AVAILABLE OPTIONS FUNCTION

Transcription

1 Low-Cost Single-Channel High-Speed MOSFET Driver I CC...-µA Max (TPS88, TPS89) -ns Max Rise/Fall Times and 0-ns Max Propagation Delay...-nF Load -A Peak Output Current -V to -V Driver Supply Voltage Range; Internal Regulator Extends Range to 0 V (TPS86, TPS87, TPS88, TPS89) -pin SOT- Package 0 C to C Ambient-Temperature Operating Range Highly Resistant to Latch-ups VDD GND IN NC TPS86, TPS87 TPS88, TPS89 DBV PACKAGE (TOP VIEW) TPS88, TPS89 DBV PACKAGE (TOP VIEW) OUT description GND The TPS8xx single-channel high-speed MOS- FET drivers are capable of delivering peak IN OUT currents of up to A into highly capacitive loads. High switching speeds (t r and t f = ns typ) are NC No internal connection obtained with the use of BiCMOS outputs. Typical threshold switching voltages are / and / of V CC. The design inherently minimizes shootthrough current. A regulator is provided on TPS86 through TPS89 devices to allow operation with supply inputs between V and 0 V. The regulator output can be used to power other circuits, provided power dissipation does not exceed package limitations. If the regulator is not required, V DD (the regulator input) should be connected to V CC. The TPS86 and TPS87 input circuits include an active pullup circuit to eliminate the need for an external resistor when using open-collector PWM controllers. The TPS88 and TPS89 are identical to the TPS86 and TPS87, except that the active pullup circuit is omitted. The TPS88 and TPS89 are identical to the TPS88 and TPS89, except that the internal voltage regulator is omitted, allowing quiescent current to drop to less than µa when the inputs are high or low. The TPS8xx series devices are available in -pin SOT- (DBV) packages and operate over an ambient temperature range of 0 C to C. AVAILABLE OPTIONS TA FUNCTION PACKAGED DEVICES CHIP FORM SOT- (DBV) (Y) Inverting driver with active pullup input TPS86DBV TPS86Y Noninverting driver with active pullup input TPS87DBV TPS87Y 0 C to C Inverting driver TPS88DBV TPS88Y Noninverting driver TPS89DBV TPS89Y Inverting driver, no regulator TPS88DBV TPS88Y Noninverting driver, no regulator TPS89DBV TPS89Y The DBV package is available taped and reeled only. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 00, Texas Instruments Incorporated

2 functional block diagram TPS86, TPS88 TPS87, TPS89 VDD VREG VDD VREG Active Pullup (TPS86 Only) Active Pullup (TPS87 Only) IN OUT IN OUT GND GND TPS88 TPS89 IN OUT IN OUT GND GND INPUT STAGE DIAGRAM OUTPUT STAGE DIAGRAM Predrive IN To Drive Stage OUT

3 TPS8xxY chip information This chip, when properly assembled, displays characteristics similar to those of the TPS8xx. Thermal compression or ultrasonic bonding may be used on the doped aluminum bonding pads. The chip may be mounted with conductive epoxy or a gold-silicon preform. BONDING PAD ASSIGNMENTS () () OUT GND IN () () () TPS86Y () () VDD 9 () () () TPS86 through TPS89 only CHIP THICKNESS: TYPICAL BONDING PADS: MINIMUM TJ max = 0 C TOLERANCES ARE ±0%. ALL DIMENSIONS ARE IN MILS. 9 Terminal Functions TPS86, TPS88, TPS88 (inverting driver) TERMINAL NAME NO. DESCRIPTION VDD Regulator supply voltage input. (Not connected on TPS88) GND Ground IN Driver input. OUT Driver output, OUT = IN Driver supply voltage/regulator output voltage TPS87, TPS89, TPS89 (noninverting driver) TERMINAL NAME NO. DESCRIPTION VDD Regulator supply voltage input. (Not connected on TPS89) GND Ground IN Driver input. OUT Driver output, OUT= IN Driver supply voltage/regulator output voltage

4 PACKAGE TA C POWER RATING DISSIPATION RATING TABLE DERATING FACTOR ABOVE TA = C TA = 70 C POWER RATING TA = 80 C POWER RATING DBV 7 mw. mw/ C 80 mw 7 mw These dissipation ratings are based upon EIA specification JESD-, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages, in tests conducted in a zero-airflow, wind tunnel environment. absolute maximum ratings over operating temperature range (unless otherwise noted) Supply voltage range, V CC V to V Regulator supply voltage range, V DD V CC 0. V to V Input voltage range, IN V to V CC +0. V Output voltage range, (pin ) V to V CC +0. V Continuous regulator output current, V CC ma Continuous output current, OUT ±00 ma Continuous total power dissipation See Dissipation Rating Table Operating ambient temperature range, T A C to C Storage temperature range, T stg C to 0 C Lead temperature,6 mm (/6inch) from case for 0 seconds C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE : All voltages are with respect to device GND terminal. recommended operating conditions MIN MAX UNIT Regulator input voltage range, VDD, TPS86 through TPS V Supply voltage, V Input voltage, IN 0. V Continuous regulator output current, ICC 0 0 ma Operating ambient temperature range, TA 0 C

5 TPS8xx electrical characteristics over recommended operating ambient temperature range, V CC = 0 V, V DD tied to V CC, C L = nf (unless otherwise specified) Inputs PARAMETER TEST CONDITIONS MIN TYP MAX UNIT = V. Positive-going input threshold voltage = 0 V V = V 9. 0 = V.7 Negative-going going input threshold voltage = 0 V. V = V..6 Input voltage hysteresis. V Input current, TPS88/9/8/9 Input = 0 V or 0. µa Input current, TPS86/7 Input = 0 V 60 Input = Input capacitance 0 pf Typicals are for TA = C unless otherwise noted. outputs High-level l output t voltage Low-level el output t voltage Typicals are for TA = C unless otherwise noted. regulator, TPS86 through TPS89 Output t voltage Output voltage in dropout Typicals are for TA = C unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT IO = ma IO = 00 ma 8 9. IO = ma IO = 00 ma PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VDD 0 V, 0. 0 IO 0 ma IO = 0 ma, 8 0 VDD = 0 V µaa V V V V supply current PARAMETER TEST CONDITIONS MIN TYP MAX UNIT TPS86, IN = high = 0 V 0 0 TPS87 IN = low = 0 V Supply current into Supply current into VDD Typicals are for TA = C unless otherwise noted. TPS88, TPS89 TPS88, TPS89 IN = high or low, High = 0 V, Low = 0 V TPS86, VDD = 0 V, TPS87 IN = high = 0 V or low = 0 V TPS88, VDD = 0 V, TPS89 IN = high = 0 V or low = 0 V 0 µa µa 0 0

6 TPS8xxY electrical characteristics at T A = C, V CC = 0 V, V DD tied to V CC, C L = nf (unless otherwise specified) Inputs outputs PARAMETER TEST CONDITIONS MIN TYP MAX UNIT = V. Positive-going input threshold voltage = 0 V 6.6 V = V 9. = V.7 Negative-going going input threshold voltage = 0 V. V = V.6 Input voltage hysteresis. V Input current, TPS88/9/8/9 Input = 0 V or 0. µa Input current, TPS86/7 Input = 0 V 60 Input = µaa Input resistance 000 MΩ Input capacitance pf PARAMETER TEST CONDITIONS MIN TYP MAX UNIT High-level l output t voltage IO = ma 9.9 IO = 00 ma 9. V Low-level output voltage IO = ma 0.8 IO = 00 ma V regulator, TPS86 through TPS89 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Output voltage VDD 0 V, 0 IO 0 ma Output voltage in dropout IO = 0 ma, VDD = 0 V. V 9 V supply current PARAMETER TEST CONDITIONS MIN TYP MAX UNIT TPS86, IN = high = 0 V 0 TPS87 IN = low = 0 V 60 Supply current into Supply current into VDD TPS88, TPS89 TPS88, TPS89 IN = high or low, High = 0 V, Low = 0 V TPS86, VDD = 0 V, TPS87 IN = high = 0 V or low = 0 V TPS88, VDD = 0 V, TPS89 IN = high = 0 V or low = 0 V µa µa 0 6

7 switching characteristics for all devices over recommended operating ambient temperature range, V CC = 0 V, V DD tied to V CC, C L = nf (unless otherwise specified) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT = V tr Rise time = 0 V 0 ns r = V = V tf Fall time = 0 V 0 ns f = V = V 0 tphl Propagation delay time, high-to-low-level output = 0 V ns = V 0 = V 0 tplh Propagation delay time, low-to-high-level output = 0 V ns = V 0 PARAMETER MEASUREMENT INFORMATION IN 0% 0% 0 V tf tr OUT 90% 0% 0% 90% 0% 0% 0 V tphl tplh Figure. Typical Timing Diagram (TPS86) 7

8 PARAMETER MEASUREMENT INFORMATION TPS86 Regulator 0. µf + 0 V.7 µf Input Output 0 Ω nf Figure. Switching Time Test Setup TPS Vdc OUT Current Loop + 0. µf.7 µf 0 V Figure. Shoot-Through Current Test Setup 8

9 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Rise time Supply voltage Fall time Supply voltage Propagation time (L>H) Supply voltage 6 Propagation Time (H>L) Supply voltage 7 Rise time Ambient temperature 8 Fall time Ambient temperature 9 Propagation time (L>H) Supply voltage 0 Propagation time (H>L) Ambient temperature Supply current () Supply voltage Supply current () Load capacitance Supply current () Ambient temperature Input threshold voltage Supply voltage Regulator output voltage Regulator supply voltage 6 Regulator quiescent current Regulator supply voltage 7 Shoot-through current Input voltage (L>H) 8 Shoot-through current Input voltage (H>L) 9 9

10 TYPICAL CHARACTERISTICS RISE TIME SUPPLY VOLTAGE TA = C 0 FALL TIME SUPPLY VOLTAGE TA = C Rise Time ns tr CL = 00 pf CL = 000 pf Fall Time ns tf 0 0 CL = 00 pf CL = 000 pf CL = Supply Voltage V Figure CL = Supply Voltage V Figure 0 PROPAGATION DELAY TIME, LOW-TO-HIGH-LEVEL OUTPUT SUPPLY VOLTAGE TA = C 0 PROPAGATION DELAY TIME, HIGH-TO-LOW-LEVEL OUTPUT SUPPLY VOLTAGE TA = C t PLH Propagation Delay Time, Low-To-High-Level Output ns CL = 00 pf CL = 000 pf CL = 0 t PHL Propagation Delay Time, High-To-Low-Level Output ns CL = 00 pf CL = 000 pf CL = Supply Voltage V Figure Supply Voltage V Figure 7 0

11 TYPICAL CHARACTERISTICS 9 8 RISE TIME AMBIENT TEMPERATURE = 0 V Load = 000 pf f = 00 khz FALL TIME AMBIENT TEMPERATURE = 0 V Load = 000 pf f = 00 khz Rise Time ns tr 7 6 Fall Time ns tf Ambient Temperature C Ambient Temperature C Figure 8 Figure 9 t PLH Propagation Delay Time, Low-To-High-Level Output ns PROPAGATION DELAY TIME, LOW-TO-HIGH-LEVEL OUTPUT SUPPLY VOLTAGE = 0 V Load = 000 pf f = 00 khz t PHL Propagation Delay Time, High-To-Low-Level Output ns PROPAGATION DELAY TIME, HIGH-TO-LOW-LEVEL OUTPUT AMBIENT TEMPERATURE = 0 V Load = 000 pf f = 00 khz TA Ambient Temperature C Figure TA Ambient Temperature C Figure

12 TYPICAL CHARACTERISTICS 6 Load = 000 pf Duty Cycle = 0% SUPPLY CURRENT SUPPLY VOLTAGE. = 0 V f = 00 khz Duty Cycle = 0% SUPPLY CURRENT LOAD CAPACITANCE Supply Current ma ICC f = MHz f = 00 khz Supply Current ma ICC.. f = 0 khz f = 00 khz Supply Voltage V CL Load Capacitance pf 000 Figure Figure ICC Supply Current ma.. SUPPLY CURRENT AMBIENT TEMPERATURE = 0 V Load = 000 pf f = 00 khz Duty Cycle = 0% Input Threshold Voltage V INPUT THRESHOLD VOLTAGE SUPPLY VOLTAGE Positive Going Negative Going VIT TA Ambient Temperature C Figure Supply Voltage V Figure

13 TYPICAL CHARACTERISTICS REGULATOR OUTPUT VOLTAGE REGULATOR SUPPLY VOLTAGE REGULATOR QUIESCENT CURRENT REGULATOR SUPPLY VOLTAGE TPS86,7 only No Load Regulator Output Voltage V Load = 0 kω µ A Regulator Quiescent Current VDD Regulator Supply Voltage V Figure VDD Regulator Supply Voltage V Figure SHOOT-THROUGH CURRENT INPUT VOLTAGE LOW-TO-HIGH = 0 V No Load TA = C 7 6 SHOOT-THROUGH CURRENT INPUT VOLTAGE HIGH-TO-LOW = 0 V No Load TA = C Shoot-Through Current ma Shoot-Through Current ma VI Input Voltage V VI Input Voltage V 8 0 Figure 8 Figure 9

14 APPLICATION INFORMATION MOSFETs are voltage-driven devices that require very little steady-state drive current. However, the large input capacitance (00 pf to 000 pf or greater) of these devices requires large current surges to reduce the turn-on and turn-off times. The TPS86 series of high-speed drivers can supply up to A to a MOSFET, greatly reducing the switching times. The fast rise times and fall times and short propagation delays allow for operation in today s high-frequency switching converters. In addition, MOSFETs have a limited gate-bias voltage range, usually less than 0 V. The TPS86 series of drivers extends this operating range by incorporating an on-board series regulator with an input range up to 0 V. This regulator can be used to power the drivers, the PWM chip, and other circuitry, providing the power dissipation rating is not exceeded. When using these devices, care should be exercised in the proper placement of the driver, the switching MOSFET, and the bypass capacitor. Because of the large input capacitance of the MOSFET, the driver should be placed close to the gate to eliminate the possibility of oscillations caused by trace inductance ringing with the gate capacitance of the MOSFET. When the driver output path is longer than approximately inches, a resistor in the range of 0 Ω should be placed in series with the gate drive as close as possible to the MOSFET. A ceramic bypass capacitor is also recommended to provide a source for the high-speed current transients that the MOSFET requires. This capacitor should be placed between V CC and GND of the driver (see Figures 0 and ). TPS86 Regulator 0. µf Load Input Figure 0. V CC < V VDD TPS86 Regulator 0. µf.7 µf + Load Input Figure. V CC > V

15 APPLICATION INFORMATION The on-board series regulator supplies approximately 0 ma of current at. V, some of which can be used for external circuitry, providing the power dissipation rating for the driver is not exceeded. When using the on-board series regulator, an electrolytic output capacitor of.7 µf or larger is recommended. Although not required, a 0.-µF ceramic capacitor on the input of the regulator can help suppress transient currents (see Figure ). When not used, the regulator should be connected to V CC. Grounding V DD will result in destruction of the regulator. VDC 0. µf + 0. µf.7 µf TPS86 PWM Controller Regulator 0. µf GND Out 0 µf VO Figure. Boost Application The TPS86 and TPS88 drivers include active pullup circuits on the inputs to eliminate the need for external pullup resistors when using controllers with open-collector outputs (such as the TL00). The TPS87 and TPS89 drivers have standard CMOS inputs providing a total device operating current of less than 0 µa. All devices switch at standard CMOS logic levels of approximately / V CC with positive-going input levels, and approximately / V CC with negative-going input levels. Being CMOS drivers, these devices will draw relatively large amounts of current (Approximately ma) when the inputs are in the range of one-half of the supply voltage. In normal operation, the driver input is in this range for a very short time. Care should be taken to avoid use of very low slew-rate inputs, used under normal operating conditions. Although not destructive to the device, slew rates slower than 0. V/µs are not recommended. The BiCMOS output stage provides high instantaneous drive current to rapidly toggle the power switch, and very low drop to each rail to ensure proper operation at voltage extremes. Low-voltage circuits (less than V) that require very low quiescent currents can use the TPS88 and TPS89 drivers. These drivers use typically 0. µa of quiescent current (with inputs high or low). They do not have the internal regulator or the active pullup circuit, but all other specifications are the same as for the rest of the family..-v/.-v, -A application Figure illustrates the use of the TPS87 with a TL00 PWM controller and a TPS0 in a simple step-down converter application. The converter operates at 7 khz and delivers either. V or. V (determined by the value of R6) at A ( A peak) from a -V supply. The bill of materials is provided in Table.

16 APPLICATION INFORMATION. V to 7 V C7 + C8 Q TPS0D L VO A Continuous A Peak U TPS87DBV R + + C Regulator CR C9 C0 C C GND GND U TL00CD OUT + C6 SCP R C R6 R7 GND 8 C9 R DTC COMP FB RT 6 7 C C R R C Figure. Step-Down Application NOTE: If the parasitics of the external circuit cause the voltage to violate the Absolute Maximum Rating for the Output pins, Schottky diodes should be added from ground to output and from output to Vcc. 6

17 APPLICATION INFORMATION Table. Bill of Materials REF DES PART NO. DESCRIPTION MFR U TPS87DBV IC, MOSFET driver, single noninverting TI U TL00CD IC, PWM controller TI Q TPS0D MOSFET, p-channel, 6 A, 7 V, 7 mω TI C, C, C, C8 Capacitor, ceramic, 0. µf, 0 V, X7R, 06 C Capacitor, ceramic, 0.0 µf, 0 V, X7R, 06 C Capacitor, ceramic, 00 pf, 0 V, X7R, 080 C6 ECS-TCY0R Capacitor, tantalum,.0 µf, 6 V, A case Panasonic C7 0SC7M Capacitor, OS-Con, 7 µf, 0 V Sanyo C9 Capacitor, ceramic, 000 pf, 0 V, X7R, 080 C0, C 0SA0M Capacitor, OS-Con, 0 µf, 0 V Sanyo C Capacitor, ceramic, 0.0 µf, 0 V, X7R, 080 C Capacitor, ceramic, 7 µf, 0 V, X7R CR 0WQ0F Diode, Shottky, D-pak, A 0 V IR L SML7 Inductor, 7 µh, +/ 0%, A Nova Magnetics R Resistor, CF, 7 kω, /0 W, %, 080 R Resistor, CF,. kω, /0 W, %, 080 R Resistor, MF, 0. kω, /0 W, %, 080 R Resistor, MF,.00 kω, /0 W, %, 080 R Resistor, CF, 7 Ω, /0 W, %, 080 R6 (.-V) Resistor, MF,. kω, /0 W, %, 080 R6 (.-V) Resistor, MF,.0 kω, /0 W, %, 080 R7 Resistor, CF, 00 Ω, /0 W, %, 080 As shown in Figures and, the TPS87 turns on the TPS0 power switch in less than 0 ns and off in ns. Q Gate V/div Q Drain V/div Q Drain V/div Q Gate V/div. ns/div. ns/div Figure. Q Turn-On Waveform Figure. Q Turn-Off Waveform 7

18 APPLICATION INFORMATION The efficiency for various output currents, with a.-v input, is shown in Figure 6. For a.-v output, the efficiency is greater than 90% for loads up to A exceptional for a simple, inexpensive design VO =. V VI =. V TA = C Efficiency % 8 80 VO =. V Load Current A Figure 6. Converter Efficiency 8

19 DBV (R-PDSO-G) MECHANICAL DATA PLASTIC SMALL-OUTLINE PACKAGE 0,0 0,9 0, M 0,0,80,0,00,0 0, NOM,0,70 Gage Plane 0, 0 8,0,00 0,0 MIN Seating Plane 0,0 07-/B /96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions include mold flash or protrusion. 9

20 PACKAGE OPTION ADDENDUM -Dec-009 PACKAGING INFORMATION Orderable Device Status () Package Type Package Drawing Pins Package Qty Eco Plan () Lead/Ball Finish MSL Peak Temp () TPS86DBV OBSOLETE SOT- DBV TBD Call TI Call TI TPS86DBVR ACTIVE SOT- DBV 000 Green (RoHS & TPS86DBVRG ACTIVE SOT- DBV 000 Green (RoHS & TPS86DBVT ACTIVE SOT- DBV 0 Green (RoHS & TPS86DBVTG ACTIVE SOT- DBV 0 Green (RoHS & TPS87DBV OBSOLETE SOT- DBV TBD Call TI Call TI TPS87DBVR ACTIVE SOT- DBV 000 Green (RoHS & TPS87DBVRG ACTIVE SOT- DBV 000 Green (RoHS & TPS87DBVT ACTIVE SOT- DBV 0 Green (RoHS & TPS87DBVTG ACTIVE SOT- DBV 0 Green (RoHS & TPS88DBV OBSOLETE SOT- DBV TBD Call TI Call TI TPS88DBVR ACTIVE SOT- DBV 000 Green (RoHS & TPS88DBVRG ACTIVE SOT- DBV 000 Green (RoHS & TPS89DBV OBSOLETE SOT- DBV TBD Call TI Call TI TPS89DBVR ACTIVE SOT- DBV 000 Green (RoHS & TPS89DBVRG ACTIVE SOT- DBV 000 Green (RoHS & TPS89DBVT ACTIVE SOT- DBV 0 Green (RoHS & TPS89DBVTG ACTIVE SOT- DBV 0 Green (RoHS & TPS88DBV OBSOLETE SOT- DBV TBD Call TI Call TI TPS88DBVR ACTIVE SOT- DBV 000 Green (RoHS & TPS88DBVRG ACTIVE SOT- DBV 000 Green (RoHS & TPS88DBVT ACTIVE SOT- DBV 0 Green (RoHS & TPS88DBVTG ACTIVE SOT- DBV 0 Green (RoHS & TPS89DBV OBSOLETE SOT- DBV TBD Call TI Call TI TPS89DBVR ACTIVE SOT- DBV 000 Green (RoHS & TPS89DBVRG ACTIVE SOT- DBV 000 Green (RoHS & TPS89DBVT ACTIVE SOT- DBV 0 Green (RoHS & Addendum-Page

21 PACKAGE OPTION ADDENDUM -Dec-009 Orderable Device Status () Package Type Package Drawing Pins Package Qty TPS89DBVTG ACTIVE SOT- DBV 0 Green (RoHS & Eco Plan () Lead/Ball Finish MSL Peak Temp () () The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. () Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & - please check for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either ) lead-based flip-chip solder bumps used between the die and package, or ) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & : TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.% by weight in homogeneous material) () MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS86, TPS87, TPS88, TPS89, TPS88, TPS89 : Automotive: TPS89-Q Enhanced Product: TPS86-EP, TPS87-EP, TPS88-EP, TPS89-EP, TPS88-EP, TPS89-EP NOTE: Qualified Version Definitions: Automotive - Q00 devices qualified for high-reliability automotive applications targeting zero defects Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page

22 PACKAGE MATERIALS INFORMATION 9-Jul-008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Reel Diameter Width (mm) W (mm) A0 (mm) B0 (mm) K0 (mm) P (mm) TPS86DBVR SOT- DBV Q TPS86DBVT SOT- DBV Q TPS87DBVR SOT- DBV Q TPS87DBVT SOT- DBV Q TPS88DBVR SOT- DBV Q TPS89DBVR SOT- DBV Q TPS89DBVT SOT- DBV Q TPS88DBVR SOT- DBV Q TPS88DBVT SOT- DBV Q TPS89DBVR SOT- DBV Q TPS89DBVT SOT- DBV Q W (mm) Pin Quadrant Pack Materials-Page

23 PACKAGE MATERIALS INFORMATION 9-Jul-008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS86DBVR SOT- DBV TPS86DBVT SOT- DBV TPS87DBVR SOT- DBV TPS87DBVT SOT- DBV TPS88DBVR SOT- DBV TPS89DBVR SOT- DBV TPS89DBVT SOT- DBV TPS88DBVR SOT- DBV TPS88DBVT SOT- DBV TPS89DBVR SOT- DBV TPS89DBVT SOT- DBV Pack Materials-Page

24 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 699 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio /audio Data Converters dataconverter.ti.com Automotive /automotive DLP Products Broadband /broadband DSP dsp.ti.com Digital Control /digitalcontrol Clocks and Timers /clocks Medical /medical Interface interface.ti.com Military /military Logic logic.ti.com Optical Networking /opticalnetwork Power Mgmt power.ti.com Security /security Microcontrollers microcontroller.ti.com Telephony /telephony RFID Video & Imaging /video RF/IF and ZigBee Solutions /lprf Wireless /wireless Mailing Address: Texas Instruments, Post Office Box 60, Dallas, Texas 76 Copyright 009, Texas Instruments Incorporated