Stained Glass Mission-Style Frame A stained glass project
|
|
- Stewart Bell
- 5 years ago
- Views:
Transcription
1 Stained Glass Mission-Style Frame A stained glass project
2 Stained Glass Mission-Style Frame A Stained Glass Project PROJECT TITLE: Stained Glass Mission-Style Frame SKILL LEVEL: (Adult 1-5: 1 being the easiest, 5 being most difficult) 2 TIME TO COMPLETE: 1 Day PROJECT TIP: If solder does not flow smoothly apply more flux. If seams bulge over the glass there is too much solder you may need to melt and pull off the excess. If solder spits or bubbles there s too much flux wipe some off. Flat seams need more solder. Don t stay in the same spot too long or the solder will bleed through or the glass will crack. Wipe your iron tip frequently on a wet sponge while you are soldering. Do not leave the soldering iron in one place to long; this can crack the glass or the solder can melt through. This means the solder will liquefy and fall through the foil seam between the glass pieces. You can put masking tape under the seam. This will prevent it from falling through. Remove the tape right away. VENDOR NAME: Diamond Tech Crafts INSTRUCTIONS: Step 1 PREPARTION 1. Begin by placing your tools on a sturdy, flat work surface in a well-ventilated area. Opening a window or using a fan will aid in creating a well-ventilated work area. Choose a work area where the project can rest undisturbed by children and pets. NOTE: Limiting the movement of a project will limit damage. Homosote board is a good work surface and can be purchased at a local building supply store.
3 2. Clean each piece of glass thoroughly with rubbing alcohol and a clean cloth. NOTE: Foil will not stick properly if your glass is not free from grim or oils. 3. Layout your glass pieces on your pattern. Number each piece of glass with a marker so that it corresponds to the numbers on the pattern. Step 2 FOILING 1. The foil is what makes the solder adhere to the glass. Peel back 2-3 of backing from the foil, hold glass with the edge toward you, and apply foil to glass so that it extends evenly over both sides of the glass. Crimp (fold) over edges making sure to fold corners neat and flat and even on both sides. 2. Burnish or rub flat foil using fid, pencil or Popsicle stick. Burnish the outside edge first, then the corners. Do not scrub, as you may rip the foil. 3. Use a craft knife (or sharp blade of any kind) to trim any excess foil creating a uniform edge along the face of the glass. Completely wrap the perimeter of the glass without leaving gaps. 4. Lay foiled piece over corresponding area on the pattern. Step 3 SOLDERING 1. Plug in your soldering iron and place on work surface. 2. Re-align foiled glass pieces on pattern. Use metal push pins around the perimeter of the glass to hold them in place. 3. Apply a small amount of flux to copper foiled pieces. Too much flux will cause your seams to dull and oxidized over time. Apply flux only to areas that will be soldered within 10 minutes. Solder will not properly adhere to glass without foil and flux. 4. Pull out about 9 inches of solder from the spool. Do not cut it from the spool. 5. Hold soldering iron as you would a carving knife. Place the hot iron tip on the seam you want to solder. Place the solder from the spool about ½ up from the end of the soldering iron tip and gently push the solder into the tip, letting up on the amount of solder when you come to the end of the seam. Now wipe your tip on a wet sponge and put the iron back into its stand. 6. Completely solder seams by holding iron tip on the foil, perpendicular to the seam. Feed the solder into the tip as you move along the foil. 7. Allow project to cool, remove pushpins and flip, flux and solder all seams as on the front. NOTE: It is not necessary to tack solder the back. When flipping project over be careful; any straight edges/seams can act as a hinge and pull foil away from the glass. 8. To add an easel back to the frame, cut a length of wire 15 inches long. Bend and shape the length of wire form a U. Place the open edge of the U on the solder lines on either edge of the clear glass in the center of the frame. Apply a small amount of flux to the wire and tack solder into place. Now bend the U once again to form a L. The short leg of the L will rest on the counter and act as an easel back of the frame.
4 9. Wash glass thoroughly using warm water, soap and a soft brush when completely cooled. Clean both sides rinse well and dry. CAUTION: 1. Wear safety goggles when using glass crafting tools. 2. When working with glass, protect your feet and legs by wearing pants and closed toe shoes. 3. Soldering iron is extremely hot! Never touch the barrel or tip after the iron has been turned on. 4. Keep work area safe; use a heat resistant work surface or a soldering iron stand to rest your tool. 5. Never cool tool by dipping it into water. 6. Adult supervision should be used at all times for children under 13 years of age. 7. Use in a well ventilated area. SOLDERING IRON WARNING: A soldering iron is used in the application of lead solder which is known to the State of California to cause cancer, birth defects or other reproductive harm. Ingestion or inhalation of fumes or particles could cause lead poisoning. Use only with proper ventilation. Wash hands thoroughly before eating, drinking or smoking. SOLDER WARNING: HIS PRODUCT CONTAINS LEAD. Ingestion or inhalation of fumes or particles released through processing could cause lead poisoning. Absorption of lead may result in damage to the blood and neurological systems. Use only with adequate ventilation. Use NIOSH approved respiratory protection when necessary. Wash thoroughly before eating, drinking or smoking. KEEP OUT OF REACH OF CHILDREN. Not for use in potable water systems. See Material Safely Data Sheet for further information. LEAD -CAS# Tin - CAS #
5 MATERIALS CHECKLIST: Stained Glass Sheets 1 Each: Clear Royal (G136) Grass (G180) Purple (GA146) Beige Opaque (G317) 50/50 Solder Flux Brush (to apply flux) 7/32 Black-lined Foil 12 ½ ft - 14 Gauged Wire Heat Resistant Work Surface Pencil or Popsicle Stick Pliers Soldering Iron Metal Push Pins Vinegar Soft Cloth Liquid soap Scissors Fan
6
Turkey Football Panel
Turkey Football Panel PROJECT TITLE: Turkey Football Turkey Football Panel A Stained Glass Project DESIGNED BY: Jeanne Baruth for Diamond Tech SKILL LEVEL: (Adult 1-5 1 being the easiest, 5 being difficult)
More informationInstructions: Beginning Stained Glass
BASIC TYPES OF GLASS Cathedral - clear or colored see through glass Wispy/Translucent - clear glass with opal streaks Opal - glass that allows light through but cannot be seen through I. CUTTING AND BREAKING
More informationA Precision 2000 Mixed Media Project
Día de los Muertos (Day of the Dead) Panel A Precision 2000 Mixed Media Project PROJECT TITLE: Día de los Muertos (Day of the Dead) Panel DESIGNED BY: Andy Spencer SKILL LEVEL: (Adult 1-5: 1 being the
More informationSolder is a metallic glue that holds the parts together and forms a connection that allows electrical current to flow.
Proper Soldering & Desoldering High Performance Ultrasonic Range Finders Techniques of a MaxBotix Sensor Materials Needed for Soldering Goggles Hands-free clamp Wire stripper Soldering iron with stand
More informationInstruction for applying the Logo Decals
Instruction for applying the Logo Decals Supplied: *One set of N/C cut vinyl decals (one right and One left) (Note: packaged with the contoured wing tip plans) Items required to apply the decals (not supplied):
More information5 WEEK Beginning Stained Glass Class
5 WEEK Beginning Stained Glass Class Ed s Emporium Stained Glass Studio 2200 Barksdale Blvd Suite A Bossier City, Louisiana 71112 www.edsemporium.com 318-742-6555 Welcome! We hope that you will enjoy the
More informationCornerstone Electronics Technology and Robotics I Week 19 Soldering Tutorial
Cornerstone Electronics Technology and Robotics I Week 19 Soldering Tutorial Administration: o Prayer o Turn in quiz o Using fixed resistors design and build a voltage divider divides 5 volts in half.
More informationQUASAR ELECTRONICS KIT No DRILL SPEED CONTROLLER
QUASAR ELECTRONICS KIT No. 1074 DRILL SPEED CONTROLLER General Description If you work with an electric drill and unless you are lucky enough to own one of the most sophisticated models with speed control,
More informationInstallation Guide. Aspect Stone Peel & Stick Tile. proper surface preparation is essential for a successful project. Installations Methods
Aspect Stone Peel & Stick Tile Installation Guide E proper surface preparation is essential for a successful project Failure to follow recommended surface preparation instructions may void the warranty.
More informationSOLDERING MANUAL A simple, yet easy to follow manual for your basic soldering needs. Copyright 2017 TortugaPro. All Rights Reserved
A simple, yet easy to follow manual for your basic soldering needs Copyright 2017 TortugaPro. All Rights Reserved Purpose Soldering is not limited to electrical and electronics work. It is a skill that
More informationSolder Technique Studio Soldering Iron Fundamentals for the Mixed Media Artist
Solder Technique Studio Soldering Iron Fundamentals for the Mixed Media Artist Giuseppina Josie Cirincione north light books CreateMixedMedia.com Cincinnati, Ohio Materials Basic soldering tool kit Solder,
More informationSurprises with Light JoAnne Dombrowski
SCIENCE EXPERIMENTS ON FILE Revised Edition 6.29-2 Figure 1 3. Hold the card with the arrow in front of you at the same distance as the far side of the jars. From this position, move the card away from
More informationUser s Manual SOLDERING STATION
User s Manual SOLDERING STATION ASE-1111 Thank you for choosing AKTAKOM soldering station. www.tmatlantic.com Please note the following safety notes to avoid malfunctions, damage or physical injury: Persons
More informationEerie Halloween by Nunn Design
Eerie Halloween by Nunn Design Approximate finished length: 20 inches Beads and other products needed for necklaces: 1 - Pewter Itsy Square Bezel Pendant with Flat Loop by Nunn Design - Antique Gold -
More informationMission Embossible. Tools. Materials: Copper sheeting Ammonia Pickling vinegar Newspapers Copper powder Nail polish or shelac
Mission Embossible Jazz up your décor with copper Materials: Tools Copper sheeting Ammonia Pickling vinegar Newspapers Copper powder Nail polish or shelac Stylus Abrasive scrub pad Nail Scissors or tin
More informationSailcloth Fabric Replacement Top and Doors Installation Instructions
Sailcloth Fabric Replacement Top and Doors Installation Instructions For: Wrangler/TJ 1997-2002 Part Number: 79121 This product is only designed for the vehicles listed above. DO NOT INSTALL THIS PRODUCT
More informationPercy Pumpkin Head Light A KraftyBlok project.
Percy Pumpkin Head Light A KraftyBlok project. DESIGNED BY: Jeanne Baruth for Diamond Tech SKILL LEVEL: (Adult 1-5: 1 being the easiest, 5 being most difficult) 3 TIME TO COMPLETE: 2 hours not including
More informationGENERAL SOLDERING PROCEDURE
College of Engineering Laboratory Procedure GENERAL SOLDERING PROCEDURE Dept: Multi-department Laboratory: Multi-lab Rm: Multi-lab Authored by: Dick Sevier, Lab Support Engineer Date: Reviewed and Approved
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Roush Mustang Rear Valances This kit is intended for professional installation. Roush Performance 28400 Plymouth Road Livonia, MI 48150 1-800-59-ROUSH Application: Mustang 1999
More informationRepairing your Porsche 928 Central Warning System (CWS) controller
Repairing your Porsche 928 Central Warning System (CWS) controller Disclaimer: This procedure is for a 1984 Porsche 928 S controller. Overview: Under the left foot pedal (dead pedal) of the Porsche 928
More informationStandard Kit #1 (3-way switch)
Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationModel the hub of your layout s rural setting. Planters Feed and Seed Supply Instructions N Scale 1:160 WOODLAND SCENICS
PF5201 Planters Feed and Seed Supply Instructions N Scale 1:10 Model the hub of your layout s rural setting. Planters Feed and Seed Supply presents a vintage agricultural center where farmers and rural
More informationELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS Lesson 13 EET 150 Electrical Connections Learning Objectives In this lesson you will: see different methods of making electrical connections. learn a procedure for making soldered
More informationHalf Door Installation Instructions
Half Door Installation Instructions For: CJ7, CJ8/Scrambler and Wrangler/YJ Part Number: 53028 Note: Wrangler/YJ Use of this product may not allow use of factory side mirrors. Note: Wrangler/YJ Use of
More informationHalf Door Installation Instructions
Half Door Installation Instructions For: CJ5 (1955-1975), CJ6 (All), M38-A1 (1955-1971) Part Number: 53025 WARNING This product is designed primarily to enhance the appearance of the vehicle and to shield
More informationDASH KIT INSTALLATION
ÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿ ÿÿÿÿÿ ÿÿ ÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿ ÿÿÿÿ ÿÿ ÿÿÿÿÿ ÿÿÿÿÿÿÿÿ PROUDLY MADE IN THE USA DASH KIT INSTALLATION These instructions are aimed at the do-it-yourself installer. Read
More informationPalladian/ Keystone Models 202/204 Maintenance Kit
Palladian/ Keystone Models 202/204 Maintenance Kit Please read all of the instructions before you begin. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete
More informationInduction Heater Coil Kit Compact low voltage, high current induction coil
Induction Heater Coil Kit Compact low voltage, high current induction coil Model: CT-400-KIT Features and Specifications High power water cool-able copper coil PCB Layout designed to reduce eddy losses
More informationFender Protectors. To ensure a successful installation, please read all of these instructions prior to starting.
Fender Protectors To ensure a successful installation, please read all of these instructions prior to starting. General Instructions All Tough Stuff Protective Products use a waterproof contact adhesive.
More informationINSTALLATION INSTRUCTIONS
VESDURA VINYL PLANKS 3MM PVC GLUE DOWN - OAK COLLECTION Safety First CAUTION Asbestos Warning in existing floor. Do not sand, dry scrape, bead blast or mechanically pulverize existing resilient flooring.
More information1 SELECT suitable material. It takes time to cut a cab. Don t waste it on rubbish.
7 July 09 CUTTING A STANDARD CABOCHON A Standard Cabochon or CAB is an oval or round stone with one flat side and the other side having an even curved dome shape. Top of Cab It will have a narrow bevel
More informationSailcloth Fabric Replacement Top and Doors with Tinted Side and Rear Curtains Installation Instructions
Sailcloth Fabric Replacement Top and Doors with Tinted Side and Rear Curtains Installation Instructions TM For: Wrangler / TJ 2003 - Current Part Number: 79129 Inc. This product is only designed for the
More informationRepairs. Chapter 10 Repairs 10. 1
10 Repairs Chapter 10 Repairs 10. 1 Repairs As an installer, you will probably be called upon to repair damage to a resilient floor. Here are some of the most common problems and the recommended repairs
More informationIntroduction to Soldering
Introduction to Soldering The Soldering Iron American Standard Wire Gage (AWG) Solder The Soldering Process Stripping & Tinning Wire Connecting/Soldering Wire Component Soldering De-Soldering Lab Exercise
More informationSoldering & De-soldering
Soldering and De-soldering Digital Electronics 04 Soldering & De-soldering This presentation will Review the tools needed to solder and de-solder electronic components. Demonstrate how to tin a soldering
More informationXyron Professional 2500 Laminating System
Xyron Professional 2500 Laminating System Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com U S E R S G U I D E 2500 Adhesive Application & Laminating System The XM2500
More informationIntroduction. Pictures in this lab have been taken from Pre-Lab Homework
Introduction This lab relates to material in Hecht, Chapter 18. In this lab you will explore the concepts of circuits, resistors, and capacitors, by actually building a small circuit that is yours to keep!
More informationDIY Shaving Cream. Ingredients:
DIY Shaving Cream Ingredients: 1/3 cup coconut oil (solid, not fractioned) 1/3 cup shea butter ¼ cup sweet almond oil 4-6 drop tobacco bay leaf fragrance oil Plastic bale jar Tools: Microwave-safe bowl
More informationPacific Antenna SLT+ Switched Long wire Tuner
Pacific Antenna SLT+ Switched Long wire Tuner The SLT+ is designed to match the high impedance load of an end feed, half wave antenna wire to a 50 ohm transmitter using manually switched inductors and
More informationFabric Replacement Top and Doors
Fabric Replacement Top and Doors Installation Instructions For: Wrangler/TJ 1997 and Newer Part Number: 51131 WARNING This product is designed to enhance the appearance of the vehicle and to shield the
More informationSupplies WARM AND NATURAL COTTON BATTING FIBER FILL STUFFING COTTON PRINT FABRIC FOR DRESS OLD LIGHT WEIGHT SWEATER TO CUT UP SMALL PIECE OF MUSLIN FOR CANDY RABBIT PLAID-APPLE BARREL NUTMEG BROWN CRAFT
More informationWELDING. Section nine 9.1 CORRECT TOOLS
Section nine 9.1 CORRECT TOOLS WELDING Polyflor strongly recommends vinyl sheet and 608mm vinyl tile floorings are welded, this includes the internal and external joints when the vinyl sheet is site cove
More informationApplication of 3M Pressure Sensitive Films to 3M Panagraphics Substrates
Instruction Bulletin 5.30 Release B, Effective October 2006 See bulletin change summary on last page Application of 3M Pressure Sensitive Films to 3M Panagraphics Substrates Preparation Points to Consider
More informationHow to Install EZ Snap Window & Skylight Shades
How to Install EZ Snap Window & Skylight Shades Congratulations on your purchase of EZ Snap Shades You ve taken the first step in reducing your energy consumption, while blocking harmful UV rays, unwanted
More informationMirrorcraft Project Especially for Dogs
Mirrorcraft Project Especially for Dogs DIY Customized Pet Mirror Make a mirror photo frame to Display your Pets Photo Irene Jacobs April 2007 Mirrorcraft is a fun craft to easily create you own customized
More informationSPACER APPLICATION: KEY POİNTS FOR HİGH QUALİTY İG UNİTS
SPACER APPLICATION: KEY POİNTS FOR HİGH QUALİTY İG UNİTS Application of spacer should be in clean and indoor area. Glass washing machine, hot press machine and spacer application table should be in the
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationInstalling Digital Wallcoverings
Installing Digital Wallcoverings Hints & Tips Muraspec Digital (Hints & Tips) 1 BEFORE YOU START Make sure that your image is intact and has not been damaged in transit. For best results, use only Murabond
More informationBB Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
BB07552 5 Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.
More informationPractical Information: ORALITE V98 Conformable Graphic Sheeting
Page 1 of 5 General Information (hereto referred to as V98) is a tough, weather and solvent resistant product designed for graphics applications on vehicles with smooth painted or unpainted surfaces. Templating
More information675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure
INSTALLATION INSTRUCTIONS 675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure Call Technical Dept @ 1-800-452-2726 QCI1003 Page 1 of 9 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully
More informationFlex Fence Instruction Manual
The Safer Stronger Smarter Choice Flex Fence Instruction Manual Table of contents 2 3 4 4 5 5 6 7 8 10 10 11 11 12 13 13 15 18 18 19 20 22 Table of contents Supplies, tools and equipment Introduction Laying
More informationCardboard Model Buildings
Cardboard Model Buildings Get more model kits from http://www.modelbuildings.org PRINTING & ASSEMBLY TIPS: These OO designs can easily be resized by reducing the print percentage as follows: OO scale is
More informationIntroduction to Soldering Electronic Circuits
Introduction to Soldering Electronic Circuits Department of Electrical and Computer Engineering Kettering University Soldering Tools and Supplies Good quality pencil-type soldering iron Small gauge resign
More informationElectronics Merit Badge Class 4. 12/30/2010 Electronics Merit Badge Class 4 1
Electronics Merit Badge Class 4 12/30/2010 Electronics Merit Badge Class 4 1 Soldering Safety Note: A Soldering Iron gets hotter than 374 F. Do not touch the soldering iron s metal parts or you will receive
More informationArt of Ancient Times, Studio 1 5
Art of Ancient Times, Studio 1 5 Creating a Clay Relief Sculpture and an In-the-Round Sculpture In this studio you will make a relief sculpture and an in-the-round sculpture inspired by those created by
More informationStandard Kit #1 (5-way switch)
Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationThreads n Scissors. Easy Flip Flops
Easy Flip Flops Method Hoop 2 layers of water soluble stabilizer. Cut a piece of 1 mm thick 3D foam to fit the inside of the hoop. Put the foam onto the stabilizer and stitch out the design. Materials
More informationPremium Soldering station
www.jbctools.com English Premium Soldering station Ref. DIT-D 2 www.jbctools.com Packing List The following items should be included: DI Control Unit... 1 unit Stand... 1 unit Sponge... 1 unit Cartridge...
More informationOpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV
OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationCoat Rack. Materials: Directions:
Coat Rack 2x2 wooden poplar (foundation of the rack) 3/4 inch diameter wood dowels (5-8 depending on how many arms you want) 1/4 inch dowel screw 1/4 inch drill bit Power drill Ruler Pencil Paint/spray
More informationMagnetpaint & Sketchpaint
Magnetpaint & Sketchpaint Turn any smooth surface into a magnetically receptive whiteboard MagnetPaint is an exciting product that allows you to paint your own magnetic surface on any flat area. SketchPaint
More informationThere are three primary units to this box: two three-sided trays (one made to fit over the other) and one case that wraps around the trays.
Instructions for Basic Drop-Spine Box by Sandra Liddell Reese There are three primary units to this box: two three-sided trays (one made to fit over the other) and one case that wraps around the trays.
More informationCurium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationMixed Metal Heart Author: Patti Bullard Ph.D.
Mixed Metal Heart Author: Patti Bullard Ph.D. Mixed Metal Heart Difficulty: Easy The beauty of mixed metals paired with a traditional heart shape is sure to bring joy to the jewelry maker as well as the
More informationMustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions
Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions The below installation instructions work for the following products: Mustang Eleanor Style Louvers - Pre-painted (05-10)
More informationStop! Read This Important Information.
Stop! Read This Important Information. Stop, Do Not Proceed, Read This This door replacement kit is designed for the replacement of doors on a Supertop ONLY! This door will not work on any other style
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Assembly and Instruction Manual Elenco
More informationWEEKLY ACTIVITY GUIDES: ENERGY & ELECTRICITY
WEEKLY ACTIVITY GUIDES: ENERGY & ELECTRICITY This week, we ll be learning about electricity with hands-on experiences that show how energy works in the world around you. You can t see, smell or touch electricity,
More informationTechnical Specifications - Characteristics
Watt FM TRANSMITTER General Description This is a small but quite powerful FM transmitter having three RF stages incorporating an audio preamplifier for better modulation. t has an output power of 4 Watts
More informationMetal clay. Skill Set. Whether you want to learn how to bezel-set a cabochon, Step Up Your. earring project.
PROJECT INTERMEDIATE METAL CLAY Step Up Your Metal clay Skill Set Improve your craft à la carte in this technique-packed earring project. by Deb Fitz FCT-CRON0216_ART48 Whether you want to learn how to
More informationSoldering and Desoldering Instruction
Soldering and Desoldering Instruction Soldering is defined as "the joining of metals by a fusion of alloys which have relatively low melting points". In other words, you use a metal that has a low melting
More informationProduct Features. How to use polymorph
Specification: Density(g/cm3 25 C) : Approximately 1.10 Extensible and reusable, the melting point is 60-63 and can be shaped in low temperature. Will be released to CO2 and H2O during 6-12 months. When
More informationFirework Colors. 5 g each of the following compounds (in finely powdered form):
Firework Colors Topic Using the flame test to identify different metals Introduction Scientists use the flame test to distinguish between compounds containing different metal ions, such as sodium in sodium
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationPress and Media Tower PHOTO REAL BUILD KIT Innovative Hobbies Making Traditional Hobbies Better!
Press and Media Tower PHOTO REAL BUILD KIT Innovative Hobbies Making Traditional Hobbies Better! INSTRUCTIONS for Kit # BK 6424 Free replacement parts are available simply by calling or by simply emailing
More informationFootball Silhouettes Project Sheet 1 of 2: Classic Beads
Project Sheet 1 of 2: Classic Beads This project as shown at left has 4 designs 2 in classic beads and 2 in mini beads. They are intended to be displayed together; however, you may choose to make only
More informationSoldering is easy. here's how to do it. Andie Nordgren (Comics adaptation) Jeff Keyzer. by: Mitch Altman (soldering wisdom) (Layout and editing)
Soldering is easy here's how to do it by: Mitch Altman (soldering wisdom) Andie Nordgren (Comics adaptation) Jeff Keyzer (Layout and editing) Download this comic book and share it with your friends! Distribute
More informationWarning: CHOKING HAZARD -Small Parts. Not for Children Under 9 yrs. Kit Recommended for Ages 12 and up.
The Original Warning: CHOKING HAZARD -Small Parts. Not for Children Under 9 yrs. Kit Recommended for Ages 12 and up. Table of Contents Soldering.. 3 How the WASP Works.. 7 The Build...... 12 Troubleshooting......30
More informationHalf Door Installation Instructions
Half Door Installation Instructions For: CJ5 (1955-1975), CJ6 (All), M38-A1 (1955-1971) Part Number: 53025 Congratulations on your purchasing decision. Bestop designed these Doors to give you years of
More informationSwift assembly guide
Swift assembly guide Download the assembly guide at www.scihighmodels.com/swift.pdf Sample kit shown with aluminium bells (available with the Deluxe kit) Shown here without main tanks Version 10/12/2010
More informationInstalling Your New Creature From The Black Lagoon Tail Light DMD Panel MOD
Installing Your New Creature From The Black Lagoon Tail Light DMD Panel MOD A few things before we start: The wooden speaker panel provided in this MOD was manufactured using a Precision CNC machine and
More informationLED Thin Frame Fixed Frame Screen User Guide
LED Thin Frame Fixed Frame Screen User Guide INTRODUCTION INTRODUCTION WARNING - Sharp Edges This product may contain sharp edges, please handle with care. Protective gloves are recommended. WARNING -
More informationAdhesive Application & Laminating System
U S E R S G U I D E Adhesive Application & Laminating System The XM2500 is an economical and easy to use document finishing system. This versatile and non-electric system has been designed to laminate
More informationPlease read through the entire document before starting your installation process to better understand what is required.
1 P a g e How s It Hanging? Step-by-Step Guide for Hanging your Wallpaper Walls Republic offers a richer and wider selection of designs, textures and colours than ever before found in the wallpaper world,
More informationA complete collection of information about installing a Dana Decals vinyl decal.
INSTRUCTIONS COMPLETE COLLECTION CONTENTS: 1 2 3 4 5 6 7 8 Diagram of a Decal Detailed Transferring Tips Small Decal Installation A complete collection of information about installing a Dana Decals vinyl
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationBasic Stenciling Techniques
Metal Stencil Techniques For each technique you ll need the equipment listed in addition to your stencil and removable tape. To avoid bending your stainless steel stencils, keep them flat at all times.
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationReusable Tote Pattern
Reusable Tote Pattern Thank you to our wonderful zoo volunteer, Dawn Smith, for sewing hundreds of reusable totes, for providing the pictures and creating the instructions for this pattern. Using this
More informationDubnium 11 Installation Instructions & Parts List
Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.
More informationHARRISON S HARDWARE PF5891
1:48 BUILDING KIT HARRISON S HARDWARE PF5891 Model the local hardware store where layout residents can find all they need to keep their homes in tip-top shape and workshops running smooth. The positive
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationArduTouch Music Synthesizer
ArduTouch Music Synthesizer Assembly Instructions rev C Learn To Solder download for free at: http://mightyohm.com/soldercomic The following photos will show you how to solder. But feel free to download
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationSeries----SP3600A SHOWER DOOR
Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationMaterials: Preparing your materials: Use your towel to protect your work surface. Layout one length of bubblewrap, bubbles facing up.
These instructions show the layout and techniques for making flat circular art pieces. Follow these basic steps used to create a strong, even, wool felt surface. This is the base or canvas, open to embellishment
More information