F²MC-8FX FAMILY MB95F200 SERIES. LED Control Reference Solution 8-BIT MICROCONTROLLER APPLICATION NOTE

Transcription

1 Fujitsu Microelectronics (Shanghai) Co., Ltd. Application Note MCU-AN E-10 F²MC-8FX FAMILY 8-BIT MICROCONTROLLER MB95F200 SERIES LED Control Reference Solution APPLICATION NOTE

2 Revision History Date Author Change of Records Kevin Lin V1.0 This manual contains 13 pages. 1. The products described in this manual and the specifications thereof may be changed without prior notice. To obtain up-to-date information and/or specifications, please contact your Fujitsu sales representative or Fujitsu authorized dealer. 2. Fujitsu will not be liable for infringement of copyright, industrial property right, or other rights of a third party caused by the use of information or drawings described in this manual. 3. The contents of this manual may not be transferred or copied without the express permission of Fujitsu. 4. The products contained in this manual are not intended for use with equipment which requires extremely high reliability such as aerospace equipment, undersea repeaters, nuclear control systems or medical equipment for life support. 5. Some of the products described in this manual may be strategic materials (or special technology) as defined by the Foreign Exchange and Foreign Trade Control Law. In such cases, the products or portions thereof must not be exported without permission as defined under the law Fujitsu Microelectronics (Shanghai) Co., Ltd. MCU-AN E-10 Page 2

3 CONTENTS Revision History Outline Demo Platform Functions Tune the light down Tune the light up Hardware System Block Schematic Pin Assignment Firmware Flow Chart Files Description Source Code More Information Appendix MCU-AN E-10 Page 3

4 1 Outline LED is widely used in many fields now. In order to achieve higher efficiency or better illumination, the light is usually required to have diming function. There are two ways to dim the LED: one is reducing the drive current, and another is tuning on and off LED drive IC using the low frequency PWM signal. This demo chooses the second way. This demo supports such features: Dim the LED by turn on and off the LED drive IC Change the PWM duty by potentiometer easily MCU-AN E-10 Page 4

5 2 Demo Platform This demo set is based on MB95F212K an 8 pins MCU. The MCU will generate a PWM signal to the LED drive IC to dim LED. The potentiometer decides the PWM duty. Figure 2.1 shows the demo. Figure 2. 1 LED Diming Demo Board MCU-AN E-10 Page 5

6 3 Functions 3.1 Tune the light up User can turn the potentiometer to tune the light up. 3.2 Tune the light down Figure 3. 1 LED at High Luminance User can turn the potentiometer to tune the light down. Figure 3. 2 LED at Low Luminance MCU-AN E-10 Page 6

7 4 Hardware 4.1 System Block Figure 4.1 shows the system block of the demo. Potenti ometer Debug MCU PWM LED drive IC LED module Interfa ce 4.2 Schematic Figure 4. 1 System Block Diagram Figure 4.2(next page) shows the hardware of this demo. The main parts are MB95F212 and T6322A. The P04 is connected to a potentiometer which is used control the PWM duty. The P05 is PWM output pin and is connected to the EN pin of LED drive IC. When P05 outputs H, the IC will output maximum current to the LED module. When P05 outputs L, the IC will shut down, and the LED module is off. 4.3 Pin Assignment Table 4.1 shows MB95F212 pin assignment. Number Pin Function 5 P04 Potentiometer input for PWM duty control 6 P05/TO00 Low frequency PWM 7 P06 Null 8 P12/DBG Debugger port Table 4. 1 MCU Pin Assignment Table 4.2 shows the T6322A pin assignment. Number Pin Function 1 LX Switch signal output 2 GND GND 3 ADJ Null 4 SENSE Current feedback input 5 EN Enable signal input 6 VIN Power input Table 4. 2 LED Driver IC Pin Assignment MCU-AN E-10 Page 7

8 Figure 4. 2 LED Diming Board MCU-AN E-10 Page 8

9 5 Firmware 5.1 Flow Chart The main function of this firmware is sampling voltage and generating PWM signal. The flow chart is shown as Figure 5.1. Start Initial MCU Initial Time00 for PWM Initial AD Sample voltage and update the PWM duty Figure 5. 1 Main Function Flow Chart 5.2 Files Description Functions MCU_ initialization() PWM_init() io_ad_init() ad_sample() Description Initialize MCU Initialize timer00 for PWM Initialize AD module Sample voltage and update the PWM duty Table 5. 1 File Description MCU-AN E-10 Page 9

10 5.3 Source Code MCU-AN E-10 Page 10

11 MCU-AN E-10 Page 11

12 6 More Information For more information on FUJITSU MB95200 products, please visit following website: Simplified Chinese Version MCU-AN E-10 Page 12

13 7 Appendix Figure 2. 1 LED Diming Demo Board... 5 Figure 3. 1 LED at High Luminance... 6 Figure 3. 2 LED at Low Luminance... 6 Figure 4. 1 System Block Diagram... 7 Figure 4. 2 LED Diming Board... 8 Figure 5. 1 Main Function Flow Chart... 9 Table 4. 1 MCU Pin Assignment... 7 Table 4. 2 LED Driver IC Pin Assignment... 7 Table 5. 1 File Description... 9 MCU-AN E-10 Page 13