ic-hg 3 A LASER SWITCH
|
|
- Audra Parker
- 6 years ago
- Views:
Transcription
1 Rev B3, Page 1/21 FEATURES Six channel laser switch from CW up to 200 MHz CW operation with up to 500 ma per channel Pulsed operation with up to 1.5 A per channel Spike-free switching of the laser current 6 x 1 channels with TTL inputs 3 x 2 channels with LVDS inputs Operates as six independent voltage-controlled current sinks Outputs (LDKx) are 12 V capable for blue/green laser diodes Fast and slow switching mode Simple current control at pins CIx CIx voltage < 3 V for full CW current Wide supply voltage range from 3 to 5.5 V All channels can be paralleled for up to 3 A CW and 9 A pulsed operation Multiple ic-hg can be connected in parallel for higher currents Open drain error output Thermal shutdown APPLICATIONS Pump lasers Laser projection Laser TV Data transmission TOF camera lighting LIDAR lighting Camera lighting PACKAGES QFN28 5 mm x 5 mm BLOCK DIAGRAM ic-hg LDK1 EN1 + - n AGND1 LDK2 EN2 n AGND2 EN3 EN4 LDK3 AGND3 LDK4 AGND4 EN5 EN6 LDK5 AGND5 LDK6 AGND6 80M NER ELVDS 60M n 40M 20M Power n Temperature Monitor GND Copyright 2010, 2018 ic-haus
2 Rev B3, Page 2/21 DESCRIPTION Six channel Laser Switch ic-hg enables the spikefree switching of laser diodes with well-defined current pulses at frequencies ranging from DC to 200 MHz. The diode current is determined by the voltages at pins CIx. The six fast switches are controlled independently via TTL inputs. Input ELVDS = hi selects LVDS type inputs and three channel mode. The laser diode can thus be turned on and off or switched between different current levels (LDKx connected) defined by the voltages at CIx. Each channel can be operated up to 500 ma CW and 1500 ma pulsed current depending on the frequency, duty cycle and heat dissipation. The integrated thermal shutdown feature protects the ic-hg from damage by excessive temperature TTL slow switch mode is selected with 30 and LVDS slow switch mode with 70 at input ELVDS.
3 Rev B3, Page 3/21 PACKAGING INFORMATION QFN28 5 mm x 5 mm to JEDEC PIN CONFIGURATION QFN28 5 mm x 5 mm HG code PIN FUNCTIONS No. Name Function 1 Current control voltage channel 1 2 Current control voltage channel 2 3 Current control voltage channel 3 4 GND Ground 5 Current control voltage channel 4 6 Current control voltage channel 5 7 Current control voltage channel 6 8 AGND6 Analog ground channel 6 9 LDK6 Laser diode cathode channel 6 10 AGND5 Analog ground channel 5 11 LDK5 Laser diode cathode channel 5 12 AGND4 Analog ground channel 4 13 LDK4 Laser diode cathode channel 4 14 EN6 TTL switching input channel 6 Negative LVDS Input channel 5 and 6 15 EN5 TTL switching input channel 5 Positive LVDS Input channel 5 and 6 16 EN4 TTL switching input channel 4 Negative LVDS Input channel 3 and 4 17 EN3 TTL switching input channel 3 Positive LVDS Input channel 3 and 4 18 Supply voltage 19 ELVDS TTL/LVDS Fast/Slow Input selector 20 EN2 TTL switching input channel 2 Negative LVDS Input channel 1 and 2 21 EN1 TTL switching input channel 1 Positive LVDS Input channel 1 and 2 22 NER Error monitor output 23 LDK3 Laser diode cathode channel 3 24 AGND3 Analog ground channel 3 25 LDK2 Laser diode cathode channel 2 26 AGND2 Analog ground channel 2 27 LDK1 Laser diode cathode channel 1 28 AGND1 Analog ground channel 1 The Thermal Pad is to be connected to a Ground Plane (GND, AGND1... 6) on the PCB. Only pin 1 marking on top or bottom defines the package orientation ( HG label and coding is subject to change).
4 Rev B3, Page 4/21 PACKAGE DIMENSIONS QFN28-5x5 All dimensions given in mm. This package falls within JEDEC MO-220-VHHD-1. RECOMMENDED PCB-FOOTPRINT R0.15 SIDE TOP 5 BOTTOM drb_qfn28-2_pack_1, 10:1
5 Rev B3, Page 5/21 ABSOLUTE MAXIMUM RATINGS Beyond these values damage may occur; device operation is not guaranteed. Item Symbol Parameter Conditions Unit No. Min. Max. G001 Voltage at V G002 I() Current in ma G003 V(CI) Voltage at V G004 V() Voltage at EN1... 6, AGND1... 6, ELVDS, NER V G005 V(LDK) Voltage at LDK V G006 I(LDK) Current in LDK DC current ma G007 I(AGND) Current in AGND DC current ma G008 I() Current in... 6, EN1... 6, ELVDS ma G009 I(NER) Current in NER ma G010 Vd() ESD Susceptibility at all pins HBM 100 pf discharged through 1.5 kω 2 kv G011 Tj Operating Junction Temperature C G012 Ts Storage Temperature Range C THERMAL DATA Item Symbol Parameter Conditions Unit No. Min. Typ. Max. T01 Ta Operating Ambient Temperature Range (extended range on request) C T02 Rthja Thermal Resistance Chip/Ambient Mounted onto the Evaluation Board HG1D 25 K/W T03 RthjTP Thermal Resistance Chip/Thermal Pad 4 K/W All voltages are referenced to ground unless otherwise stated. All currents flowing into the device pins are positive; all currents flowing out of the device pins are negative.
6 Rev B3, Page 6/21 ELECTRICAL CHARACTERISTICS Operating Conditions: = V, AGND = GND, Tj = C unless otherwise stated Item Symbol Parameter Conditions Unit No. Min. Typ. Max. Total Device (x = ) 001 Permissible Supply Voltage V 002 I() Supply Current in CW operation 10 ma 003 I() Supply Current in pulsed operation, f(enx) = 200 MHz 700 ma 004 V(LDKx) Permissible Voltage at LDKx V 005 V(NER) Permissible Voltage at NER V 006 Vc()hi Clamp Voltage hi at LDKx I(LDK) = 10 ma V 007 Vc(NER) Clamp Voltage hi at NER I(NER) = 1 ma V 008 Vc(CIx)hi Clamp Voltage hi at CIx Vc(CIx) = V(CIx) ; I(CI) = 10 ma, other pins open 009 Vc()hi Clamp Voltage hi at ENx, ELVDS Vc() = V() ; I() = 1 ma, other pins open 010 Vc()lo Clamp Voltage lo at, LDKx, CIx, ENx, AGNDx, ELVDS, NER Laser Control LDK1... 6,... 6 (x = ) 101 Icw(LDKx) Permissible CW Current in LDKx (per channel) 102 Vs(LDKx) Saturation Voltage at LDKx I(LDKx) = 450 ma, V(CIx) = V(CIx)@I(LDKx) = 500 ma V V I() = -10 ma, other pins open V 500 ma 1.5 V 103 I0(LDKx) Leakage Current in LDKx ENx = lo, V(LDKx) = 12 V 100 µa 104 tr() LDKx Current Rise Time Fast Iop(LDKx) = 500 ma, I(LDKx): 10% 90% Iop, V(ELVDS) = 0 V or 105 tf() LDKx Current Fall Time Fast Iop(LDKx) = 500 ma, I(LDKx): 90% 10% Iop, V(ELVDS) = 0 V or 106 tr() LDKx Current Rise Time Slow Iop(LDKx) = 500 ma, I(LDKx): 10% 90% Iop, V(ELVDS) = 30% or 70%, = 5 V 107 tf() LDKx Current Fall Time Slow Iop(LDKx) = 500 ma, I(LDKx): 90% 10% Iop, V(ELVDS) = 30% or 70%, = 5 V 108 tr() LDKx Current Rise Time Slow Iop(LDKx) = 500 ma, I(LDKx): 10% 90% Iop, V(ELVDS) = 30% or 70%, = 3.3 V 109 tf() LDKx Current Fall Time Slow Iop(LDKx) = 500 ma, I(LDKx): 90% 10% Iop, V(ELVDS) = 30% or 70%, = 3.3 V 110 tp() Propagation Delay Fast V(ENx) I(LDKx) V(ELVDS) = 0 V or, Differential LVDS Rise and Fall Time < 0.5 ns 1 ns 1 ns ns ns ns ns ns 111 CR() Current Matching all Channels V(CIx) Permissible Voltage at CIx -0.3 V 113 Vt(CIx) Threshold Voltage at CIx I(LDKx) < 5 ma V 114 V(CIx) Operating Voltage at CIx I(LDKx) = 500 ma, V(LDKx) > 1.8 V V 115 Ipd(CIx) Pull-Down Current at CIx V(CIx) = V µa 116 C(CIx) Capacity at CIx V(CIx) = 2 V pf 117 Vc(LDKx) Clamp Voltage at LDKx I(LDKx) = 100 ma, tclamp < 1 ms, tclamp/t < 1: V 118 tskc() Channel to Channel Skew 160 ps 119 tskp() Part to Part Skew best to worst 4 ns Input EN (x = ) 201 Vt(TTL)hi Input Threshold Voltage hi V(ELVDS) < 35%, TTL 2 V 202 Vt(TTL)lo Input Threshold Voltage lo V(ELVDS) < 35%, TTL 0.8 V 203 Vhys(TTL) Hysteresis Vhys() = Vt()hi Vt()lo; V(ELVDS) < 35%, TTL 50 mv Projected values by sample characterization Projected values by simulation
7 Rev B3, Page 7/21 ELECTRICAL CHARACTERISTICS Operating Conditions: = V, AGND = GND, Tj = C unless otherwise stated Item Symbol Parameter Conditions Unit No. Min. Typ. Max. 204 I(ENx) Pulldown Current V(ELVDS) < 35%, V() = 0.8 V..., TTL µa 205 R(ENx) Differential Input Impedance at ENx V(ELVDS) > 65%, V(ENx) < 1.4 V, LVDS 206 Vdiff Differential Voltage Vdiff = V(EN1,3,5) V(EN2,4,6) ; V(ELVDS) > 65%, LVDS kω 200 mv 207 V() Input Voltage Range V(ELVDS) > 65%, LVDS Input ELVDS 301 V(ELVDS) Voltage at ELVDS ELVDS open % 302 Ri(ELVDS) kω 303 Vt(ELVDS) Threshold Voltage TTL Fast to TTL Slow 304 Vt(ELVDS) Threshold Voltage TTL Slow to Error 305 Vt(ELVDS) Threshold Voltage Error to LVDS Slow 306 Vt(ELVDS) Threshold Voltage LVDS Slow to LVDS Fast % % % % 307 Vhys() Hysteresis mv Ouput NER 401 Vsat(NER) Saturation Voltage at NER ELVDS open, I(NER) = 2 ma 0.6 V 402 I(NER) Current in NER ELVDS open, V(NER) > 0.6 V ma Overtemperature 501 Toff Overtemperature Shutdown rising temperature C 502 Ton Overtemperature Release falling temperature C 503 Thys Hysteresis Toff Ton 5 C Power On 601 VON Power On Voltage rising voltage 2.9 V 602 VOFF Power Down Voltage falling voltage 1.5 V 603 Vhys Hysteresis mv V
8 Rev B3, Page 8/21 CONFIGURATION INPUT ELVDS Pin ELVDS selects between 6 channel TTL mode or 3 channel LVDS mode and chooses slow or fast switching speed. The unconnected pin ELVDS is an error condition signaled at pin NER with the laser current disabled. Pin ELVDS connected to GND selects the six channel fast TTL mode. Pin ELVDS connected to 30% selects the six channel slow TTL mode. Pin ELVDS connected to 70% selects the three channel slow LVDS mode. Pin ELVDS connected to selects the three channel fast LVDS mode. An easy way to set the slow operation mode for TTL and LVDS mode is to connect a voltage divider at pin ELVDS. Figure 1 shows the recommended voltage divider for slow TTL mode and Figure 2 shows the recommended voltage divider for slow LVDS mode. Figure 1: TTL Slow Figure 2: LVDS Slow DIGITAL INPUTS EN1...6 EN1...6 are the digital switching inputs. With pin ELVDS set to 6 channel TTL mode, each pin ENx enables the current sink at the respective LDKx. With pin ELVDS set to 3 channel LVDS mode, the odd ENx pins are the positive and the even ENx pins are the negative LVDS inputs. EN1 and EN2 control LDK1 and LDK2, EN3 and EN4 control LDK3 and LDK4 and EN5 and EN6 control LDK5 and LDK6. For correct LVDS operation 100 Ω terminating resistors between the respective EPx and ENx pins, very close to the inputs, are strongly recommended. Input pins from unused channels have to be connected to GND (TTL operation) resp. EPx to GND and ENx to (LVDS operation).
9 Rev B3, Page 9/21 ANALOG CURRENT CONTROL VOLTAGE INPUTS...6 The voltage at pins...6 sets the current in pins LDK Figures 3 and 4 show the temperature dependency of the current in a single LDKx output versus the voltage at CIx for a typical device. Figures 5 and 6 show the min., typ. and max. variations between devices at 27 C temperature. The voltage at pins LDKx is 2.5 V. Figure 3: I(LDKx) vs. V(CIx) at = 5 V Figure 4: I(LDKx) vs. V(CIx) at = 3.3 V Figure 5: I(LDKx) vs. V(CIx) at = 5 V Figure 6: I(LDKx) vs. V(CIx) at = 3.3 V
10 Rev B3, Page 10/21 LASER OUTPUTS LDK1...6 C2 EN1 EN2 EN3 EN4 EN5 EN6 ELVDS ic-hg + - CLDA1 CLDA2 CLDA3 CLDA4 100μF C3 LD1 Figure 7: Current loop LDK1 AGND1 LD2 LDK2 AGND2 LDK1...6 are the current outputs for the laser diode LDK3 cathode. For high speed operation, connect the laser AGND3 diode as close as possible to this pins to minimize the LDK4 inductance. To ensure a high switching speed, it is im- AGND4 portant to minimise the inductance of the whole current loop (cf. Figure 7, marked red) consisting LDK5 of ic-hg (pins LDKx and AGNDx), the laser diode AGND5 (anode and cathode), the backup capacitors asldk6 well as the enclosed area. It may still be necessary though to use an R/C AGND6 RNER snubber network for damping L/C oscillations. 10K 80% 60% CLDA1 100μF CLDA2 NER NERROR CLDA3 CLDA4 Depending on the residual inductance in the laser current path and the actual laser current, fast free-wheeling diodes from LDKx to VLDA may be required (cf. Figure 8, diode D1) to protect the outputs. The anode of the free-wheeling diode should be close to the to be protected LDKx output and the cathode close to the backup capacitors at VLDA for the free-wheeling current to be dumped into, when switching the respective channel off. Figure 9 shows the typical output characteristics of LDKx. The left hand side of the diagram is the RDSon region where the current depends strongly on the voltage at LDKx. The right hand side of the diagram is the LD3 current source region where the current depends only somewhat on the voltage at LDKx. Only the current LD4 source region is to be used. I(LDKx) [A] LD5 LD6 C2 40% 20% ic-hg GND Power Temperature Monitor D1 LDK1 C3 LD EN1 EN2 + - AGND1 LDK2 Figure 8: Free-wheeling diode AGND2 LD2 LD3 V(LDKx) [V] Figure 9: Output Characteristics of LDKx EN3 PULSED OPERATION LDK3 AGND3 LD4 EN4 EN5 AGND4 The current for pulsed operation may be higher than for CW operation. Therefore the RMS LDK5 current of the pulse train has to be considered. LDK4 AGND5 With I CWmax from LD5Electrical Characteristics No. 101 and pulses < 10 µs. So for a single channel operated with a 50% duty cycle, the max. laser current becomes LD6 EN6 80% LDK6 AGND6 I pulsemax = I CWmax repetition time(t) NER pulse time(t) RNER 10K NERROR (1) I pulsemax = 500 ma 2 = 707 ma ELVDS 60% 40% 20% Power Temperature Monitor GND
11 Rev B3, Page 11/21 ANALOG GROUNDS AGND1...6 AGND1...6 are the ground pins for the channels. It is recommended to connect all AGND1...6 pins to GND. ERROR OUTPUT NER The open drain pin NER is a low-active error output. Signalled errors are ELVDS open or at 50%, undervoltage and thermal shutdown. THERMAL SHUTDOWN ic-hg is protected by an integrated thermal shutdown feature. When the shutdown temperature is reached all channels are disabled. Falling temperature after this shutdown will unconditionally enable all channels again. Necessary precaution to prevent damage of the laser may be to also disable any external control circuits for the laser output power or current control during thermal shutdown. The error signal at pin NER can be used to e.g. disable the control circuit.
12 Rev B3, Page 12/21 APPLICATION EXAMPLES..12V CLDA1 100μF CLDA2 CLDA3 CLDA V C1 C2 ic-hg C3 LDK1 EN+LVDS EN1 AGND1 RLVDS LDK2 EN-LVDS EN2 AGND2 CI LDK3 CI EN3 AGND3 LDK4 EN4 AGND4 LDK5 EN5 AGND5 LDK6 EN6 AGND6 RNER 10K NER NERROR 80% ELVDS 60% 40% 20% Power Temperature Monitor GND Figure 10: 1 channel LVDS fast
13 Rev B3, Page 13/21..12V CLDA1 100μF CLDA2 CLDA3 CLDA V C1 C2 ic-hg C3 LDK1 EN+LVDS EN1 AGND1 RLVDS LDK2 EN-LVDS EN2 AGND2 CI LDK3 CI EN3 AGND3 LDK4 EN4 AGND4 LDK5 EN5 AGND5 LDK6 EN6 AGND6 RNER 10K RELVDS1 3.32k 80% NER NERROR ELVDS 60% RELVDS2 7.5k 40% 20% Power Temperature Monitor GND Figure 11: 1 channel LVDS slow
14 Rev B3, Page 14/21..12V CLDA1 100μF CLDA2 CLDA3 CLDA V C1 C2 ic-hg C3 LDK1 ENTTL EN1 AGND1 + - LDK2 EN2 AGND2 CI LDK3 CI EN3 AGND3 LDK4 EN4 AGND4 LDK5 EN5 AGND5 LDK6 EN6 AGND6 RNER 10K NER NERROR ELVDS 80% 60% 40% 20% Power Temperature Monitor GND Figure 12: 1 channel TTL fast
15 Rev B3, Page 15/21..12V CLDA1 100μF CLDA2 CLDA3 CLDA V C1 C2 ic-hg C3 LDK1 ENTTL EN1 AGND1 + - LDK2 EN2 AGND2 CI LDK3 CI EN3 AGND3 LDK4 EN4 AGND4 LDK5 EN5 AGND5 LDK6 EN6 AGND6 RNER 10K RELVDS1 7.5k 80% NER NERROR ELVDS 60% RELVDS2 3.32k 40% 20% Power Temperature Monitor GND Figure 13: 1 channel TTL slow
16 Rev B3, Page 16/21 GND ic-hg CLDA4 LD3 Monitor Power RLVDS3 C C2 C1 CLDA2 100 RLVDS2 AGND1 AGND3 LDK5 100 LDK1 - AGND6 EN+LVDS2 LD2 EN-LVDS V EN1..12V LD1 LDK2 40% C3 LDK6 CLDA4 NERROR 10K RNER NER EN6 10K EN3 EN+LVDS3 LDK3 ELVDS EN+LVDS1 AGND5 100 RLVDS3 EN4 EN-LVDS3 EN2 AGND4 EN-LVDS1 LDK4 AGND2 CLDA1 EN5 RLVDS1 C1 100μF LD1 RLVDS2 LD2 LD3 CLDA1 20% 80% RNER Temperature CLDA3 CLDA3 CLDA2 100μF % C3 RLVDS1 Figure 14: 3 channel LVDS fast
17 Rev B3, Page 17/21..12V ENTTL3 C1 C2 EN1 EN6 + - CLDA1 100μF GND CLDA2 Power Temperature Monitor CLDA3 CLDA4 C3 AGND1 LD2 LDK3 AGND3 LD4 AGND5 NER LD5 LD V ENTTL1 ENTTL2 ENTTL4 ENTTL5 ENTTL6 EN2 EN3 EN4 EN5 ELVDS ic-hg 80% 60% 40% 20% LD1 LDK1 LDK2 AGND2 LD3 LDK4 AGND4 LDK5 LDK6 AGND6 RNER 10K NERROR Figure 15: 6 channel TTL fast
18 Rev B3, Page 18/21 EVALUATION BOARD ic-hg comes with an evaluation board for test purpose. Figures 16 and 17 show both the schematic and the component side of the evaluation board. Figure 16: Schematic of the evaluation board
19 Rev B3, Page 19/21 Figure 17: Evaluation board (component side) Figure 18: Evaluation board (solder side) with mounting option for heat sink
20 Rev B3, Page 20/21 REVISION HISTORY Rel. Rel. Date Chapter Modification Page B APPLICATIONS More applications added 1 BLOCK DIAGRAM Block diagram color changed to blue 1 LASER OUTPUTS LDK1...6 Output characteristics diagram added 10 ORDERING INFORMATION High-speed modules for SMD type laser sources added 21 ic-haus expressly reserves the right to change its products and/or specifications. An Infoletter gives details as to any amendments and additions made to the relevant current specifications on our internet website and is automatically generated and shall be sent to registered users by . Copying even as an excerpt is only permitted with ic-haus approval in writing and precise reference to source. The data specified is intended solely for the purpose of product description and shall represent the usual quality of the product. In case the specifications contain obvious mistakes e.g. in writing or calculation, ic-haus reserves the right to correct the specification and no liability arises insofar that the specification was from a third party view obviously not reliable. There shall be no claims based on defects as to quality in cases of insignificant deviations from the specifications or in case of only minor impairment of usability. No representations or warranties, either expressed or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or areas of applications of the product. ic-haus products are not designed for and must not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (Safety-Critical Applications) without ic-haus specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems. ic-haus products are not designed nor intended for use in military or aerospace applications or environments or in automotive applications unless specifically designated for such use by ic-haus. ic-haus conveys no patent, copyright, mask work right or other trade mark right to this product. ic-haus assumes no liability for any patent and/or other trade mark rights of a third party resulting from processing or handling of the product and/or any other use of the product. Software and its documentation is provided by ic-haus GmbH or contributors "AS IS" and is subject to the ZVEI General Conditions for the Supply of Products and Services with ic-haus amendments and the ZVEI Software clause with ic-haus amendments ( Release Date format: YYYY-MM-DD
21 Rev B3, Page 21/21 ORDERING INFORMATION Type Package Options Order Designation ic-hg QFN28 5 mm x 5 mm ic-hg QFN28-5x5 General Purpose Evaluation Board Host adapter for high-speed modules Host adapter for high-speed modules High-speed module for C-mount laser diodes High-speed module for TO type laser diodes High-speed module for SMD type VCSEL arrays, laser diodes or LEDs High-speed module for SMD type VCSEL arrays, laser diodes or LEDs (alternative pad layout) ic-hg EVAL HG1D ic-hg EVAL HG2D with heat-sink assembly kit ic-hg EVAL HG2D-HSK ic-hg icsy HG2M ic-hg icsy HG8M ic-hg icsy HG20M ic-hg icsy HG21M Please send your purchase orders to our order handling team: Fax: +49 (0) dispo@ichaus.com For technical support, information about prices and terms of delivery please contact: ic-haus GmbH Tel.: +49 (0) Am Kuemmerling 18 Fax: +49 (0) D Bodenheim Web: GERMANY sales@ichaus.com Appointed local distributors:
ic-hg 3 A LASER SWITCH
Rev B3, Page 1/21 FEATURES Six channel laser switch from CW up to 200 MHz CW operation with up to 500 ma per channel Pulsed operation with up to 1.5 A per channel Spike-free switching of the laser current
More informationic-hgp 3 A HIGH-SIDE LASER SWITCH
Laser ichgp 3 A HIGHSIDE LASER SWITCH Rev A, Page /20 FEATURES Six channel laser switch from CW up to 200 MHz CW operation with up to 500 ma per channel Pulsed operation with up to.5 A per channel Spikefree
More informationic HB ic-hb TRIPLE 155 MHz LASER SWITCH VDD VTTL LDK2 LDKB CIB SYNB ENB EPB CI2 SYN2 EN2 EP2 CI1 SYN1 EN1 EP1 NER TTL GND AGNDB Rev A4, Page 1/8
TRIPLE 55 MHz LSER SWITCH Rev 4, Page /8 FETURES Laser switch for frequencies from CW up to 55 MHz Spike-free switching of the laser currents Three channels with independent current control at pins CIx
More informationic HK/B OVERTEMP. SHUTDOWN
Laser Rev F2, Page 1/1 FEATURES Laser switch for frequencies from CW up to 155 MHz Spike-free switching of the laser current Dual switching inputs with independent current control Operates as a voltage-controlled
More informationic-sg85 BLCC SG1C Infrared LED
Rev B4, Page 1/6 FEATURES Emission peak at 850 nm matched to silicon sensors Optimized irradiance pattern High temperature range -40 to 125 C High optical output power Fast switching speed APPLICATIONS
More informationic-hk, ic-hkb 155 MHz LASER SWITCH
MHz LASER SWITCH Rev E3, Page /9 FEATURES Laser switch for frequencies from CW up to MHz Spike-free switching of the laser current Dual switching inputs with independent current control Operates as a voltage-controlled
More informationic-mj LOW-POWER HALL SENSOR
Rev C1, Page 1/10 FEATURES Hall sensor for absolute evaluation of magnetic field strength Pulsed cyclic measurements (interrupted), permanently, or triggered Sensitivity adjustable in two stages Digital
More informationic-dn ic-dn LOWSIDE SWITCH 3-pin configuration Rev C1, Page 1/10
Rev C1, Page 1/10 FEATURES 36 V lowside switch/level shifter Decoupling of input and output reference voltages permits control by 5 V logic 200 ma of output current Short-circuit protected Output with
More informationic-tl46 BLCC SD1C Blue LED - SMD, 3.4 mm spot size
Rev A3, Page 1/7 FEATURES Emission peak at 460 nm Optimized irradiance pattern Temperature range -40 to 125 C High switching speed Packages suitable for SMT mounting APPLICATIONS Illumination for high
More informationic-ge100 PWM RELAY/SOLENOID DRIVER
Rev B1, Page 1/12 FEATURES Current control for inductive actuators at 24 V (10 to 36 V) Power saving and power dissipation reduced switching Individual setting of energising and hold current Contact conserving
More informationic-tl46 TO46-2L1 Blue LED
Rev B1, Page 1/6 FEATURES Emission peak at 460 nm Optimized irradiance pattern Temperature range -40 C to 100 C High efficiency LED chip Fast switching speed TO-46 package for flexible mounting Option:
More informationic-hc ULTRA FAST DUAL HV-KOMPARATOR
Rev A, Page /0 FEATURES Independent input supply voltage range up to 36 V Input voltage range down to Differential input voltage of 36 V max. Separate digital supply Programmable hysteresis resp. hold
More informationic-lfh320 obga LFH1C PACKAGE SPECIFICATION
Rev A2, Page 1/6 PACKAGE VIEW RoHS compliant SIZE 5.0 mm x 5.0 mm drb_lfh1c-lfh320_0_pack_2, 5:1 PIN CONFIGURATION PIN FUNCTIONS (top view) No. Name Function Pixel #1 4 3 2 1 A B C D drc_lfh1c-lfh320_0_pack_3c,
More informationic-wj, ic-wjz LASER DIODE DRIVER
Rev C, Page / FEATURES Laser diode driver for continuous and pulsed operation (CW to 00 khz) up to 50 ma Averaging control of laser power Simple adjustment of the laser power via external resistor Adjustable
More informationic-wjb 2.7 V LASER DIODE DRIVER
Rev D1, Page 1/12 FEATURES Simple APC adjustment via an external resistor Continuous (CW) or pulsed operation of up to 00 khz Laser diode current of up to 100 ma Adjustable watchdog for input signals Soft
More informationic-ge100 PWM RELAY/SOLENOID DRIVER
Rev A0.3, Page 1/11 FEATURES Current control for inductive actuators at 24 V (10 to 36 V) Power saving and power dissipation reduced switching Individual setting of energising and hold current Contact
More informationic-sn85 BLCC SN1C INFRARED LED
Rev B3, Page 1/6 FEATURES Emission peak at 850 nm matched to silicon sensors Optimized irradiance pattern High temperature range -40 to 125 C High optical output power Fast switching speed APPLICATIONS
More informationic-lfl x1 LINEAR IMAGE SENSOR
Rev A5, Page 1/9 FEATURES 256 active photo pixels of 56 µm at a gap and distortion free pitch of 63.5 µm (400 PI) Integrating L-V conversion followed by a sample & hold circuit High sensitivity and uniformity
More informationic-lfm 64x1 LINEAR IMAGE SENSOR
Rev A1, Page 1/9 FEATURES 64 active photo pixels of 56 µm at a pitch of 63.5 µm (400 PI) Integrating L-V conversion followed by a sample & hold circuit High sensitivity and uniformity over wavelength High
More informationic-sd85 olga SD2C3 Infrared LED
Rev C2, Page 1/6 FEATURES Emission peak at 850 nm matched to silicon sensors Broad irradiance pattern (lambertian profile) High temperature range -40 to 125 C High optical output power Fast switching speed
More informationic-nzn N-TYPE LASER DIODE DRIVER
Rev A, Page /6 FEATURES Peak value controlled laser diode driver for operation from CW up to 55 MHz Spikefree switching of laser currents of up to 300 ma Setting of laser power (APC) via external resistor
More informationic-mfn 8-FOLD FAIL-SAFE N-FET DRIVER
Rev A2, Page 1/13 FEATURES 8-fold level shift up to 40 V output voltage Inputs compatible with TTL and CMOS levels, 40 V voltage proof Level shift configurable to 5 V, 10 V or supply voltage Short-circuit-proof
More informationic-sm2l LINEAR AMR SENSOR (2 mm)
Rev C1, Page 1/8 FEATURES Magneto resistive position sensor based on the AMR effect Strong field sensor for 2 mm N/S pole pitch One sine/cosine cycle per pole width (averaged using a pair of N/S poles)
More informationic-vj, ic-vjz LASER DIODE CONTROLLER
FEATURES APPLICATIONS Laser diode driver of up to 250mA Averaging control of laser power Protective functions to prevent destruction of laser diode Laser-current monitor with current or voltage output
More informationic-ge PWM RELAY/SOLENOID DRIVER
Rev A2, Page 1/14 FEATURES Current control for inductive actuators at 24 V (10 to 36 V) High efficient current control up to 1 A Power saving and power dissipation reduced switching Individual setting
More informationic-nx 8-CHANNEL LIGHT-GRID PULSE DRIVER
Rev C1, Page 1/10 FEATURES 1 to 8 channels (hardware programmable) LED pulse current can be adjusted from 0.4 to 1.8 A via a single external low power resistor Positive pulse current temperature coefficient
More informationic-lsc 12-CHANNEL ACTIVE PHOTOSENSOR ARRAY
Rev C2, Page 1/8 FEATURES Monolithic array of independent photosensors with excellent matching Compact photosensor size of 800 µm x 300 µm enabling high-quality encoder scanning at reduced system dimensions
More informationic-lf x1 Linear Image Sensor
Rev A3, Page 1/9 FEATURES 128 active photo pixels of 56 µm at a 63.5 µm pitch (400 PI) Integrating L-V conversion followed by a sample & hold circuit High sensitivity and uniformity over wavelength High
More informationic-vx 3-CHANNEL DIFFERENTIAL LINE DRIVER
ic-x -CHANNEL DIFFERENTIAL LINE DRIER Rev C1, Page 1/11 FEATURES 6 current-limited and short-circuit-proof push-pull driver stages in complementary configuration Guaranteed driver current can be set to
More informationic-sm5l LINEAR AMR SENSOR (5 mm)
Rev B2, Page 1/7 FEATURES Magneto resistive position sensor based on the AMR effect Strong field sensor for 5 mm N/S pole pitch High interpolation due to a sine signal with few harmonics Low saturation
More informationic-we 3-CHANNEL 75 Ω LINE DRIVER
3-CHANNEL 75 Ω LINE DRIER Rev D1, Page 1/10 FEATURES APPLICATIONS 3 current-limited and short-circuit-proof push-pull drivers Built-in adaption to 75 Ω characteristic impedance High driver current of 300
More informationic-nzn N-TYPE LASER DIODE DRIVER
NTYPE LASER DIODE DRIVER Rev D, Page /6 FEATURES Peak value controlled laser diode driver for operation from CW up to 55 MHz Spikefree switching of laser currents of up to 300 ma Setting of laser power
More informationic-lf x1 LINEAR IMAGE SENSOR
Rev B1, Page 1/10 FEATURES 128 active photo pixels of 56 µm at a 63.5 µm pitch (400 DPI) Integrating L-V conversion followed by a sample & hold circuit High sensitivity and uniformity over wavelength High
More informationic OD/L ic-od, ic-odl OPTICAL POSITION-SENSITIVE DETECTOR (PSD) Rev D4, Page 1/11
Rev D4, Page 1/11 FEATURES Low-noise current amplifier with an integrated position-sensitive photodiode High reliability due to monolithical design Effective photodiode area: 2.6 mm x 0.88 mm (ic-od) resp.
More informationMIC4414/4415. General Description. Features. Applications. Typical Application. 1.5A, 4.5V to 18V, Low-Side MOSFET Driver
MIC4414/4415 1.5A, 4.5V to 18V, Low-Side MOSFET Driver General Description The MIC4414 and MIC4415 are low-side MOSFET drivers designed to switch an N-channel enhancement type MOSFET in low-side switch
More informationLD A, low quiescent current, low-noise voltage regulator. Applications. Description. Features
1 A, low quiescent current, low-noise voltage regulator Datasheet - production data Features DFN6 (3x3 mm) AEC-Q100 qualified Input voltage from 1.5 to 5.5 V Ultra-low dropout voltage (200 mv typ. at 1
More informationLDS8710. High Efficiency 10 LED Driver With No External Schottky FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
High Efficiency 10 LED Driver With No External Schottky FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier*)
More informationMIC4478/4479/4480. General Description. Features. Applications. Typical Application. 32V Low-Side Dual MOSFET Drivers
32V Low-Side Dual MOSFET Drivers General Description The MIC4478, MIC4479, and MIC4480 are low-side dual MOSFET drivers are designed to switch N-channel enhancement type MOSFETs from TTL-compatible control
More informationTSX339. Micropower quad CMOS voltage comparators. Related products. Applications. Description. Features
Micropower quad CMOS voltage comparators Datasheet - production data Related products Pin-to-pin and functionally compatible with the quad CMOS TS339 comparators See TSX3704 for push-pull output Applications
More informationMIC5524. Features. General Description. Applications. Typical Application. High-Performance 500mA LDO in Thin DFN Package
High-Performance 500mA LDO in Thin DFN Package General Description The is a low-power, µcap, low dropout regulator designed for optimal performance in a very-small footprint. It is capable of sourcing
More information1 A Constant-Current LED Driver with PWM Dimming
1 A Constant-Current Driver with PWM Dimming FEATURES Accurate 1 A current sink Up to 25 V operation on pin Low dropout 500 mv at 1 A current set by external resistor High resolution PWM dimming via EN/PWM
More informationApplications AP7350 GND
150mA ULTRA-LOW QUIESCENT CURRENT LDO with ENABLE Description The is a low dropout regulator with high output voltage accuracy. The includes a voltage reference, error amplifier, current limit circuit
More informationic-pn2656 PHASED ARRAY NONIUS ENCODER
Rev D1, Page 1/9 FEATURES Compact, 3-channel optical nonius encoder with differential scanning and analog sine/cosine outputs: 255 CPR (N), 256 CPR (M), 240 CPR (S), size 26 mm Phased-array design for
More informationMAX15070A/MAX15070B 7A Sink, 3A Source, 12ns, SOT23 MOSFET Drivers
General Description The /MAX15070B are high-speed MOSFET drivers capable of sinking 7A and sourcing 3A peak currents. The ICs, which are an enhancement over MAX5048 devices, have inverting and noninverting
More informationLM2903W. Low-power, dual-voltage comparator. Features. Description
Low-power, dual-voltage comparator Datasheet production data Features Wide, single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent of supply
More informationSMP LF: Surface Mount PIN Diode
DATA SHEET SMP1345-087LF: Surface Mount PIN Diode Applications Switches Attenuators Features Low-series resistance: 2 Ω maximum @ 10 ma Low total capacitance: 0.2 pf maximum @ 5 V QFN (2 x 2 mm) package
More informationCLA LF: Surface Mount Limiter Diode
DATA SHEET CLA4609-086LF: Surface Mount Limiter Diode Applications Low loss, high power limiters Receiver protectors Features Low thermal resistance: 25 C/W Typical threshold level: +36 dbm Low capacitance:
More informationic-ma3 ANGULAR HALL SENSOR WITH SIN/COS OUTPUT, CASCADABLE
Rev A2, Page 1/19 FEATURES Single supply operation from 3.0 V to 5.5 V For rotational speeds of up to 60,000 rpm Quad Hall array for high assembly tolerances High immunity to external stray fields Automatic
More informationSMP LF: Surface Mount PIN Diode
DATA SHEET SMP1324-087LF: Surface Mount PIN Diode Applications Switches Attenuators Features Low-series resistance: 0.75 Ω maximum @ 50 ma Low total capacitance: 1.5 pf maximum @ 30 V Excellent thermal
More informationSTOD1812. Power supply for PMOLED display panel. Features. Description. Applications
STOD1812 Power supply for PMOLED display panel Features Synchronous step-up converter Input voltage range from 2.5 V to 5.5 V Maximum output current 120 ma Efficiency: 75 % at I O = 10 ma - 30 ma; 85 %
More informationLM2903H. Low-power dual voltage comparator. Features. Description
LM23H Low-power dual voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent
More informationTriple Voltage Regulator TLE 4471
Triple Voltage Regulator TLE 4471 Features Triple Voltage Regulator Output Voltage 5 V with 450 ma Current Capability Two tracked Outputs for 50 ma and 100 ma Enable Function for main and tracked Output(s)
More informationLDS Channel Ultra Low Dropout LED Driver FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
6-Channel Ultra Low Dropout LED Driver FEATURES o Charge pump modes: 1-x, 1.33-x, 1.5-x, 2-x o Ultra low dropout PowerLite Current Regulator* o Drives up to 6 LEDs up to 32 ma each o Factory preset current
More informationTS3022. Rail-to-rail 1.8 V high-speed dual comparator. Applications. Description. Features
TS22 Rail-to-rail 1.8 V high-speed dual comparator Datasheet - production data Applications Telecom Instrumentation Signal conditioning High-speed sampling systems Portable communication systems Automotive
More informationFeatures. Applications
Ultra-Precision 1:8 LVDS Fanout Buffer with Three 1/ 2/ 4 Clock Divider Output Banks Revision 6.0 General Description The is a 2.5V precision, high-speed, integrated clock divider and LVDS fanout buffer
More informationMIC5271. Applications. Low. output current). Zero-current off mode. and reduce power. GaAsFET bias Portable cameras. le enable pin, allowing the user
µcap Negative Low-Dropout Regulator General Description The is a µcap 100mA negativee regulator in a SOT-23-this regulator provides a very accurate supply voltage for applications that require a negative
More informationHigh Speed PWM Controller
High Speed PWM Controller FEATURES Compatible with Voltage or Current Mode Topologies Practical Operation Switching Frequencies to 1MHz 50ns Propagation Delay to Output High Current Dual Totem Pole Outputs
More informationTS3011. Rail-to-rail high-speed comparator. Applications. Description. Features
Rail-to-rail high-speed comparator Datasheet - production data Applications Telecoms Instrumentation Signal conditioning High-speed sampling systems Portable communication systems Features Propagation
More informationFeatures. Applications
PCIe Fanout Buffer 267MHz, 8 HCSL Outputs with 2 Input MUX PrecisionEdge General Description The is a high-speed, fully differential 1:8 clock fanout buffer optimized to provide eight identical output
More informationLDS Channel Ultra Low Dropout LED Driver FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
6-Channel Ultra Low Dropout LED Driver FEATURES o Ultra low dropout PowerLite Current Regulator o Multi-mode charge pump: 1x, 1.5x, 2x o Drives up to 6 LEDs at 32mA each o Factory preset current value
More informationMIC General Description. Features. Applications. Typical Application. 3A Low Voltage LDO Regulator with Dual Input Voltages
3A Low Voltage LDO Regulator with Dual Input Voltages General Description The is a high-bandwidth, low-dropout, 3.0A voltage regulator ideal for powering core voltages of lowpower microprocessors. The
More informationMIC94161/2/3/4/5. Features. General Description. Applications. Typical Application. 3A High-Side Load Switch with Reverse Blocking
3A High-Side Load Switch with Reverse Blocking General Description The is a family of high-side load switches designed to operate from 1.7V to 5.5V input voltage. The load switch pass element is an internal
More informationHardware Documentation. Data Sheet HAL 549. Hall-Effect Sensor with Undervoltage Reset. Edition Jan. 30, 2009 DSH000022_003EN
Hardware Documentation Data Sheet HAL 549 Hall-Effect Sensor with Undervoltage Reset Edition Jan. 3, 29 DSH22_3EN DATA SHEET Copyright, Warranty, and Limitation of Liability The information and data contained
More informationZTL431AQ, ZTL431BQ ZTL432AQ, ZTL432BQ. Pin Assignments. Description. Features. Typical Application. Applications
AUTOMOTIVE COMPLIANT ADJUSTABLE PRECISION SHUNT REGULATOR Description The ZTL431AQ, ZTL431BQ, ZTL432AQ and ZTL432BQ are three terminal adjustable shunt regulators offering excellent temperature stability
More informationTLF1963. Data Sheet. Automotive Power. Low Dropout Linear Voltage Post Regulator TLF1963TB TLF1963TE. Rev. 1.0,
Low Dropout Linear Voltage Post Regulator TLF963TB TLF963TE Data Sheet Rev.., 22--8 Automotive Power Table of Contents Table of Contents Overview.......................................................................
More informationFeatures. Applications
267MHz 1:2 3.3V HCSL/LVDS Fanout Buffer PrecisionEdge General Description The is a high-speed, fully differential 1:2 clock fanout buffer with a 2:1 input MUX optimized to provide two identical output
More informationPART OBSOLETE - NO ALTERNATE PART
EIGHT-CHANNEL CONSTANT CURRENT SINK WITH CURRENT MATCH Description The is an eight-channel constant current sink with current match used for LED driver. It uses an external resistor to set the current
More informationGENERAL DESCRIPTION APPLICATIONS FEATURES. Point of Loads Set-Top Boxes Portable Media Players Hard Disk Drives
January 2014 Rev. 1.5.0 GENERAL DESCRIPTION The XRP6657 is a high efficiency synchronous step down DC to DC converter capable of delivering up to 1.5 Amp of current and optimized for portable battery-operated
More informationHardware Documentation. Data Sheet HAL 300. Differential Hall Effect Sensor IC. Edition Nov. 24, 2008 DSH000016_002EN
Hardware Documentation Data Sheet HAL 300 Differential Hall Effect Sensor IC Edition Nov. 24, 2008 DSH000016_002EN HAL300 DATA SHEET Copyright, Warranty, and Limitation of Liability The information and
More informationMADR V to 250V Driver for High Power PIN Diode Switches Rev. V1. Functional Schematic. Features. Description. Pin Configuration 1
Features 20 V to 250 V Back Bias in Off State 200 ma Series Diode Bias Current at +25 C 50 ma Shunt Diode Bias Current at +25 C Propagation Delay less than 8 µs Low Quiescent Current Consumption 3 V or
More informationObsolete Product(s) - Obsolete Product(s)
General features Supply voltage range: 2.6V to 5.5V 17V Maximum output voltage STCF01 Step-up converter for cell phone camera flash LEDs Two current levels up to 300mA set with external resistors Dedicated
More informationPMD5003K. 1. Product profile. MOSFET driver. 1.1 General description. 1.2 Features. 1.3 Applications. Quick reference data
Rev. 0 6 November 2006 Product data sheet. Product profile. General description PNP low V CEsat Breakthrough In Small Signal (BISS) transistor and high-speed switching diode to protect the base-emitter
More informationHardware Documentation. Data Sheet. HAL 1xy. Hall-Effect Switch IC Family. Edition April 8, 2009 DSH000150_001EN
Hardware Documentation Data Sheet HAL 1xy Hall-Effect Switch IC Family Edition April 8, 2009 DSH000150_001EN HAL1xy DATA SHEET Copyright, Warranty, and Limitation of Liability The information and data
More informationSMP LF: Surface Mount PIN Diode for High Power Switch Applications
DATA SHEET SMP1304-085LF: Surface Mount PIN Diode for High Power Switch Applications Applications Low loss, high power switches Low distortion attenuators Features Low-thermal resistance: 35 C/W Suitable
More informationFeatures. Applications
High-Current Low-Dropout Regulators General Description The is a high current, high accuracy, lowdropout voltage regulators. Using Micrel's proprietary Super βeta PNP process with a PNP pass element, these
More informationIsolated High Side FET Driver
UC1725 Isolated High Side FET Driver FEATURES Receives Both Power and Signal Across the Isolation Boundary 9 to 15 Volt High Level Gate Drive Under-voltage Lockout Programmable Over-current Shutdown and
More informationPAM2861. Description. Pin Assignments. Features. Applications. A Product Line of. Diodes Incorporated 1A LED DRIVER WITH INTERNAL SWITCH PAM2861
1A LED DRIVER WITH INTERNAL SWITCH Description Pin Assignments The is a continuous mode inductive step-down converter, designed for driving single or multiple series connected LEDs efficiently from a voltage
More information1.5MHz 600mA, Synchronous Step-Down Regulator. Features
1.5MHz 600mA, Synchronous Step-Down Regulator General Description is designed with high efficiency step down DC/DC converter for portable devices applications. It features with extreme low quiescent current
More informationApplications. Monitor TV STB Datacom
18V, 3A SYNCHRONOUS DC-DC BUCK CONVERTER Description Pin Assignments The is a 500kHz fixed frequency, current mode, PWM synchronous buck (step-down) DC-DC converter, capable of driving a 3A load with high
More informationSTCS05A. 0.5 A max constant current LED driver. Features. Applications. Description
0.5 A max constant current LED driver Features Up to 40 V input voltage Less than 0.5 V voltage overhead Up to 0.5 A output current PWM dimming pin Shutdown pin LED disconnection diagnostic Slope control
More information1A 1.5MHz PFM/PWM Synchronous Step-Down Converter. January 2014 Rev FEATURES. Fig. 1: XRP6658 Application Diagram
January 2014 Rev. 1.6.0 GENERAL DESCRIPTION The XRP6658 is a synchronous current mode PWM step down (buck) converter capable of delivering up to 1 Amp of current and optimized for portable battery-operated
More informationPAM2421/ PAM2422/ PAM2423. Pin Assignments. Description NEW PRODUCT. Applications Features. Typical Applications Circuit
3A, 4.5A, 5.5A PWM STEP-UP DC-DC CONVERTER Description Pin Assignments The PAM242x devices are high-performance, fixed frequency, current-mode PWM step-up DC/DC converters that incorporate internal power
More informationSY84782U. General Description. Features. Typical Application. Low Power 2.5V 1.25Gbps FP/DFB Laser Diode Driver
Low Power 2.5V 1.25Gbps FP/DFB Laser Diode Driver General Description Features The is a single 2.5V supply, ultra-low power, small form factor laser diode driver for telecom/datacom applications. Intended
More informationMIC4812. Features. General Description. Applications. Typical Application
High Current 6 Channel Linear WLED Driver with DAM and Ultra Fast PWM Control General Description The is a high efficiency linear White LED (WLED) driver designed to drive up to six high current WLEDs
More information74LVC08A. Description. Pin Assignments. Features. Applications QUADRUPLE 2-INPUT AND GATES 74LVC08A. (Top View) Vcc 4B 4A 4Y 3B 3A 3Y
QUADRUPLE 2-INPUT AND GATES Description Pin Assignments The provides four independent 2-input AND gates. The device is designed for operation with a power supply range of 1.65V to 5.5V. The inputs are
More informationLD ma very low quiescent current linear regulator IC. applications. Description. Features
300 ma very low quiescent current linear regulator IC Datasheet - production data Applications Mobile phones Tablets Digital still cameras (DSC) Cordless phones and similar batterypowered systems Portable
More informationIFX1963. Data Sheet. Industrial Standard Power. 1.5A Low Dropout Linear Voltage Regulator IFX1963TBV IFX1963TEV. Rev. 1.
.5A Low Dropout Linear Voltage Regulator IFX963TBV IFX963TEV Data Sheet Rev.., 23-2-25 Industrial Standard Power Table of Contents Table of Contents Overview.......................................................................
More informationAN3134 Application note
Application note EVAL6229QR demonstration board using the L6229Q DMOS driver for a three-phase BLDC motor control application Introduction This application note describes the EVAL6229QR demonstration board
More informationML4818 Phase Modulation/Soft Switching Controller
Phase Modulation/Soft Switching Controller www.fairchildsemi.com Features Full bridge phase modulation zero voltage switching circuit with programmable ZV transition times Constant frequency operation
More informationPESD1LIN. 1. Product profile. LIN bus ESD protection diode in SOD General description. 1.2 Features. 1.3 Applications. Quick reference data
Rev. 01 26 October 2004 Product data sheet 1. Product profile 1.1 General description in very small SOD323 (SC-76) SMD plastic package designed to protect one automotive LIN bus line from the damage caused
More informationSMTYF. Low forward voltage TVS Transky. Features. Description. Complies with the following standards:
Low forward voltage TVS Transky Features High peak pulse power: 600 W (10/1000 µs) 4000 W (8/20 µs) Stand-off voltage 5 or 12 V Low forward voltage: 0.48 V @ 0.85 A @ 25 C K A Low clamping factor V CL
More informationCLA LF: Surface Mount Limiter Diode
DATA SHEET CLA4610-085LF: Surface Mount Limiter Diode Applications Low-loss, high-power limiters Receiver protectors Anode (Pin 1) Anode (Pin 3) Features Low thermal resistance: 73 C/W Typical threshold
More informationObsolete Product(s) - Obsolete Product(s)
Three-terminal 5 A adjustable voltage regulators Features Guaranteed 7 A peak output current Guaranteed 5 A output current Adjustable output down to 1.2 V Line regulation typically 0.005 %/V Load regulation
More informationBAS16J. 1. Product profile. Single high-speed switching diode. 1.1 General description. 1.2 Features. 1.3 Applications. 1.4 Quick reference data
Rev. 01 8 March 2007 Product data sheet 1. Product profile 1.1 General description, encapsulated in a SOD323F (SC-90) very small and flat lead Surface-Mounted Device (SMD) plastic package. 1.2 Features
More informationFeatures. Applications SOT-23-5
135MHz, Low-Power SOT-23-5 Op Amp General Description The is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply current,
More informationic-la 64X1 LINEAR IMAGE SENSOR
Rev 2, Page 1/8 FETURES 64 photosensors with 200µm pitch and an active area of 0.037mm 2 (ca. 183µm x 200µm) Integrating amplifiers and track-and-hold feature Low image lag Integration time can be set
More informationAP A SINGLE CHANNEL CURRENT-LIMITED LOAD SWITCH. Pin Assignments. Description NEW PRODUCT. Features. Applications. Typical Application Circuit
Description Pin Assignments The is single channel current-limited integrated highside power switches optimized for hot-swap applications. The devices have fast short-circuit response time for improved
More informationXRP A/1A Dual Channel 1.5MHz Sync. Step Down Converter GENERAL DESCRIPTION APPLICATIONS FEATURES TYPICAL APPLICATION DIAGRAM
November 2017 Rev. 1.2.1 GENERAL DESCRIPTION The XRP6668 is a dual channel synchronous current mode PWM step down (buck) converter capable of delivering up to 1 Amp of current per channel and optimized
More informationGENERAL DESCRIPTION APPLICATIONS FEATURES TYPICAL APPLICATION DIAGRAM
August 2012 Rev. 1.2.0 GENERAL DESCRIPTION The XRP7659 is a current-mode PWM stepdown (buck) voltage regulator capable of delivering an output current up to 1.5Amps. A wide 4.5V to 18V input voltage range
More informationic-nvh 6-BIT Sin/D FLASH CONVERTER
Rev D1, Page 1/13 FEATURES APPLICATIONS Fast flash converter Integrated glitch filter; minimum transition distance can be set using the optional resistor Selectable resolution of up to 64 steps per cycle
More information