Scroller power supply

Transcription

1 Scroller power supply with optional Wireless DMX Instruction Manual Models: WPSU-600/480/240 version 1.0 since 10 October 2018 DDL4 ATTENTION! This instruction manual contains important information about the installation and the use of the equipment. Please read and follow these instructions carefully. Always ensure that the power to the equipment is disconnected before opening the equipment or commencing any maintenance work. WPSU_en_manual_M198 ( 1 / 12)

2 IMPORTANT SAFETY INFORMATION The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings in this manual violates safety standards of design, manufacture, and intended use of this equipment. Do not operate in an explosive atmosphere! Do not operate this equipment in the presence of flammable gases or fumes. Operation of any electrical instrument in such an environment constitutes a definite safety hazard. Device should never be placed near or over heat register or any other source of heated air and it should not be installed or operated without proper ventilation. Mains AC V connection AC power is connected to the scroller via Neutrik PowerCon blue connector. Standard supply is UNISCHUKO lead with Neutrik PowerCon. Always respect markup of L and N on connector for correct wiring of Line and Neutral. DMX connection DMX connectors are located on left front side of the Scroller power supply. There are both 3-pin and 5-pin Neutrik fitted in. Last WPSU in line should be terminated by the termination resistor of 120ohm operated by switch close to the DMX IN/OUT. There is DATA LED indication for DMX data presence on the device. When operating device is in Wireless DMX mode, the loss of radio signal will cause the device switch automatically to the cable mode; the cable can be used as a backup of Wireless DMX line. Received Wireless DMX signal is not present on the DMX IN/OUT connectors at all times. Pin 1 Data Common Pin 2 Data - Pin 3 Data + ( 2 / 12)

3 Front panel: WPSU600: WPSU480: WPSU240: On the front panel, there is a red POWER indication LED for the power supply state. There is also a DATA LED for DATA indication. DATA LED is ON, when the DMX signal is connected to the device or it is received by the Wireless DMX. Wireless DMX is operated separately from the W-DMX module. Top button is the MODE button and is used for ON/OFF operation of the wireless part. Bottom W-DMX button is used for operation as Link/Unlink from the Wireless DMX transmitter. ( 3 / 12)

4 Rear panel: The MAINS fuse and MAINS connector /Neutrik PowerCon/ are located on the rear side of WPSU. On both long sides of device, there are 4 holes for M6 Eyebolt and 2 holes M10 for C-CLAMP attachment. ( 4 / 12)

5 Device in use: By default, Power LED indicates whether the device is on main power. If the Power LED does not come up, please check mains power input or fuse. Always use fuses of the same rating as the one received from manufacturer or one of rating written on backside. When the DMX cable is connected to the device, LED marked DATA goes ON; this indicates that WPSU is receiving the DMX signal. DATA LED indicates the ON state of Termination during the Power On sequence. To avoid misunderstanding between DATA and Termination indication, do not terminate the device without DMX data. Once the DMX signal is received, the terminal indication will be overridden by DMX DATA. The speed of light on these LEDs also indicates the refresh rate of DMX signal. DATA LED fast blinking stands for high refresh rate, while slow blinking means slow refresh rate. Scroller connection: Use only approved scroller cable. Approved cable should have two conductors of 14 AWG wire for power and two shielded and twisted conductors of 22 AWG wire for data. The following pinout for the 4-pin connector must be followed: PIN1: DC_GND PIN2: DATA- PIN3: DATA+ PIN4: DC+24V Optionally, unit can be equipped with DC12/36V/48V PSU Additional scrollers can be daisy-chained together from the OUT plug. Connect the last scroller to the return line of WPSU for termination and power supply. Compatible equipment watt consumption: Rosco I-Cue Rosco DMX Indexing Rotator AC Lighting/Apollo Chroma Q Broadway AC Lighting/Apollo Chroma Q M1, 2, 5, 8 Apollo Roto-Q City Theatrical DMX Iris DHA Gobo Carousel DHA Twin DMX Rainbow 6", 8", 12" Pro Colour Scroller Rainbow 15" Pro Colour Scroller Gam Indexable Twin Spin Gam SX-4, 6 Gobo Tray 17 watts 6 watts 22 watts 36 watts 12 watts 8.5 watts 18 watts 12 watts 14 watts 29 watts 14.4 watts 10.8 watts ( 5 / 12)

6 DMX only operation For the DMX operation, turn off the W- DMX module by holding the MODE button until both W-DMX and MODE buttons turn RED. Now connect the DMX cable to DMX-IN connector and use WPSU as standard DMX Scroller power supply. DMX+ Wireless DMX operation For W-DMX operation, turn ON the W-DMX module by holding the MODE button until the MODE button are lights GREEN. The W-DMX function button will indicate the W-DMX functionality as is shown in figure at the bottom of this page. W-DMX button has only one function; to log OFF from linked transmitter. To log off, hold for more than 5s. There is an automatic backup of W-DMX line by the cable connection. If the W- DMX is linked to transmitter and signal quality is bad, W-DMX active LED goes OFF and the splitter will retransmit signal from IN/TRHU port. In normal state, when W-DMX signal quality is good, the W-DMX active LED is ON. W-DMX LED/ button signalization: ( 6 / 12)

7 W-DMX functions 1. W-DMX is turned OFF. WPSU is used as a DMX splitter. To turn the W-DMX ON, hold the MODE button for three seconds. MODE button will light GREEN. 2. W-DMX is ready to be linked, WPSU works as s receiver of W-DMX signal without linking to the transmitter. Please hold the button on Transmitter to start linking to W-DMX transmitter. 3. W-DMX linked + DMX is missing on Transmitter the W-DMX LED is signalizing this by blinking in RED/GREEN state. Bar-graph is now in an active state. To link out from Transmitter, hold the W-DMX button for 10s; after that, module will be in state W-DMX is linked to Transmitter and receiving DMX signal. Both indicators are GREEN. Bar-graph is working and showing W-DMX signal strength. ( 7 / 12)

8 Technical data Mains power input: AC V / 50-60Hz, UniSchuko/PowerCon 3x0.75mm2, 1.5m long WPSU-240: 5A, WPSU-480: 8A, WPSU-600: 10A DMX Input / Output: 1x USITT DMX512 /RS485/ isolated up to 1000V Wireless DMX card made by or Scroller Output: 2,4,6 x USITT DMX512 /RS485 amplified DC24V power output* /DC48V version or others are on request/ Mounting points: In total, there are 4x M6 and 2xM10 for C-clamp and safety eye connection. Lightweight Aluminum with black/white powder coating: WPSU-240/480: 315x110x350mm 3.2/4kg WPSU-600: 383x110x350mm 5.3kg Temperature of use: -20 C to +40 C Warranty: Two-year /24-month/ warranty DECLARATION OF CONFORMITY According to guidelines 89/336 EEC and 92/31 EEC: Name of producer: SRS Light Design s.r.o. Address of producer: Rybnicna 36/D, SK Bratislava, Slovak Republic Declares that the product Name of product: WPSU, Scroller power supply Type: WPSU-240, WPS-480, WPSU-600, PSU-240, PSU-480, PSU-600 Corresponds to the following product specifications and R&TTE Directive of the European Union: Safety: EN60065, resp. EN EMC: EN , resp. EN Radio: EN ; ; EN ; EN ( 8 / 12)

9 ( 9 / 12)

10 ( 10 / 12)

11 ( 11 / 12)

12 Copyright 2018 SRS Group s.r.o. Specifications subject to change without notice. Document: WPSU_en_manual_M198 Version 1.0 Actual as of: 10 October 2018 SRS Group s.r.o. Rybnicna 36/D Bratislava Slovakia Phone: Fax: sales@srs-group.com ( 12 / 12)