AN320 Application note Operation of a Trisil crowbar type protection diode Introduction

Transcription

1 Application note Operation of a Trisil crowbar type protection diode ntroduction n the field of parallel protection, the devices used have two main functions in transient operation. Limit the voltage. Divert the surge current. f the first function is carried out perfectly by an avalanche junction, confirmed by the success of the Transil series, the second is limited by voltage permanently present across the diode terminals. Use of increasingly sophisticated but fragile electronic components and publication of new standards do not allow the use of Transil diodes in certain applications. This problem is solved by the use of a semiconductor device with two conducting states such as the thyristor (or Triac in the bidirectional version). STMicroelectronics has developed this type of component under the trade name of Trisil. This Application note describes the operation of the Trisil. Figure 1. / characteristic of a Trisil PP H BO Transient operation Standby operation A B RM C RM BR BO D TM: Trisil is a trademark of STMicroelectronics TM: Transil is a trademark of STMicroelectronics July 21 Doc D 5649 Rev 3 1/13

2 Trisil characteristics AN32 1 Trisil characteristics 1.1 Electrical characteristic The electrical characteristic of the Trisil is similar to that of a Triac (see Figure 1) except that the component has only two terminals. Triggering in this case is not done via a gate but by an internal mechanism dependent on the current flowing through it. 1.2 Operation seen from the outside n normal operation, the Trisil is biased at a voltage lower than or equal to the standby voltage ( RM ). At that point of the characteristic, the leakage current is about 1 na and the presence of the Trisil connected across the equipment to be protected does not disturb its operation (see Figure 2). The characteristic data at this point includes: Leakage current Electrical capacity Reliability of the component in blocking mode Figure 2. Stand by characteristics RM RM As the voltage increases beyond BR, the Trisil impedance drops from practically infinite to a few ohms. The Trisil remains biased at its avalanche voltage and its operation is then identical to that of a Transil diode (see Figure 3). The characteristic parameters at this level are the limiting voltage (breakover voltage of the component, BO ) and the time for switching between the blocked and conducting states. 2/13 Doc D 5649 Rev 3

3 Trisil characteristics Figure 3. Avalanche characteristic of the Trisil BO BR BO For current values higher than BO, the voltage across the Trisil drops to a few volts and the high currents permitted without damage are possible due to the low value of this voltage, since the physical limit is dependent on the dissipated power (see Figure 4). Figure 4. Triggering, and on-state characteristics PP BO The characteristic parameter is then the possibility of withstanding surge currents (peakpoint current, PP ). Return to standby operation by turning off the Trisil takes place when the current flowing through it drops below H. This is the characteristic parameter for switching from the conducting to the blocked state (see Figure 5). Doc D 5649 Rev 3 3/13

4 Trisil characteristics AN32 Figure 5. Return to standby operation H RM RM The surge current associated with the disturbance is diverted through the Trisil as soon as it begins to operate in the avalanche mode (see Figure 3) and the voltage limitation results from the electrical characteristic at this point. The behavior of the Trisil is here identical to that of the Transil. The difference depends on the level of the breakover current, BO, where the triggering of the thyristor structures take place. This phenomenon results in absolute limitation independently of the current level, and a capacity to divert currents much higher than those possible for an avalanche diode (Transil). Furthermore, this limitation is independent of the avalanche voltage of the device. 4/13 Doc D 5649 Rev 3

5 Trisil characteristics 1.3 Limiting property Because of its operating mode, the Trisil results in absolute voltage limitation, independently of the surge current level, Figure 6 and of the slope of the applied voltage ramp (see Figure 7). Figure 6. Correlation between the voltage and the surge current A - Transil B - Trisil PP PP CL BO Figure 7. Correlation between the limiting voltage and the surge voltage ramp BO oltage across the Trisil d/dt n particular, if the surge current is higher than the guaranteed value in the catalogue, without however exceeding the physical limits of the component, the voltage across a Transil could reach the critical value destroying the equipment to be protected. For a Trisil, this risk is excluded. Finally, for a surge current much higher than the guaranteed value, destruction of the Trisil always results in a short-circuit thus providing absolute protection for the equipment located downstream. Doc D 5649 Rev 3 5/13

6 Trisil characteristics AN Behavior in case of current surges The ability of semiconductor components to withstand high currents in transient operation is limited for pulses longer than 1 ns by a second breakdown due to heat. This phenomenon, although not destructive, is considered as the normal utilization limit in so far as the behavior of the component depends on the external circuit. The temperature rise within the semiconductor is thus the parameter which defines the behavior of the component and its capacity to withstand current surges. t is given by Equation 1: Equation 1: T j = T A + Z TH ON x RS With T j : instant temperature at the junction level T A : ambient temperature Z TH : transient thermal impedance (as a function of the duration of the pulse) ON : voltage across the terminals of the component in the conducting state RS : transient current flowing through the component This equation clearly shows the advantage of the Trisil. A decrease in the voltage across its terminals enables it to conduct a much higher current than the avalanche diode for the same junction temperature. Since the voltage to be taken into consideration for the calculation is that in the conducting state, the permitted current levels in transient operation are independent of the avalanche voltage and the guaranteed values are identical for all the types of a given series (see Figure 8). Figure 8. Comparison of the limited transient currents for a Transil and a Trisil in the similar cases (SMB). PP(A) Trisil 8/2µs 12 1 Trisil 8 1/1µs 6 Transil 8/2µs 4 Transil 2 1/1µs BR() The maximum junction temperature taken into account in transient operation is not that given in the catalogues (junction temperature in operation or in storage) but corresponds, with a certain safety margin, to the second breakdown due to thermal causes, i.e. about 35-4 C. This high current capacity can be applied in AC operation at the 5 Hz industrial frequency (see Figure 9), which is particularly interesting in telephony where equipment should be protected against overvoltages resulting from accidental coupling of the telephone line with 6/13 Doc D 5649 Rev 3

7 Trisil characteristics the power distribution network. This type of protection is required by certain standards used in telecommunications. Figure 9. Long duration overload test (A) 1 F = 5 Hz 1 pair of pulses t(s) 1.5 Response time The response time of the component is the time it requires to limit the voltage. From this point of view the Trisil has exactly the same behavior as a Transil. The time is that required to switch from the standby operating point to the avalanche voltage. This is almost instantaneous. This time should not be confused with that required to pass from the breakover point ( BO ) to the conducting characteristic. This time is longer but does not influence the limiting capability of the device. 1.6 Operation within the avalanche area This section concerns the segment BR - BO (see Figure 3) of the Trisil characteristic between the blocked state and the conducting state at low ON. This portion of the characteristic is identical to that of an avalanche diode. Thus within this area, DC, AC or pulse-type operations are permitted. The currents are limited depending on the possibilities of junction-ambient air heat dissipation. The maximum current is defined by the following: Equation 2: T j = T A + R TH BO MAX T jmax = 15 C The condition when the Trisil is not triggered is defined as follows: Equation 3: MAX < BO The main differences from Equation 1 are: Maximum junction temperature which is now that given by the catalogue, i.e. 15 C oltage which is that of the avalanche mechanism Continuous thermal resistance replacing the transient thermal impedance n AC operation, although Equation 2 still holds good, the voltage-current diagram as a function of time shown in Figure 1 is clearer. Doc D 5649 Rev 3 7/13

8 Trisil characteristics AN32 The value of the breakover current ( BO ) plays an important part in the capacity of the device in avalanche operation. f this value is high (see Figure 11A), the current in the component must be limited by a suitable series resistor. For lower values, avalanche operation takes place without destruction whatever the external circuit. Figure 1. AC operation in the avalanche mode R S S T T Circuit to be protected T BO BR S t T BO t BO Figure 11. Conditions for non destructive operation in the avalanche mode A - Case in which the current should be limited by the external circuit R S > limit R S B - Correct operation whatever the external circuit Destruction by thermal effect P = Constant Destruction by thermal effect P = Constant S / R Limit R S BO R S BO S 8/13 Doc D 5649 Rev 3

9 Physical operation 2 Physical operation A Trisil consists of two thyristors connected back to back. t will suffice to explain the operation of one thyristor. The other operates in the same way if the voltage across the component is reversed. Figure 12. Operation in the blocked mode () N N+ 1 + N+ 1 + P 1 + J 1 J 2 N Leakage current N2 P 2 + J 3 C B A Doc D 5649 Rev 3 9/13

10 Physical operation AN32 Figure 13. Operation in the avalanche mode () N N+ 1 + N+ 1 + P 1 + J 1 J 2 Avalanche current N P 2 + J 3 C B A Application of a negative voltage on cathode N++ results in forward biasing of junctions J 1 and J 3 and reverse biasing of J 2. The current observed is thus the leakage current of junction J 2. When the voltage exceeds a certain value, junction J 2, which is reverse biased, begins to operate in the avalanche mode. The structure up to this current level operates like a diode (junction J 2 ). The side current biases the P 1 layer next to the N 1 part of the emitter. The highly doped N 1 layer has the same potential. The P 1 area at the surface is forced to the same potential as the N 1 region by metallization. 1/13 Doc D 5649 Rev 3

11 Physical operation Figure 14. Thyristor effect of the Trisil ( ) N N 1 ++ N P 1 + J 1 J 2 N 2 N P 2 + J 3 C B A As the avalanche current increases, this difference of potential can reach the threshold of.6, a value which is sufficient to create injection of electrons from the cathode towards the P 1 area and thus trigger thyristor N 1 P 1 N 2 P 2. The electrons thus injected into P 1 in fact will reach J 2 by diffusion, and cross it under the effect of the electrical field operating in the space charge of the reverse biased J 2 junction. n N 2, the electrons help to reduce the potential of this area compared with P 2 and as a result inject holes from P 2 towards N 2. These holes travel in the reverse direction because of their polarity. When they arrive at P 2 they help to increase the potential of P 1 with respect to N 1, this time resulting in the injection of electrons from N 1 to P 1. The procedure is cumulative. The excess electrons in N 2 and the holes in P 1 will compensate the fixed charges of the space charge and will thus suppress it. Junction J 2 will act as a forward biased junction and the voltage across the component will drop. Doc D 5649 Rev 3 11/13

12 Revision history AN32 3 Revision history Table 1. Document revision history Date Revision Changes February First issue. 1-May-24 2 Stylesheet update. No content change. 5-Jul-21 3 Updated trademark statements. 12/13 Doc D 5649 Rev 3

13 Please Read Carefully: nformation in this document is provided solely in connection with ST products. STMicroelectronics N and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. f any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWSE SET FORTH N ST S TERMS AND CONDTONS OF SALE ST DSCLAMS ANY EXPRESS OR MPLED WARRANTY WTH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS NCLUDNG WTHOUT LMTATON MPLED WARRANTES OF MERCHANTABLTY, FTNESS FOR A PARTCULAR PURPOSE (AND THER EQUALENTS UNDER THE LAWS OF ANY JURSDCTON), OR NFRNGEMENT OF ANY PATENT, COPYRGHT OR OTHER NTELLECTUAL PROPERTY RGHT. UNLESS EXPRESSLY APPROED N WRTNG BY AN AUTHORZED ST REPRESENTATE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORZED OR WARRANTED FOR USE N MLTARY, AR CRAFT, SPACE, LFE SANG, OR LFE SUSTANNG APPLCATONS, NOR N PRODUCTS OR SYSTEMS WHERE FALURE OR MALFUNCTON MAY RESULT N PERSONAL NJURY, DEATH, OR SEERE PROPERTY OR ENRONMENTAL DAMAGE. ST PRODUCTS WHCH ARE NOT SPECFED AS "AUTOMOTE GRADE" MAY ONLY BE USED N AUTOMOTE APPLCATONS AT USER S OWN RSK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. nformation in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 21 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - ndia - srael - taly - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America Doc D 5649 Rev 3 13/13