EET 150 Introduction to EET Lab Activity 1 Resistor Color Codes and Resistor Value Measurement
|
|
|
- Agnes Skinner
- 6 years ago
- Views:
Transcription
1 Required Parts, Software and Equipment Parts 20 assorted 1/4 watt resistors 5% tolerance Equipment Required Solderless Experimenters' Board Digital Multimeter Optional Alligator clip leads hookup wire Software MS Word Fall Lab1_ET510.docx
2 Introduction Many electrical circuits contain multiple variations of resistor networks. Resistors play a vital role in the distribution and limiting of electric current in a circuit. Students must learn to identify and measure the values of these components to effectively design and troubleshoot electrical and electronic circuits. Each resistor has three to five colored bands on them that represent different values. Reading and decoding these bands allows you to determine a resistor s value and accuracy. The figure below shows the three and four band resistor color codes. Five percent tolerance resistors use the three band code on the top of the diagram. Figure 1. Three and Four Band Resistor Color Codes. The first two or three bands determine the significant digits based on the resistor accuracy. High accuracy resistors use three bands while standard accuracy resistors use two bands. The next band is the multiplier of the significant digits. The last band is the tolerance. The tolerance is a percentage that determines the expected range of resistance values based on the marked value. The following equation shows how to compute the range of expected resistance values for a known marked value. Fall Lab1_ET510.docx
3 R R R R n n 1 1 T 100 T 100 Where: R + = Marked resistance plus the tolerance R - = Marked resistance minus the tolerance R n = marked value or the resistor T = tolerance in percent Another way to identify the value of a resistor is to use a multimeter to measure its resistance. The multimeter passes a known amount of current to through its leads. The meter then measures the voltage drop across the resistor being tested and calculates the resistance using Ohm s Law. Lab Objective The objective of this lab is to give students the opportunity to familiarize themselves with digital multimeters, resistance measurement, and the resistor color code. When the lab is completed, the student will be able to use a multimeter to measure the value of a resistor and identify its value from its color code. Procedure 1. Place twenty given resistors on your breadboard. Make sure that there is only one resistor per row and that each leg of the resistor is in a separate row. See figure below for proper resistor placement. 2. Write down the resistor band colors for each of the resistors in the table. 3. Using the color codes determine the components theoretical resistance. Fall Lab1_ET510.docx
4 4. Turn on the multimeter, set the machine to measure resistance, and hook the leads up to the machine. View the provided course videos to see how to use this instrument. 5. Use your multimeter to measure the actual values of the resistors. Record these values in the table. 6. After steps one through five have been completed return the resistors to storage. Return the multimeter and its leads to their proper spot. 7. Fill in the rest of the table that is provided. Use the formulas provided to compute the acceptable range for the measured resistance values. Discussion Points: These are points that should be included in your lab report. What is the significance of the colored bands on resistors? How does a multi-meter measure resistance? Why should you not hold the resistor while measuring its resistance? What happens to current when resistance is increased? Fall Lab1_ET510.docx
5 Color Abbreviations BL = Black G = Green G = Gold BN = Brown BU = Blue S = Silver R = Red V = Violet O = Orange GR = Grey Y = Yellow W = White Table 1 Resistor Color Codes and Measurements Band 1 Band 2 Band 3 Band 4 Theoretical value R Plus Tolerance R Minus Tolerance Measured Value Fall Lab1_ET510.docx
Aim: To learn the resistor color codes and building a circuit on a BreadBoard. Equipment required: Resistances, millimeter, power supply
Understanding the different components Aim: To learn the resistor color codes and building a circuit on a BreadBoard Equipment required: Resistances, millimeter, power supply Resistors are color coded
II. Experimental Procedure
Ph 122 July 27, 2006 Ohm's Law http://www.physics.sfsu.edu/~manuals/ph122/ I. Theory In this lab we will make detailed measurements on one resistor to see if it obeys Ohm's law. We will also verify the
DEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 03. Resistors
MEHRAN UNIVERSITY OF ENGINEERING AND TECHNOLOGY, JAMSHORO DEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 03 Resistors Roll. No: Checked by: Date: Grade: Object: To become familiar with resistors,
Ohm's Law and DC Circuits
Physics Lab II Ohm s Law Name: Partner: Partner: Partner: Ohm's Law and DC Circuits EQUIPMENT NEEDED: Circuits Experiment Board Two Dcell Batteries Wire leads Multimeter 100, 330, 560, 1k, 10k, 100k, 220k
EGR 101 LABORATORY 1 APPLICATION OF ALGEBRA IN ENGINEERING Wright State University
EGR 101 LABORATORY 1 APPLCATON OF ALGEBRA N ENGNEERNG Wright State University OBJECTVE: The objective of this laboratory is to illustrate applications of algebra (lines and quadratics) in engineering.
Materials: resistors: (5) 1 kω, (4) 2 kω, 2.2 kω, 3 kω, 3.9 kω digital multimeter (DMM) power supply w/ leads breadboard, jumper wires
Lab 6: Electrical Engineering Technology References: 1. Resistor (electronic) color code: http://en.wikipedia.org/wiki/electronic_color_code 2. Resistor color code tutorial: http://www.michaels-electronics-lessons.com/resistor-color-code.html
Introduction to the Laboratory
Memorial University of Newfoundland Department of Physics and Physical Oceanography Physics 2055 Laboratory Introduction to the Laboratory The purpose of this lab is to introduce you to some of the equipment
Experiment 3 Ohm s Law
Experiment 3 Ohm s Law The goals of Experiment 3 are: To identify resistors based upon their color code. To construct a two-resistor circuit using proper wiring techniques. To measure the DC voltages and
1-1. Kirchoff s Laws A. Construct the circuit shown below. R 1 =1 kω. = 2.7 kω R 3 R 2 5 V
Physics 310 Lab 1: DC Circuits Equipment: Digital Multimeter, 5V Supply, Breadboard, two 1 kω, 2.7 kω, 5.1 kω, 10 kω, two, Decade Resistor Box, potentiometer, 10 kω Thermistor, Multimeter Owner s Manual
Inductors and Transformers
MEHRAN UNIVERSITY OF ENGINEERING AND TECHNOLOGY, JAMSHORO DEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 05 Inductors and Transformers Roll. No: Checked by: Date: Grade: Object: To become familiar
Tutorial Using a multimeter
Tutorial Using a multimeter The multimeter You might have already seen or worked with a multimeter. It is an electronic measuring device that combines several instruments such as the voltmeter (to measure
OHM'S LAW AND RESISTANCE NETWORKS OBJECT
17 E7 E7.1 OHM'S LAW AND RESISTANCE NETWORKS OBJECT The objects of this experiment are to determine the voltage-current relationship for a resistor and to verify the series and parallel resistance formulae.
I. Objectives Upon completion of this experiment, the student should be able to: Ohm s Law
EENG-201 Experiment # 1 Series Circuit and Parallel Circuits I. Objectives Upon completion of this experiment, the student should be able to: 1. ead and use the resistor color code. 2. Use the digital
EET140/3 ELECTRIC CIRCUIT I
SCHOOL OF ELECTRICAL SYSTEM ENGINEERING UNIVERSITI MALAYSIA PERLIS EET140/3 ELECTRIC CIRCUIT I MODULE 1 PART I: INTRODUCTION TO BASIC LABORATORY EQUIPMENT PART II: OHM S LAW PART III: SERIES PARALEL CIRCUIT
General Lab Notebook instructions (from syllabus)
Physics 310 Lab 1: DC Circuits Equipment: Digital Multimeter, 5V Supply, Breadboard, two 1 k, 2.7 k, 5.1 k, 10 k, two Decade Resistor Box, potentiometer, 10 k Thermistor, Multimeter Owner s Manual General
Resistance. Department of Physics & Astronomy Texas Christian University, Fort Worth, TX. April 23, 2013
Resistance Department of Physics & Astronomy Texas Christian University, Fort Worth, TX April 23, 2013 1 Introduction Electrical resistance is a measure of how much an object opposes (or resists) the flow
Breadboard Primer. Experience. Objective. No previous electronics experience is required.
Breadboard Primer Experience No previous electronics experience is required. Figure 1: Breadboard drawing made using an open-source tool from fritzing.org Objective A solderless breadboard (or protoboard)
Introduction to Electronics. Dr. Lynn Fuller
ROCHESTER INSTITUTE OF TECHNOLOGY MICROELECTRONIC ENGINEERING Introduction to Electronics Dr. Lynn Fuller Webpage: http://www.rit.edu/~lffeee 82 Lomb Memorial Drive Rochester, NY 14623-5604 Tel (585) 475-2035
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 2 BASIC CIRCUIT ELEMENTS OBJECTIVES The purpose of this experiment is to familiarize the student with
WHEATSTONE BRIDGE. Objectives
WHEATSTONE BRIDGE Objectives The Wheatstone bridge is a circuit designed to measure an unknown resistance by comparison with other known resistances. A slide-wire form of the Wheatstone bridge will be
HANDS-ON LAB INSTRUCTION SHEETS MODULE
HANDS-ON LAB INSTRUCTION SHEETS MODULE 1 MEASURING RESISTANCE AND VOLTAGE NOTES: 1) Each student will be assigned to a unique Lab Equipment number MS01-MS30 which will match to a Tool Kit and a Radio Shack
2007 The McGraw-Hill Companies, Inc. All rights reserved.
Chapter 2 Resistors Topics Covered in Chapter 2 2-1: Types of Resistors 2-2: Resistor Color Coding 2-3: Variable Resistors 2-4: Rheostats and Potentiometers 2-5: Power Ratings of Resistors 2-6: Resistor
HANDS-ON ACTIVITY 4 BUILDING SERIES AND PARALLEL CIRCUITS BACKGROUND WIRING DIRECTIONS
ACTIVITY 4 BUILDING SERIES AND PARALLEL CIRCUITS BACKGROUND Make sure you read the background in Activity 3 before doing this activity. WIRING DIRECTIONS Materials per group of two: one or two D-cells
EK307 Introduction to the Lab
EK307 Introduction to the Lab Learning to Use the Test Equipment Laboratory Goal: Become familiar with the test equipment in the electronics laboratory (PHO105). Learning Objectives: Voltage source and
EE283 Laboratory Exercise 1-Page 1
EE283 Laboratory Exercise # Basic Circuit Concepts Objectives:. To become familiar with the DC Power Supply unit, analog and digital multi-meters, fixed and variable resistors, and the use of solderless
DC Circuits and Ohm s Law
DC Circuits and Ohm s Law INTRODUCTION During the nineteenth century so many advances were made in understanding the electrical nature of matter that it has been called the age of electricity. One such
DC Circuits and Ohm s Law
DC Circuits and Ohm s Law INTRODUCTION During the nineteenth century so many advances were made in understanding the electrical nature of matter that it has been called the age of electricity. One such
Experiment 1: Circuits Experiment Board
01205892C AC/DC Electronics Laboratory Experiment 1: Circuits Experiment Board EQUIPMENT NEEDED: AC/DC Electronics Lab Board: Wire Leads Dcell Battery Graph Paper Purpose The purpose of this lab is to
AME140 Lab #2 INTRODUCTION TO ELECTRONIC TEST EQUIPMENT AND BASIC ELECTRONICS MEASUREMENTS
INTRODUCTION TO ELECTRONIC TEST EQUIPMENT AND BASIC ELECTRONICS MEASUREMENTS The purpose of this document is to guide students through a few simple activities to increase familiarity with basic electronics
Lab 4 Ohm s Law and Resistors
` Lab 4 Ohm s Law and Resistors What You Need To Know: The Physics One of the things that students have a difficult time with when they first learn about circuits is the electronics lingo. The lingo and
Experiment 3. Ohm s Law. Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current.
Experiment 3 Ohm s Law 3.1 Objectives Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current. Construct a circuit using resistors, wires and a breadboard
Experiment 2. Ohm s Law. Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current.
Experiment 2 Ohm s Law 2.1 Objectives Become familiar with the use of a digital voltmeter and a digital ammeter to measure DC voltage and current. Construct a circuit using resistors, wires and a breadboard
Lab 3 DC CIRCUITS AND OHM'S LAW
43 Name Date Partners Lab 3 DC CIRCUITS AND OHM'S LAW AMPS + - VOLTS OBJECTIVES To learn to apply the concept of potential difference (voltage) to explain the action of a battery in a circuit. To understand
PHYS Contemporary Physics Laboratory Laboratory Exercise: LAB 01 Resistivity, Root-mean-square Voltage, Potentiometer (updated 1/25/2017)
PHYS351001 Contemporary Physics Laboratory Laboratory Exercise: LAB 01 Resistivity, Root-mean-square Voltage, Potentiometer (updated 1/25/2017) PART I: SOME FUNDAMENTAL CONCEPTS: 1. Limits on accuracy
Ohm s Law. 1 Object. 2 Apparatus. 3 Theory. To study resistors, Ohm s law, linear behavior, and non-linear behavior.
Ohm s Law Object To study resistors, Ohm s law, linear behavior, and non-linear behavior. pparatus esistors, power supply, meters, wires, and alligator clips. Theory resistor is a circuit element which
V (in volts) = voltage applied to the circuit, I (in amperes) = current flowing in the circuit, R (in ohms) = resistance of the circuit.
OHM S LW OBJECTIES: PRT : 1) Become familiar with the use of ammeters and voltmeters to measure DC voltage and current. 2) Learn to use wires and a breadboard to build circuits from a circuit diagram.
A.M. WEDNESDAY, 19 May minutes
Candidate Name Centre Number Candidate Number 0 GCSE 293/02 ELECTRONICS MODULE TEST E1 HIGHER TIER AM WEDNESDAY, 19 May 2010 45 minutes For s use Total Mark ADDITIONAL MATERIALS In addition to this examination
+ A Supply B. C Load D
17 E7 E7.1 OHM'S LAW AND RESISTANCE NETWORKS OBJECT The objects of this experiment are to determine the voltage-current relationship for a resistor and to verify the series and parallel resistance formulae.
Laboratory 2 (drawn from lab text by Alciatore)
Laboratory 2 (drawn from lab text by Alciatore) Instrument Familiarization and Basic Electrical Relations Required Components: 2 1k resistors 2 1M resistors 1 2k resistor Objectives This exercise is designed
DC CIRCUITS AND OHM'S LAW
July 15, 2008 DC Circuits and Ohm s Law 1 Name Date Partners DC CIRCUITS AND OHM'S LAW AMPS - VOLTS OBJECTIVES OVERVIEW To learn to apply the concept of potential difference (voltage) to explain the action
Oregon State University Lab Session #1 (Week 3)
Oregon State University Lab Session #1 (Week 3) ENGR 201 Electrical Fundamentals I Equipment and Resistance Winter 2016 EXPERIMENTAL LAB #1 INTRO TO EQUIPMENT & OHM S LAW This set of laboratory experiments
EET 1150 Lab 6 Ohm s Law
Name EQUIPMENT and COMPONENTS Digital Multimeter Trainer with Breadboard Resistors: 220, 1 k, 1.2 k, 2.2 k, 3.3 k, 4.7 k, 6.8 k Red light-emitting diode (LED) EET 1150 Lab 6 Ohm s Law In this lab you ll
Laboratory 2. Lab 2. Instrument Familiarization and Basic Electrical Relations. Required Components: 2 1k resistors 2 1M resistors 1 2k resistor
Laboratory 2 nstrument Familiarization and Basic Electrical Relations Required Components: 2 1k resistors 2 1M resistors 1 2k resistor 2.1 Objectives This exercise is designed to acquaint you with the
Lab 4 OHM S LAW AND KIRCHHOFF S CIRCUIT RULES
57 Name Date Partners Lab 4 OHM S LAW AND KIRCHHOFF S CIRCUIT RULES AMPS - VOLTS OBJECTIVES To learn to apply the concept of potential difference (voltage) to explain the action of a battery in a circuit.
Exercise 3: Power in a Series/Parallel Circuit
DC Fundamentals Power in DC Circuits Exercise 3: Power in a Series/Parallel Circuit EXERCISE OBJECTIVE When you have completed this exercise, you will be able to determine the power dissipated in a series/
Circuit LED 1 LED 2 A on or off on or off B on or off on or off C on or off on or off
Cornerstone Electronics Technology and Robotics Week 8 Chapter 3, Introduction to Basic Electrical Circuit Materials Continued Administration: o Prayer o Turn in quiz Review LED s: o Wire the following
Group: Names: Resistor Band Colors Measured Value ( ) R 1 : 1k R 2 : 1k R 3 : 2k R 4 : 1M R 5 : 1M
2.4 Laboratory Procedure / Summary Sheet Group: Names: (1) Select five separate resistors whose nominal values are listed below. Record the band colors for each resistor in the table below. Then connect
ECE 53A: Fundamentals of Electrical Engineering I
ECE 53A: Fundamentals of Electrical Engineering I Laboratory Assignment #1: Instrument Operation, Basic Resistor Measurements and Kirchhoff s Laws Fall 2007 General Guidelines: - Record data and observations
Resistance Measurements (Measure all of your resistors, since even those that are labeled the same can be at least a little different)
Resistors We begin by learning how to read the values of resistors and to measure the values using a digital multimeter (DMM). Resistors are the most common and simplest electrical component. In an electrical
Laboratory 3 Building and measuring circuits on the breadboard rev 1.3
1 Laboratory 3 uilding and measuring circuits on the breadboard rev 1.3 Purpose: Experiments on circuits built on a breadboard. Measurement of resistive dividers using the ohmmeter and the oscilloscope.
EE EXPERIMENT 3 RESISTIVE NETWORKS AND COMPUTATIONAL ANALYSIS INTRODUCTION
EE 2101 - EXPERIMENT 3 RESISTIVE NETWORKS AND COMPUTATIONAL ANALYSIS INTRODUCTION The resistors used in this laboratory are carbon composition resistors, consisting of graphite or some other type of carbon
Series and Parallel Resistors
Lab 8. Series and Parallel Resistors Goals To understand the fundamental difference between resistors connected in series and in parallel. To calculate the voltages and currents in simple circuits involving
Resistance and Ohm s Law
esistance and Ohm s Law Name D TA Partners Date Section Please be careful about the modes of the multimeter. When you measure a voltage, you are not allowed to use current mode (A), and vice versa. Otherwise,
THE BREADBOARD; DC POWER SUPPLY; RESISTANCE OF METERS; NODE VOLTAGES AND EQUIVALENT RESISTANCE; THÉVENIN EQUIVALENT CIRCUIT
THE BREADBOARD; DC POWER SUPPLY; RESISTANCE OF METERS; NODE VOLTAGES AND EQUIVALENT RESISTANCE; THÉVENIN EQUIVALENT CIRCUIT YOUR NAME GTA S SIGNATURE LAB MEETING TIME Objectives: To correctly operate the
Lab 2.4 Arduinos, Resistors, and Circuits
Lab 2.4 Arduinos, Resistors, and Circuits Objectives: Investigate resistors in series and parallel and Kirchoff s Law through hands-on learning Get experience using an Arduino hat you need: Arduino Kit:
DC Circuits. Date: Introduction
Group # Date: Names: DC Circuits Introduction In this experiment you will examine how to make simple DC measurements that involve current, voltage, and resistance. The current I through a resistor R with
CECS LAB 4 Prototyping Series and Parallel Resistors
NAME: POSSIBLE POINTS: 10 NAME: NAME: DIRECTIONS: We are going to step through the entire process from conceptual to a physical prototype for the following resistor circuit. STEP 1 - CALCULATIONS: Calculate
Lab 1: DC Measurements (R, V, I)
Lab 1: DC Measurements (R, V, I) Introduction Resistors are the most common component found in all electrical and electronic circuits. Resistors are found in many shapes, sizes, and values. The most common
Physics 323. Experiment # 1 - Oscilloscope and Breadboard
Physics 323 Experiment # 1 - Oscilloscope and Breadboard Introduction In order to familiarise yourself with the laboratory equipment, a few simple experiments are to be performed. References: XYZ s of
DC Circuits, Ohm's Law and Multimeters Physics 246
DC Circuits, Ohm's Law and Multimeters Physics 246 Theory: In this lab we will learn the use of multimeters, verify Ohm s law, and study series and parallel combinations of resistors and capacitors. For
Pre-Laboratory Assignment
Measurement of Electrical Resistance and Ohm's Law PreLaboratory Assignment Read carefully the entire description of the laboratory and answer the following questions based upon the material contained
San Francisco State University. School of Engineering
1 San Francisco State University School of Engineering ENGR 300 ENGR EXPERIMENATION Final Project: MULTI SOURCE CIRCUITS ANALYSIS TECHNIQUES Submitted By: Kuan Keong Austin Yiu Yin Yin Wu March 8, 2005
Name: Resistors and Basic Resistive Circuits. Objective: To gain experience with data acquisition proto-boards physical resistors. Table of Contents:
Objective: To gain experience with data acquisition proto-boards physical resistors Table of Contents: Name: Resistors and Basic Resistive Circuits Pre-Lab Assignment 1 Background 2 National Instruments
Resistance and Resistivity
Resistance and Resistivity Lab Section (circle): Day: Monday Tuesday Time: 8:00 9:30 1:10 2:40 Name: Partners: Pre-Lab You are required to finish this section before coming to the lab it will be checked
HANDS-ON LAB INSTRUCTION SHEET MODULE 3 CAPACITORS, TIME CONSTANTS AND TRANSISTOR GAIN
HANDS-ON LAB INSTRUCTION SHEET MODULE 3 CAPACITORS, TIME CONSTANTS AND TRANSISTOR GAIN NOTES: 1) To conserve the life of the Multimeter s 9 volt battery, be sure to turn the meter off if not in use for
EECS40 Lab Introduction to Lab: Guide
Aschenbach, Konrad Muthuswamy, Bharathwaj EECS40 Lab Introduction to Lab: Guide Objective The student will use the following circuit elements and laboratory equipment to make basic circuit measurements:
Sept 13 Pre-lab due Sept 12; Lab memo due Sept 19 at the START of lab time, 1:10pm
Sept 13 Pre-lab due Sept 12; Lab memo due Sept 19 at the START of lab time, 1:10pm EGR 220: Engineering Circuit Theory Lab 1: Introduction to Laboratory Equipment Pre-lab Read through the entire lab handout
Electric Circuit Experiments
Electric Circuit Experiments 1. Using the resistor on the 5-resistor block, vary the potential difference across it in approximately equal increments for eight different values (i.e. use one to eight D-
Resistive Circuits. Lab 2: Resistive Circuits ELECTRICAL ENGINEERING 42/43/100 INTRODUCTION TO MICROELECTRONIC CIRCUITS
NAME: NAME: SID: SID: STATION NUMBER: LAB SECTION: Resistive Circuits Pre-Lab: /46 Lab: /54 Total: /100 Lab 2: Resistive Circuits ELECTRICAL ENGINEERING 42/43/100 INTRODUCTION TO MICROELECTRONIC CIRCUITS
Electric Circuit I Lab Manual. Session # 1
Electric Circuit I Lab Manual Session # 1 Lab Policies 1. Each lab session lasts 90 min and starts promptly. A brief introduction with demo may be given by the instructor at the beginning of the lab. Everybody
ENGINEERING COUNCIL CERTIFICATE LEVEL ENGINEERING SCIENCE C103
ENGINEERING COUNCIL CERTIFICATE LEVEL ENGINEERING SCIENCE C03 TUTORIAL 4 ELECTRICAL RESISTANCE On completion of this tutorial you should be able to do the following. Explain resistance and resistors. Explain
EE1020 Diodes and Resistors in Electrical Circuits Spring 2018
PURPOSE The purpose of this project is for you to become familiar with some of the language, parts, and tools used in electrical engineering. You will also be introduced to some simple rule and laws. MATERIALS
PHYS320(O) ilab Experiment 4 Instructions Diffraction and Interference: Measurement of the Wavelength of Light
Objective: PHYS320(O) ilab Experiment 4 Instructions Diffraction and Interference: Measurement of the Wavelength of Light The purpose of this activity is to determine the wavelength of the light emitted
EE EXPERIMENT 2 ANALOG AND DIGITAL MULTIMETERS INTRODUCTION. Figure 1: Internal resistance of a non-ideal ammeter.
Consider the two circuits shown in Figure 1 below. EE 2101 - EXPERIMENT 2 ANALOG AND DIGITAL MULTIMETERS INTRODUCTION Figure 1: Internal resistance of a non-ideal ammeter. The circuit on the left contains
The Art of Electrical Measurements
The Art of Electrical Measurements Purpose: Introduce fundamental electrical test and measurement tools and the art of making electrical measurements. Equipment Required Prelab 1 Digital Multimeter 1 -
Lab 3: Digital Multimeter and Voltage Generator
Lab 3: Digital Multimeter and Voltage Generator Lab Goals: Learn how to use your mydaq as a Digital Multimeter (DMM) Learn how to output a signal to a specified output port on the mydaq and verify its
Lab #1 Help Document. This lab will be completed in room 335 CTB. You will need to partner up for this lab in groups of two.
Lab #1 Help Document This help document will be structured as a walk-through of the lab. We will include instructions about how to write the report throughout this help document. This lab will be completed
Lab Equipment. PES 2160 Prelab Questions. Name: Lab Station: 005
** Disclaimer: This prelab is not to be copied, duplicated, and/or distributed, in whole or in part, unless approval is received from the University of Colorado at Colorado Springs Physics Department AND
Experiment no -1: Components Testing *
OpenStax-CNX module: m50547 1 Experiment no -1: Components Testing * Bijay_Kumar Sharma This work is produced by OpenStax-CNX and licensed under the Creative Commons Attribution License 4.0 Abstract This
EET 150 Introduction to EET Lab Activity 12 Temperature Sensor Amplifier Project
Required Parts, Software and Equipment Parts EET 150 Introduction to EET Lab Activity 12 Temperature Sensor Amplifier Project Figure 1 Flasher Circuit Component /alue Quantity LM741 OP AMP Integrated Circuit
Unit 3.C Electrical Theory, Circuits Essential Fundamentals of Electrical Theory, Circuits
Unit 3.C Electrical Theory, Circuits Essential Fundamentals of Electrical Theory, Circuits Early Booklet E.C.: + 1 Unit 3.C Hwk. Pts.: / 36 Unit 3.C Lab Pts.: / 50 Late, Incomplete, No Work, No Units Fees?
On-Line Students Analog Discovery 2: Arbitrary Waveform Generator (AWG). Two channel oscilloscope
EET 150 Introduction to EET Lab Activity 8 Function Generator Introduction Required Parts, Software and Equipment Parts Figure 1 Component /Value Quantity Resistor 10 kω, ¼ Watt, 5% Tolerance 1 Resistor
LAB 1: Familiarity with Laboratory Equipment (_/10)
LAB 1: Familiarity with Laboratory Equipment (_/10) PURPOSE o gain familiarity with basic laboratory equipment oscilloscope, oscillator, multimeter and electronic components. EQUIPMEN (i) Oscilloscope
Current, resistance, and Ohm s law
Current, resistance, and Ohm s law Apparatus DC voltage source set of alligator clips 2 pairs of red and black banana clips 3 round bulb 2 bulb sockets 2 battery holders or 1 two-battery holder 2 1.5V
LAB MODULES. MSCI 222C Introduction to Electronics. Charles Rubenstein, Ph. D. Professor of Engineering & Information Science
MSCI 222C Introduction to Electronics Charles Rubenstein, Ph. D. Professor of Engineering & Information Science LAB MODULES Copyright 2015-2019 C.P.Rubenstein Electronics Hands-On Lab - Module 01 MSCI
Lab 3: Kirchhoff's Laws and Basic Instrumentation
Lab 3: Kirchhoff's Laws and Basic Instrumentation By: Gary A. Ybarra Christopher E. Cramer Duke Universty Department of Electrical and Computer Engineering Durham, NC 1. Purpose The purpose of this exercise
ELECTRONICS An Introduction
BHAGAVATULA CHARITABLE TRUST ELECTRONICS An Introduction ఎల - ప చయ BCT-RHS BCT Farm Complex Haripuram Rambilli Mandal Visakhapatnam, AP 531061 Phone +91 (8924) 253 770 Fax +91 (8924) 253 780 Author: Sriram
LABORATORY Experiment 1
LABORATORY Experiment 1 Resistivity Measurement, Resistors and Ohm s Law 1. Objectives To measure the resistance of conductors, insulators and semiconductor and calculate the resistivity of a copper wire.
Practical 2P12 Semiconductor Devices
Practical 2P12 Semiconductor Devices What you should learn from this practical Science This practical illustrates some points from the lecture courses on Semiconductor Materials and Semiconductor Devices
AC/DC ELECTRONICS LABORATORY
Includes Teacher's Notes and Typical Experiment Results Instruction Manual and Experiment Guide for the PASCO scientific Model EM-8656 012-05892A 1/96 AC/DC ELECTRONICS LABORATORY 1995 PASCO scientific
Lab 11: Circuits. Figure 1: A hydroelectric dam system.
Description Lab 11: Circuits In this lab, you will study voltage, current, and resistance. You will learn the basics of designing circuits and you will explore how to find the total resistance of a circuit
Lab 2 Electrical Safety, Breadboards, Using a DMM
Lab 2 Electrical Safety, Breadboards, Using a DMM Objectives concepts 1. Safety hazards related to household electricity and electronics equipment 2. Differences between schematic and breadboard representations
Series and Parallel Resistors
Series and Parallel Resistors Today you will investigate how connecting resistors in series and in parallel affects the properties of a circuit. You will assemble several circuits and measure the voltage
Unit 1 Electronics Name: Form:
Unit 1 Electronics Name: Form: Electronics Electronics is the study of components and techniques used to be able to build circuits controlled by electricity. An electronic system uses discrete components.
University of Technology, Jamaica School of Engineering. Electrical Workshop Notes On Electrical components
University of Technology, Jamaica School of Engineering Electrical Workshop Notes On Electrical components Resistors Resistors are fundamental components in electronic circuits. A resistor is constructed
University of Jordan School of Engineering Electrical Engineering Department. EE 219 Electrical Circuits Lab
University of Jordan School of Engineering Electrical Engineering Department EE 219 Electrical Circuits Lab EXPERIMENT 4 TRANSIENT ANALYSIS Prepared by: Dr. Mohammed Hawa EXPERIMENT 4 TRANSIENT ANALYSIS
RESISTANCE & OHM S LAW (PART I
RESISTANCE & OHM S LAW (PART I and II) Objectives: To understand the relationship between potential and current in a resistor and to verify Ohm s Law. To understand the relationship between potential and
Electric Circuit I Lab Manual Session # 2
Electric Circuit I Lab Manual Session # 2 Name: ----------- Group: -------------- 1 Breadboard and Wiring Objective: The objective of this experiment is to be familiar with breadboard and connection made
PHYS 1112L - Introductory Physics Laboratory II
PHYS 1112L - Introductory Physics Laboratory II Laboratory Advanced Sheet dc Circuits 1. Objectives. The objectives of this laboratory are a. to be able to construct dc circuits given a circuit diagram
Circuit Analysis Laboratory Workbook
Circuit Analysis Laboratory Workbook Synthesis Lectures on Electrical Engineering Editor Richard C. Dorf, University of California, Davis Circuit Analysis Laboratory Workbook Teri L. Piatt and Kyle E.