ENGLISH. Stock N o Stability indicator Light on/ Dark. on optional Output can be

Transcription

1 Product Datasheet Optical Fiber Amplifier Stock N o Feature Description Sensing distance can be set by key (Self learning) Stability indicator Light on/ Dark on optional Output can be set, NO delay or OFFF delay 100ms Reverse polarity protection, shock protection, overload protection and short-circuit protection

2 Features Limiting voltage Fluctuation voltage Current consumption Leak current Outpu delay Outpu mode Power Supply Protection Outpu protection Voltage drop Indicator display Rated load current Min load current Hysteresis Repeated accuracy Efficient operation distance Distance regulation Response time Temperature drift Ambient temperature Light source EMC-ESD EMC-Burst EMC-HF Dielectric property Anti-vibration Anti-shock Protection degree Connection Housing material DC10 30V <10% <40mA <0.1mA There are two ways for setting: Norm; Off delay 100ms NPN+PNP;L.ON/D.ON Dial switch optional Polarity protection, shock protection Overload protection, short-circuit protection ) Output indicator, power indicator, stability indicator, setting indicator Short - circuit /overload indicator, 100mA 1mA 3%...20% <5% 1~80mm (90% reflective rate, 100*100mm white card, with fiber cable PRC-610 for test) Key <1ms <10% 0 ~50 Visible red light ±4kVV CD/±8kV AD (IEC ) ±2kVV 5kHz (IEC ) 3V/m (IEC )/ 3V (IEC ) <0.2mA (500VAC,60s) Amplitude:1mm;Frequency:10~55Hz;Sweep frequency cycle: 5min Shock (Impulse) wave shape: Half sine; Peak speed: 30gn; Pulse duration: 11ms IP54 2M PVC cable PC+ +ABS

3 Operating instructions Control panel symbol Definitionn of key and dial switch Function of SET key: Sensing distance setting 1. Put target object in the distance setting position; 2. Press SET key for 2~5 seconds, then release, red and green LED will flicker mutually with 2Hz frequency, then it will enter setting mode; 3. If the sensor enters working mode after red and green LED flickering 3 times at the same time with 2Hz frequency, it means that the setting is successful; 4. If red and green LED flicker mutually with 8Hz frequency, it means that the receiving signal is not strong and the setting failed. Based on this condition, please take corresponding actions according to below failure reasons, and repeat 1.2.steps once failures removed; Failure reason The size of sensing face is too small The distance is too far The reflective rate of target object is too low Measures Increase the size of sensing face Reduce the distance between the target object and optical fiber head Increase the reflective rate of target object NORM/OFF DLY 100ms Function definition NORM: Output is without delay OFF DLY 100ms:Off delay 100ms L.ON/D.ONN Definitionn L.ON: The output is on wheree there is light signal D.ON: The output is on wheree there is no light signal

4 LED indicator Red LED(OUT): Outpu indicator, short-circuit indicator; Output indicator: Red LED and output relations are as shown in below figure; Short-circuit indicator: When output is on and short-circuit appears, red LED will flicker with 4Hz frequency; Green LED (POWER): Power indicator, signal stability indicator; Signal stability indicator: When there is stable light signal or no light signal, the indicator is on; When light signal is unstable, green LED will flicker with 2Hz frequency; Power indicator: Green LED is always on or flickers with 2Hz frequency, which means that the power is stable. Attentions When red LED flickers rapidly, it means that the load current is exceeded or there appears short -circuit, so please check the load and reduce the load current. Installation instructionss Optical fiber installation Unscrew the fixed cover (As shown below), insert the fiber cable into corresponding fixed hole, and reversely screw the fixed cover.

5 * To ensure normal use of the product, please embed the fiber cable into the bottom of fixed Connection diagram Use of cutter Optical fiber cutter can cut the fiber to be actual required length. 1. Put fiber into corresponding hole of cutter and reserve the required length in advance. 2. Press the cutter blade with high speed, which can cut the fiber successfully. * To ensure the fiber performance, every cutter hole can be used only once. * To ensure the fiber performance, try to cut the fiber successfully at a time, please avoid cutting the same point for many times. Installation and removal of amplifier Installation of amplifier 1. Press the A-end of the amplifier into DIN guide rail or mounting rack; 2. Press the B-end of amplifier into DIN guide rail or mounting rack. The sequence of A and B can't be reversed during installation, if installed the backward, the installation strength will be reduced.

6 Removal of amplifier Press the amplifier. Installed side by side amplifier to direction C, and uplift the imbedded fiber to direction D, which can remove the 1. Install the amplifier on DIN rail, one amplifier one time. 2. Push the permanent seat to the end, so that the amplifier can be fixed. (Permanent seat is included in the expansion module, pleasee be sure to use it.) Electrical wiring diagram

7 Dimension (mm)