SFP-WB Gigabit Ethernet-Single Mode Transceiver

Transcription

1 SFP BIDI, Single LC Connector, 1550nm DFB LD for Single Mode Fiber, ohs Compliant Features ohs Pb Applications Gigabit Ethernet Links Fiber Channel Links at 1.06 Gbps High Speed Backplane Interconnects Switched Backbones Description 1550nm DFB LD Multi Data ate: from 125M to 1.25Gbps, NZ Single +3.3V Power Supply ohs Compliant and Lead-free AC/AC Differential Electrical Interface Compliant with Multi-Source Agreement (MSA) Small Form Factor Pluggable (SFP) Single LC Connector Compliance with specifications for IEEE-802.3z Gigabit Ethernet at 1.25 Gbps Compliance with ANSI specifications for Fiber Channel applications at 1.06 Gbps Eye Safety Designed to meet Laser Class 1, complies with EN he SFP-WB10 from AAXEON is the high performance and cost-effective module for serial optical data communication applications specified for single mode of multi-rate from 125M to 1.25 Gb/s. It operates on +3.3V power. he module is intended for single mode fiber, operates at a nominal wavelength of x: 1550nm / x: 1310nm, and complies with Multi-Source Agreement (MSA) Small Form Factor Pluggable (SFP). Each module consists of a bi-directional optical subassembly that combines a transmitter with a receiver and an electrical subassembly. All are housed in a metal package and the combination produces a reliable component. he module is a single fiber connector transceiver designed for use in Gigabit Ethernet applications and to provide IEEE-802.3z compliant link for 1.25Gb/s intermediate reach applications. he characteristics are performed in accordance with elcordia Specification G-468-COE. EMC Most equipment utilizing high-speed transceivers will be required to meet the following requirements: 1) FCC in the United States 2) CENELEC EN55022 (CISP 22) in Europe o assist the customer in managing the overall equipment EMC performance, the transceivers have been designed to satisfy FCC class B limits and provide good immunity to radio-frequency electromagnetic fields. Eye Safety he transceivers have been designed to meet Class 1 eye safety and comply with EN Page 1 of 6

2 Product Information Operating Voltage Model Number Distance Wavelength Output Power Sensitivity & SD Output SFP-WB10 3.3V L AC/AC 10 km 1550 nm DFB / 1310 nm -9 ~ -3 dbm -21 dbm ABSOLUE MAX AINGS PAAMEE SYMBOL MIN MAX UNI NOE Storage emperature S C Supply Voltage V CC 0 6 V Data Input Voltage Vcc V Supply Current I S 300 ma OPEAING CONDIIONS PAAMEE SYMBOL MIN. YP. MAX. UNI NOE Case Operating emperature A 0 70 C Supply Voltage V CC V Data Input Voltage Swing V ID mv ELECICAL CHAACEISICS PAAMEE SYMBOL MIN MAX UNI NOE ransmitter ransmitter Supply Current I CC 200 ma x_ Disable Input Voltage - Low V IL V x_ Disable Input Voltage - High V IH 2.0 Vcc V x_ Fault Output Voltage - Low V OL V x_ Fault Output Voltage - High V OH 2.0 Vcc V eceiver eceiver Supply Current I CC 100 ma eceiver Data Output Differential Voltage V OD V x_los Output Voltage - Low V OL V x_los Output Voltage - High V OH 2.0 Vcc V MOD_DEF (1), MOD_DEF (2) - Low V IL -0.6 Vcc 0.3 V MOD_DEF (1), MOD_DEF (2) - High V IH Vcc 0.7 Vcc V ANSMIE ELECO-OPICAL CHAACEISICS PAAMEE SYMBOL MIN YP. MAX UNI NOE Optical Output Power Po -9-3 dbm 1 Extinction atio E 9 db Center Wavelength λ c nm Spectral Width (-20dB) Δλ 1 nm Side Mode Suppression atio SMS 30 db IN IN -120 db/hz Optical ise time (20%-80% ) t r 260 ps 2 Optical Fall time (20%-80% ) t f 260 ps 2 Output Eye Compliant with IEEE802.3z/D5.0 Page 2 of 6

3 ECEIVE ELECO-OPICAL CHAACEISICS PAAMEE SYMBOL MIN YP. MAX UNI NOE Maximum Input Optical Power P max -3 dbm Gb/s Minimum Input Optical Power 1.06Gb/s P min 622Mb/s -21 dbm 4 155Mb/s Mb/s Operating Wavelength λ nm Optical eturn Loss OL 14 db eceiver Electrical 3dB Upper Cutoff Frequency MHz LOS of Signal - Asserted P A -35 dbm LOS of Signal - Deasserted P D -20 dbm Loss of Signal -Hysterisis P D -P A 0.5 db Notes: 1. Measured average power coupled into 9/125μm single mode fiber. 2. hese are 20-80% values. 3. Measured with PBS at BE< Measured with PBS at BE<10-10 IMING CHAACEISICS PAAMEE SYMBOL MIN YP. MAX UNI NOE X_DISABLE Assert ime t_off 10 μs X_DISABLE Negate ime t_on 1 ms ime to initialize, include reset of X_FAUL t_init 300 ms X_FAUL from fault to assertion t_fault 100 μs X_DISABLE time to start reset t_reset 10 μs eceiver Loss of Signal Assert ime (off to on) eceiver Loss of Signal Assert ime (on to off) t A,X_LOS 100 μs t D,X_LOS 100 μs Page 3 of 6

4 BLOCK DIAGAM OF ANSCEIVE Electrical Sub-assembly D+ D- LD Driver WDM Optical Sub-assembly X Disable X Fault DFB-LD (0) MOD_DEF Post-Amp (1) (2) D+ D- Pre- Amp Single LC eceptacle Connector X_LOS Page 4 of 6

5 PIN OU DIAGAM OF ANSCEIVE D- 2 x Fault 18 D+ 3 x Disable 17 4 MOD-DEF2 16 V CC 5 MOD-DEF1 15 V CC 6 MOD-DEF ate Select 13 D+ 8 LOS 12 D op of Board Buttom of Board (As Viewed through op of Board PIN OU ABLE Pin Symbol Functional Description 1 Vee ransmitter Ground 2 X Fault ransmitter Fault Indication 3 X Disable ransmitter Disable Module disables on high or open 4 MOD-DEF(2) Module Definition 2 wo wire serial ID interface 5 MOD-DEF(1) Module Definition 1 wo wire serial ID interface 6 MOD-DEF(0) Module Definition 0 Grounded in module 7 ate Select Not Connected 8 LOS Loss of Signal 9 Vee eceiver Ground 10 Vee eceiver Ground 11 Vee eceiver Ground 12 D- Inverse eceived Data Out 13 D+ eceived Data Out 14 Vee eceiver Ground 15 Vcc eceiver Power 16 Vcc ransmitter Power 17 Vee ransmitter Ground 18 D+ ransmitter Data In 19 D- Inverse ransmitter Data In 20 Vee ransmitter Ground Page 5 of 6

6 ECOMMENDED CICUI SCHEMAIC Vcc V CC x Fault x Disable LD Driver 100 D+ D- V CC V CC D- L1 C2 L2 C3 Vcc C1 System Pre Amp Post Amp D+ 100Ω Vcc X_LOS EEPOM MOD-DEF(2) MOD-DEF(1) MOD-DEF(0) Note : 4.7KΩ < < 10KΩ L1, L2 = 1mH C1 =10mF C2, C3 = 0.1mF MECHANICAL DIMENSIONS Units in mm All dimensions are ±0.2mm unless otherwise specified. Page 6 of 6