Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Transcription

1 Kevin SEC/S Zhou Marshall Wang PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (4) (1) 1/1301-BMR 673 Uen Kevin Zhou 09/22/ F A Key Features Industry standard Sixteenth-brick x x 9.40 mm (1.30 x 0.90 x 0.37 in.) Wide Input range Vin Maximum 50 Watts total output power High efficiency, typ. 92 % at 5 V half load & 27 Vin Pre-biased start up 2250 Vdc input to output isolation Basic insulation according to UL Surface mount option Meets safety requirements according to IEC/EN/UL More than 4.9 million hours MTBF Technical Specification General Characteristics Input under voltage lockout Over temperature protection Output over voltage protection Output short circuit protection Remote control Highly automated manufacturing ensures quality ISO 9001/14001 certified supplier Safety Approvals Design for Environment Meets requirements in hightemperature lead-free soldering processes. Contents Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Electrical Specification 3.3 V, 15 A / 50 W PKU 5510E PI V, 10 A / 50 W PKU 5511E PI V, 4.2 A / 50 W PKU 5513E PI EMC Specification Operating Information Thermal Consideration Connections Mechanical Information Soldering Information Delivery Information Product Qualification Specification... 25

2 Kevin Zhou PRODUCT SPECIFICATION 2 (4) 1/1301-BMR 673 Uen Technical Specification 2 Kevin Zhou 09/22/2017 F Ordering Information Product program PKU 5510E PI PKU 5511E PI PKU 5513E PI Output A 5 10 A 12 V@ 4.2 A Product number and Packaging PKU 5511E n1n2n3 Options n1 n2 n3 n4 Mounting option Remote logic Lead length Packaging Options n 1 n 2 n 3 n 4 Description PI SI P LA LB LC /B /C Through hole Surface mount Negative logic* Positive logic 5.33 mm* 3.69 mm 4.57 mm 2.79 mm Tray Tape and Reel * Standard variant (i.e. no option selected). For example, the through hole version 5V product with short pin is PKU 5511E PILA. General Information Reliability The failure rate () and mean time between failures (MTBF= 1/) is calculated at max output power and an operating ambient temperature (TA) of +40 C. Flex uses Telcordia SR-332 Issue 2 Method 1 to calculate the mean steady-state failure rate and standard deviation (). Telcordia SR-332 Issue 2 also provides techniques to estimate the upper confidence levels of failure rates based on the mean and standard deviation. maximum concentration value of 0.1% by weight in homogeneous materials for lead, mercury, hexavalent chromium, PBB and PBDE and of 0.01% by weight in homogeneous materials for cadmium. Exemptions in the RoHS directive utilized in Flex products are found in the Statement of Compliance document. Flex fulfills and will continuously fulfill all its obligations under regulation (EC) No 1907/2006 concerning the registration, evaluation, authorization and restriction of chemicals (REACH) as they enter into force and is through product materials declarations preparing for the obligations to communicate information on substances in the products. Quality Statement The products are designed and manufactured in an industrial environment where quality systems and methods like ISO 9000, Six Sigma, and SPC are intensively in use to boost the continuous improvements strategy. Infant mortality or early failures in the products are screened out and they are subjected to an ATE-based final test. Conservative design rules, design reviews and product qualifications, plus the high competence of an engaged work force, contribute to the high quality of the products. Warranty Warranty period and conditions are defined in Flex General Terms and Conditions of Sale. Limitation of Liability Flex does not make any other warranties, expressed or implied including any warranty of merchantability or fitness for a particular purpose (including, but not limited to, use in life support applications, where malfunctions of product can cause injury to a person s health or life) The information and specifications in this technical specification is believed to be correct at the time of publication. However, no liability is accepted for inaccuracies, printing errors or for any consequences thereof. Flex reserves the right to change the contents of this technical specification at any time without prior notice. Mean steady-state failure rate, Std. deviation, 226 nfailures/h 18.3 nfailures/h MTBF (mean value) for the PKU-E series = 4.9 Mh. MTBF at 90% confidence level = 4.4 Mh Compatibility with RoHS requirements The products are compatible with the relevant clauses and requirements of the RoHS directive 2002/95/EC and have a

3 Kevin Zhou PRODUCT SPECIFICATION 3 (4) 1/1301-BMR 673 Uen Technical Specification 3 Kevin Zhou 09/22/2017 F Safety Specification General information Flex DC/DC converters and DC/DC regulators are designed in accordance with the safety standards IEC , EN and UL Safety of Information Technology Equipment. IEC/EN/UL contains requirements to prevent injury or damage due to the following hazards: Electrical shock Energy hazards Fire Mechanical and heat hazards Radiation hazards Chemical hazards On-board DC/DC converters, Power interface modules and DC/DC regulators are defined as component power supplies. As components they cannot fully comply with the provisions of any safety requirements without conditions of acceptability. Clearance between conductors and between conductive parts of the component power supply and conductors on the board in the final product must meet the applicable safety requirements. Certain conditions of acceptability apply for component power supplies with limited stand-off (see Mechanical Information and Safety Certificate for further information). It is the responsibility of the installer to ensure that the final product housing these components complies with the requirements of all applicable safety standards and regulations for the final product. Component power supplies for general use should comply with the requirements in IEC/EN/UL 60950/1 Safety of Information Technology Equipment. Product related standards, e.g. IEEE 802.3af Power over Ethernet, and ETS Power interface at the input to telecom equipment, operated by direct current (dc) are based on IEC/EN/UL with regards to safety. Flex DC/DC converters, Power interface modules and DC/DC regulators are UL recognized and certified in accordance with EN The flammability rating for all construction parts of the products meet requirements for V-0 class material according to IEC , Fire hazard testing, test flames 50 W horizontal and vertical flame test methods. For basic insulated products (see Safety Certificate) the output is considered as safety extra low voltage (SELV) if one of the following conditions is met: The input source provides supplementary or double or reinforced insulation from the AC mains according to IEC/EN/UL The input source provides functional or basic insulation from the AC mains and the product s output is reliably connected to protective earth according to IEC/EN/UL For functional insulated products (see Safety Certificate) the output is considered as safety extra low voltage (SELV) if one of the following conditions is met: The input source provides double or reinforced insulation from the AC mains according to IEC/EN/UL The input source provides basic or supplementary insulation from the AC mains and the product s output is reliably connected to protective earth according to IEC/EN/UL The input source is reliably connected to protective earth and provides basic or supplementary insulation according to IEC/EN/UL and the maximum input source voltage is 60 Vdc. Galvanic isolation between input and output is verified in an electric strength test and the isolation voltage (Viso) meets the voltage strength requirement for basic insulation according to IEC/EN/UL It is recommended to use a slow blow fuse at the input of each product. If an input filter is used in the circuit the fuse should be placed in front of the input filter. In the rare event of a component problem that imposes a short circuit on the input source, this fuse will provide the following functions: Isolate the fault from the input power source so as not to affect the operation of other parts of the system Protect the distribution wiring from excessive current and power loss thus preventing hazardous overheating Isolated DC/DC converters The product may provide basic or functional insulation between input and output according to IEC/EN/UL (see Safety Certificate), different conditions shall be met if the output of a basic or a functional insulated product shall be considered as safety extra low voltage (SELV).

4 EXUEFYA PRODUCT SPECIFICATION 1 (6) 2/1301-BMR 673 Technical 01 Uen Specification 4 SEC/D PKU 5500E (Julia You) series DC/DC Converters EDGJKLT A Absolute Maximum Ratings Characteristics min typ max Unit T P1 Operating Temperature (see Thermal Consideration section) C T S Storage temperature C V I Input voltage V V iso Isolation voltage (input to output test voltage) 2250 Vdc V tr Input voltage transient (tp 100ms) 100 V V RC Remote Control pin voltage (see Operating Information section) Positive logic option V Negative logic option V V adj Adjust pin voltage (see Operating Information section) V Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits in the Electrical Specification. If exposed to stress above these limits, function and performance may degrade in an unspecified manner. Fundamental Circuit Diagram

5 EXUEFYA PRODUCT SPECIFICATION 2 (6) 2/1301-BMR 673 Technical 01 Uen Specification 5 SEC/D PKU 5500E (Julia You) series DC/DC Converters EDGJKLT A Electrical Specification 3.3 V, 15 A / 50 W T P1 = -40 to +90ºC, V I = 18 to 75 V, unless otherwise specified under Conditions. Typical values given at: T P1 = +25 C, V I = 53 V I max I O, unless otherwise specified under Conditions. Additional C in = 100 µf. C out = 470 µf PKU 5510E PI Characteristics Conditions min typ max Unit V I Input voltage range V V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 6.6 μf P O Output power 0 50 W η Efficiency 50% of max I O, V i =27V 92 max I O, V i =27V 91 50% of max I O, V I = 53 V 89.5 max I O, V I = 53 V 90.2 P d Power Dissipation max I O W P li Input idling power I O = 0 A, V I = 53 V 1.4 W P RC Input standby power V I = 53 V (turned off with RC) 0.33 W f s Switching frequency % of max I O khz % V Oi V O Output voltage initial setting and accuracy T P1 = +25 C, V I = 53 V, I O = 15 A V Output adjust range See operating information V Output voltage tolerance band % of max I O V Idling voltage I O = 0 A V Line regulation max I O ±5 ±25 mv Load regulation V I = 53 V, 0-100% of max I O ±10 ±25 mv Load transient V tr V I = 53 V, Load step % of ±250 ±400 mv voltage deviation max I O, di/dt = 1 A/μs t tr Load transient recovery time see Note µs t r t s t f t RC Ramp-up time (from 10 90% of V Oi ) Start-up time (from V I connection to 90% of V Oi ) V I shut-down fall time (from V I off to 10% of V O ) % of max I O ms Ms max I O 3.75 Ms I O = 0 A 6.6 S RC start-up time max I O 85 Ms RC shut-down fall time (from RC off to 10% of V O ) max I O 0.35 Ms I O = 0 A 13 S I O Output current 0 15 A I lim Current limit threshold T P1 < max T P A I sc Short circuit current T P1 = 25ºC, see Note A C out Recommended Capacitive Load T P1 = 25ºC, µf V Oac Output ripple & noise See ripple & noise section, V Oi mvp-p OVP RC Over voltage protection T P1 = +25 C, V I = 53 V, 0-100% of max I O V Sink current, see Note 3 See operating information 0.5 ma Trigger level See operating information 1 V Note 1: 1500uF OS-CON cap used at load transient test Note 2: hiccup mode OCP, RMS value Note 3: Sink current drawn by external device connected to the RC pin. Minimum sink current required to guarantee activated RC function.

6 EXUEFYA PRODUCT SPECIFICATION 3 (6) 2/1301-BMR 673 Technical 01 Uen Specification 6 SEC/D PKU 5500E (Julia You) series DC/DC Converters EDGJKLT A Typical Characteristics 3.3 V, 15 A / 50 W PKU 5510E PI Efficiency Power Dissipation [%] 95 [W] V 27 V 53 V 75 V V 27 V 53 V 75 V Efficiency vs. load current and input voltage at T P1 = +25C. Output Characteristics [V] 3.40 Dissipated power vs. load current and input voltage at T P1 = +25 C. Current Limit Characteristics [V] V 27 V 53 V 75 V V 27 V 53 V 75 V Output voltage vs. load current at T P1 = +25 C. Output voltage vs. load current at I O > max I O, T P1 = +25 C.

7 EXUEFYA PRODUCT SPECIFICATION 4 (6) 2/1301-BMR 673 Technical 01 Uen Specification 7 SEC/D PKU 5500E (Julia You) series DC/DC Converters EDGJKLT A Typical Characteristics 3.3 V, 15 A / 50 W PKU 5510E PI Start-up Shut-down Start-up enabled by connecting V I at: T P1 = +25 C, V I = 53 V, I O = 15 A resistive load. Top trace: output voltage (2 V/div). Bottom trace: input voltage (50 V/div). Time scale: (5 ms/div). Shut-down enabled by disconnecting V I at: T P1 = +25 C, V I = 53 V, I O = 15 A resistive load. Top trace: output voltage (2 V/div). Bottom trace: input voltage (50 V/div). Time scale: (2 ms/div). Output Ripple & Noise Output Load Transient Response Output voltage ripple at: T P1 = +25 C, V I = 53 V, I O = 15 A resistive load. Trace: output voltage (10 mv/div). Time scale: (2 µs/div.). Output voltage response to load current stepchange ( A) at: T P1 =+25 C, V I = 53 V Top trace: output voltage (200 mv/div). Bottom trace: load current (5 A/div). Time scale: (0.2 ms/div). Output Voltage Adjust (see operating information) Passive adjust The resistor value for an adjusted output voltage is calculated by using the following equations: Output Voltage Adjust, Decrease: 511 Radj 10. % 22 k Output Voltage Adjust, Increase: % 511 Radj k % % Active adjust The output voltage may be adjusted using a voltage applied to the Vadj pin. This voltage is calculated by using the following equation: Vdesired 3.30 Vadj V 3.30 Example: Increase Vdesired = 3.50 V V = 1.37 V 3.30 Example: Increase 4% => V o = Vdc k = 220 k

8 EXUEFYA PRODUCT SPECIFICATION 5 (6) 2/1301-BMR 673 Technical 01 Uen Specification 8 SEC/D PKU 5500E (Julia You) series DC/DC Converters EDGJKLT A Typical Characteristics 3.3 V, 15 A / 50 W Output Current Derating, Vin=53V, test board 1 Output Current Derating, Vin=53V, test board 2 PKU 5510E PI m/s 2.0 m/s 1.5 m/s m/s 2.0 m/s 1.5 m/s m/s m/s m/s m/s 3 Nat. Conv. 3 Nat. Conv [ C] [ C] Available load current vs. ambient air temperature and airflow at V I = 53 V. See Thermal Consideration section. Available load current vs. ambient air temperature and airflow at V I = 53 V. See Thermal Consideration section. Output Current Derating, Vin=27V, test board 1 Output Current Derating, Vin=27V, test board m/s 2.0 m/s 1.5 m/s m/s 2.0 m/s 1.5 m/s m/s m/s m/s m/s 3 Nat. Conv. 3 Nat. Conv [ C] [ C] Available load current vs. ambient air temperature and airflow at V I = 27 V. See Thermal Consideration section. Available load current vs. ambient air temperature and airflow at V I = 27 V. See Thermal Consideration section. Test board 1: 254 x 254 mm, 35 µm (1 oz),8-layer test board Test board 2: 254 x 254 mm, 35 µm (1 oz),16-layer test board

9 EDGJKLT PRODUCT SPECIFICATION 2 (6) 2/1301-BMR 673 Technical 02 Uen Specification 9 SEC/D PKU 5500E (Julia You) series DC/DC Converters EXUEFYA B Electrical Specification 5 V, 10 A / 50 W T P1 = -40 to +90ºC, V I = 18 to 75 V, unless otherwise specified under Conditions. Typical values given at: T P1 = +25 C, V I = 53 V, max I O, unless otherwise specified under Conditions. Additional C in = 100 µf. C out = 330 µf PKU 5511E PI Characteristics Conditions min typ max Unit V I Input voltage range V V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 6.6 μf P O Output power 0 50 W η Efficiency 50% of max I O, V i =27V 92 max I O, V i =27V 91 50% of max I O, V I = 53 V 89 max I O, V I = 53 V 90 P d Power Dissipation max I O W P li Input idling power I O = 0 A, V I = 53 V 2 W P RC Input standby power V I = 53 V (turned off with RC) 0.44 W f s Switching frequency % of max I O khz % V Oi V O Output voltage initial setting and accuracy T P1 = +25 C, V I = 53 V, I O = 10 A V Output adjust range See operating information V Output voltage tolerance band % of max I O V Idling voltage I O = 0 A V Line regulation max I O ±5 ±25 mv Load regulation V I = 53 V, 0-100% of max I O ±10 ±25 mv Load transient V tr V I = 53 V, Load step % of ±300 ±500 mv voltage deviation max I O, di/dt = 1 A/μs t tr Load transient recovery time see Note µs t r t s t f t RC Ramp-up time (from 10 90% of V Oi ) Start-up time (from V I connection to 90% of V Oi ) V I shut-down fall time (from V I off to 10% of V O ) % of max I O ms ms max I O 0.6 ms I O = 0 A 5.9 S RC start-up time max I O 115 ms RC shut-down fall time (from RC off to 10% of V O ) max I O 1.3 ms I O = 0 A 6.2 S I O Output current 0 10 A I lim Current limit threshold T P1 < max T P A I sc Short circuit current T P1 = 25ºC, see Note 2 12 A C out Recommended Capacitive Load T P1 = 25ºC, µf V Oac Output ripple & noise See ripple & noise section, V Oi mvp-p OVP RC Over voltage protection T P1 = +25 C, V I = 53 V, 0-100% of max I O V Sink current, see Note 3 See operating information 0.5 ma Trigger level See operating information 1 V Note 1: 1000uF OS-CON cap used at load transient test Note 2: hiccup mode OCP, RMS value Note 3: Sink current drawn by external device connected to the RC pin. Minimum sink current required to guarantee activated RC function.

10 EDGJKLT PRODUCT SPECIFICATION 3 (6) 2/1301-BMR 673 Technical 02 Uen Specification 10 SEC/D PKU 5500E (Julia You) series DC/DC Converters EXUEFYA B Typical Characteristics 5 V, 10 A / 50 W PKU 5511E PI Efficiency Power Dissipation [%] 95 [W] V 27 V 53 V 75 V V 27 V 53 V 75 V Efficiency vs. load current and input voltage at T P1 = +25C. Output Characteristics Dissipated power vs. load current and input voltage at T P1 = +25 C. Current Limit Characteristics [V] [V] V V 27 V 53 V V 53 V V V Output voltage vs. load current at T P1 = +25 C. Output voltage vs. load current at I O > max I O, T P1 = +25 C.

11 EDGJKLT PRODUCT SPECIFICATION 4 (6) 2/1301-BMR 673 Technical 02 Uen Specification 11 SEC/D PKU 5500E (Julia You) series DC/DC Converters EXUEFYA B Typical Characteristics 5 V, 10 A / 50 W PKU 5511E PI Start-up Shut-down Start-up enabled by connecting V I at: T P1 = +25 C, V I = 53 V, I O = 10 A resistive load. Top trace: output voltage (2 V/div). Bottom trace: input voltage (20 V/div). Time scale: (2 ms/div). Shut-down enabled by disconnecting V I at: T P1 = +25 C, V I = 53 V, I O = 10 A resistive load. Top trace: output voltage (2 V/div). Bottom trace: input voltage (20 V/div). Time scale: (20 ms/div). Output Ripple & Noise Output Load Transient Response Output voltage ripple at: T P1 = +25 C, V I = 53 V, I O = 10 A resistive load. Trace: output voltage (5 mv/div). Time scale: (2 µs/div.). Output voltage response to load current stepchange ( A) at: T P1 =+25 C, V I = 53 V Top trace: output voltage (200 mv/div). Bottom trace: load current (2 A/div). Time scale: (0.5 ms/div). Output Voltage Adjust (see operating information) Passive adjust The resistor value for an adjusted output voltage is calculated by using the following equations: Output Voltage Adjust, Decrease: % 22 k Radj Output Voltage Adjust, Increase: % 511 k Radj % % Active adjust The output voltage may be adjusted using a voltage applied to the Vadj pin. This voltage is calculated by using the following equation: Vadj Vdesired 5.0 V Example: Increase Vdesired = 5.2 V V = V Example: Increase 4% => V o = 5.2 Vdc k = 404 k

12 EDGJKLT PRODUCT SPECIFICATION 5 (6) 2/1301-BMR 673 Technical 02 Uen Specification 12 SEC/D PKU 5500E (Julia You) series DC/DC Converters EXUEFYA B Typical Characteristics 5 V, 10 A / 50 W Output Current Derating, Vin=53V PKU 5511E PI m/s 2.0 m/s 1.5 m/s 1.0 m/s 0.5 m/s Nat. Conv [ C] Available load current vs. ambient air temperature and airflow at V I = 53 V. See Thermal Consideration section. Output Current Derating, Vin=27V m/s 2.0 m/s 1.5 m/s 1.0 m/s 0.5 m/s Nat. Conv [ C] Available load current vs. ambient air temperature and airflow at V I = 27 V. See Thermal Consideration section.

13 BURAERHBA (ESXICEN) PRODUCT SPECIFICATION 2 (6) 2/1301-BMR Uen Technical Specification 13 BURAERHBA (Lisa Li) EXUEFYA B Electrical Specification 12 V, 4.2 A / 50 W PKU 5513E PI T P1 = -40 to +90ºC, V I = 18 to 75 V, unless otherw ise specified under Conditions. Typical values given at: T P1 = +25 C, V I= 53 V I max I O, unless otherw ise specified under Conditions. Additional C in = 100 µf. C out = 470 µf Characteristics Conditions min typ max Unit V I Input voltage range V V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 6.6 μf P O Output pow er 0 50 W η Efficiency 50% of max I O, V i=27v 91.7 max I O, V i=27v % of max I O, V I = 53 V 86 max I O, V I = 53 V 89.3 P d Pow er Dissipation max I O W P li Input idling pow er I O = 0 A, V I = 53 V 2.6 W P RC Input standby pow er V I = 53 V (turned off with RC) 0.44 W f s Sw itching frequency % of max I O khz % V Oi V O Output voltage initial setting and accuracy T P1 = +25 C, V I = 53 V, I O = 4.2 A V Output adjust range See operating information V Output voltage tolerance band % of max I O V Idling voltage I O = 0 A V Line regulation max I O ±5 ±15 mv Load regulation V I = 53 V, 0-100% of max I O ±10 ±20 mv Load transient V tr V I = 53 V, Load step % of ±350 ±520 mv voltage deviation max I O, di/dt = 1 A/μs t tr Load transient recovery time see Note µs t r t s t f t RC RC Ramp-up time ms (f rom 10 90% of V Oi) % of max I O Start-up time (f rom V I connection to 90% of V Oi) ms V I shut-down fall time (f rom V I of f to 10% of V O) RC start-up time (f rom V RC connection to 90% of V Oi) RC shut-dow n fall time (f rom RC of f to 10% of V O) max I O 7 ms I O = 0 A 8.5 s max I O 420 ms max I O 3.5 ms I O = 0 A 7.5 s Sink current, see Note 2 See operating information 0.5 ma Trigger level Decreasing / Increasing RC-voltage 1 V I O Output current A I lim Current limit threshold T P1 < max T P A I sc Short circuit current T P1 = 25ºC, see Note A C out Recommended Capacitive Load T P1 = 25ºC µf V Oac Output ripple & noise See ripple & noise section, V Oi mvp-p OVP Over voltage protection T P1 = +25 C, V I = 53 V, 0-100% of max I O V Note 1: 470uF OS-CON cap used at load transient test Note 2: Sink current drawn by external device connected to the RC pin. Minimum sink current required to guarantee activated RC function. Note 3: hiccup mode OCP, RMS value

14 BURAERHBA (ESXICEN) PRODUCT SPECIFICATION 3 (6) 2/1301-BMR Uen Technical Specification 14 BURAERHBA (Lisa Li) EXUEFYA B Typical Characteristics 12 V, 4.2 A / 50 W Efficiency Power Dissipation PKU 5513E PI [%] 95 [W] V 27 V 53 V 75 V V 27 V 53 V 75 V Ef f iciency vs. load current and input v oltage at T P1 = +25 C. Dissipated power v s. load current and input v oltage at T P1 = +25 C. Output Characteristics Current Limit Characteristics [V] [V] V 27 V 53 V 75 V V 27 V 53 V 75 V Output v oltage v s. load current at T P1 = +25 C. Output v oltage v s. load current at I O > max I O, T P1 = +25 C.

15 BURAERHBA (ESXICEN) PRODUCT SPECIFICATION 4 (6) 2/1301-BMR Uen Technical Specification 15 BURAERHBA (Lisa Li) EXUEFYA B Typical Characteristics 12 V, 4.2 A / 50 W PKU 5513E PI Start-up Shut-down Start-up enabled by connecting VI at: TP1 = +25 C, VI = 53 V, IO = 4.2 A resistive load. Top trace: output voltage (10 V/div). Bottom trace: input voltage (20 V/div). Time scale: (20 ms/div). Shut-down enabled by disconnecting VI at: TP1 = +25 C, VI = 53 V, IO = 4.2 A resistive load. Top trace: output voltage (10 V/div). Bottom trace: input voltage (20 V/div). Time scale: (50 ms/div). Output Ripple & Noise Output Load Transient Response Output voltage ripple at: TP1 = +25 C, VI = 53 V, IO = 4.2 A resistive load. Trace: output voltage (20 mv/div). Time scale: (1 µs/div.). Output voltage response to load current stepchange ( A) at: TP1 =+25 C, VI = 53 V Top trace: output voltage (500 mv/div). Bottom trace: load current (1 A/div). Time scale: (500 µs /div). Output Voltage Adjust (see operating information) Passive adjust The resistor v alue f or an adjusted output v oltage is calculated by using the f ollowing equations: Output Voltage Adjust, Decrease: = 511 Radj 10. % 22 kω Output Voltage Adjust, Increase: ( % ) 511 Radj = kω % % Active adjust The output v oltage may be adjusted using a v oltage applied to the Vadj pin. This v oltage is calculated by using the f ollowing equation: Vadj Vdesired 12.0 = V 12.0 Example: Increase Vdesired = V V = V 12.0 Example: Increase 4% => V o = Vdc 5.11 ( + 4) kω = 1163 kω 4

16 BURAERHBA (ESXICEN) PRODUCT SPECIFICATION 5 (6) 2/1301-BMR Uen Technical Specification 16 BURAERHBA (Lisa Li) EXUEFYA B Typical Characteristics 12 V, 4.2 A / 50 W PKU 5513E PI Output Current Derating, Vin=27V Output Current Derating, Vin=53V [ C] 3.0 m/s 2.0 m/s 1.5 m/s 1.0 m/s 0.5 m/s Nat. Conv [ C] 3.0 m/s 2.0 m/s 1.5 m/s 1.0 m/s 0.5 m/s Nat. Conv. Av ailable load current v s. ambient air temperature and airf low at V I = 27 V. See Thermal Consideration section. Av ailable load current v s. ambient air temperature and airf low at V I = 53 V. See Thermal Consideration section.

17 EKUNLAN Flex Internal PRODUCT SPECIFICATION 1 (5) 3/1301-BMR 673 Uen Technical Specification 17 BURAEICKA (Lisa Li) EXUEFYA D EMC Specification Conducted EMI measured according to EN55022, CISPR 22 and FCC part 15J (see test set-up). See Design Note 009 for further information. The fundamental switching frequency is 415 khz for PKU 5510E PI, PKU 5511E PI and PKU 5513E at VI = 48 V and max IO. Conducted EMI Input terminal value (typ) Test set-up EMI without filter Optional external filter for class B Suggested external input filter in order to meet class B in EN 55022, CISPR 22 and FCC part 15J. Filter components: C1,2 = 2.2 F (ceramic cap) C3 = 220 F (electrolytic cap) C6 = 100 uf (electrolytic cap) C4,5 = 2.2 nf,2kv (ceramic cap) L1 = 1.32 mh (Pulse P0420) Layout recommendations The radiated EMI performance of the product will depend on the PWB layout and ground layer design. It is also important to consider the stand-off of the product. If a ground layer is used, it should be connected to the output of the product and the equipment ground or chassis. A ground layer will increase the stray capacitance in the PWB and improve the high frequency EMC performance. Output ripple and noise Output ripple and noise measured according to figure below. See Design Note 022 for detailed information. Output ripple and noise test setup EMI with filter

18 EKUNLAN Flex Internal PRODUCT SPECIFICATION 2 (5) 3/1301-BMR 673 Uen Technical Specification 18 BURAEICKA (Lisa Li) EXUEFYA D Operating information Input Voltage The input voltage range 18 to 75 Vdc meets the requirements of the European Telecom Standard ETS for normal input voltage range in 48 and 60 Vdc systems, to V and 50.0 to -72 V respectively. At input voltages exceeding 75 V, the power loss will be higher than at normal input voltage and TP1 must be limited to absolute max +105 C. The absolute maximum continuous input voltage is 80 Vdc. Short duration transient disturbances can occur on the DC distribution and input of the product when a short circuit fault occurs on the equipment side of a protective device (fuse or circuit breaker). The voltage level, duration and energy of the disturbance are dependant on the particular DC distribution network characteristics and can be sufficient to damage the product unless measures are taken to suppress or absorb this energy. The transient voltage can be limited by capacitors and other energy absorbing devices like zener diodes connected across the positive and negative input conductors at a number of strategic points in the distribution network. The end-user must secure that the transient voltage will not exceed the value stated in the Absolute maximum ratings. ETSI TR examines the parameters of DC distribution networks and provides guidelines for controlling the transient and reduce its harmful effect. Turn-off Input Voltage The products monitor the input voltage and will turn on and turn off at predetermined levels. The minimum hysteresis between turn on and turn off input voltage is 1 V. The input voltage supply must have low impedance to prevent the risk of input oscillation, poor supply can also cause shutdown-bouncing. Remote Control (RC) The products are fitted with a remote control function referenced to the primary negative input connection (-In), with negative and positive logic options available. The RC function allows the product to be turned on/off by an external device like a semiconductor or mechanical switch. The RC pin has an internal pull up resistor to +In. The external device must provide a minimum required sink current to guarantee a voltage not higher than maximum voltage on the RC pin (see Electrical characteristics table). When the RC pin is left open, the voltage generated on the RC pin is V. The standard product is provided with negative logic RC and will be off until the RC pin is connected to the -In. To turn off the product the RC pin should be left open, or connected to a voltage higher than 4 V referenced to -In. In situations where it is desired to have the product to power up automatically without the need for control signals or a switch, the RC pin can be wired directly to -In. The second option is positive logic remote control, which can be ordered by adding the suffix P to the end of the part number. When the RC pin is left open, the product starts up automatically when the input voltage is applied. Turn off is achieved by connecting the RC pin to the -In. The product will restart automatically when this connection is opened. See Design Note 021 for detailed information. Input and Output Impedance The impedance of both the input source and the load will interact with the impedance of the DC/DC converter. It is important that the input source has low characteristic impedance. The performance in some applications can be enhanced by addition of external capacitance as described in External Decoupling Capacitors. If the input voltage source contains significant inductance, the addition of a low ESR 100 µf capacitor across the input of the converter will ensure stable operation in all conditions. External Decoupling Capacitors The products have been designed to operate with a minimum capacitance connected to their output. When powering loads with significant dynamic current requirements, the voltage regulation at the point of load can be improved by addition of decoupling capacitors at the load. The most effective technique is to locate low ESR ceramic and electrolytic capacitors as close to the load as possible, using several parallel capacitors to lower the effective ESR. The ceramic capacitors will handle high-frequency dynamic load changes while the electrolytic capacitors are used to handle low frequency dynamic load changes. It is equally important to use low resistance and low inductance PWB layouts and cabling. External decoupling capacitors will become part of the product s control loop. The control loop is optimized for a wide range of external capacitance and the maximum recommended value that could be used without any additional analysis is found in the Electrical specification. Minimum Input Capacitance Minimum Output Capacitance PKU 5510E PI 100uF 470uF PKU 5511E PI 100uF 330uF PKU 5513E PI 100uF 220uF Minimum capacitance

19 EKUNLAN Flex Internal PRODUCT SPECIFICATION 3 (5) 3/1301-BMR 673 Uen Technical Specification 19 BURAEICKA (Lisa Li) EXUEFYA D For further information please contact your local Flex Power Modules representative. Output Voltage Adjust (Vadj) The products have an Output Voltage Adjust pin (Vadj). This pin can be used to adjust the output voltage above or below Output voltage initial setting. When increasing the output voltage, the voltage at the output pins must be kept below the threshold of the over voltage protection, (OVP) to prevent the product from shutting down. At increased output voltages the maximum power rating of the product remains the same, and the max output current must be decreased correspondingly. To increase the voltage the resistor should be connected between the Vadj pin and +out pin. The resistor value of the Output voltage adjust function is according to information given under the Output section for the respective product. To decrease the output voltage, the resistor should be connected between the Vadj pin and out pin. designed for the maximum output short circuit current specified. Pre-bias Start-up PKU 5510E PI and PKU 5513E PI have a Pre-bias start up functionality and will not sink current during start up if a prebias source with less than 75% of Vo is present at the output terminals. PKU 5511E PI has a Pre-bias start up functionality and will not sink current during start up if a pre-bias source with less than 60% of Vo is present at the output terminals. With the ramp up slew rate of input voltage less than 10V/ms, the Prebias capability can be lifted to 75% of Vo. Thermal Consideration General The products are designed to operate in different thermal environments and sufficient cooling must be provided to ensure reliable operation. For products mounted on a PWB without a heat sink attached, cooling is achieved mainly by conduction, from the pins to the host board, and convection, which is dependant on the airflow across the product. Increased airflow enhances the cooling of the product. The Output Current Derating graph found in the Output section for each model provides the available output current vs. ambient air temperature and air velocity at VI = 53 V and 27V. Over Temperature Protection (OTP) The products are protected from thermal overload by an internal over temperature shutdown circuit. When TP1 as defined in thermal consideration section exceeds 115 C the product will shut down. The product will make continuous attempts to start up (non-latching mode) and resume normal operation automatically when the temperature has dropped >10 C below the temperature threshold. The product is tested on a 254 x 254 mm, 35 µm (1 oz), 8-layer test board mounted vertically in a wind tunnel with a cross-section of 608 x 203 mm. Over Voltage Protection (OVP) The products have output over voltage protection that will shut down the product in over voltage conditions. The product will make continuous attempts to start up (non-latching mode) and resume normal operation automatically after removal of the over voltage condition. Over Current Protection (OCP) The products include current limiting circuitry for protection at continuous overload. The output voltage will decrease towards zero for output currents in excess of max output current (max IO). After a time period exceeding 10 ms in OCP converters will enter hiccupmode to reduce average output power. The product will resume normal operation after removal of the overload. The load distribution should be

20 EKUNLAN Flex Internal PRODUCT SPECIFICATION 4 (5) 3/1301-BMR 673 Uen Technical Specification 20 BURAEICKA (Lisa Li) EXUEFYA D Definition of product operating temperature The product operating temperatures is used to monitor the temperature of the product, and proper thermal conditions can be verified by measuring the temperature at positions P1. The temperature at position TP1 should not exceed the maximum temperatures in the table below. The number of measurement points may vary with different thermal design and topology. Temperatures above maximum TP1, measured at the reference point P1 are not allowed and may cause permanent damage. Connections Position Description Max Temp. P1 Opto coupler T P1=105ºC Pin Designation Function 1 +In Positive Input 2 RC Remote control 3 -In Negative Input 4 -Out Negative Output 6 Vadj Output voltage adjust 8 +Out Positive Output Open frame

21 EPEIHLI PRODUCT SPEC. MECHANICAL 1 (3) 4/1301-BMR 673 Technical Uen Specification 21 SEC/D PKU 5500E (Julia You) series DC/DC Converters See B Mechanical Information - Hole Mount, Open Frame Version All component placements whether shown as physical components or symbolical outline are for reference only and are subject to change throughout the product s life cycle, unless explicitly described and dimensioned in this drawing.

22 EPEIHLI PRODUCT SPEC. MECHANICAL 2 (3) 4/1301-BMR 673 Technical Uen Specification 22 SEC/D PKU 5500E (Julia You) series DC/DC Converters See B Mechanical Information - Surface Mount Version All component placements whether shown as physical components or symbolical outline are for reference only and are subject to change throughout the product s life cycle, unless explicitly described and dimensioned in this drawing.

23 EPEIHLI PRODUCT SPEC. 1 (4) 5/1301-BMR 673 Uen Technical Specification 23 SEC/D (Julia You) See B Template rev. J Soldering Information - Surface Mounting and Hole Mount through Pin in Paste Assembly The surface mount product is intended for forced convection or vapor phase reflow soldering in SnPb or Pb-free processes. The reflow profile should be optimised to avoid excessive heating of the product. It is recommended to have a sufficiently extended preheat time to ensure an even temperature across the host PWB and it is also recommended to minimize the time in reflow. A no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board, since cleaning residues may affect long time reliability and isolation voltage. General ref low process specif ications SnPb eutectic Pb-f ree Av erage ramp-up (T PRODUCT) 3 C/s max 3 C/s max Ty pical solder melting (liquidus) temperature TL 183 C 221 C Minimum ref low time abov e TL 60 s 60 s Minimum pin temperature TPIN 210 C 235 C Peak product temperature TPRODUCT 225 C 260 C Av erage ramp-down (T PRODUCT) 6 C/s max 6 C/s max Maximum time 25 C to peak 6 minutes 8 minutes Lead-free (Pb-free) solder processes For Pb-free solder processes, a pin temperature (TPIN) in excess of the solder melting temperature (TL, 217 to 221 C for SnAgCu solder alloys) for more than 60 seconds and a peak temperature of 245 C on all solder joints is recommended to ensure a reliable solder joint. Maximum Product Temperature Requirements Top of the product PWB near pin 2 is chosen as reference location for the maximum (peak) allowed product temperature (TPRODUCT) since this will likely be the warmest part of the product during the reflow process. SnPb solder processes For SnPb solder processes, the product is qualified for MSL 1 according to IPC/JEDEC standard J-STD-020C. During reflow TPRODUCT must not exceed 225 C at any time. Pb-free solder processes For Pb-free solder processes, the product is qualified for MSL 3 according to IPC/JEDEC standard J-STD-020C. During reflow TPRODUCT must not exceed 260 C at any time. Temperature T L T PRODUCT maximum T PIN minimum Pin profile Dry Pack Information Products intended for Pb-free reflow soldering processes are delivered in standard moisture barrier bags according to IPC/JEDEC standard J-STD-033 (Handling, packing, shipping and use of moisture/reflow sensitivity surface mount devices). Time in preheat / soak zone Time 25 C to peak Time in reflow Product profile Time Minimum Pin Temperature Recommendations Pin number 8 is chosen as reference location for the minimum pin temperature recommendation since this will likely be the coolest solder joint during the reflow process. Using products in high temperature Pb-free soldering processes requires dry pack storage and handling. In case the products have been stored in an uncontrolled environment and no longer can be considered dry, the modules must be baked according to J-STD-033. Thermocoupler Attachment Pin 8 for measurement of minimum pin temperature (solder joint) temperature, T PIN SnPb solder processes For SnPb solder processes, a pin temperature (TPIN) in excess of the solder melting temperature, (TL, 183 C for Sn63Pb37) for more than 60 seconds and a peak temperature of 220 C is recommended to ensure a reliable solder joint. For dry packed products only: depending on the type of solder paste and flux system used on the host board, up to a recommended maximum temperature of 245 C could be used, if the products are kept in a controlled environment (dry pack handling and storage) prior to assembly. Pin 2 for measurement of maximum product temperature, T PRODUCT

24 EPEIHLI PRODUCT SPEC. 2 (4) 5/1301-BMR 673 Uen Technical Specification 24 SEC/D (Julia You) See B Template rev. J Soldering Information - Hole Mounting The hole mounted product is intended for plated through hole mounting by wave or manual soldering. The pin temperature is specified to maximum to 270 C for maximum 10 seconds. A maximum preheat rate of 4 C/s and maximum preheat temperature of 150 C is suggested. When soldering by hand, care should be taken to avoid direct contact between the hot soldering iron tip and the pins for more than a few seconds in order to prevent overheating. Tray Specifications Material Antistatic PPE Surface resistance 10 5 < Ohm/square < Bakability The trays can be baked at maximum [125 C f or 48 hours] Tray thickness 18.5 mm [0.728 inch] Box capacity 150 products (5 full trays/box) Tray w eight 190 g empty, 620 g full tray A no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board. The cleaning residues may affect long time reliability and isolation voltage. Delivery Package Information The surface mounted products are delivered in antistatic injection molded trays (Jedec design guide 4.10D standard) or in antistatic carrier tape (EIA 481 standard). The through-hole mounted products are delivered in antistatic injection molded trays (Jedec design guide 4.10D standard). Carrier Tape Specifications Material Antistatic PS Surface resistance 10 5 < Ohm/square < Bakeability The tape is not bakable Tape width, W Pocket pitch, P 1 Pocket depth, K 0 Reel diameter Reel capacity Reel weight 56 mm [2.2 inch] 36 mm [1.42 inch] 9.7 mm [0.382 inch] 380 mm [15 inch] 170 products /reel Rounded 2.5 kg/full reel EIA standard carrier tape Side view User tape feed direction Top view Pocket depth, K 0 Round holes Tape width, W Pocket pitch, P 1 Elongated holes Pin 1 X= Vacuum pickup area All dimensions in mm [inch] Tolerances: X.xx mm ±0.13 mm [0.005], X.x mm ±0.26 mm [0.01] Note: Tray dimensions refer to pocket center. For exact location of product pick up surface, refer to mechanical drawing.

25 EPEIHLI PRODUCT SPEC. 3 (4) 5/1301-BMR 673 Uen SEC/D (Julia You) See B Template rev. J Product Qualification Specification Characteristics External visual inspection Change of temperature (Temperature cycling) Cold (in operation) Damp heat Dry heat Electrostatic discharge susceptibility IPC-A-610 IEC Na IEC Ad IEC Cy IEC Bd IEC , JESD 22-A114 IEC , JESD 22-A115 Immersion in cleaning solvents IEC XA, method 2 Mechanical shock Moisture reflow sensitivity 1 IEC Ea J-STD-020C Temperature range Number of cycles Dw ell/transfer time Temperature T A Duration Temperature Humidity Duration Temperature Duration Human body model (HBM) Machine Model (MM) Water Glycol ether Isopropyl alcohol Peak acceleration Duration Level 1 (SnPb-eutectic) Level 3 (Pb Free) Operational life test MIL-STD-202G, method 108A Duration 1000 h Resistance to soldering heat 2 Robustness of terminations Solderability IEC Tb, method 1A IEC Test Ua1 IEC Test Ue1 IEC test Td 1 Solder temperature Duration Through hole mount products Surface mount products Preconditioning Temperature, SnPb Eutectic Temperature, Pb-free IEC test Ta 2 Preconditioning Temperature, SnPb Eutectic Temperature, Pb-free Frequency Vibration, broad band random IEC Fh, method 1 Spectral density Duration Notes 1 Only for products intended for reflow soldering (surface mount products) 2 Only for products intended for wave soldering (plated through hole products) Technical Specification to 100 C min/0-1 min -45 C 72 h 85 C 85 % RH 1000 hours 125 C 1000 h Class 2, 2000 V Class 3, 200 V 55 C 35 C 35 C 100 g 6 ms 225 C 260 C 270 C s All leads All leads 150 C dry bake 16 h 215 C 235 C Steam ageing 235 C 245 C 10 to 500 Hz 0.07 g 2 /Hz 10 min in each direction