The GNSS-CONTROL System has been designed in house by Position-Control and is the result of over 15 years experience using different Sensor Systems.

Size: px

Start display at page:

Download "The GNSS-CONTROL System has been designed in house by Position-Control and is the result of over 15 years experience using different Sensor Systems."

Annabel Bates
6 years ago
Views:

GNSS Control BASE 1 Robust fanless GNSS System The GNSS-CONTROL System has been designed in house by Position-Control and is the result of over 15 years experience using different Sensor Systems.

RS 485 input ports. It can be managed by System Software.

1 GNSS Control BASE 1 Robust fanless GNSS System The GNSS-CONTROL System has been designed in house by Position-Control and is the result of over 15 years experience using different Sensor Systems. GNSS-CONTROL is a versatile, cost effective and high accuracy Positioning System supporting RTK post-processing positioning. GNSS BaseSystems has a complete Computer Interface on board. RS 485 input ports. It can be managed by System Software. Destination Maschine surveillance Structural monitoring Mining exploration Deep excavation Landslide safety implementation Retaining walls Geotechnical investigation Features 1x LAN Ethernet, 1x USB and 1x RS232, 1x RS 485 Comm ports High performances (resolution, accuracy, environment -20 C +80 C) 4GB RAM internal memory Stand alone or part of network POCO ADC built-in interface Modbus ASCII digital sensors support Option: Hatanaka file compression Meet the essential requirements

2 Technisches Datenblatt GNSS Control Base/Rover 1 POST PROCESSING Statisch Post Processing [18h] H:± 3mm+0.5ppm V:± 5mm+0.5ppm COMMONICATION M8 4 PIN USB und RS232 Seriell PROTOKOLL RTK Datenprotokolle RINEX-Ausgabe OPEN RTK NMEA 0183 V 4.00 und RINEX MODEMS HSDPA Modem (optional) Funkmodem (optional) Voll integriertes Modem mit interner oder externer Antenne Voll integriertes Sende-/Empfangsmodem 868 Mhz mit interner oder externer Antenne, externe Antenne EXTERNAL DATACONNECTION GSM / GPRS / HSDPA / 868 GHz Modem TECHNOLOGIE DATAMANAGEMENT Simultanous GPS/QZSS, GLONASS, BeiDou Branchenführende Navigationsempfindlichkeit von 167 dbm Bis zu 18 Hz Navigation Rate MAIL to sent Alarms to unlimeted users SMS to sent to unlimeted telephone numbers RAW Data Output, NMEA 0183, RINEX 2.1 Optional: Hatanaka Compression Languages: German and English PHYSICAL CHARACTERISTICS Dimensions (L x W x H) Weight Material Wiring 160 x 120 x 120 mm 1500 grams anodized Aluminium /ABS Case IP 67 Removable connector, M8 4 Pin

3 Features Receiver type 72-channel engine GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 SBAS L1 C/A: WAAS, EGNOS, MSAS Galileo-ready E1B/C Max nav. update rate Single GNSS: up to 18 Hz Concurrent GNSS: up to 10 Hz Accuracy Position: 2.5 m CEP SBAS: 2.0 m CEP 1 Acquisition Cold starts: 27 s Aided starts: 4 s Reacquisition: 1 s 1 Sensitivity Tracking and Nav: 164 dbm Cold starts: 147 dbm Hot starts: 156 dbm Assistance GNSS Oscillator AssistNow Online AssistNow Offline AssistNow Autonomous OMA SUPL & 3GPP compliant Crystal Real time clock (RTC) Can be derived either from onboard GNSS crystal (for lowest system costs and smallest size) or from external RTC Clock (Default mode, for lower battery current) Anti jamming SQI Flash (optional) for Active CW detection and removal FW update AssistNow Offline AssistNow Autonomous 2 Supported antennas Active and passive Antenna supervision Short and open circuit detection Electrical data Supply Digital I/O voltage level Power Consumption voltage 9 V to 24 V 1.65 V to 3.6 V 85 3 V (Continuous) Interfaces Serial interfaces Digital I/O 1 UART 1 USB Configurable timepulse 1 EXTINT input for Wakeup Timepulse Configurable 0.25 Hz to 10 MHz Protocols RINEX, UBX binary, RTCM Model Type Supply Interfaces Features Grade GPS / QZSS GLONASS Galileo BeiDou Timing Dead Reckoning Precise Point Positioning Raw Data 1.65 V 3.6 V Lowest power (DC/DC) UART USB SPI DDC Programmable (Flash) Data logger Additional SAW Additional LNA RTC crystal Internal oscillator Active antenna / LNA supply Active antenna / LNA control Antenna short circuit detection / protection pin Antenna open circuit detection pin Frequency output IP 65 IP 67 IP 68 GNSS Base C

4 Environmental data, quality & reliability Operating temp. 40 C to 85 C Storage temp. 40 C to 105 C RoHS compliant (lead-free) and green (no halogens) Qualification according to standard JESD47 Manufactured in ISO/TS certified production sites Moisture sensitivity level 3 Support products GNSS CONTORL HSPDA: GNSS CONTROL 868: Receiver with integrated HSDPA-Modem Receiver with integrated Long Range 868 GHz-Modem Product variants GNSS Base 1 GNSS Rover 1 Concurrent GNSS LGA module,rtk crystal, ROM (Default: GPS + GLONASS) POCO GNSS Server Interface Concurrent GNSS LGA module,rtk crystal, ROM (Default: GPS + GLONASS) POCO GNSS Server Interface Rover s rela ve distance from Base is accurate to millimeter level POCO GNSS Server-Postprocessing [18hours] Base Rover

5 Baseline vs Accuracy Rover Antenna: TW3450 Test Environment: Open Sky Mode: Post Processing Baseline: 190 m Baseline 0.5km TTFF 1 minute Baseline 1km TTFF 1.5 minutes Accuracy 0.5 cm Post Processing Modus 1h RAW DATA

6 Baseline vs Scantime Rover Antenna: TW3450 Test Environment: Open Sky Mode: Post Processing Baseline: 190 m Accuracy 0.35 cm Post Processing Modus 4 h RAW DATA

7 Baseline vs Scantime Rover Antenna: TW3450 Test Environment: Open Sky Mode: Post Processing Baseline: 190 m Accuracy 0.3 cm Post Processing Modus 24 h RAW DATA

Hyperion NEO-M8N GPS

Hyperion NEO-M8N GPS Hyperion M8N GPS Product description The M8 series of concurrent GNSS modules is built on the high performing M8 GNSS engine in the industry proven NEO form factor. The M8 modules utilize concurrent reception