INSTALLATION INSTRUCTIONS

Transcription

1 FlexCore Guardrail INSTALLATION INSTRUCTIONS Components End Post Kit GR-K-END Mid Post Kit GR-K-MID Core Kit GR-K-COR Top Rail GR-C-RAL Lower Rail GR-C-EXT Template GR-C-TMP Tools Required Tape Measure Marker Chalk Line Rotary Hammer Masonry Drill Bit 5/8 [16mm] 1 [25mm] Corded Drill 15/16 Socket & Extension 7/32 Hex Key Drill with 7/32 Hex Bit? Questions McCue Corporation Peabody, Massachusetts, USA +1 (800) customercare@mccue.com McCue UK & Europe Milton Keynes, United Kingdom +44 (0) uksales@mccue.com mccue.com McCue Asia Xiamen, Fujian, China FlexCore Guardrail Page 1 of 9

2 Modular Product This is a modular Guardrail System and each installation requires it's own custom layout. Please read entire installation instructions before beginning your installation. If you require additional information, please contact McCue Customer Care for assistance. Template Instructions Use the included template to accurately mark hole locations for drilling. Steps that require the template will be labeled the template icon. Template Use template for this step Flange Hole Mark 1" [25mm] Drill Bit 6.00in [152mm] Center to Flange Anchor Hole Mark 5/8" [16mm] Drill Bit 1.50in [38mm] Center to Anchor Center Anchor Hole Mark 5/8" [16mm] Drill Bit Flange Hole Mark 1" [25mm] Drill Bit Alignment Marks FlexCore Guardrail Page 2 of 9

3 1 Attention: If section is less than 10' center to center, see cutting instructions 2 TOP VIEW 120in 3048mm Center hole to center hole + Template & Tape Measure + Chalk Line! Template Use template for this step Attention: Make sure the barrier hole and flange markings line up properly 3 1 in [25mm] END POST TOP VIEW MID POST TOP VIEW 3.00in [75mm] 1" Diameter Flange Hole 3 [75mm] 1" Diameter Flange Hole 3 [75mm] 5/8 in [16mm] 5/8" Diameter Anchor Hole 5.5 [140mm] 5/8" Diameter Anchor Hole 5.5 [140mm] 5.5in [140mm] 5/8" Diameter Anchor Hole 5.5 [140mm] 5/8" Diameter Anchor Hole 5.5 [140mm] 1" Diameter Flange Hole 3 [75mm] + Rotary Hammer with 1 & 5/8 Drill Bits FlexCore Guardrail Page 3 of 9

4 4 + Impact Driver with 15/16 Socket 5 5/8 Anchor Washer Damper Aluminum Pin Core Flange 6 7! + 7/32 Hex Key Attention: Start thread by hand. Do not cross thread! Drill Optional. FlexCore Guardrail Page 4 of 9

5 8 End Post: Go to step 14 Mid Post: Continue to next step 9! Attention: If rails are not at the desired length, see cutting instructions + Template & Tape Measure 120in 3048mm Template Use template for this step FlexCore Guardrail Page 5 of 9

6 MID POST TOP VIEW 6 in [152 mm] 6 in [152 mm] in [38mm] 1.50in [38mm] 1" Diameter Flange Hole 3 [75mm] 5/8" Diameter Anchor Hole 5.5 [140mm] 5/8" Diameter Anchor Hole 5.5 [140mm] 1" Diameter Flange Hole 3 [75mm] + Rotary Hammer with 1 & 5/8 Drill Bits 11 FlexCore Guardrail Page 6 of 9

7 12 + Impact Driver with 15/16 Socket 5/8 Anchor Washer Damper Core /32 Hex Key! Attention: Repeat steps 9-13 until last post FlexCore Guardrail Page 7 of 9

8 14 + 7/32 Hex Key 15 FlexCore Guardrail Page 8 of 9

9 16 + 7/32 Hex Key 17 Installation instructions are provided for guidance only. The seller assumes no liability regarding improper installation or misapplication of its products. It is the installer s responsibility to check for proper installation and, if in doubt, contact McCue Customer Care for assistance McCue Corporation. Jun FlexCore Guardrail Page 9 of 9

10 FlexCore Guardrail EXTRUSION CUTTING INSTRUCTIONS Components Tools Required Top Rail GR-C-RAL Lower Rail GR-C-EXT Template GR-C-TMP Tape Measure Marker Chalk Line Corded Drill Saw 1 Step Bit? Questions McCue Corporation Peabody, Massachusetts, USA +1 (800) customercare@mccue.com McCue UK & Europe Milton Keynes, United Kingdom +44 (0) uksales@mccue.com McCue Asia Xiamen, Fujian, China mccue.com

11 1 Center hole to center hole + Template & Tape Measure Step 1: Measure to and place template at new core center. Use template to mark anchor holes and pin hole(s). 2 + Tape Measure Step 2: Measure distance between the pin hole and your newly marked pin mark. Cutting Extrusions to Length Page 2 of 6

12 3 Flange Hole Extrusion Cut Line 2 1/8in [54mm] + Tape Measure Step 3: On bottom rail extrusion, measure & mark new pin hole using dimension from Step 2. Mark new extrusion cut length at 2-1/8 [54mm] offset from pin hole mark. 4 + Drill with 1 Step Bit Step 4: Drill new Pin hole through bottom rail extrusion using a 1 step bit. Cutting Extrusions to Length Page 3 of 6

13 5 + Saw Step 5: Cut extrusion on new cut line. 6 TOP VIEW Measure Pin Center to Pin Center SIDE VIEW Step 6: Once custom-length bottom rail and both posts are installed, measure between pin centers. Cutting Extrusions to Length Page 4 of 6

14 7 Pin Hole Extrusion Cut Line 1.50in [38mm] + Tape Measure & Marker Step 7: On top rail extrusion, measure and mark new pin hole using dimension from step 6. Mark your new cutting line at 1.5 [38mm] offset from the new Pin hole mark. Mark on both top and bottom of extrusion. 8 + Drill with Step Bit Step 8: Drill through top and bottom wall of extrusion using a 1 step bit. Cutting Extrusions to Length Page 5 of 6

15 9 + Saw Step 9: Cut extrusion to length and install. 10 Installation instructions are provided for guidance only. The seller assumes no liability regarding improper installation or misapplication of its products. It is the installer s responsibility to check for proper installation and, if in doubt, contact McCue Customer Care for assistance McCue Corporation. Jun Cutting Extrusions to Length Page 6 of 6