1 Overview. Pressure Measurement Transmitters for gauge pressure for the paper industry. 1/72 Siemens FI US Edition

Transcription

1 Siemens AG 207 Overview Benefits High quality and service life High reliability even under etreme chemical and mechanical loads, e.g. abrasion. For aggressive and non-aggressive gases, vapors and liquids Etensive diagnosis and simulation functions Minimum conformity error Small long-term drift Wetted parts made of Hastelloy Infinitely adjustable span from 0.0 bar to bar (0.4 psi to 22 psi) for DS III with HART interface Nominal measuring range from bar to bar (4.5 psi to 22 psi) for DS III with PROFIBUS PA and FOUNDATION Fieldbus interface Infinitely adjustable span from 0.0 bar to bar (0.4 psi to 22 psi) for SITRANS P00 with HART interface Nominal measuring range from bar to bar (4.5 psi to 22 psi) for SITRANS P00 with PROFIBUS PA interface High measuring accuracy Parameterization over control keys and HART Communication, or over PROFIBUS PA or FOUNDATION Fieldbus interface (DS III only). SITRANS P DS III and P00 with PMC connection - Technical description The SITRANS P00 and DS III pressure transmitters have been fitted with special process connections for the paper industry. With the two process connection threads ½" and " flush at the front, the SITRANS P00 and DS III transmitters can be used for all processes in the paper industry. SITRANS P00 and SITRANS PDS III series pressure transmitters are digital pressure transmitters featuring etensive userfriendliness and high accuracy. The parameterization is performed using control keys via HART, PROFIBUS-PA or FOUNDATION Fieldbus interface. Etensive functionality enables the pressure transmitter to be precisely adapted to the plant s requirements. Operation is very simple in spite of the numerous setting options. Transmitters with type of protection "Intrinsic safety" and "Eplosion-proof" may be installed within potentially eplosive atmospheres (zone ) or in zone 0. The transmitters are provided with an EC type eamination certificate and comply with the corresponding harmonized European standards (ATEX). Various versions of the pressure transmitters are available for measuring: Gauge pressure Level Mass level Volume level Application The pressure transmitters of the DS III series, can be used in industrial areas with etreme chemical and mechanical loads. Electromagnetic compatibility in the range 0 khz to GHz makes the DS III pressure transmitters suitable for locations with high electromagnetic emissions. Pressure transmitters with type of protection "Intrinsic safety" and "Eplosion-proof" may be installed within potentially eplosive atmospheres (zone ) or in zone 0. The pressure transmitters are provided with an EC type eamination certificate and comply with the corresponding harmonized European standards (ATEX). Pressure transmitters with the type of protection "Intrinsic safety" for use in zone 0 may be operated with power supply units of category "ia" and "ib". The transmitters can be equipped with various designs of remote seals for special applications such as the measurement of highly viscous substances. The pressure transmitter can be operated locally over control keys or programmed eternally over HART or over PROFIBUS-PA or FOUNDATION Fieldbus interface (only DS III). SITRANS P, DS III series Measured variable: Gauge pressure of aggressive and non-aggressive gases, vapors and liquids. Span (infinitely adjustable) For DS III with HART: bar ( psi) Nominal measuring range For DS III with PROFIBUS PA or FOUNDATION Fieldbus:... bar ( psi) SITRANS P00 Span (infinitely adjustable) For DS III with HART: bar ( psi) Nominal measuring range For DS III with PROFIBUS PA or FOUNDATION Fieldbus:... bar ( psi) /72 Siemens FI US Edition

2 Siemens AG 207 Design SITRANS P DS III SITRANS P DS III and P00 with PMC connection - Technical description Eample for an attached measuring point label Y0 or Y02 = ma. 27 char. Y5 = ma. char. Y99 = ma. 0 char. Y = ma. 27 char.... to... mbar Measuring point number (TAG No.) 24 Measuring point tet 8 2 SITRANS P00 The device comprises: Electronics Housing Measuring cell Plastic cover as access to the input keys 2 Screw cover with viewing pane Digital display 4 Locking screw 5 Process connection Screw cover with viewing pane 7 Rating plate 8 Inlet with cable gland Device front view, SITRANS P DS III The transmitter consists of various components depending on the order. The possible versions are listed in the ordering information. The components described below are the same for all transmitters. The rating plate (7, Figure "Device front view) with the Article No. is located on the side of the housing. The specified number together with the ordering information provide details on the optional design details and on the possible measuring range (physical properties of built-in sensor element). The approval label is located on the opposite side. The housing is made of die-cast aluminium or stainless steel precision casting. A round cover is screwed on at the front and rear of the housing. The front cover (2) can be fitted with a viewing pane so that the measured values can be read directly on the display. The inlet (8) for the electrical connection is located either on the left or right side. The unused opening on the opposite side is sealed by a blanking plug. The protective earth connection is located on the rear of the housing. The electrical connections for the power supply and screen are accessible by unscrewing the rear cover. The bottom part of the housing contains the measuring cell with process connection (5). The measuring cell is prevented from rotating by a locking screw (4). As the result of this modular design, the measuring cell and the electronics can be replaced separately from each other. The set parameter data are retained. At the top of the housing is a plastic cover (), which hides the input keys. 5 Digital display 2 Process connection Cable gland 4 Rating plate 5 Screw-on lid 4 Perspective view of the SITRANS P00 The housing has a screw-on lid (5) and, depending on the version, is with or without an inspection window. The electrical terminal housing, the buttons for operation of the device are located under this lid and, depending on the version, the display. The connections for the auiliary power UH and the shield are in the terminal housing. The cable gland is on the side of the housing. The measuring cell with the process connection (2) is located on the bottom of the housing. The measuring cell with the process connection may differ from the one shown in the diagram, depending on the device version. 2 Siemens FI US Edition /7

3 Siemens AG 207 SITRANS P DS III and P00 with PMC connection - Technical description Function Operation of electronics with HART communication 2 Sensor p e 8 M EEPROM Measuring cell 4 μc HART interface Electronics Measuring cell sensor 2 Instrument amplifier Analog-to-digital converter 4 Microcontroller 5 Digital-to-analog converter One non-volatile memory each in the measuring cell and electronics 7 HART interface 8 Three input keys (local operation) 9 Digital display 0 Diode circuit and connection for eternal ammeter I A Output current U H Power supply P e Input variable 5 EEPROM Function diagram of electronics The bridge output voltage created by the sensor (, Figure "Function diagram of electronics") is amplified by the measuring amplifier (2) and digitized in the analog-to-digital converter (). The digital information is evaluated in a microcontroller, its linearity and temperature response corrected, and converted in a digital-to-analog converter (5) into an output current of 4 to 20 ma. The diode circuit (0) protects against incorrect polarity. The data specific to the measuring cell, the electronics data, and the parameter data are stored in the two non-volatile memories (). The one memory is coupled to the measuring cell, the other to the electronics. As the result of this modular design, the electronics and the measuring cell can be replaced separately from each other. Using the input keys (8) you can parameterize the pressure transmitter directly at the measuring point. The input buttons can also be used to control the view of the results, the error messages and the operating modes on the display (9). The HART modem (7) permits parameterization using a protocol according to the HART specification. The pressure transmitters with spans bar (94 psi) measure the input pressure compared to atmosphere, the transmitters with spans 0 bar (220 psi) measure compared to vacuum. 0 I A, U H Operation of electronics with PROFIBUS PA communication PA μc interface Sensor p e 8 M EEPROM Measuring cell EEPROM Measuring cell sensor 2 Instrument amplifier Analog-to-digital converter 4 Microcontroller 5 Electrical isolation One non-volatile memory each in the measuring cell and electronics 7 PROFIBUS-PA interface Electronics Power supply 0 Power supply unit Coupler Function diagram of electronics The bridge output voltage created by the sensor (, Figure "Function diagram of electronics") is amplified by the measuring amplifier(2) and digitized in the analog-to-digital converter (). The digital information is evaluated in the microcontroller, its linearity and temperature response corrected, and provided on the PROFIBUS PA through an electrically isolated PA interface (7). The data specific to the measuring cell, the electronics data, and the parameter data are stored in the two non-volatile memories (). The first memory is linked with the measuring cell, the second with the electronics. This modular design means that the electronics and the measuring cell can be replaced separately from one another. Using the three input buttons (8) you can parameterize the pressure transmitter directly at the measuring point. The input buttons can also be used to control the view of the results, the error messages and the operating modes on the display (9). The results with status values and diagnostic values are transferred by cyclic data transmission on the PROFIBUS PA. Parameterization data and error messages are transferred by acyclic data transmission. Special software such as SIMATIC PDM is required for this. PROFIBUS DP Bus- Master 8 Three input keys (local operation) 9 Digital display 0 Power supply DP/PA coupler or link 2 Bus master p e PROFIBUS-PA 2 Input variable /74 Siemens FI US Edition

4 Siemens AG 207 Operation of electronics with FOUNDATION Fieldbus communication SITRANS P DS III and P00 with PMC connection - Technical description Mode of operation of the measuring cell Measuring cell for gauge pressure with front-flush diaphragm 8 M FF μc interface EEPROM Electronics Foundation Fieldbus Power supply 0 Power supply unit Coupler 5 4 p e 2 Measuring cell 2 Process connection Seal diaphragm 4 Filling liquid 5 Silicon pressure sensor Pressure as input variable p e Sensor p e EEPROM Measuring cell Measuring cell sensor 2 Instrument amplifier Analog-to-digital converter 4 Microcontroller 5 Electrical isolation One non-volatile memory each in the measuring cell and electronics 7 FF interface 8 Three input keys (local operation) 9 Digital display 0 Power supply Function diagram of electronics The bridge output voltage created by the sensor (, Figure "Function diagram of electronics") is amplified by the measuring amplifier (2) and digitized in the analog-to-digital converter (). The digital information is evaluated in the microcontroller, its linearity and temperature response corrected, and provided on the FOUNDATION Fieldbus through an electrically isolated FOUNDATION Fieldbus interface (7). The data specific to the measuring cell, the electronics data, and the parameter data are stored in the two non-volatile memories (). The one memory is coupled to the measuring cell, the other to the electronics. As the result of this modular design, the electronics and the measuring cell can be replaced separately from each other. Using the three input buttons (8) you can parameterize the pressure transmitter directly at the measuring point. The input buttons can also be used to control the view of the results, the error messages and the operating modes on the display (9). The results with status values and diagnostic values are transferred by cyclic data transmission on the FOUNDATION Fieldbus. Parameterization data and error messages are transferred by acyclic data transmission. Special software such as National Instruments Configurator is required for this. p e Input variable Measuring cell for gauge pressure, with front-flush diaphragm for paper industry, function diagram The pressure p e is applied through the process connection (2, Figure "Measuring cell for gauge pressure, with front-flush diaphragm for paper industry, function diagram) to the measuring cell (). This pressure is subsequently transmitted further through the seal diaphragm () and the filling liquid (4) to the silicon pressure sensor (5) whose measuring diaphragm is then fleed. This changes the resistance of the four piezo-resistors fitted in the diaphragm in a bridge circuit. This change in resistance results in a bridge output voltage proportional to the absolute pressure. Parameterization Depending on the version, there are a range of options for parameterizing the pressure transmitter and for setting or scanning the parameters. Parameterization using the input buttons (local operation) With the input buttons you can easily set the most important parameters without any additional equipment. Parameterization using HART Parameterization using HART is performed with a HART Communicator or a PC. SITRANS P transmitter Power supply Communication between a HART Communicator and a pressure transmitter When parameterizing with the HART Communicator, the connection is made directly to the 2-wire cable. SITRANS P transmitter HART communicator HART modem Ω Ω PC or laptop Power supply USB/RS 22 HART communication between a PC communicator and a pressure transmitter Siemens FI US Edition /75

5 Siemens AG 207 SITRANS P DS III and P00 with PMC connection - Technical description When parameterizing with a PC, the connection is made through Parameterization through PROFIBUS PA interface a HART modem. The signals needed for communication in conformity with the HART 5. or. protocols are superimposed on the output current using the Frequency Shift Keying (FSK) method. Adjustable parameter DS III with HART and P00 with HART Parameters Input keys HART communication Start of scale Full-scale value Electrical damping Start-of-scale value without application of a pressure ("Blind setting") Full-scale value without application of a pressure ("Blind setting") Zero adjustment current transmitter Fault current Disabling of buttons, write protection ) Type of dimension and actual dimension Characteristic (linear) Input of characteristic Freely-programmable LCD Diagnostic functions ) Cancel apart from write protection Diagnostic functions for DS III with HART and P00 with HART Zero correction display Event counter Limit transmitter Saturation alarm Slave pointer Simulation functions Maintenance timer Available physical units of display for DS III with HART and P00 with HART Physical variable Physical dimensions Pressure (setting can also be Pa, MPa, kpa, bar, mbar, torr, atm, made in the factory) psi, g/cm 2, kg/cm 2, inh 2 O, inh 2 O (4 C), mmh 2 O, fth 2 O (20 C), inhg, mmhg Level (height data) m, cm, mm, ft, in Volume m, dm, hl, yd, ft, in, US gallon, lmp. gallon, bushel, barrel, barrel liquid Mass g, kg, t, lb, Ston, Lton, oz Temperature K, C, F, R Miscellaneous %, ma Fully digital communication through PROFIBUS PA, profile.0, is particularly user-friendly. The PROFIBUS connects the DS III PA to a process control system, e.g. SIMATIC PSC 7. Communication is possible even in a potentially eplosive environment. For parameterization through PROFIBUS you need suitable software, e.g. SIMATIC PDM (Process Device Manager). Parameterization through FOUNDATION Fieldbus interface Fully digital communication through FOUNDATION Fieldbus is particularly user-friendly. Through the FOUNDATION Fieldbus the DS III with FOUNDATION Fieldbus is connected to a process control system. Communication is possible even in a potentially eplosive environment. For parameterization through the FOUNDATION Fieldbus you need suitable software, e.g. National Instruments Configurator. Adjustable parameters for DS III with PROFIBUS PA and FOUNDATION Fieldbus, and P00 with PROFIBUS PA and FOUNDATION Fieldbus Adjustable parameters Input keys PROFIBUS PA and FOUNDA- TION Fieldbus interface Electrical damping Zero adjustment (correction of position) Buttons and/or function disabling Source of measured-value display Physical dimension of display Position of decimal point Bus address Adjustment of characteristic Input of characteristic Freely-programmable LCD Diagnostic functions Diagnostic functions for DS III with PROFIBUS PA and FOUNDATION Fieldbus, and P00 with PROFIBUS PA and FOUNDATION Fieldbus Event counter Slave pointer Maintenance timer Simulation functions Display of zero correction Limit transmitter Saturation alarm Physical dimensions available for the display Physical variable Physical dimensions Pressure (setting can also be MPa, hpa, kpa, Pa, bar, mbar, torr, made in the factory) atm, psi, g/cm 2, kg/cm 2, mmh 2 O, mmh 2 O (4 C), inh 2 O, inh 2 0 ( 4 C), fth 2 O, mmhg, inhg Level (height data) m, cm, mm, ft, in, yd Mass g, kg, t, lb, Ston, Lton, oz Volume m, dm, hl, yd, ft, in, US gallon, lmp. gallon, bushel, barrel, barrel liquid Temperature K, C, F, R Miscellaneous % /7 Siemens FI US Edition

6 Siemens AG 207 Technical specifications SITRANS P, DS III series for gauge pressure with PMC connection for the paper industry Input Measured variable Gauge pressure Span (fully adjustable) or measuring range, ma. operating pressure and ma. test pressure HART PROFIBUS PA/ FOUNDATION Fieldbus Span Nominal measuring range bar kpa psi bar kpa psi bar kpa psi bar 00 kpa 4.5 psi 4bar 400 kpa 58 psi bar 00 kpa 22 psi SITRANS P DS III with PMC connection Ma. operating pressure MAWP (PS) 4bar 400 kpa 58 psi 7bar 0.7 MPa 02 psi 2 bar 2. MPa 05 psi Ma. perm. test pressure bar 00 kpa 87 psi 0 bar MPa 45 psi 2 bar.2 MPa 44 psi Lower measuring limit 00 mbar a/0 kpa a/.45 psia (For PMC-Style Minibolt no span < 500 mbar adjustable) Upper measuring limit 00% of ma. span Output HART PROFIBUS PA/ FOUNDATION Fieldbus Output signal ma Digital PROFIBUS PA and FOUNDATION Fieldbus signal Lower limit (infinitely adjustable).55 ma, factory preset to.84 ma - Upper limit (infinitely adjustable) 2 ma, factory preset to 20.5 ma or - optionally set to 22.0 ma Load Without HART communication R B (U H V)/0.02 A in Ω, - U H : Power supply in V With HART communication R B = Ω (SIMATIC PDM) or - R B = Ω (HART-Communicator) Physical bus - IEC 58-2 Protection against polarity reversal Protected against short-circuit and polarity reversal. Each connection against the other with ma. supply voltage. Electrical damping (step width 0. s) Set to 2 s ( s) Measuring accuracy Acc. to IEC Reference conditions (All error data refer always refer to the set span) Increasing characteristic Start-of-scale value 0 bar/kpa/psi Stainless steel seal diaphragm Silicone oil filling Room temperature 25 C (77 F) Measuring span ratio r (spread, Turn-Down) r = ma. measuring span/set measuring span or nom. pressure range Error in measurement at limit setting incl. hysteresis and reproducibility Linear characteristic -r % - 5<r 00 (0.005 r ) % Influence of ambient temperature (in percent per 28 C (50 F)) (0.08 r + 0.) % Long-term stability (temperature change ± 0 C (± 54 F)) (0.25 r) % in 5 years Effect of mounting position 0. mbar/0.0 kpa/ psi per 0 inclination (zero point correction is possible with position error compensation) Effect of auiliary power supply % per V (in percent per change in voltage) Measuring value resolution for PROFIBUS PA and 0-5 of nominal measuring range FOUNDATION Fieldbus Siemens FI US Edition /77

7 Siemens AG 207 SITRANS P DS III with PMC connection SITRANS P, DS III series for gauge pressure with PMC connection for the paper industry HART PROFIBUS PA and FOUNDATION Fieldbus Rated conditions Degree of protection to IEC 0529 IP (optional IP/IP8), NEMA 4X Temperature of medium C ( F) Ambient conditions Ambient temperature C ( F) - Transmitter C ( F) Storage temperature C ( F) Climatic class - Condensation Relative humidity % Condensation permissible, suitable for use in the tropics Electromagnetic Compatibility - Emitted interference and interference immunity Acc. to IEC 2 and NAMUR NE 2 Design Weight (without options).5 kg (. lb) Enclosure material Low-copper die-cast aluminum, GD-AlSi2 or stainless steel precision casting, mat. no Wetted parts materials Gasket (standard) PTFE flat gasket O-ring (minibolt) FPM (Viton) or optionally: FFPM or NBR Measuring cell filling Silicone oil or inert filling liquid Process connection (standard) Flush-mounted, ½", PMC Standard design Process connection (minibolt) Flush-mounted, ", minibolt design Power supply U H Terminal voltage on transmitter V DC V DC in intrinsically-safe mode Power supply - Supplied through bus Separate 24 V power supply - Not necessary Bus voltage Not E V With intrinsically-safe operation V Current consumption Basic current (ma.) ma Start-up current basic current - Yes Ma. current in event of fault ma Fault disconnection electronics (FDE) available - Yes Certificates and approvals Classification according to PED 204/8/EU For gases of fluid group and liquids of fluid group ; complies with requirements of article 4, paragraph (sound engineering practice) /78 Siemens FI US Edition

8 Siemens AG 207. HART communication HART communication Ω Protocol HART Version 5. Software for computer PROFIBUS PA communication Simultaneous communication with master class 2 (ma.) The address can be set using Cyclic data usage Output byte Input byte Internal preprocessing Device profile Function blocks 2 Analog input - Adaptation to customer-specific process variables SIMATIC PDM 4 Configuration tool or local operation (standard setting address 2) 5 (one measured value) or 0 (two measured values) 0,, or 2 (register operating mode and reset function for metering) PROFIBUS PA Profile for Process Control Devices Version.0, class B Yes, linearly rising or falling characteristic - Electrical damping, adjustable s - Simulation function Input /Output - Failure mode parameterizable (last good value, substitute value, incorrect value) - Limit monitoring Yes, one upper and lower warning limit and one alarm limit respectively Register (totalizer) Can be reset, preset, optional direction of counting, simulation function of register output - Failure mode parameterizable (summation with last good value, continuous summation, summation with incorrect value) - Limit monitoring One upper and lower warning limit and one alarm limit respectively Physical block Transducer blocks 2 Pressure transducer block - Can be calibrated by applying Yes two pressures - Monitoring of sensor limits Yes - Specification of a container Ma. 0 nodes characteristic with - Square-rooted characteristic Yes for flow measurement - Gradual volume suppression Parameterizable and implementation point of square-root etraction - Simulation function for measured pressure value and sensor temperature Constant value or over parameterizable ramp function FOUNDATION Fieldbus communication Function blocks SITRANS P DS III with PMC connection function blocks analog input, function block PID Analog input - Adaptation to customer-specific process variables characteristic Yes, linearly rising or falling - Electrical damping, adjustable s - Simulation function Output/input (can be locked within the device with a bridge) - Failure mode parameterizable (last good value, substitute value, incorrect value) - Limit monitoring Yes, one upper and lower warning limit and one alarm limit respectively - Square-rooted characteristic Yes for flow measurement PID Standard FOUNDATION Fieldbus function block Physical block resource block Transducer blocks transducer block Pressure with calibration, transducer block LCD Pressure transducer block - Can be calibrated by applying Yes two pressures - Monitoring of sensor limits Yes - Simulation function: Measured pressure value, sensor temperature and electronics temperature Constant value or over parameterizable ramp function Siemens FI US Edition /79

9 Siemens AG 207 SITRANS P DS III with PMC connection Selection and Ordering data Article No. SITRANS P pressure transmitters for gauge pressure, with PMC connection series DS III with HART 7 M F Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Measuring cell filling Measuring cellcleaning Silicone oil normal Inert liquid grease-free to cleanliness level 2 Measuring span (min.... ma.) bar ) ( psi) ) B bar ( psi) C bar ( psi) D Wetted parts materials Seal diaphragm Connection shank Hastelloy Stainless steel B Process connection PMC Style Standard: Thread ½" 2 PMC Style Minibolt: front-flush " (not with minimum span: 500 mbar (7.25 psi) - version "B") Non-wetted parts materials Housing made of die-cast aluminium 0 Housing stainless steel precision casting Version Standard version, German plate inscription, setting for pressure unit: bar International version, English plate inscription, 2 setting for pressure unit: bar Chinese version, English plate inscription, setting for pressure unit: Pascal All versions include DVD with compact operating instructions in various EU languages. Eplosion protection None A With ATEX, Type of protection: - "Intrinsic safety (E ia)" B - "Eplosion-proof (E d)" 2) D - E na/ic (Zone 2)" ) E FM + CSA intrinsic safe (is) 4) F With FM + CSA, Type of protection: - "Intrinsic Safe and Eplosion Proof (is + p)" )4) N C Electrical connection / cable entry Female thread M20.5 B Female thread ½-4 NPT C M2 connectors (stainless steel) 5) ) F Display Without display 0 Without visible display (display concealed, setting: ma) With visible display (setting: ma) With customer-specific display (setting as specified, 7 Order code "Y2" required) Power supply units see Chap. 7 "Supplementary Components". Included in delivery of the device: Quick-start guide Sealing ring ) Only with "PMC Style Standard" process connection 2) Without cable gland, with blanking plug ) Configurations with M2 connectors are only available in E ic. 4) Eplosion protection acc. to FM/CSA: suitable for installations according to NEC 500/505. 5) Only in connection with E approval A, B, E or F. ) M2 delivered without cable socket Selection and Ordering data Article No. SITRANS P pressure transmitter for gauge pressure, with PMC connection DS III with PROFIBUS PA (PA) 7 M F DS III with FOUNDATION Fieldbus (FF) 7 M F Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Measuring cell filling Meas. cell cleaning Silicone oil normal Inert liquid grease-free to cleanliness level 2 Nominal measuring range bar ) (4.5 psi) ) B 4 bar (58 psi) C bar (22 psi) D Wetted parts materials Seal diaphragm Connection shank Hastelloy Stainless steel B Process connection 2) PMC Style Standard: Thread ½" 2 PMC Style Minibolt: front-flush " (minimum span: 500 mbar (7.25 psi), not available with -bar-measuring cell (Option B)) Non-wetted parts materials Housing made of die-cast aluminium 0 Housing stainless steel precision casting Version Standard version, German plate inscription, setting for pressure unit: bar International version, English plate inscription, 2 setting for pressure unit: bar Chinese version, English plate inscription, setting for pressure unit: Pascal All versions include DVD with compact operating instructions in various EU languages. Eplosion protection None A With ATEX, Type of protection: - "Intrinsic safety (E ia)" B - "Eplosion-proof (E d)" ) D - E na/ic (Zone 2)" 4) E FM + CSA intrinsic safe (is) 5) F With FM + CSA, Type of protection: - "Intrinsic Safe and Eplosion Proof (is + p)" )5) N C Electrical connection / cable entry Female thread M20.5 B Female thread ½-4 NPT C M2 connectors (stainless steel) ) 7) F Display Without display 0 Without visible display (display concealed, setting: bar) With visible display (setting: bar) With customer-specific display (setting as specified, 7 Order code "Y2" required) Included in delivery of the device: Quick-start guide Sealing ring ) Only with "PMC Style Standard"process connection 2) Sealing is included in delivery. ) Without cable gland, with blanking plug 4) Configurations with M2 connectors are only available in E ic. 5) Eplosion protection acc. to FM/CSA: suitable for installations according to NEC 500/505 ) Only in connection with E approval A, B, E or F. 7) M2 delivered without cable socket /80 Siemens FI US Edition

10 Siemens AG 207 Selection and Ordering data Order code Further designs HART PA FF Add "-Z" to Article No. and specify Order code. Plug Angled A2 Han 8D (metal, gray) A M2 cable sockets (metal (CuZn)) A50 Rating plate inscription (instead of German) English B French B2 Spanish B Italian B4 Cyrillic (russian) B English rating plate B2 Pressure units in inh 2 0 and/or psi Quality Inspection Certificate (5-point characteristic C curve test) according to IEC Inspection certificate C2 Acc. to EN Factory certificate C4 Acc. to EN "Functional safety (SIL2)" certificate acc. to IEC 508 C20 "Functional safety (SIL2/)" certificate acc. C2 to IEC 508 PED for Russia with initial calibration mark C99 Setting of the upper saturation limit of the D05 output signal to 22.0 ma Degree of protection IP/IP8 D2 (only for M20.5 and ½-4 NPT) Eport approval Korea E Eplosion-proof "Intrinsic safety" to NEPSI (China) E55 ) (only for transmitter 7MF B..) Eplosion protection "Eplosion-proof" E5 ) to NEPSI (China) (only for transmitter 7MF D..) E protection "Zone 2" to NEPSI (China) E57 ) (only for transmitter 7MF E..) E protection E ia", E d" and Zone 2" E58 ) to NEPSI (China) (only for transmitter 7MF R..) Mounting Weldable sockets for standard ½" P0 threaded connection Weldable socket for minibolt connection " P02 (incl. screw 5/-8 UNC-2B and washer) ) Option does not include ATEX approval, but instead includes only the country-specific approval. SITRANS P DS III with PMC connection Selection and Ordering data Order code Additional data HART PA FF Please add "-Z" to Article No. and specify Order code(s) and plain tet. Measuring range to be set Y0 ) Specify in plain tet (ma. 5 characters): Y0:... up to... mbar, bar, kpa, MPa, psi Stainless steel tag plate and entry in Y5 device variable (measuring point description) Ma. characters, specify in plain tet: Y5:... Measuring point tet (entry in device variable) Y Ma. 27 characters, specify in plain tet: Y:... Entry of HART address (TAG) Y7 Ma. 8 characters, specify in plain tet: Y7:... Setting of pressure indication in pressure Y2 units Specify in plain tet (standard setting: bar): Y2: mbar, bar, kpa, MPa, psi,... Note: The following pressure units can be selected: bar, mbar, mm H 2 O *), inh 2 O *), fth 2 O *), mmhg, inhg, psi, Pa, kpa, MPa, g/cm 2, kg/cm 2, Torr, ATM or % *) ref. temperature 20 C Setting of pressure indication in nonpressure Y22 + units 2) Y0 Specify in plain tet: Y22:... up to... l, m, m, USg,... (specification of measuring range in pressure units "Y0" is essential, unit with ma. 5 characters) Preset bus address Y25 possible between and 2 Ma. 8 characters, specify in plain tet: Y25:... Only "Y0" and "Y2" can be factory preset = available ordering eample Item line: 7MF4-DB20-AB7-Z B line: C + Y0 + Y2 C line: Y0:... 0 bar ( psi) C line: Y2: bar (psi) ) Measuring accuracies for PROFIBUS PA transmitters with Option Y0 are calculated in the same way as for HART devices. 2) Preset values can only be changed over SIMATIC PDM. Siemens FI US Edition /8

11 Siemens AG 207 SITRANS P DS III with PMC connection Dimensional drawings 5 4 (5.) (0.) 74 (2.9) 5 (2.) 24 (0.94) 29 (.4) 84 (.) 4 Ø80 (.5) 50 (.97) 2 min. 90 (.54) 2) 5 0 (5.2) H = appro. 7 Space for rotation of housing H 2 2 Electronic side, digital display (longer overall length for cover with window) ) Terminal side ) Electrical connection: Screwed gland M20,5 or screwed gland ½-4 NPT or M2 conector Protective cover over keys Blanking plug Screw cover - safety bracket (only for type of protection "Eplosion-proof enclosure", not shown in the drawing) Process connection: PMC standard ) Allow appro. 20 mm (0.79 inch) thread length to permit unscrewing 2) 92 mm (. inch) for minimum distance to permit rotation with indicator SITRANS P DS III pressure transmitters for gauge pressure, with PMC connection, dimensions in mm (inch) The diagram shows a SITRANS P DS III with an eample of a PMC Style standard flange. In this drawing the height is subdivided into H and H 2. H = Height of the SITRANS P DS III up to a defined cross-section H 2 = Height of the flange up to this defined cross-section Only the height H 2 is indicated in the dimensions of the flanges. M44,25 Ø,4 (.) Ø 2,7 (.05) H 2 D DN PN D H mm (.") appro..8 mm (.4") 20,9 (0.82) Ø, (.44) Ø 58,9 (2.2) ) Ø 8 (0.) 25,4 () 7,8 (0.7) PMC Style minibolt H 2 DN PN D H 2 2. mm (.0") appro.. mm (.") D ) O-ring surface (bore hole Ø 8 mm (0. ) without burr) PMC Style Standard (left) and PMC Style Minibolt (right) weldable sockets, dimensions in mm (inch) Material: Stainless steel, Mat. No..4404/L /82 Siemens FI US Edition

12 Siemens AG 207 Technical specifications SITRANS P00 for gauge pressure with PMC connection for the paper industry Input Measured variable Gauge pressure (front-flush) Span (fully adjustable) or measuring range, ma. operating pressure and ma. test pressure HART PROFIBUS PA/ FOUNDATION Fieldbus Span Nominal measuring range bar kpa psi bar kpa psi bar kpa psi bar 00 kpa 4.5 psi 4bar 400 kpa 58 psi bar 00 kpa 22 psi SITRANS P00 with PMC connection Ma. operating pressure MAWP (PS) 4bar 400 kpa 58 psi 7bar 0.7 MPa 02 psi 2 bar 2. MPa 05 psi Ma. perm. test pressure bar 00 kpa 87 psi 0 bar MPa 45 psi 2 bar.2 MPa 44 psi Lower measuring limit 00 mbar a/0 kpa a/.45 psia (For PMC-Style Minibolt no span < 500 mbar adjustable) Upper measuring limit 00 % of ma. span Output HART PROFIBUS PA/ FOUNDATION Fieldbus Output signal ma Digital PROFIBUS PA and FOUNDATION Fieldbus signal Lower limit (infinitely adjustable).55 ma, factory preset to.84 ma - Upper limit (infinitely adjustable) 2 ma, factory preset to 20.5 ma or - optionally set to 22.0 ma Load Without HART communication R B (U H V)/0.02 A in Ω, - U H : Power supply in V With HART communication R B = Ω (SIMATIC PDM) or - R B = Ω (HART Communicator) Physical bus - IEC 58-2 Protection against polarity reversal Protected against short-circuit and polarity reversal. Each connection against the other with ma. supply voltage. Electrical damping (step width 0. s) Set to 2 s ( s) Measuring accuracy Acc. to IEC Reference conditions Increasing characteristic Start-of-scale value 0 bar/kpa/psi Stainless steel seal diaphragm Measuring cell with silicone oil Room temperature 25 C (77 F) Measuring span ratio r (spread, Turn-Down) r = ma. measuring span/set measuring span or nom. pressure range Error in measurement at limit setting incl. hysteresis and reproducibility Linear characteristic -r % - 5<r 00 (0.005 r ) % Influence of ambient temperature (0.08 r + 0.) % (in percent per 28 C (50 F)) Long-term stability (temperature change ± 0 C (± 54 F)) (0.25 r) % in 5 years Effect of mounting position 0. mbar/0.0 kpa/ psi per 0 inclination (zero point correction is possible with position error compensation) Effect of auiliary power supply % per V (in percent per change in voltage) Measuring value resolution for PROFIBUS PA and 0-5 of nominal measuring range FOUNDATION Fieldbus Siemens FI US Edition /8

13 Siemens AG 207 SITRANS P00 with PMC connection SITRANS P00 for gauge pressure with PMC connection for the paper industry Rated conditions Installation conditions Ambient temperature Observe the temperature class in areas subject to eplosion hazard. Measuring cell with silicone oil C ( F) Display readable C ( F) Storage temperature C ( F) Climatic class Condensation Relative humidity % Condensation permissible, suitable for use in the tropics Degree of protection acc. to EN 0529 IP5, IP8, NEMA 4X, enclosure cleaning, resistant to lyes, steam to 50 C (02 F) Electromagnetic Compatibility Emitted interference and interference immunity Acc. to IEC 2 and NAMUR NE 2 Medium conditions Temperature of medium Measuring cell with silicone oil C ( F) Design Weight (without options) Appro. kg (2.2 lb) Enclosure material Stainless steel, mat. no..40/04 Material of parts in contact with the medium Seal diaphragm Hastelloy C27, mat. no Measuring cell filling Silicone oil Surface quality touched-by-media Ra-values 0.8 µm (2 µ inch)/welds Ra. µm (4 µ inch) Power supply U H HART PROFIBUS PA/ FOUNDATION Fieldbus Terminal voltage on transmitter V DC for intrinsically safe operation: V DC Power supply Supplied through bus Separate power supply - Not necessary Bus voltage Without E V With intrinsically-safe operation V Current consumption Ma. basic current ma Start-up current basic current - Yes Ma. fault current in the event of a fault ma Fault disconnection electronics (FDE) available - Yes /84 Siemens FI US Edition

14 Siemens AG 207 SITRANS P00 with PMC connection SITRANS P00 for gauge pressure with PMC connection for the paper industry Certificates and approvals HART PROFIBUS PA/ FOUNDATION Fieldbus Classification according to PED 204/8/EU For gases of fluid group and liquids of fluid group ; complies with requirements of Article 4, paragraph (sound engineering practice) Eplosion protection Intrinsic safety "i" PTB 05 ATEX 2048 Marking II /2 G E ia llc/llb T4/T5/T Ga/Gb Permissible ambient temperature Temperature class T C ( F) Temperature class T C ( F) Temperature class T C ( F) Connection To certified intrinsically-safe circuits with peak values: U i = 0 V, I i = 00 ma, P i = 750 mw, R i = 00 Ω To certified intrinsically-safe circuits with peak values: FISCO supply unit: U i = 7.5 V, I i = 80 ma, P i = 5.2 W Linear barrier: U i = 24 V, I i = 250 ma, P i =.2 W Effective inner capacitance: C i = nf C i =. nf Effective internal inductance: L i = 0.4 mh L i 7 μh Eplosion protection to FM for USA and Canada (cfm US ) Identification (DIP) or (IS); (NI) Certificate of Compliance CL I, DIV, GP ABCD T4... T; CL II, DIV, GP EFG; CL III; CL I, ZN 0/ AE ia IIC T4... T; CL I, DIV 2, GP ABCD T4... T; CL II, DIV 2, GP FG; CL III Identification (DIP) or (IS) Certificate of Compliance C CL I, DIV, GP ABCD T4... T; CL II, DIV, GP EFG; CL III; E ia IIC 4... T; CL I, DIV 2, GP ABCD T4... T; CL II, DIV 2, GP FG; CL III Siemens FI US Edition /85

15 Siemens AG 207 SITRANS P00 with PMC connection HART communication HART Ω Protocol HART Version 5. Software for computer SIMATIC PDM PROFIBUS PA communication Simultaneous communication with 4 master class 2 (ma.) The address can be set using Configuration tool Local operation (standard setting Address 2) Cyclic data usage Output byte One measured value: 5 bytes Two measured values: 0 bytes Input byte Register operating mode: bytes Reset function due to metering. bytes Device profile PROFIBUS PA Profile for Process Control Devices Version.0, class B Function blocks 2 Analog input - Adaptation to customer-specific process variables Linearly rising or falling characteristic - Electrical damping s adjustable - Simulation function Input /Output - Limit monitoring One upper and lower warning limit and one alarm limit respectively Register (totalizer) Can be reset and preset Optional direction of counting Simulation function of the register output - Limit monitoring One upper and lower warning limit and one alarm limit respectively Physical block Transducer blocks 2 Pressure transducer block - Monitoring of sensor limits Yes - Specification of a container Ma. nodes characteristic with - Characteristic curve Linear - Simulation function Available Transducer block "Electronic temperature" Simulation function Available FOUNDATION Fieldbus communication Function blocks function blocks analog input, function block PID Analog input - Adaptation to customerspecific process variables characteristic Yes, linearly rising or falling - Electrical damping, adjustable s - Simulation function Output/input (can be locked within the device with a bridge) - Failure mode parameterizable (last good value, substitute value, incorrect value) - Limit monitoring Yes, one upper and lower warning limit and one alarm limit respectively - Square-rooted characteristic Yes for flow measurement PID Standard FOUNDATION Fieldbus function block Physical block resource block Transducer blocks transducer block Pressure with calibration, transducer block LCD Pressure transducer block - Can be calibrated by applying Yes two pressures - Monitoring of sensor limits Yes - Simulation function: Measured pressure value, sensor temperature and electronics temperature Constant value or over parameterizable ramp function /8 Siemens FI US Edition

16 Siemens AG 207 Selection and Ordering data SITRANS P00 pressure transmitters with PMC connection, single-chamber measuring housing, rating plate inscription in English Article No. with ma / HART 7 M F with PROFIBUS PA 7 M F with FOUNDATION Fieldbus (FF) 7 M F Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Measuring cell filling Measuring cell cleaning Silicone oil normal Inert liquid Cleanliness level 2 to DIN 2540 Measuring span bar ) (4.5 psi) B 4 bar (58 psi) C bar (22 psi) D Wetted parts materials Seal diaphragm Measuring cell Hastelloy Stainless steel B Process connection PMC Style Standard: Thread ½" 2 PMC Style Minibolt: front-flush " (minimum span: 500 mbar (7.25 psi), not available with -bar-measuring cell (Option B)) Non-wetted parts materials Stainless steel, deep-drawn and electrolytically 4 polished Version Standard versions Eplosion protection None A With ATEX, Type of protection: - "Intrinsic safety (E ia)" B Zone 20/2/22 2) C E na/nl (Zone 2) ) E With FM + CSA, Type of protection: - "Intrinsic Safe (is)" (planned) 4) M Electrical connection/cable entry Screwed gland M20.5 (polyamide) 5) A Screwed gland M20.5 (metal) B Screwed gland M20.5 (stainless steel) C M2 connectors (without cable socket) F M2 connectors (stainless steel), without cable G socket) ½-4 NPT metal thread ) H ½-4 NPT stainless steel thread ) J SITRANS P00 with PMC connection Selection and Ordering data Article No. SITRANS P00 pressure transmitters with PMC connection, single-chamber measuring housing, rating plate inscription in English with ma / HART 7 M F with PROFIBUS PA 7 M F with FOUNDATION Fieldbus (FF) 7 M F Display Without display, with keys, closed lid With display and keys, closed lid 7) 2 With display and keys, lid with Makrolon pane 4 (setting on HART devices: ma, with PROFIBUS PA and FOUNDATION Fieldbus equipment: pressure units) 7) With display and keys (setting acc. to specifications, Order code "Y2" or "Y22" required), lid with 5 Makrolon pane 7) With display and keys, lid with glass pane (setting on HART devices: ma, with PROFIBUS PA and FOUNDATION Fieldbus equipment: pressure unit) 7) With display (setting acc. to specifications, Order 7 code "Y2" or "Y22" required), lid with glass panel 7) Power supply units see Chap. 7 "Supplementary Components". Included in delivery of the device: Quick-start guide Sealing ring ) Only with "Standard" process connection" 2) Not in conjunction with electrical connection option A. ) Only available together with electrical connection options B, C or G. 4) Eplosion protection acc. to FM/CSA: suitable for installations according to NEC 500/505. 5) Only together with HART electronics. ) Without cable gland. 7) Display cannot be turned. Siemens FI US Edition /87

17 Siemens AG 207 SITRANS P00 with PMC connection Selection and Ordering data Order code Further designs HART PA FF Add "-Z" to Article No. and specify Order code. Cable socket for M2 plug Stainless steel A5 Rating plate inscription (instead of English) German B0 French B2 Spanish B Italian B4 English rating plate B2 Pressure units in inh 2 0 and/or psi Quality Inspection Certificate (5-point characteristic C curve test) according to IEC Inspection certificate C2 Acc. to EN Factory certificate C4 Acc. to EN Setting of the upper saturation limit of the D05 output signal to 22.0 ma Degree of protection IP5/IP8 D2 (only for M20.5 and ½-4 NPT) Mounting Weldable sockets for standard ½" P0 threaded connection Weldable socket for minibolt connection " (incl. screw 5/-8 UNC-2B and washer) P02 Selection and Ordering data Order code Additional data HART PA FF Please add "-Z" to Article No. and specify Order code(s) and plain tet. Measuring range to be set Y0 ) Specify in plain tet (ma. 5 characters): Y0:... up to... mbar, bar, kpa, MPa, psi Stainless steel tag plate and entry in Y5 device variable (measuring point description) Ma. characters, specify in plain tet: Y5:... Measuring point tet (entry in device variable) Y Ma. 27 char., specify in plain tet: Y:... Entry of HART address (TAG) Y7 Ma. 8 char., specify in plain tet: Y7:... Setting of pressure indication in Y2 pressure units Specify in plain tet (standard setting: bar): Y2: mbar, bar, kpa, MPa, psi,... Note: The following pressure units can be selected: bar, mbar, mm H 2 O *), inh 2 O *), fth 2 O *), mmhg, inhg, psi, Pa, kpa, MPa, g/cm 2, kg/cm 2, Torr, ATM or % *) ref. temperature 20 C Setting of pressure indication in non-pressure Y22 + units 2) Y0 Specify in plain tet: Y22:... up to... l, m, m, USg,... (specification of measuring range in pressure units "Y0" is essential, unit with ma. 5 characters) Preset bus address Y25 possible between and 2 Specify in plain tet: Y25:... Only "Y0" and "Y2" can be factory preset = available ) Measuring accuracies for PROFIBUS PA transmitters with Option Y0 are calculated in the same way as for HART devices. 2) Preset values can only be changed over SIMATIC PDM. /88 Siemens FI US Edition

18 Siemens AG 207 Dimensional drawings SITRANS P00 with PMC connection Ø 9 (.58) (2.) H 2 = appro.,8 (.4) H = appro. 20 (4.72) 9 (2.72) 2 (.02) 2,5 (.04) 82 SITRANS P00 pressure transmitters for gauge pressure, with PMC connection, dimensions in mm (inch) The diagram shows a SITRANS P00 with an eample of a flange. In this drawing the height is subdivided into H and H 2. H = Height of the SITRANS P00 up to a defined cross-section H 2 = Height of the flange up to this defined cross-section Only the height H 2 is indicated in the dimensions of the flanges. PMC Style Standard H 2 DN PN D H mm (.") Appro..8 mm (.4 ) M44,25 Ø,4 (.) Ø 2,7 (.05) D 20,9 (0.82) Ø, (.44) Ø 58,9 (2.2) ) Ø 8 (0.) 25,4 () 7,8 (0.7) PMC Style Mini bolt H 2 DN PN D H 2 2. mm (.0") Appro.. mm (. ) D ) O-ring surface (bore hole Ø 8 mm (0. ) without burr) PMC Style Standard (left) and PMC Style Minibolt (right) weldable sockets, dimensions in mm (inch) Material: Stainless steel, mat. No / L Siemens FI US Edition /89