HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY

Transcription

1 WITH MOUNTING BRACKET PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION OF THIS. CONTAINED WITHIN IS THE TECHNICAL INFORMATION AND INSTALLATION TECHNIQUES REQUIRED TO COMPLETE AN EFFICIENT, NEAT AND LONG-LASTING INSTALLATION. INSPECT ALL MATERIALS FOR DAMAGE OR MISSING PARTS. IF YOU DISCOVER DAMAGED OR MISSING MATERIALS, IN THE USA PLEASE NOTIFY THE FACTORY AT (800) , AND IN CANADA (888) FOR CUSTOMER SERVICE. MUST BE INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS! FAILURE TO FOLLOW THESE INSTRUCTIONS MAY VOID ANY PRODUCT WARRANTIES AND RESULT IN AN UNSUCCESSFUL INSTALLATION. FOR SPECIFIC QUESTIONS REGARDING THE INSTALLATION OF THIS PLEASE CALL THE FACTORY IN THE USA AT (800) OR IWPTECHSUPPORT@C-SGROUP.COM. IN CANADA CALL (888) HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY 3" [76.2mm] 6 1/4" [158.2mm] 3 7/16" [86.8mm] SECTIONAL VIEW 1 1/2" [38.1mm] IMPORTANT NOTES 1. ALL LINEAL MATERIAL TO BE SUPPLIED IN STOCK LENGTHS. ALUMINUM AND ACROVYN IN LENGTHS UP TO 20'-0". THIS MATERIAL IS TO BE FIELD CUT USING QUALITY EQUIPMENT TO INSURE THAT ALL CUTS ARE SQUARE. WHEN CUTTING MATERIAL SECTIONS, C/S RECOMMENDS USING AN TOOTH CARBIDE TIPPED SAW BLADE OR EQUIVALENT, TO MINIMIZE CHIPPING AND MAINTAIN JOINT ALIGNMENT. 2. ALL DIMENSIONS ARE TYPICAL. 3. FOR DRYWALL/PLASTER WALL CONSTRUCTION, IT IS RECOMMENDED FOR FASTENERS TO BE ENGAGED INTO METAL/WOOD STUDS TO MAINTAIN MAXIMUM PULLOUT STRENGTH. IF DURING INSTALLATION YOU ENCOUNTER SPECIAL WALL CONDITIONS THAT DO NOT ALLOW FOR DIRECT ATTACHMENT TO THE STUDS PLEASE CONSULT THE LOCAL AUTHORITY HAVING JURISDICTION. 4. INSTALL OUTSIDE CORNERS FIRST. 5. INSTALL LONGEST RUN OF HANDRAIL FIRST. 6. SPLICES SHOULD NOT EXCEED 3" [76.2mm] DISTANCE FROM A FASTENER. 7. THE DISTANCE BETWEEN AN ACROVYN SPLICE JOINT AND AN SPLICE JOINT SHOULD BE STAGGERED 4" [101.6mm]. 8. MATERIAL MUST REACH 65 F MIN. TO 75 F MAX. 24 HOURS PRIOR TO INSTALLATION. THIS IS ESSENTIAL TO MINIMIZE EXPANSION AND CONTRACTION OF MATERIAL. 9. MAY REQUIRE USE OF FIRE PUTTY WHEN INSTALLED ON FIRE WALL WITH TOGGLE BOLTS. REFERENCE INSTRUCTIONS 24FIREPUTTY FOR FIRE PUTTY INSTALLATION. 12. THIS HANDRAIL REQUIRES A MINIMUM OF 2 FASTENERS PER MOUNTING BRACKET PER UNIT. THE MINIMUM END CAP-TO-END CAP CRASH RAIL LENGTH IS 13" [330.2mm] 13. FOR MORE INFORMATION ON SEE OUR WEBSITE AT

2 COMPONENTS & WALL FASTENERS ACROVYN HANDRAIL COVER (24U032xxx) ACROVYN CHAMELEON COVER (24U610xxx) FASTENER #1 #6 X 5/8" PHILLIPS FLAT HEAD SMS (90H231002) RC-10 CUSHION (24U952108) ACROVYN CRASH RAIL COVER (24U009xxx) ACROVYN CHAMELEON COVER (24U616xxx) MOUNTING BRACKET (24A365000) END PLATE (24F412000, LH SHOWN) (24F413000, RH) FASTENER #2 #10-24 X 1/2" HEX HEAD MACHINE SCREW (90H939002) FASTENER #3 #10 LOCK WASHER (90H370002) (24A354000) (24I083xxx, RH SHOWN) (24I082xxx, LH) CHAMELEON END CAP (24I634xxx, RH SHOWN) (24I610xxx, LH) CRASH RAIL END CAP (RIGHT-HAND SHOWN) (LEFT-HAND AVAILABLE) OUTSIDE CORNER PLATE (24F411000) FASTENER #4 #10 HEX NUT (90H368002) ACROVYN ACCENT REVEAL (24N021xxx) RETAINER SPLICE BAR (24I976000) FASTENER #5 #6 X 1/2" 18-8 S/S PIN-IN-TORX TAMPER-RESISTANT SHEET METAL SCREW (90H881002) ALIGNMENT PLUG (24I051000) HANDRAIL OUTSIDE CRASH RAIL OUTSIDE WALL CONDITION SPECIFIED FASTENER DRILL DIAMETERS WALL RETAINER C/S PART NUMBER STEEL STUD/GYPSUM WALL 1/4-20 X 5" ROUND HEAD BOLT WITH TOGGLE 1/4" LOCK WASHER 3/4" 9/32" 90H H CONCRETE/CONCRETE BLOCK #14 X 5" PHILLIPS RD HD ALL-PURPOSE SCREW 3/16" 9/32" 90H WOOD STUD/GYPSUM WALL #14 X 5" PHILLIPS RD HD ALL-PURPOSE SCREW 1/8" 9/32" 90H GA. STEEL STUD/GYPSUM WALL (OSHPD) 1/4-20 X 5" RD. HD. BOLT WITH FLAT WASHER 1/4" TOGGLER WING 3M MOLDABLE FIRE PUTTY 1/2" 9/32" 90H H H M012000

3 LAYOUT VIEW 3" [76.1mm] 1" [25.4mm] 1 7/16" [36.5mm] SEE "STEP 8" FOR ACROVN COVER CUTTING INSTRUCTIONS RETAINER LENGTH RC-10 CUSHION LENGTH LIGATURE RESISTANT MOUNTING BRACKET LENGTH EQUALS RETAINER LENGTH MINUS 2 3/4" [70.2mm] 1 5/16" [33.5mm] 3" [76.2mm] 4" [101.6mm] 1/2" [12.7mm] 1/2" [12.7mm] 3" [76.2mm] MAX. FIRST BRACKET LOCATION FASTENERS 32" O.C. MAX. [812.8mm] LAYOUT VIEW SPLICE 1 1/2" [38.1mm] 3" [75.9mm] 1 7/16" [36.5mm] FIELD DIMENSION (TYPICAL ALL WALLS) LIGATURE RESISTANT MOUNTING BRACKET LENGTH EQUALS RETAINER LENGTH MINUS 2 7/8" [73mm] 1" [25.4mm]

4 TYPICAL ACROVYN BUTT JOINT. STAGGER THE RETAINER AND ACROVYN JOINTS 4" [101.6mm] RH END PLATE WITH FASTENER #5 ALIGNMENT PLUG ACROVYN HANDRAIL COVER RETAINER SPLICE CONNECTOR HANDRAIL OUTSIDE CORNER MOUNT BRACKET CRASH RAIL OUTSIDE CORNER FASTENER #5 OUTSIDE CORNER PLATE 32" O.C. MAX. [812.8mm] SPECIFIED FASTENER LH LIGATURE RESISTANT END PLATE FASTENER #5 CRASH RAIL END CAP FASTENER #2, #3, #4 RC-10 CUSHION ACROVYN ACCENT REVEAL ACROVYN CRASH RAIL COVER

5 FASTENER #1 TYPICAL RH END PLATE WITH FASTENER #5 FASTENER #2, #3, #4 MOUNTING BRACKET HANDRAIL OUTSIDE OUTSIDE CORNER PLATE WITH FASTENER #5 CRASH RAIL OUTSIDE SPECIFIED FASTENER FASTENER #2, #3, #4 32" O.C. MAX. [812.8mm] CRASH RAIL END CAP NOTE: INSTALLATION OF LINEAL SHOULD BE DONE IN ACCORDANCE WITH THE FOLLOWING INSTRUCTIONS. 1. USING "LOCAL CODE" REQUIREMENTS, ESTABLISH HANDRAIL HEIGHT ABOVE FINISH FLOOR. DEDUCT 3 7/16" [86.8mm] AND SNAP A CHALK LINE AT THAT HEIGHT. THIS MARKS THE LOCATION OF THE HOLE FOR THE MOUNTING BRACKET FASTENER. 2. CUT THE CONTINUOUS AND THE MOUNTING BRACKET TO LENGTH USING THE REQUIRED DEDUCTIONS (REFERENCE LAYOUT VIEW). NOTE: IT IS RECOMMENDED THAT THE ACROVYN COVER AND BE CUT WITH AN TOOTH CARBIDE TIPPED SAW BLADE OR EQUIVALENT. 3. ATTACH THE END PLATES / OUTSIDE CORNER PLATES WITH (4) #6 X 1/2" TAMPER-RESISTANT SHEET METAL SCREWS ((8) FOR OUTSIDE CORNER PLATES). 4. ATTACH ALL END CAPS/OUTSIDE CORNERS: A. ATTACH HANDRAIL PORTION OF END CAP TO RETAINER: DRILL 5/32" DIAMETER CLEARANCE HOLES IN RETAINER 3/4" [19.1mm] FROM END OF RETAINER. INSERT THE END CAPS INTO THE RETAINER. DRILL 3/32" DIAMETER PILOT HOLES INTO THE END CAP. ATTACH END CAP TO RETAINER USING #6 x 5/8" PHILLIPS FLAT HEAD SHEET METAL SCREW. B. ATTACH CRASH RAIL PORTION OF END CAP TO THE RETAINER: USE END CAP AS TEMPLATE TO DRILL 7/32" PILOT HOLES IN RETAINER. ATTACH END CAP/OUTSIDE CORNERS BY SLIDING THE END CAP ONTO THE END OF THE AND SECURING INTO POSITION USING TWO (2) #10-24 X 1/2" HEX HEAD MACHINE SCREW WITH LOCK WASHER AND #10 HEX NUT AT EACH END CAP AND FOUR (4) AT EACH OUTSIDE CORNER. NOTE: TO AID IN LOCATING THE END CAPS CORRECTLY, CUT A 4" [101.6mm] SECTION OF COVER FROM SCRAP AND SNAP IT ON THE RETAINER. LOCATE THE CAP SO IT ALIGNS FLUSH WITH THE TOP AND BOTTOM OF THE COVER. 5. PRE-DRILL CLEARANCE HOLES IN THE AND MOUNTING BRACKETS 3" [76.2mm] FROM EACH END OF THE RETAINER AND 32" [812.8mm] O.C. AS REQUIRED AT THE V-GROOVE ALONG THE FRONT OF THE RETAINER AND MOUNTING BRACKET. FILE ALL ENDS OF RETAINER TO REMOVE BURRS AND SHARP EDGES AT HANDRAIL. 6. DRILL CLEARANCE HOLES IN WALL SURFACE FOR MOUNTING HARDWARE, USING THE RETAINER AND MOUNTING BRACKET AS A TEMPLATE. REFERENCE CHART ON PAGE 2 FOR CORRECT DRILL DIAMETERS. 7. INSTALL EACH SECTION OF ASSEMBLED RETAINER IN SUCCESSION USING THE MOUNTING BRACKET AND THE APPROPRIATE WALL FASTENERS.

6 TYPICAL CRASH RAIL END CAP MOUNTING BRACKET ACROVYN ACCENT REVEAL ACROVYN HANDRAIL COVER ACROVYN CRASH RAIL COVER RC-10 CUSHION 8. CUT RC-10 CUSHION TO LENGTH NOTING REQUIRED DEDUCTIONS (SEE LAYOUT VIEW) AND INSTALL ONTO. 9. CUT ACCENT REVEAL TO LENGTH AND INSERT INTO SLOT PROVIDED IN THE TOP SECTION OF THE. NOTE: SEE PAGE 8 FOR CHAMELEON REVEAL INSTALLATION. 10. CUT ACROVYN HANDRAIL COVER AND ACROVYN CRASH RAIL TO LENGTH. THE COVER LENGTH IS DETERMINED BY MEASURING THE DISTANCE BETWEEN THE INSTALLED END CAPS AND/OR OUTSIDE CORNER ASSEMBLIES. NOTE: IT IS RECOMMENDED THAT THE ACROVYN COVERS BE CUT SLIGHTLY LONGER (1/32" UP TO 5'-0", 1/16" OVER 5'-0") THAN THE MEASURED DISTANCE. THIS ADDITIONAL LENGTH WILL PROVIDE FOR A TIGHTER COVER-TO-END CAP FIT. 11. STARTING AT ONE END, SNAP THE HANDRAIL COVER ONTO THE RETAINER ALONG THE LENGTH OF THE HANDRAIL. 12. COMPLETE INSTALLATION BY INSTALLING THE ACROVYN COVER ONTO THE LOWER PORTION OF THE RETAINER. NOTE: MANUFACTURER RECOMMENDS ALL PRINTED "PRODUCT IDENTIFICATION" ON THE REAR OF THE ACROVYN PROFILE SHALL BE ORIENTED IN THE SAME DIRECTION DURING INSTALLATION TO ENSURE PROPER ALIGNMENT AT SPLICE BUTT JOINTS.

7 OUTSIDE HANDRAIL OUTSIDE FASTENER #1 FASTENER #3 & #4 CRASH RAIL OUTSIDE FASTENER #2 FASTENER #1 HANDRAIL OUTSIDE FASTENER #3 & #4 FASTENER #2 CRASH RAIL OUTSIDE OUTSIDE CORNER INSTALLATION 1. ATTACH ALL OUTSIDE CORNERS: A. ATTACH HANDRAIL PORTION OF OUTSIDE CORNER TO RETAINER: DRILL 5/32" DIAMETER CLEARANCE HOLES IN RETAINER 3/4" [19.1mm] FROM END OF RETAINER. INSERT THE OUTSIDE CORNERS INTO THE RETAINER. DRILL 3/32" DIAMETER PILOT HOLES INTO THE END CAP. ATTACH OUTSIDE CORNER TO RETAINER USING #6 x 5/8" PHILLIPS FLAT HEAD SHEET METAL SCREW. B. ATTACH CRASH RAIL PORTION OF OUTSIDE CORNER TO THE RETAINER: USE OUTSIDE CORNER AS TEMPLATE TO DRILL 7/32" PILOT HOLES IN RETAINER. ATTACH OUTSIDE CORNERS BY SLIDING THE CORNER ONTO THE END OF THE AND SECURING INTO POSITION USING FOUR (4) #10-24 X 1/2" HEX HEAD MACHINE SCREW WITH LOCK WASHER AND #10 HEX NUT AT EACH OUTSIDE CORNER. NOTE: TO AID IN LOCATING THE OUTSIDE CORNERS CORRECTLY, CUT A 4" [101.6mm] SECTION OF COVER FROM SCRAP AND SNAP IT ON THE RETAINER. LOCATE THE CORNER SO IT ALIGNS FLUSH WITH THE TOP AND BOTTOM OF THE COVER. NOTE: SOLID PORTION OF OUTSIDE CORNER FLANGE MOUNTS TO THE BACK OF THE RETAINER WHILE THE SPLIT FLANGE MOUNTS TO THE INSIDE OF THE RETAINER. SEE ILLUSTRATION ABOVE.

8 CHAMELEON REVEAL MOUNTING BRACKET ACROVYN HANDRAIL COVER 32" O.C. MAX. [812.8mm] FASTENER #5, #6, #7 CRASH RAIL END CAP CHAMELEON END CAP REVEAL RC-10 CUSHION ACROVYN ACCENT REVEAL ACROVYN CRASH RAIL COVER ACROVYN CHAMELEON ACCENT REVEAL CHAMELEON REVEAL INSTALLATION (3) #6 x 3/8" PH PAN HD SMS END CAPS 1. LOOSEN THE #6 x 3/8" PHILLIPS PAN HEAD SHEET METAL SCREWS THAT HOLD THE END CAP REVEAL ADAPTER TO THE END CAP. 2. SLIDE THE CHAMELEON END CAP REVEAL OVER THE INSTALLED END CAP ADAPTER. BE SURE TO PLACE THE LONG LEG OF THE CHAMELEON REVEAL AT THE TOP. END CAP REVEAL ADAPTER CHAMELEON END CAP REVEAL 3. TIGHTEN THE (3) THREE #6 x 3/8" PHILLIPS PAN HEAD SHEET METAL SCREWS HANDRAIL 1. CUT CHAMELEON ACCENT REVEAL TO LENGTH AND INSERT INTO SLOT PROVIDED IN THE TOP SECTION OF THE ON TOP OF PREVIOUSLY INSTALLED STANDARD REVEAL. CRASH RAIL END CAP Muncy, Pennsylvania (800) Fax (570) Mississauga Ontario (888) Fax (905) This document is the property of Construction Specialties, Inc. and contains CONFIDENTIAL PROPRIETARY INFORMATION that is not to be disclosed to third parties and is not to be used without approval in writing from Construction Specialties, Inc.