DPM Modules For DPM 4000 Matrix Manager

Transcription

1 PM Modules For PM 000 Matrix Manager General escription: The PM 000 allows for audio and system expansion through the use of interface card modules. There are three basic types of modules available for the PM000. They are: udio Input Modules udio Output Modules GPIO Control Modules Slots and, located on the far right of the PM 000 (as viewed from the rear), are the PM 000's audio input module slots providing two audio inputs per slot. Each slot can be equipped with any suitable audio input module. The PM 000 is shipped with no audio input modules installed. Slots and, located to the left of slots and, are the PM 000's audio output slots providing two audio outputs per slot. Each slot can be equipped with a - channel audio output module. The PM 000 is shipped with a -channel audio output module installed in slot with slot being left empty. Slot 5, located to the left of slots and, is a control slot, which can be equipped with control modules for general control and query purposes. Control modules provide different kinds of control inputs and outputs. The PM 000 is shipped with one 8 channel I/O control module installed. In addition, an extension slot allows retrofitting additional serial ports, which can be used for the intercommunication amongst PM 000 managers or to connect additional external devices. For detailed information, please refer to the owner s manuals of the individual extensions or modules. -Channel Paging Station Module (NS 905) PM - PCI This -channel audio input module is meant for the connection of PC PC 000 IN 000 Series paging consoles. Each of the two input channels provide J-5 sockets allowing the connection of up to paging stations plus paging station PC 000 IN extensions per input. The microphone terminals are interconnected via 6-conductor parallel cables. The module can be installed in slot and slot.next to the electronically balanced audio input, each input connector 905 provides a serial S-85 interface port and the power supply connection for the paging stations (see also: pin-assignment of the J-5 connector). The paging stations' power supply employs an electronic, programmable fuse, through which the maximum output current can be matched to meet actual system accommodations. This prevents the entire installation from malfunction, in case of shortcircuit occurring in a single paging station only. Input channels can be switched separately onto the monitor bus and you can monitor the audio signal via headphones or loudspeaker, either which is connected to the monitor output. utomatic pilot tone surveillance of the entire input stage is integrated as well. If necessary, retrofitting the audio inputs with transformers is possible. connection x J-5 sockets inputs, electronically balanced nominal input level 0 du / 775 mv max. input level + du / V input impedance 0 kω input balancing > -0 d > 00 d (-ed) distortion < 0.0 % /-conversion 8-bit linear, Sigma-elta control interfaces x S-85 standard power supply outputs for the PC 000, short-circuit-proof, electronically programmable fuses supply voltage V C ( V C) nominal current 0 m, 660 m, 990 m (adjustable, electronic fuse) power consumption W dimensions W x H x 7.5 x 8 x 8 mm 5 g

2 + UX Input Module (NS 906) This -channel audio input module is meant for the connection of external audio sources of any kind. Channel employs two switched UXinputs with C-type connectors ( x / ) for C players, tape decks, tuners, T decks, etc. The / -input of channel is provided through an X F- type connector allowing the connection of microphones, mixers and other similar sources. The module can be inserted in slot and slot.input levels of both UXinputs can be separately adjusted via internal potentiometers in a range between 0 du to + du. The / -input's sensitivity can also be adjusted through an internal / switch (P) providing 0 d attenuation. The GIN-control on the appliance's rear panel offers additional control within a range of 0 d. The / input is electronically balanced and can be retrofitted with a transformer. Phantom power can be switched via a jumper. If necessary, it is also possible to incorporate a compressor/limiter into the audio path via jumper setting. The input channels can be switched separately to the monitor bus and you can listen to the signal via headphones or loudspeaker, either which is being connected to the monitor output. utomatic pilot tone surveillance of the entire input stage is integrated as well. Connections Input PM - M nominal input level max. input level input impedance input nominal input level UX IN UX IN IN GIN 906 x XF-type / x C-type connectors x UX, unbalanced, internally summed -0 du... + du / 50 mv... V + du / V 0 kw, electronically balanced : -5 du... - du /.5 mv mv : - du du / 50 mv... 5 V max. input level : +5 du /. V (im limiter operation) :+0 du / 5 V input impedance :.6 kw, : 0 kw input balancing > -0 d phantom power V / 0 m, switched via jumper > 95 d (-ed) distortion < 0.0 % /-conversion 8-bit linear, Sigma-elta power consumption. W dimensions W x H x 7.5 x 8 x 5 mm 60 g -Channel Input Module (NS 907) PM - MI GIN IN IN GIN 907 This -channel audio input module is meant for the connection of external audio sources, like microphones, mixers, etc. oth channels are furnished with X F-type connectors. The module can be installed into slot and slot.the sensitivity of the / inputs can be adjusted in a wide range. The internal / switches (Ps) provide 0 d attenuation. The separate GIN-controls for each channel provide additional control in a range of 0 d. The / inputs are electronically balanced and can be retrofitted with transformers. Phantom power can be switched via jumper setting. If necessary, compressors / limiters can also be incorporated in the audio paths via jumpers. Input channels can be switched separately onto the monitor bus and you can listen to the signal via headphones or loudspeaker, either which is being connected to the monitor output. utomatic pilot tone surveillance of the entire input stage is integrated as well. x XF-type connectors audio inputs x electronically balanced nominal input level :-5 du... - du /.5 mv mv :- du du / 50 mv... 5 V max. input level :+5 du /. V (in limiter operation) :+0 du / 5 V input impedance :.6 kw : 0 kw Input balancing > -0 d phantom power V / 0 m, switched via jumper > 95 d (-ed) istortion < 0.0 % /-conversion 8-bit linear, Sigma-elta phantom power V / 0 m, switched via jumper power consumption W dimensions W x H x 7.5 x 8 x 5 mm 60 g - -

3 -Channel UX Input Module (NS 908) PM - UX UX IN UX IN UX IN UX IN 908 This -channel audio input module provides 8 C-type connectors ( x / ) for connecting external audio sources such as C-players, tape decks, tuners, T decks, etc. The module can be installed into slot and slot.the input levels of the four UX inputs can be independently adjusted in a range between -0 du and + du via internal trimpotentiometers. Input channels can be switched separately to the monitor bus and you can listen to the signal via headphones or loudspeaker, either which being connected to the monitor output. utomatic pilot tone surveillance of the entire input stage is integrated as well. 8 x C-type connectors inputs x UX, unbalanced, internally summed nominal input level -0 du... + du / 50 mv... V max. input level + du / V input impedance 0 kw > 00 d (-ed) distortion < 0.0 % /-conversion 8-bit linear, Sigma-elta power consumption. W operational +5 C C temperature range dimensions W x H x 7.5 x 8 x 5 mm 50 g + Paging Station Module (NS 90) Specifications This -channel audio input module is meant for the connection of PC 000 Series paging stations and other external audio sources. The J-5 socket of channel allows the connection of up to microphone terminals plus paging station extensions. The / input of channel is furnished through an X F- type connector allowing the connection of microphones, mixers and other audio signal sources. The module can be installed into slot and slot.next to the electronically balanced audio input, the PC 000 input connector provides a serial S-85 interface and the power supply for the connected paging consoles (see also pin-assignment of the J-5 connector). The / input employs an internal switch (P) providing 0 d of attenuation. The GIN-control located on the appliance's rear panel offers additional control in a range of 0 d. The input is electronically balanced and prepared for retrofitting a transformer. Phantom power can be switched via jumper. If necessary, a compressor / limiter circuit can be incorporated in the audio path. : x J-5 socket; x X F-type connector input PC 000, electronically balanced nominal input level 0 du / 775 mv max. input level + du / V input impedance 0 kw input, electronically balanced nominal input level : -5 du... - du /.5 mv mv :- du du / 50 mv... 5 V max. input level : + 5 du /. V (in limiter operation) :+0 du / 5 V input impedance :.6 kw :0 kw Phantom power V / 0 m, switched via jumper input balancing > -0 d > 95 d (-ed) distortion < 0.0 % /-conversion 8-bit linear, Sigma-elta control interface x S-85 standard supply output for the, short-circuit-proof, electronic, PC 000 programmable fuse supply voltage V C ( V C) nominal current 0 m, 660 m, 990 dimensions W x H x 7.5 x 8 x 5 mm 65 g - -

4 -Channel Output Module (NS 908) The output module is meant PM - OUT for the connection of power amplifiers with an input sensitivity of 0 d or +6 d. Two X M-type connectors allow the connection of up to 0 power amplifiers each. The audio signal is OUT electronically balanced; if 0/+6 du necessary, transformers can be retrofitted. The module can be installed in slot or slot. The output channels can be switched separately to the monitor bus and you OUT can listen to the signal via 0/+6 du headphones or loudspeaker, either which is connected to the monitor output. 908 utomatic pilot tone surveillance of the two output channels is also integrated. The jumpers for adjusting the output voltage to 0 d or +6 d are located on the printed board assembly. t the same time you have to alter the jumper setting of the monitor signal correspondingly. The output module employs integrated output relays that prevent switching noise from being heard. When switching the system on, the output signal is put through after the system is been initialized (power-on delay); the contacts are immediately interrupted when switching the power off. Specifications : x XM-type connectors outputs, electronically balanced, transformers are optionally available nominal output level 0 du / 775 mv or +6 du /.55 V, switched via jumper output impedance 5 W dynamic range > 97 d (-ed) > 09 d (-ed) distortion % /-conversion 0-bit linear, Sigma-elta power consumption.5 W dimensions W x H x 7.5 x 8 x 7 mm 60 g 8 I/O Control Module (NS 909) This control module provides 8 floating control inputs and 7 floating logic level outputs (0 V, V). n additional output provides pole change impulses for controlling slave system clocks. Contact is established via x J-5 sockets providing 8 contacts each. The module can be installed in slot 5. The slave clock output (NU, OUT ) is short-circuit proof; up to approximately 0 slave clocks can be connected. Please make sure to connect all slave clocks according to their correct polarity. The control outputs (OUT - 8) are capable of switching voltages of either polarity and up to a maximum current of. The control inputs (IN - 8) are capable of handling voltages of either polarity between - V and + V; for voltages between 0 and 5 V the inputs are not active (low), for voltages between 0 V and V the inputs are active (high). The control inputs can ignite switching functions or macros either during a change of state or in any stationary state. This offers the possibility to monitor line idling currents (e. g. in fire alert system installations). x J-5 sockets logic inputs 8, floating via opto-coupler, bi-polar voltage when the input is UIN < ± 5 V OW voltage when the input is UIN > ± 0 V HIGH maximum input voltage UIN max = ± V logic outputs 7, floating via relay contacts contact capacity / V C slave clock output pole change impulse / turning impulse output voltage V C maximum output current 500 m, electronically protected against overload power consumption. W dimensions W x H x 7.5 x 8 x 7 mm 95 g - -

5 vailable ccessories: Model Cat. No. escription NS NS NS90 68 Output Transformer ine alanced ine alanced Input Transformer ( pc. required per channel) Input Transformer Mic/ine Ordering Information: Model Cat. No. escription NS NS NS NS NS NS90 76 Input Paging Station Module PC Input Module: Mic/ine + x ux Input Module: Mic/ine Channel Output ine Module Input Module: Channel ux (C Phono Connectors) Input Module: Combination Mic/ine + Paging Console lock iagrams: EECTONIC POGMME FUSES +U +V -V NOG PC 000 IN V S-85 UIO NS 9008 X85 TX85 INTEN MONITO MON PIOT PIOT MCK CK WCK IN CHNNE UIO PIOT CONTO PC 000 IN V S-85 UIO ES NS 9008 STTUS & I NS905 lock iagram - 5 -

6 lock iagrams: UX UX GIN UX +V +V -V NOG IN UX GIN MON INTEN MONITO UX UX PIOT PIOT MCK CK WCK IN CHNNE UIO +V IN JP PIOT GIN CONTO ES NS 90 JP IN COMP JP 5 6 STTUS & I COMPESSO / IMITE NS906 lock iagram +V IN JP GIN +V +V -V NOG NS 90 JP IN COMP PIOT INTEN MONITO COMPESSO / IMITE PIOT MON MCK CK WCK IN CHNNE UIO +V JP PIOT CONTO IN GIN ES NS 90 JP IN COMP JP / 5 6 / 5 6 JP STTUS & I COMPESSO / IMITE NS907 lock iagram - 6 -

7 lock iagrams: UX UX GIN UX +V +V -V NOG IN UX GIN MON INTEN MONITO UX UX PIOT PIOT MCK CK WCK IN CHNNE UIO PIOT CONTO UX GIN UX UX ES IN UX GIN STTUS & I UX UX NS908 lock iagram EECTONIC POGMME FUSE +U +V -V NOG PC 000 IN V S-85 UIO NS 9008 X85 TX85 INTEN MONITO PIOT MON PIOT MCK CK WCK IN CHNNE UIO +V IN JP PIOT GIN CONTO ES NS 90 JP IN COMP JP 5 6 STTUS & I COMPESSO / IMITE NS90 lock iagram - 7 -

8 lock iagrams: +U NOG +V -V NS 907 OUT +6d JP. 0d INTEN MONITO +6d 0d MON MUTE CHNNE UIO MCK CK WCK OUT JP. 5 OUT NS 907 CONTO +6d JP. 0d +6d 0d MUTE ES JP. I NS908 lock iagram IN +U IN IN IN IN5 INPUT EGISTE T US 8-5 IN6 IN7 IN8 CONTO SVE COCK CONTO OUT OUT ES OUT OUT5 OUTPUT EGISTE STTUS & I OUT6 OUT7 OUT8 NS909 lock iagram 000 Portland v. South, urnsville, MN 557 Phone: , Fax: Telex Communications Inc /00 Part Number 809-xxx ev US and Canada Only. For customer orders contact Customer Service at: 800/9-97 Fax: 800/955-68