DIY! How to Make Your Own. Trip Line Detonator for Use With Big Blast Target InflatorÔ
|
|
- Della Ward
- 5 years ago
- Views:
Transcription
1 IMPORTANT To ensure the templates print the correct size make certain that Scale or Scaling in your PDF printing program is set to Off or None. Trip Line Detonator for Use With Big Blast Target InflatorÔ Big Blast Target InflatorÔ trademark is owned by Umarex USA DIY! How to Make Your Own Made specifically for use with Big Blast Target InflatorÔ
2 How to modify a Rat Trap for use as a pressurized Cola bottle detonator SAFETY There is no inherent danger in building this device just keep in mind that smart people get hurt when doing stupid things. Pay attention, work smart and be safe. Use gloves, eye protection and hearing protection when handling pressurized bottles!! Cover the bottle with a heavy bath towel or rug while inflating. If any part of the bottle turns milky white or frosty looking while inflating Discard that bottle, it s defective!! Be certain that the Big Blast bottle cap is tied to something to ensure that it isn t driven by the blast into anything or anyone that can be damaged or injured. KEEP CHILDREN AWAY!! Trip Line Detonator for Use With Big Blast Target InflatorÔ Big Blast Target InflatorÔ trademark is owned by Umarex USA Tie Strap Holes (For Bottle Mounting) Page 2 Mounting Holes (Template on Page 10)
3 Designed for use with Big Blast Target InflatorÔ which is found in most sporting goods stores The intended usage of this device is to snap a firing pin into a high pressure bottle causing a deafening blast when the trip line is hit Very useful for keeping deer... prowlers and zombies away. WARNING: Do Not use indoors or in confined spaces as the extreme db noise level may cause hearing damage!! Please understand that we are showing the way we built the device and you may see a better way of doing it. In addition to the simplicity of the design you ll notice that absolute accuracy is not required. Getting close is good enough. The secret to making it work is to defeat the sensitivity of the tripping mechanism. This is done by using a twine leader a rubber band and a little slack in the twine as shown on page 7. The drawings are actual size and can be cut out and used as templates. (Pages 11 & 12) Why we ve chosen to use the Victor Metal Pedal Rat Trap Model #M201 (or Model M210) It s the only trap we ve found with a easily removed trigger. Simple to take off and get out of the way while we re drilling the holes and it reinstalls just as easy. Tools: Forstner Bits make nice clean holes but hole saws and spade bits can also be used. Sizes required: 1/4,, 1-1/4 A #12 Firing Pin screw requires a 5/32 bit. No size is specified for the mounting holes (Page 10) use what fits your screws. The only other tools needed are a sharp chisel or knife to remove material around 2 holes, a pair of wire cutters for trimming the tie straps, a small screwdriver to remove the trigger, needle nose pliers to re-install the trigger, and a spring clamp. You ll also need a saw to cut out the Firing Pin Adapter blanks. Material required: Plywood 3/16 (5mm) 2-1/4 x 4 inches. We re using 3/16 in. x 4 ft. x 4 ft. Multi-Purpose Project Panel Tri-PLY from Home Depot Model # It s moisture resistant but must be dipped in a water proofer like Thompson's to protect it. Rubber band 3-1/2"L x 1/4"W, #64 (same thing post office uses) Masons line or sturdy twine for the leader and another 6 feet to secure the Big Blast cap. S hook A tiny Carabiner Hook makes attachment of the Trip Line to the trigger leader easy. Fishing line 8 lb test for trip line. 8 lb line is plenty strong enough to operate the trap and will break before doing any serious damage to the trigger. Sheet Metal Screw for firing pin (Pan head #12 x 1-1/4 ) The length is critical longer or shorter will not work. Tie Straps 11", 50 lbs, cheap at Harbor Freight Page 3
4 Firing Pin Adapter (not shown) will be Tie Strapped to the Hammer Hammer Spring Arm Bar TRIGGER BASE Terms Used Let s Build one! There are 3 Secrets to making this thing work: A Rubber Band, Slack in the Trigger leader and a properly positioned Firing Pin. And all 3 will be disclosed in the following pages!! STEP 1 Remove the Trigger so it doesn t interfere with the hole drilling... Place screwdriver in slot and twist to widen the slot. Lift trigger out. STEP 2 Print templates found on Page 11. Tape Template to Trap and mark hole locations with Punch or Awl Page 4
5 STEP 3 Remove template and drill holes. Remember to drill the hole before the 1-1/4 hole. Remove excess to dashed lines with chisel. STEP 4 Install Reinforcement to end of trap base. This step is optional but highly recommended as we ve found that some trap bases break the first time they re used. Cut a strip of wood 9/16" square by 3-1/4" long. Glue and screw as shown. STEP 5 Slot the trigger back in and bend the tab back up so it stays put. Page 5
6 STEP 6 Tape Template to the Firing Pin Adapter blank. Plywood 3/16 (5mm) 2-1/4 x 4 inches. Find templates on Page 12. This part is the most easily damaged therefore making 2 or more pieces is recommended. STEP 7 Mark Hole Centers, Remove template and drill holes, Shape to lines with chisel. Mark this part with a X or the word UP to make certain it s installed the right side up. When done dip the part in Thomson s Water Seal or boiled linseed oil to waterproof. Trip line (Normally 8lb fishing line -- masons twine shown in this example) Trigger Leader BIG SECRET reveled on next page!! STEP 8 Cut about a foot of twine for the Trigger leader and tie one end to a S hook. The optional Carabiner is tied to the Trip line and clipped to the S hook. The carabiner makes disconnecting the trip line easy. Second thoughts forget the S hook and just tie a loop in the end of the Leader. Page 6
7 Putting things together The SECRET to making this thing work starts here - It s the rubber band and slack in the twine! Without this slack a bird landing on the trip line would set it off. Mark 2-1/2 inches from knot on rubber band. STEP 9 Trigger Leader -One end has a S Hook or a loop tied on it- Tie the other end of the to the rubber band as shown. Leave a good 4-6 inches of the twine free at the end. Measure 2-1/2 inches from the knot and mark the twine, insert this mark in the trigger crimp. STEP 10 The end of the Trigger Leader is crimped to the trigger with 2-1/2" slack in the line. The twine doesn t have to be crimped tight, just enough drag to pull the trigger The Leader slack provides a buffer that allows movement of the trip line without setting off the trap. This slack prevents premature operation of trigger and you will adjust it to optimum. Hammer Firing Pin STEP 11 Don t tie a knot in the end of the twine because if the trip line is hit hard or fast the knot will prevent the line slipping out of the trigger causing damage to it. Melt the end of the twine to prevent unraveling. Page 7 STEP 12 Install the Firing Pin and then strap the Adapter onto the trap Hammer. Notice that the Firing Pin Adapter is installed under the Hammer and the tie strap clasps are at the top. If this Adapter is installed Wrong Side up the trap will not set.
8 STEP 13 Install bottle. The bottle can be installed on the work bench or after the detonator has been mounted to post or tree. Do Not use heavy duty tie straps, (less chance of breaking the trap) two 11 inch 50 pound straps on each side will do fine. When working at the workbench put around 50 psi of air in the bottle, and snug up the tie straps just enough to hold bottle in place, Not Tight because the bottle will swell when pumped up. After installing inflate to psi. When working outside the bottle will probably have to be installed at full pressure. STEP 14 Mount on tree Requires a 2x4 bracket as shown to hold the bottle clear of the tree. TREE Trip Line TREE Notice that the detonator and adapter have to be mounted on the other side of the tree. STEP 15 Mount on post Protect the bottle from the firing pin with a piece of thin wood while you re installing the mounting screws. Page 8 STEP 16 Install the trip line and clamp the trap open while you double check slack in the Trigger leader. The trip line must be allowed movement without setting off the trap. If your trip line is long or tight you may need to use a 2nd rubber band.
9 IMPORTANT The bottle cap must be secured to prevent its loss and to make certain that it isn t driven by the blast into anything or anyone that can be damaged or injured. Tie it to something using at least 6 feet of Masons twine. STEP 17 Pull gently on the Trip Line while observing the slack in the Trigger Leader. Just enough slack to set off the trap without undue force on the rubber bands. Adjust as necessary. STEP 18 Remove the spring clamp and set the trap as below: THIS SIDE UP Arm Bar Traps are meant to sit on the floor and cannot be set Firing Pin when horizontal unless there is something to support the Arm Bar. This is done here by laying the Bar across the Firing Pin and it won t work any other way. Make certain the trap is mounted the right side up!! Page 9
10 Your choice of size and location.v V What it looks like when assembled Parts shown in installed position Firing Pin Adapter Firing Pin Hole 0 1/2" These 3 holes are used for mounting... Your choice of size and location. 2" Cut this out and use to mark mounting hole locations 0 1/2" 1 5/8" RAT TRAP VICTOR This SIDE Mounts UP 2.75" Page 10 Layout of mounting holes shown above
11 RAT TRAP 1/4 1-1/4 1/4 Drill 2nd These areas to be removed with knife or chisel Drill this Hole 1st RAT TRAP 1/4 1-1/4 1/4 Drill 2nd These areas to be removed with knife or chisel Drill this Hole 1st RAT TRAP RAT TRAP 1/4 1-1/4 1/4 Drill 2nd These areas to be removed with knife or chisel Drill this Hole 1st RAT TRAP 1/4 1-1/4 1/4 Drill 2nd These areas to be removed with knife or chisel Drill this Hole 1st RAT TRAP 1/4 1-1/4 1/4 1/4 1-1/4 1/4 Drill 2nd These areas to be removed with knife or chisel Drill 2nd These areas to be removed with knife or chisel Drill this Hole 1st Drill this Hole 1st TRAP MULITPLE TEMPLATES Page 11
12 FIRING PIN ADAPTER, MULTIPLE TEMPLATES Page 12
Original Gallery System
GAllery System Art Displays Original Gallery System a Gallery System product Here s everything you need to know to get started with your Gallery System Art Hanging System GS getting started To install
More informationDATE: January, 01, 2011 AUTHOR: Craig Macomber TOPIC: Making and operating a model onager
DATE: January, 01, 2011 AUTHOR: Craig Macomber TOPIC: Making and operating a model onager INTRODUCTION This guide will walk you through the construction and operation of a hand held scale Roman Onager,
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More information* * APPLICABLE MODELS: 2014 > MAZDA 3
PART NUMBER: 0000 8C L46 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0604-000* APPLICABLE MODELS: 204 > MAZDA 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationFlex Fence Instruction Manual
The Safer Stronger Smarter Choice Flex Fence Instruction Manual Table of contents 2 3 4 4 5 5 6 7 8 10 10 11 11 12 13 13 15 18 18 19 20 22 Table of contents Supplies, tools and equipment Introduction Laying
More informationCautionary and Warning Statement. How a Trebuchet Works. Materials Included. Items Required (not included) Building the Base.
Cautionary and Warning Statement This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult who has read and understood the instructions provided
More informationElectrical Construction Name:
Tools of the Trade The following are common tools that are used in the electrical industry. This hand-out is to help familiarize you with the tools, the terminology, and their use. Retractable Steel tape
More information* Drill and 3/32" drill bit: for drilling holes in the factory plastic upper for the screws to secure the brackets (factory upper installation only)
* Two slider windows (four sliders windows for the 4-door kit) * Four brackets to secure the windows to the upper door frames (8 brackets for the 4-door kit) * Weatherstrip to seal the windows to the half
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More informationDRAFT. Sudden Ionospheric Disturbance (SID) Antenna Manual. Stanford Solar Center Stanford University Version 2.0
DRAFT Sudden Ionospheric Disturbance (SID) Antenna Manual Stanford Solar Center Stanford University Version 2.0 Construction and maintenance of your SID Monitor s Antenna TABLE OF CONTENTS DOCUMENT STATUS...2
More informationSCULL HANDLES AND GRIPS INSTRUCTION BOOKLET
SCULL HANDLES AND GRIPS INSTRUCTION BOOKLET Contents Section I: Scull Grip Replacement: Fixed Handle or 10 cm Length Adjustment System Refer to this section if you need to replace the grips on your fixed
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationPlug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions
www.lightorama.com Plug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions Read all instructions before you start Kit assembly! STEP 1. Check that all parts are included Parts
More informationWiring Techniques for Wiring a Lamp
Supplies and Tools that you will need: Provided in your kit: Polarized lamp plug, 9 of SPT-1 18 AWG parallel lamp cord, bushings and grommets Items that you will need to provide: Phillips screwdriver,
More informationHatchback Wing Riser Kit
Hatchback Wing Riser Kit 2015-06-11 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationMotorcycle Lift Assembly Instructions
Motorcycle Lift Assembly Instructions Copyright JCS 2009 Rev1M Page 1 Lift Table Assembly Instructions The following pages will assist you in the construction of your Motorcycle Lift Table. You will find
More informationPlastic Trainer-19. I have tried to only use materials available from the big box building centers like Home Depot, Rona (Canada) and Lowe s.
Plastic Trainer-19 I have tried to only use materials available from the big box building centers like Home Depot, Rona (Canada) and Lowe s. The picture above shows the prototypes with an original Cox
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationRPS. XR Front Drive Updates CORPORATION
FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and
More informationHow to install an aftermarket stereo/navigation
How to install an aftermarket stereo/navigation As most of you know, the 2002 (and others) Sport Trac has the 1 ½ DIN radio. This makes for some narrow choices when putting in a radio with navigation.
More informationSTEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:
DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart
PART NUMBER: 0000 8C R0 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0554-000* APPLICABLE MODELS: 203 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationAUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE
AUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE The keyless entry system in the D3 is a great feature. If you have the car key fob in your pocket, putting your hand under the door handle will unlock
More informationTortoise Switch Machines, Mounted Horizontally
Tortoise Switch Machines, Mounted Horizontally by David King Have you ever used the Tortoise Switch Machines manufactured by Circuitron. These are a wonderful stall motor slow motion switch machine that
More informationTools: Scissors, hand held single-hole punch, metal ruler or other good straight-edge, sharp knife or Exacto-knife.
Instructions for Building a Kepler Paper Model Version 30 Mar 3, 2010 You need the following files: File Sheet # Printer Paper Color Kepler_model_instructionspdf plain b/w Photometerpdf 1 Photo stock color
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-24 24 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 24 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationStream NXT - assembly instructions
Stream NXT - assembly instructions Recommended settings CG (measured from root leading edge): Speed/launch camber (+down, near the wing root): Cruise camber (+down, near the wing root): Thermal camber
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationCoat Rack. Materials: Directions:
Coat Rack 2x2 wooden poplar (foundation of the rack) 3/4 inch diameter wood dowels (5-8 depending on how many arms you want) 1/4 inch dowel screw 1/4 inch drill bit Power drill Ruler Pencil Paint/spray
More informationInstructions for the installation of Handy Well Pump Models HWP-E, HWP and HWP-L. **Read thoroughly before you start!**
Instructions for the installation of Handy Well Pump Models HWP-E, HWP and HWP-L. **Read thoroughly before you start!** Model HWP-E Model HWP Model HWP-L Congratulations! You have purchased a quality hand
More informationKromski Minstrel Assembly Instructions
Kromski Minstrel Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-12 12 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 12 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationPlastic Push. 5/16 Hex Head Bolt, 20 pcs. Retainer, 20 pcs. Female Bullet Connector, 4 pcs. Side Refl ex Refl ector, 2 pcs
A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according
More informationLEGENDS RETRACTABLE DOOR SCREENS
LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess
More informationRecaro sport seat strip down and rebuild
Recaro sport seat strip down and rebuild So why do this, well I managed to find a set of Recaro s left in a wet shed for over 25 years and Rather than pay for someone to strip these down i decided to have
More information1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs
97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with
More informationConnecting a Warp Feed to an Intelliframe
Connecting a Warp Feed to an Intelliframe So you want to trigger your Warp Feed every time you pull the trigger? Sounds like a great idea! This step by step picture story will guide you through this process.
More informationNotification System Installation Guide
Notification System Installation Guide NOTE: It is strongly recommend that you hire a licensed electrician to perform the installation of this product. Materials Provided 1. Directory Sign (1) a. Directory
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationMOTORIZED STANDARD SHADE WITH CABLES Installation Instructions
Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench
More informationExterior Door Handle - LH - Unpainted (05-14 All)
Tools Required: Exterior Door Handle - LH - Unpainted (05-14 All) 1) 10mm and 7mm sockets 2) Socket wrench (small size recommended) 3) T30 Torx bit 4) Plastic pry/molding tool (below, A) 5) Thin plastic
More informationVolvo 240/260 New Face Overlay Installation Models By Dave Barton
Volvo 240/260 New Face Overlay Installation 1975-80 Models By Dave Barton These custom faces are the product of years of research and experimentation. They are printed with a special printer using waterproof
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationTools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More informationSeries 1100 Aluminum Door Canopy
Series 00 Aluminum Door Canopy with Support Arms It is our recommendation that you read instructions carefully prior to assembly and installation. Series 00 with Support Arms MOUNTING BAR (A) TOP TRIM
More informationModule One: Non Powered Hand Tools
Module One: Non Powered Hand Tools What is included in this module Why are we learning this? Safety rules Right tool for the right job Identity of Tools Hands on time Quiz Why are we here? Basic knowledge
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 Front of Cabinet (closed) 1. Locking front door to User area. 2.
More informationRepair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION.
Replacing a La Z Time Mechanism Side Subassembly Tools Required: Slotted Screwdriver Power Driver 8" Driver Extension Ruler Note: Extension springs are not typically used on non-chaise standard width styles,
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More information5/16 Hex Head Bolt, 16 pcs. Plastic Push Retainer, 6 pcs. Alcohol Wipe, 2 pcs. Side Refl ex Reflector, 2 pcs
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationHow to install the Kreg Bench Klamp System with Klamp Plate on a workbench
How to install the Kreg Bench Klamp System with Klamp Plate on a workbench Posted by Vince M, www.zonetravaux.fr http://www.zonetravaux.fr/2014/01/pince-plaque-serrage-kreg-etabli/ I built my workbench
More informationCMA-455 Suspended Ceiling-Tile Reinforcing Kit
INSTALLATION INSTRUCTIONS CMA-455 Suspended Ceiling-Tile Reinforcing Kit The provides a sturdy support for LCD/DLP hanging brackets (and certain other products) when installing these products in a suspended
More informationHisun Deluxe Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual.
Owner s Manual Model: Hisun Hisun Deluxe Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab kit Contents Hardware Assembly Panel Assembly
More informationMetal Aircraft Landing Light Installation Instructions
Metal Aircraft Landing Light Installation Instructions This landing light kit was designed for the Thorp T-18 as a method of installing a halogen landing light in the leading edge of the outer bay of the
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationThis book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc.
Copyright 2006 - Stay Tooned, Inc. All rights reserved worldwide. This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay
More informationCable Hanging Instruction Manual
Tri-States Grain Conditioning, Inc. Cable Hanging Instruction Manual There are several types of grain storage tanks and bins. Parts of these instructions may be modified to fit the circumstances. Care
More informationTools Needed Hardware Provided (per shade) Hardware Needed
Baby Grande or Grande Motorized (XQ5 Premium) Shade with Cables and Housing Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit Measuring Tape
More informationSolara Adjustable Patio Cover Installation Instructions
Solara Adjustable Patio Cover Installation Instructions We divided the installation instructions in 6 major sections. Reference your project to the drawings below, this way you ll know you are on the right
More informationCentral New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
More informationDYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0
DYNATRAC PRODUCTS 2007-2016 4X4 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 WARNING: Improper use or installation of this product can cause major failures
More informationService Bulletin
Service Bulletin 18-026 April 24, 2018 Version 5 Safety Recall: Left (Driver Side) Second Row Seat Recliner Does Not Lock Supersedes 18-026, dated April 7, 2018 to revise the information highlighted in
More informationHow to build a Ram for Challenge E: Twist-O-Rama
How to build a Ram for Challenge E: Twist-O-Rama Notes The Ram is like the Structure Tester it is not Interference for a Team Manager or other non-team members to build it. Construction time is approximately
More informationSide "A" Stake here. Side "C" Side "D" Side "B" Here Shirley and I are setting up a 10 X 16 ground work.
Choosing the Location It is always best to locate your greenhouse so that it can receive maximum sunlight at all times of the year especially in winter months. If Possible orient the long side towards
More informationRazr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada
Razr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada The following is a description of the process that I have used to modify the console eject box for e38, e39, e46 and x5 s, part number 84-21-6-933-415.
More informationSUPPLIES: Hammer. are best) Perlon or Fish. pins to affix. on hand.
HOW TO INSTALL AN ART SHOW AT HO OMALUHIA: SUPPLIES: Hammer Picture Hanging hooks (better than nails) Optional: Nails are ok on hard walls (common orr box nails between 1 and 2 inches long are best) Level
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationLEGENDS RETRACTABLE DOOR SCREENS
I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess within the door jamb area. Recess installations are the most typically
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationSYSTEM 42 SCREEN CASSETTE WITH 30mm SIDE RAIL
LEGENDS VERTICAL WINDOW RETRACTABLE SCREEN SYSTEM 42 SCREEN CASSETTE WITH 30mm SIDE RAIL I N S T A L L A T I O N I N S T R U C T I O N NOTE: Screen components must be installed on a flat surface to ensure
More informationType 316SS Backed Conveyor Strip Brush Nylon Bristles, 6" O'all HT, 2' Lg, 3/16" Backing
How to modify your MK101. First off, the MK101 tile saw is a fantastic tile saw, without any modifications what so ever. That being said, all tile saws tend to have a significant amount of overspray which
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationPRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
HP PRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF-280A/X TONER CARTRIDGE REMANUFACTURING THE HP LASERJET PRO 400 M401/MFP M425 (CF-280A/X) TONER CARTRIDGE By Mike Josiah
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationPROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0
DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could
More informationReplacing Hammer Butt Springs in the Upright Action
Schaff Piano Supply Company Presents: Replacing Hammer Butt Springs in the Upright Action Basic Procedures By Chuck Behm Replacing Hammer Butt Springs -Rationale- In the restoration of an upright, the
More informationQuestions? Call us at or us at
Questions? Call us at 610-345-9044 or email us at admin@selectincrements.com Select Increments is not responsible for any defects with amplifiers, speakers, or wiring kits. If you experience any problems
More informationAR-15 Lower Receiver Assembly Instructions
AR-15 Lower Receiver Assembly Instructions Tools There are a few tools that make it easier to put together these kits, but none of them are necessary. Minimum requirements include a hammer and punch to
More informationBand-Master ATS Nano Pneumatic Banding Tool Operating Instructions
Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...
More informationSeries 1500 Aluminum Door Canopy
Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationThe Hamlin Assembly Instruction By Laser Dollhouse Designs
The Hamlin Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationRTI TECHNOLOGIES, INC.
RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally
More informationDYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0
DYNATRAC PRODUCTS 2007-2018 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0 WARNING: Improper use or installation of this product can cause major failures that
More informationATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013
ATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013 Atlantis Rail s HandiSwage System is an easy to use cable railing product utilizing
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationHOW TO MAKE LEATHER EXTENDERS KATIE BILZI NATURAL ENCOUNTERS, INC.
HOW TO MAKE LEATHER EXTENDERS KATIE BILZI NATURAL ENCOUNTERS, INC. MATERIALS NEEDED: Leather, cutting board, 6-gauge hole puncher, leather scissors, leather cutter or X-ACTO Knife, pliers (needle nose
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationMMD Convertible Styling Bar Customer Installation Guide
MMD Convertible Styling Bar Customer Installation Guide TOOLS REQUIRED/RECOMMENDED: Electric Drill 1 Forstner Bit (Hole Saw) 1 3/8 Hole Saw (manual calls for 1 ¾ ) 1/8, 3/8 & ¾ Drill Bits Rivet Gun Trim
More informationkiva design kiva design GARDEN TOWNS Bill's Water Tower
GREN TOWNS Scaled and easy to read patterns and instructions for a Water Tower made from wood, a 3 pound coffee can and a few sundry items. ompatible with Garden Scale Railroads and Kiva's GardenTowns
More informationYES 12 Charging Wall Cabinet for Mini-laptops
Built with Anthro-DNA Owner's Manual for YES 12 Charging Wall Cabinet for Mini-laptops Part # YESMLCGMPW Components at a Glance 7 1 9 8 2 4 5 11 6 10 3 Front of Cabinet (closed) 1. Locking front door to
More informationTechnicians of Terror. This is the air valve we make to use with our air
These are pictures of our scissor prop. Technicians of Terror http://www.halloweenfear.com/scissorprop.html props. This is the air valve we make to use with our air This pictures the duel door closer cylinders
More information