Key Features. General Characteristics. Ericsson Limited Internal. Contents

Size: px
Start display at page:

Download "Key Features. General Characteristics. Ericsson Limited Internal. Contents"

Transcription

1 Ericsson PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (3) MPM/BY/P Henrik Sundh 1/ EN/LZT BMR 642 Technical 8 Uen Specification MPM/BY/M PME 8000 [Krister series Lundberg] PoL Regulators A Key Features 6A output current V input voltage range Output voltages from 0.8V up to 5.5V Industry standard POLA compatible 22.1 x x 8.51 mm (0.87 x 0.5 x in.) High efficiency, up to. 94% Auto Track sequencing pin More than 4.4 million hours MTBF General Characteristics Operating temperature: -40ºC to 85ºC Input under voltage protection Start up into a pre-biased output safe Output short-circuit protection On/Off inhibit control Wide output voltage adjust function Highly automated manufacturing ensures quality ISO 9001/14001 certified supplier Safety Approvals Design for Environment Meets requirements in hightemperature lead-free soldering processes. Contents General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Product Program Ordering V/6 A PME 8118T V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification V/6 A PME 8318L V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification V/6 A Electrical Specification EMC Specification Operating Information Thermal Consideration Connections Mechanical Information Soldering Information Delivery Information Product Qualification Specification... 47

2 MPM/BY/P Henrik Sundh Ericsson Internal PRODUCT SPECIFICATION 2 (3) 1/1301 BMR 642 Technical 8 Uen Specification 2 MPM/BY/M PME 8000 [Krister series Lundberg] PoL Regulators A General Information Ordering Information See Contents for individual product ordering numbers. Option Through hole pin SMD pin SMD pin, leadfree reflow temperature capable Reliability Suffix P S R PME8118TP PME8118TS PME8118TSR The Mean Time Between Failure (MTBF) is calculated at full output power and an operating ambient temperature (T A ) of +40 C. Different methods could be used to calculate the predicted MTBF and failure rate which may give different results. Flex currently uses Telcordia SR332. Predicted MTBF for the series is: million hours according to Telcordia SR332, issue 1, Black box technique. Telcordia SR332 is a commonly used standard method intended for reliability calculations in IT&T equipment. The parts count procedure used in this method was originally modelled on the methods from MIL-HDBK-217F, Reliability Predictions of Electronic Equipment. It assumes that no reliability data is available on the actual units and devices for which the predictions are to be made, i.e. all predictions are based on generic reliability parameters. Quality Statement The products are designed and manufactured in an industrial environment where quality systems and methods like ISO 9000, 6σ (sigma), and SPC are intensively in use to boost the continuous improvements strategy. Infant mortality or early failures in the products are screened out and they are subjected to an ATE-based final test. Conservative design rules, design reviews and product qualifications, plus the high competence of an engaged work force, contribute to the high quality of our products. Warranty Warranty period and conditions are defined in Flex General Terms and Conditions of Sale. Limitation of Liability Flex does not make any other warranties, expressed or implied including any warranty of merchantability or fitness for a particular purpose (including, but not limited to, use in life support applications, where malfunctions of product can cause injury to a person s health or life). Flex 2017 The information and specifications in this technical specification is believed to be correct at the time of publication. However, no liability is accepted for inaccuracies, printing errors or for any consequences thereof. Flex reserves the right to change the contents of this technical specification at any time without prior notice. Compatibility with RoHS requirements The products are compatible with the relevant clauses and requirements of the RoHS directive 2011/65/EU and have a maximum concentration value of 0.1% by weight in homogeneous materials for lead, mercury, hexavalent chromium, PBB and PBDE and of 0.01% by weight in homogeneous materials for cadmium. Exemptions in the RoHS directive utilized in Flex products are found in the Statement of Compliance document. Flex fulfills and will continuously fulfill all its obligations under regulation (EC) No 1907/2006 concerning the registration, evaluation, authorization and restriction of chemicals (REACH) as they enter into force and is through product materials declarations preparing for the obligations to communicate information on substances in the products.

3 MPM/BY/P Henrik Sundh Ericsson Internal PRODUCT SPECIFICATION 3 (3) 1/1301 BMR 642 Technical 8 Uen Specification 3 MPM/BY/M PME 8000 [Krister series Lundberg] PoL Regulators A Safety Specification General information Flex DC/DC converters and DC/DC regulators are designed in accordance with safety standards IEC/EN/ UL60950, Safety of Information Technology Equipment. IEC/EN/UL60950 contains requirements to prevent injury or damage due to the following hazards: Electrical shock Energy hazards Fire Mechanical and heat hazards Radiation hazards Chemical hazards On-board DC-DC converters are defined as component power supplies. As components they cannot fully comply with the provisions of any Safety requirements without Conditions of Acceptability. It is the responsibility of the installer to ensure that the final product housing these components complies with the requirements of all applicable Safety standards and Directives for the final product. Component power supplies for general use should comply with the requirements in IEC60950, EN60950 and UL60950 Safety of information technology equipment. There are other more product related standards, e.g. IEEE802.3af Ethernet LAN/MAN Data terminal equipment power, and ETS Power supply interface at the input to telecommunications equipment; part 2: DC, but all of these standards are based on IEC/EN/UL60950 with regards to safety. Flex DC/DC converters and DC/DC regulators are UL60950 recognized and certified in accordance with EN The flammability rating for all construction parts of the products meets requirements for V-0 class material according to IEC The products should be installed in the end-use equipment, in accordance with the requirements of the ultimate application. Normally the output of the DC/DC converter is considered as SELV (Safety Extra Low Voltage) and the input source must be isolated by minimum Double or Reinforced Insulation from the primary circuit (AC mains) in accordance with IEC/EN/UL Isolated DC/DC converters It is recommended that a slow blow fuse with a rating twice the maximum input current per selected product be used at the input of each DC/DC converter. If an input filter is used in the circuit the fuse should be placed in front of the input filter. In the rare event of a component problem in the input filter or in the DC/DC converter that imposes a short circuit on the input source, this fuse will provide the following functions: Isolate the faulty DC/DC converter from the input power source so as not to affect the operation of other parts of the system. Protect the distribution wiring from excessive current and power loss thus preventing hazardous overheating. The galvanic isolation is verified in an electric strength test. The test voltage (V iso ) between input and output is 1500 Vdc or 2250 Vdc for 60 seconds (refer to product specification). Leakage current is less than 1 μa at nominal input voltage. 24 V DC systems The input voltage to the DC/DC converter is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions. 48 and 60 V DC systems If the input voltage to Flex DC/DC converter is 75 Vdc or less, then the output remains SELV (Safety Extra Low Voltage) under normal and abnormal operating conditions. Single fault testing in the input power supply circuit should be performed with the DC/DC converter connected to demonstrate that the input voltage does not exceed 75 Vdc. If the input power source circuit is a DC power system, the source may be treated as a TNV2 circuit and testing has demonstrated compliance with SELV limits and isolation requirements equivalent to Basic Insulation in accordance with IEC/EN/UL Non-isolated DC/DC regulators The input voltage to the DC/DC regulator is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions.

4 PRODUCT SPEC. 1 (34) 2/1301-BMR 642 Technical 8 Uen Specification 4 SEC/D PME 8000 Wei Zhang series A PoL Regulators A Absolute Maximum Ratings Characteristics min typ max Unit T ref Operating Temperature (see Thermal Consideration section) C T S Storage temperature C V I Input voltage V inh Inhibit On/Off pin voltage Positive logic option V in -0.5 Open V (see Operating Information section) Negative logic option N/A N/A V V adj Adjust pin voltage (see Operating Information section) N/A N/A V Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits of Output data or Electrical Characteristics. If exposed to stress above these limits, function and performance may degrade in an unspecified manner. Fundamental Circuit Diagram +IN OUT GND Auto Track TRK PWM Controller Error Amplifier ADJ Ref INH RC Block GND GND GND

5 PRODUCT SPEC. 2 (34) 2/1301-BMR 642 Technical 8 Uen Specification 5 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 0.8 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = open, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power W η Efficiency 50 % of max I O 81.0 max I O 79.7 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 260 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.5 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±70 mv see Note 1 40 µs max I O 0.6 ms 12.9 ms t f Max I o 2.6 ms (From V I off to 10% of V O ) I o = 1A 14.7 ms INHIBIT start-up time Max I o 12.5 ms t Inh INHIBIT shutdown fall time Max I o 20 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 0.8 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section

6 PRODUCT SPEC. 3 (34) 2/1301-BMR 642 Technical 8 Uen Specification 6 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 0.8 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] [ C] 0.70 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

7 PRODUCT SPEC. E 4 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 0.8 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 7 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 2.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

8 PRODUCT SPEC. 5 (34) 2/1301-BMR 642 Technical 8 Uen Specification 8 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.0 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 32.4 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power 0 6 W η Efficiency 50 % of max I O 83.4 max I O 82.7 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 300 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.6 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±75 mv see Note 1 50 µs max I O 0.8 ms 13.1 ms t f Max I o 2.2 ms (From V I off to 10% of V O ) I o = 1A 12.1 ms INHIBIT start-up time Max I o 12.7 ms t Inh INHIBIT shutdown fall time Max I o 20 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.3 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section

9 PRODUCT SPEC. 6 (34) 2/1301-BMR 642 Technical 8 Uen Specification 9 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.0 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] [ C] 0.90 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

10 PRODUCT SPEC. E 7 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.0 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 10 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

11 PRODUCT SPEC. 8 (34) 2/1301-BMR 642 Technical 8 Uen Specification 11 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.2 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 12.1 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =560uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power W η Efficiency 50 % of max I O 85.0 max I O 84.7 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 350 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.7 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±75 mv see Note 1 40 µs max I O 1.1 ms 13.5 ms t f Max I o 1.9 ms (From V I off to 10% of V O ) I o = 1A 10.2 ms INHIBIT start-up time Max I o 13.0 ms t Inh INHIBIT shutdown fall time Max I o 30 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.5 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section

12 PRODUCT SPEC. 9 (34) 2/1301-BMR 642 Technical 8 Uen Specification 12 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.2 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] [ C] 1.10 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

13 PRODUCT SPEC. E 10 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.2 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 13 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

14 PRODUCT SPEC. 11 (34) 2/1301-BMR 642 Technical 8 Uen Specification 14 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.5 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 3.57 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power 0 9 W η Efficiency 50 % of max I O 86.3 max I O 87.0 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 430 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.9 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±75 mv see Note 1 40 µs max I O 1.4 ms 13.7 ms t f Max I o 1.6 ms (From V I off to 10% of V O ) I o = 1A 8.3 ms INHIBIT start-up time Max I o 13.4 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.9 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section

15 PRODUCT SPEC. 12 (34) 2/1301-BMR 642 Technical 8 Uen Specification 15 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.5 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] [ C] 1.40 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

16 PRODUCT SPEC. E 13 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.5 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 16 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

17 PRODUCT SPEC. 14 (34) 2/1301-BMR 642 Technical 8 Uen Specification 17 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.8 V/6 A Electrical Specification PME 8118T T ref = -40 to +85ºC, V I = 10.8 to, R adj = 130 Ω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =560uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power W η Efficiency 50 % of max I O 87.3 max I O 88.1 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 520 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.0 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 40 µs max I O 1.7 ms 14.3 ms t f Max I o 1.3 ms (From V I off to 10% of V O ) I o = 1A 7.0 ms INHIBIT start-up time Max I o 14.1 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 2.0 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 1.0; 20 max I O, V Oi V O >1.0; 30 mvp-p Note 1: Output filter according to Ripple & Noise section

18 PRODUCT SPEC. 15 (34) 2/1301-BMR 642 Technical 8 Uen Specification 18 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.8 V/6 A Typical Characteristics PME 8118T Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] m/s 1.0 m/s 0.5 m/s Nat. Conv. [V] [ C] 1.70 Available load current vs. ambient air temperature and airflow at V I =, V OUT = 1.8 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

19 PRODUCT SPEC. E 16 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.8 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8118T Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 19 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (2 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

20 PRODUCT SPEC. 17 (34) 2/1301-BMR 642 Technical 8 Uen Specification 20 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.2 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = open, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power W η Efficiency 50 % of max I O 83.9 max I O 83.8 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 360 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.7 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 30 µs max I O 1.3 ms 13.3 ms t f Max I o 1.9 ms (From V I off to 10% of V O ) I o = 1A 10.1 ms INHIBIT start-up time Max I o 12.7 ms t Inh INHIBIT shutdown fall time Max I o 30 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.5 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section

21 PRODUCT SPEC. 18 (34) 2/1301-BMR 642 Technical 8 Uen Specification 21 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.2 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] m/s m/s 0.5 m/s [ C] Nat. Conv Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

22 PRODUCT SPEC. E 19 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.2 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 22 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

23 PRODUCT SPEC. 20 (34) 2/1301-BMR 642 Technical 8 Uen Specification 23 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.5 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 24.3 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power 0 9 W η Efficiency 50 % of max I O 85.7 max I O 86.1 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 430 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 0.9 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 30 µs max I O 1.5 ms 13.6 ms t f Max I o 1.5 ms (From V I off to 10% of V O ) I o = 1A 8.4 ms INHIBIT start-up time Max I o 13.0 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 1.9 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section

24 PRODUCT SPEC. 21 (34) 2/1301-BMR 642 Technical 8 Uen Specification 24 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.5 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating Output Characteristics [A] 8 [V] m/s 1.0 m/s 0.5 m/s [ C] Nat. Conv Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

25 PRODUCT SPEC. E 22 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.5 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 20 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 25 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

26 PRODUCT SPEC. 23 (34) 2/1301-BMR 642 Technical 8 Uen Specification 26 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.8 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 11.5 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power W η Efficiency 50 % of max I O 86.7 max I O 87.5 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 500 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.0 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 20 µs max I O 1.7 ms 14.0 ms t f Max I o 1.3 ms (From V I off to 10% of V O ) I o = 1A 7.2 ms INHIBIT start-up time Max I o 13.3 ms t Inh INHIBIT shutdown fall time Max I o 40 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 2.3 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section

27 PRODUCT SPEC. 24 (34) 2/1301-BMR 642 Technical 8 Uen Specification 27 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 1.8 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] m/s 1.0 m/s 0.5 m/s [ C] Nat. Conv Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

28 PRODUCT SPEC. E 25 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 1.8 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 28 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 5.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

29 PRODUCT SPEC. 26 (34) 2/1301-BMR 642 Technical 8 Uen Specification 29 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 2.5 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 4.32 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power 0 15 W η Efficiency 50 % of max I O 88.8 max I O 89.9 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 630 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.5 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 20 µs max I O 2.5 ms 15.0 ms t f Max I o 1.0 ms (From V I off to 10% of V O ) I o = 1A 5.4 ms INHIBIT start-up time Max I o 14.3 ms t Inh INHIBIT shutdown fall time Max I o 60 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 3.0 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section

30 PRODUCT SPEC. 27 (34) 2/1301-BMR 642 Technical 8 Uen Specification 30 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 2.5 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] m/s 1.0 m/s 0.5 m/s [ C] Nat. Conv Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

31 PRODUCT SPEC. E 28 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 2.5 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 31 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 2.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

32 PRODUCT SPEC. 29 (34) 2/1301-BMR 642 Technical 8 Uen Specification 32 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 3.3 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 2.00 kω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power W η Efficiency 50 % of max I O 89.2 max I O 90.7 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 860 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 1.8 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±80 mv see Note 1 10 µs max I O 3.5 ms 16.0 ms t f Max I o 0.8 ms (From V I off to 10% of V O ) I o = 1A 4.3 ms INHIBIT start-up time Max I o 15.5 ms t Inh INHIBIT shutdown fall time Max I o 80 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 4.0 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section

33 PRODUCT SPEC. 30 (34) 2/1301-BMR 642 Technical 8 Uen Specification 33 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 3.3 V/6 A Typical Characteristics PME 8318L Efficiency Power Dissipation [%] 100 [W] Efficiency vs. load current and input voltage at T ref = +25 C Dissipated power vs. load current and input voltage at T ref = +25 C Output Current Derating [A] 8 Output Characteristics [V] m/s 1.0 m/s 0.5 m/s [ C] Nat. Conv Available load current vs. ambient air temperature and airflow at V I =, V OUT = 3.3 V. See Thermal Consideration section. Output voltage vs. load current at T ref = +25 C

34 PRODUCT SPEC. E 31 (34) Approved series PME 8000 series SEC/D Wei Zhang A PoL Regulators Checked 2/1301-BMR 642Technical 8 Uen Specification Specification Date V, Output up tov, A / 33 W Inputregulator, A/33 POL Input V,6Output Output A/33 W W Rev Reference 3/28701BMR 642 Rev.A November 2017 EN/LZT 146 R1B March R1A February 2006 A Flex Ericsson Ericsson AB Power Modules AB 3.3 V/6 A Typical Characteristics Start-up Start-up enabled by connecting VI at: VI =. PME 8318L Shut-down Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 10 ms/div. Output Ripple & Noise Output voltage ripple (20mV/div.) at: VI =. Time scale: 2 µs/div. 34 Shut-down enabled by disconnecting VI at: VI =. Top trace: output voltage (1.0 V/div.). Bottom trace: input voltage (5 V/div.). Time scale: 2.0 ms/div. Output Load Transient Response See the filter in the Output ripple and noise section (EMC Specification). Output voltage response to load current step- Top trace: output voltage (100mV/div.). change (3-6-3 A) at: Bottom trace: load current (10 A/div.). Tref =+25 C, VI =. Time scale: 0.1 ms/div.

35 PRODUCT SPEC. 32 (34) 2/1301-BMR 642 Technical 8 Uen Specification 35 SEC/D PME 8000 Wei Zhang series A PoL Regulators A 5.0 V/6 A Electrical Specification PME 8318L T ref = -40 to +85ºC, V I = 10.8 to, R adj = 280 Ω, unless otherwise specified under Conditions. Typical values given at: T ref = +25 C, V I =, max I O, unless otherwise specified under Conditions. Additional C in =100uF and C out =330uF. See Operating Information section for selection of capacitor types. Connect the sense pin, where available, to the output pin. Characteristics Conditions min typ max Unit V I Input voltage range 10.8 V Ioff Turn-off input voltage Decreasing input voltage V V Ion Turn-on input voltage Increasing input voltage V C I Internal input capacitance 20 µf P O Output power 0 30 W η Efficiency 50 % of max I O 91.2 max I O 93.1 % P d Power Dissipation max I O W P li Input idling power I O = 0, V I = 1200 mw P RC Input standby power V I = (turned off with INHIBIT) 120 mw I S Static Input current V I =, max I O 2.7 A f s Switching frequency 0-100% of max I O khz V Oi V O V tr t tr t r t s Output voltage initial setting and accuracy T ref = +25 C, V I =, max I O V Output voltage tolerance band % of max I O V Idling voltage I O = V Line regulation max I O ±5 mv Load regulation V I =, 0-100% of max I O ±5 mv Load transient voltage deviation Load transient recovery time Ramp-up time (from % of V Oi ) Start-up time (from V I connection to 90% of V Oi ) Vin shutdown fall time. V I =, Load step % of max I O, di/dt = 1 A/µs, ±90 mv see Note 1 10 µs max I O 6.0 ms 18.3 ms t f Max I o 0.6 ms (From V I off to 10% of V O ) I o = 1A 3.4 ms INHIBIT start-up time Max I o 18.2 ms t Inh INHIBIT shutdown fall time Max I o 120 µs (From INHIBIT off to 10% of V O ) I o = 0.1 A 6.2 ms I O Output current 0 6 A I lim Current limit threshold T ref < max T ref, 14 A V Oac Output ripple & noise See ripple & noise section, V O 2.5; 25 mvp-p max I O, V Oi V O >2.5; 1 % V O Note 1: Output filter according to Ripple & Noise section

Ericsson Internal. General Information Safety Specification Absolute Maximum Ratings

Ericsson Internal. General Information Safety Specification Absolute Maximum Ratings E Ericsson Internal PRODUCT TLE OF CONTENTS SPECIFICATION Prepared (also subject responsible if other) EWEIXIE Approved PMP PMP 5000 303 VHULHV 5000 series PoL Regulators Regulator SEC/D (Julia series

More information

SEC/D PKU 4000 (Julia series You) Direct Converters

SEC/D PKU 4000 (Julia series You) Direct Converters PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (4) EZIWSON 1/1301-BMR 001 52-EN/LZT 602146 Technical Uen 308 Uen Specification SEC/D PKU 4000 (Julia series You) Direct Converters 2011-08-31 2011-03-30 H

More information

Input V, Output up to 39 A / 468 W

Input V, Output up to 39 A / 468 W Prepared (also subject responsible if other) SEC/S EZHIXZH Kevin Zhou Ericsson Internal PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (2) () No. 1/131-12-FGC111823 BMR 46 Technical Uen Specification Approved

More information

36-75 Vdc DC/DC converter Output up to 30 A/90 W

36-75 Vdc DC/DC converter Output up to 30 A/90 W PKB 4000 Series 36-75 Vdc DC/DC converter Output up to 30 A/90 W Contents Product Program...................... 2 Mechanical Information................ 3 Absolute Maximum Ratings............. 4 Input...............................

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Marshall SEC/S Marshall Wang Wang Flex Ericsson internal Internal PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (4) (1) 1 52-EN/LZT 146 439 Uen Approved Checked Date Rev Reference 217-11-23 211-3-29 A PA1

More information

DC/DC regulator Input V Output 16 A

DC/DC regulator Input V Output 16 A PMB 4518T WP Contents Product Program...................... 2 Mechanical Data...................... 2 Connections......................... 2 Absolute Maximum Ratings............. 3 Input...............................

More information

PRODUCT Ericsson Internal SPECIFICATION 1 (5) Ericsson Internal

PRODUCT Ericsson Internal SPECIFICATION 1 (5) Ericsson Internal Ericsson Internal PRODUCT Ericsson Internal SPECIFICATION 1 (5) TABLE OF CONTENTS 1 (2) EAB/FAC/P Prepared (also subject ECHAWAL responsible if other) 1/131- BMR 454 Uen Approved Checked Date Rev Reference

More information

Ericsson Limited Internal

Ericsson Limited Internal Ericsson PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (3) Henrik MPM/BY/P Sundh Henrik (MPM/BY/P) Sundh 1/1301 00152-EN/LZT146320 BMR 644 Technical 5 Uen Specification MPM/BY/M PMG 5000 [Krister series

More information

Key Features. General Characteristics. Ericsson Limited Internal. Contents

Key Features. General Characteristics. Ericsson Limited Internal. Contents Ericsson PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (3) Henrik MPM/BY/P Sundh Henrik (MPM/BY/P) Sundh 1/1301 00152-EN/LZT146325 BMR 646 Technical 4 Uen Specification MPM/BY/M PMJ 4000 [Krister series

More information

DC/DC regulator Input V Output 16 A

DC/DC regulator Input V Output 16 A PMB 8818T P Contents Product Program...................... 2 Mechanical Data...................... 2 Connections......................... 2 Absolute Maximum Ratings............. 3 Input...............................

More information

36-75 Vdc DC/DC converter Output up to 20 A/50 W

36-75 Vdc DC/DC converter Output up to 20 A/50 W PKM 4000E Series 36-75 Vdc DC/DC converter Output up to 20 A/50 W Contents Product Program...................... 2 Quality Statement..................... 2 Limitation of Liability................... 2

More information

DC/DC regulator Input V Output 10 A

DC/DC regulator Input V Output 10 A PMB 8518T P Contents Product Program...................... 2 Mechanical Data...................... 2 Connections......................... 2 Absolute Maximum Ratings............. 3 Input...............................

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 UMEC/Woody Lin 1/1301-BM 711 Ericsson Internal PODUCT SPECIFICATION 1 (4) Key Features Industry standard case dimensions 57.91 x 36.8 x 12.7 mm (2.28 x 1.45 x 0.5 in) High efficiency, typ. 89% at 24 Vout

More information

DC/DC converters, Input V, Output up to 35 A/132 W Ericsson AB

DC/DC converters, Input V, Output up to 35 A/132 W Ericsson AB PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (4) EZHIXZH 001 1/1301-BMR 52-EN/LZT 637146 Technical 02416 Uen Uen Specification SEC/D PKM 4000D (Betty Wu) PINB series 2010-01-21 2010-02-02 D J Key Features

More information

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Prepared Prepared (also (also subject subject responsible if if other) other) EAB/FAC/P EYIZJIA Susanne Eriksson Ericsson Internal TABLE PRODUCT OF CONTENTS SPECIFICATION 1 (1) (4) No. No. BPOW 1/1301-BMR

More information

DC/DC power module 3.3V / 4.5A / 14.8W

DC/DC power module 3.3V / 4.5A / 14.8W PKF 4110B I DC/DC power module 3.3V / 4.5A / 14.8W SMD package with ultra low component height 8.0 mm (0.315 in.) 84% efficiency at full load 1,500 Vdc isolation voltage Synchronous rectification MTTF

More information

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 SEC/S EAB/FAC/P Gavin Susanne Du Eriksson PRODUCT TABLE OF CONTENTS SPECIFICATION 12 (4) (3) BPOW 1/131-BMR 21-152 463 Uen Uen EAB/FAC/P [Susanne Eriksson] 214-1-3 29-7-1 EN/LZT 146 434 R4B February 214

More information

Technical Specification

Technical Specification Prepared (Subject resp) jidgjian Grace Jiang INTERNAL USE ONLY PRODUCT SPECIFICATION 1 (4) No. 1/1301-BMR7128413 Approved (Document resp) Checked Date Rev PKE 8000A series Direct Converters Key Features

More information

DC/DC power module 1.8 V / 5A / 9W

DC/DC power module 1.8 V / 5A / 9W PKF 4918 B I DC/DC power module 1.8 V / 5A / 9W SMD package with ultra low component height 8.0 mm (0.315 in.) 80% efficiency at full load 1,500 Vdc isolation voltage Synchronous rectification MTTF >10

More information

Ericsson Internal. Contents. Optional baseplate ISO 9001/14001 certified supplier PMBus Revision 1.1 compliant

Ericsson Internal. Contents. Optional baseplate ISO 9001/14001 certified supplier PMBus Revision 1.1 compliant Prepared (also subject responsible if other) Prepared (also subject responsible if other) EZHIXZH SEC/S Kevin Zhou Ericsson Internal TABLE PRODUCT OF CONTENTS SPECIFICATION 1 (1) 1 (5) No. No. 1/131- BMR

More information

General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 JIDLZHAO PRODUCT SPECIFICATION 1 (4) 1/1301-BMR 640 1411+ Uen PKR 4000A series Direct Converters Key Features Industry standard footprint 47.8 x 28.1 x max height 8.0 mm (1.88 x 1.11 x max height 0.32

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 PKM 000 PI series Direct Converters Technical Specification Key Features Industry standard low profile Quarter-brick 57.9 x 36.8 x 8.5 mm (2.28 x 1.45 x 0.33 in) Low profile, max 8.5 mm (0.33 in.) High

More information

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Prepared (also subject responsible if other) JIDGJIAN EAB/FAC/P Susanne Eriksson Ericsson Internal PRODUCT TABLE OF CONTENTS SPECIFICATION 12 (4) (3) No. BPOW 1/131-BMR 21-152 463 Uen Uen Approved Checked

More information

Input V, Output up to 50 A / 165 W

Input V, Output up to 50 A / 165 W Grace EAB/FAC/P Jiang Susanne Eriksson Flex Internal PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (4) (1) 1/131-BMR BPOW 21-152 464 Technical Uen Uen Specification EAB/FAC/P BMR46 series [Susanne PoL Eriksson]

More information

Ordering Information...2 General Information...2 Safety Specification...3 Absolute Maximum Ratings...4

Ordering Information...2 General Information...2 Safety Specification...3 Absolute Maximum Ratings...4 JIDLZHAO PRODUCT SPECIFICATION 1 (3) 1/1301-BMR6401211+ Uen PKR 2000A series Direct Converters Key Features Industry standard footprint 47.8 x 28.1 x max height 8.0 mm (1.88 x 1.11 x max height 0.32 in.)

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Prepared (also subject responsible if other) JIDLZHAO TABLE OF CONTENTS No. 00152-BMR681 Approved Checked Date Rev Reference Technical Specification 2017-09-14 PA12 1 (1) Key Features Industry standard

More information

Technical Specification. BMR 450 Digital PoL Regulators Input V, Output up to 20 A / 100 W

Technical Specification. BMR 450 Digital PoL Regulators Input V, Output up to 20 A / 100 W Kevin ESLUOAN Zhou PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (2) (4) 1/1301-BMR 001 52-EN/LZT 450+ 146 Uen 400 Uen BMR 450 Digital PoL Regulators Technical Specification Kevin SEC/D Zhou (Julia You) 2017-10-12

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Prepared (also subject responsible if other) SEC/S Stella Song Key Features Small package Laydown: 21. x 12.7 x 8.2 mm (.827 x.5 x.323 in) SIP: 2.8 x 7.6 x 15.6 mm (.82 x.3 x.612 in).6 V - 5. V output

More information

DC/DC power module 5V / 3A / 15W

DC/DC power module 5V / 3A / 15W PKF 4211A I DC/DC power module 5V / 3A / 15W SMD and through-hole versions with ultra low component height 8.0 mm (0.315 in.) 81% efficiency at full load 1,500 Vdc isolation voltage Switching frequency

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Prepared (also subject responsible if other) SEC/S Stella Song Key Features Small package 12.2 x 12.2 x 8.0 mm (0.48 x 0.48 x 0.315 in) 0.6 V - 5.0 V output voltage range High efficiency, typ. 96 % at

More information

Input V, Output up to 6 A / 30 W

Input V, Output up to 6 A / 30 W jidgjian PMT 8318VS Grace Jiang series PoL RegulatorsGhasem 7/3/2018 6/19/2018 PA3 PA1 Key Features Compact and low profile package 12.2 x 12.2 x 7.2 mm (0.48 x 0.48 x 0.283 in) High efficiency, typ. 95.1%

More information

50 W DC/DC power module 48 V input series

50 W DC/DC power module 48 V input series PKN 4000 I Series 50 W DC/DC power module 48 V input series Contents Product Program...................... 2 Quality Statement..................... 2 Reliability............................ 2 Limitation

More information

25 40 W DC/DC Power Modules 48 V Input Series

25 40 W DC/DC Power Modules 48 V Input Series PKE 4000 I 25 40 W DC/DC Power Modules 48 V Input Series Single, dual and triple output 10.7 mm (0.42 in.), allows 0.8 in. board spacing 1,500 V dc isolation voltage MTBF >2 million hours at +75 C case

More information

DC/DC Converter Input Vdc Output up to 8A/40W

DC/DC Converter Input Vdc Output up to 8A/40W PKA 2000 I DC/DC Converter Input 19-34 Vdc Output up to 8A/40W Key Features Single, dual and triple output 500 V dc isolation voltage MTBF >2 million hours at 75 C case temperature Complete, no extra filters

More information

BMR 464 series POL Regulators Input V, Output up to 40 A / 132 W

BMR 464 series POL Regulators Input V, Output up to 40 A / 132 W Prepared (also subject responsible if other) EAB/FAC/P Johan Hörman Key Features Small package 3.85 x 2. x 8.2 mm (1.215 x.787 x.323 in) SIP: 33. x 7.6 x 18.1 mm (1.3 x.3 x.713 in).6 V - 3.3 V output voltage

More information

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Kevin SEC/S Zhou Marshall Wang PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (4) (1) 1/1301-BMR 673 Uen Kevin Zhou 09/22/2017 2015-12-24 F A Key Features Industry standard Sixteenth-brick 33.02 x 22.86 x 9.40

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Kevin Zhou PRODUCT SPECIFICATION 1 (4) 1/1301-BMR 673 04 Uen Kevin Zhou 2017-09-27 B Key Features Industry standard Sixteenth-brick Through hole version: 33.02 x 22.86 x 9.40 mm (1.30 x 0.90 x 0.37 in.)

More information

Ericsson Internal. Soldering Information. General Information Safety Specification Absolute Maximum Ratings

Ericsson Internal. Soldering Information. General Information Safety Specification Absolute Maximum Ratings E PRODUCT TABLE OF CONTENTS SPECIFICATION ESLUOAN SEC/S ESLUOAN Approved PMR series Regulators PMR 8000 8000 series PoL Regulator EAB/FAC/P SEC/D (Julia[Susanne You) Eriksson] 1 (1) (4) Checked Input Input

More information

Input V, Output up to 18 A / 60 W

Input V, Output up to 18 A / 60 W BNEPBCDBA E/FAC/P Susanne Grace Jiang Eriksson Flex Internal PRODUCT TLE OF CONTENTS SPECIFICATION 1 (4) (2) 1/1301-BMR BPOW 00201-00152 461 Technical Uen Uen Specification BNEPBCDBA E/FAC/P BMR461 series

More information

W DC/DC Power Modules 48V Input Series

W DC/DC Power Modules 48V Input Series PKJ 4000 PI 37.5-150W DC/DC Power Modules 48V Input Series High efficiency 91.5% Typ (5V) at full load Industry standard footprint Max case temperature +100ºC Wide input voltage range according to ETSI

More information

25 40 W DC/DC Power Modules 24 V Input Series

25 40 W DC/DC Power Modules 24 V Input Series PKA 2000 I 25 40 W DC/DC Power Modules 24 V Input Series Single, dual and triple output 500 V dc isolation voltage MTBF >2 million hours @75 C case temperature Complete, no extra filters or heatsinks required

More information

DC/DC converter Input Vdc Output up to 15A/60W

DC/DC converter Input Vdc Output up to 15A/60W PKG 4000 I DC/DC converter Input 38-72 Vdc Output up to 15A/60W Size 74.7x63.5x11.0 mm (2.94x2.50x0.433 in.) Efficiency typ 86% (5 V) at full load 1500 V dc isolation voltage MTBF >200 years at +75 C case

More information

SMT10E Series. 3.0 Vin to 5.5 Vin Single output. SMT10E Series 10 A DC-DC Converter E Class Non-Isolated

SMT10E Series. 3.0 Vin to 5.5 Vin Single output. SMT10E Series 10 A DC-DC Converter E Class Non-Isolated SMT10E Series 3.0 Vin to 5.5 Vin Single output 10 A Current rating Input voltage range: 3.0 Vdc to 5.5 Vdc Output voltage range: 0.8 Vdc to 3.63 Vdc Ultra high efficiency: 96% @ 5 Vin and 3.3 Vout Extremely

More information

Input V, Output up to 25 A / 300 W

Input V, Output up to 25 A / 300 W Prepared (also subject responsible if other) SEC/S EZHIXZH Kevin Zhou Ericsson Internal PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (2) () No. 1/131-12-FGC11183 BMR 47 Technical Uen Specification Approved

More information

Safety Approvals. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Safety Approvals. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 JIDLZHAO PRODUCT SPECIFICATION 1 (4) 1/1301-BMR 67104 Uen Key Features Industry standard low profile Sixteenth-brick 33.02 x 22.86 x 9.6 mm (1.30 x 0.90 x 0.38 in) High efficiency, typ. 92 % at 24 Vout

More information

0.8V Vin Single output

0.8V Vin Single output SIL15E-12V SERIES 0.8V - 3.63Vin Single output 15A Current rating Input voltage range: 10.0V - 14.0V Output voltage range: 0.8V - 3.63V Ultra high efficiency: 94% @ 12Vin and 3.3Vout Extremely low internal

More information

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ericsson Internal. Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Prepared (also subject responsible if other) EAB/FAC/P JIDGJIAN Susanne Eriksson Ericsson Internal TABLE PRODUCT OF CONTENTS SPECIFICATION 21 (4) (3) No. BPOW 1/131-BMR 21-152 462 Uen Uen Approved Checked

More information

30 60 W DC/DC Power Modules 48 V Input Series

30 60 W DC/DC Power Modules 48 V Input Series PKG 4000 I 30 60 W DC/DC Power Modules 48 V Input Series Efficiency typ 86% (5 V) at full load Low profile 11.0 mm (0.43 in.) 1,500 V dc isolation voltage (duals = 1,000 Vdc) MTBF >200 years at +75 C case

More information

Volant NEA005 Series Non-Isolated 5A SIP/SMT DC/DC Converters

Volant NEA005 Series Non-Isolated 5A SIP/SMT DC/DC Converters Typical units FEATURES Small size, minimal footprint SMT/SIP package 5A Output Current (all voltages) High Efficiency: up to 92% High reliability RoHS Compliant Cost efficient open frame design Output

More information

YEV09T06 6A DC-DC POL Converter 4.5V to 13.8V Input 0.59V to 5.1V Output Data Sheet

YEV09T06 6A DC-DC POL Converter 4.5V to 13.8V Input 0.59V to 5.1V Output Data Sheet Member of the Family Applications Low voltage, high density systems with Intermediate Bus Architectures (IBA) Point-of-load regulators for high performance DSP, FPGA, ASIC, and microprocessors Desktops,

More information

Technical Specification 2. BMR45 series Fully regulated Advanced Bus Converters Input V, Output up to 60 A / 396 W PRODUCT SPECIFICATION 2 (5)

Technical Specification 2. BMR45 series Fully regulated Advanced Bus Converters Input V, Output up to 60 A / 396 W PRODUCT SPECIFICATION 2 (5) Ericsson PRODUCT Internal SPECIFICATION 1 (5) Prepared (also subject responsible if other) TABLE OF CONTENTS 1 (1) Prepared (also subject responsible if other) Kevin Zhou 1/131- BMR 453 Technical Uen Specification

More information

E Class Converters. EHS20 1.2V Model. Technical enquiries tel:

E Class Converters. EHS20 1.2V Model.   Technical enquiries   tel: Model 1.2V Units Parameter Output Voltage Setpoint 1.18 1.22 Vdc Line/Load Regulation Max 0.1% / 0.2% % Vo Output total regulation 1.16 1.24 Vdc Output adjust (note 4) 90-110 %Vo,nom Remote-sense Comp.

More information

DC/DC regulators Input V Output Current 12A

DC/DC regulators Input V Output Current 12A PMA 5000 Series DC/DC regulators Input 4.5-5.5V Output Current 12A Key Features Surface mountable Low profile, max 8.5mm (0.33 in) High efficiency Low weight Designed for Environment, DfE Lead-free / Bromine-free

More information

Single negative output

Single negative output SIL25C SERIES Single negative output Trim range (-4.5 Vdc to -5.5 Vdc) High power density design means reduced board space requirement Remote sense Power good output signal (open collector) Operating ambient

More information

PTH Vin single output. DC/DC CONVERTERS POLA Non-isolated 1. NEW Product

PTH Vin single output. DC/DC CONVERTERS POLA Non-isolated 1. NEW Product PTH0 DC/DC CONVERTERS POLA Non-isolated 0 A output current V input voltage Wide-output voltage adjust. Vdc to 5.5 Vdc for suffix W and 0.8 Vdc to.8 Vdc for suffix L Auto-track sequencing* Margin up/down

More information

Features. Block Diagram

Features. Block Diagram Features WATT SMT SINGLE SMT Technology 2:1 Input Range Efficiency up to 8 I/O Isolation 100 Short Circuit Protected MTBF > 1,000,000 Hours RoHS Compliant MSL2 (Moisture Sensitivity Level) per IPC/JEDEC

More information

Output Input Efficiency PARD (mvp-p) Vin Nom. (V)

Output Input Efficiency PARD (mvp-p) Vin Nom. (V) Features: Small size, minimal footprint SMT/SIP package 5A Output Current (all voltages) High Efficiency: up to 94% High reliability RoHS Compliant Cost efficient open frame design Output voltage programmable

More information

15 18 W DC/DC Power Modules 24 V Input Series

15 18 W DC/DC Power Modules 24 V Input Series PKC 2000 I 15 18 W DC/DC Power Modules 24 V Input Series Regulated single, dual and triple outputs Low profile 10.7 mm (0.42 in.), allows 0.8" board pitch 0.6 in. if recessed in the printed board Proven

More information

15 18 W DC/DC Power Modules 48 V Input Series

15 18 W DC/DC Power Modules 48 V Input Series PKC 4000 I 15 18 W DC/DC Power Modules 48 V Input Series Regulated single, dual and triple outputs Low profile 10.7 mm (0.42 in.), allows 0.8 in. board pitch 0.6 in. if recessed in the printed board Proven

More information

YNV12T05 DC-DC Converter Data Sheet VDC Input; VDC 5 A

YNV12T05 DC-DC Converter Data Sheet VDC Input; VDC 5 A The Products: Y-Series Applications Intermediate Bus Architectures Telecommunications Data communications Distributed Power Architectures Servers, workstations Benefits High efficiency no heat sink required

More information

SMT20C SERIES. Single Output TÜV. SMT20C Series 20 A DC-DC Converter C Class Non-Isolated

SMT20C SERIES. Single Output TÜV. SMT20C Series 20 A DC-DC Converter C Class Non-Isolated SMT20C SERIES Single Output Wide output voltage trim (0.9 Vdc to 5.0 Vdc, 20 A max.) Power good output signal (open collector) Input undervoltage lockout Current sink capability for termination applications

More information

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4

Ordering Information... 2 General Information... 2 Safety Specification... 3 Absolute Maximum Ratings... 4 Nick Kevin Cao Zhou PRODUCT Ericsson Internal SPECIFICATION TABLE OF CONTENTS () () /-BMR PKUA Series Fully Regulated DC-DC Kevin Zhou -- -9- B Key Features Low profile sixteenth-brick. x. x. mm (. x.9

More information

Ordering Information PT5521 =3.3 Volts PT5522 =2.5 Volts PT5523 =2.0 Volts PT5524 =1.8 Volts PT5525 =1.5 Volts PT5526 =1.2 Volts PT5527 =1.

Ordering Information PT5521 =3.3 Volts PT5522 =2.5 Volts PT5523 =2.0 Volts PT5524 =1.8 Volts PT5525 =1.5 Volts PT5526 =1.2 Volts PT5527 =1. PT552 Series 1.5-A 5-V/3.3-V Input Adjustable Integrated Switching Regulator SLTS147A (Revised 1/5/21) Features Single-Device: 5V/3.3V Input DSP Compatible 89% Efficiency Small Footprint Space-Saving package

More information

CLP0205 Open Frame Power Supply Vac input; 5Vdc output; 200W Output Power; 0.25A stdby

CLP0205 Open Frame Power Supply Vac input; 5Vdc output; 200W Output Power; 0.25A stdby ; 12Vout @ 0.25A stdby Applications Industrial equipment LED Signage Telecommunications equipment Description Features Compact size 50.8mm x 101.6mm x 36.1mm (2in x 4in x 1.4in) with density of 18W/in

More information

Ordering Information PT4486o = 6.5 to 17.5 Volts PT4497o = 8.5-A Booster. PT Series Suffix (PT1234x)

Ordering Information PT4486o = 6.5 to 17.5 Volts PT4497o = 8.5-A Booster. PT Series Suffix (PT1234x) PT4486 48V 100-W 8.5-A Programmable Isolated DC/DC Converter SLTS11B (Revised 6//0) Features 36V to 75V Input Voltage Range Programmable Output Voltage Range: 6.5V to 17.5V -40 to 85 C Operating Temp 1500

More information

SIL20C SERIES. Single Output. SIL20C Series 20 A DC-DC Converter C Class Non-Isolated

SIL20C SERIES. Single Output. SIL20C Series 20 A DC-DC Converter C Class Non-Isolated SIL20C SERIES Single Output Wide output voltage trim (0.9 Vdc to 5.0 Vdc, 20 A max.) Power good output signal (open collector) Input undervoltage lockout Current sink capability for termination applications

More information

Volant NEA005 Series. Non-Isolated 5A SIP/SMT DC/DC Converters. FEATURES. Small size, minimal footprint SMT/SIP package

Volant NEA005 Series. Non-Isolated 5A SIP/SMT DC/DC Converters.   FEATURES. Small size, minimal footprint SMT/SIP package Typical units FEATURES Small size, minimal footprint SMT/SIP package 5A Output Current (all voltages) High Efficiency: up to 92% High reliability RoHS Compliant Cost efficient open frame design Output

More information

1 V/ms V typ. Track input voltage: Pin 8 (See Note 6, page 3) ± 0.3 Vin

1 V/ms V typ. Track input voltage: Pin 8 (See Note 6, page 3) ± 0.3 Vin 1 Vin 1 of 5 Total Power: Watts # of Outputs: Single Special Features A output current 1 V input voltage Wide-output voltage adjust 1. Vdc - 5.5 Vdc for suffix W & 0.8 Vdc - 1.8 Vdc for suffix L Auto-track

More information

BMR 463 series POL Regulators Input V, Output up to 20 A / 66 W

BMR 463 series POL Regulators Input V, Output up to 20 A / 66 W EAB/FAC/P Johan Hörman PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (4) 1/1301-BMR 00152-EN/LZT 463 146 Technical Uen 434 Uen BMR 463 series POL Regulators Key Features Small package 25.65 x 13.8 x 8.2

More information

One part that covers many applications Reduces board space, system cost and complexity, and time to market. North America

One part that covers many applications Reduces board space, system cost and complexity, and time to market. North America Bel Power Solutions point-of-load converters are recommended for use with regulated bus converters in an Intermediate Bus Architecture (IBA). The YEV09T, non-isolated DC-DC point of load (POL) converter,

More information

DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output

DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output THN 20WI Series Application Note DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output Pending Applications Wireless

More information

Output Input Efficiency PARD (mvp-p) Vin Nom. Regulation Max (V)

Output Input Efficiency PARD (mvp-p) Vin Nom. Regulation Max (V) Features: Small size, minimal footprint SMT/SIP package A Output Current (all voltages) High Efficiency: up to 9% High reliability RoHS Compliant Cost efficient open frame design Output voltage programmable

More information

1 V/ms Undervoltage lockout: V typ. Track input voltage: Pin 8 (See Note 6, page 3) ± 0.3 Vin

1 V/ms Undervoltage lockout: V typ. Track input voltage: Pin 8 (See Note 6, page 3) ± 0.3 Vin PTH0 SERIES PTH0 Vin Total Power: 55 Watts # of Outputs: Single Special Features 0 A output current V input voltage Wide-output voltage adjust. Vdc - 5.5 Vdc for suffix W & 0.8 Vdc -.8 Vdc for suffix L

More information

Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/18A out, 216W

Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/18A out, 216W FEATURES High efficiency : 94.7% @ 12V/18A Size: 57.9x36.8x11.2mm (2.28 x1.45 x0.44 ) (w/o heat spreader) 57.9*36.8*12.7mm(2.28 *1.45 0.50 ) (with heat spreader) Standard footprint Industry standard pin

More information

Volant NCF010 Series. Non-Isolated 10A SIP DC/DC Converters

Volant NCF010 Series. Non-Isolated 10A SIP DC/DC Converters Features: Small size, minimal footprint/low profile A Output Current (all voltages) High Efficiency: up to 95% High reliability RoHS Compliant Cost efficient open frame design Pre-bias monotonic start-up

More information

QUARTER-BRICK SERIES Single Output Performance Products

QUARTER-BRICK SERIES Single Output Performance Products Quarter-Brick Series 100 A DC-DC QUARTER-BRICK SERIES Single Output Performance Products High efficiency topology High output current Low profile, 0.300 inch (7.62 mm) height Unprecedented useable output

More information

48/60 V (max 72 V dc)

48/60 V (max 72 V dc) Regulated single, dual and triple outputs. Low profile 10.7 mm (0.42 in.), allows 0.8 in. board pitch 0.6 in. if recessed in the printed board Proven MTBF >2,000,000 hours at +75 C case temperature and

More information

SPS20 Series small size isolated DC/DC converters

SPS20 Series small size isolated DC/DC converters SPS20 Series small size isolated DC/DC converters Features High Efficiency Wide operating temperature range ( -20 C to +71 C ) Wide 2:1 input range Built in over current protection circuit Input Output

More information

Features. Applications. QD48T DC-DC Converter Data Sheet VDC Input; 1.8 and A Output

Features. Applications. QD48T DC-DC Converter Data Sheet VDC Input; 1.8 and A Output The QD48T1833 dual output through-hole mounted DC-DC converter offers unprecedented performance in a quarter brick package by providing two independently regulated high current outputs. This is accomplished

More information

CLP0112 Open Frame Power Supply Vac input; 12Vdc output; 150W Output Power

CLP0112 Open Frame Power Supply Vac input; 12Vdc output; 150W Output Power Applications Telecommunications equipment Embedded Computing Storage Systems Industrial equipment Features Compact size 50.8 mm x 101.6 mm x 36.1 mm (2 in x 4 in x 1.4 in) with density of 13.4W/in 3 Universal

More information

di/dt Nex TM-v Series: YNV12T05

di/dt Nex TM-v Series: YNV12T05 Features PRODUCTS: Nex TM FAMILY Applications Intermediate Bus Architectures Telecommunications Data Communications Servers, Workstations Distributed Power Architectures Benefits High efficiency no heat

More information

PTH03010Y & PTH05010Y PTH12010Y. Vin increasing Vin decreasing PTH05010Y PTH12010Y PTH12010Y

PTH03010Y & PTH05010Y PTH12010Y. Vin increasing Vin decreasing PTH05010Y PTH12010Y PTH12010Y PTHxx00Y 3.3/5/ Rev. 3.3.09_3 of 5 Total Power: Watts # of Outputs: Single Special Features bus termination output (output the system V REF ) 5 A output current 3.3, 5, or Vdc input voltage DDR and QDR

More information

24 Austin Lynx TM : Non-Isolated DC-DC Power Modules 20Vdc 30Vdc input; 5.0 Vdc to 15 Vdc output; 70W Output Power

24 Austin Lynx TM : Non-Isolated DC-DC Power Modules 20Vdc 30Vdc input; 5.0 Vdc to 15 Vdc output; 70W Output Power 24 Austin Lynx TM : Non-Isolated DC-DC Power Modules 20Vdc 30Vdc input; 5.0 Vdc to 15 Vdc output; 70W Output Power RoHS Compliant Features Compliant to RoHS EU Directive 2011/65/EU (-Z versions) Compliant

More information

H80SV12017 * * FEATURES. Delphi Series H80SV, half Brick Family DC/DC Power Modules: 16.8~137.5 Vin, 54/48/24/15/12Vout,200W APPLICATIONS

H80SV12017 * * FEATURES. Delphi Series H80SV, half Brick Family DC/DC Power Modules: 16.8~137.5 Vin, 54/48/24/15/12Vout,200W APPLICATIONS H80SV12017 200W DC/DC Power Modules Delphi Series H80SV, half Brick Family DC/DC Power Modules: 16.8~137.5 Vin, 54/48/24/15/12Vout,200W The H80SV series Half-Brick is isolated 200W DC/DC converters with

More information

SPS20 Series small size isolated DC/DC converters

SPS20 Series small size isolated DC/DC converters 18 36Vdc Input, Maximum Power: 20W FEB 10, 2011 SPS20 Series small size isolated DC/DC converters Features High Efficiency Wide operating temperature range ( -20 C to +71 C ) Wide 2:1 input range Built

More information

TBD. Delphi E36SR Series DC/DC Power Modules: 18~60 in, 12V/4A out, 48W FEATURES OPTIONS APPLICATIONS

TBD. Delphi E36SR Series DC/DC Power Modules: 18~60 in, 12V/4A out, 48W FEATURES OPTIONS APPLICATIONS FEATURES High efficiency: 91% @ 12V/4A Size: 58.4x22.8x8.73mm (2.30 x0.90 x0.34 ) Standard footprint Industry standard pin out TBD Fixed frequency operation Input UVLO, Output OCP, OVP, OTP 1500V isolation

More information

ABC400 Series is a compact and efficient series of AC-DC open frame power supplies suited for telecom, datacom and many other applications.

ABC400 Series is a compact and efficient series of AC-DC open frame power supplies suited for telecom, datacom and many other applications. is a compact and efficient series of AC-DC open frame power supplies suited for telecom, datacom and many other applications. The family meets the international information technology safety standards

More information

QME48T40 DC-DC Series Data Sheet VDC Input; A Output

QME48T40 DC-DC Series Data Sheet VDC Input; A Output Applications Telecommunications Data communications Wireless communications Servers, Workstations Benefits High efficiency no heat sink required Higher current capability at 70 ºC than most competitors

More information

PTH03060Y & PTH05060Y PTH12060Y. Vin increasing Vin decreasing PTH05060Y PTH12060Y PTH12060Y

PTH03060Y & PTH05060Y PTH12060Y. Vin increasing Vin decreasing PTH05060Y PTH12060Y PTH12060Y 3.3/5/ of 5 Total Power: Watts # of Outputs: Single Special Features V TT bus termination output (output the system V REF ) 0 A output current 3.3, 5 or Vdc input voltage DDR and QDR compatible ON/OFF

More information

Input V, Output up to 80 A / 200 W

Input V, Output up to 80 A / 200 W INTERNAL ERICSSON USE INTERNAL ONLY PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (4) (1) jidgjian Grace Jiang 1/1301-BMR BPOW 00201-00152 469 Technical Uen Specification jidgjian Susanne BMR469 Grace Eriksson

More information

SE014S110 Power Module; dc-dc Converter: 48 Vdc Input, 110 Vdc Output, 14 W

SE014S110 Power Module; dc-dc Converter: 48 Vdc Input, 110 Vdc Output, 14 W Data Sheet SE014S110 Power Module; dc-dc Converter: Features The SE014S110 Power Module uses advanced, surface-mount technology and delivers high-quality, compact, dc-dc conversion at an economical price.

More information

QPW050/060 Series Power Modules; DC-DC converters 36-75Vdc Input; 1.2Vdc to 3.3Vdc Output

QPW050/060 Series Power Modules; DC-DC converters 36-75Vdc Input; 1.2Vdc to 3.3Vdc Output RoHS Compliant Applications Distributed power architectures Wireless Networks Access and Optical Network Equipment Enterprise Networks Latest generation IC s (DSP, FPGA, ASIC) and Microprocessor powered

More information

DC/DC power module ±9V to ±15V /0.85A /15W

DC/DC power module ±9V to ±15V /0.85A /15W PKF 4221 ASI DC/DC power module ±9V to ±15V /0.85A /15W SMD and through-hole versions with ultra low component height 8.0 mm (0.315 in.) 84% efficiency at full load 1,500 Vdc isolation voltage MTTF >10

More information

Technical Specification

Technical Specification PRODUCT TABLE OF CONTENTS SPECIFICATION 1 (1) (4) SEC/S Marshall 1/131-BMR 15-EN/LZT 455 146 443 Uen EAB/FAC/P 13--7 13--6 PB4 A EN/LZT 146 43 D R3A March 14 Key Features Industry standard low profile

More information

MTE1 Series Isolated 1W Single Output SM DC/DC Converters

MTE1 Series Isolated 1W Single Output SM DC/DC Converters MTE1 Series SELECTION GUIDE FEATURES Single isolated output 1kVDC Isolation Hi Pot Test Typical efficiency 86% Wide temperature performance at full 1 Watt load, 4 C to 85 C UL 69 recognised 3.3V, 5V, 12V,

More information

SGM2553/SGM2553D Precision Adjustable Current Limited Power Distribution Switches

SGM2553/SGM2553D Precision Adjustable Current Limited Power Distribution Switches /D GENERAL DESCRIPTION The and D power distribution switches are intended for applications where precision current limiting is required or heavy capacitive loads and short circuits are encountered and

More information

YH09T40 40A DC-DC POL Converter 5V to 13.8V Input 0.6V to 3.63V Output Data Sheet

YH09T40 40A DC-DC POL Converter 5V to 13.8V Input 0.6V to 3.63V Output Data Sheet Member of the Family Applications Low voltage, high density systems with Intermediate Bus Architectures (IBA) Point-of-load regulators for high performance DSP, FPGA, ASIC, and microprocessors Desktops,

More information

200 WATT TH SERIES DC/DC CONVERTERS

200 WATT TH SERIES DC/DC CONVERTERS Features 4:1 Input voltage range High power density Small size 2.4 x 2.28 x 0.65 Efficiency up to 90 Excellent thermal performance with metal case Pulse-by-pulse current limiting Over-temperature protection

More information

QBW025A0B Series Power Modules; DC-DC Converters Vdc Input; 12Vdc Output; 25 A

QBW025A0B Series Power Modules; DC-DC Converters Vdc Input; 12Vdc Output; 25 A Document No: PDF Name: 36-75 Vdc Input; 12Vdc Output; 25 A Applications Distributed power architectures Servers and storage applications Access and Optical Network Equipment Enterprise Networks Options

More information

CLP0224 Open Frame Power Supply Vac input; 24Vdc output; 200W Output Power

CLP0224 Open Frame Power Supply Vac input; 24Vdc output; 200W Output Power Applications Industrial equipment Telecommunications equipment Features Compact size 50.8 mm x 101.6 mm x 37.25 mm (2 in x 4 in x 1.47 in) with density of 18 W/in 3 Universal AC Input Range (90 264VAC)

More information