APPLICATION DATA SHEET

Transcription

1 APPLICATION DATA SHEET ENVIROGRAF AP Product Number: 69 Intumescent Surface Mounted Fire & Smoke Seals Description: This is a surface-mounted intumescent fire or fire and smoke seal available in black, brown, red, white, and real wood veneer finishes. No routing is necessary. Supplied as a pack with intumescent paper for use around lock and hinge areas and two labels printed Fire Door Keep Shut. Fixing requirements: Ensure that a minimum 3mm - 3½mm gap exists between door and frame, down the closing stile and across the head. Only a 1mm gap is required down the back edge as the standard strip is only 1mm thick and covers hinges without binding. Important Note: Existing painted or varnished door frames must be cleaned thoroughly with white spirit or detergent water and completely dry before application of seals. For new woodwork the surface must be sealed with sealant/paint before seal application. Application: Peel off backing paper from the self-adhesive fixing strip starting on the brush side and, with the smoke seal touching the door stop, press the intumescent seal into position. The seal can be easily cut with a sharp knife to fit around lock areas. Two 1100mm lengths are supplied for fitting down the closing stile and these are 2.4mm thick. One 1000mm long x 2.4mm thick strip is supplied for the head of the door frame. Two 1100mm long strips (1mm thick in standard version and 2.3mm thick in plastic version) are supplied for the back of the door frame, and these adhere from top to bottom, over the hinges (this helps to cool the hinges and screws in a fire). Intumescent paper is supplied for application around a rebated lock, to cool the lock in a fire. Remove lock from door, cut Envirograf intumescent paper to size, wrap it around lock and sandwich it between the lock and door as you replace the lock. Also place paper under the keep plate. Labels are supplied for single or double doors, printed Fire Door Keep Shut. These seals comply with BS476 Part 22. The intumescent seals can be painted or varnished over but the brush must not be painted. If the brush is accidentally painted over it can be easily replaced by ordering Envirograf Product 72 brush seals as replacements. Note: panel pins are supplied to secure through the brush smoke seal at each end and every 300mm apart along its length. These panel pins must be fitted as requested by building control officers and fire officers. DISTRIBUTED BY: NORSEAL LTD. UNIT5 REGENTS DRIVE, LOW PRUDHOE INDUSTRIAL ESTATE, PRUDHOE, NE42 6PX TEL: , FREE FAX:

2 TECHNICAL DATA SHEET ENVIROGRAF TD Description: Product Number: 69 Intumescent Surface Mounted Fire & Smoke Seals This is a surface-mounted intumescent fire or fire and smoke seal available in black, brown, red, white, and real wood veneer finishes. No routing is necessary. Supplied as a pack with intumescent paper for use around lock and hinge areas and two labels printed Fire Door Keep Shut. Use: This product is fitted to door frames in minutes. A 3½mm or greater gap down the closing stile and across the door head is al that is required. Seals fit directly over hinges with no hinge bind and no special gap is necessary on hinge side. Once fitted the face of the seal can be painted, although the brush smoke seal must NOT be painted. If the brush is painted in error it is easy to replace. The seals have a self-adhesive backing but pins are also supplied for added security of fitting. Ordering references: REF TYPE COLOUR ES/SDS Single door set Brown, white, red, black ES/SDW Single door set Real wood veneer oak, sapele, ash ES/DDS Double door set Brown, white, red, black ES/DDW Double door set Real wood veneer oak, sapele, ash REF TYPE COLOUR NS/SDS Single door set Brown, white, red, black NS/SDW Single door set Real wood veneer oak, sapele, ash NS/DDS Double door set Brown, white, red, black NS/DDW Double door set Real wood veneer oak, sapele, ash (ES sets are fire and smoke seals but NS sets are fire seals only) State finish required and whether rebated or open stiles on double doors. If the gap at the closing stile and across the head of the door is less than 3mm request packs containing only 1mm thick ES/30/PS seals. Single strips can be supplied. Please see price list for full range and ordering information Test Details: Integrity Insulation Trada IT Minutes N/A Trada RF Minutes N/A DISTRIBUTED BY: NORSEAL LTD. UNIT5 REGENTS DRIVE, LOW PRUDHOE INDUSTRIAL ESTATE, PRUDHOE, NE42 6PX TEL: , FREE FAX:

3 COSHH DATA SHEET ENVIROGRAF HS Product Number: 69 Intumescent Surface Mounted Fire & Smoke Seals This is a surface-mounted intumescent fire or fire and smoke seal available in black, brown, red, white, and real wood veneer finishes. No routing is necessary. This product comprises of the following materials and therefore is supported by Health & Safety Data Sheets: (Appendix 1) Intumescent material *The information contained in this safety data sheet is given in good faith. It is accurate to the best of our knowledge and belief and represents the most up to date information. The information given in this data sheet does not constitute or replace the user s own assessment of workplace risk as required by other health and safety legislation.

4 HSA Issue 1 Appendix 1 MULTIGRAF INTUMESCENT MATERIAL 1. IDENTIFICATION OF THE PREPARATION AND COMPANY PRODUCT NAME: Multigraf Intumescent Material MANUFACTURER/SUPPLIER: Intumescent Systems Ltd ADDRESS: Envirograf House, Barfrestone, Nr. Dover, Kent, CT15 7JG TELEPHONE / FAX / sales@envirograf.com EMERGENCY PHONE NUMBER: COMPOSITION/INFORMATION ON INGREDIENTS CHEMICAL CONSTITUTION Mineral Wool Fibre % by weight Exfoliating Graphite % by weight Organic binder (including adhesive coating) % by weight 3. HAZARDS IDENTIFICATION Cutting through the material and surface scuffing may release small amounts of airborne fibre, clay and carbon dust which are mechanically irritant to skin, eyes and upper respiratory system. Based on animal studies, excessive exposure to man made mineral fibre dust may cause lung damage (fibrosis) and tumours. As with any dust, pre-existing upper respiratory symptoms and lung diseases may be aggravated. 4. FIRST AID MEASURES SKIN: EYES: INGESTION: INHALATION: Rinse affected areas with water and wash gently with soap. Do not use detergent. Flush eyes with large quantities of water, Have eye bath readily available in areas where eye contact may occur. Seek medical attention if irritation continues. Drink plenty of water. Seek medical advice. Remove to fresh air, drink water and clear throat and blow nose to evacuate fibre/dust. Seek medical attention. 5. FIRE FIGHTING MEASURES SUITABLE EXTINGUISHING MEDIA: Use extinguishing agent suitable for type of surrounding combustible materials. Do not inhale products of combustion. 6. ACCIDENTAL RELEASE MEASURES Store product in original wrapping until required for use. Do not allow dust to be windblown. Do not use compressed air to blow dust or fibres. Unwanted product should be collected and stored in sealed bags. Dust/fibre should be removed using a suitable vacuum cleaner with HEPA exhaust air filtration and disposal collection bags; used bags to be sealed before disposal. If sweeping is required the area should be damped down with water before brushing

5 7. HANDLING AND STORAGE HANDLING: STORAGE: Keep dust generation to a minimum. Store dry and cool. Keep in original wrapping until required for use. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION APPLICABLE OCCUPATIONAL EXPOSURE LIMITS: MAN MADE MINERAL FIBRE: *ME 2.0 fibres/ml & 5 mg/m; (8 hr TWA) FINE CARBON DUST: *OES 3.5 mg/m; (8 hr TWA) and 7 mg/m; (STEL) *(UK Health & Safety Executive - OEL EH40/98) RESPIRATORY PROTECTION: HAND PROTECTION: EYE PROTECTION: SKIN PROTECTION: Wear disposable dust respirator (eg. 3M 8810 or equivalent). Use of gloves is recommended. Wear goggles or safety glasses with side shields. Do not wear contact lenses. Wear overalls that are loose fitting at the neck and wrists. 9. PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE: DENSITY: EXPANSION: FLAMMABILITY: Flexible Grey fibrous mat with black speckle kg/m; Rapid volumetric expansion occurs when product is heated above 100 C Material will sustain combustion for a short period until organic binder (and SAB coating) is burnt out or resulting expansion selfextinguishes. 10. STABILITY AND REACTIVITY STABILITY / CONDITIONS TO AVOID: MATERIALS TO AVOID: HAZARDOUS DECOMPOSITION PRODUCTS: 11. TOXICOLOGICAL INFORMATION Stable. Strong oxidizing agents, strong alkalis and hydrofluoric acid. Combustion products are HRO, CO, COR and hydrocarbons. The International Agency for Research on Cancer (IARC) has classified Mineral Wool Fibre as possibly carcinogenic (Group 2B). 12. ECOLOGICAL INFORMATION This product will remain stable over time with the inorganic components remaining inert. 13. DISPOSAL CONSIDERATIONS Waste is not classified as a hazardous waste and may be disposed of at a normal licensed industrial waste site. Local regulations should be considered. Waste should be bagged or suitably contained for disposal to prevent any dusts being windblown during disposal.

6 14. TRANSPORT INFORMATION Not regulated for Transport. Ensure that dust is not windblown during transportation. 15. REGULATORY INFORMATION LABELLING DANGER CLASSIFICATION - CONTAINS: - R PHRASES: - S PHRASES: - NATIONAL REGULATIONS: OTHER INFORMATION Further information regarding working with man-made mineral fibres and measurement techniques may be obtained by referring to Guidance Note EH and NDHS published by the UK, Health & Safety Executive. *The information contained in this safety data sheet is given in good faith. It is accurate to the best of our knowledge and belief and represents the most up to date information. The information given in this data sheet does not constitute or replace the user s own assessment of workplace risk as required by other health and safety legislation.