STOP! Call Us First! DO NOT RETURN TO STORE.

Transcription

1 16529 STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number: or Our staff is ready to provide assistance April through October M-F 8:00 AM to 4:30 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST

2 (This page intentionally left blank.)

3 /07/2018 A Backyard Products Company NORTHPORT GABLE 10' x 10' (305 x 305 cm) ACTUAL FLOOR SIZE IS 120 x 116-5/8" (304,8 x 296,2 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO NING ASSEMBLY. BEFORE YOU BUILDING RESTRICTIONS AND APPROVALS Be sure to check with local building department and homeowners association for specific restrictions and/or requirements before building.. ENGINEERED DRAWINGS Contact our Customer Service Team if engineered drawings are needed to pull local permits. SURFACE PREPARATION To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are listed on page 7. CHECK ALL PARTS Inventory all parts listed on pages 4-6. Contact our Customer Service Team if any parts are missing or damaged. ADDITIONAL MATERIALS You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities. - CUSTOMER SERVICE - Call: customerservice@heartlandind.com

4 TOOLS Phillips Screwdriver Drill / Driver 1/8" Drill Bit 1/4" Drill Bit 5/16" Drill Bit 1/2" Drill Bit #2 Philips Drive Bit Hammer Level Pencil Tape Measure Square or Required Utility Knife Shingle Blades Caulk Gun Paint Tools Safety Glasses Hand Saw Ladder Tool Belt/ Nail Pouch Gloves Optional Tin Snips (for drip edge) Chalk Line Nail Gun gun nails Safety! Always use approved safety glasses during assembly. HELPFUL REMINDER SYMBOLS Look for these symbols for helpful reminders throughout this manual. = Assistance Required; two or more people. = Mark part with pencil. = Ensure squareness. = Beginning of steps for assembly or installation. = Important required step or operation. = You have fi nished the assembly or installation. = Helpful assembly hint. = Level ORIENT LUMBER AND TRIM FOR BEST APPEARANCE Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side. Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way negatively affect the strength or integrity of our product. (See Fig. A, B, C.) A B C 2

5 This shed does not include any floor or leveling materials. ADDITIONAL MATERIALS FOUNDATION OR FLOOR MATERIALS See the FLOOR LEVELING section on page 7 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. WOOD FLOOR FRAME MATERIAL REQUIRED: Use only wood treated for ground contact and fasteners approved for use with treated wood. 1 2 x 4 x 120" (5,1 x 10,2 x 304,8 cm) x36 Hot Dipped Galvanized Box-Type Nails. FLOOR PANELS NOTE: Use a minimum of 5/8" (1,6 cm) Oriented Strand Board (OSB) x4 REINFORCED WOOD FLOOR FRAME (OPTIONAL) IMPORTANT! This floor has been designed for general use. Depending on your specific use you may want to construct a heavy duty floor frame by adding additional floor joists (shown below as shaded). Below is a list of additional materials (not included): 5/8" x 48" x96" (1,6 x 121,9 x 243,8 cm) Cut 1 panel to: 24 x 96" and 20-5/8 x 96". Cut 1 panel to: 20-5/8 x 24". 2 x 4 x 10' (5 x 10 x 304,8 cm) Treated Lumber Cut to (3) 2 x 4 x 117" (5 x 10 x 297,2 cm) 1 lb. of Hot Dipped Galvanized Box-Type Nails. x8 ea. Hot Dipped Galvanized Nails Standard 16" (40,7 cm) spacing COMPLETING YOUR SHED You will need these additional materials: Optional 12" (30,5 cm) spacing 3-TAB SHINGLES... 6 Bundles PAINT FOR SIDING... 2 Gallons Use 100% acrylic latex exterior paint. (2) coats recommended. CAULK... 3 Tubes Use acrylic latex exterior caulk that is paintable. 1" GALVANIZED ROOFING NAILS... 2 Lbs For shingles. PAINT FOR TRIM...2 Quarts Use 100% acrylic latex exterior paint. WOOD GLUE... Exterior Rated OPTIONAL MATERIALS DRIP EDGE Feet #15 ROOFING FELT To cover 134 Sq. Ft. of roof area. 1" GALVANIZED ROOFING NAILS...1/4 Lb For roofing felt. REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER S INSTRUCTIONS FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT. 3

6 WALLS RAFTERS TRIM DOORS Part identification letters are stamped on some parts. RS RS Check these locations for part stamp. PARTS IDENTIFICATION AND SIZES PARTS LIST INVENTORY YOUR PARTS before you begin. We suggest sorting parts by the category they are listed in. x4 x3 x x8 x4 x4 x4 x4 GAA BJC CPB RL KHA STL AM YFA TM TJ TP HJ ECN CLA EY YR ZJ ECA AH GPL GPR OO 1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) Gauge Block for 3/4" (1,9 cm) measurement 2 x 4 x 17-3/16" (5,1 x 10,2 x 43,7 cm) 2 x 4 x 20-5/8" (5,1 x 10,2 x 52,4 cm) 2 x 4 x 24" (5,1 x 10,2 x 61 cm) 2 x 4 x 24-1/2" (5,1 x 10,2 x 62,2 cm) 6 x 24" (15,2 x 61 cm) GUSSET 3/8 x 3-1/4 x 5-7/8" (1 x 8,3 x 14,9 cm) SHIM 2 x 4 x 4-7/8" (5,1 x 10,2 x 12,4 cm) 19/32 x 2-1/2 x 9" (1,5 x 6,3 x 22,8 cm) 2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm) 4 7/16 x 3 x 67" (5,1 x 7,6 x 1,1 cm) 2 x 4 x 67" (5,1 x 10,3 x 170,2 cm) 19/32 x 2-1/2 x 32-3/4" (1,5 x 6,3 x 83,1 cm) 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) 1 x 3 x 72" (1,6 x 7,6 x 182,9 cm) 3/8 x 5-7/8 x 45-3/8"" (1 x 14,9 x 115,3 cm) 19/32 x 3 x 26-5/8" (1,5 x 7,6 x 67,6 cm) WOOD SIZE CONVERSION CHART Nominal Board Size Actual Size 2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm) 3/8 x 5-7/8 x 72-3/4" (1 x 14,9 x 184,8 cm) 19/32 x 3 x 72" (1,5 x 7,6 x 183 cm) 3/8 x 4-3/4 x 45-3/8" (1 x 12,1 x 115,3 cm) 3/8 x 7-7/8 x 73-5/16" (1 x 20 x 186,2 cm) 3/8 x 1-3/4 x 73-7/8" (1,0 x 4,4 x 187,6 cm) 3/8 x 1-3/4 x 74-1/2" (1,0 x 4,4 x 189,2 cm) 2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm) 19/32 x 2-1/2 x 51" (1,5 x 7,6 x 67,6 cm) 19/32 x 2-1/2 x 51" (1,5 x 7,6 x 67,6 cm) 1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,3 cm) 2" x 4"...1-1/2" x 3-1/2" (3,8 x 8,9 cm) 1" x 4"...3/4" x 3-1/2" (1,9 x 8,9 cm) 2" x 3"...1-1/2" x 2-1/2" (3,8 x 6,3 cm) 1" x 3"...3/4" x 2-1/2" (3,8 x 6,3 cm) 3/8 x 4-3/4 x 75-7/8" (1 x 12,1 x 197,2 cm) 3/8 x 4-3/4 x 75-7/8" (1 x 12,1 x 197,2 cm) 3/8 x 4-3/4 x 80-5/8" (1 x 12,1 x 204,8 cm) 3/4" (1,9 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235,3 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

7 SHELF - LOFT ROOF PANELS x6 x3 x3 AE RL JS KP TP Roof panels are 7/16" (1,1 cm) thick. 7/16 x 8-5/8 x 27-1/4" (1,1 x 21,9 x 69,2 cm) 7/16 x 20-5/8 x 27-1/4" (1,1 x 52,4 x 69,2 cm) 7/16 x 48 x 96" (1,1 x 121,9 x 243,8 cm) 2 x 3 0-1/8" (5,1 x 7,6 x 25,7 cm) PARTS LIST continued... 2 x 4 x 24" (5,1 x 10,2 x 61 cm) 1 x 4 x 23-7/8" (2,5 x 10,2 x 60,6 cm) PANEL PARTS LIST 7/16 x 8-5/8 x 48" (1,1 x 21,9 x 121,9 cm) x4 7/16 x 27-1/4 x 48" (1,1 x 69,2 x 121,9 cm) NOTE: Panel parts are not stamped. Wall panels panels are 3/8" (1,1 cm) thick. 7/16 x 20-5/8 x 48" (1,1 x 52,4 x 121,9 cm) SHELF AND LOFT WALL PANEL & DOORS PARTS LIST x6 1 x 4 x 96" (2,5 x 10,2 x 243,8 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 3/8 x 8 x 12-1/2" (1 x 20,3 x 31,8 cm) 7/16 x 11-7/8 x 23-7/8" (1,1 x 30,2 x 60,6 cm) 7/16 x 11-7/8 x 96" (1,1 x 30,2 x 243,8 cm) 20-1/2" x 96" (52,1 x 243,8cm) 3/8 x 11-7/8 x 76" (1 x 30,2 x 193 cm) 3/8 x 20-5/8 x 76" (1 x 52,4 x 193 cm) 3/8 x 23-7/8 x 76" (1 x 60,6 x 193 cm) 21-1/2 x 36" (54,6 x 121,9 cm) 21-1/2 x 36" (54,6 x 121,9 cm) NOTE: Panel parts are not stamped. x6 3/8 x 48 x 76" (1 x 121,9 x 193 cm) LEFT DOOR RIGHT DOOR 5 3/8 x 48 x 76" (1 x 121,9 x 193 cm) 3/8 x 48 x 76" (1 x 121,9 x 193 cm)

8 FASTENERS & HARDWARE NAIL BOXES x4 BOXES x6 BOXES FASTENER/HARDWARE BAG x80 1-1/2" (3,8 cm) 6 1-1/4" (3,2 cm) /2" (1,3 cm) x99 6 2" (5,0 cm) 2 1-5/8" (4,1 cm) (NOT ACTUAL SIZE) x76 3/4" (1,9 cm) 3/8" x5-1/2" (1 cm x 14 cm) Hex Bolt x4 3/8" (1 cm) Flat Washer 3/8" (1 cm) Lock Nut VENT/ DOOR HARDWARE/ WINDOW x4 Handle (locking) with Screws Transom Window 2 3/4" (1,9 cm) 1-1/4 64" Metal Threshold 3/4" (1,9 cm) 1 Bagged seperately / special coating Wall Vent 86" 6

9 FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS 3" Screws angled into 4x4. (2) at each point frame and 4x4 touch. 12" (30,5 cm) DOOR MATERIAL REQUIRED x3 4 x 4 x 10' (8,9 x 8,9 x 305 cm) Treated Lumber 12" (30,5 cm) Fasteners for Frame to 4x4. (3" Screws shown as one option.) Minimum (54) 3" screws / exterior grade. Measurements to centers of 4x4's. Use only wood treated for ground contact and fasteners approved for use with treated wood. Always support frame seams. 12" Maximum between leveling material locations. 48" Shingle Level 4x4 Runner 12" Shingle Gravel 2" Block Gravel LEVELING METHODS 4" Block 2x4 Treated Lumber 8" Block Level under 4x4 runners only. Locate leveling material 12" from ends of runners and no more than 48" apart. Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use shingles in direct contact with ground. For best results and aiding in water drainage use gravel under each concrete block. LEVELING MATERIALS Gravel Solid Masonry Blocks in 1", 2", 4" or 8" thickness 2x4 Treated Lumber Asphalt Shingles Leveling higher than 16" not recommended. CONCRETE If you are building your shed on a concrete foundation see the following page. 7 Do not exceed 16".

10 CONCRETE FOUNDATION If you choose to install your kit on a concrete slab, refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. C B 3-1/2" (8,9 cm) 4" (10,2 cm) A DOOR Building Size 10'x 10' (305 x 305 cm) Actual Size A B C 10'x 9'-8-5/8" (305 x 296 cm) 120" (305 cm) 109-5/8" (278 cm) 116-5/8" (296,2 cm) Requires: x4 2 x 4 0' (5 x 10 x 305 cm) MUST be treated lumber. Caulk Allow new concrete slabs to cure for at least seven (7) days. A treated 2 x 4 (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete. Hint: purchase full length treated lumber. Use a high quality exterior grade caulk beneath all sill plates. Fasten 2 x 4 (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fasteners not included). Check local code for concrete foundation requirements. NOTES 8

11 1 2 x 4 x 117" (5,1 x 10,2 x 297,2 cm) FLOOR FRAME x36 1 Orient parts as shown on fl at surface. Measure and mark. Use two 3" nails at each mark. HINT: For easier nailing stand on frame. You have fi nished your fl oor frame /8" (296,2 cm) 106" (269,2 cm) 96" (243,8cm) 80" (203,2 cm) 64" (162,6 cm) 48" (121,9 cm) 32" (81,3 cm) 16" (40,6 cm) 10-5/8" (27 cm) Center on marks DOOR 120" (304,8 cm) 117" (297,2 cm) 9

12 LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. 1 See page 7 for the preferred floor leveling method. 2 Use level and check the frame is level before applying fl oor panels. 3 Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square. The diagonal measurement will be approximately 167-5/16" (425 cm). 4 When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one fastener at ends of each runner making sure the frame remains square (Fig. A). First, secure at ends with one fastener. Fig. A 167-5/16" (425 cm) 167-5/16" (425 cm) DOOR 120" (304,8 cm) 116-5/8" (296,2 cm) Second, secure at ends with one fastener. Once the floor frame is level and square fasten the frame to the 4x4 runners at each point the frame contacts the 4x4 runners. 10

13 FLOOR PANELS 5/8 x 48 x 96" (1,6 x 121,9 x 243,8 cm) 3/4" GAUGE BLOCK x53 Install panels with rough side up (painted grid lines). 1 Attach the 48 x 96" panel with the outside edges flush to the outside of the floor frame. Use GAA gauge block for the ¾ measurement. Attach the panel using 2" nails, 6" apart on edges and 12" apart inside panel. Use a chalk line or use pre-painted grid lines to nail into joists. 6" (15,2 cm) 3/4" GAUGE BLOCK For squareness maintain 3/4" measurement along panel edge. 3/4" (1,9 cm) 12" (30,5 cm) 116-5/8" (296,2 cm) Grid lines up 5/8 x 48 x 96" (1,6 x 122 x 243,8 cm) 120" (304,8 cm) DOOR 11

14 FLOOR PANELS 3/4" GAUGE BLOCK 35 5/8 x 48 x 96" (1,6 x 122 x 243,8 cm) 5/8 x 23-7/8 x 96" 5/8 x 20-5/8 x 96" (1,6 x 60,6 x 243,8 cm) (1,6 x 52,4 x 243,8 cm) 5/8 x 20-5/8 x 23-7/8" (1,6 x 52,4 x 60,6 cm) 2 Continue installing the remaining panels in the following order: x 96" /8 x 96" /8 x 96" /8 x 23-7/8" Maintain 3/4" measurement along edge of panel using the 3/4 Gauge Block. Secure panels using 2" nails 6" apart on edges and 12" apart inside panel. All panels should be fl ush. 5/8 x 20-5/8 x 23-7/8" (1,6 x52,4 x 243,8 cm) 5/8 x 20-5/8 x 96" (1,6 x52,4 x 243,8 cm) 6" (15,2 cm) 3/4" GAUGE BLOCK 3/4" GAUGE BLOCK 12" (30,5 cm) Grid lines up 5/8 x 48 x 96" (1,6 x 122 x 243,8 cm) 5/8 x 23-7/8 x 96" (1,6 x 60,6 x 243,8 cm) You have fi nished attaching your fl oor panels. 12 DOOR

15 IMPORTANT! Check that the floor frame is level after installing floor panels. Re-level if needed. The floor should be used as a stable work surface for wall construction. HINT: Organize your assembly procedure during the build process to avoid over-handling of the walls. LEFT WALL BACK WALL FRONT WALL RIGHT WALL 13

16 CLA 2 x 4 x 4-7/8" (5,1 x 10,2 x 12,4 cm) RAFTER ASSEMBLY x4 You will build a rafter jig using the floor and two CLA parts as shown. 1 Secure one CLA flush to the floor deck using two 3" screws. Measure over 120-3/4" and install a second CLA. Secure using two 3" screws. Fig. A 120" (304,8 cm) Floor Width (2) Screws in each CLA There will be an overhang on this end. 3/4" (1,9 cm) CLA 120-3/4" (306,7 cm) You have finished rafter jig. Proceed to assemble your rafters. 14

17 x8 GUSSET 6 x 24" (15,2 x 61 cm) RAFTER ASSEMBLY x8 1-5/8" (4,1 cm) x88 x8 ECN 2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm) 1 Place two rafters ECN into the jig as shown. Keep ECN firm against outside CLA's as shown (Fig.A). Rafters should touch at tips (Fig. A). Apply glue to rafters where gusset will attach (Fig. B). Place gusset onto ECN holding a 1/4" gap from edge (Fig. C). Secure gusset using one 1-5/8" screw into each rafter. HINT: These screws will help hold the measurements when you nail on gussets. Use (10) 2" nails to finish securing the gusset to the rafters to pattern shown in Fig. C. Fig. A 1/4" (1,9 cm) GAP 1-5/8" (4,1 cm) Screw 1/4" (1,9 cm) GAP ECN Keep rafters firmly against CLA at both ends when securing gusset. 2 Flip rafters over and attach a second gusset using glue and (12) 2" nails. No need to use jig for 2nd gusset. 3 Repeat STEPS 1-2 to assemble three more rafters. Glue where gusset installs Fig. B ECN 120-3/4" (306,7 cm) 1/4" (1,9 cm) GAP 1/4" (1,9 cm) GAP Fig. C 15

18 GUSSET 6 x 24" (15,2 x 61 cm) RAFTER ASSEMBLY x4 1-5/8" (4,1 cm) 0 x4 ECN 2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm) Gable-end rafter assemblies only have one gusset. 4 Repeat steps to assemble two more rafters with only one gusset. Fig. A 1/4" (1,9 cm) GAP 1-5/8" (4,1 cm) Screw 1/4" (1,9 cm) GAP ECN Keep rafters firmly against CLA at both ends when securing gusset. Glue where gusset installs Fig. B ECN 120-3/4" (306,7 cm) 1/4" (1,9 cm) GAP 1/4" (1,9 cm) GAP Fig. C 5 Remove CLA's from floor. You have fi nished assembling your rafters. 16

19 AM 2 x 4 x 67" (5,1 x 10,2 x 170,2 cm) OSB 7/16 x 3 x 67" (1,1 x 7,6 x 170,2 cm) FRONT WALL (Door Header) Build Door Header with OSB in the middle, use 3 Nails. Glue both sides of OSB. 2 Flip header assembly over and nail on the other side. ASSEMBLED END VIEW AM Glue both sides. AM OSB You have assembled your door header. 17

20 x3 KHA 2 x 4 x 24-1/2" (5,1 x 10,2 x 62,2 cm) YFA 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) x6 TM 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) FRONT WALL x54 STL 2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm) Pre Assembled Header 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. HINT: For easier nailing stand on frame. 44-1/2" (113 cm) 113" (287 cm) 104-1/2" (265,4 cm) 90-3/4" (230,5 cm) 68-1/2" (174 cm) 22-1/4" STL YFA (56,5 cm) 8-1/2" (21,6 cm) Pre Assembled Header 1-1/2" (3,8 cm) Nails Install Header in this position 68-1/2" (174 cm) 72" (182,9 cm) TM x6 YFA YFA KHA KHA 8-1/2" (21,6 cm) 24-1/2" (62,2 cm) 24-1/2" (62,2 cm) 8-1/2" (21,6 cm) 18

21 FRONT WALL 3/4" GAUGE BLOCK 48 x 76" (121,9 x 193 cm) LEFT + RIGHT x80 Install all panels with primed side up. 2 Place left and right 48" x 76" panels onto wall frame flush to top as shown. Secure panels with 2" nails 6" apart. For squareness maintain flush along panel edges. 6" (15,2 cm) 3/4" GAUGE BLOCK 3/4" GAUGE BLOCK Maintain Maintain 19

22 FRONT WALL x /8 x 76" (30,2 x 193 cm) HJ Temporary Support 1 x 3 x 72" (1,6 x 7,6 x 182,9 cm) 3 4 Place 11-7/8" x 76" panels onto wall frame fl ush to top of frame as shown. Secure panel using 2" nails 6" apart. Attach temporary support HJ to frame as shown using 3" screws. 11-7/8" (30,2 cm) 11-7/8" (30,2 cm) Primed side up Primed side up 6" (15,2 cm) Maintain Maintain 64" (162,6 cm) Temporary Support HJ Screws You have fi nished building your front wall. 20

23 x6 TM 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) YFA 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) BACK WALL 8 STL 2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm) 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. HINT: For easier nailing stand on frame. 68-1/2" (174 cm) 113" (287 cm) 92-1/2" (235 cm) 68-1/2" (174 cm) 44-1/2" (113 cm) 20-1/2" (52,1 cm) YFA STL Nails Nails TOENAILING 72" (182,9 cm) 1-1/2" (3,8 cm) TM x6 STL YFA 44-1/2" (113 cm) 68-1/2" (174 cm) 21

24 BACK WALL 48 x 76" (121,9 x 193 cm) 23-7/8 x 76" (60,6 x 193 cm) 3/4" GAUGE BLOCK 22 2 Install back wall panels with primed side up as shown. Secure panels to frame using 2" nails 6" apart along edges and 12" apart on inside of panel. 3/4" (1,9 cm) HERE For squareness maintain flush and 3/4" measurement along panel edges. 6" (15,2 cm) 12" (30,5 cm) 3/4" GAUGE BLOCK 48" (122 cm) 23-7/8" (60,6 cm) 48" (122 cm) Carefully fl ip the back wall over. You have fi nished building your back wall. 22

25 x6 RL 2 x 4 x 24" (5,1 x 10,2 x 61 cm) TM 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) TJ 2 x 4 x 92-5/8" (5,1 x 10,2 x 235,3 cm) LEFT WALL CPB 2 x 4 x 20-5/8" (5,1 x 10,2 x 52,4 cm) 8 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. HINT: For easier nailing stand on frame. 20-5/8" (52,4 cm) 44-1/2" (113 cm) 68-1/2" (174 cm) 116-5/8" 92-5/8" (296,2 cm) 24" (235,3 cm) (61 cm) RL TJ Nails TOENAILING TM x6 72" (182,9 cm) DOOR 1-1/2" (3,8 cm) CPB TP 20-5/8" (52,4 cm) 96" (243,8 cm) 23

26 LEFT WALL 20-5/8 x 76" (52,4 x 193 cm) x 76" (121,9 x 193 cm) 3/4" GAUGE BLOCK 2 Install left wall panels with primed side up as shown. Secure panels to frame using 2" nails 6" apart along edges and 12" apart on inside of panel. HERE For squareness maintain flush and 3/4" measurement along panel edges. 3/4" (1,9 cm) 12" (30,5 cm) 6" (15,2 cm) 3/4" GAUGE BLOCK Maintain 20-5/8" (52,4 cm) 48" (122 cm) 48" (122 cm) Carefully fl ip the left wall over. You have fi nished building your left wall. DOOR 24

27 x6 RL 2 x 4 x 24" (5,1 x 10,2 x 61 cm) TM 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) TJ 2 x 4 x 92-5/8" (5,1 x 10,2 x 235,3 cm) RIGHT WALL CPB 2 x 4 x 20-5/8" (5,1 x 10,2 x 52,4 cm) 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. 8 HINT: For easier nailing stand on frame. 24" (61 cm) RL 116-5/8" (296,2 cm) 92-5/8" (235,3 cm) 68-1/2" (174 cm) 44-1/2" (113 cm) 20-5/8" (52,4 cm) Nails TJ TOENAILING DOOR 72" (182,9 cm) TM x6 1-1/2" (3,8 cm) TP CPB 96" (243,8 cm) 20-5/8" (52,4 cm) 25

28 RIGHT WALL 20-5/8 x 76" (52,4 x 193 cm) x 76" (121,9 x 193 cm) 3/4" GAUGE BLOCK 2 Install right wall panels with primed side up as shown. Secure panels to frame using 2" nails 6" apart along edges and 12" apart on inside of panel. For squareness maintain flush and 3/4" measurement along panel edges. HERE 3/4" (1,9 cm) 12" (30,5 cm) 6" (15,2 cm) 3/4" GAUGE BLOCK Maintain 48" (122 cm) 48" (122 cm) 20-5/8" (52,4 cm) Carefully fl ip the right wall over. You have fi nished building your right wall. DOOR 26

29 OO 1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,3 cm) BACK WALL INSTALLATION 0 x30 1 Center back wall assembly on the 120" (304,8 cm) fl oor dimension. Use OO as a temporary brace. Secure with two 3" screws. OO 120" (304,8 cm) DOOR Screws 2 First, nail lower edge of panel to fl oor frame using 2" nails 6" apart. Angle nail to hit fl oor frame (Fig. A). Secure back wall bottom plates to fl oor using 3" nails (Fig. A). Nails Nail 2" nails first. Fig. A Nails 3" Nails into bottom plate 6" (15,2 cm) DOOR You have fi nished installing your back wall. 27

30 LEFT WALL INSTALLATION 3 1 Secure back wall to left wall using one 2" screw into left wall top and bottom plates (Fig. A). ENSURE TOP OF WALL FRAMES ARE FLUSH. 2" (3,8 cm) Screw 2" (5,1 cm) Screw Fig. A 2" (5,1 cm) Screw 6" (15,2 cm) Nails Nail Fig. B Angle nail to hit floor frame. 2 Nail lower edge of left wall panels to fl oor using 2" nails 6" apart. Angle nail to hit fl oor frame (Fig. B). ENSURE LEFT AND BACK WALL PANELS ARE FLUSH BEFORE SECURING. 28

31 LEFT WALL INSTALLATION 2 1-1/2" (3,8 cm) 0 3 Nail back wall panel to left wall stud using 1-1/2" nails 6" apart (Fig. C). Secure back wall top frame 2 x 4 using 3" screw toe-screwed into left wall frame at an angle as shown (Fig. D). Secure left wall to fl oor using 3" nails (Fig. C). 1-1/2" (3,8 cm) Nails Fig. D Screw 6" (15,2 cm) Fig. C Nails You have fi nished installing your left wall. 29

32 RIGHT WALL INSTALLATION 3 1 Secure back wall to right wall using one 2" screw into right wall top and bottom plates (Fig. A). ENSURE TOP AND BOTTOM PLATES ARE FLUSH. Screw Fig. A 2" (5,1 cm) Screw 2" (5,1 cm) Screw 6" (15,2 cm) Nails Angle nail to hit floor frame. Fig. B 2 Nail panels to fl oor using 2" nails 6" apart. Angle nail to hit fl oor frame (Fig. B). ENSURE RIGHT AND BACK WALL PANEL ARE FLUSH BEFORE SECURING. 30

33 RIGHT WALL INSTALLATION 2 1-1/2" (3,8 cm) 0 3 Nail back wall panel to right wall stud using 1-1/2" nails 6" apart (Fig. C). Secure right and back wall top plates using 3" screw toe-screwed at an angle as shown in (Fig. D). Secure bottom plate to fl oor using 3" nails (Fig. C). Screw Fig. D 6" (15,2 cm) Fig. C 1-1/2" (3,8 cm) Nails Nails You have fi nished installing your right wall. 31

34 FRONT WALL INSTALLATION 4 x4 1-1/2" (3,8 cm) 1 Center front wall assembly on the fl oor. Panel DOOR 2 Secure front wall using one 2" screw into left and right wall top and bottom plates (Fig. A). Screw Fig. A Fig. A 1-1/2" (3,8 cm) Nails 6" (15,2 cm) Screw 2" (7,6 cm) Screw 3 Nail front wall panel to left and right wall studs using 1-1/2" nails 6" apart. 32 2" (7,6 cm) Screw

35 4 x6 FRONT WALL INSTALLATION 4 Nail lower edge of panels to fl oor frame using 2" nails 6" apart. Angle nail to hit fl oor frame (Fig. B). Secure front wall bottom plates to fl oor using 3" nails (Fig. B). Secure front wall top plate using one 3" screw toe-screwed into left and right top plates at an angle, as shown in (Fig. C). Screw Fig. C Nail 2" nails first. Nails Nails Fig. B 6" (15,2 cm) You have fi nished installing your front wall. 33

36 RAFTERS x4 0 Preassembled Truss (2 gusset) Preassembled Truss (1 gusset) 1 Secure rafters to top plate with two 3" screws above notch, as shown in Fig. A, B. Note the One Gusset Rafters at each end. 24-3/8" (61,9) cm) 24" (61 cm) 24" (61 cm) 24" (61 cm) 21" (53,3) cm) Fig. A Align over studs. to outside of panel Only 1 Screw End Rafters Fig. B (3) Screws Only 1 Screw End Rafters Fig. C Tight to side wall to outside of panel You have fi nished attaching your rafters. 34

37 DOORS OO 1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,3 cm) GAA 1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) x4 1-1/4" (3,2 cm) Left Door Assembled Right Door Assembled 1 Orient parts as shown on flat surface. 3/8" offset is to top. Look for red (right) and green (left) on hinge board. Attach temporary supports OO and GAA as shown. Tighten securely. OFFSET 3/8" (1 cm) GREEN 3/8" (1 cm) RED 3/8" OFFSET (1 cm) (4) Screws OO 1-1/4" (3 cm) Screws GAA 3/8" (1 cm) Bottom edges 35

38 OO 1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,3 cm) DOORS 3 1 Attach temporary support OO as a ledger board flush under wall panels for doors to rest on, using three 3" screws (Fig. A). Fig. A OO 2 Center doors in door opening (Fig. B). Screw hinge boards into wall supports and floor using (10) 3" screws as shown. Screw against wall panels OO Fig. B Screws into door trim. 3 Remove temporary supports and check doors open properly. 36

39 DOORS 3/4" (1,9 cm) 1 x5 GPL Bagged seperately / special coating 19/32 x 2-1/2 x 51" (1,5 x 6,3 x 129,5 cm) GPR 64" Metal Threshold 19/32 x 2-1/2 x 51" (1,5 x 6,3 x 129,5 cm) ZJ x4 AH 19/32 x 3 x 72" (1,5 x 7,6 x 183 cm) 19/32 x 3 x 26-5/8" (1,5 x 7,6 x 67,6 cm) x68 3/4" (1,9 cm) 1 Reinforce the door and install only upper horizontal door rails AH using 3/4" screws through door panel into trim (Fig. A, B). 2 Attach GPL and GPR first, then lower horizontal door rails with 3/4" screws. 3 Center trim ZJ over doors and secure using fi ve 2" fi nish nails. 3/4" (1,9 cm) Screws from behind. 4 Install metal threshold (Fig. C). ZJ Door Panel Fig. A Finish Nails x5 CENTER 9" (22,9 cm) Door Trim GPL AH Fig. B 9" (22,9 cm) GPR (11) Special Coating Screws Fig. C You have fi nished securing your door and trim. 37

40 DOOR STIFFENERS OO 1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,3 cm) 4 1 Center OO s vertically on the left and right doors as shown (Fig. A,B). Secure using (7) 2" screws through outside trim into OO (Fig. B). Fig. B OO Center OO in door opening. Fig. A IT IS IMPORTANT TO HOLD THESE DIMENSIONS OFFSET 3/4" (2,5 cm) 3/4" (1,9 cm) OVERLAP Screws 2" (5,1 cm) 2" (5,1 cm) Screws 4 11" (27,9 cm) Approximately You have installed your door stiffeners. 38

41 DOOR HARDWARE 1/2" (13 mm) Drill Bit x4 2 3/4" (1,9 cm) 1/4" (6 mm) Drill Bit 1 Measure and mark location of hole on outside of right door as shown (Fig. A). Pre-drill hole with 1/4" drill. 2 Re-drill hole with 1/2" drill (Fig. A). Keep drilled hole square to trim to avoid breaking edge of 1-1/2" x 2-1/2" door stiffener. Screws 3/4" (1,9 cm) 2 RIGHT DOOR TOP VIEW Fig. A 1-3/4" (4,4 cm) 35-3/4" (90 cm) 1-3/4" (4,4 cm) 1/4" Pre-drill and 1/2" Drill-through 3 Install decorative hinges on horizontal trim and fl ush against hinge as shown. You have fi nished preparing your door for door handle. 39

42 Handle (locking) with Screws DOOR HARDWARE 1-1/4 Secure handle with 1-1/4" screws as shown. RIGHT DOOR Set Screw 1-1/4" Wood Screw Pre drill for screws 40

43 FRONT GABLE PANELS BJC 2 x 3 x 17-3/16" (5,1 x 10,2 x 43,7 cm) 6 1-1/2" (3,8 cm) 21-1/2 x 36" (54,6 x 121,9 cm) 21-1/2 x 36" (54,6 x 121,9 cm) 1 Measure distance from over-door trim to top plate (Fig. A). Fig. A TOP PLATE 2 Orient BJC on flat as shown. Transfer the measurement from Fig. A onto the left front gable panel. Place left front gable panel at measurement as shown. Secure using 1-1/2" nails. BJC (on flat) 1-1/2" (3,8 cm) Nails 1-3/4" (4,5 cm) Fig. A Measurement Primed side up 41

44 FRONT GABLE PANELS 3 Place gable center panel (use panel with vent hole) fl ush to installed left panel. Secure panel to BJC using 1-1/2" nails. 4 Place second BJC as shown under center panel as shown. Transfer the measurement from STEP - 1, Fig. A onto the center gable panel. Secure panel to BJC using 1-1/2" nails. BJC Primed side up BJC 1-3/4" (4,5 cm) Fig. A Measurement 1-1/2" (3,8 cm) Nails 5 Place right gable panel fl ush to installed center panel. Ensure panels are fl ush. Secure panel to BJC using 1-1/2" nails. 1-1/2" (3,8 cm) Nails BJC Primed side up Maintain You have fi nished assembling your front gable unit. 42

45 Front Gable Unit FRONT GABLE x4 x41 1 Center front gable unit on front wall top plate. Secure gable unit with 2 Nails. Fig. A 2" (5,1 cm) Nails TOP PLATE SPACED EVENLY 6" (15,2 cm) 2 Working inside, secure gable unit with 3" screws toe-screwed into BJC at an angle as shown in (Fig. B). Fig. B 3" (7,6 cm) Screws You have fi nished attaching your front gable. 43

46 BACK GABLE PANELS BJC 2 x 4 x 17-3/16" (5,1 x 10,2 x 43,7 cm) 6 1-1/2" (3,8 cm) 21-1/2 x 36" (54,6 x 121,9 cm) 21-1/2 x 36" (54,6 x 121,9 cm) 1 Orient BJC on flat as shown. Place left front gable panel as shown and secure using 1-1/2" nails. BJC (on flat) 1-1/2" (3,8 cm) Nails 1-3/4" (4,5 cm) Primed side up 1-1/2" (3,8 cm) 2 Place second BJC as shown under center panel as shown. Ensure panels are fl ush. Secure panel to installed BJC using 1-1/2" nails. 1-1/2" (3,8 cm) Nails Maintain Primed side up 1-3/4" (4,5 cm) BJC 1-1/2" (3,8 cm) 3 Place right gable panel fl ush to installed center panel. Ensure panels are fl ush. Secure panel to BJC using 1-1/2" nails. 1-1/2" (3,8 cm) Nails Maintain BJC Primed side up You have fi nished building your back gable assembly. 44

47 Back Gable Unit BACK GABLE x4 x41 1 Center back gable unit on front wall top plate. Secure gable unit with 2 Nails. Fig. A 2" (5,1 cm) Nails TOP PLATE SPACED EVENLY 6" (15,2 cm) 2 Working inside, secure gable unit with 3" screws toe-screwed into BJC at an angle as shown in (Fig. B). Fig. B 3" (7,6 cm) Screws You have fi nished attaching your front gable. 45

48 x8 x4 CLA 2 x 4 x 4-7/8" (5,1 x 10,2 x 12,4 cm) ECA 2 x 3 x 75-1/4" (5,1 x 7,6 x 191,1 cm) FRONT GABLE LADDERS x32 1 You will build two assemblies (Fig. B). Fig. B 2 Arrange, measure and mark locations of four CLA as shown place ECA on top. Secure using 3" screws as shown (Fig. A). Ensure parts are flush along edges. Fig. A 26-1/2" (67,3 cm) 48" (121,9 cm) 75-1/4" (191,1 cm) 3-1/2" (8,9 cm) 3" (7,6 cm) Screws ECA CLA x4 3 Flip over gable ladder sub-assembly and attach ECA to four CLA using 3" screws (Fig. C). Fig. C ECA Screws 4 Repeat STEPS 1-3 to build the second front gable ladder sub-assembly. 46

49 FRONT GABLE LADDERS x56 7/16 x 8-5/8 x 27-1/4" (1,1 x 21,9 x 69,2 cm) 7/16 x 8-5/8 x 48" (1,1 x 21,9 x 121,9 cm) Left Ladder Frame Right Ladder Frame 5 Arrange ladders and roof panels as shown (Fig. C) to make a right and a left gable assembly. Attach roof panels using 2" nails 6" apart. Note - panel over hangs ladder 3/4" (1,9 cm) along edge. NOTE: Install OSB with the rough side up Fig. D 7/16 x 8-5/8 x 48" 6" (15,2 cm) 7/16 x 8-5/8 x 27-1/4" Right Assembly 3/4" (1,9 cm) Left Assembly Nails END VIEW Panel overhang = 3/4" Right Left 3/4" (1,9 cm) You have fi nished building your gable assemblies. 47

50 FRONT GABLE OVERHANG Place the left gable unit onto rafter as shown (Fig. A). Ensure gable unit is fl ush against gable panel, fl ush at peak (Fig. B). Secure gable unit panel to rafter using 2" nails 6" apart (Fig. A). Nails Fig. B Fig. A 6" (15,2 cm) 2 Repeat STEP-1 for right gable unit. Ensure gable unit is flush against installed gable unit at the top. Secure right and left gable unit's framing to rafter using 3" screws as shown (Fig. C) Screws 6" (15,2 cm) Fig. C Nails Screws You have fi nished installing your gable units. 48

51 7/16 x 20-5/8 x 27-1/4" (1,1 x 52,4 x 121,9 cm) ROOF PANELS 02 7/16 x 48 x 96" (1,1 x 121,9 x 243,8 cm) Roof panels may cause serious injury until securely fastened. Note: all roof panels need to be installed with the rough side up (painted grid lines). 1 Attach a 48" x 96" panel with a 3/4" measurement on the rafter (Fig. C), flush to the edge of gable overhang panel and rafter bottom ends (Fig. A). Secure panel with two 2" nails in the corners. 3/4" (1,9 cm) Two Nails Fig. C Gauge Block 48" x 96" at rafter ends. Fig. A 2 Attach a 20-5/8" x 27-1/4" roof panel flush to the installed panel and flush to the rafter bottom ends (Fig. A). Secure panel with two 2" nails in the corners. 20-5/8" x 27-1/4" Two Nails Fig. A at rafter ends. 49

52 ROOF PANELS 7/16 x 27-1/4 x 48" (1,1 x 69,2 x 121,9 cm) 3/4" GAUGE BLOCK 3 Secure top of each lower panel using one 2" nail into each rafter, as shown (Fig. B). Maintain spacing at 24" between the centers of the rafters. Fig. B 20-1/4" (51,4) cm) 24" (61) cm) 24" (61) cm) 24" (61) cm) 24" (61) cm) 2" Nails 4 Attach a 27-1/4" x 48" roof panel with a 3/4" measurement on the rafter (Fig. C), fl ush to the lower panel and fl ush to the edge of gable overhang panel. Secure panel with two 2" nails in the corners. 3/4" (1,9 cm) Fig. C Gauge Block 27-1/4"x 48" 50

53 ROOF PANELS 7/16 x 20-5/8 x 48" (1,1 x 55,6 x 121,9 cm) 7/16 x 27-1/4 x 48" (1,1 x 69,2 x 121,9 cm) 3/4" GAUGE BLOCK 5 Attach another 27-1/4" x 48" roof panel with a 3/4" measurement on the rafter (Fig. C) and flush to the installed panels. Secure panel with two 2" nails in the corners. 3/4" (1,9 cm) Fig. C Gauge Block 27-1/4"x 48" Two Nails 6 Attach a 20-5/8" x 48" roof panel flush to the installed panels as shown. Secure panel with two 2" nails in the corners. 20-5/8" x 48" 51

54 ROOF PANELS 7 Secure top of each lower panel using one 2" nail into each rafter, as shown (Fig. D). Maintain spacing at 24" between the centers of the rafters. Fig. D 20-1/4" (51,4) cm) 24" (61) cm) 24" (61) cm) 24" (61) cm) 24" (61) cm) 2" Nails 8 Secure the roof panels using 2" nails 6" apart on edges and 12" apart inside panel. 6" (15,2 cm) 12" (30,5 cm) 9 Repeat STEPS 1-8 to attach roof panels on the opposite side. You have fi nished installing your roof panels. 52

55 FRONT GABLE SOFFITS 3/8 x 7-7/8 x 73-5/16" (1 x 20 x 186,2 cm) x40 1 Ensure soffit panels are flush at seam (Fig. B) and flush at peak. Position right and left 73-5/16" overhang panels primed side down, fl ush to front wall (Fig. A), centered with gable panel seam (Fig. B), and fl ush at peak (Fig. C). Secure panels with 2" fi nish nails. Fig. B Fig. C Fig. A 8" (20,3 cm) at center seam. Center and at peak. Nails 0 per side to wall. Primed Side Down You have fi nished installing your soffi t panels. 53

56 3/8 x 5-7/8 x 45-3/8" (1 x 14,9 x 115,3 cm) 3/8 x 5-7/8 x 72-3/4" (1 x 14,9 x 184,8 cm) EAVE SIDE SOFFITS 8 1 Ensure soffit panels are flush at rafter ends (Fig. B) and flush at seam. Position 72-3/4" and 45-3/8" soffi t panel primed side down, fl ush to front gable soffi t and rafter ends (Fig A). Toenail at center seam (Fig. C). Secure using (8) 2" fi nish nails, two in each rafter. Fig. A Fig. B 72-3/4" Nails Fig. C TOENAILING Primed Side Down Seam at seam 45-3/8" You have fi nished installing your eave side soffi t panels. 54

57 EAVE SIDE FASCIA x32 3/8 x 4-3/4 x 45-3/8" (1 x 12,1 x 115,3 cm) 3/8 x 4-3/4 x 80-5/8" (1 x 12,1 x 204,8 cm) 1 Ensure fascia panels are flush at seam (Fig. B). Position 80-5/8" and 45-3/8" fascia panels with primed side out, fl ush with roof panels (Fig. A). Install the 80-5/8" panel fl ush with front gable assembly as shown. Secure using 2" fi nish nails into rafter ends. Fig. B TOENAILING 45-3/8" at seam 80-5/8" Primed Side Out with roof panel. Fig. A Finish Nails DOOR You have fi nished installing your eave side fascia. 55

58 3/8 x 4-3/4 x 75-7/8" (1 x 12,1 x 192,7 cm) 3/8 x 4-3/4 x 75-7/8" (1 x 12,1 x 192,7 cm) GABLE TRIM SHIM 3/8 x 3-1/4 x 5-7/8" (1,0 x 8,3 x 14,9 cm) Painted Red Painted Green x34 1 Install 3-1/4 x 5-7/8" SHIMS on the back wall rafter, as shown (Fig. A). 2 Install trim fl ush at peak and to roof panels as shown (Fig. B, Fig C). Finish Nail per side Fig. A SHIM at peak. Fig.B Finish Nails x8 per side SPACED EVENLY Primed Side Out with top of OSB roof panels Fig. C 3 Repeat STEP 2 to attach gable trim on the front side. (Front side is without 3-1/4 x 5-7/8" shim.) You have installed your gable trim. 56

59 x4 x4 3/8 x 1-3/4 x 73-7/8" (1,0 x 4,4 x 187,6 cm) 3/8 x 1-3/4 x 74-1/2" (1,0 x 4,4 x 189,2 cm) CORNER TRIM x48 1 Attach corner trim as shown using 2" fi nish nails. 74-1/2" (189,2 cm) on gable wall Fig. A 73-7/8" (187,6 cm) on eave walls Fig. B under gable panel 73-7/8" (187,6 cm) 74-1/2" (189,2 cm) Seam is flush. Caulk seam before painting trim. You have attached your corner trim. 57

60 SHELVING x6 AE 2 x 3 0-1/8" (5,1 x 7,6 x 25,7 cm) x6 3/8 x 8 x 12-1/2" (1 x 20,3 x 31,8 cm) 8 1 Secure AE to bracket panels using three 2" nails. Assemble 6 shelf supports as shown; 5 right-side, 1 left-side. x5 Nail AE 2 Secure shelf supports at shown height with three nails. Corner Stud Nail LEVEL Left Shelf Bracket BACK WALL 53-1/2" (135,9 cm) FLOOR 58

61 7/16 x 11-7/8 x 96" (1,1 x 30,2 x 243,8 cm) KP 1 x 4 x 96" (2,5 x 10,2 x 243,8 cm) SHELVING 4 7/16 x 11-7/8 x 23-7/8" (1,1 x 30,2 x 60,6 cm) JS 1 x 4 x 23-7/8" (2,5 x 10,2 x 60,6 cm) 4 1-1/4" (3,2 cm) 3 Install shelf panels centered over shelf supports. Secure with 1-1/4" screws at each support. 1-1/4" (3,2 cm) Screws 96" (243,8 cm) 23-7/8" (60,6 cm) 4 Secure KP and JS with 2" nails at each support as shown. Nails KP JS You have fi nished installing your shelf. 59

62 RL 2 x 4 x 24" (5,1 x 10,2 x 61 cm) TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) LOFT 4 1 Orient parts TP and RL on a flat surface. Spread glue across RL and TP as shown (Fig. A). Hold parts TP and RL flush and aligned. 2 Assemble joist with 3" nails in a staggered pattern. RL Glue Fig. A TP TP RL Nails 2 3 Turn assembled joist over and repeat staggered nail pattern. 5 Support and drill a 7/16" hole through each end the joist (Fig. B). 1-3/4" (4,4 cm) 1-3/4" (4,4 cm) Fig. B 60

63 LOFT RL 2 x 4 x 24" (5,1 x 10,2 x 61 cm) TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 4 x4 (NOT ACTUAL SIZE) 3/8" x5-1/2" (1 cm x 14 cm) Hex Bolt 3/8" (1 cm) Flat Washer Pre-Assembled Loft Joist 2 x 4 x 120" (5,1 x 10,2 x 304,8 cm) 3/8" (1 cm) Lock Nut 6 Locate TP and RL flush to bottom of top plate and aligned at seam. Secure with 3" nails at wall studs and seam. TP RL Nails GABLE WALL at SEAM 7 Clamp or hold Pre-Assembled Loft Joist in place flush under top plate. Drill through joist and wall studs with 7/16" drill bit as shown. 8 Secure joist with hex bolts, flat washers and lock nuts at both sides (Fig. C). Tighten lock nuts securely. Fig. C 61

64 LOFT /2" x 96" (52,1 x 243,8 cm) 9 Install loft panel centered over loft joists. Secure with 2" nails 8" apart. There will be a gap of approximately 8-1/2" on either side. Nails 8" (20,3cm) Attention: Load not to exceed 400 lbs (181 kg) evenly distributed across loft. You have fi nished installing your loft. 62

65 COLLAR TIE HJ 1 x 3 x 72" (2,5 x 7,6 x 182,9 cm) x6 1 Position and level collar tie on 3rd rafter from back. HINT: For best appearance install collar tie on rafter facing away from door opening. 2 Attach with 2" nails as shown. HJ 3rd Rafter LEVEL Nails LOFT You have fi nished installing your collar tie. 63

66 TRANSOM WINDOW Transom Window x8 3/4" (1,9 cm) 1 Seal window behind fl ange edges with high-quality exterior-grade caulk before installing (Fig. A). Place transom window in gable opening. Ensure window is level and centered. Transom Window Fig. A 3/4" (1,9 cm) Screws HINT: Caulk behind frame near edge before installing. 2 Attach window using (8) 3/4" screws as shown (Fig. A). 64

67 YR 19/32 x 2-1/2 x 32-3/4" (1,5 x 6,3 x 83,1 cm) TRANSOM WINDOW 2 EY 19/32 x 2-1/2 x 9" (1,5 x 6,3 x 22,8 cm) 2" (5 cm) 3 Mark centers and install window trim over transom window using 2" fi nish nails. YR 2" Finish Nails EY Center of Window 4-1/2" (11,4 cm) Mark Center EY YR Do not nail into window flange. You have fi nished installing your transom window and trim. 65

68 WALL VENT 2 1/2" (1,3 cm) 8 x 16" (20,3 x 35,6 cm) 1 Choose walls for vent locations. Measure and mark vent hole in wall as shown. Cut out marked opening. 2 Caulk behind vent fl anges. Secure using 1/2" (1,3 cm) screws. For best ventilation install one vent low and the other high. 14" (35,6 cm) Caulk 6" (15,2 cm) 3 5" (7,6 12,7 cm) You have fi nished installing your wall vent. 66

69 PAINT & CAULK - NOT INCLUDED - Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: Bottom edge of all siding and trim Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting. (Follow directions provided by manufacturer.) ROOF FELT - NOT INCLUDED - Install felt flush to all roof edges overlapping 3". Use minimal amount of roofi ng nails to hold in place. OK to overlap at ridge. 3" OVERLAP DRIP EDGE - NOT INCLUDED - Install drip edge over roof felt on gable side and under roof felt on eave side (Fig. A). Do not use nails on side of drip edge that hangs over side of building. Only nail top of drip edge as shown. Roof Felt Drip Edge Drip Edge Fig. A Edge flush to trim. Snip bottom side of drip edge and bend over to other side of roof. (Follow directions provided by manufacturer.) 67

70 SHINGLES - NOT INCLUDED - Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch SHINGLE NAIL PATTERN Notch 1" (2,5 cm) 1/2" (1,3 cm) Sealing Strip 1" (2,5 cm) Half A Rain Slot Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. 1 Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle. Starter row must be straight and level all the way across with lower edge of roof deck. NOTE: If you have installed drip edge install shingles flush to drip edge. FRONT OF SHED BACK OF SHED (4) Nails TABS UP 1" (2,5 cm) overhang or flush with drip edge. Shingle overlaps roof decking. 1" (2,5 cm) overhang past roof deck. 68

71 SHINGLES continued Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge. FRONT OF SHED 1" (2,5 cm) Roof Deck BACK OF SHED Notch - or - with starter row. Drip Edge with starter row. Notch 3 Install second row of shingles flush at top of first row's rain slots. Ensure 1" overhang or flush to drip edge at front, stagger each row. FRONT OF SHED BACK OF SHED Notch 1" (2,5 cm) with rain slots. with rain slots. 4 Continue installing rows of shingles by staggering at front. 1" (2,5 cm) FRONT OF SHED Notch 69

72 SHINGLES continued... 5 Continue installing rows of shingles to the peak. At the peak make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at ridge cut to peak with a utility knife. Cut Off. 5" (12,7 cm) MAX. Top of rain slot. CUT 5" (12,7 cm) or less. If more than 5" to rain slot you must install another row of shingles. 6 Repeat steps 1-5 to shingle the opposite side of your roof. Trim shingles at ridge. 7 Once both sides are shingled you need to trim ends. Strike a chalk line 1" from edge. 8 Using your shingle hooked blade carefully cut shingles along chalk line. You have fi nished shingling your roof. Proceed to capping the ridge. 70

73 SHINGLES - RIDGE CAP You will finish off the top of the roof with a ridge cap made from shingles. 1 Cut shingles into THREE pieces. 2" (5 cm) 2" (5 cm) Hint: Use cut-off pieces first. 2" (5 cm) 2" (5 cm) 2" (5 cm 2" (5 cm) Score shingle, then snap-off angled cut. Weather Seal Top of slot. Note: You will need about cut pieces. 24 to 26 Pieces 2 Install first ridge cap flush to shingles at front, as shown. (1) Nail per side through weather seal. FRONT OF SHED 3 Install second ridge cap 5" back, as shown. (1) Nail per side through weather seal. 5" 12,7 cm FRONT OF SHED 71

74 SHINGLES - RIDGE CAP continued... 4 Continue installing ridge cap to back of roof. 5 Make sure there is 4" between the shingle-color and edge of shingles. 4" (10 cm) Trim cap off flush to shingles 6 When you have 4" minimum of shingle color cut one piece to cap your roof. Cut at top of rain slot. Cap 7 Install fl ush to shingles. to shingles (2) Nails per side. You have fi nished your ridge cap. 72

75 WARRANTY REGISTRATION Please complete your warranty registration to properly validate your warranty. Register your product online at: LIMITED CONDITIONAL WARRANTY* Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for 1 year. 2. All accessories, hardware and metal components are warranted for 2 years. 3. All Oriented Strand Board (OSB) is warranted for 2 years 4. Siding and Trim is warranted for: 10 years: Value Series / Solar Shed 12 years: Classic Series / Architectural Series 15 years: Big Buildings 5. Solar Shed windows are warranted for 1 year. 6. Cedar lumber is warranted for 15 years. 7. Preserved Pine is warranted for 10 years. Backyard Storage Solutions, LLC will repair, replace or pay for the affected part. In no event shall Backyard Storage Solutions, LLC pay the cost of labor or installation or any other costs related thereto. All warranties are from date of purchase. If a cash refund is paid on an affected part, it will be prorated from the date of purchase. CONDITIONS The warranty is effective only when: 1. The unit has been erected in accordance with the assembly instructions. 2. The unit has been properly shingled and painted or stained and reasonably and regularly maintained thereafter. 3. The failure occurs when the unit is owned by the original purchaser. 4. Backyard Storage Solutions, LLC has received the warranty registration card within thirty (30) days of purchase and notification of the failure in writing within the warranty period specified above. 5. Backyard Storage Solutions, LLC has had reasonable opportunity during the sixty (60) days following receipt of notification to inspect and verify the failure prior to commencement of any repair work. REQUIREMENTS Storage Buildings To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit; shingle the roof and paint or solid-colored stain the siding using quality, 100% acrylic latex exterior product with a minimum of two (2) coats within thirty (30) days of assembly; caulk above all doors and all horizontal and vertical trim boards; paint and seal all exposed edges, sides and faces of siding/trim and OSB siding to include all exterior walls and all sides and all edges of doors. Gazebos & Pergolas To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit. This includes treating all of the exposed cedar and pine surfaces on your gazebo or pergola structure with an exterior grade wood preservative, an exterior oil-based semi-transparent stain, an acrylic latex exterior paint or an acrylic latex solid color exterior stain within 30 days of assembly and as needed thereafter to maintain your warranty. Keep vegetation trimmed away from building and make sure siding panels and trim do not come in contact with masonry or cement. The minimum ground clearance for siding must be one half inch (½ inch) from concrete slab or two and one half inches (2 ½ ) from the ground when building is erected or constructed on a treated wood floor kit. Water from sprinklers must be kept off unit. In no event will Backyard Storage Solutions, LLC be responsible for any indirect, incidental, consequential or special damages nor for failure(s) that are caused by events, acts or omissions beyond our control including, but not limited to, misuse or improper assembly, improper maintenance (which eventually leads to rot or decay) and acts of God. Backyard Storage Solutions, LLC will not be held responsible for any labor costs incurred to construct your unit. This warranty gives you certain specific rights that vary from state to state. CLAIM PROCEDURE To make a claim under this warranty, you can either call or customerservice@backyardproducts.com. Please have ready the information below when you call or include the information in your 1. The model and size of the product. 2. A list of the part(s) for which the claim is made. 3. Proof of purchase of the Backyard Storage Solutions, LLC item, as shown on the original invoice. 4. Run code: found on exterior product label or assembly instructions enclosed in the product package. All other inquiries can be mailed to: Backyard Storage Solutions, LLC Attn: Customer Service 1000 Ternes Monroe, MI *WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A. IMPORTANT: This is your warranty certificate. LDR: 1/18/2016