Assembly and operating instructions for operation with the local interface

Transcription

1 CentralControl CC51, CC31 en Assembly and operating instructions for operation with the local interface Central controller Important information for: Fitters / Electricians / Users Please forward accordingly! These instructions must be kept safe for future reference /07/2017 Becker-Antriebe GmbH Friedrich-Ebert-Straße Sinn/Germany

2 Table of contents General... 5 Warranty... 5 Items included... 6 Safety instructions... 6 Intended use... 8 Dimensions... 9 Device overview Start / standard screen Mains connection Explanation of pictograms Explanation of the operator controls Operating the house automation with other devices on the home network Operating the house automation through a device with mobile Internet access from outside Preparing to commission the CC Commissioning with the local interface Setting the language Establishing a network connection Setting the time and date Setting the location Adding a Centronic receiver Adding a B-Tronic receiver Adding a room Adding elements to a room End of commissioning Building wiring system settings Adding a Centronic receiver Adding a B-Tronic receiver Deleting a Centronic receiver Deleting a B-Tronic receiver Renaming a receiver Adding a Centronic or B-Tronic transmitter Deleting a Centronic or B-Tronic transmitter Renaming a transmitter Adding a Centronic or B-Tronic sensor Deleting a Centronic or B-Tronic sensor Renaming a sensor Adding an internal object Deleting an internal object Renaming an internal object Linking a transmitter to a function (adding logic) Linking a sensor to a function (adding logic) Linking an internal object to a function (adding logic)

3 My Home settings Adding a room Sorting rooms Deleting a room Renaming a room Allocating elements to a room Sorting elements in a room Deleting elements from a room Adding a group Sorting groups Deleting a group Renaming a group Allocating elements to a group Deleting elements from a group Adding a scenario Sorting scenarios Deleting a scenario Renaming a scenario Allocating elements to a scenario Deleting elements from a scenario Adding a camera Sorting cameras Deleting a camera Changing camera settings Adding a radio Sorting radios Deleting a radio Changing radio settings Automation settings Setting the memory function (ON/OFF) Setting the automatic roof window Setting the holiday function Setting the sun protection function Adding a timer Changing a timer Deleting a timer Setting the heating functions Access settings Generating a service code Setting up remote access for an existing account Setting up remote access for a new account View settings Setting the background colour Setting the visual background effects

4 Resetting the background colour and the visual background effects to the factory settings Information settings System information Reading out the error memory Reading update news System settings Setting the language Setting the location Setting the time and date Establishing a network connection Update Creating a backup Restoring from backup Factory reset Reboot Rooms Setting receivers to Automatic mode Setting all the receivers in the room to Automatic mode Setting all the receivers in the home to Automatic mode Setting receivers to Manual mode Setting all the receivers in the room to Manual mode Setting all the receivers in the home to Manual mode Operating receivers Adding favourites Deleting favourites Groups Operating groups Scenarios Operating scenarios Cameras Calling up cameras Radios Starting a radio Stopping a radio Weather forecast Changing the batteries of an external keyboard Cleaning Technical data Technical data for the CC Technical data for the CC What to do if...? Simplified EU declaration of conformity Annex Astronomical function

5 General With the B-Tronic CentralControl you can operate the drives and control units with bidirectional KNX radio and the Centronic I and II range of controls. This device uses free/open source software. The source code can be downloaded from On request, Becker Antriebe will make the source code available on a CD-ROM at cost price. Please contact source@b-tronic.net if you are interested. As a result of continuous further development of the software, there can be differences between the illustrations and your device. This is not, however, important for any of the procedures described. Please observe these Assembly and Operating Instructions when installing and setting up the equipment. Warranty Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in serious injuries, e.g., crushing of limbs. Therefore, structural modifications may only be carried out with our prior approval and strictly in accordance with our instructions, particularly the information contained in these Assembly and Operating Instructions. Any further processing of the products which does not comply with their intended use is not permitted. The end product manufacturer and fitter have to ensure that all the relevant current statutory, official and, in particular, EMC regulations are adhered to during utilisation of our products, especially with regard to end product manufacture, installation and customer advice. 5

6 Items included CC51 B-Tronic CentralControl control unit USB WLAN stick USB Flash memory stick USB Centronic stick USB B-Tronic/KNX stick Mains adapter Fasteners for wall mounting Commissioning instructions CC31 B-Tronic CentralControl control unit Flash memory SD card USB Centronic stick USB B-Tronic/KNX stick Mains adapter Wireless keypad (incl. USB receiver stick and batteries) Commissioning instructions Safety instructions General information Please keep the instructions safe! Only use in dry rooms. Keep people out of the system s range of travel. Keep children away from control units. Observe all pertinent country-specific regulations. Do not place any objects on the control unit. Clean the control unit with a soft, dry, lint-free cloth, and do not use any chemical cleaning agents. Caution If the system is controlled by one or more transmitters, the system s range of travel must always be visible during operation. Keep packaging materials such as film away from children. Misuse can create the risk of suffocation. 6

7 Switch the control unit off immediately if the mains adapter and the plug to which it is connected is burnt or damaged. If a mains adapter is damaged, replace it with an original one. A faulty mains adapter must not under any circumstances be repaired. Switch the control unit off immediately if the housing of the control unit is damaged, or if liquids have penetrated. Attention Do not let any objects fall onto the control unit. If a display is present, protect it against being scratched by hard objects (e.g. rings, fingernails, wristwatches) Wait until the control unit has adjusted to ambient temperature before connecting the control unit to the mains adapter. Condensation that could lead to a short circuit can be caused inside the control unit by large differences in temperature and air humidity. 7

8 Intended use The B-Tronic CentralControl may only be used for the operation of suitable drives and control units with bidirectional KNX radio and with the Centronic I and II range of controls. You can operate a group, or multiple groups, of devices with this controller. Please note that radio-controlled systems may not be used in areas with a high risk of interference (e.g. hospitals, airports). The remote control is intended solely for use with equipment and systems in which malfunctions in the transmitter or receiver would not pose any risk to persons, animals or property, or which contain safety devices to eliminate such risks. The operator is not protected from interference from other telecommunications systems and terminal equipment (e.g. even from radiocontrolled systems which are properly operated in the same frequency range). Only connect radio receivers to devices and systems approved by the manufacturer. Ensure that the control unit is not installed or operated close to metal surfaces or magnetic fields. Radio-controlled systems transmitting on the same frequency may cause reception interference. Note that the range of the radio signal is limited by legislation as well as by design. 8

9 Dimensions All dimensions in mm. CC51 CC31 28,

10 Device overview CentralControl CC Integrated front camera 2. Light sensor 3. Loudspeaker 4. Touchscreen 5. Operating status LED 6. Microphone 7. USB backup memory 8. Free USB connector 9. Centronic stick 10. B-Tronic KNX stick 11. Connection for mains adapter 12. Audio output (3.5 mm jack) 13. WLAN stick 14. Network connection (RJ45) 15. Reset button 16. Cover 17. Feet 10

11 CentralControl CC31 Connections/slots Mains connection 2. LAN connection 3. HDMI connection 4. AV connection 5. YUV connection 6. Free USB 2.0 connection 7. USB connection for B-Tronic KNX stick 8. USB connection for Centronic stick 9. USB connection for keypad stick 10. Card slot for SD card 11. Operating status LED Rear of the device 1 2 B-Tronic CentralControl CC SSID: CC31-XXXX : WPACC31-YYY IP: IP MAC-ETH: b4:4a:bc:03:09:aa Serial: WLAN wireless network (SSID) 2. WLAN network key (KEY) 11

12 External keypad Touchpad 2. ON/OFF switch 3. Keypad 4. No function 5. Light button 6. LED light 7. Battery compartment 8. Compartment for keypad receiver 9. Battery compartment cover 12

13 Start / standard screen Main screen area The time and date, and in some cases the weather forecast, are displayed on the main screen area. 2 Navigation and status area The current weather, status information, and the navigation elements for the programmed receivers are shown in the navigation and status area. 3 Time / date Display of date and time. The time can be displayed in digital or analogue format. 4 Weather Display of the current weather at the selected weather location. Displaying the weather data requires an Internet connection. 5 Device status bar The statuses of various device-specific functions are displayed on this status bar: B-Tronic KNX stick is available in the device. B-Tronic KNX stick is not available in the device. Centronic RF stick is available in the device. Centronic RF stick is not available in the device. WLAN signal strength No WLAN available 13

14 Network via cable No network via cable Access point available Fault indication 6 Main navigation An update is available The display of blue triangles indicates that more content is available in the main screen area by scrolling up or down. The main navigation is visible, with an identical format, on all the screens. It consists of the following three navigation panes: Clicking this button will always take you back to the start screen. Clicking this button takes you to the operating facilities for the receivers, rooms, groups and scenarios. Clicking this button will take you to the settings. Mains connection 1. If necessary, pull the cover off the control unit. 2. First connect the mains adapter to the control unit, then plug it into the socket. 3. If you removed the cover, place it back onto the control unit now. Explanation of pictograms CAUTION ATTENTION CAUTION indicates a hazardous situation which, if not avoided, could result in injury. ATTENTION indicates measures that must be taken to avoid damage to property. Denotes user tips and other useful information. 14

15 All the symbols in square boxes can be found on the screen and should be operated there using the mouse or touchscreen. All the symbols in circles provide operating information that should be implemented if a symbol is illustrated in a circle. Continue with the entries at the point indicated. Select one or more options from a preset list.* Fill in one or more text boxes.* Fill in the text boxes and select the desired options.*! Please note the information on the screen.* The task is complete. Perform the next step (with and without identification) Continue, depending on the result of the previous action Action not completed successfully or Action completed successfully *) It may be necessary to scroll down the page to reach all the information, options, input fields, etc. 15

16 Explanation of the operator controls The operator controls may execute different functions depending on the receiver type. Move UP/move IN Switch on the light and increase the brightness Manually set the temperature higher STOP button Switch off the light Move DOWN, move OUT Switch on the light and reduce the brightness Manually set the temperature lower ON button OFF button ON button Switch on the anti-freeze mechanism/battery energy-saving mode 1 Intermediate position 1 (optional) Saved light value 1 (optional) 2 Intermediate position 2 (optional) Saved light value 2 (optional) Intermediate position with optional closing Comfort temperature Eco temperature 16

17 Fold out the foldable roller shutter Fold up the foldable roller shutter Operating the house automation with other devices on the home network You can use the B-Tronic CentralControl to remotely control home automation functions using a large number of end devices that are in your home network. The devices can be integrated into the network by means of a network cable a or WLAN b. The operating system on which your end device is based is of no importance. Microsoft Windows (from XP/Internet Explorer 8), Android and Apple ios (Mac, ipad, iphone) are amongst the supported systems. a b To communicate with the central controller over the network, please start your Internet browser and enter the IP number into your browser s address field. The entry always starts with followed by the IP number. This is always represented by four numbers with at most three digits each, separated by dots. The entry in the example is: You can call up the IP number assigned for your central controller by the network on the System information page: To access your CentralControl quickly at any time, you can save the page you called up using the IP address as a favourite or store it on your device s desktop. To ensure that a different IP address is not used each time the CentralControl is rebooted, it should be assigned a fixed IP address (see Establishing a network connection). 17

18 Operating the house automation through a device with mobile Internet access from outside You need to register with the Becker Gateway Service for easy remote control of your central controller over the Internet. A login code is required once in order to set up gateway access at You will find out how to receive a login code in the chapter entitled Setting up remote access for a new account or Setting up remote access for an existing account. Please note that an Internet connection and an account are necessary in order to request a login code. After you have successfully logged into the Becker Gateway Service, it is no longer possible to generate another login code with the same central controller. You can, of course, assign a number of central controllers to one user account. Preparing to commission the CC31 Insert the supplied stick into the B-Tronic CentralControl in accordance with the Device overview. There are a number of display options: Via television or screen Via PC, notebook or tablet Via television or screen 1. Connect the B-Tronic CentralControl to the television or screen using the HDMI cable or the AV cable. 2. First connect the mains adapter to the control unit, then plug it into the socket. Caution Lay the mains connecting cable in such a way that nobody can tread on it or trip over it. 18

19 3. The Start / standard screen [} 13] appears. 4. You can now input further entries via the internal keypad, or via the external keypad supplied. Via PC, notebook or tablet There are a number of options: WLAN Ethernet (an Ethernet cable is not included in the scope of supply) WLAN The configuration WLAN of the B-Tronic CentralControl (access point) is used to make the first connection with your input device. 1. Make a note of the name of the WLAN wireless network (SSID) and of the WLAN network key (KEY). Both can be found on the back of the B-Tronic CentralControl. 2. Have the wireless networks shown to you by your input device (PC, notebook or tablet). 3. Select the WLAN wireless network (SSID) that you noted previously from the list of available connections and start the connection request. 4. Now enter the WLAN network key (KEY) that you noted previously into the field provided and connect to the B-Tronic CentralControl. Wait until the WLAN connection is established. 5. Then open your browser via the input device. 6. Now type the following address into the browser s address bar: and confirm it by pressing Enter. 7. The start/standard screen appears. 8. Select 9. Now make the settings for your private network. 10. Then set your input device back to the private network. If you cannot find your CC31 in your network, you must reset the CC31 to Hot Spot mode. To do so, press the following key combination on the external keypad supplied: ESC + Shift + Ctrl. Then repeat the above process. 19

20 Ethernet (an Ethernet cable is not included in the scope of supply) 1. Connect the B-Tronic CentralControl to your input device (PC, notebook or tablet) using the Ethernet cable. Wait until the Ethernet connection is established. Caution Lay the Ethernet cable in such a way that nobody can tread on it or trip over it. 2. Then open your browser via the input device. 3. Now type the following address into the browser s address bar: and confirm it by pressing Enter. 4. The Start / standard screen [} 13] appears. 5. Select 6. You can now input further entries via your input device. Commissioning with the local interface The following pages will guide you step-by-step through the installation and configuration of the B-Tronic CentralControl. When all the steps described have been carried out, your rooms and receivers will be configured and you will be able to centrally control your home. However, the B-Tronic CentralControl has significantly more convenience and automation options available that you can use to adapt your home automation to suit your individual needs. These functions are described in detail under the menu items from the chapter entitled Building wiring system settings [} 24]. Setting the language Language 20

21 Establishing a network connection The full home automation functionality of the B-Tronic CentralControl is naturally available even when it is not connected to a network. However, some additional functions and access options are only possible with network or Internet access. To be able to use these functions, please ensure that the B-Tronic CentralControl is connected to your network, that there is an Internet connection and that the time is set correctly. The central controller can only be integrated in a network by means of WiFi/ WLAN if the WPA2 encryption is switched on at the router. Please note that this may result in charges depending on your Internet provider s contractual conditions. Network settings To ensure that a different IP address is not used every time the CentralControl reboots, a fixed IP address should be assigned to the CentralControl. The network configuration must be switched from Automatic to Manual in this case. Ask your network administrator for the additional information required for this purpose. Setting the time and date Date/time 21

22 Setting the location This setting affects the weather information used, the time zone and the Astro function. Location Adding a Centronic receiver! 22

23 Adding a B-Tronic receiver!!! Adding a room Adding elements to a room End of commissioning 23

24 Adding a Centronic receiver Building wiring system settings! Adding a B-Tronic receiver!!! 24

25 Deleting a Centronic receiver!! Deleting a B-Tronic receiver!! 25

26 Renaming a receiver The following functions are unavailable on the local interface. Please make this setting on the web interface. Adding a Centronic or B-Tronic transmitter Deleting a Centronic or B-Tronic transmitter Renaming a transmitter Adding a Centronic or B-Tronic sensor Deleting a Centronic or B-Tronic sensor Renaming a sensor Adding an internal object Deleting an internal object Renaming an internal object Linking a transmitter to a function (adding logic) Linking a sensor to a function (adding logic) Linking an internal object to a function (adding logic) 26

27 My Home settings Adding a room Sorting rooms Deleting a room Renaming a room 27

28 Allocating elements to a room Sorting elements in a room Deleting elements from a room Adding a group A group is a number of receivers combined on one of the transmitter s channels. All the receivers in a group respond jointly to signals from the transmitter. It is important to note that only receivers of the same type e.g. roller shutter drives or switching receivers can be combined in one group. 28

29 The list of receivers also contains groups and scenarios, and these can also be assigned to rooms in the exact same way as individual receivers. Sorting groups Deleting a group Renaming a group Allocating elements to a group 29

30 Deleting elements from a group Adding a scenario Several receivers are combined in one scenario. All the receivers in a scenario respond jointly to the commands for starting or stopping the scenario. In contrast to the group, devices combined in one scenario do not have to consist of receivers of the same type. They can approach positions that have been individually defined beforehand, or can assume switching states. Confirmation (positive/negative) is only provided once the last scenario participant has issued a status message. To ensure correct execution of scenarios that involve several receivers of the same type, (i.e. several roller shutter drives), please create a shared group for them. This group can then be applied in the scenario. This measure ensures that the receivers all receive the travel/switching commands at the same time. The list of receivers also contains groups and scenarios, and these can also be assigned to rooms in the exact same way as individual receivers. 30

31 Sorting scenarios Deleting a scenario Renaming a scenario Allocating elements to a scenario 31

32 Deleting elements from a scenario Adding a camera It is possible to integrate up to 25 network-enabled cameras that make an MJPEG stream available. You can find out whether your camera model makes such a stream available from your camera s manufacturer. Please note that the central controller can only display native MJPEG/MJPG streams. You can find a list of the cameras that Becker has already tested and incorporated at You will also find a list of the cameraspecific settings there. Sorting cameras Deleting a camera 32

33 Changing camera settings Adding a radio Sorting radios Deleting a radio 33

34 Changing radio settings Automation settings Setting the memory function (ON/OFF) The CentralControl enables configuration of a number of timer functions. Particularly in installations where the central controller is installed at a later time, memory functions that have been set in the drives may already exist. To completely set all the times through the central controller, the memory times stored in the drives can be switched off using the Internal memory function option. Please note that the memory function in any given drive is only finally deactivated when the central controller has once switched it to manual mode (the drive confirms this by clicking). Switching off in this way occurs at every change to manual mode. The drives memory function can be reactivated at any time using a memory hand-held transmitter. Automation options Receiver memory function 34

35 Setting the automatic roof window Automation options Automatic roof window Setting the holiday function Your CentralControl includes a holiday function, so that even when you are not there, any possible observer would be given the impression that the drives are not controlled automatically, but manually. If this function is activated, programmed switching times are shifted every day by a time determined by a random generator. You can define this time shift in the Holiday function menu. The time that you save is the maximum time by which the switching time will be moved forwards or backwards. Automation options Holiday function 35

36 Setting the sun protection function Adding a timer To ensure that time commands are executed correctly, you need to create a shared group for receivers of the same type. This group can then be applied to the timers. This measure ensures that the receivers all receive the travel/switching commands at the same time. All the receivers must be in Automatic mode. You will find a more detailed explanation of the Astro function under Astronomical function [} 53]. Changing a timer To ensure that time commands are executed correctly, you need to create a shared group for receivers of the same type. This group can then be applied to the timers. This measure ensures that the receivers all receive the travel/switching commands at the same time. All the receivers must be in Automatic mode. 36

37 You will find a more detailed explanation of the Astro function under Astronomical function [} 53]. Deleting a timer Setting the heating functions Please note that all the heating actuators in a room automatically form a joint climate zone and are controlled together. Individual control is only possible via the + and buttons on the heating actuator. 37

38 Generating a service code Access settings Service Generate service code! 38

39 Setting up remote access for an existing account Remote access Please take note of the code and complete the registration process in the web browser using a computer, tablet or mobile phone. Then enter the following address in the web browser: Log in Activate device No 39

40 Setting up remote access for a new account Remote access Please take note of the code and complete the registration process in the web browser using a computer, tablet or mobile phone. Then enter the following address in the web browser: Create new account. Create account. Confirm the account. Then enter the following address in the web browser: Log in. 40

41 Setting the background colour View settings This function is unavailable on the local interface. Please make this setting on the web interface. Setting the visual background effects This function is unavailable on the local interface. Please make this setting on the web interface. Resetting the background colour and the visual background effects to the factory settings This function is unavailable on the local interface. Please make this setting on the web interface. Information settings System information! Reading out the error memory! 41

42 Reading update news News! System settings Setting the language Language Setting the location This setting affects the weather information used, the time zone and the Astro function. Location 42

43 Setting the time and date Date/time Establishing a network connection The full home automation functionality of the B-Tronic CentralControl is naturally available even when it is not connected to a network. However, some additional functions and access options are only possible with network or Internet access. To be able to use these functions, please ensure that the B-Tronic CentralControl is connected to your network, that there is an Internet connection and that the time is set correctly. The central controller can only be integrated in a network by means of WiFi/ WLAN if the WPA2 encryption is switched on at the router. Please note that this may result in charges depending on your Internet provider s contractual conditions. Network settings To ensure that a different IP address is not used every time the CentralControl reboots, a fixed IP address should be assigned to the CentralControl. The network configuration must be switched from Automatic to Manual in this case. Ask your network administrator for the additional information required for this purpose. 43

44 Update Update! Download and install now! Even if you decide not to connect your central controller to the Internet, you are still able to download current software updates and, in that way, install additional functionalities or bug fixes at a later time. To do so, please download the CC Updater onto your PC by using the following link: Then start the CC Updater and follow the instructions on the screen. Creating a backup Backup + Restore Carry out backup now 44

45 Restoring from backup Backup + Restore Restore settings Factory reset All settings will be reset, and all rooms, scenarios, groups, receivers and so forth will be deleted. Factory settings Reboot Reboot 45

46 Rooms Setting receivers to Automatic mode The B-Tronic CentralControl enables you to control receivers, groups or scenarios according to time. All the control tasks carried out by the CentralControl based on programmed specifications (such as switching times) are referred to as Automatic functions. Automatic functions can be activated or deactivated for either one single receiver or for several receivers (the entire home or one room) at the same time. Receivers for which no automatic options have been defined remain unaffected by this change. Setting all the receivers in the room to Automatic mode Setting all the receivers in the home to Automatic mode Setting receivers to Manual mode Setting all the receivers in the room to Manual mode 46

47 Setting all the receivers in the home to Manual mode Operating receivers Adding favourites Favourites Deleting favourites Favourites 47

48 Groups Operating groups Scenarios Operating scenarios Cameras Calling up cameras Radios Starting a radio 48

49 Stopping a radio Weather forecast Changing the batteries of an external keyboard Dispose of exhausted batteries properly. Only replace batteries with ones of the identical type (LR03; AAA). 1. Open the cover of the battery compartment. 2. Take out the batteries. 3. Insert the new batteries correctly. 4. Close the cover of the battery compartment. Cleaning Only clean the device with a suitable cloth. Do not use aggressive cleaning agents that may damage the surface. 49

50 Technical data for the CC51 Technical data Supply voltage 230 V/50 Hz Degree of protection IP 20 Permissible ambient temperature and air humidity Maximum emitted transmission output Radio frequency CPU Memory Display Camera Operating system Dimensions (W x H x D) 0 C to +55 C at a relative humidity of between 20% and 80% (noncondensing) 25 mw MHz ARM9 454 MHz 128 MB 10.9 cm/4.3 inch touchscreen Resolution: 480 x 272 pixels 640 x 480 pixels, VGA RGB Linux 197 x 156 x 34 mm Connections USB WLAN stick Flash memory USB Centronic RF stick USB B-Tronic KNX stick Ethernet Audio output IEEE802.11n WPA/WPA2 USB stick MHz MHz 10/100 Mbit, standard RJ mm jack The maximum transmitter range on and in the building is up to 25 m, and up to 350 m in the open. 50

51 Technical data for the CC31 Supply voltage 230 V/50 Hz Degree of protection IP 20 Permissible ambient temperature and air humidity Maximum emitted transmission output Radio frequency CPU Memory Operating system Dimensions (W x H x D) 0 C to +40 C at a relative humidity of between 20% and 80% (noncondensing) 25 mw MHz/2.4 GHz ARM9 454 MHz 128 MB Linux 118 x 118 x 28.5 mm Connections Integrated WLAN Flash memory USB Centronic RF stick USB KNX stick Ethernet IEEE802.11n WPA/WPA2 SD card MHz MHz 10/100 Mbit, standard RJ45 HDMI Audio output 3.5 mm jack The maximum transmitter range on and in the building is up to 25 m, and up to 350 m in the open. 51

52 What to do if...? Problem B-Tronic CentralControl is not working/ does not start. Weather is not displayed. Radio does not work. Remedy Check the mains connection (see Device overview). Connect the B-Tronic CentralControl to the network and Internet (see Establishing a network connection [} 43]). Connect the B-Tronic CentralControl to the network and Internet (see Establishing a network connection [} 43]). Increase the volume. (see Starting a radio [} 48]). Internet speed is insufficient. Time and date are not set automatically. Change the automatic time check from Manual to Automatic (see Setting the time and date [} 43]). Connect the B-Tronic CentralControl to the network and Internet (see Establishing a network connection [} 43]). Programming a receiver does not work. Reduce distance from receiver. Deactivate all repeaters. Reprogram the receiver according to the receiver s instructions. Select the correct receiver type (KNX/ CENTRONIC) (see Adding a Centronic receiver [} 24] or Adding a B-Tronic receiver [} 24]). Select the correct device type (tubular drive/switching actuator/dimming actuator, etc.) (see Adding a Centronic receiver [} 24] or Adding a B-Tronic receiver [} 24]). Make free storage space available according to the receiver s instructions. 52

53 Problem Switching/movement of a receiver does not work. Remedy Check the receiver s mains connection. Reprogram the receiver. Reduce the distance from the receiver, or use a repeater. Reduce the number of repeaters if using several of them. You will find further information at Simplified EU declaration of conformity Becker-Antriebe GmbH hereby declares that this radio control system complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following web address: Subject to technical changes without notice. Astronomical function Annex To execute Astro functions the location of the CentralControl must be entered correctly. This can be specified in the Select location menu. The B-Tronic CentralControl controls your home automation systems as required via the Astro function, according to the calculated sunrise and sunset times. You can assign one of the two Astro versions to each timer: - Astro dawn - depending on sunrise - Astro evening - depending on sunset For each of these two variants there are two more possible settings, described in more detail below. Diagram notes: - Each of the yellow lines represents the time of sunrise or sunset. - Each of the blue lines represents the time at which the desired action is to be performed by the timer. 53

54 ASTRO DAWN Astro dawn without any additional settings: The desired action is performed at the time of sunrise. Winter time Summer time Winter time Jan. Feb. Mar. Apr. May June July Aug. Sep. Oct. Nov. Dec. Astro dawn with blocking time: The desired action is carried out at the time of sunrise, but not before the set blocking time (which is 6:00 AM in the example). Astro dawn with shift: The desired action is not carried out at dawn itself, but is shifted by whatever "Astro shift" has been set. In the example, 1 hour has been set as the Astro shift. The action is not, for example, carried out at 7:00 AM (sunrise), but an hour later at 8:00 AM. Winter time Summer time Winter time Jan. Feb. Mar. Apr. May June July Aug. Sep. Oct. Nov. Dec. Blocking time Winter time Summer time Winter time Jan. Feb. Mar. Apr. May June July Aug. Sep. Oct. Nov. Dec. ASTRO EVENING Astro evening without any additional settings: The desired action is performed at the time of sunset. Winter time Summer time Winter time Jan. Feb. Mar. Apr. May June July Aug. Sep. Oct. Nov. Dec. Astro evening with blocking time: The desired action is carried out at the time of sunset, but not after the set blocking time (which is 6:00 PM in the example). Winter time Summer time Winter time Jan. Feb. Mar. Apr. May June July Aug. Sep. Oct. Nov. Dec. Blocking time 54

55 Astro evening with shift: The desired action is not carried out at evening itself, but is shifted by whatever "Astro shift" has been set. In the example, 1 hour has been set as the Astro shift. The action is not, for example, carried out at 7:00 PM (sunset), but an hour earlier at 6:00 PM. Winter time Summer time Winter time Jan. Feb. Mar. Apr. May June July Aug. Sep. Oct. Nov. Dec. 55

56