INSTALLATION QUICK ADJUST RELOCATOR FOR TOUR-PAK 8973
|
|
- Morgan Alexandra Harvey
- 6 years ago
- Views:
Transcription
1 FOR TOUR-PAK 8973 PARTS INCLUDED 1 Base Plate Assembly 1 Right Side Extruded Slider Assembly 1 Left Side Extruded Slider Assembly 1 Filler Panel 1 Hardware Kit 1 Stop Block 2 1/4-20 x 1/2" Hex Head Cap Screws 10 1/4-20 Nylon Locking Nuts 12 1/4" Flat Washers 8 1/4-20 x 7/8" Hex Head Cap Screws 10 1/4-20 x 1-3/8" Hex Head Cap Screws 4 #8 X 1/2 Phillips Head Screws 4 #8 Wide Flat Washers 1 Installation Instructions Please read and understand entire instructions before starting installation. THANK YOU FOR CHOOSING KϋRYAKYN! IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT. WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY. ATTENTION! This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality. This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage. TOOLS SUGGESTED Set of Hex Wrenches, Combination Wrenches, Socket Set with Ratchet, Drill & 17/64" Drill Bit STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS. STEP 1 This step is for all model years. Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition. Remove the seat. NOTE: Not compatible with amplifiers found on stock 08 and earlier Screamin Eagle models or included in H-D Enhanced Sound system. Not compatible with Leather Tour-Paks. NOTE: Will fit 98-early 00 Touring Models with rigid mounted Tour-Paks if the stock support bar has been updated to the late style support bar. CUSTOMER SERVICE (toll free) QUESTIONS techsupport@kuryakyn.com or call LIMITED WARRANTY Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions: Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s). The product must be properly installed, maintained and operated under normal conditions. Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products. Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between Küryakyn and a customer. Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended. Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D. S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from the date of purchase where as all other components shall be warranted for one(1) year. This includes, but is not limited to; control modules, wiring, chrome & other components. Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies with the manufacturer. ABOUT OUR CATALOG For purchasing Küryakyn products, you can receive a complete catalog free of charge. Send the Proof-of-Purchase below with your address to: Küryakyn, P.O. Box 339, Somerset, WI Please indicate either Accessories Catalog for Harley-Davidson or GL & Metric Cruisers. Be sure to ask your local dealer about other Küryakyn products, the motorcycle parts and accessories designed for riders by riders Küryakyn USA All Rights reserved. NOTE: Correct placement of specified hardware is extremely important for proper function of this product HD-0611 cont.-
2 WARNING! DO NOT EXCEED THE OEM WEIGHT LIMITATIONS OF THE TOUR-PAK. Instructions for Specific Models: For 09-up Touring models, including CVO Touring Models - Pg 2 For 09-up Touring models with detachable Tour-Pak - Pg 3 For Touring models - Pg 4 For Touring models - Pg 5 For Touring models with detachable Tour-Pak - Pg 6 PIC 1 For 09-up Touring Models Open the Tour-Pak and remove the liner. Remove the hardware securing the Tour-Pak to the support bracket - save this hardware, it will be re-used. Remove the Tour-Pak from the support bracket. PIC 1 On CVO models, there will be a black Amplifier support plate on the support bracket. Leave this plate in place. PIC 2 Rotate the Tour-Pak forward, resting it where the seat would be. Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket. SUPPORT BRACKET NOTE: Be careful of the wiring harness, cut any zip ties or wire clips securing the wiring harness. As shown in PIC 3, place the base plate over the support bracket. On CVO models, set the base plate on top of the black amplifier bracket that is on the support bracket. Line up the holes in the base plate with the threaded holes in the support bracket and thread the stock hardware removed in Step 2 through the base plate and in to the support bracket. Tighten the hardware. PIC 2 PIC 3 STOCK HARDWARE AMPLIFIER BRACKET (including preassembled) are tightened before operation of the improper installation. Periodic maintenance may be BASE PLATE On the underside of the Tour-Pak, hold the extruded aluminum sliders (as shown in PIC 4) in place lining up the holes in the Tour-Pak with the holes in the sliders. PIC 4 THIS GAP EVEN TOUR PAK REAR NOTE: It may be helpful to push the 1/4-20 x 7/8" hex head cap screws (with 1/4" washers) through the Tour-Pak first to help line up the sliders. As shown in PIC 4 (red circles), loosely install the 1/4-20 nylon locking nuts for now. NOTE: The hardware can be installed in either front or back holes. Make sure that the gap (PIC 4) between the sliders is equal and tighten the hardware securing the sliders to the underside of the Tour-Pak. NOTE: If sliders are not parallel, they will bind in the channels and the Tour-Pak will not move smoothly. PIC 5 TOUR PAK FRONT SLIDERS WITH LOCKING SHOES (including pre-assembled) are tightened before operation of the improper installation. Periodic maintenance may be STEP 7 As shown in PIC 5, align the sliders with the locking shoes on the base plate. The locking shoes fit inside the sliders. It may be necessary to loosen the locking shoes to get them to fit inside the sliders. BASE PLATE 2
3 STEP 8 STEP 9 Slide the Tour-Pak back until it stops. As shown in PIC 6, secure the stop block to the base plate using the 1/4-20 x 1/2" hex head cap screws and 1/4" flat washers. Place the stop block on top of the base plate and secure from the underside. PIC 6 Test that the Tour-Pak moves freely and that no wires are stretched or pinched at any point. Secure the wire harness so that the Tour-Pak can move freely. STEP 10 To secure the Tour-Pak in place, turn all 4 locks (PIC 7) until snug and rotate the levers up until they lock in place between the nylon anti-rotation stops. You should not need to use any type of tool for leverage to tighten the locks sufficiently. You should be able to feel the lever snap into place when folded over. If you do not feel a positive snap when folding the lever, it may be too tight. Loosen 1/2 turn and fold over again. Test that the Tour-Pak is secure before using the motorcycle. STOP PLATE Before each ride inspect to ensure the levers are folded over in place and that the Tour-Pak is secure. PIC 7 ANTI-ROTATION STOPS For 09-up Touring Models with Detachable Tour-Pak Open the Tour-Pak and remove the liner. Remove the hardware securing the Tour-Pak to the support bracket - save this hardware, it will be re-used. Remove the Tour-Pak from the support bracket and (if possible) put the Tour-Pak on a covered workbench. If installing on the bike, rotate the Tour- Pak forward, resting it where the seat would be. Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket. LOCKING LEVER NOTE: Be careful of the wiring harness, cut any zip ties or wire clips securing the wiring harness. PIC 8 Place the base plate over the support bracket. Line up the holes in the base plate with the holes in the support bracket (PIC 8) and secure using the stock hardware removed in Step 2 through the base plate and in to the support bracket. Tighten the hardware. Using a 17/64" drill bit, drill holes through the front stop block mounting holes in the base plate and through the support bracket. (including pre-assembled) are tightened before operation of the improper installation. Periodic maintenance may be LINE UP THESE HOLES Follow Steps 4-10 in the "for 09-up Touring models" section above. Tighten all hardware and make sure the Tour-Pak is secure before operating the motorcycle. FOR '06-'08 Touring Models - Injection Molded Tour-Pak Open the Tour-Pak and remove the liner. Remove the hardware securing the Tour-Pak to the support bracket - save this hardware, some of it will be re-used. Remove the Tour-Pak from the support bracket and rotate the Tour-Pak forward, resting it where the seat would be. 3
4 Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket. NOTE: Be careful of the wiring harness, cut any zip ties or wire clips securing the wiring harness. PIC 9 As shown in PIC 9, place the base plate over the support bracket. Line up the holes in the base plate with the holes in the support bracket. Insert the 1/4-20 x 1-3/8"hex head cap screws and 1/4" flat washers through the 5 holes in the base plate. As shown in PIC 10, using the stock U-channels and stock washers, tighten the hardware. On the underside of the Tour-Pak, hold the extruded aluminum sliders (as shown in PIC 11) in place lining up the holes in the Tour-Pak with the holes in the sliders. LINE UP BASE PLATE WITH THESE HOLES NOTE: It may be helpful to push the 1/4-20 x 7/8" hex head cap screws (with 1/4" flat washers) through the Tour-Pak first to help line up the sliders. PIC 10 STOCK U CHANNEL As shown in PIC 11 (red circles), loosely install the 1/4-20 nylon locking nuts for now. NOTE: The hardware can be installed in either front or back holes. Make sure that the gap (PIC 11) between the sliders is equal and tighten the hardware securing the sliders to the underside of the Tour-Pak. STOCK WASHERS NOTE: If sliders are not parallel, they will bind in the channels and the Tour-Pak will not move smoothly. (including pre-assembled) are tightened before operation of the improper installation. Periodic maintenance may be PIC 11 MAKE THIS GAP EVEN TOUR PAK REAR STEP 7 STEP 8 STEP 9 STEP 10 As shown in PIC 5 on Page 2, align the sliders with the locking shoes on the base plate. The locking shoes fit inside the sliders. It may be necessary to loosen the locking shoes to get them to fit inside the sliders. Slide the Tour-Pak back until it stops. As shown in PIC 6 on Page 3, secure the stop block to the base plate using the 1/4-20 x 1/2" hex head cap screws and 1/4" flat washers. Place the stop block on top of the base plate and secure from the underside. Test that the Tour-Pak moves freely and that no wires are stretched or pinched at any point. Secure the wire harness so that the Tour-Pak can move freely. To secure the Tour-Pak in place, turn all 4 locks (PIC 7 on Page 3) until snug and rotate the levers up until they lock in place. You should not need to use any type of tool for leverage to tighten the levers sufficiently. You should be able to feel the lever snap into place when folded over. If you do not feel a positive snap when folding the lever, it may be too tight. Loosen 1/2 turn and fold over again. Test that the Tour-Pak is secure before using the motorcycle. Before each ride inspect to ensure the levers are folded over in place and that the Tour-Pak is secure. TOUR PAK FRONT 4
5 For '00-'05 Touring Models - Fiberglass Tour-Pak Open the Tour-Pak and remove the liner. Remove the hardware securing the Tour-Pak to the support bracket - save this hardware, some of it will be re-used. Remove the Tour-Pak from the support bracket and rotate the Tour-Pak forward, resting it where the seat would be. Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket. PIC 12 SELF TAPPING SCREWS FILLER PANEL NOTE: Be careful of the wiring harness, cut any zip ties or wire clips securing the wiring harness. Place the base plate over the support bracket (PIC 9 on Page 4). Line up the holes in the base plate with the holes in the support bracket. Insert the 1/4-20 x 1-3/8" hex head cap screws and 1/4" flat washers through the 5 holes in the base plate. As shown in PIC 8, using the stock U-channels and stock washers, secure the base plate to the support bracket using the nylon locking nuts. Tighten the hardware. Secure the filler panel (PIC 12) loosely behind both the extruded aluminum sliders using the 4 self tapping screws and #8 wide flat washers. On the underside of the Tour-Pak, hold the extruded aluminum sliders (as shown in PIC 11 on Page 4) in place lining up the holes in the Tour-Pak with the holes in the sliders. NOTE: It may be helpful to push the 1/4-20 x 1-3/8" hex head cap screws (with 1/4" flat washers) through the Tour-Pak first to help line up the sliders. As shown in PIC 11 on Page 4 (red circles), loosely install the 1/4-20 nylon locking nuts for now. NOTE: The hardware can be installed in either front or back holes. Make sure that the gap (PIC 11 on Page 4) between the sliders is equal and tighten the hardware securing the sliders to the underside of the Tour-Pak. NOTE: If sliders are not parallel, they will bind in the channels and the Tour-Pak will not move smoothly. STEP 7 STEP 8 STEP 9 As shown in PIC 5 on Page 2, align the sliders with the locking shoes on the base plate. The locking shoes fit inside the sliders. It may be necessary to loosen the locking shoes to get them to fit inside the sliders. Slide the Tour-Pak back until it stops. As shown in PIC 6 on Page 3, secure the stop block to the base plate using the 1/4-20 x 1/2" hex head cap screws and 1/4" flat washers. Place the stop block on top of the base plate and secure from the underside. Test that the Tour-Pak moves freely and that no wires are stretched or pinched at any point. Secure the wire harness so that the Tour-Pak can move freely. 5
6 STEP 10 To secure the Tour-Pak in place, turn all 4 locks (PIC 7 on Page 3) until snug and rotate the levers up until they lock in place. You should not need to use any type of tool for leverage to tighten the levers sufficiently. You should be able to feel the lever snap into place when folded over. If you do not feel a positive snap when folding the lever, it may be too tight. Loosen 1/2 turn and fold over again. Test that the Tour-Pak is secure before using the motorcycle. Before each ride inspect to ensure the levers are folded over in place and that the Tour-Pak is secure. '97-'08 Touring Models with Detachable Tour-Pak Open the Tour-Pak and remove the liner. Remove the hardware securing the Tour-Pak to the support bracket - save this hardware, it will be re-used. Remove the Tour-Pak from the support bracket and (if possible) put the Tour-Pak on a covered workbench. If installing on the bike, rotate the Tour-Pak forward, resting it where the seat would be. Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket. Place the base plate over the support bracket. Line up the holes in the base plate with the holes in the support bracket and secure using the stock hardware removed in Step 2 through the base plate and in to the support bracket. Tighten the hardware. For bikes with the injected molded Tour-Paks - Follow Steps 4-10 in the "for '06-'08 Touring models" section above For bikes with the fiberglass Tour-Paks - Follow Steps 4-10 in the "for '97-'05 Touring models" section above Tighten all hardware and make sure the Tour-Pak is secure before operating the motorcycle. Before each ride inspect to ensure the levers are folded over in place and that the Tour-Pak is secure. Ride On! 6
INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1
INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #1002493 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C3 02/2014 www.jettools.com
More informationFSCTD Dual Back to Back Flat Screen Ceiling Mount
Page 1 of 6 FSCTD Dual Back to Back Flat Screen Ceiling Mount The FSCTD Dual Back to Back Flat Screen Ceiling Mount is designed to suspend a monitor from a single flange mounted to structure in the ceiling.
More informationQUICK DETACH BACKREST KIT HARLEY-DAVIDSON FL TOURING MODELS (EXCEPT FLHTC/I & FLHTCUI) PARTS INCLUDED
PARTS INCLUDED 1 - Backrest Assembly 1 - Right Side Bracket Assembly 1 - Left Side Bracket Assembly 1 - Adapter Bracket, Left 1 - Adapter Bracket, Right 6-3/8 x1/8 Mounting Spacer 2-1/4 x1/8 Mounting Spacer
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T81 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationPlease Do Not Return This Product To The Store!
MODEL NO. T8176 QUICK SERVE 3000 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013
More informationInstallation Instructions Hinged Roof Rack
Installation Instructions Hinged Roof Rack Application: Jeep Wrangler Unlimited 2004 - Current Part Number: 41435-01 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationINSTALLATION INSTRUCTIONS Lateral Shift Accessory Model: PAC-800
INSTALLATION INSTRUCTIONS Lateral Shift Accessory Model: PAC-800 The PAC-800 Lateral Shift Accessory is for use with Chief Model PSM, PST, PRO, PLP, Large Flat Panel Display wall mounts. It can be installed
More informationATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.
INSTALLATION MANUAL Models 96111-3-02 & 96511-3-02 Bulkheads for 2014 and Later Ford Transit Connect Vans ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING
More informationInstallation Instructions HighRock 4x4 TM
Installation Instructions HighRock 4x4 TM Slider Step Vehicle Application: Jeep CJ Wrangler 1976 1986 Part Number: 49311 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationLC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60
More informationHollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide
Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: End User: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating
More informationVAN STORAGE SOLUTIONS FOR THE WAY YOU WORK
WWW.WEATHERGUARD.COM VAN STORAGE SOLUTIONS FOR THE WAY YOU WORK Weather Guard / KNAACK 420 E. Terra Cotta Ave. Crystal Lake, IL 60014 USA 800-456-7865 (Toll Free) 800-334-2981 (Fax) Knaack.OrderEntry@wernerco,.com
More informationOwner s Manual GS2010 Garden Seeder/Fertilizer. Caution: Carefully read all Rules and Instructions for Safe Operation.
Manufacture s Limited Warranty for The limited warranty set forth below is given by Precision Products, Incorporated with respect to new merchandise purchased and used in the United States, its possessions
More informationTilting, Swiveling & Rotating Flat Panel Wall Mount
Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical
More informationINSTALLATION INSTRUCTIONS Scout II - Fast Trac PART #
INSTALLATION INSTRUCTIONS Scout II - Fast Trac PART #442-210 Thank you for purchasing Specialty s Convertible Top for your Scout vehicle. It has been designed for great fit and long wear. Please read and
More informationMedium Flat Panel Dual Swing Arm Wall Mount JWD-V
INSTALLATION Medium Flat Panel Dual Swing Arm Wall Mount The single swing arm wall mount is designed for mounting a medium sized flat panel display. The can swing out from, or fold against, the wall depending
More informationLC200C9F Ceiling Mount for up to 32" Flat Panel Screens with 200mm x 200mm VESA Mounting Patterns
Page 1 of 6 LC200C9F Ceiling Mount for up to 32" Flat Panel Screens with 200mm x 200mm VESA Mounting Patterns The LC200C9F Flat Screen Ceiling Mount is designed to suspend a monitor from a round flange
More informationOWNER'S MANUAL. Please Do Not Return This Product To The Store!
MODEL NO. T8190SA TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationModels 2230 and 2240
Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform
More informationLC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
LC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns Multi-position triple pivoting arms allows you to position the monitor
More informationLC200WT Security Wall Mount with Tilt for up to 32" Flat Screens
Page 1 of 6 The LC200WT Security Wall Mount with Tilt is designed to secure up to a 32" flat panel monitor to the wall while still allowing the monitor to tilt. The VESA mounting patterns on the front
More informationSignature Choral Riser Side Rail
Assembly/Owner s Manual Signature Choral Riser Side Rail Signature Choral 3-Step Riser with Optional Side Rail Signature Choral 4-Step Riser with Optional Side Rail CONTENTS Visit the Signature Choral
More informationLC6X4WTM Security Wall Mount with Tilt for up to 60" Flat Screens with VESA 600mm x 400mm or less
Page 1 of 6 The LC6X4WTM Security Wall Mount with Tilt is designed to secure a flat screen, up to a 60", to the wall while still allowing the monitor to tilt. The VESA mounting patterns on the front of
More informationFoot Rail. Nissan Navara_Frontier D23 DC START HERE! READ ME FIRST
Foot Rail Nissan Navara_Frontier D3 DC ENG FANN00 START HERE! READ ME FIRST Don t be a hero and muscle through this without first reading these fitting instructions! Improper installation of this gear
More informationTilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM
Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /
More informationINSTALLATION INSTRUCTIONS
CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone:
More informationOWNER'S MANUAL JST-48 Sliding Table
OWNER'S MANUAL JST-48 Sliding Table (shown mounted on JET 708663PK) JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000 A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840 www.jettools.com
More informationSpeaker Mount Center Channel Speaker Adapter (PAC-301)
I N S T R U C T I O N M A N U A L Speaker Mount Center Channel Speaker Adapter () The Speaker Mount Center Channel Speaker Adapter () uses the same interface as the Side Speaker Adapter and can be used
More informationDRAWER Mitsubishi pajero lwb
DRAWER Mitsubishi pajero lwb SSDS601 / SSMP001 INSTALL TIME: 45 mins Thank you for purchasing a Front Runner Storage System. This Storage System is made up of the following components: 1. A Drawer System
More informationOperating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table
Operating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-140780 Ph.: 800-274-6848 Revision B1 05/2014 www.jettools.com Copyright
More informationTilting Flat Panel Wall Mount Installation Guide
Tilting Flat Panel Wall Mount Installation Guide Model: A580TM Easy installation Built-in level for easy positioning Safety bolts lock the TV on the mount Easy to adjust tilt angles: +5 to -15 degrees
More informationP4263TP. Installation Guide. Low-Profile Tilting Portrait Mount for Flat-Panels
Low-Profile Tilting Portrait Mount for Flat-Panels 1321 S. State College Blvd., Fullerton, CA 92831 USA Weight Limit Maximum Flat Panel Weight: 175 lbs. Warning Statements THE WALL STRUCTURE MUST BE CAPABLE
More informationHERCULES EXTENDED TOWER
AmeriGlide Accessibility Solutions HERCULES EXTENDED TOWER ATION GUIDE Please read this installation guide carefully to ensure correct installation of the HERCULES EXTENDED TOWER Vertical Platform Lift.
More informationInstallation Manual Roof Zone Ladder Rack
Installation Manual Roof Zone Ladder Rack 102113,E1346 Installation Time: About 90 minutes. Depending on truck and Do-it-Yourself experience level Tools Required: Electric Drill with 1/2 Chuck 1/2 & 7/32
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationInstallation Instructions Lower Cargo Rack Bracket
Installation Instructions Lower Cargo Rack Application: Jeep Wrangler 2003 Current Part Number: 41437 US Patent 6799706 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationINSTALLATION & OPERATING INSTRUCTIONS. REDCO LETTUCE KING I and LETTUCE KING IV
INSTALLATION & OPERATING INSTRUCTIONS for REDCO LETTUCE KING I and LETTUCE KING IV Lettuce King I Shown with optional Drum Ring Lettuce King IV TO BE SERVICED ONLY BY AUTHORIZED PERSONS P/N: 2802381 REV:
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationCheck us out on-line! Installation Instructions
Installation Instructions 2 OPTIONAL ACCESSORIES Order Quantum Rack Accessories Online at www.dawsbetterbuilt.com Cargo Lock Kit Secure Your Load Cargo Locks can easily be installed and adjusted left or
More informationModel 6360/6361. Ambulance Cot Fastener INSTALLATION/OPERATION INSTRUCTIONS. IMPORTANT Keep manual on file at all times.
IMPORTANT Keep manual on file at all times. Model 6360/6361 Ambulance Cot Fastener INSTALLATION/OPERATION INSTRUCTIONS For Parts or Technical Assistance 1 800 784 4336 Table of Contents Introduction..............................................................................
More informationAll Purpose Hardware
Backs and Support OWNER MANUAL All Purpose Hardware TFB Hardware All Purpose (Knob) Owner s Manual Customer Satisfaction 1.0 Stealth Products strives for 100% customer satisfaction. Your complete satisfaction
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8266
More informationFreshSesh, PowderHound & Big PowderHound
FreshSesh, PowderHound & Big PowderHound Carrier (2x) universal mounting bracket (4x) SkiLift (2x) (mounting bracket parts:) Hex Key with Bolt (2x) SkiLift (2x) Button Head Screw (2x) Hex Wrench (1x) Base
More informationPlease read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.
Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2
More informationInstallation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays
Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502
More informationMortising Attachment
Mortising Attachment Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationLAnd Rover defender TDI & TD5 Gullwing WINDOW Box. You will need to have installed a Gullwing Door before installing the Window Box.
LAnd Rover defender TDI & TD5 Gullwing WINDOW Box GWLD008 INSTALL TIME: 2 Hours You will need to have installed a Gullwing Door before installing the Window Box. IMPORTANT WARNING! IT IS CRITICAL THAT
More informationModel Assembly & Operating Instructions
30 SHEAR BRAKE ROLL Model 05907 Assembly & Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationINSTALLATION MANUAL PBC-UMS
INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation
More informationRZR 4 Doors Part # Polaris RZR XP & Turbo ( ) Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com RZR 4 Doors Part # 07-1802 Polaris RZR XP 4 1000 & Turbo (2015-2018) Black Revision No: 01 Revision Date:
More informationInstallation Instructions
Installation Instructions Sure Step (Part # DN260-S4B/ DN260-S4S Part # DN270-S4B/ DN270-S4S) 2009-2010 Dodge Ram1500 Crew Cab & Quad Cab 2010 Ram 2500/3500 Crew Cab For Technical Support/Warranty Information
More informationManual Carton Closing Staplers
Operator s Manual Manual Carton Closing Staplers SHB00-A Item No. 6400 -/8" Crown Carton Closing Stapler 5/8" and /4" (5mm and 8mm) Ask for Genuine INTERCHANGE A58 and A4 Staples SHB50-C Item No. 640 -/4"
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationContinuous Handrail Kit Installation Instructions
Continuous Handrail Kit Installation Instructions ALUMINUM RAILING SYSTEM Canadian Version Wall Application (see page 2) Railing Application (see page 7) Wall anchors not provided Hardware included: 1x
More informationINSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION
INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters
More informationINSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320
INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationQuick Release Hardware
Backs and Support OWNER MANUAL Quick Release Hardware TFB Hardware Quick Release Owner s Manual Customer Satisfaction 1.0 Stealth Products strives for 100% customer satisfaction. Your complete satisfaction
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationModels 2130 and 2140
Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Perform the following sequence
More informationATV STORM CHASER PLOW PUSH TUBE KIT
ATV STORM CHASER PLOW PUSH TUBE KIT P/N 33-0070 OWNER S MANUAL Application MID-BODY ATV MOUNT NO. 15-XXXX, ALL MOUNT NO. 15-0050 ATTENTION DEALER: CUSTOMER MUST RECEIVE A COPY OF THIS MANUAL AT THE TIME
More informationw w w. h d o n l i n e s h o p. d e VRSCF RIGID SADDLEBAGS GENERAL PREPARATION -J04704 REV Kit Number Models Tools and Supplies Required
-J070 REV. 00-0- VRSCF RIGID SADDLEBAGS GENERAL Kit Number 7-0 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationINSTRUCTION SHEET STRUT DRIVER RETROFIT KIT PN: 22-79SDRF
INSTRUCTION SHEET STRUT DRIVER RETROFIT KIT PN: 22-79SDRF COMPONENTS: - Note: Each kit comes with one Strut Driver Gear Case Assembly, one Strut Driver Tube End Adapter Assembly, and a One-Time-Use Threadlocker
More informationATV SNOW PLOW 50 IN. UNIVERSAL SYSTEM OPERATOR S MANUAL MODEL NUMBER
OPERATOR S MANUAL warranty_badges.pdf 8/8/ 0: AM 0 IN. UNIVERSAL ATV SNOW PLOW SYSTEM MODEL NUMBER 0098 SAVE THESE INSTRUCTIONS Important safety instructions are included in this manual. MADE IN USA REV
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm Model: AM300/AM300-B NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations
More informationM ACS Instructions
APPLICABLE MODELS: Nissan Frontier 2005 and up short bed with Utili-Trak mounting rails PACKAGE CONTENTS 00-0060-M-01-1205 ACS Instructions Leitner Designs 25675 Taladro Circle Unit E Mission Viejo, CA
More informationOwner s Manual ODYSSEY BENCH MODEL. O4100B shown REV E. Southern Avenue, Phoenix, AZ USA Workhorseproducts.
Owner s Manual ODYSSEY BENCH MODEL O4100B shown 67-1375 REV 218 3730 E. Southern Avenue, Phoenix, AZ 85040 USA 800-778-8779 Workhorseproducts.com 1 Table of Contents I. Introduction & Safety Information.
More informationPLOW MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL
PLOW MOUNT KIT FOR POLARIS RANGER P/N 34-3010 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be sure all parts
More informationLoading Dock Safety Gate
Installation Instructions/Operation and Maintenance Manual Models LDSG-120-PCY LDSG-144-PCY Table of Contents Product Information...2 Parts List...3 Installation Instructions...5 Operation...13 Inspection
More informationINSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X
INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X Thank you for purchasing Specialty s Convertible Top for your Jeep vehicle. It has been designed for great fit and long wear. Please
More informationInstallation Instructions Cage Kit JK Unlimited (4-Dr) Part # 76902
Please read instructions entirely before installing this product. Drilling is required to install this part. Parts Included Qty Parts Included Qty Driver Front Upright 1 Pass Side Drill Template (7289)
More informationModels 2030 and 2040
Models 2030 and 2040 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-8 Installation... 9 Operation... 9 Maintenance... 10 Accessories... 10 Limited Warranty... 10 Document # 101290 0607 Printed
More informationINSTALLATION INSTRUCTIONS Super Scout PART #
INSTALLATION INSTRUCTIONS Super Scout 71-80 PART #443-010 Thank you for purchasing Specialty s Convertible Top for your Scout vehicle. It has been designed for great fit and long wear. Please read and
More informationOwner s Manual LSP38 38 Lawn Sweeper
Owner s Manual LSP38 38 Lawn Sweeper Manual Contents Safety Instructions Assembly Operation Maintenance Parts Warranty 2 4-13 2 11 14-15 16 Your Lawn Sweeper Congratulations on your purchase of a new Precision
More informationInstruction Manual. LSV36108A 3600# Vertical Lift LAKESHORE PRODUCTS, INC.
LAKESHORE PRODUCTS, INC. Quincy. MI. 49082. tel 517.639.3815 LSV36108A 3600# Vertical Lift Instruction Manual Read carefully. Failure to follow the instructions and safety rules could result in severe
More information31082 INSTALLATION INSTRUCTIONS
08 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 07-CURRENT MAKE: HONDA MODEL: RIDGELINE STYLE: TRUCK WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationArticulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series)
P Articulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series) Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More informationBefore beginning refer to page 4 to assure that all parts are included in your kit. Refer to diagrams for help when installing top and hardware.
INSTALLATION INSTRUCTIONS BRONCO 1980-1994 PART #98501 RAMPAGE P R O D U C T S Thank you for purchasing Rampage Products Top for your Bronco. Please read and follow, precisely, all installation instructions
More informationTABLE MKI small with Basin and under rack brackets kit
TABLE MKI small with Basin and under rack brackets kit TBRA024 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO
More informationNOVA-EXT Versatile Projector Mount Model: NOVA-EXT
INSTALLATION MANUAL NOVA-EXT Versatile Projector Mount Model: NOVA-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 800-368-9700 Fax: 800-832-4888 Other Locations
More informationInstallation Instructions Factory Style Bow Kit
INSTALLATION TIME Installation Instructions Factory Style Bow Kit SKILL LEVEL Vehicle Application: Jeep Wrangler JK 2 Door 2007 Current Part Number: 55000 Compatible with original equipment soft tops,
More informationBOUNCE TABLE TENNIS TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS
BOUNCE TABLE TENNIS TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS NG2325 THANK YOU! Thank you for your purchase of our product. We work around the clock and around the globe to ensure that our products maintain
More informationtable brackets for mki table incl latch TBRA020
table brackets for mki table incl latch TBRA020 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER
More informationRPR-265. Power Rack (Cage)
ASSEMBLY INSTRUCTIONS 3 3/4" RPR-5 50 3/4" 51 1/4" Power Rack (Cage) TuffStuff Fitness Equipment, Inc. 15 E. Franklin Avenue Pomona, CA 9166, USA Ph: 909-6-1600 Fax: 909-6-496 E-mail: service@tuffstuff.net
More informationInstallation, Maintenance & Parts Manual
Installation, Maintenance & Parts Manual Multi Tier Aluminum Support Stands Table of Contents WARNINGS General Safety..................... 2 Introduction................................ 3 Product Description..........................
More informationCheckMate Lawn Striping Kit For Honda HRR Installation Guide
1161 E. Clark Road, Suite #220 DeWitt, MI 48820 800.411.0150 www.bigleaguelawns.com CheckMate Lawn Striping Kit For Honda HRR Installation Guide Important Big League Lawns, LLC warrants their products
More informationMODEL M1023 QUICK CHANGE COLLET ATTACHMENT INSTRUCTION MANUAL. Phone: On-Line Technical Support:
MODEL M1023 QUICK CHANGE COLLET ATTACHMENT INSTRUCTION MANUAL Phone: 1-360-734-3482 On-Line Technical Support: tech-support@shopfox.biz #6727BL COPYRIGHT JANUARY, 2005 BY WOODSTOCK INTERNATIONAL, INC.
More informationIF YOU DO NOT KNOW WHAT YOU ARE DOING, DO NOT DO IT!
TWIN CAM Alpha & Beta Case Boring Tool The JIMS Twin Cam Case Boring Tool takes all the guess work out of boring Twin Cam engine cases to accept JIMS 4" bore cylinders, 100 big bore kit, and 113" and 116"
More informationCRITICAL INFORMATION:
IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut
More informationPlease Do Not Return This Product to the Store!
MODEL NO. B400W GS60 BASKETBALL SYSTEM O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be
More informationPage 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged
More informationSunset Swings By Health in Motion, LLC
Sunset Swings By Health in Motion, LLC Model 421 Lounge Swing Assembly and Operation Manual Record Serial Number Here www.sunsetswings.com by Health In Motion, LLC. 11/6/2009 421 Owners Assembly and Operation
More informationREAD CAREFULLY - FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY RULES MAY RESULT IN SERIOUS INJURY
Owner s Manual LSV50120B LS5000B leg bundle LS5021B post bundle LS5022B cradle bundle V50120B straight LS5003B spreader bundle LS5004B bunk bundle LS4005B accessory box LS2005B wheel LS5007B diag bundle
More information