LINEAR LINK QUICK REFERENCE MANUAL Basic Installation, Programming & Troubleshooting
|
|
- Alannah O’Neal’
- 6 years ago
- Views:
Transcription
1 8930 S Beck Ave., Suite 107 Tempe, Arizona U.S.A. Telephone (480) Fax (480) LINEAR LINK QUICK REFERENCE MANUAL Basic Installation, Programming & Troubleshooting The specifications contained in this manual are subject to change without notice and any user of these specifications should verify from the manufacturer that the specifications are currently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications that have been changed and are no longer in effect. TM REV. A PUBLISHED BY FLOW TECHNOLOGY, INC. July 2008
2 TM REVISIONS TM Linear Link Quick Reference Manual Page 2 of 12
3 Table of Contents Wiring / Set Up Wiring set up...page 4 Output Connections & Definitions...Page 5 Programming Visual Link Program Install/Setup...Page 7 Changing Units for Mass Flow or Volumetric...Page 9 Editing, Saving & Loading Job Files...Page 11 Troubleshooting Linear Link Troubleshooting...Page 12 Wiring/Setup TM Linear Link Quick Reference Manual Page 3 of 12
4 Step# 1 - Determine the model # of the Linear Link. LN C - V1-1 POWER 5 = 10 TO 32 VDC FLOW METER INPUT A = MAGNETIC B = PULSE C = RF CARRIER D = OTHER RF CARRIER ENCLOSURE -0 = NO ENCLOSURE B6 = NEMA 4X B7 = NEMA 4X WITH MS CONNECTOR -9 = CLASS 1, DIV, GROUP A, B, C & D A7 = DUST TIGHT ALUMINUM WITH MS CONNECTOR -F = CLASS 1, DIV 1, GROUP B, C & D -1 = INTEGRAL PICKOFF, 10-PIN MS BA = NEMA 4X, UNIVERSAL DISPLAY, MX CONN BC = NEMA 4X, UNIVERSAL DISPLAY ANALOG OUTPUT V1 = ANALOG VOLTAGE (0 TO 10 VDC) FOR FLOW RATE MA = ANALOG CURRENT (4 TO 20 ma) FOR FLOW RATE Step# 2 Wire the Linear Link according to the appropriate table. (Table 4 explains the inputs & outputs) LN Table 1 LN Table 2 LN BC - Table 2 LN B6 - Table 2 LN F - Table 2 LN B7 - Table 3 LN A7 - Table 3 LN BA - Table 3 Step# 3 Verify the output by putting flow through the meter and monitoring the output. The Linear Link has been programmed at the factory with the calibration data for the meter. There is no need to reprogram the unit (unless instructed to by FTI). If there is no output from the Linear Link go to the troubleshooting guide at the end of this manual. Step# 4 You re done! The Linear Link is ready for use. TM Linear Link Quick Reference Manual Page 4 of 12
5 Output Connections & Definitions Table 1: Electrical Connections, Pickoff Version (For models, LN ) Linear Link Function Pin (10- Pin Connector) POWER +10 to +32 VDC (Supply) A CIRCUIT COMMON Power and Signal Common B TX Serial Transmit Data C RX Serial Receive Data D F LIN Linearized Pulse Output E F RAW Non-Linearized Pulse Output F VOLTAGE OUT Voltage Out G CURRENT OUT Current Out H NOT USED NOT USED J K Table 2: Electrical Connections, NEMA 4X & Condulet Versions (For models, LN , LN BC -, LN B6 - LN F - ) Linear Link Function Terminal Strip (NEMA 4X and Metal Conduit) Version (PCB 12-Pin) POWER +10 to +32 VDC (Supply) 1 POWER RETURN Power Return 2 + XDCR Pickoff Input 3 - XDCR Pickoff Input 4 F LIN Linearized Pulse Output 5 F RAW Non-Linearized Pulse Output 6 VOLTAGE OUT Voltage Out 7 CURRENT OUT Current Out 8 CIRCUIT COMMON 9, 10, 11, 12 TM Linear Link Quick Reference Manual Page 5 of 12
6 Table 3: Electrical Connections, NEMA 4X with 3-pin & 10-pin MS Connectors (For models, LN B7 -, LN A7 -, LN BA - ) Linear Link Function Terminal Strip PCB (Pin #) MS (NEMA 4X & Aluminum) Version (10-Pin, J1 and 3-pin, J2) POWER +10 to +32 VDC (Supply) 1 J1-A POWER RETURN Power Return 2 J1-B F LIN Linearized Pulse Output 5 J1-C F RAW Non-Linearized Pulse Output 6 J1-D VOLTAGE OUT Voltage Out 7 J1-E CURRENT OUT Current Out 8 J1-F CIRCUIT COMMON 9 J1-G CIRCUIT COMMON 11 J1-H + XDCR Pickoff Input 3 J2-A - XDCR Pickoff Input 4 J2-B CIRCUIT COMMON 10 J2-C Table 4: Link Outputs The linearized scaled flowrate output is available as a analog and pulse signal output F Lin F Raw Voltage Out Current Out Linearized pulse output (5 Volt amplitude). This pin has a pulse output signal that corresponds to the linearized flow. Unscaled pulse output (5 Volt amplitude). This pin has the amplified output signal of the flowmeter before linearization. This is useful for monitoring the raw frequency generated by the flowmeter. It can also be used to inject a pulse for verifying calibrations. Pulse input (0-5 Volt amplitude, absolute max of 10V). This is the input pin for pulse input flowmeters Volt output. This pin provides an analog voltage output signal that corresponds to the linearized flowrate. 4-20mA output. This pin provides an analog milliamp output signal that corresponds to the linearized flowrate. Use only on units configured for current output. This output is locally powered and must be returned to the common pin not to a voltage source. TM Linear Link Quick Reference Manual Page 6 of 12
7 Visual Link Program Install/Set Up NOTE: The only time the Visual Link software should be used is to modify or rescale the Linear Link programming. It is not intended to be used as a troubleshooting tool. Step# 1 Download and install the software. Visual Link Software is available from the FTI website at Step# 2 Hook up the smart cable from the computer to the Linear Link. Smart Cable Part# is used on the pickoff version of the Linear Link (MS connector). Smart Cable Part# is used on all other Linear Link models (modular connector). Step# 3 Establish a connection with the Linear Link using the Visual Link Software Establish Communication Button on the Connection Status tab (circled below). TM Linear Link Quick Reference Manual Page 7 of 12
8 Step# 4 - Transfer the data from the Linear Link to the Visual Link software by clicking the read EPROM button (circled below). Once the button is clicked, press ok and the data will transfer. When the data is transferred click close button. Step# 5 Make any changes. Changes must be saved to the computer as a new.job file. Step# 6 Transfer the data to the Linear Link. The new information can be transferred to the Linear Link by clicking the transmit button (circled below). When completed click the close button. TM Linear Link Quick Reference Manual Page 8 of 12
9 Changing Units for Mass Flow or Volumetric Step# 1 - Connect to the Linear Link as described on page 6. Step# 2 -Open the System Parameters tab Step# 3 - In the System Parameters tab, change the units where it indicates Flow Output Units. If changing the time base (minutes to hours) the K-Factor units will need to be changed. If time base remains the same then only the Flow Output Units will need to be modified. TM Linear Link Quick Reference Manual Page 9 of 12
10 Step# 4 - If the time base is changing, the K-Factor units will need to be changed. Select Configure on the toolbar and then select the Mechanical Parameters. Step# 5 - In the Mechanical Parameters screen; change the time base units only. Step# 6 - Save the job file and write it to the EPROM in the Linear Link. TM Linear Link Quick Reference Manual Page 10 of 12
11 Editing, Saving & Loading Job Files Step# 1 - Connect to and transfer the data from the Linear Link as described on page 6. Step# 2 Save the data to a.job file. It is recommended to save the original data to a.job file before making any changes. This allows recovery if any mistakes are made. Step# 3 - Make the changes to the configuration. Once the changes are made, save the modified data to a new.job file. Step# 4 - Program the job information into the Linear Link EPROM (see page 8 for transferring data to the Linear Link ). Note: To obtain a copy of the original.job file, contact TM Linear Link Quick Reference Manual Page 11 of 12
12 Linear Link Trouble Shooting TM Linear Link Quick Reference Manual Page 12 of 12
INSTALATION, OPERATION & MAINTENANCE MANUAL. PA-1001A Series SIGNAL CONDITIONER & CONVERTORS
INSTALATION, OPERATION & MAINTENANCE MANUAL FOR PA-1001A Series SIGNAL CONDITIONER & CONVERTORS PA1001A 7/02 Page 1 of 11 SIGNAL CONDITIONER & CONVERTERS PA1001A Series INTRODUCTION: The PA1001A series
More informationInstallation, Operation and Maintenance Manual
TM M723 Rev. C Model 1050 Strain Gage Transmitter Installation, Operation and Maintenance Manual Table of Contents General... 1 Installation... 1 Specifications... 1 Wiring... 2 Setup and Operation...
More informationCEC VIBRATION TRANSMITTER
CEC 1-808 VIBRATION TRANSMITTER Operation & Maintenance Manual 746 Arrow Grand Circle Covina, CA 91722 United States of America Tel: (626) 938-0200 Fax: (626) 938-0202 Internet: http://www.cecvp.com E-mail:
More informationTECHNICAL NOTES MT-4 Radio Systems TN182 Battery Level Reporting and Remote P25 Test Tone
Battery Level Reporting is a method of activating a repeater remotely to have it transmit a signal that reports the battery voltage level over RF. The Remote P25 Test Tone is a remotely activated Standard
More informationIOM. Model 1050 Strain Gage Transmitter Installation & Operation Manual. (Cage Code #1MU21)
IOM Model 1050 Strain Gage Transmitter Installation & Operation Manual (Cage Code #1MU21) Model 1050 Strain Gage Transmitter Installation & Operation Manual CONTENTS I. GENERAL...1 II. INSTALLATION...2
More informationInstallation & Service Manual
869-894 MHz Installation & Service Manual Model SCA 9321-30C Single-Channel Cellular Amplifier 044-xxxxx Rev.A February 2003 2003 Powerwave Technologies Incorporated. All rights reserved. Powerwave Technologies,
More informationOVEN INDUSTRIES, INC. Model 5C7-362
OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-362 THERMOELECTRIC MODULE TEMPERATURE CONTROLLER TABLE OF CONTENTS Features... 1 Description... 2 Block Diagram... 3 RS232 Communications Connections...
More informationGuardian and DL3282 Modem Interface Technical Service Application Note
Guardian and DL3282 Modem Interface Technical Service Application Note OVERVIEW The following document is designed to provide information for the implementation of the Guardian Wireless Modem/Analog Radio
More informationModel FLSC-C1-LIQ. Microprocessor Based Loop Powered Transmitter
Model FLSC-C1-LIQ Microprocessor Based Loop Powered Transmitter CONTENTS 1. Introduction ------------------------------------------------------------ 2 2. Specifications-----------------------------------------------------------
More informationModel FLSC-C3-XX. DC Powered Microprocessor Controlled Transmitter
Model FLSC-C3-XX DC Powered Microprocessor Controlled Transmitter CONTENTS. Introduction----------------------------------------------------------------- 2 2. Specifications ---------------------------------------------------------------
More informationINSTRUCTION MANUAL PLUG AND SEND WIRELESS MONITOR SYSTEM TABLE OF CONTENTS
DEVAR Inc. 706 Bostwick Ave., Bridgeport CT 06605 Tel 203 368 6751 Fax 203 368 3747 http://www.devarinc.com e-mail: info@devarinc.com INSTRUCTION MANUAL PLUG AND SEND WIRELESS MONITOR SYSTEM TABLE OF CONTENTS
More informationSPEED SENSORS SIGNAL CONDITIONERS. Standard & Custom Sensors, Signal Conditioners and Interface Electronics
for INNOVATIVE SENSOR SOLUTIONS Standard & Custom Sensors, Signal Conditioners and Interface Electronics SPEED SENSORS Magnetic Speed Sensors (Active & Passive) Hall Effect Speed Sensors, GBR (Zero Speed)
More information1-830 SERIES DISPLACEMENT TRANSMITTER
1-830 SERIES DISPLACEMENT TRANSMITTER Operation & Maintenance Manual 746 Arrow Grand Circle Covina, CA 91722 United States of America Tel: (626) 938-0200 Fax: (626) 938-0202 Internet: http://www.cecvp.com
More informationInstallation, Operation and Maintenance Manual
NIAGARA M513 Rev. B Model 1005 Pulse to DC Converter Installation, Operation and Maintenance Manual Table of Contents General... 1 Specifications... 1 Installation... 1 Theory of Operation... 2 Setup...
More informationUnderwater GPS User Manual
Underwater GPS Document number W-DN-17002-3 Project Classification - Rev Prepared by Checked by Approved by Short description 1 2017-08-03 T. Trøite O. Skisland T. Trøite Initial 2 2017-08-04 T. Trøite
More informationTemposonics. M-Series Analogue/PWM Tester. User s Manual. Absolute, Non-Contact Position Sensors. Document Part Number Revision B
Temposonics Absolute, Non-Contact Position Sensors M-Series Analogue/PWM Tester Document Part Number 551132 Revision B Content 1 The M-Series analogue/pwm Test Kit 1.1 Contents and accessories 1.2 Familiarizing
More informationIntroduction to the Analog Discovery
Introduction to the Analog Discovery The Analog Discovery from Digilent (http://store.digilentinc.com/all-products/scopes-instruments) is a versatile and powerful USB-connected instrument that lets you
More informationOperating Instructions
LR650 Operating Instructions This product is an accessory or part of a system. Always read and follow the manufacturer s instructions for the equipment you are connecting this product to. Comply with all
More informationIB6 Series Solid-State Isolation Relay
IB6 Series Solid-State Isolation Relay Installation & Operation Manual TRANSDATA, INC. 2560 TARPLEY ROAD CARROLLTON, TEXAS 75006 TEL (972) 418-7717 FAX (972) 418-7774 Website: www.transdatainc.com E-mail:
More informationOBSOLETE A. For 24-hour Technical Assistance Call
T e m p o s o n i c s 550951 A P o s i t i o n S e n s o r s a n d S y s t e m s T e m p o s o n i c s I O r d e r i n g G u i d e CONTENTS How to order an transducer by model number... 1 How to order
More informationProgrammable K-Factor Scaler B and Programming Software Kit B
Programmable K-Factor Scaler B220-885 and Programming Software Kit B220-900 INSTALLATION & INSTRUCTION MANUAL 8635 Washington Avenue Racine, Wisconsin 53406 Toll Free: 800.235.1638 Phone: 262.639.6770
More informationTECHNICAL NOTES. MT-4 Radio Systems. TN247 VR-4E VHF MT-4E Receiver. Specifications. Models Available. Receiver Operating Frequency
MADE IN CANADA TN247 VR-4E VHF MT-4E Receiver USB CNTL BUS A D RECEIVER FREQUENCY (MHz) SQ. DISABLE NORM OFF REF IN RF IN The VR-4E VHF receiver is an FM radio module capable of analog operation in 12.5
More informationInstruction Manual ABM HART Gateway Software. Instruction Manual Revision A.1
Instruction Manual ABM HART Gateway Software Instruction Manual Revision A.1 Table of Contents Section 1: Getting Started... 3 1.1 Setup Procedure... 3 1.2 Quick Setup Guide for Ultrasonic Sensors... 11
More informationSensor Options. Rev
Sensor Options Rev. 07.21.17 HALL-EFFECT SENSORS DH-X Dual Hall Effect Pickup Used with JV-CG and JV-KG (excluding JVM-01CG) The DH Dual Hall Effect Pickups are microprocessor-based sensors for use with
More informationTECHNICAL INFORMATION BULLETIN
TECHNICAL INFORMATION BULLETIN T/B No.: TIBFM 15-02 Rev A Revision date: JUNE24/08 Issue Date: JUNE18/08 TiL Model: TDFM-600/6000/7000 transceivers with Type I or Type II modules. TiL P/N: 011210-1,-2,-3,-4,-5
More informationMid-West. Instrument. Model 140 Electrical Installation and Operating Instructions. Gauge Front ELECTRICAL
Mid-West Instrument BULLETIN NO. ELEC-IM140/11A Replaces ELEC-IM140-141/09A ELECTRICAL Gauges with switches have one or two SPST or SPDT hermetically sealed adjustable set point reed switch assemblies.
More informationOPERATION AND MAINTENANCE MANUAL TRIAXIAL ACCELEROMETER MODEL PA-23 STOCK NO
OPERATION AND MAINTENANCE MANUAL TRIAXIAL ACCELEROMETER MODEL PA-23 STOCK NO. 990-60700-9801 GEOTECH INSTRUMENTS, LLC 10755 SANDEN DRIVE DALLAS, TEXAS 75238-1336 TEL: (214) 221-0000 FAX: (214) 343-4400
More informationWireless Base Radio. Wireless Transmitters
XYR 5000 Wireless Base Radio 34-XY-03-55 9/2006 WBR/WBH Europe PRODUCT SPECIFICATION AND MODEL SELECTION GUIDE Function The Wireless Base Radio (WBR) is part of the XYR 5000 family of wireless products.
More informationRHE12. Hazardous Area Coriolis Mass Flow Transmitter. Features. Applications. Benefits
RHE12 Hazardous Area Coriolis Mass Flow Transmitter Features Field mounting Compact, pressure safe housing ATEX and CSA approvals for installation in hazardous areas 24 VDC power supply Configurable analog
More informationPage/Talk Weatherproof Wall Stations Models MLW80 and MLW85
7000 Fisher Road S.E., Calgary, Alberta, Canada T2H 0W3 Telephone 403-258-3100 Fax 403-253-4967 Website: www.guardiantelecom.com Page/Talk Weatherproof Wall Stations 2 3 4 1 5 Installation & Operation
More informationLCT100. Load Cell Tester User s Guide (v1711) Anyload Transducer Co. Ltd Website:
LCT100 Load Cell Tester User s Guide (v1711) Anyload Transducer Co. Ltd Website: www.anyload.com Email: info@anyload.com A. Basic Steps in Load Cell Testing using the LCT100: 1. Connect the load cell cable
More informationHI 2204LT Loop Powered Level Weight Transmitter OPERATION AND INSTALLATION MANUAL
Loop Powered Level Weight Transmitter OPERATION AND INSTALLATION MANUAL Corporate Headquarters 9440 Carroll Park Drive San Diego, CA 92121 Phone: (858) 278-2900 FAX: (858) 278-6700 Web-Site: http://www.hardysolutions.com
More informationLPB OMNI Broadcast Transmitter Installation Procedure Checklist
Installation Procedure LPB OMNI Broadcast Transmitter Installation Procedure Checklist LPB Communications, Inc. 960 Brook Road, Unit 5 Conshohocken, PA 19428 610-825-4100 phone 610-825-4047 fax www.lpbinc.com!
More informationIMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Models: RB-G-K10, RB-TX10 IMPORTANT: THIS DEVICE MUST BE PROFESSIALLY INSTALLED READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate
More informationSarasota CM200 Sarasota HME900 Density Converter Electronics
Sarasota CM00 Sarasota HME00 Density Converter Electronics Users of Sarasota density meters or specific gravity analyzers are offered the choice of a HART compatible, field mounted density converter, or
More informationUnderwater GPS User Manual
Underwater GPS Document number W-DN-17002-2 Project Classification - Rev Prepared by Checked by Approved by Short description 1 2017-08-03 O. Skisland Initial 2 O. Skisland Minor changes References [1]
More informationModels included: GEO EDGE
Models included: GEO EDGE Printed in USA 12/04 P/N 118000 rev. A WARNING... Not To Be Used for Personnel Protection Never use this product as a sensing device for personnel protection. Doing so could lead
More informationScorpion Antennas Controller. Instruction Manual. Firmware V11.8 November Please Read This Manual Completely Before Operating The Controller
Firmware V11.8 November 2012 Please Read This Manual Completely Before Operating The Controller Contents Introduction:... 3 Installation:... 3 Using the Scorpion Antennas Controller... 5 Tuning Your Dipole...
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL AN25 Totalizer/ Rate Indicator DOC#: MN-AN25.doc Sponsler Co., Inc. AN25 Totalizer/Rate Indicator pg. 2 DOC#: MN-AN25 SPECIFICATIONS Temperature: Operating 0 to 70 C Storage
More informationSCXI TERMINAL BLOCK
CALIBRATION PROCEDURE SCXI -1303 TERMINAL BLOCK Introduction What Is Calibration? Why Should You Verify? How Often Should You Verify? This document contains information and step-by-step instructions for
More informationNEW DESIGN***DEM Part Number FRS***NEW DESIGN Low power 144 MHz Transverter for the Flex Radio System SDR-1000 Operating Specifications:
NEW DESIGN***DEM Part Number 144-28FRS***NEW DESIGN Low power 144 MHz Transverter for the Flex Radio System SDR-1000 Operating Specifications: Operating Voltage: 12.0-15.5 VDC, 13.8 nominal Current Drain:
More informationArbStudio Training Guide
ArbStudio Training Guide Summary This guide provides step by step instructions explaining how to create waveforms, use the waveform sequencer, modulate waveforms and generate digital patterns. The exercises
More informationANI-F-KW1. Multi-Format ANI Encoder For Kenwood Radios. Manual Revision: Covers Software Revisions: ANI-F: 1.
ANI-F-KW1 Multi-Format ANI Encoder For Kenwood Radios Manual Revision: 2009-02-04 Covers Software Revisions: ANI-F: 1.2 and higher This manual & product supports the following radios: Portable: TK-2180/3180
More informationProximity Transmitters and Seismic Vibration Transmitters
TM016 Velocity/ Acceleration Vibration Transmitter Introduction The TM016 is a solid state loop powered transmitter which provides a 4-20mA output proportional to the machine case vibration level. The
More informationOrtel (Lucent) Fiber Optic Interface AC
Ortel (Lucent) Fiber Optic Interface 144-701-1AC Serial Number March 11, 2010 CD P/N 098-00126-000 Revision B ORTEL (LUCENT) FIBER OPTIC INTERFACE 1. GENERAL INFORMATION... 1 1.1. SCOPE OF OPTION... 1
More informationSutron SatLink2 Troubleshooting Instructions
Sutron SatLink2 Troubleshooting Instructions A. SatLink2 (SL2) symptoms: Missing or partial data on LRGS (check DIS-MSG for frequency and EIRP; use HDR DCP Message header list. B. Equipment and tools needed:
More informationSCADA and Telemetry Solutions. SCADALink IO900. Modular Wireless I/O System. User Manual Version V1.3 for SCADALink IO900 BENTEK SYSTEMS LTD
Modular Wireless I/O System User Manual Version V. for BENTEK SYSTEMS LTD #, 0 Ave S.E. Calgary, AB, Canada TB 0L Ph:(0) Fax:(0) email: sales@scadalink.com web: The is a Modular Wireless I/O System that
More informationEDACS WALL MOUNT STATION. Maintenance Manual. Mobile Communications LBI-31838A TABLE OF CONTENTS
A Mobile Communications EDACS WALL MOUNT STATION TABLE OF CONTENTS SYSTEM BOARD & REGULATOR BOARD.......... LBI-31892 KEY/DISPLAY BOARD MAINTENANCE MANUAL.... LBI-31940 Maintenance Manual Printed in U.S.A.
More informationWireless 900 MHz Receiver
Overview and Identification The 900 MHz unit receives a repeated or re-transmitted RF signal from one or more wireless temperature or humidity transmitters. The signal from the transmitter (418 MHz) is
More informationHUMITRAN-RHT & RH RELATIVE HUMIDITY/TEMPERATURE TRANSMITTER RELATIVE HUMIDITY TRANSMITTER
HUMITRAN-RHT & RH RELATIVE HUMIDITY/TEMPERATURE TRANSMITTER RELATIVE HUMIDITY TRANSMITTER A. GENERAL DESCRIPTION The Tegam Model RH is a relative humidity transmitter; the Model RHT includes a temperature
More informationJCM TRAINING OVERVIEW WBA-XX
JCM TRAINING OVERVIEW WBA- Phone # (800) 683-7248 (702) 651 0000 Technical Support # (702) 651-3444 Fax # (702) 651-0214 E-mail techsupport@jcm-american.com Web Address http://www.jcm-american.com 1 2
More informationSPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack)
1993 Specifications CSJ 0924-06-147, etc. SPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack) 1. Description. This Item shall govern for furnishing, and
More informationMODEL AT-10 ANALOG TRANSMITTER
MODEL AT-10 ANALOG TRANSMITTER INSTALLATION & OPERATING MANUAL Industrial Weighing Systems 9 Richmond Street Picton, Ontario K0K 2T0 Phone: 613-921-0397 Fax: 613-476-5293 Web: www.iwsystems.ca info@iwsystems.ca
More informationAD-8100 & AD-8200 Servo Amplifiers
Instruction Manual IM-0607 AD-8100 & AD-8200 Servo Amplifiers Table of Contents General Information... 2 Basic Models... 3 Specifications... 3 Installation Wiring... 3 Setup & Calibration... 4-6 Troubleshooting
More informationNCS-C150 INSTRUCTION MANUAL Rev A. Collcomm Inc. Shipping Address 2310 Pendley Road Cumming, Georgia 30041
NCS-C150 INSTRUCTION MANUAL Rev A Collcomm Inc. d.b.a. NCS Shipping Address 2310 Pendley Road Cumming, Georgia 30041 Mailing Address 1595 Peachtree Parkway Suite 204-123 Cumming, Georgia 30041 Toll Free
More informationGTS High Frequency Pulser. Technical Bulletin
GTS High Frequency Pulser Technical Bulletin 02 Elster American Meter High Frequency Pulser System control and data acquisition in gas distribution networks begins with process sensors: sensors to detect
More informationG SERIES PRECISION METERS
Precision Meters PRECISION METERS The High Precision Meter line is the most accurate of the FLOMEC Turbine Meters and includes a traditional design. These meters come in a variety of sizes and fitting
More informationPhD Inline Vortex. Performance Specifications Accuracy. Operating Specifications
Description The Vortex PhD vortex shedding flowmeter measures process fluid flow by detecting the frequency at which vortices are shed from an obstruction in the process fluid line (the bluff body). A
More informationThe wireless alternative to expensive cabling...
The wireless alternative to expensive cabling... ELPRO 905U Wireless Solutions for Process Applications New Products... New Solutions The ELPRO 905U range of wireless I/O provides a low cost alternative
More informationServo Amplifier - Troubleshooting Guide
Haas Technical Documentation Servo Amplifier - Troubleshooting Guide Scan code to get the latest version of this document Translation Available There are four versions of Haas amplifiers. 30A [1], 45A
More informationGround Loops and other Buzz
This is Google's cache of http://blog.trix.com/maxtroller-arduino-control-for-maxtrac-radios. It is a snapshot of the page as it appeared on Jan 17, 2012 19:29:13 GMT. The current page could have changed
More informationCAME QP- V4.4 SPECIFICATION STANDARDS CABLE PLAN CABLE TYPES Z SERIES AUDIOCODE CONTROL SET FOR DOUBLE LEAF GATES
Z SERIES Technical Document AUDIOCODE CONTROL SET FOR DOUBLE LEAF GATES QP- V4.4 CAME V4.4 Rev 1.0 2/2005 STANDARDS SPECIFICATION The V4 audiocode control set is for double leaf swing gates using CAME
More informationWorldwide Manufacturer of Gas Detection Solutions. Transmitter EC 23. Operation Manual
Worldwide Manufacturer of Gas Detection Solutions Transmitter EC 23 Operation Manual Table of Contents For Your Safety...4 General Description...4 Electrical Connections...5 Zero Point Adjustment...5
More informationWireless Room Temperature and Humidity Transmitter (Units without Temperature Setpoint or Override) Installation and Operating Instructions
Wireless Temperature and Humidity Overview and Indentification The Wireless Temperature and Humidity measures the room temperature and Relative Humidity and transmits the data at 418MHz or 433MHz RF to
More informationDST-2000C. Direction Sensing Tachometer INSTRUCTION MANUAL
DST-2000C Direction Sensing Tachometer INSTRUCTION MANUAL Azonix-Dynalco, 3690 N. W. 53 Street, Ft. Lauderdale, FL 33309 U.S.A.! (954) 739-4300 Fax (954) 484-3376 www.dynalco.com mailbox@dynalco.com October
More informationDec, Hytera Customer Service Express
ISSUE 12 Dec, 2012 www.hytera.com Hytera Customer Service Express News and Events P2 Hytera Return Material Authorization (RMA) Policy Correspondence Column P4 PD78X/PD70X No Rx Audio on External Microphone/Speaker
More informationProduct Specification for model TT Transducer Tester Rev. B
TT Rev B April 20, 2010 Product Specification for model TT Transducer Tester Rev. B The Rapid Controls model TT Rev B transducer tester connects to multiple types of transducers and displays position and
More informationAdvanced Test Equipment Rentals ATEC (2832) Contents
i Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Contents Appendix B: IFR COM-120 Test Procedures...1 MT-4E Testing with the IFR COM-120 by Aerofl ex...1 General Set-Up
More information200GTL ALIGNMENT REVISION: 1.0 BURKE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06. Total Pages: 6 pages. Page:1 print date: 9/23/09
ALIGNMENT PROCEDURE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06 PREPARED BY: BURKE Total Pages: 6 pages Page:1 print date: 9/23/09 1 TEST CONDITION: 200GTL ALIGNMENT INSTRUCTION 1.0. TEST TEMPERTAURE: 77
More informationMagnetic Flowmeter Simulator
Quick Installation Guide Rosemount 8714D Magnetic Flowmeter Simulator Start Step 1: Change Transmitter Parameters Step 2: Connect the Rosemount 8714D Step 3: Perform Electronics Trim Step 4: Verify 8714D
More informationLPU-2127 User Manual
LPU-2127 User Manual Doc #9004169 Rev A1, 04/15 Table of Contents Introduction... iii Warranty and Warranty Restrictions... iv Chapter 1: Specifications and Options... 1 Dimensions...1 Specifications...
More informationMaintenance Manual. MTD SERIES 900 MHz, 10-WATT, DATA ONLY MOBILE RADIO. Mobile Communications LBI TABLE OF CONTENTS
Mobile Communications MTD SERIES 900 MHz, 10-WATT, DATA ONLY MOBILE RADIO TABLE OF CONTENTS RF BOARD............................... LBI-38545 AUDIO BOARD............................ LBI-38546 LOGIC BOARD............................
More informationNCS-C151 INSTRUCTION MANUAL Rev B. Collcomm Inc. d.b.a. NCS. Shipping Address 2310 Pendley Road Cumming, Georgia 30041
NCS-C151 INSTRUCTION MANUAL Rev B Collcomm Inc. d.b.a. NCS Shipping Address 2310 Pendley Road Cumming, Georgia 30041 Mailing Address 1595 Peachtree Parkway Suite 204-123 Cumming, Georgia 30041 Toll Free
More informationVOLTAGE. User Guide ACCESSORIES. External Sensor DT140. for MicroLog EC600 and EC V ±0.05V ±3% (before calibration)
External Sensor VOLTAGE DT140 Range: Resolution: Accuracy: Input impedance: Calibration: OV protection: 0-10V ±0.05V ±3% (before calibration) 3MΩ 2 calibration points ±30V ACCESSORIES User Guide for MicroLog
More informationIssue No: MG025 Date: 05 June McMurdo SmartFind R5 GMDSS Radio IMO MSC. 1/Circ Update procedure
Installation SERVICE BULLETIN Issue No: MG025 Date: 05 June 2017 McMurdo SmartFind R5 GMDSS Radio IMO MSC. 1/Circ. 1460 Update procedure Product Affected: McMurdo R5 GMDSS VHF Handheld Radio Reason: Compliance
More informationNon-Contact Sensing Reduces Wear, Breakage, Downtime, and Ultimately, Cost
TURCK Linear Displacement Transducers TURCK introduces a new line of linear displacement transducers (LDTs) called EZ-Track. EZ-Track is the latest offering in TURCK s continuous effort to change the shape
More information905U Wireless. New Products... New Solutions. The wireless alternative to expensive cabling... Simple but Reliable. Easy to Use
Wireless New Products... New Solutions The range of telemetry modules provide remote monitoring and control by radio or twisted-pair wire, over short or long distances. Transducer signals connected at
More informationOrtel (Lucent) Fiber Optic Interface
Ortel (Lucent) Fiber Optic Interface 144-701-1 Serial Number May 5, 2009 Revision B ORTEL (LUCENT) FIBER OPTIC INTERFACE 1. GENERAL INFORMATION... 1 1.1. SCOPE OF OPTION... 1 1.2. PURPOSE OF EQUIPMENT...
More informationM2M i-link POINT-TO-MULTIPOINT INSTALLATION INSTRUCTIONS
M2M i-link POINT-TO-MULTIPOINT INSTALLATION INSTRUCTIONS 1 TABLE OF CONTENTS 1 TABLE OF CONTENTS... 2 2 GENERAL... 3 3 INSTALLATION... 4 3.1 SUB-STATIONS... 4 3.2 MAIN STATION (PC)... 4 4 CONNECTING THE
More informationDual Band Filter Assembly Manual
Dual Band Filter Assembly Manual 12 January 2018 Rev D Version Theory of Operation: The purpose of a Bandpass Filter is to filter out or reject all unwanted signals. The original KN-Q7A Receive Filter
More informationSCXI HIGH-VOLTAGE ATTENUATOR TERMINAL BLOCK
CALIBRATION PROCEDURE SCXI -1313 HIGH-VOLTAGE ATTENUATOR TERMINAL BLOCK Introduction What Is Calibration? Why Should You Verify? How Often Should You Verify? This document contains information and step-by-step
More informationGlobal Water Instrumentation, Inc.
Global Water Instrumentation, Inc. 151 Graham Road P.O. Box 9010 College Station, TX 77842-9010 T: 800-876-1172 Int l: (979) 690-5560, Fax: (979) 690-0440 E-mail : globalw@globalw.com Radar Level Transmitters
More informationMass and Volume Flow Transmitter
IFT9701 Product Data Sheet PS-00218-EU December1999 Mass and Volume Flow Transmitter IFT9701 transmitter The IFT9701 microprocessor-based transmitter works with Micro Motion sensors to provide affordable,
More informationE7000, E7500, and E ma Analog Transmitters
E7000, E7500, and E8000 4-20 ma Analog Transmitters Installation, Operation and Maintenance Manual 24512-00 Rev. 1.8 6/8/16 3255 W. STETSON AVENUE HEMET, CA 92545-7799 Tel (951) 652-6811 Fax (951) 652-3078
More informationGPS Evaluation Kit EVA1035-H
GPS Evaluation Kit EVA1035-H A Description of the Evaluation Board for Vincotech s GPS Receiver / Smart Antenna Module A1035-H User s Manual Version 1.0 Hardware Revision 01 Revision History Rev. Date
More informationALX-SSB 5 Band Filter Assembly Manual 19 November 2018
ALX-SSB 5 Band Filter Assembly Manual 19 November 2018 Contents Theory of Operation:... 1 Figure 1... 2 Parts Included:... 4 Board Overview:... 5 Figure 2... 5 Figure 3... 5 Board Assembly:... 6 Cable
More informationANTENNAFIER TM 915LTX BLOCK DIAGRAM LNA
Digitally Tunable 0.5 to 10 Watts This 915 LTX is a Outdoor High Power Digitally Tunable Bi-Directional Amplifier for 802.11b/g WLAN. It s tuned and powered over a 50 Ohm coax. Now you can fine tune your
More informationMDX420 Input Level Field Calibration Procedure AN227 Rev. 1.0
MDX420 Input Level Field Calibration Procedure AN227 Rev. 1.0 Radyne Corporation 3138 E. Elwood St. Phoenix, AZ 85034 (602) 437-9620 Fax: (602) 437-4811 MDX420 Input Level Field Calibration Procedure AN227
More informationLUDLUM MODEL 421 AND PMT BASE WITH PREAMPLIFIER/BIAS SUPPLY. October 2014 Serial Number and Succeeding Serial Numbers
LUDLUM MODEL 421 AND 421-3 PMT BASE WITH PREAMPLIFIER/BIAS SUPPLY October 2014 Serial Number 200000 and Succeeding Serial Numbers LUDLUM MODEL 421 AND 421-3 PMT BASE WITH PREAMPLIFIER/BIAS SUPPLY October
More informationWelcome at MR Achieva 3.0T TX. About the system. Index. 1.1 Introduction
1 Welcome at MR Achieva 3.0T TX Welcome to the Introduction of and e-learning module for the Achieva 3 Tesla TX-system. This CBT is setup for those engineers who will soon receive a Achieva 3Tesla TX system.
More informationThe first RADIO Communication Module designed for the weighing industry
The first RADIO Communication Module designed for the weighing industry SCALELINK - AURORA WIRELESS LINK Step 1: Get Connected A) Disconnect the indicator (or other device) from power. Connect the ScaleLink
More informationWireless Interface RAD-ISM-900-SET-BD-BUS Two-way (point-to-point) Monitoring and Control with Expandable I/O Options User Manual
Wireless Interface RAD-ISM-900-SET-BD-BUS Two-way (point-to-point) Monitoring and Control with Expandable I/O Options User Manual ) ) ) ) ) ) ) ) ) ) ) ) Notice: These devices must be wired in accordance
More informationAmeritron ALS-600 Retrofit ALS-600-LPF Assembly Manual
Ameritron ALS-600 Retrofit ALS-600-LPF Assembly Manual FEATURES Automatic band change based on TX frequency. PIN diode QSK RX/TX switch. Temperature controlled FAN for quiet operation. RS-232 serial port
More informationOrtel (Lucent) Fiber Optic Interface
Ortel (Lucent) Fiber Optic Interface 144-701-1 Serial Number January 31, 2013 Part number 098-00120-000 Revision C ORTEL (LUCENT) FIBER OPTIC INTERFACE 1. GENERAL INFORMATION...1 1.1. SCOPE OF OPTION...1
More informationGS.No.GBN062E-5. GENERAL SPECIFICATIONS Sensor unit
High performance microflow Coriolis Flowmeter GENERAL SPECIFICATION GS.No. GENERAL Based on the Coriolis technologies accumulated over many years, the OVAL has broadened its current general purpose coriolis
More informationInput Voltage. Current Draw. Output. Resolution Internal Analog Output. Linearity. Repeatability. Hysteresis +/-.02% of Full Scale. Operating Pressure
BlueOx Magnetostrictive LDT for High Shock and Vibration Areas Gemco brand position sensing products have been known for survival in harsh industrial environments. We have taken over twenty years experience
More informationeguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards
eguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards A. Primary Technical Data: Transmitter Operating voltage DC 24V Operating current. < 450mA
More informationInstruction Manual MX-480 Bi-directional Multi-Protocol Data
Instruction Manual MX-480 Bi-directional Multi-Protocol Data Copyright 2007, American Fibertek, Inc. 1210JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...4
More informationEVDP610 IXDP610 Digital PWM Controller IC Evaluation Board
IXDP610 Digital PWM Controller IC Evaluation Board General Description The IXDP610 Digital Pulse Width Modulator (DPWM) is a programmable CMOS LSI device, which accepts digital pulse width data from a
More informationAirScope Spectrum Analyzer User s Manual
AirScope Spectrum Analyzer Manual Revision 1.0 October 2017 ESTeem Industrial Wireless Solutions Author: Date: Name: Eric P. Marske Title: Product Manager Approved by: Date: Name: Michael Eller Title:
More information