Key Features & Benefits

Transcription

1 Units in mm All dimensions are ±0.2mm unless otherwise specified. SFP, Duplex LC Connector 1310nm FP LD For Single Mode Fiber Compatible With LNX-0702 Ethernet Switch Description he SFP-S10- is the high performance and cost-effective module for serial optical data communication applications specified for single mode of 1.25 Gb/s. It operates on +3.3V power. he module is intended for single mode fiber, operates at a nominal wavelength of 1310nm, and complies with Multi-Source Agreement (MSA) Small Form Factor Pluggable (SFP). Each module consists of a transmitter optical subassembly, a receiver optical subassembly, and an electrical subassembly. All are housed in a metal package and the combination produces a reliable component. he module is a duplex LC connector transceiver designed for use in Gigabit Ethernet applications and to provide IEEE-802.3z compliant link for 1.25Gb/s intermediate reach applications. he characteristics are performed in accordance with elcordia Specification G-468-COE. Applications Gigabit Ethernet Links Fiber Channel Links at 1.06 Gbps High Speed Backplane Interconnects Switched Backbones Key Features & Benefits 1310nm FP LD Data ate: 1.25Gbps, NZ Single +3.3V Power Supply ohs Compliant and Lead-free AC/AC Differential Electrical Interface Compliant with Multi-Source Agreement (MSA) Small Form Factor Pluggable (SFP) Duplex LC Connector Compliance with specifications for IEEE-802.3z Gigabit Ethernet at 1.25 Gbps Compliance with ANSI specifications for Fiber Channel applications at 1.06 Gbps Eye Safety (Designed to meet Laser Class 1, complies with EN ) EMC Most equipment utilizing high-speed transceivers will be required to meet the following requirements: 1. FCC in the United States 2. CENELEC EN55022 (CISP 22) in Europe o assist the customer in managing the overall equipment EMC performance, the transceivers have been designed to satisfy FCC class B limits and provide good immunity to radio-frequency electromagnetic fields. Eye Saftey he transceivers have been designed to meet Class 1 eye safety and comply with EN el Fax sales@acromag.com Wixom d, Wixom, MI USA Bulletin #

2 Product Information Model Number Operating Voltage & SD Output Distance LD ype & Output Power Sensitivity Wavelength SFP-S10-3.3V L AC/AC 10 km 1310 nm FP -9.5 to -3 dbm -21dBM ABSOLUE MAX AINGS PAAMEE Symbol Min Max Unit Note Storage emperature S C Supply Voltage V CC 0 6 V Data Input Voltage V cc V Supply Current I S 300 ma Operating Conditions PAAMEE Symbol Min YP. Max Unit Note Case Operating emperature A C Supply Voltage V CC V Data Input Voltage Swing V ID mv Electrical Characteristics PAAMEE Symbol Min Max Unit Note ransmitter ransmitter Supply Current I CC 200 ma x_ Disable Input Voltage - Low V IL x_ Disable Input Voltage - High V IH x_ Fault Output Voltage - Low V OL x_ Fault Output Voltage - High V OH eceiver eceiver Supply Current I CC 100 ma eceiver Data Output Differential Voltage V OD V x_los Output Voltage - Low V OL x_los Output Voltage - High V OH MOD_DEF (1), MOD_DEF (2) - Low V IL -0.6 VCC x 0.3 V MOD_DEF (1), MOD_DEF (2) - High V IH VCC x 0.7 VCC V ransmitter Electro-Optical Characteristics PAAMEE Symbol Min YP. Max Unit Note Optical Output Power P O dbm 1 Extinction atio E 9 db Center Wavelength λ c nm 2 Spectral Width (MS) Δλ 3 nm 2 IN IN -117 db/hz Optical ise time (20%-80%) t r 260 ps 3 Optical Fall time (20%-80%) t f 260 ps 3 Output Eye Compliant with IEEE802.3z/D5.0 el Fax sales@acromag.com Wixom d, Wixom, MI USA

3 eceiver Electro-Optical Characteristics PAAMEE Symbol Min YP. Max Unit Note Maximum Input Optical Power P max -3 dbm 4 Minimum Input Optical Power P min -21 dbm 4 Operating Wavelength λ nm Optical eturn Loss OL 12 db eceiver Electrical 3dB Upper Cutoff Frequency MHz LOS of Signal - Asserted P A -35 dbm LOS of Signal - Deasserted P D -20 dbm Loss of Signal -Hysterisis P D - P A 0.5 db Notes: 1. Measured average power coupled into 9/125μm single mode fiber. 2. In conformance with IEEE802.3z Figure 59-3 and FC-PI Figure hese are 20-80% values. 4. Measured with PBS at BE<10-12 iming Characteristics PAAMEE Symbol Min YP. Max Unit Note X_DISABLE Assert ime t_off 10 μs X_DISABLE Negate ime t_on 1 ms ime to initialize, include reset of X_FAUL t_init 300 ms X_FAUL from fault to assertion t_fault 100 μs X_DISABLE time to start reset t_reset 10 μs eceiver Loss of Signal Assert ime (off to on) t A,X_LOS 100 μs eceiver Loss of Signal Assert ime (on to off) t D,X_LOS 100 μs Block Diagram of ransceiver: Electrical Sub-assembly D+ D- LD Driver LD X Disable X Fault (0) (1) (2) MOD_DEF Optical Sub-assembly Duplex LC eceptacle D+ D- Post- Pre- X_LOS el Fax sales@acromag.com Wixom d, Wixom, MI USA

4 Pin Out Diagram of ransceiver D- 2 x Fault 18 D+ 3 x Disable 17 4 MOD-DEF2 16 V CC 5 MOD-DEF1 15 V CC 6 MOD-DEF ate Select 13 D+ 8 LOS 12 D op of Board Buttom of Board (As Viewed through op of Board Pin Out able Pin Symbol Functional Description 1 V ee ransmitter Ground 2 X Fault ransmitter Fault Indication 3 X Disable ransmitter Disable Module disables on high or open 4 MOD-DEF(2) Module Definition 2 wo wire serial ID interface 5 MOD-DEF(1) Module Definition 1 wo wire serial ID interface 6 MOD-DEF(0) Module Definition 0 Grounded in module 7 ate Select Not Connected 8 LOS Loss of Signal 9 V ee eceiver Ground 10 V ee eceiver Ground 11 V ee eceiver Ground 12 D- Inverse eceived Data Out 13 D+ eceived Data Out 14 V ee eceiver Ground 15 V CC eceiver Power 16 V CC ransmitter Power 17 V ee ransmitter Ground 18 D+ ransmitter Data In 19 D- Inverse ransmitter Data In 20 V ee ransmitter Ground el Fax sales@acromag.com Wixom d, Wixom, MI USA

5 ecommended Circuit Schematic Ordering Information VCC VEE x Fault x Disable Models SFP-S Gigabit Fiber SFP ransceiver, Single Mode 10KM / LC / 1310nm, -40 to 85 C Pre LD Driver Post 100 D+ D- D- VCC VCC D+ L1 C2 L2 C3 C1 100Ω System elated Products LNX-0702G-SFP- 7-port Gigabit fiber un-managed switch (2 x SFP 100/1000, 5 x copper 10/100/1000), extended temp (-40 to 80 C) version Ethernet I/O Modules Power Supplies Mounting Accessories X_LOS EEPOM MOD-DEF(2) MOD-DEF(1) MOD-DEF(0) Note :4.7KΩ< < 10KΩ L1, L2 =1µH C1 =10µF C2,C3 = 0.1µF el Fax sales@acromag.com Wixom d, Wixom, MI USA