Circuits: Light-Up Creatures Student Advanced version
|
|
|
- Cuthbert Conley
- 5 years ago
- Views:
Transcription
1 Circuits: Light-Up Creatures Student Advanced version In this lab you will explore current, voltage and resistance and their relationships as given by the Ohm s law. You will also explore of how resistance can be arranged within circuits as well as be exposed to the concept of power. Part I: Resistance- Series and Parallel combinations There are different ways in which we can set different resistances across our circuits. Two ways of combining resistors, which are electrical components with known values of resistance, are: 1) in series, and 2) in parallel. 1) Resistors are said to be in series if they are placed one after another in a circuit as shown in the diagram below: Resistor 1 Resistor 2 The same amount of current, I, flows through each resistor, but the total voltage, V, supplied from the battery gets divided amongst the two resistors. Total Resistance, R T (Ω) = R 1 (Ω) + R 2 (Ω) 2) Resistors are said to be in parallel if they are arranged such that all resistors in parallel receive the same voltage with different amounts of current flowing through each of them, as shown below: Resistor 1 Resistor 2 Tungsten bulbs are used as resistors in this experiment.
2 3) Measure the resistance of each of the two bulbs provided. In order to do this, turn your multimeter dial setting to 200 Ω range as shown in the picture below: Connecting leads Attach the positive and negative terminal leads (silver metallic parts at the end of multimeter connecting wires) to two different connecting wires with crocodile clips. Attach the remaining free crocodile clips to either metallic attachments on the bulb. Record the resistance reading from the multimeter display. Bulb 1 resistance Ω Bulb 2 resistance Ω Q1. Predict total resistance of the two bulbs if placed in series in a circuit. Q2. Now predict the total resistance with the bulbs in parallel. Q3. Which of the two arrangements of bulbs do you think will give a higher resistance?
3 4) Setup the circuit with the light bulbs in series and measure the total resistance of the bulbs using the multimeter. Total resistance of bulbs in series Ω 5) Setup the circuit with the light bulbs in parallel and measure the total resistance of the bulbs using the multimeter. Total resistance of bulbs in parallel Ω Q4. Which arrangements of the bulbs gives a higher resistance? Does your measurement agree with the predicted results? Part II: Ohm s Law- Relationship of Current (I), Voltage (V) and Resistance (R) Ohm s law states that V=I*R, i.e. I is directly proportional to V, and inversely proportional to R. Direct proportionality means that when V increases, I is expected to increase with a constant ratio. Inverse proportionality means that when R increases, I is expected to decrease by a constant ratio. 1) Set up the following circuit and observe the brightness of the bulb when lighted using three 1.5V batteries and six 1.5V batteries. Measure the current flowing through the bulb in both cases using the multimeter. Circuit 1 Circuit 2 TotalVoltageCircuit1 = 3 1.5V = 4.5V TotalVoltageCircuit2 = 6 1.5V = 9V
4 Current through circuit with 3 batteries Amps Current through circuit with 6 batteries Amps Q5. Which battery arrangement gave a higher current reading, three or six? Q6. Calculate the ratio of voltage to current for both circuits. What does this number represent? 2) Set up the two bulbs in series as was done in part one and connect the free end of one of the connecting wires to the negative terminal of a battery in series with five other batteries. Attach the other free end to the negative lead of the multimeter set at 10 Ω range. Take another connecting wire and attached the positive lead of multimeter to the positive terminal of the battery series. Record the current reading. A Current through circuit in series Amps
5 3) Repeat step 2 for circuit in which the bulbs are arranged in parallel. Read current flowing through each of two bulbs and record observations. A Current through circuit in parallel Amps Q7. Which resistor arrangement gave the higher current reading? Q8. What does this tell us about the relationship of current with respect to the resistance? Q9. Find the ratio of voltage to current for each resistor arrangement. What does the ratio represent?
Circuits: Light-Up Creatures Teacher version
Circuits: Light-Up Creatures Teacher version In this lab you will explore current, voltage and resistance and their relationships as given by the Ohm s law. You will also explore of how resistance can
General Department PHYSICS LABORATORY APHY 112 EXPERIMENT 2: OHMS LAW. Student s name... Course Semester. Year.Reg.No
General Department PHYSICS LABORATORY APHY 112 EXPERIMENT 2: OHMS LAW Student s name... Course Semester. Year.Reg.No FREDERICK UNIVERSITY 1 EXPERIMENT 3 OHMS LAW Equipment needed Equipment needed Circuits
Simple Circuits Experiment
Physics 8.02T 1 Fall 2001 Simple Circuits Experiment Introduction Our world is filled with devices that contain electrical circuits in which various voltage sources cause currents to flow. We use radios,
VISUAL PHYSICS ONLINE. Experiment PA41A ELECTRIC CIRCUITS
VISUAL PHYSICS ONLINE Experiment PA41A ELECTRIC CIRCUITS Equipment (see Appendices) 12V DC power supply (battery): multimeter (and/or milliammeter and voltmeter); electrical leads; alligator clips; fixed
Current, resistance, and Ohm s law
Current, resistance, and Ohm s law Apparatus DC voltage source set of alligator clips 2 pairs of red and black banana clips 3 round bulb 2 bulb sockets 2 battery holders or 1 two-battery holder 2 1.5V
Lab 3 DC CIRCUITS AND OHM'S LAW
43 Name Date Partners Lab 3 DC CIRCUITS AND OHM'S LAW AMPS + - VOLTS OBJECTIVES To learn to apply the concept of potential difference (voltage) to explain the action of a battery in a circuit. To understand
Exercise 3: Ohm s Law Circuit Voltage
Ohm s Law DC Fundamentals Exercise 3: Ohm s Law Circuit Voltage EXERCISE OBJECTIVE When you have completed this exercise, you will be able to determine voltage by using Ohm s law. You will verify your
Ohm's Law and the Measurement of Resistance
Ohm's Law and the Measurement of Resistance I. INTRODUCTION An electric current flows through a conductor when a potential difference is placed across its ends. The potential difference is generally in
Exercise 2: Ohm s Law Circuit Current
Exercise 2: Circuit Current EXERCISE OBJECTIVE When you have completed this exercise, you will be able to determine current by using Ohm s law. You will verify your results with a multimeter. DISCUSSION
Pre-LAB 5 Assignment
Name: Lab Partners: Date: Pre-LA 5 Assignment Fundamentals of Circuits III: Voltage & Ohm s Law (Due at the beginning of lab) Directions: Read over the Lab Fundamentals of Circuits III: Voltages :w & Ohm
Physics 1051 Laboratory #4 DC Circuits and Ohm s Law. DC Circuits and Ohm s Law
DC Circuits and Ohm s Law Contents Part I: Objective Part II: Introduction Part III: Apparatus and Setup Part IV: Measurements Part V: Analysis Part VI: Summary and Conclusions Part I: Objective In this
Resistance and Ohm s Law R V I. 1 ohm = 1 volt ampere
Resistance and Ohm s Law If you maintain an electric potential difference, or voltage V, across any conductor, an electric current occurs. In general, the magnitude of the current depends on the potential
ExamLearn.ie. Current Electricity
ExamLearn.ie Current Electricity Current Electricity An electric current is a flow of electric charge. If a battery is connected to each end of a conductor, the positive terminal will attract the free
Series and Parallel Resistors
Series and Parallel Resistors Today you will investigate how connecting resistors in series and in parallel affects the properties of a circuit. You will assemble several circuits and measure the voltage
ELECTRIC CIRCUIT PROBLEMS 12 AUGUST 2014
ELECTRIC CIRCUIT PROBLEMS 12 AUGUST 2014 In this lesson we: Lesson Description Discuss the application of Ohm s Law Explain the series and parallel connection of resistors Discuss the effect of internal
Series and parallel resistances
Series and parallel resistances Objectives Calculate the equivalent resistance for resistors connected in both series and parallel combinations. Construct series and parallel circuits of lamps (resistors).
Pre-Lab for Batteries and Bulbs
Pre-Lab for Batteries and Bulbs Complex circuits composed of resistors can be simplified by using the concept of equivalent resistors. For example if resistors R 1, R 2, and R 3 are connected in series,
Unit 7 Parallel Circuits
Unit 7 Parallel Circuits Objectives: Unit 7 Parallel Circuits Discuss the characteristics of parallel circuits. State the three rules for solving electrical values of resistance for parallel circuits.
DC CIRCUITS AND OHM'S LAW
July 15, 2008 DC Circuits and Ohm s Law 1 Name Date Partners DC CIRCUITS AND OHM'S LAW AMPS - VOLTS OBJECTIVES OVERVIEW To learn to apply the concept of potential difference (voltage) to explain the action
Lab 4 Ohm s Law and Resistors
` Lab 4 Ohm s Law and Resistors What You Need To Know: The Physics One of the things that students have a difficult time with when they first learn about circuits is the electronics lingo. The lingo and
Module 1, Lesson 2 Introduction to electricity. Student. 45 minutes
Module 1, Lesson 2 Introduction to electricity 45 minutes Student Purpose of this lesson Explanations of fundamental quantities of electrical circuits, including voltage, current and resistance. Use a
Lab. 1: Simple Linear Circuit Analysis
Lab. 1: Simple Linear Circuit Analysis Philippe Piot (February 9th, 27) 1. Ohm's Law The circuit shown in Figure 1 was built with resistance R=1 and then 1 kω. For these two values of the resistance, the
Period 12 Activity Sheet Solutions: Electric Circuits
Period 2 Activity Sheet Solutions: Electric Circuits Activity 2.: How are Voltage, Current, and Resistance Related? a) Data Collection Connect the DC power supply to the thin 30 cm length of nichrome wire.
Lab 4 OHM S LAW AND KIRCHHOFF S CIRCUIT RULES
57 Name Date Partners Lab 4 OHM S LAW AND KIRCHHOFF S CIRCUIT RULES AMPS - VOLTS OBJECTIVES To learn to apply the concept of potential difference (voltage) to explain the action of a battery in a circuit.
Ohm's Law and DC Circuits
Physics Lab II Ohm s Law Name: Partner: Partner: Partner: Ohm's Law and DC Circuits EQUIPMENT NEEDED: Circuits Experiment Board Two Dcell Batteries Wire leads Multimeter 100, 330, 560, 1k, 10k, 100k, 220k
Electricity Transition Questions Applied General in Science
Electricity Transition Questions Applied General in Science Marks: 62 marks Pass = 30% Comments: Merit = 45% Distinction = 65% Name: Teacher: MDS Date: Q1. (a) Draw one line from each circuit symbol to
Chapter 12 Electric Circuits
Conceptual Physics/ PEP Name: Date: Chapter 12 Electric Circuits Section Review 12.1 1. List one way electric current is similar to water current and one way it is different. 2. Draw a circuit diagram
II. Experimental Procedure
Ph 122 July 27, 2006 Ohm's Law http://www.physics.sfsu.edu/~manuals/ph122/ I. Theory In this lab we will make detailed measurements on one resistor to see if it obeys Ohm's law. We will also verify the
These are samples of learning materials and may not necessarily be exactly the same as those in the actual course. Contents 1.
Contents These are samples of learning materials and may not necessarily be exactly the same as those in the actual course. Contents 1 Introduction 2 Ohm s law relationships 3 The Ohm s law equation 4
Activity Electrical Circuits Simulation
Activity 1.2.3 Electrical Circuits Simulation Introduction Since the late 1800s, engineers have designed systems to utilize electrical energy due to its ability to be converted, stored, transmitted, and
Ohm s Law and Electrical Circuits
Ohm s Law and Electrical Circuits INTRODUCTION In this experiment, you will measure the current-voltage characteristics of a resistor and check to see if the resistor satisfies Ohm s law. In the process
Activity Electrical Circuits Simulation
Activity 1.2.3 Electrical Circuits Simulation Introduction Since the late 1800s, engineers have designed systems to utilize electrical energy due to its ability to be converted, stored, transmitted, and
RESISTANCE IN WIRES 4) 4R
RESISTANCE IN WIRES NAME: 1. A copper wire of length L and cross-sectional area A has resistance R. A second copper wire at the same temperature has a length of 2L and a cross-sectional area of 1 2A. What
Exercise 2: Current in a Series Resistive Circuit
DC Fundamentals Series Resistive Circuits Exercise 2: Current in a Series Resistive Circuit EXERCISE OBJECTIVE circuit by using a formula. You will verify your results with a multimeter. DISCUSSION Electric
Experiment 9: Electrical Measurements
xperiment 9: lectrical Measurements 1. Obtain 3 batteries with holders, 2 identical flashlight bulbs with holders, leads (wires) with alligator clips, and a multimeter. 2. Using the Multimeter a. There
Lightbulbs and Dimmer Switches: DC Circuits
Introduction It is truly amazing how much we rely on electricity, and especially on devices operated off of DC current. Your PDA, cell phone, laptop computer and calculator are all examples of DC electronics.
Experiment 1: Circuits Experiment Board
01205892C AC/DC Electronics Laboratory Experiment 1: Circuits Experiment Board EQUIPMENT NEEDED: AC/DC Electronics Lab Board: Wire Leads Dcell Battery Graph Paper Purpose The purpose of this lab is to
Ohm s Law. Equipment. Setup
rev 05/2018 Ohm s Law Equipment Qty Item Part Number 1 AC/DC Electronics Laboratory EM-8656 1 Current Sensor CI-6556 1 Multimeter 4 Patch Cords 2 Banana Clips 1 100Ω Resistor Purpose The purpose of this
DC Electric Circuits: Resistance and Ohm s Law
DC Electric Circuits: Resistance and Ohm s Law Goals and Introduction Our society is very reliant on electric phenomena, perhaps most so on the utilization of electric circuits. For much of our world to
Book page Syllabus 2.8, 2.9, Series and parallel circuits
Book page 77 79 Syllabus 2.8, 2.9, 2.14 Series and parallel circuits Find the Fib! (1) The symbol for a bulb is (2) In a parallel circuit potential difference is the same as the supply voltage on all branches.
HANDS-ON ACTIVITY 4 BUILDING SERIES AND PARALLEL CIRCUITS BACKGROUND WIRING DIRECTIONS
ACTIVITY 4 BUILDING SERIES AND PARALLEL CIRCUITS BACKGROUND Make sure you read the background in Activity 3 before doing this activity. WIRING DIRECTIONS Materials per group of two: one or two D-cells
Resistance and Ohm s law
Resistance and Ohm s law Objectives Characterize materials as conductors or insulators based on their electrical properties. State and apply Ohm s law to calculate current, voltage or resistance in an
Configurations of Resistors
Configurations of Resistors Safety and Equipment Multimeter with probes or banana leads. Two of 50Ω and one of 100Ω resistors 5 connecting wires with double alligator clips Introduction There are two basic
Born: March 16, 1789, Erlangen, Germany Died: July 6, 1854, Munich, Germany Education: University of Erlangen-Nuremberg
Ohm s Law Georg Simon Ohm was a German physicist and mathematician. As a school teacher, Ohm began his research with the new electrochemical cell, invented by Italian scientist Alessandro Volta. Born:
Vocabulary. Electric Current. Electric Circuit. Open Circuit. Conductors. Insulators. Ohm s Law Current. Voltage. Resistance.
Vocabulary Term Electric Current Definition Electric Circuit Open Circuit Conductors Insulators Ohm s Law Current Voltage Resistance Electrical Power Series Circuit Parallel Circuit Page 1 Symbols Used
PHY 132 LAB : Ohm s Law
PHY 132 LAB : Ohm s Law Introduction: In this lab, we look at the concepts of electrical resistance and resistivity. Text Reference: Wolfson 27:2-3. Special equipment notes: 1. Note the tips on wiring
Series and Parallel DC Circuits
Series and Parallel DC Circuits asic Circuits n electric circuit is closed loop of conductive material (metal wire) that connects several circuit elements together (batteries, resistors, capacitors, etc.)
Circuits. Ch. 35 in your text book
Circuits Ch. 35 in your text book Objectives Students will be able to: 1) Draw schematic symbols for electrical circuit components 2) Calculate the equivalent resistance for a series circuit 3) Calculate
PH213 Chapter 26 solutions
PH213 Chapter 26 solutions 26.6. IDENTIFY: The potential drop is the same across the resistors in parallel, and the current into the parallel combination is the same as the current through the 45.0-Ω resistor.
A piece of wire of resistance R is cut into five equal parts. These parts are then connected in
Page 221»Exercise» Question 1: A piece of wire of resistance R is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination is R', then the
Chapters 35: Electric Circuits
Text: Chapter 35 Think and Explain: 1-10 Think and Solve: 1-4 Chapters 35: Electric Circuits NME: Vocabulary: ammeter, voltmeter, series, parallel, equivalent resistance, circuit, short circuit, open circuit
EET 1150 Lab 6 Ohm s Law
Name EQUIPMENT and COMPONENTS Digital Multimeter Trainer with Breadboard Resistors: 220, 1 k, 1.2 k, 2.2 k, 3.3 k, 4.7 k, 6.8 k Red light-emitting diode (LED) EET 1150 Lab 6 Ohm s Law In this lab you ll
PHYS 1402 General Physics II Experiment 5: Ohm s Law
PHYS 1402 General Physics II Experiment 5: Ohm s Law Student Name Objective: To investigate the relationship between current and resistance for ordinary conductors known as ohmic conductors. Theory: For
Ohm s and Kirchhoff s Circuit Laws. Abstract. Introduction and Theory. EE 101 Spring 2006 Date: Lab Section #: Lab #2
EE 101 Spring 2006 Date: Lab Section #: Lab #2 Name: Ohm s and Kirchhoff s Circuit Laws Abstract Rev. 20051222JPB Partner: Electrical circuits can be described with mathematical expressions. In fact, it
Introduction to the Laboratory
Memorial University of Newfoundland Department of Physics and Physical Oceanography Physics 2055 Laboratory Introduction to the Laboratory The purpose of this lab is to introduce you to some of the equipment
Episode 108: Resistance
Episode 108: Resistance The idea of resistance should be familiar (although perhaps not secure) from pre-16 science course, so there is no point pretending that this is an entirely new concept. A better
Ohm s Law. 1 Object. 2 Apparatus. 3 Theory. To study resistors, Ohm s law, linear behavior, and non-linear behavior.
Ohm s Law Object To study resistors, Ohm s law, linear behavior, and non-linear behavior. pparatus esistors, power supply, meters, wires, and alligator clips. Theory resistor is a circuit element which
Bell Ringer: Define to the best of your ability the definition of: Current Voltage Resistance
Bell Ringer: Define to the best of your ability the definition of: Current Voltage Resistance Explain the behavior of the current and the voltage in a Series Circuit. Explain the behavior of the current
THE BREADBOARD; DC POWER SUPPLY; RESISTANCE OF METERS; NODE VOLTAGES AND EQUIVALENT RESISTANCE; THÉVENIN EQUIVALENT CIRCUIT
THE BREADBOARD; DC POWER SUPPLY; RESISTANCE OF METERS; NODE VOLTAGES AND EQUIVALENT RESISTANCE; THÉVENIN EQUIVALENT CIRCUIT YOUR NAME GTA S SIGNATURE LAB MEETING TIME Objectives: To correctly operate the
Simple Electrical Circuits
rev 05/2018 Simple Electrical Circuits Equipment Qty Item Part Number 1 AC/DC Electronics Laboratory EM-8656 1 Voltage Sensor UI-5100 1 Current Sensor CI-6556 1 Multimeter 4 Patch Cords 2 Banana Clips
Chabot College Physics Lab Ohm s Law & Simple Circuits Scott Hildreth
Chabot College Physics Lab Ohm s Law & Simple Circuits Scott Hildreth Goals: Learn how to make simple circuits, measuring resistances, currents, and voltages across components. Become more comfortable
ENGR 1181 Lab 3: Circuits
ENGR 1181 Lab 3: Circuits - - Lab Procedure - Report Guidelines 2 Overview of Circuits Lab: The Circuits Lab introduces basic concepts of electric circuits such as series and parallel circuit, used in
Ohm s Law. 1 Object. 2 Apparatus. 3 Theory. To study resistors, Ohm s law, linear behavior, and non-linear behavior.
Ohm s Law Object To study resistors, Ohm s law, linear behavior, and non-linear behavior. pparatus esistors, power supply, meters, wires, and alligator clips. Theory resistor is a circuit element which
EE 448 Fall Lab Experiment No. 3 04/04/2008. Transformer Experiment
EE 8 Laboratory Experiment 3 EE 8 Fall 2008 Lab Experiment No. 3 0/0/2008 1 I. INTRODUCTION OBJECTIVES: EE 8 Laboratory Experiment 3 1. To learn how real world transformers operate under ideal conditions.
LAB 2 Circuit Tools and Voltage Waveforms
LAB 2 Circuit Tools and Voltage Waveforms OBJECTIVES 1. Become familiar with a DC power supply and setting the output voltage. 2. Learn how to measure voltages & currents using a Digital Multimeter. 3.
V (in volts) = voltage applied to the circuit, I (in amperes) = current flowing in the circuit, R (in ohms) = resistance of the circuit.
OHM S LW OBJECTIES: PRT : 1) Become familiar with the use of ammeters and voltmeters to measure DC voltage and current. 2) Learn to use wires and a breadboard to build circuits from a circuit diagram.
DC Circuits PHYS 501 Homework 2
DC Circuits PHYS 501 Homework 2 NAME: (partner if any: ) In-class Laboratory. Worth 12 points. A "circuit" is a circular (completed) path from the red or "+" side of a voltage source through various "circuit
Kirchhoff s laws. Objectives. Assessment. Assessment. Assessment. Assessment 5/27/14. Apply Kirchhoff s first and second laws.
Kirchhoff s laws Objectives Apply Kirchhoff s first and second laws. Calculate the current and voltage for resistor circuits connected in parallel. Calculate the current and voltage for resistor circuits
Using Voltage Dividers to Design a Photo-Sensitive LED Circuit. ( Doug Oliver & Jackie Kane. May be reproduced for non-profit classroom use.
Using Voltage Dividers to Design a Photo-Sensitive LED Circuit ( 2009 - Doug Oliver & Jackie Kane. May be reproduced for non-profit classroom use.) Purpose: After completing the module students will: 1.
Experiment 3. Ohm s Law. Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current.
Experiment 3 Ohm s Law 3.1 Objectives Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current. Construct a circuit using resistors, wires and a breadboard
Problem Solving 7: Building Simple Circuits using PhET Interactive Simulation 1
MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Physics Problem Solving 7: Building Simple Circuits using PhET Interactive Simulation 1 Section Table and Group Names Hand in one copy per group at the
Experiment 2. Ohm s Law. Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current.
Experiment 2 Ohm s Law 2.1 Objectives Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current. Construct a circuit using resistors, wires and a breadboard
Ch. 18 and 19 Review Problems 2
Ch. 18 and 19 Review Problems 2 NAME 1) A device that produces electricity by transforming chemical energy into electrical energy is called a A) generator. B) transformer. C) battery. D) none of the given
Experiment P-24 Circuits and Series Resistance
1 Experiment P-24 Circuits and Series Resistance Objectives To study the relationship between the voltage applied to a given resistor and the intensity of the current running through it. Modules and Sensors
Electrical Measurements
Electrical Measurements INTRODUCTION In this section, electrical measurements will be discussed. This will be done by using simple experiments that introduce a DC power supply, a multimeter, and a simplified
Lab 9 - INTRODUCTION TO AC CURRENTS AND VOLTAGES
145 Name Date Partners Lab 9 INTRODUCTION TO AC CURRENTS AND VOLTAGES V(volts) t(s) OBJECTIVES To learn the meanings of peak voltage and frequency for AC signals. To observe the behavior of resistors in
Exercise 3: Voltage in a Series Resistive Circuit
DC Fundamentals Series Resistive Circuits Exercise 3: Voltage in a Series Resistive Circuit EXERCISE OBJECTIVE When you have completed this exercise, you will be able to determine the voltage in a series
+ A Supply B. C Load D
17 E7 E7.1 OHM'S LAW AND RESISTANCE NETWORKS OBJECT The objects of this experiment are to determine the voltage-current relationship for a resistor and to verify the series and parallel resistance formulae.
DC Circuits. (a) You drag an element by clicking on the body of the element and dragging it.
DC Circuits KET Virtual Physics Labs Worksheet Lab 12-1 As you work through the steps in the lab procedure, record your experimental values and the results on this worksheet. Use the exact values you record
Chapter 21 Electric Current and Direct-Current Circuit
Chapter 21 Electric Current and Direct-Current Circuit Outline 21-1 Electric Current 21-2 Resistance and Ohm s Law 21-3 Energy and Power in Electric Circuit 21-4 Resistance in Series and Parallel 21-5
1 A 60-W light bulb operating on a 120-volt household circuit has a resistance closest to
Slide 1 / 31 1 A 60-W light bulb operating on a 120-volt household circuit has a resistance closest to A 60 Ω B 120 Ω C 240 Ω D 180 Ω E 360 Ω Slide 2 / 31 2 Which of the following is equivalent to the
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 7 LAMPS OBJECTIVES The purpose of this experiment is to introduce the concept of resistance change
Activity P51: LR Circuit (Power Output, Voltage Sensor)
Activity P51: LR Circuit (Power Output, Voltage Sensor) Concept DataStudio ScienceWorkshop (Mac) ScienceWorkshop (Win) Circuits P51 LR Circuit.DS (See end of activity) (See end of activity) Equipment Needed
Experiment P-10 Ohm's Law
1 Experiment P-10 Ohm's Law Objectives To study the relationship between the voltage applied to a given resistor and the intensity of the current running through it. Modules and Sensors PC + NeuLog application
Experiment 4 Topic: Solar Panels Week A Procedure
Experiment 4 Topic: Solar Panels Week A Procedure Laboratory Assistant: Email: Office/Hours E-4 Website: Shirui Luo Sluo1@nd.edu 12/03 12/06 from 5:00 pm to 6:00 pm in Fitzpatrick B14 http://www.nd.edu/~jott/measurements_lab/e4/
(%) ex Blue-Black-Brown-Gold 600 Ω ± 5% ± 30 1
** Disclaimer: This Lab is not to be copied, duplicated, and/or distributed, in whole or in part, unless approval is received from the University of Colorado at Colorado Springs Physics Department AND
EET 150 Introduction to EET Lab Activity 1 Resistor Color Codes and Resistor Value Measurement
Required Parts, Software and Equipment Parts 20 assorted 1/4 watt resistors 5% tolerance Equipment Required Solderless Experimenters' Board Digital Multimeter Optional Alligator clip leads hookup wire
Lab 5: Real DC Circuits
Physics 2020, Fall 2010 Lab 5 page 1 of 7 Circle your lab day and time. Your name: Mon Tue Wed Thu Fri TA name: 8-10 10-12 12-2 2-4 4-6 INTRODUCTION Lab 5: Real DC Circuits The field of electronics has
Chapter 1: DC circuit basics
Chapter 1: DC circuit basics Overview Electrical circuit design depends first and foremost on understanding the basic quantities used for describing electricity: Voltage, current, and power. In the simplest
Unit 8 Combination Circuits
Unit 8 Combination Circuits Objectives: Define a combination circuit. List the rules for parallel circuits. List the rules for series circuits. Solve for combination circuit values. Characteristics There
Basic DC Power Supply
Basic DC Power Supply Equipment: 1. Analog Oscilloscope 2. Digital multimeter 3. Experimental board and connectors. Objectives: 1. To understand the basic DC power supply both half wave and full wave rectifier.
1 V = IR P = IV R eq. 1 R i. = R i. = R eq. V = Energy Q. I = Q t
Chapters 34 & 35: Electric Circuits NAME: Text: Chapter 34 Chapter 35 Think and Explain: 1-3, 6-8, 10 Think and Explain: 1-10 Think and Solve: 1-6 Think and Solve: 1-4 Vocabulary: Ohm s Law, resistance,
PHYSICS 221 LAB #6: CAPACITORS AND AC CIRCUITS
Name: Partners: PHYSICS 221 LAB #6: CAPACITORS AND AC CIRCUITS The electricity produced for use in homes and industry is made by rotating coils of wire in a magnetic field, which results in alternating
Basic Circuits. PC1222 Fundamentals of Physics II. 1 Objectives. 2 Equipment List. 3 Theory
PC1222 Fundamentals of Physics II Basic Circuits 1 Objectives Investigate the relationship among three variables (resistance, current and voltage) in direct current circuits. Investigate the behaviours
Downloaded from
Question 1: What does an electric circuit mean? An electric circuit consists of electric devices, switching devices, source of electricity, etc. that are connected by conducting wires. Question 2: Define
Electric Circuits. Physics 6 th Six Weeks
Electric Circuits Physics 6 th Six Weeks Electric Circuits (a review) A circuit is a path through which electricity can flow Electric Circuits always contain 3 things: a voltage source, a conductor (usually
Lab 06: Ohm s Law and Servo Motor Control
CS281: Computer Systems Lab 06: Ohm s Law and Servo Motor Control The main purpose of this lab is to build a servo motor control circuit. As with prior labs, there will be some exploratory sections designed
Introduction to Engineering ENGR Electrical Engineering. Dr. Coates
Introduction to Engineering ENG 1100 - Electrical Engineering Dr. Coates Branches of Electrical Engineering Circuits/Microelectronics Communications Computer Hardware and Software, Digital Logic, Microprocessor
Lab 11: Circuits. Figure 1: A hydroelectric dam system.
Description Lab 11: Circuits In this lab, you will study voltage, current, and resistance. You will learn the basics of designing circuits and you will explore how to find the total resistance of a circuit
ANSWERS AND MARK SCHEMES. (a) 3 A / 2 1 = 1.5 A 1. (b) 6 V 1. (c) resistance = V / I 1 = 6 / (b) I = V / R 1 = 3 / 15 1 = 0.
QUESTIONSHEET (a) 3 A / 2 =.5 A (b) 6 V (c) resistance = V / I = 6 /.5 = 4 Ω QUESTIONSHEET 2 TOTAL / 6 (a) 5 Ω + 0 Ω = 5 Ω (b) I = V / R = 3 / 5 = 0.2 A Units are essential in calculations. Sometimes eamination