FCC COMPLIANCE REPORT

Transcription

1 Page 1 of 20 FCC COMPLIANCE REPORT Applicant: Address: Manufacturer: Address: E.U.T: Model Number: DONG GUAN SHI JIE HUA XU ELECTRONICS FACTORY NO 1SHI TANG BEI ST 2 SHI JIE TOWN DONGGUAN CITY GUANG DONG DONG GUAN SHI JIE HUA XU ELECTRONICS FACTORY NO 1SHI TANG BEI ST 2 SHI JIE TOWN DONGGUAN CITY GUANG DONG AC/AC ADAPTOR;AC/DCADAPTOR GPU XX XXX XXXX X X X X 1. where XX = Size of adaptor (EI48) 2. where XXX = Output Voltage- First 2 digits will be the whole value of the voltage and the last digit is the value of the decimal. 12 (12V) 125 (12.5V) 060 (6V)- Voltage range -3.0V-24.0V 3. where XXXX= Output Current. Current range. 500ma-4000ma 4. where X = Type of plug in,w (wall plug),c (desktop),g(groundpin) 5. where X = Type of plug in,w (wall plug),c (desktop),g(groundpin) 6. where X = Special function of adaptor- O (adaptor) X (special) where X = Unregulated/Regulated- O (unregulated) R (Regulated) Trade Name: -- Serial No.: -- Date of Receipt: Apr. 02, 2015 Date of Test: Apr , 2015 Test Specification: Test Result: Issue Date: FCC Part 15 Subpart B Class B: Oct ANSI C63.4:2009 The equipment under test was found to be compliance with the requirements of the standards applied. Apr. 07, 2015 Prepared by: Tested by: Approved by: Barrett/ Assistant Frank/ Engineer Allen/ Manager Other Aspects: None. Abbreviations: OK/P=passed fail/f=failed n.a/n=not applicable E.U.T=equipment under tested This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of

2 Page 2 of 20 TABLE OF CONTENTS Test Report Declaration 1.GENERALPRODUCTINFORMATION Product Function Description of Device (EUT) Difference between Model Numbers Independent Operation Modes TESTSTANDARDSANDSITES Description of Standards and Results List of Test and Measurement Instruments For radiated emission test TESTSET-UPANDOPERATIONMODES Principle of Configuration Selection Block Diagram of Test Set-up Test Operation Mode and Test Software Special Accessories and Auxiliary Equipment Countermeasures to Achieve EMC Compliance EMISSIONTESTRESULTS Conducted Emission at The Mains Terminals Test Radiated Emission Test PHOTOGRAPHS TESTING Photo of Conducted Measurement Photo of Radiated Measurement PHOTOGRAPHS OFTHEEUT...11 Page

3 Page 3 of GENERAL PRODUCT INFORMATION 1.1.Product Function Refer to Technical Construction Form and User Manual. 1.2.Description of Device (EUT) Description : AC/AC ADAPTOR;AC/DC ADAPTOR M/N : GPU WD00;GPU WA00 System Input Voltage : AC 120V/60Hz Rated Power : 28W Rated Output Voltage : AC 3-24V;DC 3-24V Rated Output Current : 500mA-4000mA DC Line : Unshielded,Undetachable 0.5m 1.3.Difference between Model Numbers None 1.4.Independent Operation Modes The basic operation modes are: Full Load Half Load Empty Load

4 Page 4 of 20 below. 2. TEST STANDARDS AND SITES 2.1.Description of Standards and Results The EUT have been tested according to the applicable standards as referenced Description of Test Item Power Line Conducted Emission Test Radiated Emission Test EMISSION Standard Limits Results FCC Part 15: 2009 ANSI C63.4: 2009 FCC Part 15: 2009 ANSI C63.4: 2009 Class B Class B PASS PASS 2.2.List of Test and Measurement Instruments For conducted emission at the mains terminals test Equipment Manufacturer Model No. Serial No. Last Cal. Next Cal. EMI Test Receiver Rohde & Schwarz ESHS Mar.16,15 1 Year 3 Artificial Mains Network Rohde & Schwarz ENV Mar.16,15 1 Year For radiated emission test Equipment Manufacturer Model No. Serial No. Last Cal. Next Cal. EMI Test Receiver Rohde & Schwarz ESR Mar.16,15 1 Year Bilog Antenna Schwarzbeck VULB 743 Mar.16,15 1 Year 9163 Signal Amplifier HP 8447D 1726A Mar.16,15 1 Year

5 Page 5 of TEST SET-UP AND OPERATION MODES 3.1.Principle of Configuration Selection Emission: The equipment under test (EUT) was configured to measure its highest possible radiation level. The test modes were adapted accordingly in reference to the Operating Instructions. 3.2.Block Diagram of Test Set-up System Diagram of Connections Between EUT and Simulators AC Mains EUT Dummy Load (EUT : AC/AC ADAPTOR;AC/DC ADAPTOR) 3.3.Test Operation Mode and Test Software Refer to Test Setup in clause 4 & Special Accessories and Auxiliary Equipment None. 3.5.Countermeasures to Achieve EMC Compliance None.

6 Page 6 of EMISSION TEST RESULTS 4.1.Conducted Emission at The Mains Terminals Test RESULT : Pass Test procedure : ANSI C63.4:2009 Frequency : 0.15~30MHz range Test Site : Shielded Room Limits : FCC Part 15 part B Class B: Oct Test Setup Date of test : Apr. 03, 2015 Model No. : GPU WD00;GPU WA00 Input Voltage : AC 120V/60Hz Operation Mode : Full Load The frequency range from 150 khz to 30 MHz was investigated. The bandwidth of the test receiver was set at 9 khz. The test data of the worst case condition(s) was reported on the following page. PC System Receiver >80cm LISN 80cm EUT 80cm Note: Test uncertainty: ±2.33dB at a level of confidence of 95%.

7 Page 7 of 20 Test Data M/N Mode Not : GPU WD00 : Full Load : All Test Values Greater Than 10dB Margin

8 Page 8 of 20 M/N Mode Not : GPU WD00 : Full Load : All Test Values Greater Than 10dB Margin

9 Page 9 of 20 M/N Mode Not : GPU WA00 : Full Load : All Test Values Greater Than 10dB Margin

10 Page 10 of 20 M/N Mode Not : GPU WA00 : Full Load : All Test Values Greater Than 10dB Margin

11 Page 11 of Radiated Emission Test RESULT Test procedure Frequency range Test Site : Pass : ANSI C63.4:2009 : 30~1000MHz : 966 Chamber Limits : FCC Part 15 part B Class B: Oct Test Setup Date of test : Apr. 03, 2015 Model No. Input Voltage : GPU WD00;GPU WA00 : 120V/60Hz Operation Mode : Full Load The EUT was placed on a turn table which was 0.8 m above the ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was set 10 m away from the receiving antenna which was mounted on an antenna tower. The measuring antenna moved up and down to find out the maximum emission level. It moved from 1 m to 4 m for both horizontal and vertical polarizations. The EUT was tested in the Chamber Site. It was pre-scanned with a Peak detector from the spectrum, and all the final readings from the test receiver were measured with the Quasi-Peak detector. The bandwidth setting on the test receiver was 120 khz. Semi-anechoic Chamber ANTENNA ELEVATION VARIES FROM 1 TO 4 METERS 3m EUT and Support System 1.5m(L)*1.0m(W)*0.8m(H) TURN TABLE (FIBRE GLASS) Receiver Note:Test uncertainty: ±2.86dB at a level of confidence of 95%

12 Page 12 of 20 Test Data M/N Mode Not : GPU WD00 : Full Load : All Test Values Greater Than 10dB Margin

13 Page 13 of 20 M/N Mode Not : GPU WD00 : Full Load : All Test Values Greater Than 10dB Margin

14 Page 14 of 20 M/N Mode Not : GPU WA00 : Full Load : All Test Values Greater Than 10dB Margin

15 Page 15 of 20 M/N Mode Not : GPU WA00 : Full Load : All Test Values Greater Than 10dB Margin

16 Page 16 of PHOTOGRAPHS TESTING 5.1.Photo of Conducted Measurement

17 Page 17 of Photo of Radiated Measurement

18 Page 18 of PHOTOGRAPHS OF THE EUT Figure General Appearance of the EUT Figure General Appearance of the EUT

19 Figure Inside View of the EUT M/N:GPU WD00 Page 19 of 20 Figure Inside View of the EUT M/N: GPU WD00

20 Figure Inside View of the EUT M/N:GPU WA00 Page 20 of 20 Figure Inside View of the EUT M/N:GPU WA00