New. Process Tools Selection Guide. Volume Washington Street Melrose, MA Phone Toll Free

Transcription

1 t Process Tools Selection Guide New Produc Volume 7 99 Washington Street Melrose, MA Phone Toll Free Visit us at

2 Honeywell Rotary owns a few units of Fluke 744 and Fluke 725. Our service personnel like the multifunction features of these calibrators, because a single unit allows them to handle various testing and calibration needs in the field. The products are robust and their accuracy meets or exceeds industry standards. Why choose Fluke? Mr. V. Rajagopal, Honeywell Rotary Pte Ltd, Singapore I ve been in the business for more than 20 years and I ve always had a Fluke multimeter. When it came time to buy a process calibrator, I knew the Fluke tool would be just as good as the multimeters. Now I use the 87 for troubleshooting and the 744 for calibrating process instruments at Bristol Myers Squibb. The Fluke product does everything I need it to do. Geoffrey Dell, Bristol Meyers Squibb, Evansville, IN I ve discovered the solution that works for me an all-in-one calibration unit from Fluke called the 744 Documenting Process Calibrator. It s literally saved me a zillion steps. I was carrying with me two, three maybe even four pieces of test equipment, plus my tools. Now, I just take the 744 that incorporates calibration and HART communication capability in a single, fast unit. It s the only way to go. Gene Guidry, Chevron Chemical, Port Arthur, TX 2

3 Application Assistance Application Assistance Process Tools Technical Notes and Application Notes can be obtained from processtools or by Fluke Fax in the United States at FlukeFax. Or contact your Fluke sales organization (in the United States call FLUKE). 1. Understanding Specifications for Process Calibrators (Literature Code , Fluke Fax #8024) Selection of a calibrator is often based on a specification sheet. This application note helps interpret and compare performance specifications typically used for process calibrators. 2. Transmitter Calibration (Literature Code , Fluke Fax #8507) Step-by-step instructions on how to calibrate analog temperature and pressure transmitters quickly and effectively using the Fluke- 740 series Documenting Process Calibrator. 3. HART Transmitter Calibration (Literature Code , Fluke Fax #8508) The need for calibration of HART smart transmitters is often misunderstood. What do you calibrate and when? Here is a step-by-step procedure showing how to use the Fluke 744 to perform calibration and digital adjustments of Rosemount 3051 and 3144 transmitters and other HART devices. 4. Limit Switches (Literature Code , Fluke Fax #8503) Verifying the exact temperature or pressure applied to a limit switch at its trip point can be hard to determine. Learn how the Fluke 740 Series Calibrators help solve this measurement problem. 5. Custom Units and User Entered Values (Literature Code , Fluke Fax #8502) This note demonstrates how to document local temperature indicators and pressure gauges in the field with a Fluke 740 Series Calibrator. 6. Pressure Calibration (Literature Code , Fluke Fax # 3024) Examples of how to calibrate, troubleshoot and verify the most common pressure devices and the Fluke tools that address these applications are shown. 7. Temperature Calibration (Literature Code , Fluke Fax #8509) Examples of how to calibrate, troubleshoot and verify the most common temperature devices and the Fluke tools that address these applications are shown. 8. NEW! Loop Calibration and Maintenance (Literature Code , Fluke Fax #3031) Loop calibrators are a versatile tool for maintaining 4-20 ma control loops. This note demonstrates how to use the Fluke 707, 787, 715 and 705 to perform several day-to-day tasks. 3

4 Process Tools Selection Guide Documenting MPC* Process Calibrators Pressure Calibrators T New Product Measure Model B 741B G G G G 724 See page V dc 30 V 300 V 300 V 300 V 30 V V ac (true-rms) 300 V 300 V 300 V Resistance 3200 Ω 11 kω 11 kω 11 kω 3200 Ω A dc 24 ma 110 ma 110 ma 110 ma 24 ma 24 ma 24 ma 24 ma 24 ma 4 A ac Frequency 10 khz 50 khz 50 khz 50 khz Pressure psig/ 30 psig/ 100 psig/ 30 psig/ 7 bar 2 2 bar 2 7 bar 2 2 bar 2 Temperature: RTDs 7 types 8 types 8 types 8 types 7 types Temperature: TCs 10 types 11 types 11 types 11 types 10 types Temperature: Infrared Capacitance Two Channel Connect-and-View Scope Power Measurement/Harmonics Analysis Source/Simulate V dc 10 V 15 V 15 V 15 V 10 V Resistance 3200 Ω 11 kω 11 kω 11 kω 3200 Ω ma dc/% scale 24 ma 22 ma 22 ma 22 ma ma source; auto step, auto ramp Frequency 10 khz 50 khz 50 khz 50 khz Temperature: RTDs 7 types 8 types 8 types 8 types 7 types Temperature: TCs 10 types 11 types 11 types 11 types 10 types Record Min Max Hold As Found/As Left Results Log Data Upload Data to PC Features 24 V Loop Supply Hart Communication Integrated Hand Pressure Pump Warranty 3 year 3 year 3 year 3 year 3 year 3 year 3 year 3 year 3 year Accessories 4 A/B C C C C A/B 1. Fluke 700 Pressure Modules required. See page Either the internal sensor or a Fluke 700 Pressure Module may be used; see page With accessory clamp

5 emperature Power Calibrators Loop Calibrators Digital Thermometers Quality Digital Multimeters New Product /53 52/51 43B mv 1000 V 10 V 28 V 28 V 600 V 1000 V 600 V 1000 V 600 V 1000 V 600 V 3200 Ω 40 MΩ 30 MΩ 40 MΩ 30 ma 24 ma 24 ma 24 ma 3 1 A 200 µa 1 A 10 A 3 20 khz 1000 khz 400 Hz 7 types 9 types 7 types J K T E K K 75 mv 10 V 3200 Ω 24 ma 24 ma 24 ma 24 ma 9 types 7 types 3 year 3 year 3 year 3 year 3 year 3 year 1 year 3 year 3 year 1 year Lifetime 3 year C C C C C C B B A/B C 4. A Compatible with LockPak; B Compatible with ToolPak; C Accepts hanging straps from ToolPak * Multifunction Process Calibrator 5

6 Multifunction Process Calibrator Fluke 725 Multifunction Process Calibrator. Simply Powerful. The Fluke 725 Multifunction Process Calibrator is a versatile, easy-to-use field calibrator. Use the measure and source functions to test and calibrate almost anything. Small, streamlined shape makes it easy to carry Rugged, reliable design stands up to field use Easy to read measure/ source screen lets you view input and output simultaneously Measure volts, ma, RTDs, thermocouples, frequency, and ohms to test sensors and transmitters Source/simulate volts, ma, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters Measure/source pressure using any of the Fluke 700Pxx Pressure Modules Source ma with simultaneous pressure measurement to conduct valve and I/P tests Support flow meter testing with frequency and counts per minute (CPM) functions Perform fast linearity tests with auto step and auto ramp features Power transmitters during test using loop supply with simultaneous ma measurement Store frequently-used test setups for later use Backlight lets you work in poor light Remote interface allows benchtop automated operations Large battery capacity of four AA cells Battery door for easy changes 6 Simultaneous Function Capability Channel A Channel B ma DC M M or S ma DC with 24 V loop supply M mv DC M or S V DC Measure M V DC Measure V DC Source M or S 3200 Ohms M or S Thermocouple J, K, T, E, R, S, B, L, U, N M or S RTD Ni120; Pt100 (3926); Pt100 (JIS); Pt100, 200, 500, 1000 (385) M or S Pressure (requires Fluke 700Pxx Modules) M M used as S Frequency; Squarewave, 1 CPM to10 khz; fixed amplitude 5 V p-p M or S M = Measure S = Source/Simulate Ordering information Fluke 725 Multifunction Process Calibrator Each calibrator includes: TL75 Test Leads, AC70 Test Clips, one pair of stackable test leads, 4 AA batteries; Product Overview Manuals in English, French, German, Spanish, Italian, Dutch, Norwegian, Danish, Swedish, Finnish, Portuguese, Korean, Chinese, and Japanese, Users Manuals on CD-ROM; NIST-traceable certificate of calibration; CE and CSA markings.

7 Summary specifications (18 C to 28 C for one year) Function Measure or Source Range Resolution Accuracy Notes Voltage 0 to 100 mv 0.01 mv.02 % Rdg + 2 LSD Max load, 1 ma 0 to 10 V (source) V 0 to 30 V (measure) V ma (on 724, measure only) 0 to ma.02 % Rdg + 2 LSD Max load, 1000 Ω mv (TC terminals) mv to mv.01 mv.025 % of range + 1 LSD Resistance 0 Ω to 3200 Ω (measure) 0.01 Ω to 0.1 Ω 0.10 Ω to 1.0 Ω 15 Ω to 3200 Ω (source) Frequency (source) 2.0 to CPM 0.1 CPM ±.05 % of setting For frequency source, (725 only) 1 to 1000 Hz 1 Hz ±.05 % of setting waveform is 5 V p-p 1.0 to 10.0 khz 0.1 khz ±.25 % of setting squarewave, -0.1 V offset Frequency (measure) 1 CPM to 10 khz 5 digits 0.05 % Rdg + 1 count 1 V p-p min. (725 only) Loop Supply 24 V dc N/A 10 % Temperature coefficient, -10 C to 18 C, 28 C to 55 C, ±.005 % of range per C. Thermocouple accuracy specifications (Fluke 724/725) Thermocouple Measure or Source J -200 to 0 C 1.0 C 0to1200 C 0.7 C K -200 to 0 C 1.2 C 0to1370 C 0.8 C T -200 to 0 C 1.0 C 0to400 C 0.8 C E -200 to 0 C 0.9 C 0to950 C 0.7 C R -20 to 0 C 2.5 C 0to500 C 1.8 C 500 to 1750 C 1.4 C S -20 to 0 C 2.5 C 0to500 C 1.8 C 500 to 1750 C 1.5 C B 600 to 800 C 2.2 C 800 to1000 C 1.8 C 1000 to 1800 C 1.4 C L -200 to 0 C 0.85 C 0to900 C 0.7 C U -200 to 0 C 1.1 C 0to400 C 0.75 C N -200 to 0 C 1.5 C 0to1300 C 0.9 C Resolution J, K, T, E, L, N, U 0.1 C, 0.1 F B, R, S 1 C, 1 F Notes Accuracy specifications include 0.2 C cold junction uncertainty. RTD ranges and accuracy specifications (Fluke 724/725) RTD Types, Ranges and Accuracies Measure (4 wire) Source Ni C to 260 C 0.2 C 0.2 C Pt C to 800 C 0.33 C 0.33 C Pt C to 630 C 0.3 C 0.3 C Pt (JIS) -200 C to 630 C 0.3 C 0.3 C Pt C to 250 C 0.2 C 0.2 C 250 C to 630 C 0.8 C 0.8 C Pt C to 500 C 0.3 C 0.3 C 500 C to 630 C 0.4 C 0.4 C Pt C to 100 C 0.2 C 0.2 C 100 C to 630 C 0.2 C 0.2 C Resolution RTD 0.1 C, 0.1 F General specifications for Fluke 724 and 725 calibrators Maximum voltage: 30 V Storage temperature: -20 C to 71 C Operating temperature: -10 C to 55 C Relative humidity: 90 % (10 C to 30 C); 75 % (30 C to 40 C); 45 % (40 C to 50 C); 35 % (50 C to 55 C) Shock: 30 g, 11ms, half-sine shock Vibration: Random, 2 g, Hz Safety: CSA C22.2 No :1992 EMC: EN :1992 and EN55022:1994 Class B Size/weight: 96 x 200 x 47 mm (3.8 x 7.9 x 1.9 inches) 650 g (23 oz) Battery: Four AA alkaline batteries. Battery life: 25 hours typical Warranty: Three years 7

8 Documenting Process Calibrators 741B/743B/744 Documenting Process Calibrators. Work smarter. Work faster. Whether you are calibrating instruments, troubleshooting a problem, or running planned maintenance, the multifunction Fluke 740 Series Documenting Process Calibrators help get the job done faster: Calibrate temperature, pressure, voltage, current, resistance, and frequency Measure and source with one compact, rugged, reliable tool Create and run automated as-found/as-left procedures to satisfy quality programs or regulations. Supports linear, square-root devices plus one-point and twopoint limit switches Record and document results Transfer the results to a PC (743 or 744), saving the time to manually transcribe data Run popular instrumentation management software New bonus software features, enabled with product registration Transmitter mode Bar code entry Ordering information 8 For more information Call today for your free 740 Series Brochure, Fluke 741B Documenting Process Calibrator Fluke 743B Documenting Process Calibrator Each calibrator includes TL24 Industrial Test Leads (2 sets), AC20 Test Clips (2 sets), TP20 Test Probes (1 set), BP7217 Battery Pack, BC7217 Battery Charger, Instruction Manual, NIST traceable calibration certificate and data, three-year warranty, serial port cable (743B only), DPC/TRACK Sample Version with free PC communication utility software (743B only). Fluke 744 Documenting Process Calibrator Each calibrator includes TL24 Industrial Test Leads (2 sets), AC20 Test Clips (2 sets), TP20 Test Probes (1 set), BP7235 NiMH Battery Pack, BC7217 Battery Charger, serial port cable, HART communications cable, DPC/TRACK Sample Version with free PC communication utility software, Instruction Manual, HART Users Manual, NIST-traceable calibration certificate and data, three-year warranty. 744 Upgrades Available Fluke periodically releases new internal software for the Fluke 744. These upgrades include: New revisions of previously supported instruments. Device-specific command support for new instruments. New HART communication capability.

9 Summary one year specifications Measure Source Range (full scale) Accuracy Range (full scale) Accuracy (% of reading+% of full scale) (% of reading+% of full scale) mv DC % % mv 0.01 % % V DC % % V 0.01 % % V DC % % V 0.01 % % V DC 0.05 % % V DC 0.05 % % V AC, 20 to 40 Hz 2 % + 10 counts V AC, 40 to 500 Hz 0.5 % + 5 V AC, 500 to 1 khz 2 % + 10 V AC, 1 khz to 5 khz 10 % ma DC 0.01 % % Source ma 0.01 % % ma DC 0.01 % % Simulate ma 0.02 % % Ω 0.05 % + 50 mω Ω 0.01 % + 20 mω Ω 0.05 % + 50 mω Ω 0.01 % + 40 mω kω 0.05 % Ω kω 0.02 % Ω kω 0.1 % + 10 Ω kω 0.03 % + 5 Ω 1.00 to Hz 0.05 Hz 0.00 to Hz 0.01 Hz to Hz 0.5 Hz to Hz 0.1 Hz to khz 5 Hz to Hz 0.1 Hz to khz 50 Hz to khz 2 Hz to khz 5 Hz For pressure specifications, see page 13. General specifications for Fluke 741, 743 and 744 calibrators Data log: Measure V, ma, ohms, frequency, temperature, pressure. One to 60 readings per minute, 8000 readings max Ramp: Source V, ma, frequency, temperature. Four steps/second; trip detect on continuity or voltage Loop power: Selectable, 24 V or 28 V; 22 ma max Environmental: 741/743 specifications apply from +18 C to +28 C Operating temperature: -10 C to 50 C (typical specs to -20 C) Pressure modules are totally compensated and specs apply 0 C to 50 C Storage temperature: -20 C to 60 C Safety: Complies with CAN/CSA C22.2 No , ANSI/ISA S , UL3111, and EN610-1: V, Over-voltage Category II Size/weight: 130 x 236 x 61 mm (5.1 x 9.3 x 2.4 in), weight 1.4 kg (3 lbs 1 oz) Battery: Internal battery pack NiCd, 7.2 V, 1700 mah; NiMH (744 only) 7.2 V, 3500 mah, typical usage, greater than 8 hours Warranty: Three years Temperature, RTDs and Thermocouples Measure Source Device Accuracy Accuracy 10 Ω Cu (427) 3 C 1 C 100 Ω Pt (3916) 0.3 C 0.1 C 100 Ω Pt (3926) 0.3 C 0.1 C 100 Ω Pt (385) 0.3 C 0.1 C 200 Ω Pt (385) 0.3 C 0.1 C 500 Ω Pt (385) 0.3 C 0.1 C 1000 Ω Pt (385) 0.3 C 0.1 C 120 Ω Ni (672) 0.3 C 0.1 C E 0.3 C 0.2 C N 0.5 C 0.3 C J 0.3 C 0.2 C L 0.3 C 0.2 C K 0.3 C 0.3 C T 0.3 C 0.3 C U 0.3 C 0.3 C B 0.9 C 0.8 C R 1.0 C 0.9 C S 0.9 C 0.9 C C 0.6 C 0.6 C Resolution: 0.1 C, except 1 C for 10 Ω Cu. Best case, mid-range accuracies. Sensor inaccuracies not included. For 2-wire and 3-wire RTD measurements, add 0.4 C. Thermocouple accuracies with external cold junction. For internal junction add 0.2 C. RTD source function: Supports fast pulsed transmitters and PLCs with pulse times as short as 1 ms. Maximum input current is 8 ma for 100 and 120 ohm RTDs. 9

10 Documenting Process Calibrators Get HART-ability The Fluke 744 offers all of the capabilities of the 743B, plus the ability to calibrate, maintain, and troubleshoot HART instrumentation with just one tool. This rugged, reliable tool offers: Integrated HART communication functions, permitting you to monitor, control, and calibrate HART instrumentation. Handling of fast pulsed RTD transmitters and PLCs, with pulses as short as 1 ms. NiMH battery with 3500 ma hour life and gas gauge. The 744 offers the most complete HART implementation of any process calibrator. The 744: Requires no external box or second tool for everyday HART calibration and maintenance. Offers fast HART communication. Supports popular models of HART transmitters, with more device-specific command support than any other HART field calibrator. Fully complies with the Data Link Layer of the HART protocol, supporting multiple masters, burst mode, and multi-drop configurations. Is easy to update as additional instruments and new HART versions are released. Is based on the 743B, the most rugged, reliable multifunction field calibrator available. Is backed by the service and support of the Fluke organization, a member of the HART Communications Foundation. Ordering information 10 Fluke 744 Documenting Process Calibrator Each calibrator includes TL24 Industrial Test Leads (2 sets), AC20 Test Clips (2 sets), TP20 Test Probes (1 set), BP7235 NiMH Battery Pack, BC7217 Battery Charger, serial port cable, HART communications cable, DPC/TRACK Sample Version with free PC communication utility software, Instruction Manual, HART Users Manual, NIST-traceable calibration certificate and data, three-year warranty. 744 Upgrades Available Fluke periodically releases new internal software for the Fluke 744. These upgrades include: New revisions of previously supported instruments. Device-specific command support for new instruments. New HART communication capability. The upgrade can be easily loaded from a PC to a 744. For details of the latest upgrade, see

11 With one powerful tool, you can: Generate precision electrical, temperature, or pres- by reading and writing Re-label smart transmitters sure signals for analog HART tag and message stimulus or sensor fields. simulation. Change HART temperature Simultaneously measure sensor configuration (e.g., electrical, temperature, TC to RTD). or pressure signals from Change HART temperature transmitter output. sensor wire configuration Interrogate HART devices (e.g., 2-wire to 4-wire). to determine type, manufacturer, model, and tag-id. ters by reading and storing Clone additional transmit- Read HART PV function, basic HART configurations. smart transmitter Perform automated HART digital output, while sensor trim and output trim measuring analog ma for selected devices. output. Perform loop test with Make field adjustments simultaneous analog and to ranging, damping, and digital ma readout. other top-level configuration settings by reading excitation smart transmit- Address new, fast, pulsed- and writing HART configuratioters and PLCs. functions. General specifications are identical to those of the 743B except: Loop power: Selectable, 24 V or 28 V; 22 ma max. On the 744 only, whenever Loop Power is enabled, a 250 ohm resistor is automatically inserted in series with the ma measure terminals. HART communications cable: Maximum input voltage, 30 V. Battery: BP7235, 3500 ma-hour NiMH Battery Pack. Versatile HART protocol support The 744 supports these classes of instructions: Universal commands provide functions that are implemented in all field devices, for example, read manufacturer and device type, read primary variable (PV), or read current output and percent of span Common practice commands provide functions that are common to many but not all field devices, for example read multiple variables, set damping time, or loop test Device-specific commands provide functions that are unique to a particular field device, for example sensor trim. The 744 supports popular devices from ABB, Endress + Hauser, Foxboro, Honeywell, Moore, Emerson Process Management (formerly Fisher- Rosemount), Siemens, SMAR, and Yokogawa. For more information on the HART protocol, see 11

12 700SW DPC/TRACK Software DPC/TRACK Software is a specialized database that can help you manage your instrumentation and address the documentation requirements of quality programs and regulations. With DPC/TRACK and a 702, 743 or 744 DPC you can: Manage your inventory of tags and instruments. Schedule tag IDs for calibration. Create tag specific procedures, including instruction on how to locate an instrument and how to safely isolate and connect. Load those procedures to your DPC. Select and execute automated as-found/as-left procedures in the field, automatically capturing the results data. Include comments as to Reasons for Work, Problems Found, and Actions taken (743 and 744 only). Unload your results to a PC. Print a selection of preformatted reports. Examine the calibration histories of your Tags and instruments. Import instrument data and procedures as ASCII text. Export instrument data, procedures, and results as ASCII text. DPC/TRACK operates in the same languages as the DPCs: English, French, German, Italian, and Spanish. A Pentium based machine is recommended. Fluke DPC/TRACK is an easy to use, single-user, entrylevel instrumentation manager. For more sophisticated software, you may wish to investigate products from Fluke s software partners: DocuMint AMS from Emerson Process Management, (formerly Fisher-Rosemount). On Time Support Ordering information Fluke 700SW DPC/TRACK Software Supports Fluke 702, 743 and 744 Documenting Process Calibrators and includes: Software CD-ROM, Instruction Manual, serial port cable, and DB9 to DB25 adapter. 12

13 700 Series Pressure Modules Fluke offers 29 Pressure Modules for the Fluke 741, 743, and 744 Documenting Process Calibrators, the Fluke 717 and 718 Pressure Calibrators, plus the 725 Multifunction Process Calibrator. Gage, differential, dual (compound), absolute and vacuum modules are available to cover virtually any pressure application. Rugged cases protect the modules from harsh conditions. Pressure Reference High Low Range/ Range (approx)/ uncertainty side side Fitting Model Resolution Resolution (23 ± 3 C) media media material Differential Fluke 700P00 1 in. H 2 O/ kpa/ % Dry Dry 316 SS Fluke 700P01 10 in. H 2 O/ kpa/ % Dry Dry 316 SS Fluke 700P02 1 psi/ Pa/ % Dry Dry 316 SS Fluke 700P22 1 psi/ Pa/ % 316 SS Dry 316 SS Fluke 700P03 5 psi/ kpa/ % Dry Dry 316 SS Fluke 700P23 5 psi/ kpa/ % 316 SS Dry 316 SS Fluke 700P04 15 psi/ kpa/ % Dry Dry 316 SS Fluke 700P24 15 psi/ kpa/ % 316 SS Dry 316 SS Gage Fluke 700P05 30 psi/ kpa/ % 316 SS N/A 316 SS Fluke 700P psi/ kpa/ % 316 SS N/A 316 SS Fluke 700P psi/ kpa/ % 316 SS N/A 316 SS Fluke 700P psi/ kpa/ % 316 SS N/A 316 SS Fluke 700P psi/ kpa/ % 316 SS N/A 316 SS Fluke 700P psi/ M Pa/ % 316 SS N/A 316 SS Absolute (not compatible with Fluke 701 or 702) Fluke 700PA3 5 psi/ kpa/ % 316 SS N/A 316 SS Fluke 700PA4 15 psi/ kpa/ % 316 SS N/A 316 SS Fluke 700PA5 30 psi/ kpa/ % 316 SS N/A 316 SS Fluke 700PA6 100 psi/ kpa/ % 316 SS N/A 316 SS Vacuum (not compatible with Fluke 701 or 702) Fluke 700PV3-5 psi/ kpa/ % 316 SS Dry 316 SS Fluke 700PV4-15 psi/ kpa/ % 316 SS Dry 316 SS Dual Fluke 700PD2 ±1 psi/ ±6900 Pa/ % 316 SS Dry 316 SS Fluke 700PD3 ±5 psi/ ±34 kpa/ % 316 SS Dry 316 SS Fluke 700PD4 ±15 psi/0.001 ±103 kpa/ % 316 SS Dry 316 SS Fluke 700PD5-15/30 psi/ /207 kpa/ % 316 SS N/A 316 SS Fluke 700PD6-15/100 psi/ /690 kpa/ % 316 SS N/A 316 SS Fluke 700PD7-15/200 psi/ /1380 kpa/ % 316 SS N/A 316 SS High Fluke 700P psi/ M Pa/ % C276 N/A C276 Fluke 700P psi/ M Pa/ % C276 N/A C276 Fluke 700P psi/1 69 M Pa/ % C276 N/A C276 readings update twice per second, and may be displayed in up to 11 different units. Modules are interchangeable across your calibrators. Each module includes instruction sheet, metric adapter (except P29, P30, and P31), a NIST traceable certificate of calibration, and a one year warranty. Modules can be locally calibrated using the Fluke 700PCK Pressure Calibration Kit, a PC, and a precision pressure source. 13

14 Pressure Calibrators Fluke 718 Pressure Calibrator. Pump up the pressure. The Fluke 718 Pressure Calibrator offers a new approach to pressure calibration. A complete, self-contained calibration solution, the 718 offers: Built-in pressure / vacuum hand pump, with vernier and bleed valve. Pressure measurement to 0.05 % of full span, using an internal pressure sensor. Pressure measurement to 10,000 psi / 700 bar using any of the Fluke 700Pxx Pressure Modules. Wide range of selectable measurement units for pressure. Current measurement with % accuracy and ma resolution. 24 volt loop power supply. 1 /8 inch NPT female pressure fitting. Min-Max Hold functions. Compact size and weight. Simple, push-button user interface. Rugged and reliable, ideal for field use G and 100G Pressure Calibrators Measure pressure and vacuum to 0.05 % of full scale with internal 30 psig sensor (717 30G) or internal 100 psig sensor ( G) - 1/8 NPT pressure fitting - Compatible with noncorrosive gases and liquids Measure Pressure to 10,000 psi/700 bar using one of the Fluke 700Pxx Pressure Modules Measure ma with % accuracy and ma resolution, while sourcing 24 V loop power Ordering information Fluke US Pressure Calibrator Fluke US Pressure Calibrator Fluke G Pressure Calibrator Fluke G Pressure Calibrator 14

15 Specifications (18 C to 28 C, one year) Pressure G G G G Function Range Resolution Accuracy Notes Measure Pressure 1-12 to 30 psi psi 0.05 % full Gases/liquids 717 only (internal sensor) (-83 to 207 kpa) scale (0.01 kpa) (non-corrosive) Use the 718 Over pressure 3xFS with non-corrosive gases only Zero, Min, Max, Hold, Damp Measure Pressure 1-12 to 100 psi 0.01 psi 0.05 % full scale Gases/liquids 717 only (internal sensor) (-83 to 690 kpa) (0.1kPa) (non-corrosive) Use the 718 Over pressure 2xFS with non-corrosive gases only Zero, Min, Max, Hold, Damp Measure Pressure 1 28 Pressure To psi, To 0.05 % of full Media compatibility (with Pressure 1.0 in. H 2 0/ per Pressure span, per per Pressure Module Modules, Modules) 0.25 kpa to Module specs 2 pressure Specs 2 Over pressure per 10,000 psi/ Module Specs 2 Zero, Min, Max, pressure 69 MPa Hold, Damp module specs 2 Source Pressure, -11 psig to N/A N/A Use the 718 with nonbuilt-in pump full scale corrosive gases only Measure ma 0 to 24 ma ma % + 1 count Loop supply 24 V dc N/A ±10 % Drive; 20 ma into 1000 Ω for battery >6.8 V; 700 Ω for battery 5.8 to 6.8 V 1 Supported Pressure Units; psi, in. H 2 0 (4 C), in. H 2 0 (20 C), cm H 2 0 (4 C), cm H 2 0 (20 C), bar, mbar, kpa, inhg, mmhg, kg/cm 2 2 Pressure Module Specifications, see page 13 General specifications for all Fluke 717, 718 calibrators Maximum voltage: 30 V Non-operating temperature: -40 C to 60 C Operating temperature: -10 C to 55 C Relative humidity: 95 % (10 C to 30 C); 75 % (30 C to 40 C); 45 % (40 C to 50 C); 35 % (50 C to 55 C) Operating altitude: 3,000 m max Shock: 1 m drop test Vibration: Random, 2 g, Hz Safety: CSA C22.2 No :1992 EMC: EN :1992 and EN55022:1994 Class B Size/weight (717): 187 mm L x 87 mm W x 32 mm D (7.35 in L x 3.41 in W x 1.25 in D) 330 g (12 oz) Size/weight, (717 with holster and FlexStand ): 201mm L x 98 mm W x 52 mm D (7.93 in L x 3.86 in W x 2.06 in D) 600 g (21 oz) Size/weight (718): 210 mm L x 83 mm W x 62 mm D (8.25 in L x 3.27 in W x 2.44 in D) 737 g (26 oz) Size/weight, (718 with holster): 216 mm L x 94 mm W x 66 mm D (8.50 in L x 3.72 in W x 2.60 in D) 992 g (35 oz) Power: 9 V battery ANSI/NEDA 1604 A or IEC 6LR619V alkaline; two batteries in 718 Battery Life: 4 to 20 hours, typical, depending on functions used Warranty: Three years (one year on pressure pump in Fluke 718) 15

16 Temperature Calibrators Feel the Heat! The Fluke 724 Temperature Calibrator is a powerful yet easy-to-use calibrator. Use the measure and source functions to test and calibrate almost any temperature instrument. Easy to read dual display lets you view input and output simultaneously Measure RTDs, thermocouples, ohms, and volts to test sensors and transmitters Source/simulate thermocouples, RTDs, volts, and ohms to calibrate transmitters Perform fast linearity tests with 25 % and 100 % steps Execute remote tests with auto step and auto ramp Power transmitters during test using loop power supply with simultaneous ma measurement Store frequently-used test setups for later use Compact, streamlined shape makes it easy to carry Rugged, reliable design stands up to field use Backlight lets you work in poor light Large battery capacity of four AA cells Battery door for easy changes 16 Simultaneous Function Capability Channel A Channel B ma DC M ma DC with 24 V loop supply M mv DC M or S V DC Measure M V DC Measure V DC Source M or S 0 to 3200 Ohms M or S Thermocouple J, K, T, E, R, S, B, L, U, N M or S RTD Ni120; Pt100 (3926); Pt100 (JIS); Pt100, 200, 500, 1000 (385) M or S M = Measure S = Source/Simulate For 724 Performance and General Specifications, refer to the 24 V loop, ma measure, thermocouple, RTD, voltage dc and General Specifications on page 7. Ordering information Fluke 724 Temperature Calibrator Each calibrator includes: TL75 Test Leads, AC70A Test Clips, one pair of stackable test leads, Product Overview Manuals in English, French, German, Spanish, Italian, Dutch, Norwegian, Danish, Swedish, Finnish, Portuguese, Korean, Chinese, and Japanese, Users Manuals on CD-ROM; NIST-traceable certificate of calibration; CE and CSA markings. Fluke-712 RTD Calibrator Fluke-714 Thermocouple Calibrator Each calibrator includes: C81Y protective yellow holster with FlexStand, Test Leads and Alligator Clips (712 only), single 9 V alkaline battery, Instruction Sheet (14 languages), NIST-traceable certificate of calibration; CE and CSA markings.

17 712 RTD Calibrator Measure temperature from RTD output Simulate RTD output Rosemount pulsed RTD transmitter compatible Operates with seven types of RTDs Measure additional RTDs using Ohms measurement function Simulate additional RTDs using Ohms source function F or C selectable Four shrouded banana jacks 714 Thermocouple Calibrator Measure temperature from TC output Simulate TC output Operable with nine types of thermocouples Calibrate linear TC transmitter with mv source function Selectable F or C Thermocouple mini-jack termination Available as accessories; Fluke 700 TC1 and TC2 Thermocouple Mini-plug Kits Summary specifications (18 C to 28 C, one year) RTD (714) TC (714) Function Range Resolution Accuracy Notes Measure/simulate -200 to 800 C 0.1 C, 0.1 F 0.33 C, 0.6 F Pt; (385); RTD (Pt 100) (Pt 100) Pt 100 (3926); Pt 100 (3916) JIS; Ni 120 (672) Measure/simulate 15 Ω to 3200 Ω 0.1 Ω 0.1 Ω to 1 Ω Resistance Measure/simulate -200 to 1800 C, 0.1 C or F 0.3 C + 10 µv 9 TC types; Thermocouple depending on type (1 C or F; BRS) (K,-200 to 1370 C) J K T E R S B per NIST (K,-200 to 1370 C) 175 and ITS-90 L U per DIN and IPTS-68 Measure/simulate mv -10 to 75 mv 0.01 mv % + 1 count General specifications for Fluke 712 and 714 calibrators Maximum voltage: 30 V Non-operating temperature: -40 C to 60 C Operating temperature: -10 C to 55 C Relative humidity: 95 % (10 C to 30 C); 75 % (30 C to 40 C); 45 % (40 C to 50 C); 35 % (50 C to 55 C) Operating altitude: 3,000 m max Shock: 1 m drop test Vibration: Random, 2 g, Hz Safety: CSA C22.2 No :1992 EMC: EN :1992 and EN55022:1994 Class B Size/weight: 187 mm L x 87 mm W x 32 mm D (7.35 in L x 3.41 in W x 1.25 in D) 330 g (12 oz) Size/weight, (with holster and FlexStand ): 201mm L x 98 mm W x 52 mm D (7.93 in L x 3.86 in W x 2.06 in D) 600 g (21 oz) Power: 9 V battery ANSI/NEDA 1604A or IEC 6LR619V alkaline Battery Life: 4 to 20 hours, typical, depending on functions used Warranty: Three years 17

18 R Loop Calibrators Fluke 787 ProcessMeter. Double your power. A maintenance and calibration tool that will be at home in every instrumentation technician s tool box, the Fluke 787 ProcessMeter combines a DMM and a Loop Calibrator in one rugged, handheld tool, for about what you would expect to pay for a loop calibrator alone. Based on the trusted Fluke 87 DMM, the 787 adds the ability to measure, source, and simulate dc loop current with 0.05% accuracy and 1 microamp resolution. In addition to the capabilities listed in the spec. table, the 787 offers: Simultaneous ma and % of scale readout on ma output. 25 % Manual Step plus Auto Step and Auto Ramp on ma output. Clear LCD with backlight; 4,000 counts (30,000 counts for dc current). Min/Max/Average/Hold/ Relative modes. Externally accessible battery for easy battery changes V overload protection on V, ohms, frequency. 150 V overload protection on ma, backed-up by 440 ma 1000 V fuse. Ordering information Fluke 787 ProcessMeter Includes: C81Y Protective Yellow Holster with Flex-Stand, TL75 Safety-Designed Test Lead Set plus AC70A Alligator Clips, one 9V alkaline battery (installed), Users Manual and Quick Reference Guide. 18

19 Specifications (18 C to 28 C, one year) Measurement Best Accuracy Function Range and Resolution (% of reading + LSD) VDC mv, V, V, 0.1 % V, 1000 V VAC (true-rms) to 500Hz mv, V, V, 0.7 % V, 1000 V madc ma.05 % + 2 A DC A (0.440 A continuous) 0.2 % + 2 A AC A (0.440 A continuous) 1 % + 2 Resistance Ω, kω, kω, 0.2 % kω, 4.0 MΩ, 40 MΩ Frequency (0.5 Hz to 20 khz) Hz, Hz,.005 % khz Diode Test V (shows diode 2 % + 1 voltage drop) Continuity Beeps for resistance < approx 100 ohms Drive Accuracy Output Function Range and Resolution Capability (% of span) DC Current Output to ma or 12 V.05 % (internal battery operation) to ma compliance, (selectable at power-up) or, 500 Ohms, Over-range to ma DC Current Simulate to ma or 1000 Ohms,.05 % (ext. 24 Volt loop supply) to ma (selectable at power-up) Over-range to ma Current adjustment modes Manual: Coarse, Fine, 25 % step Automatic: Slow Ramp, Fast Ramp, 25 % step General specifications for the Fluke 787 ProcessMeter Maximum voltage applied between any jack and earth ground: 1000 V rms Storage temperature: -40 C to 60 C Operating temperature: -20 C to 55 C Temperature coefficient: 0.05 x (specified accuracy) per C (for temperatures < 18 C or > 28 C) Relative humidity: 95 % up to 30 C; 75 % up to 40 C; 45 % up to 50 C; 35 % up to 55 C Vibration: Random, 2 g, Hz Shock: One meter drop test Safety: Conforms to IEC , ANSI/ISA S and CAN/CSA C22.2 No Over-voltage Category III Size: 32 mm H x 87 mm W x 187 mm L (1.25 in H x 3.41 in W x 7.35 in L) Size, with holster and FlexStand : 52 mm H x 98 mm W x 201 mm L (2.06 in H x 3.86 in W x 7.93 in L) Weight: 369 g (13 oz); with holster and Flex-Stand 638 g (22.5 oz) Battery: Single 9 V Alkaline battery (ANSI/NEDA 1604A or IEC 6LR61) Battery life: 50 hours typical (measurement), 12 hours typical (sourcing 12 ma) Warranty: Three years 19

20 Loop Calibrators New Product Fluke 707 Loop Calibrator One click and you ll be hooked the fast, one-handed tool for loop checks. This feature-rich solution combines the best features of a push-button and knob-base loop calibrator and offers: Large display and simple, push-button interface for ease of use. Simultaneous ma and % readout for quick, easy, interpretation of readings. ma accuracy of %. Push button 25 % steps for fast, easy linearity checks % span check for fast confirmation of zero and span. Summary specifications (18 C to 28 C, one year) Selectable slow ramp, fast ramp, and step to provide smooth outputs for valve slewing and loop functional tests. 24 volt internal loop supply, so you can power and read a transmitter at the same time without carrying a DMM. Single 9 V battery that is easily changed ma or 4-20 ma default start up modes. Innovative output adjustment dial with 1 ma and 100 ma resolution. HART mode connects 250 Ω resistor in series with 24 V loop for compatibility with HART communicators. Function Range Resolution Accuracy Voltage measure 0 to 28 V.001 V ± (.015 % Rdg + 2 counts) ma measure 0 to 24 ma.001 ma.015 % Rdg + 2 LSD ma source 1 0 to 24 ma.001 ma.015 % Rdg + 2 LSD ma simulate 2 0 to 24 ma.001 ma.015 % Rdg + 2 LSD Loop supply 24 V dc n/a 24 V Temperature coefficient, - 10 to 18 ºC, 28 to 55 ºC, ±.005% of range per ºC 1 Max load, 1200 Ohms; 950 Ohms at 20 ma in HART mode 2 Max applied voltage for simulation, 30 V 20 General Specifications for the Fluke 707 calibrator Maximum voltage: 30 V Non-operating temperature: -40 to 60 ºC Operating temperature: -10 to 55 ºC Relative humidity: 0 to 90 % (0 to 35 ºC); 0 to 70 % (35 to 55 ºC) Operating altitude: 3,000 meters max. Shock and vibration: Per MIL-T for a Class 2 Instrument Safety: CSA C22.2 No : 1992 EMC: EN :1992 and EN55022:1994 Class B Size/weight: 6.0 in L x 2.8 in W x 1.6 in D (152 mm L X 70 mm W x 41 mm D) 8 oz (224 g) Size/weight with C10 Holster: 6.4 in L x 2.9 in W x 1.9 in D (164 mm L x 75 mm W x 47 mm D) 12.3 oz. (350 g) Battery: One 9 V alkaline Battery life: 18 hours typical, at 12 ma Warranty: Three years Ordering information Fluke 707 Loop Calibrator Fluke 705 Loop Calibrator Fluke 715 Volt/mA Calibrator Each calibrator includes: TL75 test leads, AC70 Test Clips, C-10 Holster, Instruction sheets (English, French, German, Spanish, Italian, Dutch, Norwegian, Danish, Swedish, Finnish, Portuguese, Korean, Chinese, Japanese), NIST-traceable certificate of calibration; CE and CSA markings.

21 Fluke 705 Loop Calibrator. A large display and simple, push button interface for ease of use Simultaneous ma and % readout for quick, easy, interpretation of readings ma accuracy of 0.02 % Push button 25 % steps for fast, easy linearity checks Span Check for fast confirmation of zero and span General specifications for the Fluke 705 calibrator Maximum voltage: 30 V Non-operating temperature: -40 C to 60 C Operating temperature: -10 C to 55 C Relative humidity: 0 to 90 % (0 to 35 C); 0 to 70 % (35 to 55 C) Operating altitude: 3,000 m max Shock and vibration: Per MIL-T for a Class 2 Instrument Safety: CSA C22.2 No :1992 EMC: EN :1992 and EN55022:1994 Class B Size/weight: 152 mm L x 70 mm W x 41 mm D (6.0 in L x 2.8 in W x 1.6 in D) 340 g (12 oz) Size/weight, with C10 holster: 164 mm L x 75 mm W x 47 mm D (6.4 in L x 2.9 in W x 1.9 in D) 500 g (18 oz) Battery: One 9 V alkaline; Battery Life: 18 hours typical, at 12 ma Warranty: Three years Summary specifications (18 C to 28 C, one year) Function Range Resolution Accuracy Voltage measure 0 to 28 V V.025 % Rdg + 1 LSD ma measure 0 to 24 ma ma.02 % Rdg + 2 LSD ma source* 0 to 24 ma ma.02 % Rdg + 2 LSD Loop supply 24 V dc n/a 10 % Temperature Coefficient, -10 to 18 C, 28 to 55 C, ±.005 % of range per C; * Max load, 1000 Ohms; Max applied voltage for simulation, 30 V 715 Volt/mA Calibrator Measure loop current (0-20 ma, 4-20 ma) signals with % accuracy and ma resolution Measure voltage output process signals from PLCs, transmitters Source or simulate 24 ma loop current Source voltage to 100 mv or 10 V 24 V loop supply with simultaneous current measurement General specifications for Fluke 715 calibrator Maximum voltage: 30 V Non-operating temperature: -40 C to 60 C Operating temperature: -10 C to 55 C Relative humidity: 95 % (10 C to 30 C); 75 % (30 C to 40 C); 45 % (40 C to 50 C); 35 % (50 C to 55 C) Operating altitude: 3,000 m max Shock: 1 m drop test Vibration: Random, 2 g, Hz Safety: CSA C22.2 No :1992 EMC: EN :1992 and EN55022:1994 Class B Size/weight: 187 mm L x 87 mm W x 32 mm D (7.35 in L x 3.41 in W x 1.25 in D) 330 g (12 oz) Size/weight, (with holster and FlexStand ): 201 mm L x 98 mm W x 52 mm D (7.93 in L x 3.86 in W x 2.06 in D) 600 g (21 oz) Power: 9 V battery ANSI/NEDA 1604A or IEC 6LR619 V alkaline Battery Life: 4 to 20 hours, typical, depending on functions used Warranty: Three years Summary specifications (18 C to 28 C, one year) Function Range Resolution Accuracy Notes Measure/simulate 0 to 24 ma ma % + 2 counts Sink (simulate transmitter) ma/% of span (-25 % to 125 %) Display ma or % of span Measure/simulate mv 0 to 100 mv 0.01 mv 0.02 % + 2 counts Measure/simulate V 0 to 10 V V 0.02 % + 2 counts Volt/mA 21

22 Meters Fluke 51 Single Input Digital Thermometer Fluke 52 Dual Input Digital Thermometer Fluke 51 Series II and 52 Series II product features: Large backlit dual display shows any combination of T1, T2 (52 only), T1-T2 (52 only), plus MIN, MAX, or AVG Relative time clock on MIN, MAX, and AVG provides a time reference for major events. Electronic Offset function allows compensation of thermocouple errors to maximize overall accuracy Measures J, K, T, and E-types of thermocouples Readout in C, F, or Kelvin (K). Splash and dust resistant case protected by impact absorbing holster User-friendly front panel is easy to set up and operate Sleep mode increases battery life; typical 1000-hour battery life Battery door allows easy battery replacement without breaking the calibration seal Optional ToolPak accessory allows the thermometer to hang from any metal object (with the rare earth magnet) or secure around a pipe (with hook-and-loop straps) for hands-free operation Three-year warranty 22 Fluke 53 Single Input Digital Thermometer with data logging Fluke 54 Dual Input Digital Thermometer with data logging The Fluke 53 Series II and 54 Series II include all the features listed above plus: Data Logging up to 500 points of data with user adjustable recording interval Additional thermocouple types R, S, and N (for a total of 7 different types) Real time clock captures the exact time of day when events occur Recall function allows logged data to be easily reviewed on the meter display IR communication port allows data to be exported to optional FlukeView Temperature PC software for further analysis and graphing

23 189 Digital Multimeter % basic dc accuracy Basic DC accuracy of % 50,000-count primary display for high resolution measurement readings MIN/MAX/AVG time-stamped with a real-time clock for enhanced troubleshooting Temperature measurements in ºC and ºF using optional K-type thermocouple Stand-alone logging to internal memory of up to 3 days of measurement changes Use optional FlukeView Forms software for further data analysis, custom documentation and PC logging 65 Infrared Thermometer Range -40 to 500 C (-40 to 932 F) 0.1 C resolution up to 200 C Measurements in less than 1 second Bright laser beam for easy targeting 8:1 Optical Resolution MIN/MAX reading capture Large backlit dual display 43B Power Quality Analyzer Combines the most useful capabilities of a power quality analyzer, multimeter and scope Measure power, harmonics, and catch intermittents Track intermittent problems and power system performance 16 Multimeter 4000-count digital display Rotary dial 0.9 % basic dc accuracy All standard DMM functions Sleep mode VChek Capacitance MIN/MAX record w/time stamp Continuity capture Three-year warranty Holster w/flex-stand Thermocouple included Temperature range from -40 C to 400 C (-40 F to 750 F) Microamps 23

24 Accessories C700 Hard Carrying Case (700 Series) Hard carrying case with custom-cut foam liner C781 Soft Carrying Case Rugged, close-fitting fabric carrying case for documenting process calibrator. A separate, detachable pouch holds test leads and accessories. C789 Soft Carrying Case Rugged, three-compartment fabric carrying case for documenting process calibrator and accessories BP7235 NiMH Battery Pack 7.2 V 3500 ma-hour rechargeable NiMH battery pack BP7217 NiCd Battery Pack 7.2 V 1700 ma-hour rechargeable NiCd battery pack Fluke 700BCW Bar Code Wand This HBSW-8200 Bar Code Wand reads eight common bar code symbologies. Fluke 700-IV Current Shunt Conversion factor: 10 mv = 1 ma Accuracy (% of input, 1 year): % Input current: 0 to 55 ma Input resistance: 250 Ω nominal Output resistance: 10 Ω nominal Accuracy specification applies from +18 C and C Maximum input voltage: 30 V dc Fluke ToolPak Kit includes: universal hanger clips (2), hook & loop straps (2 lengths) and strong magnet. Combine components to meet most hanging needs. Attaches to the back of an 80 Series IV meter, a Fluke 724 or 725 Process Calibrator or the 51, 52, 53 and 54 Series II Digital Thermometers. Fluke LockPak Kit includes a locking accessory. Attaches to the back of an 80 Series IV meter or a Fluke 724 or 725 Process Calibrator to help deter theft. Accepts most common locks (not included). 24

25 Pressure Accessories Fluke 700PTP Pneumatic Test Pump The Fluke 700PTP is a handheld pressure pump designed to generate either vacuum to psi/-0.8 bar or pressure to 360 psi/25 bar. Fluke 700HTP Hydraulic Test Pump The Fluke 700HTP is designed to generate pressures up to 10,000 psi/700 bar. Fluke 700PRV Pressure Relief Valve Kit The Fluke 700PRV consists of two relief valves (1360 and 5450 psi) to be used with the 700HTP Hydraulic Test Pump. These relief valves will protect the most commonly used Fluke pressure modules from damage due to accidental over-pressurization. 1 /4 BSP male parallel thread to fit Fluke 700HTP. Fluke 700PMP Pressure Pump The Fluke 700PMP is a hand-operated pressure pump to provide pressures up to 150 psi/1000 kpa. Output fitting is 1 /8 FNPT. Fluke 700HTH Hydraulic Test Hose The Fluke 700HTH is a 10,000 psi, 700 bar test hose that connects to a calibration unit under test from a Fluke 700HTP hydraulic test pump. Fluke 700ILF In-line Filter The Fluke 700ILF can be used to isolate the calibrator from incidental contact with fluids present in the gas medium being measured. Particularly useful with the 718 calibrator to help keep moisture or oils from contaminating the on-board pump. Fluke 700LTP Low Pressure Test Pump The Fluke 700LTP is designed to generate either vacuum to 12 psi/-.85 bar or pressures to 30 psi / 2000 mbar. The Fluke 700 LTP is primarily intended for low pressure applications and features a find adjust vernier and an adjustable slow-bleed relief valve. 25

26 Accessories 80PK-1 & 80PJ-1 Bead Probes This basic, inexpensive thermocouple offers good accuracy and fast response. (Not suitable for liquid immersion.) 80PK-1 is compatible with K-type thermometers; 80PJ-1 works with J-Type thermometers Measurement range: -40 C to 260 C (-40 F to 500 F) 80PK-8 Pipe Clamp Temperature Probe Type-K thermocouple for fast temperature and super heat measurements of pipe surfaces. Measurement range: -29 to 149 C (-20 to 300 F) for pipe surfaces from 6.4 mm to 34.9 mm 80T-150U Universal Temperature Probe For highly accurate measurement of air, surface, and non-corrosive materials. Measurement range: -50 C to 150 C (-58 F to 302 F) Output: 1mV/ C or 1mV/ F (switch selectable) 80T-IR Infrared Surface Temperature Probe For quick, non-contact temperature measurement in less than one second Instantly measures temperatures from -18 C to 260 C (0 to 500 F) Highly repeatable readings displayed in C or F Optical resolution 4:1 Output 1mV/ C or 1mV/ F (switch selectable) 80TK Thermocouple Module Converts digital multi-meters to a thermometer, via standard banana plugs. Uses K type thermocouples, listed below 70TC1 and TC2 Thermocouple Plug Kits Miniconnector plug kits to terminate thermocouple wire for connection to a process calibrator. Connections have a thermoplastic body. Connections and contacts are of appropriate thermocouple metalurgy. TC1: 11 types including one each J, K, T, E, R/S, B(cu), L, U, C, N. TC2: 5 types including 2 each J, K and one each T, E, R/S. 26

27 Accessories Compatibility Chart 743B 741B / /54 700Pxx Pressure Modules BP7217 NiCd Battery Pack BP7235 NiMH Battery Pack BE9005 Battery Eliminator BC7217 Battery Charger 700BCW Bar Code Wand 700BCA Bar Code Adapter TPAK 80-4 ToolPak LPAK 80-4 LockPak 700TC1 and TC2 Thermocouple Plug Kits 80CJ-M or 80CK-M Mini-connectors 80PK Thermocouple Probes (all) 4 700RTD SPRT Probe 700-IV Current Shunt 700ILF In-line Filter 700LTP Low-pressure Test Pump 700PMP Pressure Pump 3 700PTP Pnuematic Test Pump 3 700HTH Hydraulic Test Hose 3 700HTP Hydraulic Test Pump 3 787CAL Calibration Kit 80T-IR Infrared Probe 80PK-IR Infrared Probe 80TK Thermocouple Module 80T-150U Temperature Probe 80i-400 AC Current Clamp i410 AC/DC Current Clamp i1010 AC/DC Current Clamp C10 Holster, C12A Case C25/C100 Cases C781 Soft Carrying Case C789 Soft Carrying Case C700 Hard Carrying Case C120/C125 Cases C510 Leather Case C530 Leather Accessory Case C550 Tool Bag PV350 Pressure Vacuum Module Fiber Optic Meter FOM 1 20 amps AC minimum 2 DC current only 3 External pump required only when using high pressure modules 4 Use with 80TK 27

28 Why Choose Fluke Process Tools? Products Fluke has a complete line of Process Tools to amplify your skills and extend your power. They: Are rugged, reliable products you can count on. Offer world class accuracy and resolution. Have superior user interface. Test drive a Fluke Virtual Calibrator or Meter online. Fluke 707 at Fluke 725 at Fluke 189 at Fluke 43B at Named first in Field Calibrators by Readers of Control Magazine 1998, 1999, 2000, 2001, Low Cost of Ownership Strong warranty backed by the Fluke name Conservative specs you can rely on Long calibration intervals reduce calibration costs Low maintenance and repair costs Service and Repair Locations Worldwide To contact Fluke or to locate an authorized service center, call one of the following telephone numbers: USA: FLUKE ( ) Canada: FLUKE ( ) Europe: Japan: Singapore: Other countries: Or visit Fluke s Web site at Visit us at Fluke. Keeping your world up and running. Fluke Corporation PO Box 9090, Everett, WA USA Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands For more information call: U.S.A. (800) or Fax (425) Europe/M-East/Africa (31 40) or Fax (31 40) Canada (800) 36-FLUKE or Fax (905) Other countries +1 (425) or Fax +1 (425) Web access: Fluke Corporation. All rights reserved. Printed in U.S.A. 1/ B-ENG-N Rev G