3) Tabletop style 3/-in X-pattern tabletop 4 lb (34 kg) (35 x 2 x 35
More informationC4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS
C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect
More informationHIGH RISE Portable Restroom Assembly Instructions
HIGH RISE Portable Restroom Assembly Instructions 2530 Xenium Lane North, Minneapolis, MN 55441 Telephone: 763-553-1900 / Fax: 763-553-1905 800-328-3332/ www.satelliteindustries.com PN 20930 REV C 8/16
More informationF594-PLS Platform Beam Scale. Installation/Operation Manual 05.03
F594-PLS Platform Beam Scale Installation/Operation Manual 05.03 16965 Contents 1.0 About This Manual...1 2.0 Installation Instructions...1 2.1 Unpacking.....................................................................
More informationInstallation Instructions: Bumper (Part # SB76850) XJ Jeep Cherokee XRC Rear Bumper
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty 93-7789 XJ XRC 1 93-7807 Bumper Mount Bracket: Drvr 1 93-7811 Bumper Mount Bracket: Pass 1
More informationHaukaas Bale Rack Kit
Page 1 Haukaas Bale Rack Kit For hauling large round bales "Pipe Style". C D Pocket Reinforcement Plates 10" 11" A: Pocket Side Plate B: Pocket Top Plate C: Side Stake D: End Stake E: Floor Plate B A F:
More informationBildaBike Assembly. Cruiser: *Disclaimer*
BildaBike Assembly *Disclaimer* While we do provide basic tools for assembly, we highly recommend visiting your local bike shop to have a professional bike mechanic build or inspect your new bike. There
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More information1 PREPARE HEADER AND ROUGH OPENING
CONTENTS. HEADER & TRACK ASSEMBLY. END BRACKET PLAIN 3. FLOOR PLATE.. 8. 4. SPLIT STUD 6 5. CARRIER (987) 6. QUICK RELEASE PLATE (960) 7. DOOR GUIDE SET (9883) 3. 4. 7. 8. BUMPER KIT (988) 9. #8 X 3/4
More informationCHEVY SuperBracket Mounting Kit #0826
CHEVY SuperBracket Mounting Kit #0826 #1200 SuperGlide (16K) #0800 SuperGlide (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationMANUAL DE MONTAJE ASSEMBLY MANUAL AIREADOR DE PLUG AERATOR MODEL # AE-48T. Hardware & Parts Listing Assembly Instructions Maintenance Notes for
ASSEMBLY MANUAL Hardware & Parts Listing Assembly Instructions Maintenance Notes for 48 PLUG AERATOR MANUAL DE MONTAJE Lista de piezas y tornillería Instrucciones de armado Notas de mantenimiento para
More informationOWNERS MANUAL. Model No UTILITY CART. CAUTION: Read Rules for Safe Operation and Instructions Carefully
OWNERS MANUAL Model No. 45-01003 UTILITY CART CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest way to purchase parts www.speedepart.com
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationFRAME BRACKET. Doing Our Best to Provide You the Best. Ford. Page 1. BOlT TORQUE SPECIFICATIONS HJ31000,Rev 0
2-13 HJ31000,Rev 0 Ford BOlT TORQUE SPECIFICATIONS METRIC BOlTS Size Grade Torque 8mm 8.8 23 ft/lbs. 10mm 8.8 45 ft/lbs. 12mm 8.8 78 ft/lbs. 14mm 8.8 125 ft/lbs. STANDARD BOlTS Size Grade Torque 5/16 5
More informationPhone #: (360) Online Tech Support: Web:
Phone #: (360) 734-3482 Online Tech Support: tech-support@shopfox.biz Web: www.shopfox.biz Your new Model D2058A Super-Heavy Duty Mobile Base () is designed to give you a stable and mobile platform upon
More informationOpen Up Your View With CABLE SYSTEMS
Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching
More informationInstallation Instructions Universal Crossmember Kit - 60 Track Width BEFORE Measure Twice, Weld Once! II
Installation Instructions Universal Crossmember Kit - 60 Track Width Please read these instructions completely BEFORE starting your installation. Remember the basic rule for a successful installation:
More informationCoburn Interior Sliding Systems. Coburn COBURN SLIDING SYSTEMS
Coburn Interior Sliding Systems Coburn COBURN SLIDING SYSTEMS Interior Sliding Door Gears FOR CUPBOARDS, WARDROBES, INTERIOR SLIDING AND FOLDING DOORS A comprehensive range of top hung and bottom rolling
More informationInstallation Instructions
DODGE 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4433 Installation Instructions SPECIFICATIONS Fits 2003 2012 Dodge 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1307 &
More informationSAVVY OFF ROAD GAS TANK SKID INSTALLATION INSTRUCTIONS
It is best to work with a fuel tank that has the least amount of fuel in it as possible. Thank you for purchasing the best skid on the market. Please follow these instructions and your installation should
More informationMounting Brackets for 8450 Drawer Slides KV Front Bracket 20 $1.30 KV P Rear Bracket 20 $5.20
Mounts bottom or side 1/2 clearance plus 1/32 0 lb. load with model Almond finish Integrated soft-close mechanism 32mm hole pattern with direct access mounting Lever disconnect for easy drawer removal
More informationAPPLICATION: Installation No. Installation No.
June 2007 INSTALLATION INSTRUCTIONS MODEL NO. 82650 WARNING: Although this hitch is designed to safely tow its rated load, we recommend that you consult your vehicle owner's manual for possible manufacturer's
More informationSole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training
Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training Delivery Requirements Ground delivery Inside delivery to customer-specified location Unpack and assemble machine, and remove packing
More informationFRAME BRACKET. Doing Our Best to Provide You the Best. Ford F250, F350 & F parts list. Page 1. 2/17 HJ32002,Rev 2.
2/17 HJ32002,Rev 2 BOlt torque specifications MEtRiC BOlts size Grade torque 8mm 8.8 23 ft/lbs. 10mm 8.8 45 ft/lbs. 12mm 8.8 78 ft/lbs. 14mm 8.8 125 ft/lbs. standard BOlts size Grade torque 5/16 5 18 ft/lbs.
More informationTransmission Line Support Systems
Antenna Support Bracket for transmission line The Antenna Support Bracket angle mounts directly to a 4-1/2" (114 mm) OD antenna pipe mount or tower leg. This is ideal for supporting transmission line runs
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationChain Drive Vise. Installation Instructions. (revised 05/04/2016)
Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationPPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com.
More informationCHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4432
CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4432 Installation Instructions SPECIFICATIONS Fits 2011-2018 Chevy 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1011 Hitch
More information11431 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-PRESENT MAKE: FORD MODEL: FOCUS ST STYLE: HATCHBACK WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationRetro Fit Gearbox Mount. Assembly Instructions. Assembly Instructions. Before You Start. General Information. Manual No M
Retro Fit Gearbox Mount Assembly Instructions Treker 4400NT & 4400ST Series Before You Start Assembly Instructions Manual No. 700-372M! When you see this symbol, the subsequent instructions and warnings
More informationsouthpaw enterprises, inc.
southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Wood Joist 2-1/2 Ft. Drop Ceiling
More informationVertical Mute Rail Installation
Vertical Mute Rail Installation Before you start the installation we recommend that you take note of the present state of the piano in which the QuietTime system with be installed into. 1. Check the over
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationCUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS
20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air
More informationInstalling AZEK Evolutions Rail
Installing Evolutions Rail TM Contemporary Installing AZEK Evolutions Rail Installing Evolutions Rail Contemporary Style... 2 Installing CableRail by Feeney for Evolutions Rail Contemporary Style... 8
More informationSolar Panel Top-of-Pole Mounting Kit For Panels Over 100 Watts Including CMP Panels
Solar Panel Top-of-Pole Mounting Kit For Panels Over 100 Watts Including CMP Panels Thank you for purchasing the top-of-pole solar panel mounting kit. This mounting system is designed to enable the solar
More informationGeneral Guidelines:
ASSEMBLY INSTRUCTIONS Congratulations on your new Patriot Dock purchase. This manual contains instructions to assemble basic dock configurations for use at typical residential shoreline application. Please
More informationFORD Ford Aerostar Van (extended only) Ford Bronco Ford Bronco II Ford Ranger P/U (except Flareside)
June 2007 INSTALLATION INSTRUCTIONS Rev. 1 MODEL NO. 82650 APPLICATION: CHEVROLET/GMC 1992-94 Chevrolet Blazer (full size) 1996-04 Chevrolet/GMC Van (full size) 1983-04 Chevrolet S-10 P/U (short bed, EXC
More informationCommander 2 Lift Kit
Commander 2 Lift Kit Can-Am Commander 2010+ Part #: 5102204 Rev. 082416 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING RT Pro UTV
More informationHex Head Bolt Set N - Includes lock nut. Used to connect male and female T connectors. Galvanized. 3/4" x 3-1/2". Standard Grade (f) Part #24279
a Standard Grade (3/16 ) and Commercial Grade(1/4 ) Tie Down Is designed for use with 1-1/2" thick lumber (minimum width 6"). All hardware is mounted with 3/8" carriage bolts. All male and female dock
More information