w w w. h d o n l i n e s h o p. d e VRSCF RIGID SADDLEBAGS GENERAL PREPARATION -J04704 REV Kit Number Models Tools and Supplies Required
|
|
- Aldous Mitchell
- 5 years ago
- Views:
Transcription
1 -J070 REV VRSCF RIGID SADDLEBAGS GENERAL Kit Number 7-0 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of (English only).. See Figure. Remove the four rear fender mounting bolts () and washers (), and the passenger grab strap (). If necessary, move the ECM to better access the fender mounting bolts. is0a Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00a) Maximum saddlebag weight capacity is 0 pounds (. kg). Tools and Supplies Required Loctite Threadlocker and Sealant - Blue (H-D Part Number -7) is required for the proper installation of this kit. The rider's safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00a) This instruction sheet references service manual information. A service manual for this model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure and Table. PREPARATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00b). Refer to the service manual and follow the instructions given to remove the main fuse.. Remove the rider seat and passenger pillion per the instructions in the service manual.. Bolt (). Washer (). Grab strap Figure. Fender Mounting Bolts. Disconnect the six-way tail lamp socket housing and fourway turn signal lamp socket housing from the vehicle main harness following the instructions in the service manual. Disconnect the two-way license-plate illuminator socket housing from the tail lamp harness.. If a luggage rack, sissy bar upright or both have been mounted on the rear fender, remove the two screws and washers, and two carriage bolts and nuts that secure the luggage rack bracket to the seat pan. The rack and/or upright will remain attached to the rear fender when the fender is removed.. Remove the rear fender from the seat pan by lifting upward and sliding the fender back. 7. If a center-mounted license bracket is installed, it can remain attached to the seat pan. -J070 of
2 If a side-mounted license bracket is installed: a. Remove the license plate from the vehicle (if installed), and set aside for later installation. b. See Figure. Remove the two bolts () holding the side license-plate bracket () to the seat pan (). c. Remove the license-plate adjuster bracket () carriage bolt (), washer () and lock nut (), and the licenseplate illuminator () and screws (7) from the bracket. d. The original equipment (OE) license-plate bracket (), screws (7) and bolts () can be discarded. Set the remaining items aside for installation to the new side license-plate bracket.. Remove and discard the rear side reflectors (0). If a center-mounted license bracket is installed, remove the reflectors from the license bracket sides. Remove any residual adhesive from the bracket. If a side-mounted license bracket is installed, remove the reflectors from the upper frame just forward of the shock absorbers. Remove any residual adhesive from the reflector mounting area on the frame. Access to the shock absorber adjustment collar is more difficult with the saddlebags in place.. Adjust the rear suspension preload, if desired, per the instructions in the service manual. is0 7 SADDLEBAG BRACKET INSTALLATION. See Figure. Obtain the right-side saddlebag adapter bracket (), two M0 x 0 mm (0.7 inch) long button head cap screws () and two M0 hex nuts () from the kit.. Apply a few drops of Loctite - Blue to the screw threads. Attach the adapter bracket to the outside of the seat pan () with the screws and nuts, and tighten to 7. Nm ( ft-lbs).. Repeat steps and for the left-side saddlebag adapter bracket.. Obtain the right-side saddlebag mounting bracket (), two M0 x mm (0. inch) long hex socket head cap screws (), two M0 x mm (.00 inch) long hex socket head cap screws (7) and two M0 flat washers () from the kit.. Apply a few drops of Loctite - Blue to the threads of the two shorter screws (). Attach the saddlebag mounting bracket to the saddlebag adapter bracket () with the short screws and flat washers, but do not fully tighten. is Side license-plate bracket. License-plate adjuster bracket. Carriage bolt. Washer. Lock nut. License-plate illuminator 7. Illuminator attaching screw (). License-plate bracket attaching screw (). Seat pan 0. Reflector () Figure. Original Equipment License Plate Bracket. Saddlebag adapter bracket. Button head cap screw, 0 mm (0.7 inch) long (). Hex nut (). Saddlebag mounting bracket. Socket head cap screw, mm (0. inch) long (). Flat washer () 7. Socket head cap screw, mm (.00 inch) long (). Seat pan. Tab on vehicle frame Figure. Saddlebag Bracket Installation. Apply a few drops of Loctite - Blue to the threads of the two longer screws (7). Attach the saddlebag mounting bracket to the tab () on the vehicle frame just forward of the shock absorber. Alternately tighten all four screws to. Nm ( ft-lbs). -J070 of
3 7. Repeat steps through for the left-side saddlebag mounting bracket. ALL installations: Close the seat.. If a center-mounted license bracket is installed on the fender, the side-mount license-plate relocation kit () can be discarded. See Figure. If a side-mounted license bracket was installed on the vehicle: a. Obtain the side-mount license-plate relocation kit () from the saddlebag kit, and the license-plate adjuster bracket (A) carriage bolt (B), washer (C), lock nut (D) and license-plate illuminator (E) removed earlier. b. Apply a few drops of Loctite - Blue to the threads of the three M screws (7), and install the licenseplate bracket () to the inboard side of the left saddlebag mounting bracket (). Tighten the screws to. Nm (0 ft-lbs). c. Apply a few drops of Loctite - Blue to the threads of the two M screws (). Insert the screws through the illuminator (E) and the tab on the license-plate bracket (), and thread into the illuminator cover () as shown. Seat the lens securely to the bracket tab, but DO NOT overtighten. d. Install the adjuster bracket (A) with the carriage bolt (B), washer (C) and lock nut (D). Install the license plate (if removed). Tighten the lock nut securely. When installing the rear fender, verify that the three wiring harnesses and connectors are routed through the low spot in the seat pan to make sure there is adequate clearance between the rear fender and the seat pan.. Install the rear fender and passenger grab strap per the instructions in the service manual, taking care to correctly route the harness. 0. If a luggage rack, sissy bar upright or both are mounted on the rear fender, secure the luggage rack bracket to the seat pan with the two screws and washers, and two carriage bolts and nuts removed earlier. Tighten the nuts and screws to 7- Nm (-0 in-lbs).. Connect the six-way tail lamp socket housing and fourway turn signal lamp socket housing to the vehicle main harness following the instructions in the service manual. Connect the two-way license-plate illuminator socket housing to the pin housing on the tail lamp harness. Stow the harnesses and connectors to make sure they are not damaged and remain clear of the rear tire.. Install the passenger pillion per the instructions in the service manual.. If installing a gas shock seat strut kit () to the rider seat, follow the instructions in that kit. If NOT installing a gas shock seat strut kit, install the rider seat per the instructions in the service manual. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) SADDLEBAG REFLECTOR INSTALLATION. Obtain the right-side saddlebag () and a reflector kit ().. See Figure. Place the saddlebag on a smooth, clean surface so that the "Harley-Davidson" script () on the side of the bag is facing upward.. Measure and mark as shown ( and ) with a paint pen or marker to identify the drilling locations ().. Carefully drill two - mm (/ inch) diameter holes through the soft outer surface and the hard inner saddlebag tub. Remove any burrs and debris.. See Figure. Insert the posts on the reflector mount () through the drilled holes, and fasten with two push nuts ().. Clean the recesses of the reflector mount with isopropyl alcohol to remove any oils or debris. 7. Remove the liner from the adhesive backing of the reflector (0). Carefully position the reflector to the mount, and press firmly into place, holding the reflector in position with steady pressure for a few moments.. Repeat Steps through 7 with the left-side saddlebag. is07. - mm (.0-. inches) above logo.. mm (.7 inch) apart, centered in area. Drill two - mm (/-inch) diameter holes. "HARLEY-DAVIDSON" script Figure. Reflector Position on Saddlebag -J070 of
4 SADDLEBAG INSTALLATION. Obtain twelve M x mm (0. inch) long screws () from the kit.. Apply a few drops of Loctite - Blue to the threads of six screws, and install the right-side saddlebag () to the saddlebag mounting bracket (). Tighten the screws to. Nm (0 ft-lbs).. Repeat Step for the left-side saddlebag. RETURN TO SERVICE. Verify that the ignition/key switch is turned to the OFF position. Refer to the service manual and follow the instructions given to install the main fuse. SERVICE PARTS is0 B C A 0 E D Figure. Service Parts, VRSCF Rigid Saddlebags -J070 of
5 SERVICE PARTS Table. Service Parts Table Item Description (Quantity) Saddlebag, right side Saddlebag, left side Hex socket button head cap screw, M x mm (0. inch) long () Bracket, saddlebag mounting (right) Bracket, saddlebag mounting (left) Hex socket head cap screw, M0-. x mm (0. inch) long () 7 Flat washer, M0, heat treated () Hex socket head cap screw, M0-. x mm (.00 inch) long () Bracket, saddlebag adapter (right) 0 Bracket, saddlebag adapter (left) Hex socket button head cap screw, M0-. x 0 mm (0.7 inch) long () Hex nut, M0-. () Side-mount license plate relocation kit (includes items through 7) Bracket, license plate Cover, license plate illuminator Button head hex socket screw, M x 0 mm (0. inch) long () 7 Hex socket button head cap screw, M x mm (0. inch) long () Reflector kit () (includes items through ) 0 Reflector mount Reflector (red) Push nut () Gas Shock Seat Strut Kit Items mentioned in text, but not included in kit: A Original equipment (OE) license-plate adjuster bracket B OE license-plate bracket carriage bolt C D E OE flat washer OE flanged lock nut OE license-plate illuminator Part Number -0-0 M M 70M M 70M 0-0 M J070 of
BOOM! AUDIO AM/FM/WB HIDDEN ANTENNA
REV. 0-- BOOM! AUDIO AM/FM/WB HIDDEN ANTENNA GENERAL Kit Number 000 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationw w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models
-J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationw w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models
-J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For Toyota Tundra Kit 68505 This WARN Trans4mer system can be customized to give your Toyota Tundra a wide variety of looks, front-end protection
More informationHAPPY TRAILS PRODUCTS
Thank you for purchasing Happy Trails products. Our products are proudly hand made in Boise Idaho, USA. If you have any questions or concerns about the installation of this product, please contact us directly
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationBe sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
More informationFoot Rail. Nissan Navara_Frontier D23 DC START HERE! READ ME FIRST
Foot Rail Nissan Navara_Frontier D3 DC ENG FANN00 START HERE! READ ME FIRST Don t be a hero and muscle through this without first reading these fitting instructions! Improper installation of this gear
More informationBX Toyota Tacoma (Includes Prerunner) Installation Instructions
Attachment Tab Height: 11.5 Attachment Tab Width: 30.5" Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 19-1/2 Attachment Tab Width: 19 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationINSTALL LOAD BED TRACKS
Universal LOAD BED TRAY & Load BArs TRBU001 / KRLBUNI1 INSTALL TIME: 2.5 Hours READ ME FIRST: Thank you for purchasing a Front Runner Slimline II Load Bed Rack or Load Bar Kit. Your Kit will contain the
More informationDRAWER Mitsubishi pajero lwb
DRAWER Mitsubishi pajero lwb SSDS601 / SSMP001 INSTALL TIME: 45 mins Thank you for purchasing a Front Runner Storage System. This Storage System is made up of the following components: 1. A Drawer System
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAVVY OFF ROAD GAS TANK SKID INSTALLATION INSTRUCTIONS
It is best to work with a fuel tank that has the least amount of fuel in it as possible. Thank you for purchasing the best skid on the market. Please follow these instructions and your installation should
More informationHiniker Company th St. P.O. Box 3407 Mankato, MN VEHICLE INSTALLATION INSTRUCTIONS FOR: CHEV/GMC 4x4: K1500 SILVERADO/SIERRA
VEHICLE INSTALLATION INSTRUCTIONS FOR: CHEV/GMC x: 007 03 K500 SILVERADO/SIERRA Page of 5 Hiniker Company 58766 0th St. P.O. Box 307 Mankato, MN 5600 INSTRUCTION SHEET NO: 505 Rev. A August 0, 03 IMPORTANT:
More informationC6 Corvette Rear Spoiler Kit CDC #
2005 2008 C6 Corvette Rear Spoiler Kit CDC # 0542 7002 01 Note: Read installation instructions before starting Kit Includes: 1 C6 Rear Spoiler 2 CHMSL Bracket # 0542-3500-01 2 Screw 4.2 x 1.41 x 25 # 30005
More informationQUICK DETACH BACKREST KIT HARLEY-DAVIDSON FL TOURING MODELS (EXCEPT FLHTC/I & FLHTCUI) PARTS INCLUDED
PARTS INCLUDED 1 - Backrest Assembly 1 - Right Side Bracket Assembly 1 - Left Side Bracket Assembly 1 - Adapter Bracket, Left 1 - Adapter Bracket, Right 6-3/8 x1/8 Mounting Spacer 2-1/4 x1/8 Mounting Spacer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationINSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN Application: YAMAHA BIGBEAR 00+
INSTALLATION INSTRUCTIONS ATV WINCH MULTI-MOUNT Multi-Mount Mounting-Kit: PN 61025 Application: YAMAHA BIGBEAR 00+ Your safety, and the safety of others, is very important. To help you make informed decisions
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK005 / KRJW016T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK004 / KRJW016T INSTALL TIME: 2 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: End User: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating
More informationYJ DeFenders. These installation instructions apply to the following Poison Spyder products:
INSTALLATION INSTRUCTIONS INST-13-02-070_A YJ DeFenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation. If
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For Chevrolet Silverado 1500HD & 2500 Kit 68162 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of
More informationIntercooler Shroud and Belt Cover for WRX
Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 645 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationFRONT BUMPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
FRONT BUMPER KIT P/N 2882301 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationWARNING Honda Civic (Incl. EX, LX, DX) Installation Instructions BX2243. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationE4-WM5-Y542A00 MOUNTING INSTRUCTION
This instruction is for both left front (driver) 41-269282 and right front (passenger) 41-269299 B8 8112 shocks. A step by step process is shown with images of the right front. The left front is a mirror
More informationPLOW MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL
PLOW MOUNT KIT FOR POLARIS RANGER P/N 34-3010 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be sure all parts
More information======================================================================================== ( DR / DR) JK WRANGLER MOD RACK
(10984 4DR / 10982 2DR) JK WRANGLER MOD RACK INSTALLATION SHEET Important Notes: Some brands of windshield light brackets and snorkels may not be compatible with the 10984 MOD Rack System. Body lifts are
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2012-14 Chevy Captiva Sport Attachment Tab Height: 21-1/2 Serial Number Attachment Tab Width: 18-1/2 Please read BOTH these and the General Instructions prior to installing or operating this equipment.
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Serial Number BX3620 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationPLOW MOUNT KIT FOR CAN-AM MAVERICK P/N ASSEMBLY / OWNERS MANUAL
PLOW MOUNT KIT FOR CAN-AM MAVERICK P/N 34-7030 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be sure all parts
More informationJK Rear Inner Fenders
INSTALLATION INSTRUCTIONS INST-17-05-080_A JK Rear Inner Fenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationBUSHTEC TRAILER HITCH FOR VICTORY VISION Trailer Hitch Installation Instructions READ ALL INSTRUCTIONS BEFORE YOU START
BUSHTEC TRAILER HITCH FOR VICTORY VISION Trailer Hitch Installation Instructions READ ALL INSTRUCTIONS BEFORE YOU START ATTENTION INSTALLER: THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER!!! VICTORY
More informationWARNING. BX Ford F350 (Includes Super Duty) Installation Instructions
Serial Number BX231 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationHARLEY TRI-GLIDE TRAILER HITCH INSTALLATION INSTRUCTIONS LAST UPDATED 11/5/2011 REV: B
HARLEY TRI-GLIDE TRAILER HITCH INSTALLATION INSTRUCTIONS LAST UPDATED 11/5/2011 REV: B Thank you for choosing the Motor Trike trailer hitch for your trike. We ask that you read the directions before you
More informationSlide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:
RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationContractors Rack Assembly and Installation Instructions
Part # 18601 & 16601 Contractors Rack Assembly and Installation Instructions 4751 Littlejohn St. Unit A, Baldwin Park, CA 91706 Page 1 of 12 11/13/08 Thank you for purchasing the Paramount Restyling Contractors
More informationJeep Wrangler JK & 4-Door Front Pair Part # Revision H
Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with
More informationFlat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationinstallation guide 1 GUIDE#: pwb-assault-004
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More informationASSEMBLY & INSTALLATION GUIDE
ASSEMBLY & INSTALLATION GUIDE APPLICATION GM Truck (Full-size Trucks) PART # 74805-00A (Silver) 74805-0A(Black) INSTALLATION TIME Hour SKILL LEVEL 2 3 4 = Easy TOOLS REQUIRED Phillips screw driver Torx
More informationJEEP CARGO SLIDE IMPORTANT WARNING! SSST001. INSTALL TIME: 45 mins
JEEP CARGO SLIDE SSST001 INSTALL TIME: 45 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
More informationRusty s JL Winch Mount RR-WM55-JL INSTALLATION INSTRUCTIONS
Rusty s JL 2018+ Winch Mount RR-WM55-JL INSTALLATION INSTRUCTIONS Introduction: Rusty s recommends that this installation be performed by a certified automotive technician or a person with professional
More information4-Door Rear XHD Armor Fenders
Page 1/10 Part #11615.02 Page 2/10 1 4 2 3 5 Components 1. Left Rear Fender (1) 2. Right Rear Fender (1) 3. Left Rear Guard (1) 4. Right Rear Guard (1) 5. License Plate Bracket (1) OMIX-ADA TECHNICAL SUPPORT
More informationFORD RANGER Onwards SLIMLINE II RACK (1255MM x 1358MM)
FORD RANGER - 2012 Onwards SLIMLINE II RACK (1255MM x 1358MM) FAFR001 / KRFM010T INSTALL TIME: 60 mins READ ME FIRST: Thank you for purchasing a Front Runner Slimline II Rack. This Roof Rack consists of
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationPLOW MOUNT KIT FOR KAWASAKI TERYX, YAMAHA RHINO P/N ASSEMBLY / OWNERS MANUAL
PLOW MOUNT KIT FOR KAWASAKI TERYX, YAMAHA RHINO P/N 34-2025 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be
More informationLAnd Rover defender TDI & TD5 Gullwing WINDOW Box. You will need to have installed a Gullwing Door before installing the Window Box.
LAnd Rover defender TDI & TD5 Gullwing WINDOW Box GWLD008 INSTALL TIME: 2 Hours You will need to have installed a Gullwing Door before installing the Window Box. IMPORTANT WARNING! IT IS CRITICAL THAT
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
(No Turbo) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products
More informationMetroboard Pulley Replacement Procedure
Metroboard Pulley Replacement Procedure 1) Remove the two transmission cover screws (1/8 allen driver). Then remove the transmission cover. Note there is a split lock washer and flat washer as well, so
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number 2012 Hyundai Accent (No Foglights) Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
(No Turbo) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/2 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationHONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More information2015 GMC Yukon. Upper Class Grille Insert
Upper Class Grille Insert TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationMETRICFATS.COM Thank you for purchasing your new Stealth Rear Turn Signals for your Yamaha Raider.
METRICFATS.COM Thank you for purchasing your new Stealth Rear Turn Signals for your Yamaha Raider. The instructional sheets that follow are thoroughly detailed and should be studied BEFORE picking up a
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationINSTALLATION QUICK ADJUST RELOCATOR FOR TOUR-PAK 8973
FOR TOUR-PAK 8973 PARTS INCLUDED 1 Base Plate Assembly 1 Right Side Extruded Slider Assembly 1 Left Side Extruded Slider Assembly 1 Filler Panel 1 Hardware Kit 1 Stop Block 2 1/4-20 x 1/2" Hex Head Cap
More informationBX Chevy Suburban/Tahoe (No Adaptive Cruise) 2015 GMC Yukon/Yukon XL (Includes Denali)
2015 Chevy Suburban/Tahoe (No Adaptive Cruise) 2015 GMC Yukon/Yukon XL (Includes Denali) (No Adaptive Cruise) Please read BOTH these and the General Instructions prior to installing or operating this equipment.
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 24-3/4 Attachment Tab Width: 21 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationWARNING. BX Kia Soul Installation Instructions. Bolt Torque Specifications. Bolt Torque Specifications
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationinstallation guide 1 GUIDE#: PWB-wwpontoon-pol-004
f250 pontoon WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks tower fits Pontoon boats with 96 to 102 inch wide beam widths. This measurement is taken from
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationFOLDING TONNEAU RACK. 1. Rack Rail Assembly
FOLDING TONNEAU RACK Package Contents (2) Load Bars (4) Load Bar End Caps (4) ¼-20 x 9/16 Narrow Shoulder Hex Head Screw (28) ¼ Flat Washers (24) ¼ Split Lock Washers (20) ¼-20 x ¾ long Button Head Screws
More informationIN-BED FRAME MOUNT INSTALLATION INSTRUCTIONS
Lit. No. 13666, Rev. 05 December 5, 2005 IN-BED FRAME MOUNT INSTALLATION INSTRUCTIONS FOR SINGLE-STAGE AND TWO-STAGE TAILGATE SPREADERS Read Owner's Manual before operating or servicing spreader. Empty
More informationCustom 3-Point Seatbelt Installation Guide for: Corvette
Custom 3-Point Seatbelt Installation Guide for: 1963-67 Corvette Note: The information enclosed in this installation guide is to be used as merely an outline to assist you during the process of installation.
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/4 Attachment Tab Width: 21-3/4 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products
More informationSEAT-831. Seat Box Kit. Club Car Precedent. Installation Instructions
SEAT-831 Seat Box Kit Club Car Precedent Installation Instructions Contents of SEAT-831 Seat Box Kit: a (1 ea.) Seat Box Platform b (1 ea.) Front Seat Box Plate c (1 ea.) Foot Plate d (1 ea.) Tailgate
More informationPage 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar
More informationBX3615. Subaru Impreza WRX (Include STI) Subaru 2012 Impreza Premium 2010 Outback Sport Installation Instructions Attachment Tab Height: 15
1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work. If needed, Blue
More informationJK Front Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-03-030_A JK Front Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationAssembly & Installation Instructions FOR VEHICLE MOUNT KIT USING VEHICLE CENTER MEMBER
Assembly & Installation Instructions FOR VEHICLE MOUNT KIT 991002 USING VEHICLE CENTER MEMBER 9910092 TO FIT 99 - LATER Chevrolet 2500 Silverado 4x4 and 3500 Pickup 4x4 99 - LATER GM 2500 Sierra 4x4 and
More informationWARNING. Bolt Torque Specifications Torque in Foot-Pounds for Inch Bolts Bolt Size Grade 5 Grade 8
1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work. If needed, Blue
More information